2007 Cadillac XLR Owners Manual

Download PDF Manual
To edit an avoid point/area, do the following: 1. Touch Edit Avoid Point/Area. A list of avoided points will appear. Deleting an Avoid Point/Area To delete an avoid point/area, do the following: 1. Touch Delete Avoid Point/Area. A list of avoided points will appear. 2. Select the avoided point/area you want to change. A map of the avoided area will appear. 3. Use REDUCE or ENLARGE to edit the avoided point. 4. Touch Enter to set your new avoided area. The system will display “Area Adjusted.” 5. Touch Return to go back to the previous screen. 2. Select the avoided point/area you want to delete. 3. The system will ask you to conﬁrm your selection. Touch Yes to delete the avoid point/area or No to cancel. If Yes is selected, the area will no longer be avoided when traveling on a planned route. 4. Touch Return to go back to the previous screen. 258 Enter Destination The DESTINATION menu will give you several ways to plan a route. Touch the Enter Destination screen button from the PLAN ROUTE menu to display the DESTINATION menu. For destination entry methods listed on the second page of the DESTINATION menu, touch the Next Page arrow. Touch the Prev. Page arrow to return to the ﬁrst page. To enter a destination, choose from one of the destination entry methods following in this section. After entering a destination, If available, the system will display up to three routes in a pop-up window indicating the total mileage and time to destination for each route. Select a route by touching NEXT. The map will display each route in a different color. The selected route will be highlighted in red. To start route guidance, touch Start or begin driving your vehicle. Route guidance will automatically begin after a short distance. If you touch CHG ROUTE before touching Start, you will be able to change route preferences. See Route Preference on page 269 for more information. When a route has been planned, it will be highlighted and a bulls-eye symbol will appear on the map to show your ﬁnal destination. If you wish to cancel a route that has been set, see “Cancel Route” under Route Preference on page 269. 259 Easy Planning Route With this destination entry method, you can select a destination using the scroll symbol on the map screen. See Maps on page 271. To use this destination entry method, do the following: 1. Press the MAP key. 2. Touch the map screen twice for the scroll symbol to appear. Touch the map or drag the scroll symbol toward your destination. 3. Touch the map screen continuously to scroll through the map faster. The address of the location on the map will appear at the top of the screen. If needed, use the zoom feature to locate your destination. See “Map Scales” under Maps on page 271 for more information. 4. Touch ENT DEST to set this location as your destination. You may also touch MARK to store this location as a memory point. 5. Touch Enter to plan your route. 260 Address This destination entry method allows you to input an address by providing the system with a house number, street name, and city. Select Street to begin entering the desired address. To use this destination entry method, do the following: 1. Enter the street name using the alpha keypad. See “Alpha-Numeric Keypad” under Using the Navigation System on page 240 for more information. Do not include name extensions such as N. or Drive. For example, the street name N. Civic Center Drive should be entered as Civic Center. As information is entered, the system will automatically search for available names, and List will become available. 2. Touch List to view name choices or continue to spell the street name to further reduce the number of available items. Select a street name. 3. If the street name you entered exists in more than one city on the DVD database, a list of cities will appear. You can select a city from the list, or enter the city name by selecting City. As you begin to enter the city name, you can select the desired city from the list which will appear, or continue to spell the city name to further reduce the number of available items. 4. Once the city name has been selected, enter the house number using the numeric keypad. The system will list the house number range that is available for the street. 5. When you have ﬁnished entering all of the address information, touch Enter to plan your route. 261 All Points of Interest This destination entry method allows you to choose a destination from the point of interest (POI) list. Selecting All Points Of Interest from the DESTINATION menu will bring up the alpha keypad. While inputting a POI or city name, the List option will become available. As information is entered, the system will search for available POI and city names based on the information given. The system will supply a list of names to make a selection from when the choices are ﬁve or less. You may search for a POI using the following three methods: (cid:127) Touch NAME to type in a POI by name using the alpha key pad. As you type in a name, the system will search for an available match to your input. Select the desired POI. (cid:127) Select a POI by touching CATEGORY. Use the arrows to scroll through the categories listed. Select a category along with any appropriate sub-categories. If the list of available POIs for the selected category is too long, you may need to enter the POI’s name or city. (cid:127) Select CITY, then type in the city you wish to select a POI from. Choose a city from the list of cities that will appear. If the list of POIs for the selected city is too long, enter the POI’s name or choose a category. While inputting a POI or city name, the List option will become available. Touch List to view the list of name choices, or continue to spell the name to further reduce the list of available items. 262 The system will list all POIs available. You can sort by name using NAME SORT or touch DIST SORT to list POIs by distance from your current location. Memory Points This destination entry method allows you to set a memory point as your destination. Each time you store a destination from the map screen, the destination is stored under MARKED POINT. See Edit Memory Point on page 250 for more information. Select a location from the list. The system will show the selected POI on the map. If available, a pop-up window will be displayed. Touch INFO to view the POI’s name, address, city, and phone number, if available. Touch Enter to plan your route. You must have destinations stored as memory points to select from PERSONAL, BUSINESS, ENTERTAINMENT, or MARKED POINT. If you have renamed the memory point category name(s), the name(s) will appear as you changed them. 263 To select a destination using this entry method, do the following: 1. Touch the Memory Points symbol. 2. Select a category. 3. Select a destination. Use the arrows to scroll through the memory points. They can be sorted by date, name, distance, and icon. 4. Touch Enter to plan your route. Previous Destination This destination entry method allows you to select a destination by choosing from a list of the last 10 destinations entered into the system. 264 To select a previous destination, do the following: 1. Touch the Previous Destination symbol. 2. Touch the screen button next to the desired destination to select it. Use the arrows if necessary to view the entire list of previous destinations. 3. Touch Enter to plan your route. Previous Starting Point This destination entry method allows you to select the last start point as your destination. To select the previous start point as your destination, do the following: 1. Touch Previous Destination. 2. Touch the Previous starting point screen button. 3. Touch Enter to plan your route. Home This destination entry method allows you to select a destination that has been previously stored as Home. To choose Home as your destination, do the following: 1. Touch the Home symbol. 2. Touch Enter to plan your route. 265 Set by Map This destination entry method allows you to select a destination by using the scroll symbol. 2. Use the scroll symbol to select the desired destination. The zoom in and zoom out feature can be used to assist you in ﬁnding the desired location. See “Map Scales” under Maps on page 271. 3. Touch Enter to plan your route. Freeway Entrance/Exit This destination entry method allows you to select either a freeway entrance or an exit as a destination. To use this feature, do the following: 1. Touch the Set By Map symbol. Current vehicle position will be shown on the map screen. 266 4. Select a freeway from the list. 5. The ENTRANCE or EXIT options will appear. Choose ENTRANCE to select the entrance to the freeway, or EXIT to select the exit ramp of the freeway. When either button is touched, it will give an alphabetical list of freeway entrance and exit ramps on the freeway you entered. You may touch DIST SORT to sort the list by distance from your current location, or NAME SORT to sort the list by name. 6. Select the desired freeway entrance or exit from the list. A map will appear with the destination shown. 7. Touch Enter to plan your route. To enter a freeway name, do the following: 1. Touch the Freeway Entrance/Exit symbol. 2. Enter the freeway name using the alpha key pad. Freeways sometimes have a name and a number associated with them which you may need to refer to when entering freeway information. Freeways are also referred to by their abbreviated names. For example, Interstate 75 in the U.S. is selected by entering I-75. As you enter a freeway name, the List option will become available. 3. Touch List to view the list of available name choices or continue to spell the name to further reduce the list of available items. The system will supply a list of names when the choice is ﬁve or less. If you are unsuccessful when inputting a name, the name may need to be input differently, the map DVD database may not contain this information, or the name may be misspelled. 267 Intersection This destination entry method allows you to select a destination by inputting the intersecting roads you wish to travel to. To enter an intersection, do the following: 1. Touch the Intersection symbol. 2. Using the alpha keypad, enter the name of the ﬁrst street in the intersection. 268 3. To view a list of choices, touch List or continue to spell the name to further reduce the list of available items. The system will display a list of the intersecting streets if the number of intersecting streets is ﬁve or less. 4. Select the ﬁrst street. 5. Now enter the second street name. 6. Select the second street name from the list of intersecting streets. To view a list of choices, touch List or continue to spell the name to further reduce the list of available items. The system will display a list of intersecting streets if the number of intersecting streets is ﬁve or less. If there are multiple intersections with the same two roads, the system will display a list of cities to choose from. Choose a city from this list. A map with the intersections for that city will appear. 7. Touch Enter to plan your route. Route Preference To change your planning options, use the following instructions. The following options will be available from the ROUTE PREFERENCE menu: Detour This feature allows you to choose a distance in miles/kilometers to detour. Select the detour distance desired for residential roads and freeways. 1. Press the ROUTE key. 2. Touch Route Preference. The system will retain these settings for the next time you use Detour, unless you change them. You may also touch Alternate to provide a new route that does not use previously stored detour settings. Touch Return to go back to the previous screen. 269 Route Setting This feature allows you to display and change the planning methods used each time you plan a route. With planning method options, you are able to select the fastest route based on time or distance, using only major roads, toll roads, and using ferries based on the navigation system’s information and information contained on the map DVD. The following options will be available from the ROUTE SETTING menu: Minimize Time/Distance: The system will calculate the fastest route or shortest route possible. Choose Time for the fastest route or Dist for the shortest route. Use Major Roads: Choose Yes to calculate the best route using only major roads unless a route cannot be found without the use of a secondary road. This selection will not always offer the shortest distance or time to your destination. Use Toll Roads: Choose Yes to calculate the best route using toll roads wherever possible. This selection will not always offer the shortest distance or time to your destination. Use Ferries: Choose Yes to calculate the best route using ferries when possible. This selection will not always offer the shortest distance or time to your destination. 270 Display Whole Route This feature allows you to display your entire planned route. Total mileage and time to destination for the planned route will be displayed on the map screen. Touch Return to go back to the previous menu. Calculate Route This feature allows you to begin route calculation for the selected destination. Cancel Route If you are traveling on a planned route and would like to cancel it, touch Cancel Route. The system will ask you to conﬁrm by touching YES. Touch YES to conﬁrm cancellation of your planned route or touch Return to keep your planned route. Maps This section includes basic information you need to know about the map database. Regional Maps The maps are stored on a DVD-ROM. The 48 contiguous United States and portions of Canada are contained on one disc. The U.S. map database includes interstate freeways, state highways, country roads, and major and general streets. Refer to the “Navigation System Map Disc” manual to view the explanation of map coverage and detailed city lists in each region. The map disc manual will be in your map DVD case when the vehicle is delivered from the factory. Installing the DVD Map Disc When your vehicle is delivered from the factory, the dealer may have installed the map DVD. If the map DVD was not installed in your vehicle when ﬁrst purchased, do the following: 1. Turn the ignition on. 2. With the vehicle in PARK (P), press and hold the TILT key until a beep is heard. The system’s faceplate will open. 3. If already loaded, the map DVD or a CD will eject from the slot. 271 4. Load the map DVD into the slot by inserting it partway. The system will pull it in. 5. Press and release the TILT key to close the faceplate. Notice: Shifting out of PARK (P) with the system’s faceplate open will cause the faceplate to close automatically. This could cause damage to a CD, DVD or the system if it is partially loaded. Before shifting out of PARK (P), make sure that the DVD or CD is loaded properly. The vehicle must be shifted back into PARK (P) to close the faceplate. Once the map DVD is inserted correctly, you will have the following two choices: (cid:127) LANGUAGE (cid:127) You can change the language at this time. See “Language” under Navigation Audio System on page 285 for more information on choosing a language. Once a language has been selected, touch I AGREE to plan a route. The map will appear showing your current vehicle position. I AGREE Ejecting the DVD Map Disc When the DVD map disc is not loaded, you will not be able to use the navigation portion of the system. 1. Turn the ignition on. 2. With the vehicle in PARK (P), press and hold the TILT key until a beep is heard. The system’s faceplate will open. 3. The map DVD will eject from the slot. Pull the disc out. 4. Press and release the TILT key to close the faceplate. Notice: Shifting out of PARK (P) with the system’s faceplate open will cause the faceplate to close automatically. This could cause damage to a CD, DVD or the system if it is partially loaded. Before shifting out of PARK (P), make sure that the DVD or CD is loaded properly. The vehicle must be shifted back into PARK (P) to close the faceplate. 272 Setting the Search Area To determine or change the system’s search area, do the following: 1. Press the ROUTE key. 2. Touch the Enter Destination screen button. 3. Touch Change under the Search Area heading. The system will display a map with each region represented. 4. Select the desired region by touching the appropriate screen button to the left of the U.S. map. The name of the states or the country included in the selected region will be displayed at the bottom of the screen and the region will be highlighted. 5. Touch Enter to set the region as the search area. 6. Touch Return to go back to the previous screen. 273 Map Adjustments The system allows you to adjust the scale of view on the map. The map will scroll automatically based on the direction you are traveling. Map Scales Scrolling the Map Touch anywhere on the map screen twice to display the scroll symbol. To view a larger or smaller scale of the map, touch the map scale arrows. You may also adjust the scale of the map by touching the scale on the bar. The scale of a map can range from 1/32 of a mile (0.05 km) to 128 miles (256 km). 274 Place your ﬁnger on the map screen in any direction outside of the scroll symbol to scroll in that direction. The map will continue to scroll until you remove your ﬁnger. If your vehicle is in PARK (P), the system will initially scroll at a slower rate. The rate will increase if you continue to touch the map screen. If your vehicle is in motion, there is one scroll speed and a limited distance to scroll. You must keep touching the map screen to scroll a longer distance. If your vehicle icon becomes lost while scrolling, press the MAP key to show the vehicle’s current location. You may also use the scroll feature to set a destination. See “Set by Map” under Enter Destination on page 259. Symbols The following symbols are the most common that appear on a map screen. You will see this type of symbol on the map when a waypoint has been planned. Your vehicle is shown as this symbol. It indicates the current position and heading direction of your vehicle on the map. This symbol will appear on the map to show your destination after a route has been planned. The waypoint symbol will be numbered from 1 through 5 depending on how many waypoints have been set. See Edit Waypoint on page 254 for more information on adding waypoints. This symbol indicates the distance to your ﬁnal destination. See Enter Destination on page 259 for more information on planning a route. 275 This symbol indicates the distance and estimated travel time to your ﬁnal destination. The Estimated Travel Time feature must be on for estimated travel time to be displayed. This symbol indicates the distance to your ﬁnal destination in a straight line. This symbol will appear before route guidance begins or if you are on a road where route guidance is not available. 276 This symbol indicates the map with North up. While in North up mode, North will always be at the top of the map screen regardless of which direction the vehicle is traveling. This symbol indicates the map with the vehicle travel direction up, or Heading up. The shaded triangle indicates North. While in Heading up mode, the direction your vehicle is traveling will always be at the top of the map screen. Touch either the North Up heading symbol or the vehicle Heading Up symbol to alternate between settings. This symbol will appear when the navigation system is unable to receive the GPS signal. See Global Positioning System (GPS) on page 281 for more information. When a point of interest (POI) or street address name is too long to be displayed, an arrow will appear. Touch the right or left arrow to scroll through the entire name. This symbol indicates the position of the next turn instruction. While on a planned route, touch this symbol to display the DEST MAP, WHOLE, and TURN LIST options. 277 With these options, you can do the following: Dest (Destination) Map: This option allows you to view the ﬁnal destination location. The destination’s name or address will be displayed on the map screen. Touch Return when ﬁnished. Whole: This option allows you to view the entire planned route. The distance to destination will be displayed on the map screen. Touch Return when ﬁnished. 278 screen as you make each turn. You may also touch the scroll up and down arrows providing scroll is available. Touching the down arrow will bring you to your current location. Touching the up arrow will give you upcoming streets. At times, there may not be names available for entrance or exit ramps. To avoid a turn, touch AVOID next to the turn you want to avoid. You can use REDUCE or ENLARGE to edit the avoided point. Touch Reroute or press the MAP key to calculate your new route. Touch Return to view your current position and to turn the turn list screen off. Touch REROUTE or press the MAP key to calculate a new route. Auto Reroute When your destination is set and you travel off of the planned route, the system will automatically begin to reroute you. You will see the new route highlighted on the screen. 279 Turn List: This option allows you to view a step-by-step listing of upcoming street names, the distance that you will travel on the road, and turns you will need to make during your planned route. After touching Turn List, the system may take some time to create the list. The length of time will vary depending on the length of your route and the planning methods you have selected. The turn list will read from bottom to top. The bottom street name is the street you are currently on. The system automatically updates this Traveling Across Regions If you plan to drive across several states, you may have to change the selected region to represent the area you are traveling to. There are two ways you can plan a destination when traveling across regions. The following method is suggested and provides the most route guidance and map display functions: 1. Change the selected search area region when you get closer to the area you are traveling to. See “Setting the Search Area” under Maps on page 271. 2. Enter your destination and route settings. See Enter Destination on page 259 for more information. If you do not want to use the ﬁrst method, keep your currently selected search area region and enter your destination. This method allows you only to select a destination from the easy planning route method or from the All Points of Interest (POI) categories with the “All Search Areas” comment for US Only. For example, Tourist 280 is a category that features this comment. See Enter Destination on page 259 for more information. If you are traveling in or to Canada and you cross the regional border, the only map scale views available are 4 mi, 8 mi, 31 mi, and 128 mi (8 km, 16 km, 64 km and 256 km). Change the selected search area region when you get closer to the area you are traveling to. See “Setting the Search Area” under Maps on page 271 for more information. Keyless Access System When the engine is started, Driver 1 or Driver 2 will display on the screen. A message will not appear on the screen if the driver is unknown. The number on the back of the transmitter corresponds to driver 1 or driver 2. The navigation system can store memory points for drivers 1 and 2 individually. See Keyless Access System on page 67 for more information. OnStar® System When using the OnStar® system, the audio system will be muted and the navigation voice prompts will be disabled during the call. The volume of the OnStar® call can be adjusted by using the steering wheel volume controls. See OnStar® System on page 107 for more information. Global Positioning System (GPS) The Navigation System determines the position of your vehicle by using satellite signals, various vehicle signals, and map data. At times, other interferences such as the satellite condition, road conﬁguration, the condition of the vehicle and/or other circumstances can interfere with the Navigation’s ability to determine the accurate position of the vehicle. The GPS shows the current position of your vehicle using signals sent by the GPS Satellites of the United States Department of Defense. When your vehicle is not receiving signals from the satellites, a symbol will appear on the map screen. Refer to Symbols on page 275. This system may not be available or interference may occur if the following happens: (cid:127) Signal obstructions caused by tall buildings, large trucks, tunnels, (cid:127) objects located on top of the instrument panel, (cid:127) satellites will not send signals if they are being repaired or improved, (cid:127) after-market glass tinting has been applied to the vehicle’s windows. Notice: Do not apply after-market glass tinting to the vehicle’s windows. Glass tinting will interfere with the system’s ability to receive GPS signals and cause the system to malfunction. You might have to replace the window to correct the problem. This would not be covered by your warranty. For more information if you are experiencing a problem, see If the System Needs Service on page 283 and Problems with Route Guidance on page 283. 281 (cid:127) The vehicle is entering and/or exiting a parking lot, garage, or a lot with a roof. (cid:127) The GPS signal is not received. (cid:127) A roof carrier is installed on your vehicle. (cid:127) The vehicle is being driven with tire chains. (cid:127) The tires are replaced. (cid:127) The tire pressure for your tires is incorrect. (cid:127) The tires are worn. (cid:127) The ﬁrst time the map DVD is inserted. (cid:127) The battery is disconnected for several days. (cid:127) The vehicle is driving in heavy traffic where driving is at low speeds, and the vehicle is stopped and started repeatedly. If you experience problems with your system, see your dealer. Vehicle Positioning At times, the position of the vehicle on the map may be inaccurate due to one or more of the following reasons: (cid:127) The road system has changed. (cid:127) The vehicle is driving on slippery road surfaces such as in sand, gravel, and/or snow. (cid:127) The vehicle is traveling on winding roads. (cid:127) The vehicle is on a long straight road. (cid:127) The vehicle is approaching a tall building or a large vehicle. (cid:127) The surface streets run parallel to a freeway. (cid:127) The vehicle has just been transferred by a vehicle carrier or a ferry. (cid:127) The current position calibration is set incorrectly. (cid:127) The vehicle is traveling at high speed. (cid:127) The vehicle changes directions more than once, or when the vehicle is turning on a turn table in a parking lot. 282 Problems with Route Guidance Inappropriate route guidance may occur under one or more of the following conditions: (cid:127) You have not turned onto the road indicated. (cid:127) Route guidance may not be available when using automatic rerouting for the next right or left turn. (cid:127) The route may not be changed when using automatic rerouting. (cid:127) There is no route guidance when turning at an intersection. (cid:127) Plural names of places may be announced (cid:127) occasionally. It may take a long time to operate automatic rerouting during high-speed driving. (cid:127) Automatic rerouting may display a route returning to the set waypoint if you are heading for a destination without passing through a set waypoint. (cid:127) The route prohibits the entry of a vehicle due to a regulation by time or season or any other regulation which may be given. (cid:127) Some routes may not be searched. (cid:127) The route to the destination may not be shown if there are new roads, if roads have recently changed, or if certain roads are not listed on the map DVD. See Ordering Map DVDs on page 284. To recalibrate the vehicle’s position on the map, see your dealer. If the System Needs Service If your system needs service and you have followed the steps listed here and still are experiencing problems, see your dealer for assistance. 283 Ordering Map DVDs You will receive two free DVD map disc updates with the purchase of your new vehicle. Updates are necessary to make sure that your vehicle’s navigation system has the most accurate information available about streets/roads, points of interest, and business locations. The updates are provided by the GM Nav Disc Center at the ﬁrst and second anniversary dates of your vehicle’s delivery date. About four to six weeks before those anniversary dates, you will receive a post card from the GM Nav Disc Center reminding you that a free update is available. The center will request conﬁrmation of your mailing address either by having you contact the toll-free number, 1–877–NAV–DISC (1–877–628–3472), or the center’s website, www.gmnavdisc.com. After verifying your address you should receive the updated disc in about two weeks. After receiving the updated disc, replace the old disc in the navigation system. See “Installing the DVD Map Disc” and “Ejecting the DVD Map Disc” under Maps on page 271. Dispose of the old disc to avoid confusion about which disc is the most current. If you have any questions about the operation of the navigation system or the update process, call the GM Nav Disc Center or go to the center’s website. If you need any future updates or a replacement disc, because the current disc is lost, damaged, or needs to be updated, call the GM Nav Disc Center or order a new disc online. To order a disc, have your Vehicle Identiﬁcation Number (VIN) available. This helps the center make sure you receive the correct and most up to date DVD map disc for your vehicle. See Vehicle Identiﬁcation Number (VIN) on page 451 for more information. Database Coverage Explanations Coverage areas vary with respect to the level of map detail available for any given area. Some areas will feature greater levels of detail than others. If this happens, it does not mean there is a problem with the system. As the map DVD is updated, more detail may become available for areas which previously had limited detail. See Ordering Map DVDs on page 284. 284 Main Audio Menu e/ z(Audio/Adjust): Press this key to view the main audio screen. Navigation Audio System Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units. If sound equipment can be added, it is very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, radio, or other systems, and even damage them. Your vehicle’s systems may interfere with the operation of sound equipment that has been added. Your vehicle has a feature called Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 89 for more information. The audio system is operated using navigation system menus. The audio menus are explained in this section. 285 Display Presets on the Map: With this feature on, your audio system presets for the current audio source will be displayed on the left of the map screen. Touch ON to turn this feature on. You may also choose to turn this feature off. With this feature on, you can recall your preset radio stations from the map screen. You cannot store preset stations from the map screen. You must do this from the audio screen. See “Preset Station Menu” later in this section for more information on storing presets. Automatic Volume Control (AVC): The system has Bose AudioPilot® noise compensation technology. AudioPilot® monitors the level of noise in the vehicle and automatically increases or decreases the level of audio to keep it audible above the noise. To use AudioPilot®, press the ON screen button. To turn it off, press the OFF screen button. Preset Selection: Here you can program the audio system’s presets to recall your home settings by touching HOME. You can also recall the presets you use when traveling to another area by touching AWAY. See “Preset Station Menu” later in this section for more information on how to store preset stations. The Home and Away feature is not available for the XM™ Satellite Radio source, if equipped. 286 This feature is most effective at lower volume settings where background noise can affect how well you hear the music being played through your vehicle’s audio system. At higher volume settings, where the music is much louder than the background noise, there may be little or no adjustments by AudioPilot®. For additional information on AudioPilot®, please visit www.bose.com. 8(Clock): Touch this screen button to get to the CLOCK ADJUST menu. See “Clock Adjust Menu” later in this section for more information. SCREEN ADJUST: To adjust the brightness or contrast of the screen, touch SCREEN ADJUST to display the screen adjust menu. See “Screen Adjust Menu” later in this section for more information. SOUND: Touch this screen button to access the Sound menu. See “Sound Menu” later in this section for more information. DSP (Digital Signal Processing): Touch this screen button to access the DSP menu. See “Adjusting the Speakers” later in this section for more information. Clock Adjust Menu The following options are available from this menu: HOUR/MIN.: Touch the up or down arrows to increase or decrease the hour or minutes. If you touch and hold one of the arrows, the numbers will advance quickly. 12H/24H: Touch 12H to set the clock in standard time or 24H to set the clock in military time. 287 GPS TIME: The current GPS time will be displayed to the right of this screen button. Touch GPS TIME to set the navigation system time to match current GPS time. If the seconds for the present minute are greater than thirty when GPS TIME is selected, the clock will round up to the next minute. Daylight Saving Time: Touch this screen button to increase the time setting by one hour. Then touch GPS TIME to save the new setting. If the screen button is light blue, the daylight savings time feature is on. If the button is dark blue, the daylight savings time feature is off. TIME ZONE: The selected time zone will appear to the right of this screen button. Touch this screen button to toggle between time zones and select the desired one. The time of the selected zone will be displayed to the right of the GPS TIME screen button. To set the clock to the new setting, touch GPS TIME. If the system is not receiving GPS information, you can still set the time manually as described above but the GPS time and Daylight Saving Time features will not be available. Touch Return to go back to the previous menu. 288 Screen Adjust Menu The following options are available from this menu: K(Contrast): Touch the plus (+) or minus (−) signs to adjust the contrast of the screen. You will see the screen change. Touch SET to conﬁrm the setting. !(Brightness): Touch the plus (+) or minus (−) signs to adjust the brightness of the screen. You will see the screen change. Touch SET to conﬁrm the setting. AUTO: This setting automatically adjusts the contrast and brightness of the screen depending on exterior lighting conditions. DAY: This setting leaves the screen in day mode. Day mode is best suited for daylight conditions. NIGHT: This setting leaves the screen in night mode. Night mode is best suited for nighttime conditions. SCREEN OFF: Touch SCREEN OFF to turn off the screen. Press any hard key to turn the screen back on. SET: Touch SET to save your choices and exit the CLOCK ADJUST menu. Language Your vehicle has been set for the English language. If you wish to change the language, you must do so through the Driver Information Center (DIC). See Driver Information Center (DIC) on page 203 for more information. If the language is changed from English, a majority of the voice guidance prompts and screen text will change to the selected language. Remember, the menu screens will not match word-for-word as they appear in this manual. Playing the Radio PWR-VOL (Power-Volume): Press this knob to turn the audio and navigation systems on and off. Turn the knob to increase or decrease the volume to the audio system. «TUNE/SEEK ª: Press the up or down arrow to go to the next or previous station and stay there. BAND: Press this key to switch between AM, FM1, FM2, XM1, XM 2, or WX, if equipped. If you are on a map screen and press this key, the screen will not change but the audio source will. 289 Finding a Station FM1 audio source shown, other sources similar Press the BAND key to switch between AM, FM1, FM2, XM1, XM2, or WX, if equipped. Touch the desired audio source to select it. 290 Preset Station Menu Up to 36 stations, 6 AM, 6 FM 1, 6 FM 2, 6 XM 1, 6 XM 2, and 6 WX, if equipped, can be programmed for home and for away. To store presets, do the following: 1. Turn the audio system on. 2. Touch AM, FM, XM, or WX, if equipped, to display the desired source. The preset station menu will appear. 3. Tune to the desired station by using the TUNE/SEEK arrows. 4. Touch SOUND to set the bass, mid-range, treble, and DSP for your preset, if desired. See “Sound Menu” later in this section for more information. 5. Touch and hold one of the six numbered preset buttons for more than two seconds until you hear a beep. 6. Repeat the steps for each preset and source. SCAN: To scan stations, touch SCAN. The radio will go to a station, play for a few seconds, then go on to the next station. Touch SCAN again to stop scanning. To scan preset stations, touch and hold SCAN for two seconds. It will only scan the audio source it is in, with the exception of FM 1 and FM 2, which will both be scanned if in that source. Touch SCAN again to stop scanning. RDS (Radio Data System): See “Radio Data System (RDS)” later in this section for more information. MSG (Message): See “Radio Data System (RDS)” later in this section for more information. AutoSet: Touch AutoSet to replace currently stored preset stations with the strongest stations available in the immediate area. Touch AutoSet again to return to the original preset stations. SOUND: See “Sound Menu” following for more information. DSP: See “Adjusting the Speakers” later in this section for more information. Sound Menu Touch SOUND at the bottom of the main audio screen, source menu, or DSP menu to change the tone, DSP, if equipped, fade, and balance for all sources. The audio system has a separate setting for these features for each source preset. However, the audio system keeps one fade and one balance setting for all audio sources. 291 To adjust sound settings, do the following: 1. Touch the plus (+) or minus (−) signs to adjust treble, mid-range, and bass. 2. Touch the L for left or R for right to adjust the balance of the speakers. 3. Touch the F for front or R for rear to adjust the fade of the speakers. 4. Touch DSP to adjust your DSP, if equipped. See “Adjusting the Speakers” later in this section for more information. After adjustments are made, touch any source screen button. This will take you back to the preset station menu. Whenever you touch that screen button, the previously stored information you have entered for each preset station will be recalled. To adjust the tone for each preset, do the following: 1. Press the BAND key. 2. Touch AM, FM1, FM2, XM1, XM2, or WX, if equipped, to access the desired preset screen. 3. Touch SOUND. 4. Touch the plus (+) or minus (−) signs to adjust treble, mid-range, and bass. 5. Touch Return to exit. This will take you to the preset station menu. 6. Touch and hold one of the six preset screen buttons for more than two seconds until you hear a beep. Whenever you touch that preset for less than two seconds, the station and previously stored information you have entered for each preset station will be recalled. 7. Repeat the steps for additional presets. 292 Adjusting the Speakers DSP (Digital Signal Processing): The DSP feature is used to provide a choice of four different listening experiences. DSP can be used while listening to the audio system or the CD player. The audio system can store separate DSP settings for each source and preset station, except WX, which is always set to TALK. To save DSP settings for your preset stations, use the SOUND menu or touch DSP from the preset station menu to access the DSP menu. See “Sound Menu” listed previously in this section for more information. Touch DSP to change the following options: ON/OFF: Touch ON/OFF to turn DSP on and off. DRIVER SEAT: Touch this button to adjust the audio to give the driver the best possible sound quality. TALK: TALK makes spoken words sound very clear. Touch this button when listening to non-musical material such as news, talk shows, and sports broadcasts. SPACIOUS: Touch this button to make the listening space seem larger. SOUND: Touch SOUND to access the Sound menu. See “Sound Menu” listed previously in this section for more information. 293 The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: (cid:127) Seek to stations broadcasting the selected type of programming (cid:127) Receive announcements concerning local and national emergencies (cid:127) Display messages from radio stations (cid:127) Seek to stations with traffic announcements RDS: Touch RDS to use alternate RDS functions located in the preset menu. When you touch RDS, you will only have about ﬁve seconds to choose RDS ON/OFF, TA, MSG, PTY, or SEL PTY. If you do not make a selection, the system will return to the previous menu. Radio Data Systems (RDS) 294 If you are tuned to a station broadcasting RDS information, the station’s Program Service (PS) and Program Type (PTY) will replace the station’s frequency on the status line at the top of the display. After about ﬁve seconds, if available, the PTY will be replaced on the display by the station’s PTY name. The PTY and PTY name may be the same or different. If the audio system is tuned to a station that is not broadcasting RDS information, the station’s frequency will remain on the display. While RDS is on, the audio system will search for a stronger station in the network if a station gets too weak for listening. The RDS feature relies upon receiving speciﬁc information from RDS stations. These features will only work when RDS information is available. TA (Traffic): Touch TA to receive traffic announcements. The audio system will turn on the TA display. TA will appear on the display if the current station broadcasts traffic announcements. You may also receive traffic announcements from stations in the network related to the current station. If the current station does not broadcast traffic announcements, the audio system will seek to a station which will. When the audio system ﬁnds a station which broadcasts traffic announcements, it will stop. If no station is found, TA will turn off. While a traffic announcement plays, the audio system uses TA volume. To increase TA volume, touch the VOL button on your steering wheel or use the VOL up or down buttons during the announcement. See “Voice Guidance Volume Settings” under Setup Menu on page 243 for more information. 295 When a traffic announcement comes on the current radio station or a related network station, you will hear it even if the volume is muted or a CD is playing. If the audio system tunes to a related network station for a traffic announcement, it will return to the original station when the announcement is ﬁnished. If the CD player was being used, the CD will stay in the player and resume play at the point where it stopped. Touch RDS followed by TA again to turn TA off. MSG (Message): When RDS is on, if the current station has a message, MSG will appear on the display. Touch MSG from the preset menu to view the message. If the whole message does not appear on the display, parts of the message will appear every three seconds until the message is completed. Once the complete message has been displayed, MSG will disappear from the display until another new message is received. MSG will remain available to allow you to display the entire message again. 296 PTY: PTY allows you to seek only stations with types of programs you want to listen to. This button is used to turn on and off Program Type (PTY) features. With RDS on, touch RDS, followed by PTY. The PTY display will turn on. Touch RDS followed by this button again to turn the PTY display off. Select PTY (Select Program Type): With RDS and PTY on, touch RDS, then SEL PTY. The PTY menu will appear. Use the up and down arrows to select a PTY. Touch your PTY selection and the system will return you to the screen with the preset stations shown. See Steps 1 through 7 under “Preset Station Menu” to store the selected PTYs. The selected PTY is then stored on the preset. You can now touch the PTY preset to recall your settings. When the PTY display is on, press TUNE/SEEK and SCAN to ﬁnd radio stations of the PTY selected. The last PTY selected will be used for seek and scan modes. If a station with the selected PTY is not found, NONE FOUND will appear on the display. If both PTY and TA are on, the audio system will search for stations with traffic announcements and the selected PTY. PTY (Program Type) Presets: The six presets let you return to your favorite PTYs. These presets have factory PTY preset stations. See “RDS Program Type (PTY) Selections” later in this section. You can set up to 12 PTYs, 6 FM 1 and 6 FM2. To save a PTY preset, do the following: 1. Touch FM1 or FM2. 2. Touch RDS to enter the RDS menu. 3. Touch RDS ON/OFF to turn RDS on. 4. Touch PTY. 5. Touch SEL PTY and select the desired PTY from the list. 6. Touch and hold one of the six presets for more than two seconds until you hear a beep. Whenever you touch that numbered preset for less than two seconds, the PTY you set will return. 7. Repeat the steps for each preset. Once you have stored a PTY for each of your preset stations, you can recall a PTY preset by touching the preset station for less than two seconds. Then use TUNE/SEEK or SCAN to locate a station for that PTY selection. ALERT: This type of announcement warns of national or local emergencies. You will not be able to turn off alert announcements. Alert announcements will come on even if RDS mode is turned off. ALERT appears on the display when an alert announcement plays. The audio system uses TA volume during these announcements. To increase volume, touch the VOL button on your steering wheel or use the VOL up and down buttons during the announcement. See “Voice Guidance Volume Settings” under Setup Menu on page 243 for more information. When an alert announcement comes on the tuned radio station or a related network station, you will hear it even if the volume is muted or a CD is playing. If the audio system tunes to a related network station for an alert announcement, it will return to the original station when the announcement is ﬁnished. If the CD player is playing, the player will stop for the announcement and resume when the announcement is ﬁnished. 297 XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and in Canada. XM™ offers a large variety of coast-to-coast channels including music, news, sports, talk/weather (U.S. subscribers), and children’s programming. XM™ provides digital quality audio and text information that includes the channel name and number, song title, and artist name. A service fee is required in order to receive the XM™ service. For more information, contact XM™; in the U.S. at www.xmradio.com or call 1-800-852-XMXM (9696) or in Canada at www.xmradio.ca or call 1-877-GET-XMSR (438-9677). 298 INFO (Information): Touch INFO while in XM™ mode to retrieve various pieces of information related to the current song or channel. By touching INFO, you may retrieve four different categories of information: Artist Name/Feature, Song/Program Title, Channel Category, and other Additional Information that may be broadcast on that channel. Additional Information messages may only be available at certain times or on certain programs. If an Additional Information message is being broadcast on the tuned channel, INFO will appear on the display. Each of the four information types may have multiple pages of text. To reach a category, touch INFO repeatedly until the desired type is displayed. If there are multiple pages of text for the information selected type, the radio will automatically display all the pages for that type at a rate of about one page every three seconds before timing out and returning to the default display. You may override this feature by touching INFO to review all of the pages at your own pace. SCAN: Use this button to scan through the channels within a category or scan through the preset stations. To scan through the channels in a category, do the following: 1. Select a category by using the category arrows. 2. Once the desired category is displayed, touch SCAN. The radio will begin scanning within the chosen category. 3. Touch SCAN again to stop scanning. To scan through your preset stations, touch and hold SCAN. Touch SCAN again to stop scanning. XL (Explicit Language Channels): XL on the radio display, after the channel name, indicates content with explicit language. These channels, or any others, can be blocked at a customer’s request, by calling; in the U.S. 1-800-852-XMXM (9696) or in Canada 1-877-GET-XMSR (438-9677). Setting Program Type (PTY) Preset Stations SCATT(Category): Press the arrows to select a category. Once the desired category is displayed, press TUNE/SEEK to select the category and take you to the category’s ﬁrst station. If you want to go to another station within that category, press TUNE/SEEK once. Touch and hold one of the desired P1-P6 presets to store the selected station as a preset. If PTY times out and is no longer on the display, start again. 299 XM Radio Messages Radio Display Message Condition Action Required XM Updating Updating encryption code The encryption code in your receiver is being updated, and no action is required. This process should take no longer than 30 seconds. No XM Signal Loss of signal Your system is functioning correctly, but you are in a location that is blocking the XM signal. When you move into an open area, the signal should return. Loading XM Acquiring channel audio (after 4 second delay) Your radio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly. Channel Off Air Channel not in service Channel Unavail Channel no longer available This channel is not currently in service. Tune in to another channel. This previously assigned channel is no longer assigned. Tune to another station. If this station was one of your presets, you may need to choose another station for that preset button. No Info Artist Name/Feature, Song Title, CAT not available Artist, song title, and/or category information may not be available at this time on this channel. Your system is working properly. 300 Radio Display Message Condition Action Required Not Found No Information No channel available for the chosen category There are no channels available for the category you selected. Your system is working properly. No Text/Informational message available No text or informational messages are available at this time on this channel. Your system is working properly. XM Theftlocked Theft lock active XM Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM Receivr Hardware failure The XM receiver in your vehicle may have previously been in another vehicle. For security purposes, XM receivers cannot be swapped between vehicles. If you receive this message after having your vehicle serviced, check with the servicing facility. If you tune to channel 0, you will see this message alternating with your XM Radio 8 digit radio ID label. This label is needed to activate your service. If you receive this message when you tune to channel 0, you may have a receiver fault. Consult with your dealer. If this message does not clear within a short period of time, your receiver may have a fault. Consult with your retail location. 301 Six-Disc CD Changer With the compact disc changer, you can play up to six normal size discs continuously. When the radio is turned on, the changer will begin checking for discs. This will continue for up to one and a half minutes, depending on the number of discs loaded. You may hear noise, but this is normal. The CD changer is initializing. Press the CD hard key to access the six-disc CD changer screen. You can also use the system’s DVD player for single CD play once the map DVD is removed. See CD/DVD Player on page 305 for more information. If no CD is loaded in the CD/DVD Player and you press the CD hard key, the message “No CD Loaded” will appear on the display. 302 CD Changer Screen Once you access the CD changer screen, you can select one of the numbered buttons to go from one compact disc to another among those loaded in the CD changer and use the arrows to rewind or fast forward through the disc selected. The following features are also available from this screen: (cid:127) LOAD (cid:127) EJECT (cid:127) SCAN THE DISCS or SCAN THE TRACKS (cid:127) and RANDOM ALL or RANDOM DISC. The numbered buttons (1 through 6) represent the order of the discs loaded in the changer. If there are only two CDs loaded, buttons 1 and 2 will only be available to choose from. LOAD: Touch this button once each time you wish to load a CD into the changer. It may take up to 10 seconds for the changer to accept the CD into the slot depending on the changer initializing. Repeat this procedure for loading up to six discs. Press and hold the LOAD button until a beep is heard to put the changer in LOAD ALL mode. Once the Insert CD message is displayed, you can load all six discs, one after the other. r(Play): Touch this button to begin playing a CD. RANDOM DISC: Touch this button to hear the tracks in random, rather than sequential, order on the disc selected. Press the TUNE/SEEK hard key to randomly seek through the tracks on this disc. Touch RANDOM DISC again to turn off random play mode. SCAN TRACKS: Touch this button to hear the ﬁrst 10 seconds of each track on the selected disc. Touch this button again to stop scanning. The CD will mute while scanning. r(Rewind): Touch this button to rewind quickly through a track selection. EJECT: Touch this button once to eject the chosen CD. The chosen CD may be selected by ﬁrst touching one of the numbered buttons from 1 to 6. Repeat this procedure for ejecting up to six discs from the changer. If you press and hold the EJECT button until a beep is heard, The system will begin to eject all of the discs from the player. Once the CD is removed the next will come out until they are all ejected. 303 j(Pause): Touch this button to pause CD play. Touch it again to resume play or touch the play button. RANDOM ALL: Touch this button to hear the tracks on all of the discs in the CD changer in random, rather than sequential, order. Press the TUNE/SEEK hard key while RANDOM ALL is on to randomly seek within that disc. Touch RANDOM ALL again to turn off random mode. SCAN DISCS: Touch this button to hear the ﬁrst 10 seconds of ﬁrst track on each disc. Touch this button again to stop scanning. The CD will mute while scanning. [(Forward): Touch this button to fast forward quickly through a track selection. «TUNE SEEK ª: Press the up arrow on the TUNE/SEEK switch to seek to the next selection on the compact disc. If playing last track of disc, pressing the up arrow will seek to the ﬁrst track of the next disc. Press the down arrow to seek to the previous selection on the compact disc. If playing the ﬁrst track of disc, pressing the down arrow will seek to the last track on the selected disc. The sound will mute while seeking. RDS (Radio Data Systems): See “Radio Data Systems (RDS)” listed previously for information on this button. SOUND: See “Sound Menu (Tone, DSP, Fade and Balance)” for information on this button. DSP (Digital Signal Processing): See “Adjusting the Speakers” listed previously for information on this button. 304 CD Changer Errors CDX ERROR could be displayed for the following: (cid:127) The road is too rough. The disc should play when the road is smoother. (cid:127) The disc is dirty, scratched, wet or not loaded label side up. (cid:127) The air is very humid. If so, wait about an hour and try again. If any error occurs repeatedly or if an error cannot be corrected, please contact your GM dealer. If your audio system displays an error number, write it down and provide this information to your dealer when reporting the error. CD/DVD Player The player that is used for the navigation map DVD can also be used as a single music CD player or a video DVD player. CD Player To use the player as a single music CD player, you must ﬁrst remove the navigation map DVD. While playing a CD in the CD/DVD Player, the navigation system is not available. The message “The disc installed is not a map DVD” will appear on the display if any of the navigation hard keys are pressed. To remove the navigation map DVD and load a music CD, use the following steps: 1. Start the vehicle. 2. Press the TILT hard key until you hear a beep. This will open the faceplate of the system. 3. If one is loaded, the navigation map DVD will eject from the slot. 4. Gently remove the navigation map DVD from the slot and return it to its case. 305 5. Insert the music CD into the slot. The system will pull the CD into the player. 6. Press and release the TILT hard key to close the faceplate. Notice: Shifting out of PARK (P) with the system’s faceplate open will cause the faceplate to close automatically. This could cause damage to a CD, DVD or the system if it is partially loaded. Before shifting out of PARK (P), make sure that the DVD or CD is loaded properly. The vehicle must be shifted back into PARK (P) to close the faceplate. 306 CD Player Screen Once a music CD is loaded, the CD player menu will appear on the display. When using the system as a single CD player, the CD hard key will alternate between the CD player and the six-disc CD changer if CDs are loaded. r(Play): Touch this button to begin playing a CD. RANDOM: Touch this button to hear the tracks in random, rather than sequential, order on the disc. Touch RANDOM again to turn off random mode. SCAN TRACKS: Touch this button to hear the ﬁrst 10 seconds of each track on the disc. Touch this button again to stop scanning. The CD will mute while scanning. REPEAT TRACK: Touch this button to repeat the selected track. r(Rewind): Touch this button to rewind quickly through a track selection. j(Pause): Touch this button to pause CD play. Touch it again to resume play or touch the play button. [(Forward): Touch this button to fast forward quickly through a track selection. «TUNE SEEK ª: Touch the up arrow on the TUNE/SEEK hard key to seek to the next selection on the compact disc. If playing the last track of the disc, touching the up arrow will seek to the ﬁrst track of the disc. Touch the down arrow to seek to the previous selection on the compact disc. If playing the ﬁrst track of the disc, touching the down arrow will seek to the last track of the disc. The sound will mute while seeking. DVD Player To use the player as a video DVD player, you must ﬁrst remove the navigation map DVD or music CD. While playing a video DVD, the navigation system is not available. The message “The disc installed is not a map DVD” will appear on the display if any of the navigation hard keys are pressed. This feature will not operate unless the vehicle is in PARK (P). 307 Playing a DVD There are three ways to play a DVD depending on which screen you are on. They are the following: (cid:127) Once a DVD is inserted, the system will (cid:127) automatically play the DVD. If you are on a map screen, touch the DVD source button. (cid:127) From the audio screen, press the DVD hard key. To remove the navigation map DVD and load a video DVD, use the following steps: 1. With the vehicle in PARK (P) and the vehicle running, press the TILT hard key until a beep is heard. The faceplate of the system will open. 2. If a map DVD or a music CD is loaded, the system will automatically eject it. Gently remove it from the slot and return it to its case. 3. Load the video DVD into the slot. The system will pull the DVD into the player. 4. Press and release the TILT hard key to close the faceplate. Notice: Shifting out of PARK (P) with the system’s faceplate open will cause the faceplate to close automatically. This could cause damage to a CD, DVD or the system if it is partially loaded. Before shifting out of PARK (P), make sure that the DVD or CD is loaded properly. The vehicle must be shifted back into PARK (P) to close the faceplate. Once the faceplate is closed and a video DVD is loaded, the system will automatically play the DVD. 308 DVD Menu Options To display the menu choices while a DVD is playing, touch anywhere on the screen and the menu will appear. IMAGE: Touch this button to either start playing a DVD or to remove the DVD menu screen. AUDIO PROGRAM: Touch this button to change the audio language heard. VIEWING ANGLE: Touch this button to adjust the viewing angle of the DVD. Some DVDs allow you to change the camera angle. This may not be available on all DVDs. Depending on the type of DVD you are using, this button may or may not be available. SUBTITLE: Touch this button to playback the video with subtitles. This may not be available on all DVDs. Depending on the type of DVD you are using, this button may or may not be available. SCREEN ADJUST: Touch this button to adjust the brightness, contrast and red/green color adjustments. CURSOR: Touch this button to access the left/right and up/down cursors on the screen. The cursors allow you to navigate menu options on the screen. MENU: Touch this button to access the DVDs menu options. Depending on the type of DVD you are using, this button may or may not be available. Touch the button labeled one, two or blank to change the image size displayed on the screen. 309 TITLE: Touch this button to display the title of the DVD. Depending on the type of DVD you are using, this button may or may not be available. If TITLE is available, this button will allow you to navigate through chapters or the DVD features. Once the appropriate title or track has been selected, press the Return button then the IMAGE button on the DVD menu to view the movie in full screen. 310 SETTING: Touch this button to adjust the following: (cid:127) LANGUAGE PREFERENCES (cid:127) PARENTAL LOCK Under LANGUAGE PREFERENCES, you can select different languages for AUDIO, SUBTITLE and DVD MENUS. 1. To change languages, ﬁrst select the option you wish to change. 2. Select a language from the list given. 3. Touch RETURN to end out the menu. Your language is now saved. Under PARENTAL LOCK, you can select SET RATING LIMIT and SET PIN. To SET RATING, ﬁrst touch the button. Then, make your selection. Touch RETURN to end out the menu. Your selection is now saved. To use PARENTAL LOCK, ﬁrst touch the button. Then, enter a four-digit numeric password. Touch RETURN to end out the menu. SEARCH: Touch this button to search to a certain scene on the DVD. Depending on the type of DVD you are using, this button may or may not be available. r(Rewind): Touch this button to rewind through a scene during playback. r(Resume): Touch this button to resume playing a DVD. c(Stop): Touch this button to stop the DVD. j(Pause): Touch this button to pause the DVD. [(Forward): Touch this button to advance rapidly during playback. L(Frame Advance): Touch this button to advance by chapter during playback. Radio Personalization with Home and Away Feature With this feature, you can recall the latest audio system settings as adjusted the last time your vehicle was operated. This feature allows two different drivers to store and recall their own audio system settings. The settings recalled by the audio system are determined by which transmitter (1 or 2) was used to enter the vehicle. The number on the back of the transmitter corresponds to driver 1 or to driver 2. The audio system settings will automatically adjust to where they were last set by the identiﬁed driver. The settings can also be recalled by brieﬂy pressing the MEMORY seat switches 1 or 2 located on the driver’s door. Your audio system can store HOME and AWAY preset stations. HOME and AWAY preset stations allow you to use one set of preset radio settings in the area where you live, and another set when you go out of town. That way, you will not need to reprogram your preset stations every time you travel. 311 To select HOME and AWAY preset stations, do the following: 1. With the audio system on, touch the Audio hard key and turn the audio system off. 2. Touch the HOME or AWAY button from the main audio screen. The next time the audio system is turned on, the system will recall the last active preset selection. When battery power is removed and later applied, you will not have to reset your home audio system preset stations because the audio system remembers them. However, you will have to reset your away radio preset stations. Voice Recognition The navigation system’s voice recognition allows for hands-free operation of navigation and audio system features. Voice recognition can be used when the ignition is on or when Retained Accessory Power (RAP) is active. This feature only works if the map DVD is inserted and I AGREE has been selected. If you try to use voice recognition without the map DVD inserted, the system will display “Please insert the navigation map DVD to use the voice recognition feature.” To use navigation voice recognition, do the following: 1. Press the talk symbol steering wheel control and release it, when you hear a beep. The audio system, if on, will mute. 2. Clearly state one of the commands listed on the following pages. For example, say “FM1”. 3. The system will tell you the command being implemented. For example, the system will say “FM1 Radio” and change the audio system to the FM1 source. 312 You can end voice recognition by not speaking any commands. After about ﬁve seconds of silence, the system will automatically cancel voice recognition. At times, the system may not understand a spoken command. If this happens, try saying the command again. If a spoken command is not available, the system will provide feedback based on availability. While using voice recognition, make sure to keep interior noise levels to a minimum. Otherwise, the system might not recognize voice commands. The system will only recognize commands spoken in English. Voice Recognition Commands The following list shows all of the voice commands available for the navigation system with a brief description of each. To use the voice commands, refer to the instructions listed previously. Help Commands These commands are universal and will enable you to use the help prompts available from the system. Map Help: This command will enable the system to provide the available commands for the map screen. Destination Help: This command will enable the system to provide the available commands for entering a destination. Guidance Help: This command will enable the system to provide the available commands for the guidance method. Radio Help: This command will enable the system to provide the available commands for the radio. Disc Help: This command will enable the system to provide the available commands for the CD changer. 313 Radio Commands Radio: This command will change the audio system to the next radio audio source. AM: This command will change the audio system to the AM audio source. FM1: This command will change the audio system to the FM1 audio source. FM2: This command will change the audio system to the FM2 audio source. XM1: This command will change the audio system to the XM1 audio source. XM2: This command will change the audio system to the XM2 audio source. CD Changer: This command will change the audio system to the CD changer audio source. WX, Weather Band: These commands will change the audio system to the weather band audio source. Power On, Audio On: These commands will turn the system’s power on. Power Off, Audio Off: These commands will turn the system’s power off. Seek Up: This command will cause the selected audio source to seek up to the next strongest signal. Seek Down: This command will cause the selected audio source to seek down to the next strongest signal. Stop Scan: This command will cause the audio source to stop scanning for the next strongest signal. CD Changer Commands Track Up: This command will cause the CD changer to skip up to the next track. Previous Track, Track Down: This command will cause the CD changer to go to the previous track. 314 Screen Commands Screen Day Mode, Day Mode On: These commands will adjust the system’s screen setting to the day mode. Screen Night Mode, Night Mode On: These commands will adjust the system’s screen setting to the night mode. Screen Auto Mode, Auto Mode On: These commands will adjust the system’s screen setting to auto mode. Screen Off: This command will turn the system’s screen display off. Position Commands Current Position, Current Location, Show Current Position, Show Current Location: These commands will cause the system to display the vehicle’s current location on the map screen. Map: This command will cause the system to display the map screen. Map Commands Zoom In: This command will cause the system to zoom in when on the map screen. Zoom Out: This command will cause the system to zoom out when on the map screen. Maximum Scale: This command will cause the system to zoom out to the maximum available map scale when on the map screen. Minimum Scale: This command will cause the system to zoom in to the minimum available map scale when on the map screen. Heading Up, Change to Heading Up: These commands will cause the system to display the Vehicle Up heading when on the map screen. The map scale should be set for under 2 miles (4 km). North Up, Change to North Up: These commands will cause the system to display the North Up heading when on the map screen if the map scale is set to 2 miles (4 km) or less. 315 Map Direction, Change Map Direction: These commands will cause the system to change the vehicle’s direction from North Up to Heading Up or Heading Up to North Up on the map screen if the map scale is set to 2 miles (4 km) or less. Mark, Mark This Point: These commands will cause the system to mark the location as a memory point while on the map screen. Destination Commands Home, Go Home: These commands will cause the system to enter the Home destination, if one is set. Go To Starting Point, Previous Starting Point: These commands will cause the system to enter the last available starting point as a destination. Guidance Commands Repeat Guidance, Repeat Voice: These commands will cause the system to repeat the last available voice prompt guidance command if a destination has been set. Louder: This command will cause the system to increase the volume of the navigation voice prompts if a destination has been set. Softer: This command will cause the system to decrease the volume of the navigation voice prompts if a destination has been set. Voice Guidance Off: This command will cause the system to turn off the navigation voice prompts if a destination has been set. Voice Guidance On: This command will cause the system to turn on the navigation voice prompts if a destination has been set. Open Guidance, Open Guidance Screen, Open Guide, Open Guide Screen: These commands will cause the system to open the Guidance Appearance menu if a destination has been set. Close Guidance, Close Guidance Screen, Close Guide, Close Guide Screen: These commands will cause the system to close the Guidance Appearance menu if a destination has been set. 316 Arrow Guidance, Arrow Guide, Change To Arrow Guidance, Change To Arrow Guide: These commands will cause the system to change to Arrow Guidance screen view in the Guidance Menu if a destination has been set. Turn List Guidance, Turn List Guide, Change to Turn List Guidance, Change to Turn List Guide: These commands will cause the system to change to Turn List Guidance screen view in the Guidance Menu if a destination has been set. Entire Route, Entire Route Map, Route Overview: These commands will cause the system to display the entire route if a destination has been set. Reroute: This command will cause the system to generate an alternate route to a set destination while on a planned route. Detour, Detour Entire Route: These commands will cause the system to activate the detour feature when driving a planned route. Delete Destination, Cancel Destination: These commands will cancel a destination if one has been set. Next Waypoint Map: This command will cause the system to display the map view of the next waypoint location if one has been set. First Waypoint Map: This command will cause the system to display the map view of the ﬁrst waypoint location if one has been set. Second Waypoint Map: This command will cause the system to display the map view of the second waypoint location if more than one waypoint has been set. Third Waypoint Map: This command will cause the system to display the map view of the third waypoint location if more than two waypoints have been set. Fourth Waypoint Map: This command will cause the system to display the map view of the fourth waypoint location if more than three waypoints have been set. Fifth Waypoint Map: This command will cause the system to display the map view of the ﬁfth waypoint location if more than four waypoints have been set. Destination Map: This command will cause the system to display the map view of the ﬁnal destination location if one has been set. 317

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Cadillac XLR Owners Manual