2008 Cadillac XLR Owners Manual

Download PDF Manual
On an otherwise clear road, ice patches can appear in shaded areas where the sun cannot reach, such as around clumps of trees, behind buildings, or under bridges. Sometimes the surface of a curve or an overpass can remain icy when the surrounding roads are clear. If you see a patch of ice ahead of you, brake before you are on it. Try not to brake while you are actually on the ice, and avoid sudden steering maneuvers. If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: Turn on the hazard warning ﬂashers. Tie a red cloth to your vehicle to alert police that you have been stopped by the snow. (cid:129) Put on extra clothing or wrap a blanket around you. If you do not have blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats — anything you can wrap around yourself or tuck under your clothing to keep warm. 5-19 (cid:129) (cid:129) {CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. And check around again from time to time to be sure snow does not collect there. Open a window just a little on the side of the vehicle that is away from the wind. This will help keep CO out. You can run the engine to keep warm, but be careful. 5-20 Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the battery charged. You will need a well-charged battery to restart the vehicle, and possibly for signaling later on with the headlamps. Let the heater run for a while. Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes. If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free your vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 5-22. If your vehicle has a traction system, it can often help to free a stuck vehicle. Refer to your vehicle’s traction system in the Index. If the stuck condition is too severe for the traction system to free the vehicle, turn the traction system off and use the rocking method. {CAUTION: If you let your vehicle’s tires spin at high speed, they can explode, and you or others could be injured. The vehicle can overheat, causing an engine compartment ﬁre or other damage. Spin the wheels as little as possible and avoid going above 35 mph (55 km/h) as shown on the speedometer. For information about using tire chains on your vehicle, see Tire Chains on page 6-73. 5-21 Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. See Traction Control System (TCS) on page 5-6 and StabiliTrak® System on page 5-8. Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears. Release the accelerator pedal while you shift, and press lightly on the accelerator pedal when the transmission is in gear. By slowly spinning the wheels in the forward and reverse directions, you will cause a rocking motion that could free your vehicle. If that does not get your vehicle out after a few tries, it might need to be towed out. If your vehicle does need to be towed out, see Towing Your Vehicle on page 5-27. Loading Your Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certiﬁcation label. {CAUTION: Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle. 5-22 Tire and Loading Information Label The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inﬂation pressures (D). For more information on tires and inﬂation see Tires on page 6-52 and Inﬂation - Tire Pressure on page 6-60. There is also important loading information on the vehicle Certiﬁcation label. It tells you the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axle. See “Certiﬁcation Label” later in this section. Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will ﬁnd the label attached below the door latch. This label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds. 5-23 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be ﬁve 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, the load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Your vehicle is neither designed nor intended to tow a trailer. 5-24 Item Example 1 Total Description Vehicle Capacity Weight for Example 1 = 400 lbs (181 kg) Subtract Occupant Weight @ 150 lbs (68 kg) x 1 = Available Occupant and Cargo Weight = 250 lbs (113 kg) 150 lbs (68 kg) Example 2 Example 3 Item Total Description Vehicle Capacity Weight for Example 2 = 400 lbs (181 kg) Subtract Occupant Weight @ 150 lbs (68 kg) x 2 = Available Cargo Weight = 300 lbs (136 kg) 100 lbs (45 kg) Item Description Total Vehicle Capacity Weight for Example 3 = 400 lbs (181 kg) Subtract Occupant Weight @ 200 lbs (91 kg) x 2 = Available Cargo Weight = 400 lbs (181 kg) 0 lbs (0 kg) Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. 5-25 Certiﬁcation Label And, if you do have a heavy load, you should spread it out. {CAUTION: Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR). If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle. Notice: Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle. A vehicle speciﬁc Certiﬁcation label is attached to the rear edge of the driver’s door. It tells you the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. 5-26 If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. {CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. (cid:129) Put things in the rear area of your vehicle. Try to spread the weight evenly. (cid:129) Never stack heavier things, like suitcases, inside the vehicle so that some of them are above the tops of the seats. (cid:129) Do not leave an unsecured child restraint in your vehicle. (cid:129) When you carry something inside the vehicle, secure it whenever you can. Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Service on page 8-7. Recreational Vehicle Towing Notice: Dolly towing or dinghy towing your vehicle may cause damage because of reduced ground clearance. Always put your vehicle on a ﬂatbed truck. Your vehicle was neither designed nor intended to be towed with any of its wheels on the ground. If your vehicle must be towed, see “Towing Your Vehicle” earlier in this section. Towing a Trailer Your XLR is neither designed nor intended to tow a trailer. 5-27 ✍ NOTES 5-28 Section 6 Service and Appearance Care Service ............................................................6-3 Accessories and Modiﬁcations ..........................6-3 California Proposition 65 Warning .....................6-3 California Perchlorate Materials Requirements ......6-4 Doing Your Own Service Work .........................6-4 Adding Equipment to the Outside of Your Vehicle ..............................................6-4 Fuel ................................................................6-5 Gasoline Octane ............................................6-5 Gasoline Speciﬁcations ....................................6-5 California Fuel ...............................................6-6 Additives .......................................................6-6 Fuels in Foreign Countries ...............................6-7 Filling the Tank ..............................................6-7 Filling a Portable Fuel Container .....................6-10 Checking Things Under the Hood ....................6-10 Hood Release ..............................................6-11 Engine Compartment Overview .......................6-12 Engine Oil ...................................................6-16 Engine Oil Life System ..................................6-20 Engine Air Cleaner/Filter ................................6-22 Automatic Transmission Fluid .........................6-24 Engine Coolant .............................................6-24 Coolant Surge Tank Pressure Cap ..................6-27 Engine Overheating .......................................6-27 Overheated Engine Protection Operating Mode ........................................6-29 Cooling System ............................................6-30 Power Steering Fluid .....................................6-35 Windshield Washer Fluid ................................6-36 Brakes ........................................................6-37 Battery ........................................................6-40 Jump Starting ...............................................6-41 Rear Axle .......................................................6-46 Headlamp Aiming ...........................................6-47 Headlamp Vertical Aiming ..............................6-48 Bulb Replacement ..........................................6-50 Windshield Replacement .................................6-50 Windshield Wiper Blade Replacement ..............6-50 Tires ..............................................................6-52 Winter Tires (XLR-V) .....................................6-53 Tire Sidewall Labeling ...................................6-54 Tire Terminology and Deﬁnitions .....................6-56 Run-Flat Tires ..............................................6-58 Inﬂation - Tire Pressure .................................6-60 Tire Pressure Monitor System .........................6-61 Tire Pressure Monitor Operation .....................6-63 6-1 Section 6 Service and Appearance Care Tire Inspection and Rotation ...........................6-65 When It Is Time for New Tires .......................6-66 Buying New Tires .........................................6-67 Different Size Tires and Wheels ......................6-68 Uniform Tire Quality Grading ..........................6-69 Wheel Alignment and Tire Balance ..................6-70 Wheel Replacement ......................................6-70 Tire Chains ..................................................6-73 Lifting Your Vehicle .......................................6-74 If a Tire Goes Flat ........................................6-78 Appearance Care ............................................6-80 Interior Cleaning ...........................................6-80 Fabric/Carpet ...............................................6-81 Leather .......................................................6-82 Instrument Panel, Vinyl, and Other Plastic Surfaces ........................................6-82 Wood Panels ...............................................6-82 Speaker Covers ............................................6-82 Care of Safety Belts ......................................6-83 Weatherstrips ...............................................6-83 Washing Your Vehicle ...................................6-83 Cleaning Exterior Lamps/Lenses .....................6-84 Finish Care ..................................................6-84 Windshield and Wiper Blades .........................6-85 Aluminum or Chrome-Plated Wheels and Trim ..................................................6-85 Tires ...........................................................6-86 Sheet Metal Damage .....................................6-86 Finish Damage .............................................6-87 Underbody Maintenance ................................6-87 Fiberglass Springs (Composite Springs) ...........6-87 Chemical Paint Spotting .................................6-87 Vehicle Care/Appearance Materials ..................6-88 Vehicle Identiﬁcation ......................................6-89 Vehicle Identiﬁcation Number (VIN) .................6-89 Service Parts Identiﬁcation Label .....................6-89 Electrical System ............................................6-89 Add-On Electrical Equipment ..........................6-89 Windshield Wiper Fuses ................................6-90 Power Windows and Other Power Options .......6-90 Fuses and Circuit Breakers ............................6-90 Instrument Panel Fuse Block ..........................6-90 Underhood Fuse Block ..................................6-94 Capacities and Speciﬁcations ..........................6-97 6-2 Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes, traction control and stability control. Some of these accessories could even cause malfunction or damage not covered by warranty. GM Accessories are designed to complement and function with other systems on your vehicle. Your GM dealer/retailer can accessorize your vehicle using genuine GM Accessories. When you go to your GM dealer/retailer and ask for GM Accessories, you will know that GM-trained and supported service technicians will perform the work using genuine GM Accessories. Also, see Adding Equipment to Your Airbag-Equipped Vehicle on page 1-51. California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals. 6-3 If you want to do some of your own service work, you should use the proper service manual. It tells you much more about how to service your vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 8-16. Your vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-50. You should keep a record with all parts receipts and list the mileage and the date of any service work you perform. See Maintenance Record on page 7-15. Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of your vehicle. California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate. Doing Your Own Service Work {CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. (cid:129) Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task. (cid:129) Be sure to use the proper nuts, bolts, and other fasteners. English and metric fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt. 6-4 Fuel Use of the recommended fuel is an important part of the proper maintenance of your vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. The 8th digit of the Vehicle Identiﬁcation Number (VIN) shows the code letter or number that identiﬁes your vehicle’s engine. The VIN is at the top left of the instrument panel. See Vehicle Identiﬁcation Number (VIN) on page 6-89. Gasoline Octane If your vehicle has the 4.6L V8 engine (VIN Code A), use premium unleaded gasoline with a posted octane rating of 91 or higher. You can also use regular unleaded gasoline rated at 87 octane or higher, but your vehicle’s acceleration could be slightly reduced, and you might notice a slight audible knocking noise, commonly referred to as spark knock. If the octane is less than 87, you might notice a heavy knocking noise when you drive. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible. Otherwise, you could damage the engine. If you are using gasoline rated at 87 octane or higher and you hear heavy knocking, the engine needs service. If your vehicle has the 4.4L V8 engine (VIN Code D), use premium unleaded gasoline with a posted octane rating of 91 or higher. For best performance, use premium unleaded gasoline with a posted octane rating of 93. In an emergency, you can use regular unleaded gasoline with an octane rating of 87 or higher. If 87 octane fuel is used, do not perform any aggressive driving maneuvers such as wide open throttle applications. You might also hear audible spark knock during acceleration. Reﬁll the tank with premium fuel as soon as possible to avoid damaging the engine. If you are using gasoline rated at 91 octane or higher and you hear heavy knocking, the engine needs service. Gasoline Speciﬁcations At a minimum, gasoline should meet ASTM speciﬁcation D 4814 in the United States or CAN/CGSB-3.5 or 3.511 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT. See Additives on page 6-6 for additional information. 6-5 California Fuel If your vehicle is certiﬁed to meet California Emissions Standards, it is designed to operate on fuels that meet California speciﬁcations. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, your vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance might be affected. The malfunction indicator lamp could turn on and your vehicle might fail a smog-check test. See Malfunction Indicator Lamp on page 3-54. If this occurs, return to your authorized dealer/retailer for diagnosis. If it is determined that the condition is caused by the type of fuel used, repairs might not be covered by your warranty. Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. To help keep fuel injectors and intake valves clean, or if your vehicle experiences problems due to dirty injectors or valves, 6-6 look for gasoline that is advertised as TOP TIER Detergent Gasoline. Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the speciﬁcations described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: Your vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under your warranty. Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT. We recommend against the use of such gasolines. Fuels containing MMT can reduce the life of spark plugs and the performance of the emission control system could be affected. The malfunction indicator lamp might turn on. If this occurs, return to your dealer/retailer for service. Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to ﬁnd. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by your warranty. To check the fuel availability, ask an auto club, or contact a major oil company that does business in the country where you will be driving. Filling the Tank {CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle. Do not use cellular phones. Keep sparks, ﬂames, and smoking materials away from fuel. (Continued) CAUTION: CAUTION: (Continued) Do not leave the fuel pump unattended when refueling your vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel. The tethered fuel cap is located behind a hinged fuel door on the driver’s side of the vehicle. 6-7 The fuel door release button is located on the left side of the instrument panel. The button only works when the vehicle is in PARK (P) or NEUTRAL (N) and the valet lockout button is in OFF. An alternate fuel door release is located inside the trunk behind a panel on the driver’s side of the vehicle. Pull the handle to release the fuel door. To remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the hook on the fuel door. {CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way. 6-8 Be careful not to spill fuel. Do not top off or overﬁll the tank and wait a few seconds after you have ﬁnished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See Washing Your Vehicle on page 6-83. When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 3-54. The CHECK GAS CAP message in the Driver Information Center (DIC) will be displayed if the fuel cap is not properly installed. {CAUTION: If a ﬁre starts while you are refueling, do not remove the nozzle. Shut off the ﬂow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately. If you need a new fuel cap, be sure to get Notice: the right type. Your dealer/retailer can get one for you. If you get the wrong type, it may not ﬁt properly. This may cause your malfunction indicator lamp to light and may damage your fuel tank and emissions system. See Malfunction Indicator Lamp on page 3-54. 6-9 Filling a Portable Fuel Container {CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: (cid:129) Dispense fuel only into approved containers. (cid:129) Do not ﬁll a container while it is inside a vehicle, in a vehicle’s trunk, pickup bed, or on any surface other than the ground. (cid:129) Bring the ﬁll nozzle in contact with the inside of the ﬁll opening before operating the nozzle. Contact should be maintained until the ﬁlling is complete. (cid:129) Do not smoke while pumping fuel. (cid:129) Do not use a cellular phone while pumping fuel. Checking Things Under the Hood {CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. {CAUTION: Things that burn can get on hot engine parts and start a ﬁre. These include liquids like fuel, oil, coolant, brake ﬂuid, windshield washer and other ﬂuids, and plastic or rubber. You or others could be burned. Be careful not to drop or spill things that will burn onto a hot engine. 6-10 Hood Release To lift the hood, use the following steps: 1. Pull the lever with this symbol on it. It is located on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and ﬁnd the secondary hood release lever. The lever is located under the hood near the center of the vehicle. Move the release lever to the right and raise the hood. Before closing the hood, be sure all ﬁller caps are on properly. Then pull the hood down and close it ﬁrmly. 6-11 Engine Compartment Overview When you open the hood on the 4.6L V8 engine, here is what you will see: 6-12 A. Battery. See Battery on page 6-40. B. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-42. C. Underhood Fuse Block. See Underhood Fuse Block on page 6-94. D. Power Steering Fluid. See Power Steering Fluid on page 6-35. E. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 6-22. F. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 6-16. G. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 6-16. H. Brake Master Cylinder Reservoir. See “Brake Fluid” under Brakes on page 6-37. I. Engine Coolant Surge Tank and Pressure Cap. See Coolant Surge Tank Pressure Cap on page 6-27. J. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 6-36. 6-13 When you open the hood on the 4.4L V8 XLR-V engine, here is what you will see: 6-14 A. Battery. See Battery on page 6-40. B. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-42. C. Underhood Fuse Block. See Underhood Fuse Block on page 6-94. D. Power Steering Fluid. See Power Steering Fluid on page 6-35. E. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 6-22. F. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 6-16. G. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 6-16. H. Brake Master Cylinder Reservoir. See “Brake Fluid” under Brakes on page 6-37. I. Engine Coolant Surge Tank and Pressure Cap. See Coolant Surge Tank Pressure Cap on page 6-27. J. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 6-36. 6-15 Engine Oil If the LOW OIL LEVEL or LOW OIL PRESSURE message on the Driver Information Center (DIC) appears, check the engine oil level right away. For more information, see LOW OIL LEVEL and LOW OIL PRESSURE under DIC Warnings and Messages on page 3-63. You should check the engine oil level regularly; this is an added reminder. Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 6-12 for the location of the engine oil dipstick. 1. Turn off the engine and give the oil several minutes to drain back into the oil pan. If you do not do this, the oil dipstick might not show the actual level. 2. Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. 6-16 When to Add Engine Oil See Engine Compartment Overview on page 6-12 for the location of the engine oil ﬁll cap. If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 6-97. Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. Be sure to add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when you are through. 6-17 What Kind of Engine Oil to Use Look for three things: (cid:129) GM4718M Your vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard. Look for and use only an oil that meets GM Standard GM4718M. If you use oils that do not have the Notice: GM4718M Standard designation, you can cause engine damage not covered by your warranty. (cid:129) SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50. (cid:129) American Petroleum Institute (API) starburst symbol 6-18 Oils meeting these requirements should have the starburst symbol on the container. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). Look for this on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM4718M and have the starburst symbol on the front of the oil container. Your vehicle’s engine is ﬁlled at the factory with a Mobil 1® synthetic oil, which meets all requirements for your vehicle. Substitute Engine Oil: When adding oil to maintain engine oil level, oil meeting GM Standard GM4718M may not be available. You can add substitute oil designated SAE 5W-30 with the starburst symbol at all temperatures. Substitute oil not meeting GM Standard GM4718M should not be used for an oil change. Engine Oil Additives Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM4718M are all you need for good performance and engine protection. 6-19 Engine Oil Life System When to Change Engine Oil Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably. For the oil life system to work properly, you must reset the system every time the oil is changed. Notice: engine uses a special oil ﬁlter. The use of any other engine oil ﬁlter could lead to ﬁlter failure and result in severe engine damage. Damage caused by use of the wrong engine oil ﬁlter would not be covered by your new vehicle warranty. If your vehicle is an XLR-V model, the When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE OIL NOW message in the DIC will come on. See DIC Warnings and Messages on page 3-63. Change the oil as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the oil life system might not indicate that an oil change is necessary for over a year. However, the engine oil and ﬁlter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service people who will perform this work using genuine parts and reset the system. It is also important to check the oil regularly and keep it at the proper level. If the system is ever reset accidentally, you must change the oil at 3,000 miles (5 000 km) since your last oil change. Remember to reset the oil life system whenever the oil is changed. 6-20 How to Reset the Engine Oil Life System and the Oil Life Indicator The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to a CHANGE OIL NOW message in the DIC being turned on, reset the system. After the oil has been changed, the CHANGE OIL NOW message and the oil life indicator must be reset. To reset the message: 1. Press the up or down arrow to scroll the DIC to show OIL LIFE. 2. Once the XXX% ENGINE OIL LIFE menu item is highlighted, press and hold the RESET button until the percentage shows 100%. If the percentage does not return to 100% or if the CHANGE OIL NOW message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner. Wash or properly dispose of clothing or rags containing used engine oil. See the manufacturer’s warnings about the use and disposal of oil products. Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ﬁlter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water. Instead, recycle it by taking it to a place that collects used oil. If you have a problem properly disposing of used oil, ask your dealer/retailer, a service station, or a local recycling center for help. 6-21 Engine Air Cleaner/Filter See Engine Compartment Overview on page 6-12 for the location of the engine air cleaner/ﬁlters. When to Inspect the Engine Air Cleaner/Filters Inspect the air cleaner/ﬁlters at the Maintenance II intervals and replace them at the ﬁrst oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 7-4 for more information. If you are driving in dusty/dirty conditions, inspect the ﬁlters at each engine oil change. How to Inspect the Engine Air Cleaner/Filters To inspect the air cleaner/ﬁlters, remove the ﬁlters from the vehicle and lightly shake the ﬁlters to release loose dust and dirt. If the ﬁlters remain caked with dirt, new ﬁlters are required. 6-22 To inspect or replace the ﬁlters, do the following: 1. Some XLR-V vehicles, have a single piece black cover that snaps over the entire air cleaner assembly. For vehicles with this cover, simply pull it’s left/right sides toward the outside of the vehicle and lift up to remove cover. Reinstall the cover when you are ﬁnished inspecting/replacing the ﬁlters. 2. Move the clasps on the top of the engine air cleaner/ﬁlter cover forward to unlatch the cover. 3. Lift the front of the cover at an angle and remove. This is necessary due to the four tabs located on the rear of the cover. 4. Remove the engine air cleaner/ﬁlter element and any loose debris that might be found in the air cleaner base. 5. Inspect or replace the ﬁlter. 6. Repeat the procedure for the second air cleaner/ﬁlter. Reverse the above procedure to reinstall the engine air cleaner ﬁlter housings. {CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop ﬂames if the engine backﬁres. If it is not there and the engine backﬁres, you could be burned. Do not drive with it off, and be careful working on the engine with the air cleaner/ﬁlter off. If the air cleaner/ﬁlter is off, a backﬁre can Notice: cause a damaging engine ﬁre. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner/ﬁlter in place when you are driving. 6-23 Automatic Transmission Fluid How to Check Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to the dealer/retailer service department and have it repaired as soon as possible. There is a special procedure for checking and changing the transmission ﬂuid. Because this procedure is difficult, you should have this done at the dealer/retailer service department. Contact your dealer/retailer for additional information or the procedure can be found in the service manual. To purchase a service manual, see Service Publications Ordering Information on page 8-16. Notice: Use of the incorrect automatic transmission ﬂuid may damage your vehicle, and the damages may not be covered by your warranty. Always use the automatic transmission ﬂuid listed in Recommended Fluids and Lubricants on page 7-11. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 7-5, and be sure to use the ﬂuid listed in Recommended Fluids and Lubricants on page 7-11. 6-24 Engine Coolant The cooling system in your vehicle is ﬁlled with DEX-COOL® engine coolant. This coolant is designed to remain in your vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, if you add only DEX-COOL® extended life coolant. The following explains your cooling system and how to add coolant when it is low. If you have a problem with engine overheating, see Engine Overheating on page 6-27. A 50/50 mixture of clean, drinkable water and DEX-COOL® coolant will: (cid:129) Giving freezing protection down to −34°F (−37°C). (cid:129) Give boiling protection up to 265°F (129°C). (cid:129) Protect against rust and corrosion. (cid:129) Help keep the proper engine temperature. Let the warning lights and gages work as they should. Notice: Using coolant other than DEX-COOL® may cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant may require changing sooner, at the ﬁrst maintenance service after each 30,000 miles (50 000 km) or 24 months, whichever occurs ﬁrst. Any repairs would not be covered by your warranty. Always use DEX-COOL® (silicate-free) coolant in your vehicle. (cid:129) What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. {CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ﬁre and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant. If you use an improper coolant mixture, Notice: your engine could overheat and be badly damaged. The repair cost would not be covered by your warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts. If you have to add coolant more than four times a year, have your dealer check your cooling system. Notice: in your vehicle’s cooling system, you could damage your vehicle. Use only the proper mixture of the engine coolant listed in this manual for the cooling system. See Recommended Fluids and Lubricants on page 7-11 for more information. If you use extra inhibitors and/or additives 6-25 {CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the surge tank pressure cap — even a little — when the engine and radiator are hot. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark, located on the side of the surge tank that faces the front. If the LOW COOLANT message on the Driver Information Center (DIC) comes on and stays on, it means you are low on engine coolant. See DIC Warnings and Messages on page 3-63 for more information. Checking Coolant The engine coolant surge tank is located toward the rear of the engine compartment on the driver’s side of the vehicle. For more information on location, see Engine Compartment Overview on page 6-12. 6-26 Adding Coolant If you need more coolant, add the proper DEX-COOL® coolant mixture at the surge tank, but only when the engine is cool. {CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When replacing the pressure cap, press down and turn it clockwise until you hear a clicking sound. Make sure the cap is hand-tight and fully seated. Coolant Surge Tank Pressure Cap If the pressure cap is not tightly installed, Notice: coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. The coolant surge tank pressure cap must be fully installed on the coolant surge tank. See Engine Compartment Overview on page 6-12 for more information on location. Engine Overheating You will ﬁnd a COOLANT OVER TEMP message or an ENGINE HOT, STOP ENGINE message displayed in the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-63. You will also hear a chime. There is also an engine coolant temperature gage on the instrument panel cluster. See Engine Coolant Temperature Gage on page 3-53. 6-27 If Steam Is Coming From Your Engine {CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when the vehicles engine is overheated, the liquids in it can catch ﬁre. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. See Overheated Engine Protection Operating Mode on page 6-29 for information on driving to a safe place in an emergency. If your engine catches ﬁre because you Notice: keep driving with no coolant, your vehicle can be badly damaged. The costly repairs would not be covered by your warranty. See Overheated Engine Protection Operating Mode on page 6-29 for information on driving to a safe place in an emergency. If No Steam Is Coming From Your Engine An overheat warning, along with a low coolant message, can indicate a serious problem. If you get an engine overheat warning with no low coolant message, but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: (cid:129) Climb a long hill on a hot day. (cid:129) Stop after high-speed driving. Idle for long periods in traffic. Tow a trailer. 6-28 (cid:129) (cid:129) If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle. 2. Set the climate controls to the highest heat setting and fan speed and open the windows as necessary. If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning does not come back on, you can drive normally. If the warning continues, pull over, stop, and park your vehicle right away. If there is still no sign of steam, idle the engine for three minutes while you are parked. If you still have the warning, turn off the engine and get everyone out of the vehicle until it cools down. Also, see “Overheated Engine Protection Operating Mode” later in this section. You may decide not to lift the hood but to get service help right away. Overheated Engine Protection Operating Mode This operating mode allows your vehicle to be driven to a safe place in an emergency situation. If an overheated engine condition exists and the DIC message ENGINE HOT, STOP ENGINE is displayed, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage. In this mode, you will notice a signiﬁcant loss in power and engine performance. Driving extended miles (km) in the overheat protection mode should be avoided. Notice: After driving in the overheated engine protection operating mode, to avoid engine damage, allow the engine to cool before attempting any repair. The engine oil will be severely degraded. Repair the cause of coolant loss, change the oil and reset the oil life system. See Engine Oil on page 6-16. 6-29 Cooling System When you decide it is safe to lift the hood, here is what you will see: {CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing, and tools away from any underhood electric fan. If the coolant inside the coolant surge tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. A low coolant level should be indicated by a LOW COOLANT message on the Driver Information Center (DIC). If it is, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system. A. Electric Engine Cooling Fan B. Coolant Surge Tank with Pressure Cap 6-30 {CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned. Get any leak ﬁxed before you drive the vehicle. If there seems to be no leak, with the engine on, check to see if the electric engine cooling fan is running. If the engine is overheating, the fan should be running. If it is not, your vehicle needs service. Notice: Engine damage from running your engine without coolant is not covered by your warranty. See Overheated Engine Protection Operating Mode on page 6-29 for information on driving to a safe place in an emergency. Notice: Using coolant other than DEX-COOL® may cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner, at 30,000 miles (50 000 km) or 24 months, whichever occurs ﬁrst. Any repairs would not be covered by the warranty. Always use DEX-COOL® (silicate-free) coolant in the vehicle. 6-31 How to Add Coolant to the Coolant Surge Tank If you have not found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level is not at the FULL COLD mark on the front of the coolant surge tank, add a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant at the coolant surge tank, but be sure the cooling system, including the coolant surge tank pressure cap, is cool before you do it. See Engine Coolant on page 6-24 for more information. If no coolant is visible in the surge tank, add coolant as follows: {CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the coolant surge tank pressure cap — even a little — they can come out at high speed. Never turn the CAUTION: (Continued) CAUTION: (Continued) cap when the cooling system, including the coolant surge tank pressure cap, is hot. Wait for the cooling system and coolant surge tank pressure cap to cool if you ever have to turn the pressure cap. {CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch ﬁre and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL® coolant. 6-32 In cold weather, water can freeze and crack Notice: the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture. {CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left. 2. Then keep turning the cap and remove it. 6-33 3. Fill the coolant surge tank with the proper mixture until the level inside the surge tank stabilizes at the FULL COLD mark on the front of the surge tank. 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower. If the level is lower, add more of the proper mixture to the coolant surge tank until the level stabilizes at the FULL COLD mark on the coolant surge tank. 5. Then replace the pressure cap. Be sure the cap is hand-tight and fully seated. 6-34 If the LOW COOLANT message does not appear on the Driver Information Center (DIC) after two minutes, the coolant is at the proper ﬁll level. If a LOW COOLANT message does appear, repeat Steps 1 through 3 then reinstall the pressure cap, or see your dealer. How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the ignition off and let the engine compartment cool down. Power Steering Fluid See Engine Compartment Overview on page 6-12 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4. Replace the cap and completely tighten it. 5. Remove the cap again and look at the ﬂuid level on the dipstick. The level should be at the FULL COLD mark. If necessary, add only enough ﬂuid to bring the level up to the mark. What to Use To determine what kind of ﬂuid to use, see Recommended Fluids and Lubricants on page 7-11. Always use the proper ﬂuid. Notice: Use of the incorrect ﬂuid may damage your vehicle and the damages may not be covered by your warranty. Always use the correct ﬂuid listed in Recommended Fluids and Lubricants on page 7-11. 6-35 Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing. Adding Washer Fluid The LOW WASHER FLUID message will be displayed on the Driver Information Center (DIC) when the ﬂuid is low. Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 6-12 for reservoir location. Notice: (cid:129) When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. (cid:129) Do not mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system. Also, water does not clean as well as washer ﬂuid. Fill the washer ﬂuid tank only three-quarters full when it is very cold. This allows for ﬂuid expansion if freezing occurs, which could damage the tank if it is completely full. (cid:129) Do not use engine coolant (antifreeze) in your windshield washer. It can damage the vehicle’s windshield washer system and paint. 6-36 (cid:129) Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 6-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear. When new linings are put in, the ﬂuid level goes back up. The other reason is that ﬂuid is leaking out of the brake hydraulic system. If it is, you should have the brake hydraulic system ﬁxed, since a leak means that sooner or later the brakes will not work well. It is not a good idea to top off the brake ﬂuid. Adding brake ﬂuid will not correct a leak. If ﬂuid is added when the linings are worn, there will be too much ﬂuid when new brake linings are installed. Add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system. {CAUTION: If you have too much brake ﬂuid, it can spill on the engine. The ﬂuid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged. Add brake ﬂuid only when work is done on the brake hydraulic system. See “Checking Brake Fluid” in this section. Refer to the Maintenance Schedule to determine when to check the brake ﬂuid. See Scheduled Maintenance on page 7-4. 6-37 Checking Brake Fluid The brake ﬂuid can be checked without taking off the cap by looking at the brake ﬂuid reservoir. The ﬂuid level should be above the MIN mark on the reservoir. If it is not, have the brake hydraulic system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is between the MIN and MAX marks. What to Add When you do need brake ﬂuid, use only DOT-3 brake ﬂuid. Refer to Recommended Fluids and Lubricants on page 7-11. Use new brake ﬂuid from a sealed container only. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir. {CAUTION: With the wrong kind of ﬂuid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake ﬂuid. Notice: (cid:129) Using the wrong ﬂuid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of ﬂuid. If you spill brake ﬂuid on your vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be careful not to spill brake ﬂuid on your vehicle. If you do, wash it off immediately. See Washing Your Vehicle on page 6-83. 6-38 (cid:129) Brake Wear Your vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly. {CAUTION: The brake wear warning sound means that soon the brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates can cause a brake squeal when the brakes are ﬁrst applied or lightly applied. This does not mean something is wrong with the brakes. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment As you make brake stops, the disc brakes automatically adjust for wear. Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality brake parts. When you replace parts of the braking system — for example, when the brake linings wear down and you need new ones put in — be sure you get new approved replacement parts. If you do not, the brakes might not work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between the front and rear brakes can change — for the worse. The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts. 6-39 Battery Your vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. For battery replacement, see your dealer/retailer or the service manual. To purchase a service manual, see Service Publications Ordering Information on page 8-16. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. Vehicle Storage Infrequent Usage: If you drive your vehicle infrequently, remove the black, negative (−) cable from the battery. This will help keep the battery from running down. See “Power Window Initialization” in Power Windows on page 2-17. Extended Storage: For extended storage of your vehicle, remove the black, negative (−) cable from the battery or use a battery trickle charger. This will help maintain the charge of the battery over an extended period of time. You must close all doors and the trunk before reconnecting the battery. After reconnecting the battery, you must press the unlock button on the keyless access transmitter. Failure to follow this procedure could result in the alarm sounding. Pressing unlock on the keyless access transmitter will stop the alarm. {CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 6-41 for tips on working around a battery without getting hurt. 6-40 Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. {CAUTION: Batteries can hurt you. They can be dangerous because: (cid:129) They contain acid that can burn you. (cid:129) They contain gas that can explode or ignite. (cid:129) They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you. If you try to start your vehicle by pushing Notice: or pulling it, you could damage your vehicle. Do not push or pull your vehicle to start it; instead, use the jump starting procedure in this manual to start your vehicle when the battery has run down. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system. If the other vehicle’s system is not a 12-volt Notice: system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake ﬁrmly on both vehicles involved in the jump start procedure. Put an automatic transmission in PARK (P) or a manual transmission in NEUTRAL before setting the parking brake. 6-41 {CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has ﬁller caps, be sure the right amount of ﬂuid is there. If it is low, add water to take care of that ﬁrst. If you do not, explosive gas could be present. Battery ﬂuid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ﬂush the place with water and get medical help immediately. If you leave your radio or other accessories Notice: on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3. Turn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio! 4. Open the hoods and locate the batteries. Find the positive (+) and negative (−) terminal locations on each vehicle. See Engine Compartment Overview on page 6-12 for more information on location. {CAUTION: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. 6-42 {CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative (−) will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks. 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 6-43 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part or to a remote negative (−) terminal on the vehicle with the dead battery. 9. Connect the other end of the negative (−) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less. 10. Now start the vehicle with the good battery and run the engine for a while. 11. Try to start the vehicle that had the dead battery. If it will not start after a few tries, it probably needs service. If the jumper cables are connected or Notice: removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal. 6-44 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part B. Good Battery C. Dead Battery To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3. Disconnect the red positive (+) cable from the vehicle with the good battery. 4. Disconnect the red positive (+) cable from the other vehicle. Perform “Power Window Initialize” steps under Power Windows on page 2-17, if the vehicle has experienced power loss. 6-45 Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant If the level is below the bottom of the ﬁller plug hole, you will need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole. What to Use To add lubricant when the level is low, use SAE 75W-90 Synthetic Gear Lubricant (GM Part No. 89021677) or equivalent meeting GM Speciﬁcation 9986115. To completely reﬁll after draining, add 4.7 ounces (140 ml) of Limited-Slip Differential Lubricant Additive (GM Part No. 1052358) or equivalent. Then ﬁll to the bottom of the ﬁller plug hole with the Synthetic Gear Lubricant. To get an accurate reading, the vehicle should be on a level surface. 6-46 Headlamp Aiming The high intensity discharge (HID) visual optical aiming type headlamps have been preset at the factory and should need no further adjustment. If you suspect that the headlamps need to be reaimed, it is recommended that you contact your dealer/retailer for service. However, it is possible for you to re-aim your headlamps as described in the following procedure. Notice: To make sure your headlamps are aimed properly, read all the instructions before beginning. Failure to follow these instructions could cause damage to headlamp parts. The vehicle should be properly prepared as follows: The vehicle should be placed so the headlamps are 25 ft (7.6 m) from a light colored wall. The vehicle must have all four tires on a perfectly level surface which is level all the way to the wall. The vehicle should be placed so it is perpendicular to the wall. The vehicle should not have any snow, ice or mud attached to it. The vehicle should be fully assembled and all other work stopped while headlamp aiming is being done. The vehicle should be normally loaded with a full tank of fuel and one person or 160 lbs (75 kg) on the driver seat. Tires should be properly inﬂated. (cid:129) Start the vehicle and rock it to level the suspension. 6-47 (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) (cid:129) Headlamp aiming is done with the low-beam headlamps. The high-beam headlamps are correctly aimed if the low-beam headlamps are aimed properly. The headlamp aiming device is under the hood near the headlamps. Adjustment screws can be turned with an E8 Torx® socket or T15 Torx screwdriver. Headlamp Vertical Aiming To properly prepare the vehicle for vertical headlamp aiming see Headlamp Aiming on page 6-47 for more information. To adjust the vertical aim, do the following: Notice: Horizontal aiming must be performed before making any adjustments to the vertical aim. Adjusting the vertical aim ﬁrst will result in an incorrect headlamp aim. 1. Open the hood. See Hood Release on page 6-11 for more information. 2. Locate the aim dot on the inner projector lens of the low-beam headlamp. 3. Measure the distance from the ground to the aim dot on each low-beam headlamp. Record this distance. 6-48 4. At the wall or other ﬂat surface, measure from the ground upward (A) to the recorded distance from Step 3 and mark it. Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp. 5. Draw or tape a horizontal line (B) on the wall or ﬂat surface the width of the vehicle at the height of the mark in Step 4. 6. Turn on the low-beam headlamps and place a piece of cardboard in front of the headlamp not being aimed. This should allow only the beam of light from the headlamp being aimed to be seen on the ﬂat surface. 7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a 6 mm male hex. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line. 6-49 Bulb Replacement It is recommended that all bulbs be replaced by your dealer/retailer. Windshield Replacement Your windshield is part of the Head-Up Display (HUD) system. If you ever have to get your windshield replaced, get one that is designed for HUD or your HUD image may look out of focus. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 7-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 7-13. 9. The top edge of the cut-off should be positioned at the bottom edge of the horizontal tape line. 10. Make sure that the light from the headlamp is positioned at the bottom edge of the horizontal tape line. The lamp on the left (A) shows the correct headlamp aim. The lamp on the right (B) shows the incorrect headlamp aim. 11. Repeat Steps 7 through 9 for the opposite headlamp. 6-50 To replace the windshield wiper blade assembly do the following: 1. Lift the wiper arm away from the windshield. 2. Push the release lever (B) to disengage the hook and push the wiper arm (A) out of the blade (C). 3. Push the new wiper blade securely on the wiper arm until you hear the release lever click into place. 6-51 CAUTION: (Continued) (cid:129) Underinﬂated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your vehicle’s tires are cold. See Inﬂation - Tire Pressure on page 6-60. (cid:129) Overinﬂated tires are more likely to be cut, punctured, or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure. (cid:129) Worn, old tires can cause accidents. If the tire’s tread is badly worn, or if your vehicle’s tires have been damaged, replace them. Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle warranty booklet for details. {CAUTION: Poorly maintained and improperly used tires are dangerous. (cid:129) Overloading your vehicle’s tires can cause overheating as a result of too much ﬂexing. You could have an air-out and a serious accident. See Loading Your Vehicle on page 5-22. CAUTION: (Continued) 6-52 Low-Proﬁle Tires (XLR-V) If your vehicle has P235/45R19 or P255/40R19 size tires, they are classiﬁed as low-proﬁle tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster. Notice: they are more susceptible to damage from road hazards or curb impact than standard proﬁle tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazards like, potholes, or sharp edged objects, or when sliding into a curb. Your vehicle warranty does not cover this type of damage. Keep tires set to the correct inﬂation pressure and, when possible avoid contact with curbs, potholes, and other road hazards. If your vehicle has low-proﬁle tires, Winter Tires (XLR-V) If you expect to drive on snow or ice covered roads often, you may want to get winter tires for your vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads. Winter tires, in general, are designed for increased traction on snow and ice covered roads. With winter tires, there may be decreased dry road traction, increased road noise, and shorter tread life. After switching to winter tires, be alert for changes in vehicle handling and braking. See your dealer for details regarding winter tire availability and proper tire selection. Also, see Buying New Tires on page 6-67. If you choose to use winter tires: (cid:129) Use tires of the same brand and tread type on all four wheel positions. (cid:129) Use only radial ply tires of the same size, load range, and speed rating as the original equipment tires. Winter tires with the same speed rating as your original equipment tires may not be available for H, V, W, Y, and ZR speed rated tires. If you choose winter tires with a lower speed rating, never exceed the tire’s maximum speed capability. 6-53 (B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger (p-metric) tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail. 6-54 (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information see Uniform Tire Quality Grading on page 6-69. (G) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. Tire Size The following illustration shows an example of a typical passenger (p-metric) vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U. S. Tire and Rim Association. (B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall. (C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide. (D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction. (E) Rim Diameter: Diameter of the wheel in inches. (F) Service Description: These characters represent the load range and speed rating of the tire. The load index represents the load carry capacity a tire is certiﬁed to carry. The load index can range from 1 to 279. The speed rating is the maximum speed a tire is certiﬁed to carry a load. Speed ratings range from A to Z. 6-55

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2008 Cadillac XLR Owners Manual