You may also be interested in...
Download PDF Manual

7 257 kg (16,000 lb)


3 357 kg (7,400 lb) 4 536 kg (10,000 lb)


5 897 kg (13,000 lb) 7 257 kg (16,000 lb)


3 221 kg (7,100 lb) 4 536 kg (10,000 lb)


5 897 kg (13,000 lb) 7 257 kg (16,000 lb)


4 400 kg (9,700 lb)


7 257 kg (16,000 lb)


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (55,1)


Vehicle G3500 Passenger Van 2WD Long Wheelbase


Axle Ratio


Maximum Trailer Weight


GCWR*


Driving and Operating


9-55


6.0L V8


7 257 kg (16,000 lb) *The Gross Combined Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment, and conversion. The GCWR for the vehicle should not be exceeded.


4 218 kg (9,300 lb)


3.42


Ask your dealer for trailering information or advice. Weight of the Trailer Tongue The tongue load (1) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.


If there are a lot of options, equipment, passengers, or cargo in the vehicle, it will reduce the tongue weight the vehicle can carry, which will also reduce the trailer weight the vehicle can tow. If towing a trailer, the tongue load must be added to the GVW because the vehicle will be carrying that weight, too. See Vehicle Load Limits on page 9-10
for more information about the vehicle's maximum load capacity.


The trailer tongue weight (1) should be 10 percent to 15 percent of the total loaded trailer weight (2), up to a maximum of 181 kg (400 lb) with a weight carrying hitch. The trailer tongue weight (1) should be


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (56,1)


9-56


Driving and Operating


10 percent to 15 percent of the total loaded trailer weight (2), up to a maximum of 454 kg (1,000 lb) with a weight distributing hitch. Do not exceed the maximum allowable tongue weight for the vehicle. Choose the shortest hitch extension that will position the hitch ball closest to the vehicle. This will help reduce the effect of trailer tongue weight on the rear axle. After loading the trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper. If they are not, adjustments might be made by moving some items around in the trailer. Trailering may be limited by the vehicle's ability to carry tongue weight. Tongue weight cannot cause the vehicle to exceed the GVWR (Gross Vehicle Weight Rating) or the RGAWR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the total of the additional weight.


It is important that the vehicle does not exceed any of its ratings — GCWR, GVWR, RGAWR, Maximum Trailer Rating, or Tongue Weight. The only way to be sure it is not exceeding any of these ratings is to weigh the vehicle and trailer. Total Weight on the Vehicle's Tires Be sure the vehicle tires are inflated to the upper limit for cold tires. These numbers can be found on the Certification label at the rear edge of the driver door, or see Vehicle Load Limits on page 9-10. Make sure not to go over the GVW limit for the vehicle, or the GAWR, including the weight of the trailer tongue. If using a weight distributing hitch, make sure not to go over the rear axle limit before applying the weight distribution spring bars.


Towing Equipment


Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. Weight-Distributing Hitches and Weight Carrying Hitches


1. Body to Ground Distance 2. Front of Vehicle


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (57,1)


Driving and Operating


9-57


When using a weight-distributing hitch, the hitch must be adjusted so the distance (1) remains the same both before and after coupling the trailer to the tow vehicle. If a step-bumper hitch will be used, the bumper could be damaged in sharp turns. Make sure there is ample room when turning to avoid contact between the trailer and the bumper. If the loaded trailer being pulled will weigh more than 2 270 kg (5,000 lb), be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving. Always use a sway control if the trailer will weigh more than these limits. Ask a hitch dealer about sway controls. Will any holes need to be made in the body of the vehicle when a trailer hitch is installed?


If using the wiring provided with the factory-installed trailering package, no holes need to be made in the body of the vehicle. However, if an aftermarket hitch is installed, holes may need to be made in the body. If holes are made in the body, then be sure to seal the holes later when the hitch is removed. If the holes are not sealed, deadly carbon monoxide (CO) from the engine's exhaust can get into the vehicle as well as dirt and water. See “Carbon Monoxide” under Engine Exhaust on page 9-22. Safety Chains Always attach chains between the vehicle and the trailer. Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Always leave just enough slack so the rig can turn. Never allow safety chains to drag on the ground.


Trailer Brakes A loaded trailer that weighs more than 680 kg (1,500 lb) needs to have its own brake system that is adequate for the weight of the trailer. Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly. Trailer Wiring Harness The optional heavy-duty trailer wiring package includes a wiring harness, with a seven-pin connector at the rear of the vehicle and a four-wire harness assembly under the driver side of the instrument panel. The four-wire harness assembly comes without a connector. If the vehicle does not have a trailer hitch, the seven-wire harness assembly with connector is taped together and located in a frame pocket at the driver side rear left corner of the frame.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (58,1)


9-58


Driving and Operating


If the vehicle has a trailer hitch, the seven-wire harness assembly with connector is attached to a bracket on the hitch platform. In both cases, the seven-wire harness has a connector and includes a 30-amp feed wire. The seven-wire harness connector contains the following trailer circuits:


Light Green: Back-up Lamps (10A fuse)**


. White: Ground . Dark Blue: Trailer Brake Signal . Dark Green: Right Rear Stop


and Turn Signal*


. Red/Black Stripe: Battery Feed


(30A Fuse)


. Brown: Trailer Park Lamp


Supply Voltage (15A fuse)**


. Yellow: Left Rear Stop and Turn


Signal *


The four-wire harness (without connector) contains the following circuits: . Black: Ground . Red/White: Battery Feed . Dark Blue: Trailer Brake Signal


Light Blue: CHMSL/Stoplamp Supply Voltage


* If the vehicle is a cutaway with trailer provisions, a 15 amp fuse will be shared for both left/stop trailer turn and right/stop trailer turn signals. However, the cutaway lighting connector will have a 10 amp fuse for each signal. ** If the vehicle is a cutaway with trailer provisions, a 15 amp fuse will be shared for trailer park lamps and cutaway rear lighting connector park lamps. Also, a 10 amp fuse will be shared for trailer back-up lamps and cutaway rear lighting connector back-up lamps.


Tow/Haul Mode This button is on the instrument panel, to the right of the steering wheel. Pressing this button turns on and off the Tow/Haul Mode.


This indicator light on the instrument cluster comes on when the Tow/ Haul Mode is on. Tow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load. See Tow/Haul Mode on page 9-30.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (59,1)


Operating the vehicle in Tow/Haul Mode when lightly loaded or with no trailer at all will not cause damage. However, there is no benefit to the selection of Tow/Haul when the vehicle is unloaded. Such a selection when unloaded may result in unpleasant engine and transmission driving characteristics and reduced fuel economy. Tow/ Haul is recommended only when pulling a heavy trailer or a large or heavy load.


Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle Gross Combined Weight Rating (GCWR). See “Weight of the Trailer” in Trailer Towing on page 9-51. Tow/Haul is most useful under the following driving conditions: . When pulling a heavy trailer or a


large or heavy load through rolling terrain.


. When pulling a heavy trailer or a


large or heavy load in stop-and-go traffic.


. When pulling a heavy trailer or a


large or heavy load in busy parking lots where improved low speed control of the vehicle is desired.


Driving and Operating


9-59


Conversions and Add-Ons


Add-On Electrical Equipment


{ Caution


Some electrical equipment can damage the vehicle or cause components to not work and would not be covered by the warranty. Always check with your dealer before adding electrical equipment.


Add-on equipment can drain the vehicle's 12-volt battery, even if the vehicle is not operating. The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing the Airbag-Equipped Vehicle on page 3-30 and Adding Equipment to the Airbag-Equipped Vehicle on page 3-30.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (60,1)


9-60


Driving and Operating


2 NOTES


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (1,1)


Vehicle Care


10-1


Vehicle Care


General Information


General Information . . . . . . . . . . 10-2
California Proposition


65 Warning . . . . . . . . . . . . . . . . . 10-3


California Perchlorate


Materials Requirements . . . . 10-3


Accessories and


Modifications . . . . . . . . . . . . . . . 10-3


Vehicle Checks Doing Your Own


Service Work . . . . . . . . . . . . . . . 10-4
Hood . . . . . . . . . . . . . . . . . . . . . . . . 10-4
Engine Compartment


Overview . . . . . . . . . . . . . . . . . . . 10-6
Engine Oil . . . . . . . . . . . . . . . . . . . 10-7
Engine Oil Life System . . . . . 10-10
Automatic Transmission Fluid


(4-Speed Transmission) . . . 10-11


Automatic Transmission


Fluid (6-Speed Transmission) . . . . . . . . . . . . . 10-13
Engine Air Cleaner/Filter . . . . 10-16
Cooling System . . . . . . . . . . . . 10-17
Engine Coolant . . . . . . . . . . . . . 10-18
Engine Overheating . . . . . . . . 10-22


Engine Fan . . . . . . . . . . . . . . . . . 10-23
Power Steering Fluid . . . . . . . 10-24
Washer Fluid . . . . . . . . . . . . . . . 10-25
Brakes . . . . . . . . . . . . . . . . . . . . . 10-25
Brake Fluid . . . . . . . . . . . . . . . . . 10-26
Battery . . . . . . . . . . . . . . . . . . . . . 10-28
All-Wheel Drive . . . . . . . . . . . . . 10-29
Front Axle . . . . . . . . . . . . . . . . . . 10-29
Rear Axle . . . . . . . . . . . . . . . . . . 10-30
Noise Control System . . . . . . 10-30
Starter Switch Check . . . . . . . 10-31
Automatic Transmission Shift


Lock Control Function Check . . . . . . . . . . . . . . . . . . . . . 10-32


Ignition Transmission Lock


Check . . . . . . . . . . . . . . . . . . . . . 10-32


Park Brake and P (Park)


Mechanism Check . . . . . . . . 10-32


Wiper Blade


Replacement . . . . . . . . . . . . . . 10-33


Headlamp Aiming


Headlamp Aiming . . . . . . . . . . 10-33


Bulb Replacement


Bulb Replacement . . . . . . . . . . 10-34
Halogen Bulbs . . . . . . . . . . . . . . 10-34
Headlamps . . . . . . . . . . . . . . . . . 10-34


Front Turn Signal,


Sidemarker, and Parking Lamps . . . . . . . . . . . . . . . . . . . . 10-36
Taillamps . . . . . . . . . . . . . . . . . . . 10-36
Center High-Mounted


Stoplamp (CHMSL) . . . . . . . 10-37
License Plate Lamp . . . . . . . . 10-38
Replacement Bulbs . . . . . . . . . 10-38


Electrical System


Electrical System


Overload . . . . . . . . . . . . . . . . . . 10-39


Fuses and Circuit


Breakers . . . . . . . . . . . . . . . . . . 10-40


Engine Compartment Fuse


Block . . . . . . . . . . . . . . . . . . . . . 10-40


Floor Console Fuse


Block . . . . . . . . . . . . . . . . . . . . . 10-43


Wheels and Tires


Tires . . . . . . . . . . . . . . . . . . . . . . . . 10-46
All-Season Tires . . . . . . . . . . . . 10-47
Winter Tires . . . . . . . . . . . . . . . . 10-47
All-Terrain Tires . . . . . . . . . . . . 10-48
Tire Sidewall Labeling . . . . . . 10-48
Tire Designations . . . . . . . . . . . 10-51
Tire Terminology and


Definitions . . . . . . . . . . . . . . . . 10-52
Tire Pressure . . . . . . . . . . . . . . . 10-55


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (2,1)


10-2


Vehicle Care


Towing the Vehicle


Towing the Vehicle . . . . . . . . . 10-83
Recreational Vehicle


Towing . . . . . . . . . . . . . . . . . . . . 10-83


Appearance Care


Exterior Care . . . . . . . . . . . . . . . 10-86
Interior Care . . . . . . . . . . . . . . . . 10-91
Floor Mats . . . . . . . . . . . . . . . . . . 10-94


General Information For service and parts needs, visit your dealer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks:


Tire Pressure Monitor


System . . . . . . . . . . . . . . . . . . . 10-56


Tire Pressure Monitor


Operation . . . . . . . . . . . . . . . . . 10-57
Tire Inspection . . . . . . . . . . . . . . 10-61
Tire Rotation . . . . . . . . . . . . . . . 10-61
Dual Tire Rotation . . . . . . . . . . 10-62
When It Is Time for New


Tires . . . . . . . . . . . . . . . . . . . . . . 10-63
Buying New Tires . . . . . . . . . . . 10-64
Different Size Tires and


Wheels . . . . . . . . . . . . . . . . . . . 10-65


Uniform Tire Quality


Grading . . . . . . . . . . . . . . . . . . . 10-66


Wheel Alignment and Tire


Balance . . . . . . . . . . . . . . . . . . . 10-67
Wheel Replacement . . . . . . . . 10-68
Tire Chains . . . . . . . . . . . . . . . . . 10-68
If a Tire Goes Flat . . . . . . . . . . 10-69
Tire Changing . . . . . . . . . . . . . . 10-71
Full-Size Spare Tire . . . . . . . . 10-79


Jump Starting


Jump Starting . . . . . . . . . . . . . . 10-79


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (3,1)


Accessories and Modifications Adding non‐dealer accessories or making modifications to the vehicle can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control, and stability control. These accessories or modifications could even cause malfunction or damage not covered by the vehicle warranty.


Vehicle Care


10-3


Damage to vehicle components resulting from modifications or the installation or use of non‐GM certified parts, including control module or software modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts. GM Accessories are designed to complement and function with other systems on the vehicle. See your dealer to accessorize the vehicle using genuine GM Accessories installed by a dealer technician. Also, see Adding Equipment to the Airbag-Equipped Vehicle on page 3-30.


California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.


California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, safety belt pretensioners, and lithium batteries contained in Remote Keyless Entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/ perchlorate.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (4,1)


10-4


Vehicle Care


Vehicle Checks


Doing Your Own Service Work


{ Warning


It can be dangerous to work on your vehicle if you do not have the proper knowledge, service manual, tools, or parts. Always follow owner manual procedures and consult the service manual for your vehicle before doing any service work.


If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 13-11.


Hood To open the hood:


1. Pull the handle with this symbol


on it. It is in front of the driver side door frame near the floor.


This vehicle has an airbag system. Before attempting to do your own service work, see Servicing the Airbag-Equipped Vehicle on page 3-30. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Records on page 11-15.


{ Caution Even small amounts of contamination can cause damage to vehicle systems. Do not allow contaminants to contact the fluids, reservoir caps, or dipsticks.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (5,1)


Vehicle Care


10-5


2. Go to the front of the vehicle and


lift up the secondary hood release, which is underneath the middle of the hood.


Before closing the hood, be sure all of the filler caps are on properly. Then lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the hood and return the prop to its retainer. Let the hood down and close it firmly.


3. Lift the hood, release the hood prop from its retainer, and put the hood prop into the slot in the hood.


If the vehicle has an underhood lamp, it will automatically come on and stay on until the hood is closed.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (6,1)


10-6


Vehicle Care


Engine Compartment Overview


4.3L V6 Engine Shown (4.8L V8 Engine, 5.3L V8 Engine, and 6.0L V8 Engine Similar)


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (7,1)


1. Battery on page 10-28. 2. Radiator Pressure Cap. See


Cooling System on page 10-17.


3. Coolant Recovery Tank. See


Cooling System on page 10-17.


4. Automatic Transmission Fluid


Dipstick. See “Checking the Fluid Level” under Automatic Transmission Fluid (4-Speed Transmission) on page 10-11 or Automatic Transmission Fluid (6-Speed Transmission) on page 10-13.


5. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 10-7.


6. Engine Oil Dipstick. See


“Checking Engine Oil” under Engine Oil on page 10-7.


7. Engine Air Cleaner/Filter on


page 10-16.


8. Power Steering Fluid Reservoir.


See Power Steering Fluid on page 10-24.


9. Brake Master Cylinder


Reservoir. See Brake Fluid on page 10-26.


10. Windshield Washer Fluid


Reservoir. See “Adding Washer Fluid” under Washer Fluid on page 10-25.


Engine Oil For diesel engine vehicles, see “Engine Oil” in the Duramax diesel supplement. To ensure proper engine performance and long life, careful attention must be paid to engine oil. Following these simple, but important steps will help protect your investment: . Always use engine oil approved to the proper specification and of the proper viscosity grade. See “Selecting the Right Engine Oil” in this section.


Vehicle Care


10-7


. Check the engine oil level regularly and maintain the proper oil level. See “Checking Engine Oil” and “When to Add Engine Oil” in this section.


. Change the engine oil at the


appropriate time. See Engine Oil Life System on page 10-10. . Always dispose of engine oil


properly. See “What to Do with Used Oil” in this section.


Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the vehicle must be on level ground. The engine oil dipstick handle is a loop. See Engine Compartment Overview on page 10-6 for the location of the engine oil dipstick.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (8,1)


10-8


Vehicle Care


Obtaining an accurate oil level reading is essential: 1.


If the engine has been running recently, turn off the engine and allow several minutes for the oil to drain back into the oil pan. Checking the oil level too soon after engine shutoff will not provide an accurate oil level reading.


{ Warning


The engine oil dipstick handle may be hot; it could burn you. Use a towel or glove to touch the dipstick handle.


2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level.


When to Add Engine Oil


If the oil is below the cross-hatched area at the tip of the dipstick, add 1 L (1 qt) of the recommended oil and then recheck the level. See “Selecting the Right Engine Oil” in this section for an explanation of what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 12-2.


{ Caution


Do not add too much oil. Oil levels above or below the acceptable operating range shown on the dipstick are harmful to the engine. If you find that you


(Continued)


Caution (Continued)


have an oil level above the operating range, i.e., the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. You should drain out the excess oil or limit driving of the vehicle and seek a service professional to remove the excess amount of oil.


See Engine Compartment Overview on page 10-6 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (9,1)


Selecting the Right Engine Oil Selecting the right engine oil depends on both the proper oil specification and viscosity grade. See Recommended Fluids and Lubricants on page 11-12.


Specification Use and ask for licensed engine oils with the dexos1® approved certification mark. Engine oils meeting the requirements for the vehicle should have the dexos1
approved certification mark. This certification mark indicates that the oil has been approved to the dexos1
specification.


{ Caution


Failure to use the recommended engine oil can result in engine damage not covered by the vehicle warranty. Check with your dealer or service provider on whether the oil is approved to the dexos1 specification.


Viscosity Grade SAE 5W-30 is the best viscosity grade for the vehicle. Do not use other viscosity grade oils such as SAE 10W-30, 10W-40, or 20W-50. Cold Temperature Operation: In an area of extreme cold, where the temperature falls below −29°C (−20°F), an SAE 0W-30 oil may be used. An oil of this viscosity grade will provide easier cold starting for the engine at extremely low temperatures. When selecting an oil of the appropriate viscosity grade, always select an oil of the correct


Vehicle Care


10-9


specification. See “Specification” earlier in this section for more information. Engine Oil Additives/Engine Oil Flushes Do not add anything to the oil. The recommended oils with the dexos specification and displaying the dexos certification mark are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (10,1)


10-10


Vehicle Care


containing used engine oil. See the manufacturer's warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the filter before disposal. Never dispose of oil by putting it in the trash or pouring it on the ground, into sewers, or into streams or bodies of water. Recycle it by taking it to a place that collects used oil.


Engine Oil Life System


When to Change Engine Oil This vehicle has a computer system that indicates when to change the engine oil and filter. This is based on a combination of factors which include engine revolutions, engine temperature, and miles driven. Based on driving conditions, the mileage at which an oil change is indicated can vary considerably. For the oil life system to work properly, the system must be reset every time the oil is changed.


When the system has calculated that oil life has been diminished, it indicates that an oil change is necessary. A CHANGE ENGINE OIL SOON message comes on. See Engine Oil Messages on page 5-33. Change the oil as soon as possible within the next 1 000 km (600 mi). It is possible that, if driving under the best conditions, the oil life system might indicate that an oil change is not necessary for up to a year. The engine oil and filter must be changed at least once a year and, at this time, the system must be reset. Your dealer has trained service people who will perform this work and reset the system. It is also important to check the oil regularly over the course of an oil drain interval and keep it at the proper level. If the system is ever reset accidentally, the oil must be changed at 5 000 km (3,000 mi) since the last oil change. Remember to reset the oil life system whenever the oil is changed.


How to Reset the Engine Oil Life System Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change. To reset the system: 1. Turn the ignition key to ON/RUN


with the engine off.


2. Fully press and release the


accelerator pedal slowly three times within five seconds.


3. Turn the key to LOCK/OFF. If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (11,1)


Automatic Transmission Fluid (4-Speed Transmission) If the vehicle has a diesel engine, see the Duramax diesel supplement for more information. When to Check and Change Automatic Transmission Fluid A good time to check the automatic transmission fluid level is when the engine oil is changed. Change the fluid and filter at the intervals listed in Maintenance Schedule on page 11-3 and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 11-12. How to Check Automatic Transmission Fluid Because this operation can be a little difficult, it may be decided to have this done at the dealer.


If not taken to the dealer, be sure to follow all the instructions here or a false reading on the dipstick could result.


{ Caution


Too much or too little fluid can damage the transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the transmission to overheat. Be sure to get an accurate reading if checking the transmission fluid.


Wait at least 30 minutes before checking the transmission fluid level if you have been driving: . When outside temperatures are


above 32°C (90°F).


. At high speed for quite a while. In heavy traffic — especially in hot weather.


Vehicle Care


10-11


. While pulling a trailer. To get the right reading, the fluid should be at normal operating temperature, which is 82°C to 93°C (180°F to 200°F). Get the vehicle warmed up by driving about 24 km (15 mi) when outside temperatures are above 10° C (50°F). If it is colder than 10°C (50°F), drive the vehicle in 3 (Third) until the engine temperature gauge moves and then remains steady for 10 minutes. A cold fluid check can be made after the vehicle has been sitting for eight hours or more with the engine off, but this is used only as a reference. Let the engine run at idle for five minutes if outside temperatures are 10°C (50°F) or more. If it is colder than 10°C (50°F), the engine may have to idle longer. Should the fluid level be low during this cold check, the fluid must be checked hot before adding fluid. Checking the fluid hot will give a more accurate reading of the fluid level.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (12,1)


10-12


Vehicle Care


Checking the Fluid Level Prepare the vehicle as follows: 1. Park the vehicle on a level


place. Keep the engine running. 2. With the parking brake applied, place the shift lever in P (Park).


3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. Then, position the shift lever in P (Park).


4. Let the engine run at idle for


three minutes or more.


Then, without shutting off the engine, use the steps that follow.


The transmission dipstick is near the center of the engine compartment and will be labeled with the graphic shown. See Engine Compartment Overview on page 10-6. 1. Flip the handle up, pull out the


dipstick, and wipe it with a clean rag or paper towel.


2. Push it back in all the way, wait three seconds, then pull it back out again.


3. Check both sides of the dipstick,


and read the lower level. The fluid level must be in the COLD area for a cold check or in the HOT or cross-hatched area for a hot check. Be sure to keep the dipstick pointed down to get an accurate reading.


4.


If the fluid level is in the acceptable range, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place.


How to Add Automatic Transmission Fluid Refer to Recommended Fluids and Lubricants on page 11-12 to determine what kind of transmission fluid to use. Using a funnel, add fluid down the transmission dipstick tube only after checking the transmission fluid while it is hot. A cold check is used only as a reference. If the fluid level is low, add only enough of the proper fluid to bring the level up to the HOT area for a hot check. It does not take much fluid, generally less than 0.5 L (1 pt). Do not overfill.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (13,1)


{ Caution


Use of the incorrect automatic transmission fluid may damage the vehicle, and the damage may not be covered by the vehicle warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 11-12.


. After adding fluid, recheck the fluid level as described under “How to Check Automatic Transmission Fluid,” earlier in this section.


. When the correct fluid level is


obtained, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place.


Automatic Transmission Fluid (6-Speed Transmission)


When to Check and Change Automatic Transmission Fluid It is usually not necessary to check the transmission fluid level. The only reason for fluid loss is a transmission leak or overheated transmission. If a small leak is suspected, use the following procedures to check the fluid level. However, if there is a large leak, it may be necessary to have the vehicle towed to a dealer and have it repaired before driving the vehicle further. Change the fluid and filter at the intervals listed in Maintenance Schedule on page 11-3, and be sure to use the transmission fluid listed in Recommended Fluids and Lubricants on page 11-12.


Vehicle Care


10-13


How to Check Automatic Transmission Fluid Because this operation can be difficult, it is recommended to have this check done at your dealer, which can monitor the transmission temperature. The transmission fluid level increases with temperature. To obtain a highly accurate fluid level check, the transmission temperature must be measured. If it is decided to check the fluid level, be sure to follow all the instructions here, or a false reading on the dipstick may occur. { Caution


Too much or too little fluid can damage the transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the


(Continued)


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (14,1)


10-14


Vehicle Care


Caution (Continued)


transmission to overheat. Be sure to get an accurate reading if checking the transmission fluid.


Wait at least 30 minutes with the engine off, before checking the transmission fluid level if the vehicle has been driven:


In hot weather, when outside temperatures are above 32°C (90°F). The vehicle is heavily loaded.


. At high speed for quite a while in


hot weather. In heavy traffic and hot weather.


. While pulling a trailer. After driving under these conditions, a hot check can be performed. The fluid should be hot, which is 71°C to 93°C (160°F to 200°F).


A cold fluid level check can be performed after the vehicle has been sitting for eight hours or more with the engine off, but this is used only as a reference. Let the engine run at idle for five minutes if the outside temperature is between 15°C to 32°C (60°F to 90°F). Should the fluid level be low during this cold check, the fluid must be checked warm or hot before adding fluid. If the outside temperature is colder than 15°C (60°F) or hotter than 32°C (90°F), a cold check cannot be performed. A warm fluid level check can be performed by driving the vehicle under lightly loaded conditions and outside temperatures between 10°C to 27°C (50°F to 80°F). The vehicle should be driven for at least 24 km (15 mi) before performing a warm check. Checking the fluid warm or hot will give a more accurate reading of the fluid level than a cold check.


Because the vehicle is equipped with a high-efficiency air-to-oil cooler, the transmission fluid temperature may not reach the required hot fluid level checking temperature under normal lightly loaded driving vehicle conditions.


Checking the Fluid Level Prepare the vehicle: 1. Park the vehicle on a level


place. Keep the engine running. 2. With the parking brake applied, place the shift lever in P (Park). 3. With a foot on the brake pedal,


move the shift lever through each gear range, pausing for about three seconds in each range. When M is reached, move the selector from M1
through M3. Then, position the shift lever in P (Park).


4. Let the engine run at idle for


two minutes or more.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (15,1)


Then, without shutting off the engine, use the steps that follow.


The transmission dipstick is near the center of the engine compartment and will be labeled with the graphic shown. See Engine Compartment Overview on page 10-6 for more information on location.


1. COLD Range 2. WARM Range 3. HOT Range


1. Flip the handle up, pull out the


dipstick, and wipe it with a clean rag or paper towel.


2. Push it back in all the way, wait three seconds, and pull it back out again.


3. Check both sides of the dipstick,


and read the lower level. The fluid level must be in the COLD (1) range for a cold check, transmission temperature 27°C to 32°C (80°F to 90°F); between the COLD (1) and HOT (3) range for a WARM (2) check, 50°C to 60°C (122°F to 140°F); or in the HOT (3) cross-hatched range for a hot check, 71°C to 93°C (160°F to 200°F). Be sure to keep the dipstick pointed down to get an accurate reading. If the fluid level is in the acceptable range, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place.


4.


Vehicle Care


10-15


How to Add Automatic Transmission Fluid Refer to Recommended Fluids and Lubricants on page 11-12 to determine what kind of transmission fluid to use.


1. WARM Range 2. HOT Range Using a funnel, add fluid down the transmission dipstick tube only after checking the transmission fluid while it is warm or hot. A cold check is used only as a reference. If the fluid level is low, add only enough of the proper fluid to bring the level up to the middle of the WARM (1) or HOT (2) range depending on the ambient temperature and prior driving conditions. Refer to “How to Check Automatic Transmission


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (16,1)


10-16


Vehicle Care


Fluid” earlier in this section for instructions on driving to achieve warm or hot transmission fluid. It does not take much fluid, generally less than 0.5 L (1 pt). Do not overfill.


{ Caution


Use of the incorrect automatic transmission fluid may damage the vehicle, and the damage may not be covered by the vehicle warranty. Always use the automatic transmission fluid listed in Recommended Fluids and Lubricants on page 11-12.


. After adding fluid, recheck the fluid level as described under “How to Check Automatic Transmission Fluid,” earlier in this section.


. When the correct fluid level is


obtained, push the dipstick back in all the way; then flip the handle down to lock the dipstick in place.


Engine Air Cleaner/Filter


The engine air cleaner/filter is near the center of the engine compartment. See Engine Compartment Overview on page 10-6.


When to Inspect the Engine Air Cleaner/Filter Inspect or replace the air cleaner/ filter at the scheduled maintenance intervals. See Maintenance Schedule on page 11-3. If driving in dusty/dirty conditions, inspect the filter at each engine oil change. How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake it to release loose dust and dirt. If the filter remains covered with dirt, a new filter is required. Never use compressed air to clean the filter. To inspect or replace the engine air cleaner/filter: 1. Unhook the retainer clips and


remove the cover.


2. Lift the filter out of the engine air


cleaner/filter housing. Care should be taken to dislodge as little dirt as possible.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (17,1)


Vehicle Care


10-17


{ Caution


If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place when you are driving.


Cooling System The cooling system allows the engine to maintain the correct working temperature.


3. Clean the engine air cleaner/


4.


filter housing. Inspect or replace the engine air cleaner/filter. Make sure that the filter fits properly into the housing.


5. Reinstall the cover and fasten


the retaining clips.


{ Warning


Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off.


4.3L V6 Engine Shown (4.8L


V8 Engine, 5.3L V8 Engine, and


6.0L V8 Engine Similar)


1. Radiator Pressure Cap 2. Coolant Recovery Tank 3. Engine Cooling Fan (Out


of View)


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (18,1)


10-18


Vehicle Care


{ Warning


An electric engine cooling fan can start even when the engine is not running. To avoid injury, always keep hands, clothing, and tools away from any engine cooling fan.


{ Warning


Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle.


{ Caution Using coolant other than DEX-COOL® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner. Any repairs would not be covered by the vehicle warranty. Always use DEX-COOL (silicate-free) coolant in the vehicle.


Engine Coolant The cooling system in the vehicle is filled with DEX-COOL® engine coolant. This coolant is designed to remain in the vehicle for 5 years or 240 000 km (150,000 mi), whichever occurs first. The following explains the cooling system and how to check and add coolant when it is low. If there is a problem with engine overheating, see Engine Overheating on page 10-22.


What to Use


{ Warning


Adding only plain water or some other liquid to the cooling system can be dangerous. Plain water and other liquids, can boil before the proper coolant mixture will. The coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/ 50 mixture of clean, drinkable water and DEX-COOL coolant.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (19,1)


Use a 50/50 mixture of clean, drinkable water and DEX-COOL coolant. If using this mixture, nothing else needs to be added. This mixture: . Gives freezing protection down


to −37°C (−34°F), outside temperature.


. Gives boiling protection up to


129°C (265°F), engine temperature.


. Protects against rust and


corrosion.


. Will not damage aluminum parts. . Helps keep the proper engine


temperature.


{ Caution


If improper coolant mixture, inhibitors, or additives are used in the vehicle cooling system, the engine could overheat and be damaged. Too much water in the


(Continued)


Caution (Continued)


mixture can freeze and crack engine cooling parts. The repairs would not be covered by the vehicle warranty. Use only the proper mixture of engine coolant for the cooling system. See Recommended Fluids and Lubricants on page 11-12.


Never dispose of engine coolant by putting it in the trash, pouring it on the ground, or into sewers, streams, or bodies of water. Have the coolant changed by an authorized service center, familiar with legal requirements regarding used coolant disposal. This will help protect the environment and your health. Checking Coolant The vehicle must be on a level surface when checking the coolant level.


Vehicle Care


10-19


Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the COLD FILL mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant recovery tank, but be sure the cooling system is cool before this is done.


The coolant recovery tank cap has this symbol on it. When the engine is cold, the coolant level should be at or above the COLD FILL mark. If it is not, there could be a leak in the cooling system.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (20,1)


10-20


Vehicle Care


If the coolant is low, add the coolant or take the vehicle to a dealer for service. How to Add Coolant to the Recovery Tank for Gasoline Engines


{ Warning


You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine.


{ Caution


This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged.


If coolant is needed, add the proper DEX-COOL coolant mixture at the coolant recovery tank. How to Add Coolant to the Radiator


{ Warning


Steam and scalding liquids from a hot cooling system can blow out and burn you badly. Never turn the cap when the cooling system, including the surge tank pressure cap, is hot. Wait for the cooling system and surge tank pressure cap to cool.


If coolant is needed, add the proper mixture directly to the radiator, but be sure the cooling system is cool before this is done.


1. Remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it first stops. Do not press down while turning the pressure cap. If a hiss is heard, wait for that to stop. A hiss means there is still some pressure left.


2. Keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (21,1)


Vehicle Care


10-21


3. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the filler neck. See Recommended Fluids and Lubricants on page 11-12 for more information about the proper coolant mixture.


4. Fill the coolant recovery tank to


6. Start the engine and let it run


the COLD FILL mark.


5. Reinstall the cap back on the


coolant recovery tank, but leave the radiator pressure cap off.


until the upper radiator hose can be felt getting hot. Watch out for the engine cooling fan.


7. By this time, the coolant level inside the radiator filler neck may be lower. If the level is lower, add more of the proper DEX-COOL coolant mixture through the filler neck until the level reaches the base of the filler neck.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (22,1)


10-22


Vehicle Care


8. Replace the pressure cap. At


any time during this procedure if coolant begins to flow out of the filler neck, reinstall the pressure cap.


{ Caution


If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured.


Engine Overheating If the vehicle has a diesel engine, see the Duramax diesel supplement. The vehicle has an indicator to warn of engine overheating. There is an engine coolant temperature gauge on the vehicle's instrument cluster. See Engine Coolant Temperature Gauge on page 5-13.


If the decision is made not to lift the hood when this warning appears, but instead get service help right away, see Roadside Assistance Program on page 13-5. If the decision is made to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, the fan should be running. If it is not, do not continue to run the engine and have the vehicle serviced. See if the engine cooling fan speed increases when idle speed is doubled by pushing the accelerator pedal down. If it does not, the vehicle needs service. Turn off the engine.


{ Caution


Running the engine without coolant may cause damage or a fire. Vehicle damage would not be covered by the vehicle warranty.


If Steam is Coming from the Engine Compartment { Warning


Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood.


(Continued)


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (23,1)


Warning (Continued)


If you keep driving when the engine is overheated, the liquids in it can catch fire. You or others could be badly burned. Stop the engine if it overheats, and get out of the vehicle until the engine is cool.


If No Steam is Coming from the Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day. . Stops after high-speed driving. Idles for long periods in traffic. Tows a trailer. See “Driving on Grades” under Trailer Towing on page 9-51.


If the overheat warning is displayed with no sign of steam: 1. Turn the air off. 2. Turn the heater on to the highest


temperature and to the highest fan speed. Open the windows as necessary.


3. When it is safe to do so, pull off


the road, shift to P (Park) or N (Neutral) and let the engine idle.


If the engine coolant temperature gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slowly for about 10 minutes. Keep a safe vehicle distance from the vehicle in front. If the warning does not come back on, continue to drive normally and have the cooling system checked for proper fit and function. If the warning continues, pull over, stop, and park the vehicle right away.


Vehicle Care


10-23


If there is still no sign of steam, push down the accelerator until the engine speed is about twice as fast as normal idle speed for at least three minutes while parked. If the warning is still on, turn off the engine until it cools down. If the decision is made not to lift the hood, get service help right away.


Engine Fan The vehicle has a clutched engine cooling fan. When the clutch is engaged, the fan spins faster to provide more air to cool the engine. In most everyday driving conditions, the fan is spinning slower and the clutch is not fully engaged. This improves fuel economy and reduces fan noise. Under heavy vehicle loading, trailer towing, and/or high outside temperatures, the fan speed increases as the clutch more fully engages, so an increase in fan noise may be heard. This is normal and should not be mistaken as the transmission slipping or making


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (24,1)


10-24


Vehicle Care


extra shifts. It is merely the cooling system functioning properly. The fan will slow down when additional cooling is not required and the clutch partially disengages. This fan noise may be heard when starting the engine. It will go away as the fan clutch partially disengages.


Power Steering Fluid


The power steering fluid reservoir is in the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 10-6 for reservoir location.


When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless there is a leak suspected in the system or an unusual noise is heard. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering fluid: 1. Turn the key off and let the


engine compartment cool down. 2. Wipe the cap and the top of the


reservoir clean.


3. Unscrew the cap and wipe the


dipstick with a clean rag.


4. Replace the cap and completely


tighten it.


5. Remove the cap again and look at the fluid level on the dipstick.


The level should be at the COLD FILL mark. If necessary, add only enough fluid to bring the level up to the mark. To prevent contamination of brake fluid, never check or fill the power steering reservoir with the brake master cylinder cover off. What to Use


{ Caution


Use of the incorrect fluid may damage the vehicle and the damages may not be covered by the vehicle warranty. Always use the correct fluid listed in Recommended Fluids and Lubricants on page 11-12.


To determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 11-12. Always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (25,1)


Washer Fluid


What to Use When the vehicle needs windshield washer fluid, be sure to read the manufacturer's instructions before use. If operating the vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding Washer Fluid


Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 10-6 for reservoir location.


{ Caution


. Do not use engine coolant


(antifreeze) in the windshield washer. It can damage the windshield washer system and paint.


. Do not mix water with


ready-to-use washer fluid. Water can cause the solution to freeze and damage the washer fluid tank and other parts of the washer system.


. When using concentrated


washer fluid, follow the manufacturer instructions for adding water.


. Fill the washer fluid tank only


three-quarters full when it is very cold. This allows for fluid expansion if freezing occurs, which could damage the tank if it is completely full.


Vehicle Care


10-25


Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time when the vehicle is moving, except when applying the brake pedal firmly.


{ Warning


The brake wear warning sound means that soon the brakes will not work well. That could lead to a crash. When the brake wear warning sound is heard, have the vehicle serviced.


{ Caution


Continuing to drive with worn-out brake pads could result in costly brake repair.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (26,1)


10-26


Vehicle Care


Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications. See Capacities and Specifications on page 12-2. Brake pads should be replaced as complete sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every time the brakes are applied, with or without the vehicle moving, the brakes adjust for wear.


Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced, be sure to get new, approved replacement parts. If this is not done, the brakes might not work properly. For example, installing disc brake pads that are wrong for the vehicle, can change the balance between the front and rear brakes — for the worse. The braking performance expected can change in many other ways if the wrong replacement brake parts are installed.


Brake Fluid


The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 10-6 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down:


The brake fluid level goes down because of normal brake lining wear. When new linings are installed, the fluid level goes back up.


. A fluid leak in the brake


hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (27,1)


Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary, only when work is done on the brake hydraulic system.


{ Warning


Refer to the Maintenance Schedule to determine when to check the brake fluid. See Maintenance Schedule on page 11-3. Checking Brake Fluid Check brake fluid by looking at the brake fluid reservoir. See Engine Compartment Overview on page 10-6.


If too much brake fluid is added, it can spill on the engine and/or fuel operated heater parts, if equipped. If the vehicle has a diesel engine and a fuel operated heater, see “Fuel Operated Heater (FOH)” in the diesel engine supplement. The fluid will burn if the engine is hot enough. You or others could be burned, and the vehicle could be damaged. Add brake fluid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section.


The fluid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak.


Vehicle Care


10-27


After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.


What to Add Use only new DOT 3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 11-12. Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.


{ Warning


With the wrong kind of fluid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake fluid.


Chevrolet Express Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 6014662) - 2014 - crc - 8/26/13


Black plate (28,1)


10-28


Vehicle Care


{ Caution


. Using the wrong fluid can


badly damage brake hydraulic system parts. For

Loading...
x