Download PDF Manual

113


Vehicle Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another. Some messages may not require immediate action, but you can press SET/CLR to acknowledge that you received the messages and to clear them from the display. Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem. You will find the possible messages that can be displayed and some information about them grouped by subject in the following information.


Battery Voltage and Charging Messages


BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery - North America 0 218
SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


114


Instruments and Controls


Brake System Messages


Cruise Control Messages


BRAKE FLUID LOW This message is displayed when the brake fluid level is low; see Brake Fluid 0 217
RELEASE PARKING BRAKE This message is displayed as a reminder that the parking brake is on. Release it before you attempt to drive.


ii


Compass Messages


CAL This message is displayed when the compass needs to be calibrated. See Compass 0 95
– – Dashes will be displayed if the compass needs service. See your dealer for service.


ii


APPLY BRAKE BEFORE CRUISE If this message displays when attempting to activate cruise control, apply the brake pedal and try again. CRUISE SET TO XXX This message displays when the cruise control is set and shows the speed it was set to. See Cruise Control 0 174


ii


Door Ajar Messages


DOOR OPEN A door open symbol will be displayed on the DIC showing which door is open. If the vehicle has been shifted out of P (Park), a DOOR OPEN message will also be displayed. Close the door completely.


MANUALLY CLOSE THE POWER LIFTGATE This message will display if the power liftgate encounters multiple obstacles on the same power cycle. After removing the obstructions, the liftgate will resume normal power operation. REAR ACCESS OPEN This message will display along with a symbol when the liftgate is open. Close the liftgate completely.


Engine Cooling System Messages


A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Instruments and Controls


115


ii


conditioning compressor turns back on. The vehicle can continue to be driven. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine. COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant 0 210
ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid


severe damage. This message clears when the engine has cooled to a safe operating temperature. HIGH COOLANT TEMPERATURE This message may display if the coolant temperature is hot. See Engine Overheating 0 214


ii


Engine Oil Messages


CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the oil life system. See Engine Oil Life System 0 207
Driver Information Center (DIC) , and 0 110
Maintenance Schedule 0 273
ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.


, Engine Oil 0 204


ii


ii


ii


ii


ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil 0 204
OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.


ii


Engine Power Messages


ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


116


Instruments and Controls


to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.


Fuel System Messages


Key and Lock Messages


REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced.


Object Detection System Messages


ii


ECO MODE ON On some models, this message displays when the Fuel Economy Mode has been turned on by pressing the eco button near the shift lever. See Fuel Economy Mode 0 169
FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible. TIGHTEN GAS CAP This message may display when the fuel cap is not on tight. Tighten the fuel cap.


FORWARD COLLISION ALERT OFF If your vehicle has the Forward Collision Alert (FCA) system, this message may display if the FCA system cannot activate due to a temporary condition. See Forward Collision Alert (FCA) System 0 180
FRONT CAMERA BLOCKED, CLEAN WINDSHIELD This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled because the camera view is blocked and cannot operate properly. It may also


ii


activate during heavy rain or due to road spray. To clean the system, clean the outside of the windshield area in front of the LDW/FCA camera sensor. LANE DEPARTURE SYSTEM UNAVAILABLE If your vehicle has the Lane Departure Warning (LDW) system, this message may display if the LDW system cannot activate due to a temporary condition. See Lane Departure Warning (LDW) 0 184
more information. PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary condition causing the system to be disabled. See Parking Assist 0 178
SERVICE SIDE DETECTION SYSTEM If this message appears, both SBZA displays will remain on indicating there is a problem with the SBZA system. If these displays remain on


for


ii


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


after continued driving, the system needs service. Take the vehicle to your dealer. SERVICE FRONT CAMERA This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled and need service. See your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Rear Parking Assist (RPA) system. Do not use this system to help you park. See Parking Assist 0 178
SIDE BLIND ZONE ALERT SYSTEM OFF This message indicates that the driver has turned the system off. SIDE BLIND ZONE SYS. UNAVAILABLE This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone. The sensor may be blocked by mud,


ii


Instruments and Controls


117


dirt, snow, ice, or slush. This message may also activate during heavy rain or due to road spray. The vehicle does not need service. For cleaning, see Side Blind Zone Alert (SBZA) 0 182


ii


Ride Control System Messages


ALL WHEEL DRIVE OFF If your vehicle has the All-Wheel Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in two-wheel drive. This could be caused by: . A compact spare tire on the


vehicle.


. AWD system overheat. . Loss of wheel or vehicle speed. . Certain other vehicle electrical


conditions.


This message turns off when the compact spare tire is replaced by a full-size tire, the differential fluid cools or the above conditions are no


longer present and the warning message is reset. To reset the warning message manually, turn the ignition off and then back on again after 30 seconds. If the message stays on, see your dealer. SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel Drive (AWD) system. The vehicle will run in two-wheel drive. This could be caused by: . An electronics problem. . Worn out or overheated clutch


plates.


. Various electrical issues. If this message appears, stop as soon as possible and turn off the ignition for 30 seconds. Restart the vehicle and check for the message on the DIC display. If the message still displays or appears again when you begin driving, the system needs service. See your dealer right away.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


118


Instruments and Controls


ii


SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control/Electronic Stability Control 0 172
SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. See Traction Control/Electronic Stability Control 0 172
STABILITRAK OFF This message displays when the StabiliTrak system is turned off. See Traction Control/Electronic Stability Control 0 172
TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly.


ii


ii


TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is first turned on. See Traction Control/ Electronic Stability Control 0 172


ii


Airbag System Messages


SERVICE AIRBAG This message displays if there is a problem with the airbag system. See your dealer for service.


Security Messages


THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.


Service Vehicle Messages


SERVICE POWER STEERING This message displays and a chime may sound when there may be a problem with the power steering system. If this message displays and a reduction in steering


performance or loss of power steering assistance is noticed, see your dealer. SERVICE VEHICLE SOON This message is displayed if there is a problem with the vehicle. Take the vehicle to your dealer for service.


Tire Messages


ii


SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation 0 239
TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation 0 239
TIRE PRESSURE LOW ADD AIR TO TIRE This message displays when the pressure in one or more of the tires is low.


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Instruments and Controls


119


ii


This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light 0 107
If a tire pressure message appears on the DIC, stop as soon as possible. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires 0 229
and Tire Pressure 0 237
More than one tire pressure message can appear at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) 0 110


, Vehicle Load Limits 0 156


ii


ii


ii


ii


Transmission Messages


SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer.


TURN WIPER CONTROL TO INTERMITTENT FIRST This message is displayed when attempting to adjust the intermittent wiper speed without intermittent selected on the wiper control. See Windshield Wiper/Washer 0 93


ii


SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.


Vehicle Reminder Messages


ICE POSSIBLE DRIVE WITH CARE This message is displayed when ice conditions are possible.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


120


Instruments and Controls


Vehicle Personalization Use the audio system controls to access the personalization menus for customizing vehicle features. The following are all possible personalization features. Depending on the vehicle, some may not be available.


Infotainment System Audio System Controls


Using the Faceplate MENU/SELECT Knob . Press to enter, select, or activate


a highlighted menu option.


. Turn to highlight a menu option. . Press to enable or disable a


system setting.


E BACK . Press to exit a menu. . Press to return to a previous


screen.


Using the Touchscreen Touch a screen feature to: . View more feature options. . Enable or disable the feature. w : Touch to scroll up. x : Touch to scroll down. Back : Touch to return to the previous menu. To access the personalization menu: 1. Touch Config on the Home


page on the infotainment system display or press CONFIG on the faceplate.


2. Select the desired feature to


display a list of available options.


3. Select the desired feature


setting.


Personalization Menus The following list of menu items may be available: . Languages . Time and Date


. Radio Settings . Phone Settings . Navigation Settings . Display Settings . Vehicle Settings Each menu is detailed in the following information. Languages Select Language, then select from the available language(s). Time and Date Manually set the time and date. See Clock 0 95
Radio Settings Select and depending on the radio the following may display: . Auto Volume . Gracenote Options . XM Channel Art . Max Startup Volume . Number of Favorites Pages . RDS Options


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Instruments and Controls


121


. XM Categories . Software Versions Menu


Auto Volume This feature adjusts the volume to minimize the effects of unwanted background noise that can result from changing road surfaces, driving speeds, or open windows. This feature works best at lower volume settings where background noise is typically louder than the sound system volume. Select Off, Low, Medium, or High.


Gracenote Options Select and the following may display: . Normalization


XM Channel Art This feature turns the XM Audio page background on the XM Channel display on and off. Select to enable or disable.


Max Startup Volume This feature sets the maximum startup volume. If the vehicle is started and the volume is greater than this level, the volume is adjusted to this level. Select + or − to increase or decrease the volume.


Number of Favorite Pages Select to set the number of favorites to display. Select the desired number.


Normalization This feature improves voice recognition and media groupings. See “USB,” “Auxiliary Devices,” and “Bluetooth Audio” in the infotainment manual. Select to enable or disable.


RDS Options Select and the following may display: . RDS . Text Scroll Freeze . RDS Text


RDS Select to turn RDS on or off. See “Radio Data System (RDS)” in the infotainment manual.


Text Scroll Freeze When on, this allows the RDS Text to scroll across the radio screen. Select to enable or disable.


RDS Text When on, this allows the RDS information from the station to be displayed. Select to enable or disable.


XM Categories This allows which available XM Categories are used and displayed. Select to enable or disable available categories.


Software Versions Menu Select to display information about the system and update software if available.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


122


Instruments and Controls


Phone Settings Select and the following may display: . Bluetooth . Sort Order


Bluetooth Select and the following may display: . Device List . Pair Device . Pair Device (Phone) . Pair Device (GPS)


Device List Select to connect to a different phone source, disconnect a phone, or delete a phone.


Pair Device Select to pair a new device. See “Pairing a Phone/Device” under “Bluetooth” in the infotainment manual.


Pair Device (Phone) or Pair Device (GPS) Select to pair a new phone. See “Pairing a Phone/Device” under “Bluetooth” in the infotainment manual.


Sort Order Select to change the sort order of the contact list. See “Phone Settings” under “Bluetooth” in the infotainment manual. Select First Name Last or Last Name First. Navigation Settings See “Navigation Settings” under “Configure Menu” in the infotainment manual. Display Settings Select and the following may display: . Home Page Menu . Rear Camera Options . Display Off . Map Settings


Home Page Menu Select and the following may display: . Customize . Sort . Restore Home Page Defaults


Customize This feature allows the selection of what icons will be on the first Home Page. Select and follow the screen prompts.


Sort This feature allows the icons on the Home Page to be moved. Select and follow the screen prompts.


Restore Home Page Defaults This feature will restore the Home Page to the factory settings. Select and follow the screen prompts.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Rear Camera Options Select and the following may display: . Symbols . Guide Lines . Rear Cross Traffic Alert (RCTA)


Symbols When enabled, symbols will show on the camera screen. See Rear Vision Camera (RVC) 0 176
Select to enable or disable.


ii


Guide Lines When enabled, guide lines will show on the camera screen. See Rear Vision Camera (RVC) 0 176
Select to enable or disable.


ii


Rear Cross Traffic Alert (RCTA) When enabled, a symbol will show on the camera screen to warn of traffic coming from either direction. See Rear Vision Camera (RVC) 0 176
Select to enable or disable.


ii


Instruments and Controls


123


Display Off Select to turn the display off. The display will return when any radio buttons are pressed or the screen is touched (if equipped). Map Settings Select and the following may display: . Map Display . Speed Limits


Map Display This feature changes the map screen display. See “Map Settings” under “Configure Menu” in the infotainment manual. Select Automatic, Day, or Night.


Speed Limits When enabled, the current road speed limit will display on the map. See “Map Settings” under “Configure Menu” in the infotainment manual. Select to enable or disable.


Vehicle Settings Select and the following may display: . Climate and Air Quality . Comfort and Convenience . Collision Detection Systems . Lighting . Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings? Climate and Air Quality Select and the following may display: . Auto Fan Speed . Air Conditioning Mode . Remote Start Auto Heat Seats . Auto Defog . Auto Rear Defog


Auto Fan Speed This selection is available on vehicles with the Automatic Climate Control System. Choose the blower speed settings.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


124


Instruments and Controls


Select High, Medium, or Low


Air Conditioning Mode This will allow you to select whether or not the air conditioning comes on automatically the next time the vehicle is started. On means that the air conditioning will be on at start up, regardless of whether it was on or off the last time the vehicle was turned off. Off means the air conditioning will be off at the next start up, regardless of whether it was on or off the last time the vehicle was turned off. Last Setting means that when the vehicle is started, the air conditioning will resume whichever setting it was at the last time the vehicle was turned off. Select On, Off, or Last Setting.


Remote Start Auto Heat Seats When on, this feature will turn the heated seats on when using remote start on cold days. Select to enable or disable.


Auto Defog When turned on and high humidity is detected, the climate control system may adjust to outside air supply and turn on the air conditioner or the heater. The fan speed may slightly increase to help prevent fogging. When high humidity is no longer detected, the system will return to its prior operation. Select On or Off.


Auto Rear Defog When on, this feature turns on the rear defogger at vehicle start when the interior temperature is cold and fog is likely. The auto rear defog function can be disabled by pressing 1. When off, the feature can be turned on by pressing 1. See “Rear Window Defogger” under or Climate Control Systems 0 137
Automatic Climate Control System 0 139
Select On or Off.


ii


ii


Comfort and Convenience Select and the following may display: . Easy Exit Driver Seat . Chime Volume . Reverse Tilt Mirror . Memory Remote Recall . Button Chime


Easy Exit Driver Seat This feature moves the seat rearward allowing the driver more room to exit the vehicle. See “Easy Exit Driver Seat” under Memory Seats 0 48
Select On or Off.


ii


Chime Volume This allows the selection of the chime volume level. Select Low or High.


Reverse Tilt Mirror When on, both the driver and passenger mirrors will tilt downward when the vehicle is shifted to R (Reverse) to improve visibility of


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


the ground near the rear wheels. They will return to their previous driving position when the vehicle is shifted out of R (Reverse), the ignition is turned to OFF, or the vehicle is left in R (Reverse). See Reverse Tilt Mirrors 0 38
Select On or Off.


ii


Memory Remote Recall This feature automatically recalls the current driver’s previously stored 1 or 2 button positions when entering the vehicle. See "Recalling RKE Memory Positions (Memory Remote Recall)" under Memory Seats 0 48
Select On or Off.


ii


Button Chime When enabled, a sound will be heard when a selection is made using the infotainment system. Select to enable or disable. Collision Detection Systems Select and the following may display: . Park Assist


Instruments and Controls


125


Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. Select to enable or disable.


Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Select Off, 30 Seconds, 1 Minute, or 2 Minutes. Power Door Locks Select and depending on the radio the following may display: . Auto Door Unlock . Delayed Door Lock


Auto Door Unlock This allows selection of which doors will automatically unlock when the vehicle is shifted into P (Park). Select All Doors, Driver Door, or Off.


. Side Blind Zone Alert . Rear Cross Traffic Alert


Park Assist This allows the Parking Assist feature to be turned on or off. Select On, Off, or On with Tow Bar Attached.


Side Blind Zone Alert (SBZA) This allows the SBZA feature to be turned on or off. See Side Blind Zone Alert (SBZA) 0 182
Select On or Off.


ii


Rear Cross Traffic Alert This allows the Rear Cross Traffic Alert feature to be turned on or off. Select On or Off. See Rear Vision Camera (RVC) 0 176
Lighting Select and the following may display: . Vehicle Locator Lights . Exit Lighting


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


126


Instruments and Controls


ii


Delayed Door Lock When on, this feature will delay the locking of the doors. See Delayed Locking 0 30
Select to enable or disable. Remote Lock/Unlock/Start Select and depending on the radio the following may display: . Remote Unlock Feedback . Remote Unlock Light Feedback . Remote Lock Feedback . Remote Door Unlock


Remote Unlock Feedback or Remote Unlock Light Feedback When on, the exterior lamps will flash when unlocking the vehicle with the RKE transmitter. Depending on the radio select Flash Lights or Off, or select to enable or disable.


Remote Lock Feedback This allows selection of what feedback is provided when unlocking the vehicle with the RKE transmitter.


Select Lights and Horn, Lights Only, Horn Only, or Off.


Remote Door Unlock This allows selection of which doors will unlock on the first press of K on the RKE transmitter. Select Driver Door or All Doors. If Driver Door is selected, all doors will unlock on the second press of K within five seconds of the prior press. Return to Factory Settings? This returns all of the vehicle personalization settings to the factory settings. Select Yes or No.


Universal Remote System See Radio Frequency Statement 0 299


ii


Universal Remote System Programming


If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices. Do not use the Universal Remote system with any garage door opener that does not have the stop and


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Instruments and Controls


127


reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door. Make sure the hand-held transmitter has a new battery for quick and accurate transmission of the radio-frequency signal.


Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held transmitter about 3 to 8 cm (1
to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.


2. At the same time, press and


hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until


the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2 with the procedure under “Radio Signals for Canada and Some Gate Operators” later in this section.


3. Press and hold the newly


programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.


If the indicator light stays on continuously or the garage door moves when the button is pressed, then programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


128


Instruments and Controls


for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.


Learn or Smart Button


4. After completing Steps 1–3,


locate the Learn or Smart button inside the garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.


5. Press and release the Learn or


6.


Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds and then release it. If the garage door does not move or the lamp on the garage door opener receiver does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.


The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons.


Radio Signals for Canada and Some Gate Operators For questions or programming help call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Instruments and Controls


129


Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the


buttons. Do not release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”


Universal Remote System Operation


Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.


2. Release both buttons.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Lighting


130
Lighting


Exterior Lighting


Exterior Lighting


Exterior Lamp Controls


Exterior Lamp Controls . . . . . . . 130
Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . 130
Flash-to-Pass . . . . . . . . . . . . . . . . 131
Daytime Running


Lamps (DRL) . . . . . . . . . . . . . . . 131


Automatic Headlamp


System . . . . . . . . . . . . . . . . . . . . . . 131
Hazard Warning Flashers . . . . . 132
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 132
Fog Lamps . . . . . . . . . . . . . . . . . . . 133


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 133
Dome Lamps . . . . . . . . . . . . . . . . . 133
Reading Lamps . . . . . . . . . . . . . . 134


Lighting Features


Entry Lighting . . . . . . . . . . . . . . . . 134
Exit Lighting . . . . . . . . . . . . . . . . . . 134
Battery Load Management . . . 134


The exterior lamp control is on the turn signal lever. There are four positions. O (Exterior Lamp Control) : Operates the exterior lamps. Turn to one of the following positions: O (Off) : Briefly turn to this position to turn the automatic light control off or on again. AUTO (Automatic Headlamps) : Turns the exterior lamps on and off automatically depending on the exterior light. The vehicle will default to the AUTO setting when it is first started.


; (Parking Lamps) : Turns on the parking lamps including all lamps, except the headlamps. 5 (Headlamps) : Turns on the headlamps, together with the parking lamps and instrument panel lights.


Headlamp High/ Low-Beam Changer 2 3 Headlamp High/Low-Beam Changer : Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.


This indicator light turns on in the instrument cluster when the high-beam headlamps are on.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Flash-to-Pass The flash-to-pass feature works with the low beams or Daytime Running Lamps (DRL) on or off. To flash the high beams, pull the turn signal lever all the way toward you, then release it.


Daytime Running Lamps (DRL) DRL can make it easier for others to see the front of your vehicle during the day. The low-beam headlamps or dedicated DRL, if equipped, come on at a reduced brightness in daylight when the following conditions are met: . The ignition is on. . The exterior lamp control is


in AUTO.


. The transmission is not in


P (Park).


. The light sensor determines it is


daytime.


. The parking brake is released.


Fully functional DRL are required on all vehicles first sold in Canada. When the DRL are on, the taillamps, sidemarker, instrument panel lights, and other lamps will not be on. The instrument cluster will be lit. When the exterior lamp control is turned to 5, the low-beam headlamps come on. The other lamps that come on with the headlamps will also come on. To idle your vehicle with the DRL off, move the shift lever to P (Park). The DRL will stay off until the shift lever is moved out of the P (Park) position. For vehicles first sold in the United States or Mexico, the DRL can also be turned off by turning the lamp control counterclockwise. The DRL will stay off until the next ignition cycle. The regular headlamp system should be turned on when needed.


Lighting


131


Automatic Headlamp System When it is dark enough outside, the headlamps come on automatically.


Do not cover the light sensor on top of the instrument panel or the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel. If the vehicle is started in a dark garage, the automatic headlamp system comes on immediately. If it is light outside when the vehicle leaves the garage, there is a slight delay before the automatic headlamp system changes to the


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


132


Lighting


ii


DRL. During that delay, the instrument cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Illumination Control 0 133
Lights On with Wipers If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are not operating, these lamps turn off. Move the exterior lamp control to P or ; to disable this feature.


Hazard Warning Flashers


Turn and Lane-Change Signals


| (Hazard Warning Flasher) : Press to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off.


Move the lever all the way up or down to signal a turn. An arrow on the instrument cluster will flash in the direction of the turn or lane change. Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is complete. If the lever is briefly pressed and released, the turn signal flashes three times. The lever returns to its starting position when it is released. If after signaling a turn or a lane change the arrows flash rapidly or do not come on, a signal bulb may be burned out.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Have any burned out bulbs replaced. If a bulb is not burned out, check the fuse; see Fuses 0 224


ii


Fog Lamps


For vehicles with fog lamps, the control is located on the turn signal lever. Use the fog lamps for better vision in foggy or misty conditions.


# FOG (Fog Lamps) : Turn the fog lamp band on the lever to # and release it, to turn the fog lamps on or off. The band will return to its original position. The parking lamps or low-beam headlamps must be on to use the fog lamps. The fog lamps will go off whenever the high-beam headlamps are turned on. When the high-beam headlamps are turned off, the fog lamps will come on again. Some localities have laws that require the headlamps to be on along with the fog lamps.


Lighting


133


Interior Lighting


Instrument Panel Illumination Control This control is located on the instrument panel, to the left of the steering column. D (Instrument Panel Brightness) : Turn clockwise or counterclockwise to brighten or dim the lights.


Dome Lamps There are front and rear dome lamps. The dome lamp controls are located in the overhead console. To change the settings, press the following: * (Dome Lamp Override) : Turns the lamps off, even when a door is open. 1 (Door) : The lamps come on automatically when a door is opened. + (On) : Turns the dome lamps on.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


134


Lighting


The dome lamps can also be turned on and off by pressing the buttons next to the lamps.


Reading Lamps The reading lamps are located on the overhead console. These lamps come on automatically when any door is opened. For manual operation, press the button next to each lamp to turn it on or off.


Lighting Features


Entry Lighting The dome lamp, cargo lamp, and foot lamp inside the vehicle come on when any door is opened, if the dome lamp is in the door position. In addition, these lamps come on when the Remote Keyless Entry (RKE) unlock button is pressed. They stay on for 20 seconds or until a door is opened. After the door is opened and then closed, the light remains on for 20 seconds, or until the ignition is turned to ON/RUN. This feature can be changed. See “Vehicle Locator Lights” under Vehicle Personalization 0 120


ii


Exit Lighting Some exterior lamps and interior lamps come on at night, or in areas with limited lighting, when the key is removed from the ignition. The dome lamp comes on after the ignition is changed to the OFF position. The exterior lamps and


dome lamp remain on for a set amount of time, then automatically turn off. The exterior lamps turn off immediately by turning the exterior lamp control off. This feature can be changed. See Vehicle Personalization 0 120


ii


Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery's temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery's state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gauge or a voltage display on the Driver Information Center (DIC), you may see the


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Lighting


135


Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a DIC message might be displayed and it is recommended that the driver reduce the electrical loads as much as possible. See Battery Voltage and Charging Messages 0 113


ii


voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all of the power needed for very high electrical loads. A high electrical load occurs when several of the following are on, such as: headlamps, high beams, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator's output and the vehicle's electrical needs. It can increase engine idle speed to generate more power whenever needed. It can temporarily reduce the power demands of some accessories.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Infotainment System


136
Infotainment System


Introduction


Infotainment . . . . . . . . . . . . . . . . . . 136


Introduction


Infotainment See the infotainment manual for information on the radio, audio players, phone, navigation system, and voice or speech recognition. It also includes information on settings.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Climate Controls


Climate Control Systems


Climate Controls


137


The vehicle's heating, cooling, defrosting, and ventilation can be controlled with this system.


Climate Control Systems


Climate Control Systems . . . . . 137
Automatic Climate Control


System . . . . . . . . . . . . . . . . . . . . . . 139


Air Vents


Air Vents . . . . . . . . . . . . . . . . . . . . . 142


Maintenance


Passenger Compartment Air


Filter . . . . . . . . . . . . . . . . . . . . . . . . 143


1. Fan Control 2. Air Delivery Mode Controls 3. Temperature Control 4. A/C (Air Conditioning) 5. Recirculation 6. Rear Window Defogger 7. Front Defrost 8. Outside Air


A (Fan Control) : Turn to increase or decrease the fan speed. Turn the knob all the way counterclockwise to turn the fan off. Temperature Control : Turn to increase or decrease the temperature.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


138


Climate Controls


Air Delivery Mode Control : To change the current mode, select one of the following: F (Vent) : Air is directed to the instrument panel outlets. * (Bi-Level) : Air is directed to the instrument panel outlets and the floor outlets. 7 (Floor) : Air is directed to the floor outlets with some air directed to the windshield and the side window outlets. W (Defog) : Clears the windows of fog or moisture. Air is directed to the windshield with some air directed to the floor and side window outlets. 0 FRONT (Front Defrost) : Press to clear the windshield of fog or frost more quickly. Air is directed to the windshield and side window outlets. The system allows outside air into the vehicle and the air conditioning compressor will run, unless the outside temperature is below freezing. For best results, clear all snow and ice from the windshield before defrosting.


ii


Do not drive the vehicle until all the windows are clear. If equipped with the Fuel Economy Mode, the climate controls may take longer to heat or cool the cabin and the rear window defogger will turn off sooner, when this feature is in use. See Fuel Economy Mode 0 169
Air Conditioning A/C (Air Conditioning) : Press to turn the air conditioning on or off. An indicator light comes on to show that the air conditioning is enabled. If the fan is turned off, the air conditioner will not run. The A/C light will stay on even if the outside temperature is below freezing. h (Recirculation) : Press to turn on the recirculation. An indicator light comes on. Air is recirculated inside the vehicle. It helps to quickly cool the air inside the vehicle and reduce the outside air and odor that might enter. The air conditioning may come on under certain conditions.


To improve fuel efficiency and to cool the vehicle faster, recirculation may be automatically selected in warm weather. The recirculation light will not come on. To override this feature, select outside air. % (Outside Air) : Press to turn on the outside air. An indicator light comes on. Outside air is circulated throughout the vehicle. Rear Window Defogger 1 REAR (Rear Defogger) : Press to turn the rear window defogger on or off. An indicator light on the button comes on to show that the rear window defogger is on. It turns off if the ignition is put in the ACC/ ACCESSORY or LOCK/OFF position. The ignition must be on to use the rear window defogger. Do not drive the vehicle until all the windows are clear.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Climate Controls


139


Automatic Climate Control System


The vehicle's heating, cooling, defrosting, and ventilation can be controlled with this system.


Caution


Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by the vehicle warranty.


1. Fan Control 2. AUTO (Automatic Operation) 3. Air Delivery Mode Controls 4. Front Defrost 5. Recirculation 6. Temperature Control 7. A/C (Air Conditioning) 8. Driver and Passenger Heated


Seats (If Equipped)


9. Rear Window Defogger 10. Power


Automatic Operation The system automatically controls the fan speed, air delivery, air conditioning, and recirculation to heat or cool the vehicle to the selected temperature. When the AUTO indicator light is on, the system is in full automatic operation.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


140


Climate Controls


To place the system in automatic mode: 1. Press AUTO. 2. Set the temperature to 22° C (72° F) and allow the system time to stabilize. Then adjust the temperature as needed. To improve fuel efficiency and to cool the vehicle faster, recirculation may be automatically selected in warm weather. The recirculation light will not come on. Press h to select recirculation; press it again to select outside air.


Manual Operation O (Power) : Press to turn the climate control system on or off. A (Fan Control) : Turn to increase or decrease the fan speed. Adjusting the fan speed while in automatic mode places the fan under manual control. The AUTO indicator light turns off. The air delivery mode remains in automatic control.


Temperature Control : Turn to increase or decrease the temperature inside the vehicle. H / G (Air Delivery Mode Control) : Press mode up or mode down to cycle through the different air delivery modes. The current mode is shown on the display. Select from the following: F (Vent) : Air is directed to the instrument panel outlets. * (Bi-Level) : Air is directed to the instrument panel outlets and the floor outlets. 7 (Floor) : Air is directed to the floor outlets with some air directed to the windshield and the side window outlets. W (Defog) : Clears the windows of fog or moisture. Air is directed to the windshield with some air directed to the floor and side window outlets. 0 FRONT (Front Defrost) : Press to clear the windshield of fog or frost more quickly. Air is directed to the windshield and side window outlets. The system allows outside air into the vehicle and the air conditioning


compressor will run, unless the outside temperature is below freezing. For best results, clear all snow and ice from the windshield before defrosting. Do not drive the vehicle until all the windows are clear. For vehicles with Fuel Economy Mode, the climate controls may take longer to heat or cool the cabin and the rear window defogger will turn off sooner, when this feature is in use. See Fuel Economy Mode 0 169
Air Conditioning A/C (Air Conditioning) : Press to turn the air conditioning on or off. An indicator light comes on to show that the air conditioning is enabled. If the fan is turned off, the air conditioner will not run. The A/C indicator light will stay on even if the outside temperature is below freezing.


ii


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Climate Controls


141


h (Recirculation) : Press to turn on the recirculation. Press to alternate between recirculation and outside air, if the vehicle does not have a separate outside air button. The indicator light turns on when recirculation is selected. Air is recirculated inside the vehicle. It helps to quickly cool the air inside the vehicle and reduce the outside air and odors that might enter. % (Outside Air, If Equipped) : Press to turn on the outside air. An indicator light comes on. Outside air is circulated throughout the vehicle. Auto Defog : The climate control system has a sensor to automatically detect high humidity inside the vehicle. When high humidity is detected, the climate control system may adjust to outside air supply and turn on the air conditioner. If the climate control system does not detect possible window fogging, it returns to normal operation. To turn Auto Defog on or off, see “Climate and Air Quality” under Vehicle Personalization 0 120


ii


Rear Window Defogger 1 REAR (Rear Defogger) : Press to turn the rear window defogger on or off. An indicator light on the button comes on to show that the rear window defogger is on. It turns off if the ignition is put in the ACC/ ACCESSORY or LOCK/OFF position. The ignition must be on to use the rear window defogger. Do not drive the vehicle until all the windows are clear.


Caution


Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by the vehicle warranty.


ii


z / J (Driver and Passenger Heated Seats) : If equipped with heated seats, see Heated Front Seats 0 50
Remote Start Climate Control Operation : If equipped with the remote start feature, the climate control system may run when the vehicle is started remotely. The system uses the driver’s previous settings to heat or cool the inside of the vehicle. The rear defog may come on during remote start based on cold ambient conditions. The rear defog indicator light does not come on during a remote start. If the vehicle has heated front seats, they may come on during a remote start. See Remote Vehicle Start 0 28
and Heated Front Seats 0 50


ii


ii


Check with your dealer before adding equipment to the outside of the vehicle.


. Do not attach any devices to the


air vent slats. This restricts airflow and may cause damage to the air vents.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


142


Climate Controls


Sensors The solar sensor, located on top of the instrument panel near the windshield, monitors the solar heat. The climate control system uses the information to adjust the temperature, fan speed, recirculation, and air delivery mode. Do not cover the solar sensor or the system will not work properly.


Air Vents


Center Air Vents Use the louvers located on the air vents to change the direction of the airflow. Use the thumbwheels to open or close off the airflow.


Side Air Vents Use the louvers located on the air vents to change the direction of the airflow or to open or close off the airflow.


Operation Tips . Clear away any ice, snow,


or leaves from air inlets at the base of the windshield that could block the flow of air into the vehicle.


. Keep the path under the front seats clear of objects to help circulate the air inside of the vehicle more effectively.


. Use of non-GM approved hood deflectors can adversely affect the performance of the system.


Chevrolet Equinox Owner Manual (GMNA-Localizing-U.S./Canada/Mexico- 9234773) - 2016 - crc - 9/3/15


Maintenance


Climate Controls


143


Passenger Compartment Air Filter The filter reduces the dust, pollen, and other airborne irritants from outside air that is pulled into the vehicle. The filter should be replaced as part of routine scheduled maintenance. See Maintenance Schedule 0 273
for replacement intervals. To find out what type of filter to use, see Maintenance Replacement Parts 0 283
The passenger compartment air filter can be accessed by removing the entire glove box. 1. Open the glove box completely and locate the stop tab on top of the glove box door.


ii


ii


2. Push the stop tab upward until


Loading...
x