Download PDF Manual

. Normalization


Normalization This feature improves voice recognition and media groupings. See “CD Player,” “USB,” “Auxiliary Devices,” and “Bluetooth Audio” in the infotainment manual.


Select to enable or disable.


XM Channel Art This feature turns the XM Audio page background on the XM Channel display on and off. Select to enable or disable.


Max Startup Volume This feature sets the maximum startup volume. If the vehicle is started and the volume is greater than this level, the volume is adjusted to this level. Press + or − to increase or decrease the volume.


Number of Favorites Pages Press to set the number of favorites to display. Select the desired number.


XM Categories This allows which available XM Categories are used and displayed. Press to enable or disable available categories.


Software Versions Menu Press to display information about the system and update software if available. Phone Settings Select and the following may display: . Bluetooth


Bluetooth Select and the following may display: . Device List . Pair Device


Device List Select to connect to a different phone source, disconnect a phone, or delete a phone.


Pair Device Select to pair a new device. See “Pairing a Phone/Device” in “Bluetooth” in the infotainment manual.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (33,1)


Navigation Settings See “Navigation Settings” in “Configure Menu” in the infotainment manual. Display Settings Press and the following may display: . Home Page Menu . Rear Camera Options . Display Off . Map Settings


Home Page Menu Select and the following may display: . Customize . Sort . Restore Home Page Defaults


Customize This feature allows the selection of what icons will be on the first Home Page.


Instruments and Controls


5-33


Select and follow the screen prompts.


Sort This feature allows the icons on the Home Page to be moved. Select and follow the screen prompts.


Restore Home Page Defaults This feature will restore the Home Page to the factory settings. Select and follow the screen prompts.


Rear Camera Options Select and the following may display: . Symbols


Symbols Select to turn the rear camera symbols on or off. See Rear Vision Camera (RVC) on page 9-39.


Display Off Press to turn the display off. The display will return when any radio buttons are pressed or the screen is touched (if equipped). Map Settings See “Map Settings” in “Configure Menu” in the infotainment manual. Vehicle Settings Select and the following may display: . Climate and Air Quality . Comfort and Convenience . Collision/Detection Systems


Lighting


. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings?


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (34,1)


5-34


Instruments and Controls


Climate and Air Quality Select and the following may display: . Auto Fan Speed . Remote Start Heated Seats . Auto Defog . Auto Rear Defog


Auto Fan Speed This allows for selecting the automatic fan speed. It can be adjusted to run lower or higher than normal. Select High, Medium, or Low.


Remote Start Heated Seats When turned on, this feature will turn the heated seats on when using remote start on cold days. Select On or Off.


Auto Defog Only vehicles with dual automatic climate control will have this option. This allows for turning the auto defog on or off.


Select On or Off.


Auto Rear Defog This will allow for turning the auto rear defog on or off. This feature will automatically turn on the rear window defogger when it is cold outside. Select On or Off. Collision Detection Systems Select and the following may display: . Park Assist . Side Blind Zone Alert (SBZA) . Rear Cross Traffic Alert


Park Assist This allows the Park Assist feature to be turned on or off. Select On or Off. See Parking Assist on page 9-36.


Side Blind Zone Alert (SBZA) This allows the SBZA feature to be turned on or off.


Select On or Off. See Side Blind Zone Alert (SBZA) on page 9-37.


Rear Cross Traffic Alert This allows the feature to be turned on or off. Select Off or On. See Rear Vision Camera (RVC) on page 9-39. Comfort and Convenience Select and the following may display: . Easy Exit Driver Seat . Chime Volume . Reverse Tilt Mirror


Easy Exit Driver Seat This feature moves the seat rearward allowing the driver more room to exit the vehicle. See “Easy Exit Driver Seat” under Memory Seats on page 3-6. Select On or Off.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (35,1)


Chime Volume This allows selection of the chime volume level. Select Normal or High.


Reverse Tilt Mirror When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Reverse Tilt Mirrors on page 2-19. Select On or Off. Lighting Select and the following may display: . Vehicle Locator Lights . Exit Lighting


Instruments and Controls


5-35


Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. The vehicle locator lights come on when unlocking the vehicle with the RKE transmitter. Select On or Off.


Exit Lighting This allows for selecting how long the exterior lamps stay on when leaving the vehicle and it is dark outside. Select Off, 30 Seconds, 1 Minute, or 2 Minutes. Power Door Locks Select and depending on the radio the following may display: . Open Door Anti Lock Out . Unlocked Door Anti Lock Out . Auto Door Unlock . Delayed Door Lock . Auto Door Lock


Open Door Anti Lock Out or Unlocked Door Anti Lock Out When on, this feature will keep the driver door from locking when the door is open. If Off is selected, the Delayed Door Lock menu will be available and the door will lock as programmed through this menu. Select to turn On or Off.


Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park). Select All Doors, Driver Door, or Off.


Delayed Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. Three chimes will signal delayed locking is in use. Press either the power lock button or Q on the RKE transmitter twice to override the delayed locking feature and immediately lock all of the doors.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (36,1)


5-36


Instruments and Controls


Select to turn On or Off.


Auto Door Lock This allows selection of which of the doors will automatically lock when the vehicle is shifted out of P (Park). Select All Doors, Driver Door, or Off. Remote Lock/Unlock/Start Select and depending on the radio the following may display: . Remote Unlock Feedback . Unlock Feedback (Lights) . Remote Lock Feedback


Locking Feedback


. Remote Door Unlock . Door Unlock Options . Memory Remote Recall . Remote Left in Vehicle Reminder . Relock Remote Door . Passive Door Unlock . Passive Door Lock


Remote Unlock Feedback or Unlock Feedback (Lights) When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Select On or Off. Press TUNE/ MENU to confirm and go back to the last menu.


Remote Lock Feedback or Locking Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press TUNE/MENU when Locking Feedback is highlighted. Turn the TUNE/MENU knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press TUNE/MENU to confirm and go back to the last menu.


Remote Door Unlock or Door Unlock Options This allows selection of which doors will unlock when pressing K on the RKE transmitter.


Press TUNE/MENU when Door Unlock Options is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press TUNE/MENU to confirm and go back to the last menu.


Memory Remote Recall This allows the Memory Remote Recall feature to be turned on or off. When on, this feature will recall the current driver's last seat and outside mirror positions upon unlocking the driver door with the RKE transmitter, and opening that door. The current driver is identified when the RKE transmitter is used to unlock the driver door. If equipped with Keyless Access, the recall will occur upon opening the driver door. See “Recalling RKE Memory Positions” under Memory Seats on page 3-6.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (37,1)


Instruments and Controls


5-37


Return to Factory Settings? Select Return to Factory Settings? for the option to return all vehicle personalization to the default settings. Turn the TUNE/MENU knob to select Yes or No. Press TUNE/MENU to confirm and go back to the last menu.


Press TUNE/MENU when Memory Remote Recall is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.


Remote Left in Vehicle Reminder This allows the Remote Left in Vehicle Reminder feature to be turned on or off. If on, the horn will chirp if a remote is left in the vehicle. Press TUNE/MENU when Remote Left in Vehicle Reminder is highlighted. Turn the TUNE/MENU knob to select On or Off. Press TUNE/MENU to confirm and go back to the last menu.


Relock Remote Door When on, the doors will automatically lock after a period of time if the vehicle is not entered or exited. Press TUNE/MENU when Relock Remote Door is highlighted. Turn the TUNE/MENU knob to select On


or Off. Press TUNE/MENU to confirm and go back to the last menu.


Passive Door Unlock This allows selection of which doors are unlocked by pressing the button on the outside door handle. Press TUNE/MENU when Passive Door Unlock is highlighted. Turn the TUNE/MENU knob to select All Doors or Driver Door. Press TUNE/ MENU to confirm and go back to the last menu.


Passive Door Lock This allows for turning Passive Locking off, on, or on with feedback. Press TUNE/MENU when Passive Door Lock is highlighted. Turn the TUNE/MENU knob to select Off, On, or On with Active Horn Chirp. Press TUNE/MENU to confirm and go back to the last menu.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (38,1)


5-38


Instruments and Controls


Universal Remote System See Radio Frequency Statement on page 13-12.


Universal Remote System Programming


If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices.


Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door.


Make sure the hand-held transmitter has a new battery for quick and accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held


transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (39,1)


Instruments and Controls


5-39


2. At the same time, press and


hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2
with the procedure under “Radio Signals for Canada and Some Gate Operators” later in this section.


3. Press and hold the newly


programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.


If the indicator light stays on continuously or the garage door moves when the button is pressed, then


programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.


Learn or Smart Button 4. After completing Steps 1–3,


locate the Learn or Smart button inside garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.


5. Press and release the Learn or


6.


Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds and then release it. If the garage door does not move or the lamp on the garage door opener receiver


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (40,1)


5-40


Instruments and Controls


does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.


The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons. Radio Signals for Canada and Some Gate Operators For questions or programming help call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long


enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.


Universal Remote System Operation


Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.


2. Release both buttons.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (41,1)


Instruments and Controls


5-41


Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the


buttons. Do not release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (42,1)


5-42


Instruments and Controls


2 NOTES


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (1,1)


Lighting


Exterior Lighting


Exterior Lamp Controls . . . . . . . . 6-1
Exterior Lamps Off


Reminder . . . . . . . . . . . . . . . . . . . . 6-2


Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running


Lamps (DRL) . . . . . . . . . . . . . . . . 6-2


Automatic Headlamp


System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Fog Lamps . . . . . . . . . . . . . . . . . . . . 6-4


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-5


Lighting Features


Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-6
Battery Load Management . . . . 6-7


Lighting


6-1


Exterior Lighting


Exterior Lamp Controls


The exterior lamp control is on the instrument panel on the left side of the steering wheel. Turn the control to the following positions: O (Off): Turns off the exterior lamps. The knob returns to the AUTO position after it is released. Turn to O again to reactivate the AUTO mode. In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park).


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (2,1)


6-2


Lighting


AUTO (Automatic): Automatically turns the exterior lamps on and off, depending on outside lighting. ; (Parking Lamps): Turns on the parking lamps including all lamps, except the headlamps. 2 (Headlamps): Turns on the headlamps together with the parking lamps and instrument panel lights.


Exterior Lamps Off Reminder A warning chime sounds if the driver door is opened while the ignition is off and the exterior lamps are on.


Headlamp High/ Low-Beam Changer 2 3 (Headlamp High/Low-Beam Changer): Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.


The DRL system turns on the low-beam headlamps at a reduced brightness. For vehicles with High Intensity Discharge (HID) headlamps, there is a dedicated DRL. The DRL will come on when all of the following conditions are met:


The ignition is on. The exterior lamp control is in AUTO. The light sensor determines it is daytime. The vehicle is not in P (Park).


When the DRL are on, the taillamps, sidemarker lamps, instrument panel lights, and other lamps will not be on. The DRL turn off when the headlamps are turned to O or the ignition is off.


This indicator light turns on in the instrument cluster when the high-beam headlamps are on.


Flash-to-Pass To flash the high beams, pull the turn signal lever toward you, and release.


Daytime Running Lamps (DRL) DRL can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (3,1)


This vehicle may have a DRL disabling function. When the DRL are on and a turn signal is activated, the DRL on that side will be off until the turn signal goes off.


Automatic Headlamp System When the exterior lamp control is set to AUTO and it is dark enough outside, the headlamps come on automatically.


There is a light sensor on top of the instrument panel. Do not cover the sensor, otherwise the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel. When it is bright enough outside, the headlamps will turn off or may change to Daytime Running Lamps (DRL). The automatic headlamp system turns off when the exterior lamp control is turned to O or the ignition is off. Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are


Lighting


6-3


not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.


Hazard Warning Flashers


| (Hazard Warning Flashers): Press this button to make the front and rear turn signal lamps flash on and off. Press again to turn the flashers off. The hazard warning flashers turn on automatically if the airbags deploy.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (4,1)


6-4


Lighting


Turn and Lane-Change Signals


Move the turn signal lever all the way up or down to signal a turn. An arrow on the instrument cluster flashes in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. If the lever is briefly pressed and released, the turn signal flashes three times. The turn signal can be turned off manually by moving the lever back to its original position.


If after signaling a turn or lane change, the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have any burned out bulbs replaced. If a bulb is not burned out, check the fuse. See Fuses on page 10-34.


Fog Lamps


If the fog lamps are turned on while the exterior lamp control is in the AUTO position, the headlamps come on automatically. # (Fog Lamps, If Equipped): Press to turn on or off. An indicator light on the instrument cluster comes on when the fog lamps are on. Some localities have laws that require the headlamps to be on along with the fog lamps.


To turn on the fog lamps, if equipped, the ignition and the headlamps or parking lamps must be on.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (5,1)


Interior Lighting


Instrument Panel Illumination Control


Courtesy Lamps The courtesy lamps come on automatically when any door is opened and the dome lamp is in the door position.


Dome Lamps


Lighting


6-5


1 (Door): Turns the lamps on when any door is opened. + (On): Keeps the lamps on all the time.


Reading Lamps There are front and rear reading lamps in the overhead console and the headliner.


The brightness of the instrument panel lighting and steering wheel controls can be adjusted. D (Instrument Panel Illumination): Move and hold the thumbwheel up or down to brighten or dim the lights.


The interior lamps control in the overhead console controls both the front and rear interior lamps. To operate, press the buttons: E (Off): Turns the lamps off.


Front Reading Lamps


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (6,1)


6-6


Lighting


Rear Reading Lamps


# or $ (Reading Lamps): Press the button near each lamp to turn it on or off.


Lighting Features


Entry Lighting The headlamps, taillamps, license plate lamps, back-up lamps, dome lamps, and most of the interior lights turn on briefly when the Remote Keyless Entry (RKE) transmitter K button is pressed. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16. After about 30 seconds the exterior lamps turn off, then the dome lamps and remaining interior lights dim to off. Entry lighting can be disabled manually by changing the ignition out of the OFF position, or by pressing the RKE transmitter Q button. This feature can be changed. See Vehicle Personalization on page 5-31.


Exit Lighting The headlamps, taillamps, parking lamps, back-up lamps, and license plate lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamps also come on when the key is removed from the ignition. The exterior lights and dome lamps remain on after the door is closed for a set amount of time, then automatically turn off. For vehicles with Keyless Access, the exterior lamps automatically turn on when a door is opened after the ignition is turned off. The dome lamps come on after the ignition is changed to the OFF position. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16. The exterior lamps turn off immediately by turning the exterior lamps control off. This feature can be changed. See Vehicle Personalization on page 5-31.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (7,1)


Lighting


6-7


Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed and it is recommended that the driver reduce the electrical loads as much as possible. See Battery Voltage and Charging Messages on page 5-24.


A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories.


Battery Load Management The vehicle has Electric Power Management (EPM), which estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (8,1)


6-8


Lighting


2 NOTES


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (1,1)


Infotainment System


Introduction


Infotainment . . . . . . . . . . . . . . . . . . . 7-1
Theft-Deterrent Feature . . . . . . . 7-2
Overview . . . . . . . . . . . . . . . . . . . . . . 7-2
Operation . . . . . . . . . . . . . . . . . . . . . 7-4


Radio


AM-FM Radio . . . . . . . . . . . . . . . . . 7-8
Satellite Radio . . . . . . . . . . . . . . . 7-10
Radio Reception . . . . . . . . . . . . . 7-11
Backglass Antenna . . . . . . . . . . 7-12
Multi-Band Antenna . . . . . . . . . . 7-12


Audio Players


CD Player . . . . . . . . . . . . . . . . . . . 7-13
Auxiliary Devices . . . . . . . . . . . . 7-14


Phone


Bluetooth (Overview) . . . . . . . . 7-19
Bluetooth (Infotainment


Controls) . . . . . . . . . . . . . . . . . . . 7-21


Bluetooth (Voice


Recognition) . . . . . . . . . . . . . . . 7-24


Introduction


Infotainment Base radio information is included in this manual. See the infotainment manual for information on other available infotainment systems. Read the following pages to become familiar with these features.


{ Warning


Taking your eyes off the road for too long or too often while using any infotainment feature can cause a crash. You or others could be injured or killed. Do not give extended attention to infotainment tasks while driving. Limit your glances at the vehicle displays and focus your attention on driving. Use voice commands whenever possible.


Infotainment System 7-1


The infotainment system has built-in features intended to help avoid distraction by disabling some functions when driving. These functions may gray out when they are unavailable. Many infotainment features are also available through the instrument cluster and steering wheel controls. Before driving: . Become familiar with the


operation, faceplate buttons, and screen buttons.


. Set up the audio by presetting


favorite stations, setting the tone, and adjusting the speakers.


. Set up phone numbers in


advance so they can be called easily by pressing a single button or by using a single voice command if equipped with Bluetooth phone capability.


See Defensive Driving on page 9-3.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (2,1)


7-2


Infotainment System


To play the infotainment system with the ignition off, see Retained Accessory Power (RAP) on page 9-21.


Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identification Number (VIN) to the infotainment system. The infotainment system does not operate if it is stolen or moved to a different vehicle.


Overview


Infotainment System Overview Radio faceplate examples are provided to help identify buttons and to help understand the functions of the radio. Find the faceplate that best matches the vehicle for a description.


Radio with CD


1. VOL/ O (Volume/Power)


3. CD/AUX


Turns the system on or off and adjusts the volume.


2. FAV (Favorites)


Opens the favorites list.


Selects the CD player or external audio source. Selects a connected external audio source.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (3,1)


4. Buttons 1 to 6


9. v / > (Phone/Mute)


Saves and selects favorite stations. 5. RADIO/BAND


Changes the band while listening to the radio. Selects the radio when listening to a different audio source.


6. BACK /


Menu: Moves one level back. Character Input: Deletes the last character.


7. TUNE/MENU


Radio: Manually selects radio stations. CD: Selects tracks.


8. Z (CD Eject)


Removes a disc from the CD slot.


Opens the Phone menu. Mutes the audio system.


10. w j (Play/Pause)


Press to start, pause, and resume playback. See CD Player on page 7-13.


11. CD Slot


Insert a CD.


12. © SEEK ¨


Press © to seek to the beginning of the current or previous track. If the track has been playing for less than five seconds, it seeks the previous track. If longer than five seconds, the current track starts from the beginning. Press and hold © to quickly reverse through a track. Release the button


Infotainment System 7-3


to return to playing speed. See CD Player on page 7-13. For AM or FM, press © to seek to the previous strong station. Press ¨ to seek the next track. Press and hold ¨ to fast forward through a track. Release ¨ to return to playing speed. See CD Player on page 7-13. For AM or FM, press ¨ to seek to the next strong station.


13. CONFIG (Configuration)


Opens the Configuration menu.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (4,1)


7-4


Infotainment System


14. TONE


Press to access the Tone Settings menu to adjust bass, midrange, and treble. See Operation on page 7-4.


15.


INFO


Radio: Shows available information about the current station. CD: Shows available information about the current track.


Configuration Setup Menu Press the CONFIG button to display the Configuration menu. The Configuration menu is used for changing the settings for the audio, phone, vehicle configuration, and time features. Turn the TUNE/MENU knob to scroll through the available setup features. Once the desired feature displays, press the TUNE/MENU knob or


press the desired feature on the screen, to display more options within that feature. Languages To change the display language, see Vehicle Personalization on page 5-31. The vehicle supports English, French, and Spanish. The default language is English.


Operation


Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, menus shown on the display, and steering wheel controls, if equipped. Turning the System On or Off VOL/ O (Volume/Power): Press to turn the system on and off.


Automatic Switch-Off If the infotainment system has been turned on after the ignition is turned off, the system will turn off automatically after 10 minutes. Volume Control VOL/ O (Volume/Power): Turn to adjust the volume. v / > (Phone): For vehicles with OnStar, press and hold v / > to mute the infotainment system. Press and hold v / > again, or turn the VOL/ O knob to cancel mute. For vehicles without OnStar®, press v / > to mute the infotainment system. Press v / > again, or turn the VOL/ O knob to cancel mute. Menu System


Controls The TUNE/MENU knob and the BACK / button are used to navigate the menu system.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (5,1)


TUNE/MENU: Press to: . Select or activate the highlighted


menu option.


. Confirm a set value.


Turn a system setting on or off.


Turn to: . Enter the menu system. . Highlight a menu option. . Select a value. BACK / : Press to: . Exit a menu. . Return from a submenu screen


to the previous menu screen. . Delete the last character in a


sequence.


Selecting a Menu Option The base radio displays one line of text at a time.


Infotainment System 7-5


Activating a Setting


1. Turn the TUNE/MENU knob to


move the highlighted bar.


2. Press TUNE/MENU to select the


highlighted option.


Submenus


1. Turn the TUNE/MENU knob to


highlight the setting.


2. Press TUNE/MENU to activate


the setting.


Setting a Value


An arrow on the right-hand edge of the menu indicates that it has a submenu with other options.


1. Turn the TUNE/MENU knob to change the current value of the setting.


2. Press TUNE/MENU to confirm


the setting.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (6,1)


7-6


Infotainment System


Turning a Function On or Off


1. Turn the TUNE/MENU knob to


highlight the function.


2. Press TUNE/MENU to turn the


function on or off.


Entering a Character Sequence


1. Turn the TUNE/MENU knob to


highlight the character.


2. Press TUNE/MENU to select the


character.


Press the BACK / button to delete the last character in the sequence or press and hold to delete the entire character sequence. Audio Settings The audio settings can be set for each radio band and each audio player source. To quickly reset an audio setting value to 0: 1. Press the TONE button. 2. Select the audio setting. 3. Press and hold TUNE/MENU until the value changes to 0. Press the BACK / button to go back to the Tone Settings menu.


Adjusting the Treble, Midrange, and Bass


1. Press the TONE button. 2. Select Treble, Midrange,


or Bass.


3. Select the value. Press the BACK / button to go back to the Tone Settings menu.


Adjusting the Fader and Balance


1. Press the TONE button. 2. Select Fader or Balance.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (7,1)


3. Select the value. Press the BACK / button to go back to the Tone Settings menu.


Adjusting the EQ (Equalizer) For vehicles that have an equalizer: 1. Press the TONE button. 2. Select EQ. 3. Select the setting. Press the BACK / button to go back to the Tone Settings menu. System Settings


Speed Compensated Volume


road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent. The level of volume compensation can be selected, or the auto volume feature can be turned off. 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Speed compensated


volume.


4. Select the setting. 5. Press BACK / button to go back


to the System Configuration menu.


Configuring the Number of Favorite Pages


The Speed Compensated Volume feature automatically adjusts the radio volume to compensate for


Infotainment System 7-7


To configure the number of available favorite pages: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Radio Favorites. 4. Select the number of available


favorite pages.


5. Press the BACK / button to go


back to the System Configuration menu.


Auto Volume The auto volume feature automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent. The level of volume compensation can be selected, or the auto volume feature can be turned off.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (8,1)


7-8


Infotainment System


1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Auto Volume. 4. Select the setting. 5. Press the BACK / button to go


back to the System Configuration menu.


Maximum Startup Volume The maximum volume played when the radio is first turned on can be set.


1. Press the CONFIG button.


2. Select Radio Settings. 3. Select Maximum Startup


Volume.


4. Select the setting. 5. Press the BACK / button to go


back to the System Configuration menu.


Regionalization RDS stations will broadcast different programs on different frequencies. To set the Regional (REG) feature on or off: 1. Press the CONFIG button. 2. Select Regional (REG). 3. Select On or Off. 4. Press BACK / to go back to the


previous menu.


Radio


AM-FM Radio


Control Buttons The buttons used to control the radio are: RADIO/BAND: Press to turn the radio on and choose between AM, FM, or SiriusXM if equipped. TUNE/MENU: Press and turn to navigate the available menus. Turn to manually change stations. INFO: Press to display additional information that may be available for the current song. © SEEK ¨ : Press to search for stations. FAV: Press to open the favorites list. 1 to 6: Press to select preset stations.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (9,1)


RDS (Radio Data System) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This feature only works when the information from the radio station is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. While the radio is tuned to an FM-RDS station, the station name or call letters display. Radio Menus Radio menus are available for AM, FM, or SiriusXM if equipped. Turn the TUNE/MENU knob to open the main radio menu for that frequency.


Selecting a Band Press the RADIO/BAND button to choose AM, FM, or SiriusXM if equipped. The last station that was playing starts playing again. Selecting a Station


Seek Tuning If the radio station is not known: Briefly press © or ¨ to automatically search for the next available station. If a station is not found, the radio switches to a more sensitive search level. If a station still is not found, the frequency that was last active begins to play. If the radio station is known: Press and hold © or ¨ until the station on the display is reached, then release the button.


Manual Tuning Turn the TUNE/MENU knob to select the frequency on the display.


Infotainment System 7-9


Favorites List 1. Turn the TUNE/MENU knob. 2. Select Favorites List. 3. Select the station.


Station Lists 1. Turn the TUNE/MENU knob. 2. Select AM or FM Station List. All receivable stations in the current reception area are displayed. If a station list has not been created, an automatic station search is done.


3. Select the station.


Category Lists Most stations that broadcast an RDS program type code specify the type of programming transmitted. Some stations change the program type code depending on the content. The system stores the RDS stations sorted by program type in the FM category list.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (10,1)


7-10


Infotainment System


To search for a programming type determined by station: 1. Turn the TUNE/MENU knob. 2. Select FM category list. A list of all programming types available displays.


3. Select the programming type. A list of stations that transmit programming of the selected type displays.


4. Select the station.


The category lists are updated when the station lists are updated.


Updating Station & Category Lists If stations stored in the station list can no longer be received: 1. Turn the TUNE/MENU knob. 2. Select Update AM or FM Station List, if the stations stored in the station list are no longer received. A station search will be completed and the first station in the updated list will play.


To cancel the station search, press TUNE/MENU. Storing a Station as a Favorite Stations from all bands can be stored in any order in the favorite pages. Up to six stations can be stored in each favorite page and the number of available favorite pages can be set.


Storing Stations To store the station to a position in the list, press the corresponding button 1 to 6 until a beep is heard.


Retrieving Stations Press the FAV button to open a favorite page or to switch to another favorite page. Briefly press one of the 1 to 6 buttons to retrieve the station.


Satellite Radio


SiriusXM® Satellite Radio Service If equipped, vehicles with a SiriusXM satellite radio tuner and a SiriusXM satellite radio subscription can receive SiriusXM programming. SiriusXM is a satellite radio service based in the 48 contiguous United States and 10 Canadian provinces. SiriusXM satellite radio has a wide variety of programming and commercial-free music, coast to coast, and in digital-quality sound. A service fee is required to receive the SiriusXM service. For more information, see www.siriusxm.com or 1-866-635-2349 (U.S.), and www.xmradio.ca or 1-877-209-0079
(Canada). When SiriusXM is active, the channel name and number, category name, song title, and artist display on the screen.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (11,1)


SiriusXM Categories SiriusXM channels are organized in categories. To customize which SiriusXM categories are used and displayed in the system, see “Adding or Removing SiriusXM Categories” following. Adding or Removing SiriusXM Categories 1. Press the CONFIG button on the


faceplate.


2. Select Radio Settings. 3. Select Add/Remove XM


Categories.


4. From the Add/Remove XM


Categories screen, select or deselect any category to be used in XM mode. A checkmark will indicate that the category is selected.


Turning SiriusXM Channel Graphic On or Off 1. Press the CONFIG button on the


faceplate.


2. Select Radio Settings. 3. Select XM Channel Graphic to


turn on or off.


Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. FM FM signals only reach about 16 to 65 km (10 to 40 mi). Although the radio has a built-in electronic circuit that automatically works to reduce interference, some static can occur,


Infotainment System 7-11


especially around tall buildings or hills, causing the sound to fade in and out. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. Static can occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio. SiriusXM Satellite Radio Service If equipped, SiriusXM Satellite Radio Service provides digital radio reception. Tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the SiriusXM signal for a period of time.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (12,1)


7-12


Infotainment System


Cell Phone Usage Cell phone usage, such as making or receiving phone calls, charging, or just having the phone on may cause static interference with the radio. Unplug the phone or turn it off if this happens.


Backglass Antenna The AM-FM antenna is integrated with the rear window defogger in the rear window. Do not scratch the inside surface or damage the lines in the glass. If the inside surface is damaged, it could interfere with radio reception. For proper radio reception, the antenna connector needs to be properly attached to the post on the glass. If attaching a cell phone antenna to the glass, attach it between the grid lines.


{ Caution


Using a razor blade or sharp object to clear the inside rear window can damage the rear window antenna and/or the rear window defogger. Repairs would not be covered by the vehicle warranty. Do not clear the inside rear window with sharp objects.


{ Caution


Do not apply aftermarket glass tinting with metallic film. The metallic film in some tinting materials will interfere with or distort the incoming radio reception. Any damage caused to the backglass antenna due to metallic tinting materials will not be covered by the vehicle warranty.


Multi-Band Antenna The multi-band antenna is on the roof of the vehicle. The antenna is used for OnStar, the SiriusXM Satellite Radio Service System, and GPS (Global Positioning System), if the vehicle has these features. Keep the antenna clear of obstructions for clear reception. If the vehicle has a sunroof, and it is open, reception can also be affected.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (13,1)


Audio Players


CD Player The player can be used for CDs and MP3s. With the ignition on, insert a CD into the slot, label side up. The player pulls it in and begins playing. The vehicle must be in P (Park) for video to display. The system is capable of playing: . Most audio CDs . CD-R . CD-RW . MP3 or unprotected WMA


formats


When playing any compatible recordable disc, the sound quality can be reduced due to disc quality, the method of recording, the quality of the music or video that has been recorded, or the way the disc has been handled.


To avoid damage to the CD player: . Do not use scratched or


damaged discs.


. Do not apply labels to discs. The


labels could get caught in the player. Insert only one disc at a time.


. Keep the loading slot free of foreign materials, liquids, and debris.


If a description label is needed, try labeling the top of the disc using a marking pen. Loading and Ejecting Discs To load a disc: 1. Turn the ignition on. 2.


Insert a disc into the slot. The player pulls it in the rest of the way. If the disc is damaged or improperly loaded, there is an error and the disc ejects.


The disc automatically plays once loaded.


Infotainment System 7-13


Press Z to eject a disc from the CD player. Playing an Audio CD CD/AUX: Press to use the CD player. w j (Play/Pause): Use to start, pause, or resume play. © SEEK ¨: . Press © to seek to the beginning of the current or previous track. If the track has been playing for less than five seconds, it seeks the previous track. If longer than five seconds, the current track starts from the beginning.


. Press and hold © to quickly


reverse through a track. Release the button to return to playing speed. For AM or FM, press © to seek to the previous strong station. . Press ¨ to seek the next track.


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (14,1)


7-14


Infotainment System


. Press and hold ¨ to fast forward


through a track.


. Release ¨ to return to playing


speed.


TUNE/MENU: Turn to the right or left to select the next or previous track. Press this knob to select the menu. If a track is selected from the list, the system plays the track and returns to the CD screen. Error Messages If Disc Read Error displays and/or the disc comes out, it could be for one of the following reasons: The disc has an invalid or unknown format. The disc is not from a correct region. The disc is very hot. Try the disc again when the temperature returns to normal. The road is very rough. Try the disc again when the road is smoother.


The disc is dirty, scratched, wet, or upside down. The air is very humid. Try the disc again later. There was a problem while burning the disc. The label is caught in the CD player.


If the CD is not playing correctly, for any other reason, try a known good CD. If any error continues, contact your dealer.


Auxiliary Devices This vehicle may have an auxiliary input jack and USB port in the center console. See Center Console Storage on page 4-2. Portable devices are controlled by using the menu system described in Overview on page 7-2. Keep the storage area closed when not in use.


Auxiliary Input Jack Possible auxiliary audio sources include:


Laptop computer


. MP3 player Tape player


This jack is not an audio output. Do not plug headphones into the auxiliary input jack. Auxiliary devices should be set up while the vehicle is in P (Park). Connect a 3.5 mm (1/8 in) cable from the auxiliary device to the auxiliary input jack. When a device is connected, the system automatically begins playing audio from the device over the vehicle speakers. If an auxiliary device has already been connected, but a different source is currently active, press the CD/AUX button on the radio faceplate, then press SOURCE


Chevrolet Malibu Owner Manual 7575972) - 2015 - crc - 4/1/14


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (15,1)


Searching for a Track Tracks can be searched for by: . Playlists . Artists . Albums . Song Titles . Podcasts . Genres . Audiobooks . Composers To search for tracks: 1. Turn the TUNE/MENU knob. 2. Select Search. 3. Select: Playlists, Artists, Albums,


Song Titles, Podcasts, Genres, Audiobooks, or Composers.


4. Select the track.


Infotainment System 7-15


Shuffle

Loading...
x