1998 Cadillac Deville Owners Manual

1-48

5. Pull the rest of the lap belt all the way out of the

retractor to set the lock.

6.

7.

To tighten the belt, feed the lap belt back into the retractor while you push down on the child restraint. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt. Push and pull the child restraint in different directions to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt for an adult will move freely again and be ready to work or larger child passenger.

1-49

Larger Children

If you have the choice, a child should sit next to a window so the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. Accident statistics show that children are safer if they to use the are restrained in the rear seat. But they need safety belts properly. a Children who aren’t buckled up can be thrown out in

a crash.

a Children who aren’t buckled up can strike other

people who are.

Children who have outgrown child restraints should wear the vehicle’s safety belts.

1-50

I

Never do this.’ Here two children are wearing the same belt. The belt -can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time.

@ What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?

A: Move the child toward the center of the vehicle, but

be sure that the shoulder belt sti€l,is on the child’s shoulder, so that in a crash the child’s upper body would, have the restraint that belts provide. If the child is so small that the shoulder belt is still very close to the child’s face or neck, you might want to place the child in the center seat position, the one that has only a lap belt.

1-51

A CAUTION:

in a seat that has a

Never do this. Here a child is sitting lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries.

Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt- force to the child’s pelvic bones in a crash.

fasten, your

Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt isn’t long enough to you go dealer will order you an extender. It’s free. When in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. The extender will be just for you, and just for the seat in your vehicle that you choose. Don’t let someone else use it, and use it only for the seat it is made to fit. To wear it, just attach it to the regular safety belt. Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Torn or frayed safety belts may not protect you in crash. They can rip apart under impact forces. torn or frayed, get a new one right away. Also look for any opened or broken air bag covers, and have them repaired or replaced. (The air bag system does not need regular maintenance.)

If a belt is

Replacing Restraint System Parts After a Crash If you’ve had a crash, do you need new belts? After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be during a more severe crash, then you need new belts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt wasn’t being used at the time of the collision. If an air bag inflates, you’ll need to replace air bag system parts. See the part on the air bag system earlier in this section.

if worn

1-53

6 NOTES

1-54

b NOTES

1-55

b NOTES

1-56

Features and Controls

Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell working properly -- and what to do if you have a problem.

you if everything is

2-2 2-4 2-7 2- 10 2- 14 2-15 2-17 2- 18 2-18 2-20 2-2 1 2-23 2-26 2-28 2-3 1 2-3 1

Keys Door Locks Remote Keyless Entry (RKE) System Trunk Theft Theft-Deterrent System (If Equipped) PASS-Key’II New Vehicle “Break-In’’ Ignition Positions Starting Your Engine Engine Coolant Heater (If Equipped) Automatic Transaxle Operation Parking Brake Shifting Into PARK (P) Shifting Out of PARK (P) Parking Over Things That Burn

2-32 2-32 2-33 2-34 2-35 2-42 2-46 2-48 2-54 2-56 2-56 2-5 8 2-59 2-62 2-67 2-79

Engine Exhaust Running Your Engine While You’re Parked Windows Tilt Wheel Turn SignaUMultifunction Lever Exterior Lamps Interior Lamps Mirrors Storage Compartments Sun Visors Cellular Telephone (Option) Astroroof (Option) Universal Transmitter (Option) Instrument Panel Warning Lights, Gages and Indicators Driver Information Center (DIC)

Keys A CAUTION:

Leaving young children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate power windows or other controls or even make the vehicle move. If they turned the ignition to RUN and moved the shift lever out of PARK (P), that would release the parking brake. Don’t leave the keys in a vehicle with young children.

2-2

The square key is for the ignition only. It has a resistor pellet which is part of the vehicle’s PASS-Key% system.

The oval key doors and all

is for the other locks.

When a new vehicle is delivered, the dealer removes the plug from the door key. The plug has a code on it that tells the dealer or a qualified locksmith how to make extra keys. The ignition key has a bar code tag attached to it rather than a knock out plug. Your dealer or qualified locksmith can make extra ignition keys reading the bar code tag. Keep the bar code tag and the door key plugs in a safe place. If you lose your keys, you will be able to have new ones made using the plug or bar code tag.

by

NOTICE:

Your vehicle has a number of new features that can help prevent theft. You can have a lot of trouble getting into your vehicle if you ever lock your keys inside and you may have to damage your vehicle to get in. Be sure you have extra keys.

\ .

2-3

If your vehicle has the optional theft-deterrent system, you must unlock the doors with the key or remote keyless entry transmitter to avoid setting off the alarm.

Door Locks 1 A. CAUTION: Passengers -- especially children -- can easily

Unlocked doors can be dangerous.

open the doors and fall out. When a door is locked, the inside handle won’t open it. Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. This may not be so obvious: You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked. Wear safety bel properly, lock your doors, and you will be far better off whenever you drive your vehicle.

.ts

There are several ways to lock and unlock your vehicle. From the outside, use either the door key or the remote keyless entry transmitter.

Rotate the manual lock lever forward to lock the door from the inside. To unlock the door, rotate the lever rearward.

2-4

Central Door Unlocking System Your vehicle will have this feature if it is equipped with the optional theft-deterrent system. When unlocking either front door, you can unlock the other doors by holding the key in the turned position for a few seconds or by quickly turning the door key twice in the lock cylinder. Power Door Locks

Press the power door lock to lock or unlock all the doors ‘at’once. The rear power door locks provide a lock only function as a convenience feature., For safety reasons, they will not unlock the doors.

’

Automatic Door Locks Close your doors and turn on the ignition. Every time you move the’ shift lever out of PARK (P), all of the doors will lock. The doors will unlock every time you stop the vehicle and move the shift lever into PARK (P). is not in - If someone needs to get out while your vehicle the manual or power PARK (P), have that person use lock. When the door is closed again, it will not lock automatically. Use the manual or power door again. If you need to lock the doors before shifting out of PARK (P), use the manual or power lock button to lock the doors. Programmable Automatic Door Locks (If Equipped) With the ignition in programmed through prompts displayed by the Driver Information Center (DIC). These prompts allow the driver to choose various lock settings. For programming information, see “Programmable, Memory and Personalization Features” later in this section.

RUN, the door locks can be

lock to lock the

2-5

Rear Door Security Locks

Your vehicle is equipped with rear door security locks that help prevent passengers from opening the rear doors of your vehicle from the inside. To use this lock:

1. Move the lever on the door all the way up to the

ENGAGED position.

2. Close the door. 3. Do the same thing to the other rear door lock. The rear doors of your vehicle cannot be opened from the inside when this feature is in use.

When you want to open a rear door when the security lock is on: 1. Unlock the door from the inside. 2. Then open the door from the outside. To cancel the rear door lock: 1. Unlock the door and open it from the outside. 2. Move the lever all the way down. 3. Do the same for the other rear door. The rear door locks will now work normally. Anti-Lockout Feature Leaving your key in any ignition position with any door open will disable the use of the power door lock switches as well as the lock button on the remote keyless entry transmitter. If you close the doors, you can lock It is them using the remote keyless entry transmitter. always recommended that you remove the ignition key when locking your vehicle. Note that the anti-lockout feature can be overridden by holding the driver's power door lock switch for three seconds or longer.

2-6

Leaving Your Vehicle If you are leaving the vehicle, open the door, set the locks from the inside, get out and close the door. Remote Keyless Entry (RKE) System

With this feature, you can lock and unlock the doors, unlock the trunk, open the fuel door and turn on your vehicle’s interior lamps from about 10 feet (3 m) away using the remote keyless entry transmitter supplied with your vehicle.

Your remote keyless entry transmitter operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. The range of this system is about 10 feet (3 m). At times you may notice a decrease in range. This is normal for any remote keyless entry transmitter. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: Check to determine if battery replacement is necessary. See the instructions that follow. Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. If you’re still having trouble, see your dealer or a qualified technician for service.

Operation

When you press this symbol to unlock the driver’s door, the parking lamps on your vehicle will blink twice. (You can program your vehicle so the parking lamps will not flash. For more information, see “LocMUnlock Confirmation” later in this section.) Pressing this symbol again within five seconds will unlock the other doors. Pressing this symbol will also disarm the optional theft-deterrent system and turn on the interior lamps at night. 8 When you press this symbol to lock the doors, the parking lamps will blink once. (You can program your vehicle so the parking lamps will not flash. For more information, see “LocMUnlock Confirmation” later in this section.) This also arms the optional theft-deterrent system.

Press this symbol to open the trunk. (The valet lockout button must be off for this feature to work.)

Press this button to open the fuel door.

(The valet lockout button must be off for this feature to work.)

the transmitter, you

The remote keyless entry transmitter can also be used to recall the memory settings for up to two drivers. For more information, see “Memory Seat and Mirrors” in the Index. Note that pressing the transmitter buttons numerous times (approximately 500 times) out of the vehicle’s operating range may cause the transmitter not to work. Replacing the battery and pressing the transmitter buttons 10 or more times out of range will also cause the transmitter not to work. To reset must be within the vehicle’s operating range. Press and hold the trunk button, and within one second, press and hold the lock button. Continue to hold both buttons for approximately three seconds. See your dealer for service if your transmitter still doesn’t work properly. Matching Transmitter(s) To Your Vehicle Each remote keyless entry transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your dealer. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can have only two transmitters matched to it.

2-8

Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery.

I NOTICE:

When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter.

1. Use the round end of the door key or a coin to pry

open the transmitter.

2. Once the transmitter is separated, use a pencil to

remove the old battery. Do not use a metal object.

2-9

Trunk

It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid:

Make sure all windows are shut. Turn the fan on your heating or cooling system to its highest speed with the setting on AUTO or ECON and the temperature between 65” F (18” C) and 85” F (29” C). That will force outside air into your vehicle. See “Comfort Controls” in the Index. If you have air outlets on or under the instrument panel, open them all the way.

See “Engine Exhaust’’ in the Index.

3. Remove and replace the battery. Insert the new

battery as the instructions under the cover indicate.

4. Snap the transmitter back together tightly to be sure

no moisture can enter.

5. Resynchronize the transmitter by pressing and

holding the lock and unlock buttons for about eight seconds within range of the vehicle. Once the transmitter is resynchronized, the horn will chirp and the exterior lamps will flash once.

2-10

Trunk Lock Release

Trunk Storage System (Option)

To use this feature, your vehicle must be in PARK (P) and the valet lockout button must be off. Press the trunk release button, located on the headlamp control panel on the left side of the instrument panel, to open the trunk.

You can also press the trunk button on keyless entry transmitter to access the trunk compartment. To disable the use of this feature, see “Valet Lockout Button’’ in the Index.

the remote

If equipped, the trunk storage system can be used to organize many different items inside the trunk. The cover (A) is located on top of the spare tire cover (B).

2-11

To install the storage system: 1. Pull the carpeting from the floor of the trunk. Turn the retainer (center dial) on the compact spare tire cover to the left to remove it.

2. Place the trunk storage system on the center of the

trunk floor.(the cut out portion of the storage system should be facing the rear of the vehicle).

3. Open the storage system by pulling up on the handle

located in the carpeted area. This allows the unit to fold up into place. Fold the divider walls open and move them into the retention slots.

4. Remove the rectangular access panel from the floor

of the storage system. The access panel should unsnap'by hand.

5. Center the storage system access hole over the area

where the spare tire is secured by the retainer. Position the storage system as needed and then secure it with the retainer.

6.; Replace the access panel. 7. Attach the removable net to the slots located on the

front of the divider walls and attach the hooks to the holes on each side of the storage system.

4.

2-12

Once in place, the storage system can be moved forward or rearward for convenience and easy access of stored items. The following steps explain how to remove the storage system for cleaning or in case you need to access the spare tire. Follow all of these steps if the storage system is in the closed position. Begin with Step 2 if the system is already open. 1.

trunk

the handle

Open the storage system by pulling up on located in the carpeted area. This allows the unit to fold up into place. Fold the divider walls open and move them into the retention slots. Remove the rectangular access panel from the floor of the storage system. The access panel should unsnap by hand. Center the storage system access hole over where the spare tire is secured by the retainer. Position the storage system as needed and then remove the retainer (turn the retainer to the left to remove it). Replace the access panel and remove the storage system.

the &ea

3.

2.

Trunk Lid Automatic Pull-Down Feature

/A

Your car has an automatic pull-down feature that helps close the trunk electronically. Your fingers can be trapped under the trunk lid as it goes down. Your fingers could be injured, and you would need someone to help you free them. Keep trunk lid as you close your fingers away from the it and as it is going down.

With the automatic pull-down feature, you never have to slam the trunk lid in order to close the trunk. Instead, it is nearly shut -- the gently lower the trunk lid until automatic pull-down unit will take over and lock the trunk firmly.

/ -

A. Trunk Lid B. Lever If for some reason me trunk lid (A) will not close, it may be because the trunk pull-down unit was accidently bumped. Even though the trunk lid remains open, the motor from the pull-down unit has already cycled down. If this happens, press the lever (B) on the trunk lid. The pull-down unit motor will reset itself allowing the trunk lid to close when lowered.

2-13

Theft Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. However, there are ways you can help. Key in the Ignition If you leave your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves -- so don’t do it. When you park your vehicle and open the driver’s door, you’ll hear a chime reminding you from the ignition and take it with you. Always do this. Your steering wheel will be locked, and so will your ignition and transaxle. And remember to lock Parking at Night Park in a lighted spot, close all windows and lock your vehicle. Remember to keep your valuables out of sight. Put them in a storage area, or take them with you.

to remove your key

the doors.

Parking Lots If you park in a lot where someone will be watching it up and take your keys. your vehicle, it’s best to lock But what if you have to leave your ignition key?

lit area.

If possible, park in a busy, well Put your valuables in a storage area, like your trunk or glove box. Be sure to close and lock the storage area. Close all windows. Lock the glove box. Lock all the doors except the driver’s. Then take the door key and remote keyless entry transmitter with you.

2-14

Theft-Deterrent System (If Equipped) Remember, the theft-deterrent system won’t activate if you lock the doors with a key or use the manual door lock. It activates only if you use a power door lock switch or the remote keyless entry transmitter. To

If the ignition is off and any door is open, the SECURITY light will flash, reminding you to activate the system.

SECURITY

The light will also flash if the battery has been disconnected and reconnected. To arm the system, do the following: 1. Open the door. 2. Lock the door using the power door lock or the

remote keyless entry transmitter. The SECURITY light should come on and stay on.

3. Close all the doors. The SECURITY light should go

off within about 30 seconds.

The horn will sound and the lamps will flash for about 30 seconds when the door or trunk is opened without the key or the remote keyless entry transmitter. The horn also sounds if the locks are damaged.

avoid activating the alarm by accident: Always unlock a door with a key or use the remote keyless entry transmitter. (Pressing the unlock button on the remote keyless entry transmitter disables the theft-deterrent system.) Unlocking a door any other way will activate the alarm. Cycling the ignition without disarming the theft-deterrent system will also activate the alarm. The vehicle should be locked with the door key after the doors are closed if you don’t want to activate the theft-deterrent system.

If you activate the alarm by accident, unlock any door with your key. You can also turn off the alarm by using the unlock button of the remote keyless entry transmitter. The alarm won’t stop if you try to unlock a door any other way.

2-15

Testing the Alarm 1. From inside the vehicle, roll down the window, then

get out of the vehicle, keeping the door open.

2. From outside of the vehicle, with the door open, lock the vehicle using the power door lock or the remote keyless entry transmitter and close the door. Wait 30 seconds until the SECURITY light goes off.

3. Reach in and unlock the door using the manual lock

and open the door. The horn will sound and the headlamps will flash.

If the alarm does not sound when it should, check to see if the horn works. The horn fuse may be blown. To replace the fuse, see “Fuses and Circuit Breakers” in the Index. If the fuse does not need to be replaced, you may need to have your vehicle serviced. To reduce the possibility of theft, always activate the theft-deterrent system when leaving your vehicle.

Valet Lockout Button

Pressing the valet button located inside the glove box will disable the use of the power trunk, fuel door and garage door openers. Pressing this button again will make these features reusable. Locking the glove box with the door key will also help to secure your vehicle.

Note that the remote keyless entry transmitter can’t be used to open the trunk or fuel door if the valet button is on.

2-16

PASS-Kev@ I1

Your vehicle is equipped with the PASS-Key 11 theft-deterrent system. PASS-Key I1 is a passive system. The system is armed when the key is removed from the ignition.

PASS-Key I1 uses a resistor pellet in the ignition key that is read by the system in your vehicle. If the key resistor matches the code stored in the vehicle system, the vehicle’s fuel and starting systems will be enabled. If an incorrect key is used, the vehicle’s fuel and starting systems are disabled for three minutes. Additional attempts during this lockout period will not start the car, even with the correct key.

If the engine does not start and the STARTING DISABLED, REMOVE KEY message is displayed in the Driver Information Center, your key should be checked for damage. Starting may be attempted with an undamaged key immediately. See your dealer or a locksmith for key service. If the STARTING DISABLED, REMOVE KEY and WAIT 3 MINUTES messages are displayed, the key should be cleaned. After three minutes, try again. A START CAR message will appear at this time. If the try a engine still does not start, wait three minutes and duplicate key. At this time, fuses should be checked (see “Fuses and Circuit Breakers” in the Index). If the engine does not start with the duplicate key, your vehicle needs service. See your dealer for service. If the THEFT SYSTEM PROBLEM, CAR MAY NOT START message is displayed during vehicle operation, a fault has been detected in the system. This means the PASS-Key I1 system is disabled and is not protecting the vehicle. The vehicle usually restarts. See your dealer for service. If an ignition key is lost or damaged, see your dealer or a locksmith to have a new key made.

2-17

New Vehicle 66Break-In”

Ignition Positions

NOTICE:

Your vehicle doesn’t need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines:

Don’t drive at any one speed -- fast or slow -- for the first 500 miles (805 km). Don’t make full-throttle starts. Avoid making hard stops for the first 200 miles (322 km) or so. During this time your new brake linings aren’t yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. Don’t tow a trailer during break-in. See “Towing a Trailer’’ in the Index for more information.

2-18

With the ignition key in the ignition switch, you can turn the switch to five different positions. ACCESSORY (A): This position lets you use things like the radio and the windshield wipers when the engine is off. To get into ACCESSORY, push in the key and turn it toward you. The steering wheel will remain locked, just as it was before you inserted the key.

LOCK (B): Before you put the key in, the ignition will be in LOCK. This is the only position in which you can remove the key. This position locks the ignition, steering wheel and transaxle. It’s a theft-deterrent feature.

Retained Accessory Power (RAP) The following accessories on your vehicle may be used for up to 10 minutes after the ignition key is turned from RUN to OFF:

Radio Power Windows Astroroof

Power to these accessories stops after 10 minutes or if any door is opened. If you want power for another 10 minutes, turn the ignition key to RUN, then back to OFF, then to LOCK. Always leave your key in LOCK when using RAP. If you leave your key in any other position than LOCK, your battery will discharge prematurely.

NOTICE:

If your key seems stuck in LOCK and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard. But turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of this works, then your vehicle needs service.

OFF (C): This position lets you turn off the engine but still turn the steering wheel. It doesn’t lock the steering wheel like LOCK does. Use OFF if you must have your vehicle in motion while the engine is off (for example, if your vehicle is being pushed). RUN (D): This is the position for driving. START (E): This position starts the engine.

2-19

Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position -- that’s a safety feature. To restart when you’re already moving, use NEUTRAL (N) only.

NOTICE:

NOTICE:

Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor.

Don’t try to shift to PARK (P) if your Cadillac is moving. If you do, you could damage the transaxle. Shift to PARK (P) only when your vehicle is stopped.

2. If it doesn’t start right away, hold your key in

START for about three seconds at a time until your engine starts. Wait about 15 seconds between each try to help avoid draining your battery or damaging your starter.

1. Without pushing the accelerator pedal, turn your

ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm.

2-20

Engine Coolant Heater (If Equipped)

3. If your engine still won’t start (or starts but then

stops), it could be flooded with too much gasoline. Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in START for about three seconds. If the vehicle starts briefly but then stops again, do the same thing.

I NOTICE:

Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you don’t, your engine might not perform properly. If you ever have to have your vehicle towed, see the part of this manual that tells how to do it without damaging your vehicle. See “Towing Your Vehicle’’ in the Index.

In very cold weather, 0” F (- 18 O C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged four hours prior to starting your vehicle.

in a minimum of

2-21

4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you don’t, it could be damaged.

How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your your dealer in the area where you’ll be parking vehicle. The dealer can give you the best advice for that particular area.

To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. 3. Plug it into a normal, grounded 110-volt AC outlet.

Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord won’t reach, use a heavy-duty three-prong extension cord rated for at least 15 amps.

2-22

Automatic l’ransaxle Operation The automatic transaxle may have either a shift lever located on the steering column or on the console between the seats. There are several different positions for the shift lever.

Console Shifter

Column Shifter

PARK (P): This position locks the front wheels. It’s the best position to use when you start the engine because your vehicle can’t move easily.

A CAUTION:

It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your -vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See “Shifting Into PARK (P)” in the Index.. If you’re pulling a trailer, see “Towing a Trailer” in the Index.

2-23

Ensure the shift lever is fully in PARK (P) range before starting the engine. Your vehicle has a Brake-Transaxle Shift Interlock (BTSI). You have to fully apply your regular brakes befure you can shift from PARK (P) when the ignition key is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever -- push the shift lever all the way into PARK (P) and release the shift lever button on the floor shift console models as you maintain brake application. Then move the shift lever into the gear you wish. (Press the shift lever button before moving the shift lever on floor shift console models.) See “Shifting Out of PARK (P)” in this section. REVERSE (R): Use this gear to back up.

NOTICE:

Shifting to REVERSE (R) while your vehicle is moving forward could damage your transaxle. Shift to REVERSE (R) only after your vehicle has stopped.

Also use this gear to rock your vehicle back and forth get out of snow, ice or sand without damaging your transaxle. See “If You’re Stuck in Sand, Mud, Ice or Snow” in the Index for additional information. 2-24

to

NEUTRAL (N): In this position, the engine doesn’t connect with the wheels. To restart when you’re already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when your vehicle is being towed.

Shifting out of PARK (P) or NEUTRAL (N) while your engine is “racing” (running at high speed) is dangerous. Unless your foot is firmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Don’t shift out of PARK (P) or NEUTRAL (N) while your engine is racing.

NOTICE:

Damage to your transaxle caused by shifting out of PARK (P) or NEUTRAL (N) with the engine racing isn’t covered by your warranty.

OVERDRIVE (a): This position is for normal driving. If you need more power for passing, and you’re:

Going less than 35 mph (55 kmk), push the accelerator pedal about halfway down. Going about 35 mph (55 kmh) or more, push the accelerator all the way down. The transaxle will shift down have more power.

to the next gear and

.NOTICE:

If your vehicle seems to start up rather slowly, or if it doesn’t seem to shift gears as you accelerate, something may be wrong with a transaxle system sensor.. If you drive very far that way, your vehicle can be damaged. So if this happens, have your vehicle serviced right away. Until then, you can use SECOND (2) when you are driving less than 35 mph (55 km/h) and,OVERDRIVE (a) for higher speeds.-

THIRD (3): This position is also. used for normal driving, however, it offers more power and lower fuel economy than OVERDRIVE (0). Here are examples for using THIRD (3) instead of OVERDRIVE (0):

When driving on hilly, winding roads. When towing a trailer, so there is less shifting between gears. . When going down a steep hill.

SECOND (2): This position gives you more power. You can use SECOND (2) on hills. It ,can help control your speed as you go down steep mountain roads, but then you wbuld also want to use your brakes off and on.

‘I NOTICE:

~~

Don’t shift into SECOND (2) unless you are going slower than 65 mph (105 km/h), or you can damage your engine.

2-25

FIRST (1): This position gives you even more power than SECOND (2). You can use it on very steep hills, or in deep snow or mud. (If the shft lever is put in FIRST (l), the transaxle won’t shift into gear until the vehicle is going slowly enough.)

I NOTICE:

~~

If your front wheels can’t rotate, don’t try to drive. This might happen if you were stuck in very deep sand or mud or were up against a solid object. You could damage your transaxle. Also, if you stop when going uphill, don’t hold your vehicle there with only the accelerator pedal. This could cause overheating and damage the transaxle. Use your brakes to hold your vehicle in position on a hill.

Parking Brake

Hold the regular brake pedal down with your right foot and push down the parking brake pedal with your left foot to set the parking brake. If the ignition is on, the PARK BRAKE indicator light should come on. If it doesn’t, you need to have your vehicle serviced.

If the parking brake has not been fully released and you try to drive off with the parking brake on, the PARK BRAKE indicator light comes on and stays on. See “Parking Brake Indicator Light” in the Index for more information. When you move out of PARK (P) or NEUTRAL (N), if the engine is running, the parking brake should release. If it doesn’t, you can manually release the parking brake.

2-26

Always shift to PARK (P) before pulling the manual release lever. If your hand or arm is in the way of the pedal you could be hurt. The pedal springs back quickly. Keep your hand and arm away when you use the manual release lever.

NOTICE:

Driving with the parking brake on can cause your rear brakes to overheat. You may have to replace them and you could also damage other parts of your vehicle.

If you are towing a trailer and are parking on a hill, see “Towing a Trailer” in the Index. This section shows what to do first to keep the trailer from moving.

---e 2-27

Before releasing the manual parking brake, be sure to put the vehicle in PARK (P) and turn the ignition to OFF. Reach under the driver’s side of the instrument panel and pull on the manual release lever, which is located above the parking brake pedal. If the parking brake does not release, you should either drive to the nearest service station or have your vehicle towed.

Steering Column Shift Lever (DeVie and DeVille d’Elegance Only) 1. Hold the brake pedal down with y o u right foot. 2. Move the shift lever into PARK (P) like this:

Shifting Into PARK (P)

It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, use the steps that follow. If you’re pulling a trailer, see “Towing a Trailer” in the Index.

Pull the lever toward you.

2-28

3.

4. 5.

0 Move the lever up as far as it will go. With your right foot still holding the brake pedal down, set the parking brake. Twn the ignition key to LOCK. Remove the key and take leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P).

it with you. If you can

Console Shift Lever 1. Hold the brake pedal down with your right foot. 2. Move the shift lever into PARK (P) like this:

0 Hold in the button on the lever and push the lever

all the way toward the front of your vehicle. 3. With your right foot still holding the brake pedal

down, set the parking brake.

4. Turn the ignition key to LOCK. 5. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P).

Torque Lock If you are parking on a hill and you don’t shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may find it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To find out how, see “Shifting Into PARK (P)” in the Index. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P).

Leaving Your Vehicle With the Engine Running

It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Don’t leave your vehicle with the engine running unless you have to.

If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is firmly set before you leave it. After you’ve moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without first pulling it toward you (or, if you have the console shift lever, without first pressing the button). If you can, it means that the shift lever wasn’t fully locked into PARK (P).

2-30

Shifting Out of PARK (P) Your vehicle has a Brake-Transaxle Shift Interlock (BTSI). You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN. See "Automatic Transaxle" in the Index. If you cannot shift out of PARK (P), ease pressure on the shift lever -- push the shift lever all the way into PARK (P) and also release the shift lever button on floor shift models as you maintain brake application. Then move the shift lever into the gear you want. (Press the the shift lever.) If you shift lever button before moving ever hold the brake pedal down but still can't shift out of PARK (P), try this: 1. Turn the key to OFF. Open and close the driver's door to turn off the Retained Accessory Power (RAP) feature.

2. Apply and hold the brake until the end of Step 4. 3. Shift to NEUTRAL (N). 4. Start the vehicle and then shift to the drive gear

you want.

5 . Have the vehicle fixed as soon as you can.

Parking Over Things That Burn

. .

Things that can burn could touch hot exhaust parts under your vehicle and ignite. Don't park over papers, leaves, dry grass or other things that can burn.

2-31

Engine Exhaust A CAUTION:

Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. You might have exhaust coming

in if:

Your exhaust system sounds strange or different. Your vehicle gets rusty underneath. Your vehicle was damaged in a collision. Your vehicle was damaged when driving over high points on the road or over road debris. Repairs weren’t done correctly. Your vehicle or exhaust system had been modified improperly.

If you ever suspect exhaust is coming into your vehicle:

Drive it only with all the windows down to blow out any CO; and Have your vehicle fixed immediately.

2-32

Running Your Engine While You’re Parked It’s better not to park with the engine running. But if you ever have to, here are some things to know.

A CAUTION:

Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle (see the earlier Caution under “Engine Exhaust”). Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if this can happen is a garage. Exhaust -- with the fan switch is at the highest setting. One place CO -- can come in easily. NEVER park in a

garage with the engine running. Another closed-in place can be a blizzard. (See “Blizzard” in the Index.)

It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake after you move the shift lever to PARK (P).

Follow the proper steps to be sure your vehicle won’t move. See “Shifting Into PARK (P)” in the Index. If you are parking on a hill and if you’re pulling a trailer, also see “Towing a Trailer” in the Index.

Windows Power Windows

The controls are located near each window. Press the control forward to raise the window and press rearward to lower. Note that the second rearward position on the driver’s control operates the express-down window feature. Your vehicle has Retained Accessory Power (RAP). When you stop your vehicle and turn the ignition key to OFF, you can still use your power windows. Electrical power to operate the windows will not shut off until you open a door or 10 minutes have passed. If you want this power for another 10 minutes, turn the key to RUN and back to OFF.

2-33

Express-Down Window This feature is present on the driver’s power window. Pressing the control rearward into the second position then releasing it will lower the window completely. If you want to stop the window as it is lowering, press the control forward. Press the control forward to raise the window. Note that the first position on the control operates the driver’s power window in the non-express mode.

Rear Window Lockout

. .

-:

Pressing the button down will disable the rear window controls. This is a useful feature if you have children as passengers. Press the button again to allow your passengers to reuse their window controls.

Horn The horn can be sounded by pressing on the center of the steering wheel pad. 2-34

Tilt Wheel

Tilt steering allows you to adjust the steering wheel before you drive. Raising the steering wheel to the highest level gives your legs more room when you enter and exit the vehicle. Hold the steering wheel and pull the lever toward you to tilt the wheel. Adjust the steering wheel to a comfortablc position and then release the lever to lock the wheel in place.

Turn SignaVMultifunction Lever Tbrn and Lane Change Signals To signal a turn, move the lever all the way up or down. The lever returns automatically when the turn is complete.

I An on the

arrow instrument

panel will flash in the direction of the turn or lane change.

Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is complete. The lever returns when it’s released. If the turn signal is left on, a warning chime will sound and the Driver Information Center (DIC) will display TURN SIGNAL ON (after driving about a mile) to remind you to turn it off.

Arrows that flash rapidly when signaling for a turn or lane change may be caused by a burned out signal bulb. Other drivers won’t see the turn signal. Replace burned-out bulbs to help avoid possible accidents. Check the fuse (see “Fuses and Circuit Breakers” in the Index) and for burned-out bulbs if the arrow fails to work when signaling a turn. Headlamp High/Low Beam Changer

Pull the turn signal lever all the way toward you and then release it to change the headlamps from low beam to high or from high beam to low.

This light on the instr..__lent panel will be on, indicating high beam usage.

Flash-To-Pass This lets you use the high-beam headlamps to signal the driver in front of you that you want to pass. Pull the turn signal lever toward you to use. When you do:

If the headlamps are either off or in the DRL mode, the high-beam headlamps will turn on. They'll stay on as long as you hold the lever there. Release the lever to turn them off. If the headlamps are on low beam, they will shift to high beam and stay there. Pull the lever toward you to return to low beam.

a If the headlamps are on high beam, they will switch to low beam. To return to high beam, pull the lever toward you.

Windshield Wipers

WIPER: Turn the band on the turn signal lever to control the wipers. MIST: Turn the band toward you and then release a single wiping cycle. For more cycles, hold the band - MIST longer. LO or HI: Turn the band away from you to either LO (low speed) or to HI (high speed), depending on the wiper speed you want.

it for on

DELAY: You can set the wiper speed for a long or short delay between wipes with this setting. Move the band to the DELAY position. The closer you move it to LO, the shorter the delay. (DeVille Only) OFF: Turn the band to OFF to turn off the wipers. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If the blades do become damaged, get new blades or blade inserts. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools. Clear away snow or ice to prevent an overload. Rainsense Wipers (DeVille d’Elegance and DeVille Concours Only) This moisture sensor is mounted on the passenger’s interior side of the windshield behind the rearview mirror and is used to automatically operate the wipers by monitoring the amount of moisture that is on the windshield.

The Rainsense system can be activated by turning the wiper stalk to one of the five sensitivity levels within the AUTO DELAY area. The AUTO DELAY position closest to OFF is the lowest sensitivity setting. This allows more water to collect on the windshield between wipes. Rotating the stalk away from you to the other AUTO DELAY settings increases the sensitivity of the system and frequency of wipes. A single wipe will occur each time you turn the wiper stalk to a higher sensitivity level. An initial wipe occurs when you turn the ignition on as a reminder that Rainsense is active. The windshield wipers also remain in a “high park” position (the wipers will stop on the windshield rather than their position), even when the ignition is turned off.

fully rested

2-37

The Rainsense wipers operate in a delay mode as well as a continuous low or high speed depending on the amount of moisture and the sensitivity level. The MIST and “wash” cycles operate as normal and are not affected by the Rainsense function.

Windshield Washer

NOTICE:

The wipers must be turned off when going through a car wash to avoid damage.

It is important to note that the Rainsense wiping feature (AUTO DELAY) can be overridden at any time by manually changing the wiper control to LO or HI speed. Note that if you ever need make sure it is Rainsense compatible.

to replace the windshield,

In freezing weather, don’t use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.

At the top of the turn signaVmultifunction lever, there is a paddle with the word PUSH on it. To spray washer fluid on the windshield, press and release this paddle. The wipers will clear the windshield and either stop or return to your preset speed. For more washer cycles, press and hold the paddle. LOW WASHER FLUID will be displayed on the Driver Information Center (DIC) when the washer fluid reaches a low level.

2-38

NOTICE:

Driving without washer fluid can be dangerous. A bad mud splash can block your vision could hit another vehicle or go off the road. Check the washer fluid level often.

and you

Cruise Control

With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can help on long trips. Cruise control does not work at speeds below 25 mph (40 M). Cruise control shuts off when you apply your brakes.

A CAIJTION:

Cruise control can be dangerous where you can’t drive safely at a steady speed. So, don’t use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Don’t use cruise control on slippery roads.

If your vehicle is in cruise control when the traction control system begins to limit wheel spin, the cruise control will automatically disengage. (See “Traction Control System” in the Index.) When road conditions allow you to safely use it again, you may turn the cruise control back on.

2-39

Setting Cruise Control

If you leave your cruise control switch on when you’re not using cruise, you might hit a button and go into cruise when you don’t want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use it.

1. Move the cruise control switch to ON. 2. Accelerate to the speed you want. 3. Press the SET CRUISE button at the end of the lever and release it. The CRUISE ENGAGED message will display on the Driver Information Center (DIC).

4. Remove your foot from the accelerator pedal. Resuming a Set Speed Setting the cruise control at a desired speed and then applying the brake will end the cruise function.

2-40

Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch from ON to R/A (Resume/Accelerate) for about half a second to reset. This returns you to your desired preset speed. Also note that the Driver Information Center (DIC) will display the CRUISE ENGAGED message again. Remember, if you hold the switch at R/A longer than half a second, the vehicle will accelerate until you release the switch or apply the brake. So unless you want to go faster, don’t hold the switch at R/A. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed. Push the button at the end of the lever and then release the button and the accelerator pedal. You’ll now cruise at the higher speed.

0 Move the cruise switch fiom ON to FUA. Hold it there until you reach a desired speed and then release the switch. (To increase your speed in very small amounts, move the switch to R/A. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster.)

The accelerate feature will only work after you have set the cruise control speed by pushing the SET CRUISE button.

Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control:

Push in the button at the end of the lever until you it. A reach a desired lower speed, then release CRUISE ENGAGED message will then display in the Driver Information Center (DIC). To slow down in very small amounts, push the button for less than half a second. Each time you do this, you’ll go 1 mph (1.6 km/h) slower.

Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier.

Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to. a lower gear to keep your speed down. Of course, applying the brakes or downshifting into FIRST (1) takes you out of cruise control. Many drivers find this to be too much trouble and don’t use cruise control on steep hills.

Ending Cruise Control There are two ways to end cruise control:

Step lightly on the brake pedal. Move the CRUISE switch to OFF.

Erasing Speed Memory The cruise control set speed memory is erased when you turn off the cruise control or the ignition.

2-41

Exterior Lamps

The control on the left side of the instrument panel controls these lamp systems:

0 Headlamps 0 Taillamps

Parking Lamps

0 Sidemarker Lamps 0 License Plate Lamp

Underhood Lamp Fog Lamps (DeVille Concours Only) Instrument Panel Lights 0 Interior Courtesy Lamps

2-42

first stop to turn on

Pull the lamp control knob out to the the parking and taillamps, sidemarker lamps and instrument panel lights. Pull the knob out all the way to turn on the headlamps. Push the control knob all the way back in to turn the lamps and lights off. Cluster lighting as well as instrument panel backlighting will dim only when it is dark outside. Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for approximately 20 seconds. In order to operate the wiper activated headlamps, the twilight sentinel must be turned on. This feature lights the way in poor weather and it also makes your vehicle more visible to other drivers. If the wiper activated headlamps are on, and the ignition switch is turned off, the wiper activated headlamps will immediately turn off. The wiper activated headlamps will deactivate if you turn off the twilight sentinel or if the windshield wipers have been turned off for a period of one or two seconds.

Lamps on Reminder You will hear a warning chime if you open any door while leaving the lamps on, if the manual headlamp control is activated. An exception to this is when you’re using twilight sentinel. Daytime Running Lamps Daytime Running Lamps (DRL) can make it easier for others to see the front o€ your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful short periods after dawn and before sunset. The DRL system will make the low-beam headlamps come on at reduced brightness when:

in the

the ignition is on, the headlamp switch is off and

0 the transaxle is not in PARK (P). When DRL are on, only your low-beam headlamps (at reduced brightness) will be on. No other exterior lamps such as the parking lamps, taillamps, etc. will be on when the DRL are being used. Your instrument panel won’t be lit up either.

When the twilight sentinel switch is on and it’s dark enough outside, the low-beam headlamps (at reduced intensity) will turn off and normal low-beam headlamp operation will occur. When the twilight sentinel switch is on and it’s bright enough outside, the regular lamps will go off, and the low-beam headlamps at reduced brightness will take over for the D m . If it’s dark enough outside and the twilight sentinel control is off, a HEADLAMPS SUGGESTED message will display on the Driver Information Center (DIC). This message informs the driver that turning on the exterior lamps is recommended even though are still illuminated (it’s become dark enough outside to require the headlamps and/or other exterior lamps). Turning on the twilight sentinel, the headlamp switch or the fog lamp switch will remove the HEADLAMPS SUGGESTED message. To idle your vehicle with the DRL off, turn off the twilight sentinel and shift the transaxle into PARK (P). Placing your vehicle in PARK (P) disables the D m . The DRL will stay off until you shift out of PARK (P). To drive your vehicle with the DRL off, turn off the twilight sentinel and manually turn on the parking lamps. As with any vehicle, you should turn on the regular headlamp system when you need it.

the DRL

2-43

Fog Lamps (DeVille Concours Only)

Use the fog lamps for better vision in foggy or misty conditions. When you press the fog lamp button, a small indicator light will tell you that the fog lamps and the parking lamps are on. Press the button again to turn them off.

If you switch on the high-beam headlamps, the fog lamps will turn off. They'll turn back on again when you switch to low-beam headlamps. When the twilight sentinel is on and the fog lamp switch is activated, the fog lamps will remain on as well as the headlamps and parking lamps.

Cornering Lamps The cornering lamps come on when the headlamps or parking lamps are on and you signal a turn. They provide more light for cornering. Twilight Sentinel

The control is next to the headlamp knob. It automatically switches the lamps on and off by sensing how dark it is outside.

TWILIGHT

To operate the twilight sentinel, leave the lamp knob off and move the TWILIGHT control to any position but OFF.

2-44

If you move the control all the way to the right, the lamps will remain on for approximately three minutes after the ignition has been turned to OFF or LOCK. If you move the control so it is just on, the lamps will go off quickly when you turn the ignition’switch out of RUN. You can adjust the delay time from only a few seconds to three minutes. If it’s dark enough outside and the twilight sentinel control is off, a HEADLAMPS SUGGESTED message will display on the Driver Information Center (DIC). This message informs the driver that tuming on the exterior lamps is recommended (it’s become dark enough outside to require the headlamps and/or other exterior lamps). Turning on the twilight sentinel, the headlamp switch or the fog lamp switch will remove the HEADLAMPS SUGGESTED message.

Light Sensor

. i

The light sensor for the DRL and the twilight sentinel is located in the center of the front defogger grille. If you cover the sensor, it will read “dark‘’ and the lamps will come on.

Courtesy Lamps (DeVille Only) The courtesy lamps are located in the roof in the rear seat. These lamps come ofi with the lamp knob or when any door is opened and it is dark outside. Illuminated Entry The illuminated eptry system turns on the courtesy lamps and the backlighting to, the 'door switches and to the lamp control knob when a door is opened or if you press a remote keyless entry transmitter button. Since the illuminated entry system has a photocell, this means that it must be dark outside in order for the courtesy lamps or backlighting to turn on. The courtesy lamps turn off approximately 20 seconds after the last door is closed or after the ignition key is placed in the ignition.

left on, the

Exterior Lighting Battery Saver If the manual parking lamp control has been exterior lamps will turn off approximately 10 minutes after the ignition is turned to LOCK or ACCESSORY. This protects draining the battery in case yoihave accidently left the headlamps or parking lamps on. If you need to purposely leave the lamps on for more than 10 minutes with the ignition in LOCK or ACCESSORY, turn the manual control knob off and then back on. To delay the lahps from turning off, see "Twilight Sentinel" earlier in this section. Interior Lamps Instrument Panel Brightness Control Cluster lighting as well as instrument panel lighting .automatically dims when it becomes dark outside and your lights are on. When it's dark, the brightness control can be manually adjusted by turning the lamp control knob to the left to dimand to the right to brighten the lighting. Cluster lighting and instrument panel lighting automatically brighten when it becomes light outside.

2-46

Parade Dimming This feature prohibits backlighting and the dimming of the instrument panel lights during daylight while the headlamps are on. This feature operates with the light sensor for the twilight sentinel and is fully automatic. When the light sensor reads darkness outside, the instrument panel lights can be adjusted. Backlighting to the instrument panel will also turn on. Reading Lamps (DeVille d’Elegance and DeVille Concours Only) The reading lamps are located in the roof. These lamps come on automatically when any door is opened and it is dark outside. For manual operation, press the button to turn them on. Press it again to turn them off. If the reading lamps are left on, they automatically shut off 10 minutes after the ignition has been turned off.

Map Lamps

These lamps are located in the front overhead panel. Press the button to turn them on. Press them off.

it again to turn

2-47

Mirrors Electrochromic Daymight Rearview Mirror When this feature is turned on, the mirror automatically changes to reduce glare from headlamps behind you. A photocell on the mirror senses when it is becoming dark outside. Another photocell, built into senses when headlamps are behind you. At night, when the glare is too high, the mirror will gradually darken to reduce glare (this change may take a few seconds). The mirror will return to state when.the glare is reduced.

its clear daytime

the mirror face,

Inadvertent Power Battery Saver This feature is designed to protect your vehicle’s battery against drainage from the interior lamps, trunk lamp, glove box lamp, cigarette lighters or the garage door opener. When the ignition is turned off, the power to these features will automatically turn off after 10 minutes (three minutes if a new car has 15 miles (24 km) or less). Power will be restored for an additional 10 minutes if any door is opened, the trunk is opened or the courtesy lamp switch is turned on. Storage Mode Personalization This feature is for long term use and must be programmed through the Driver Information Center (DIC) while the ignition is in RUN. Storage mode personalization protects the battery by placing your vehicle in a storage mode so that the radio, amplifiers, instrument cluster and remote keyless entry will not drain the battery over a long period of time. For programming information, see “Programmable, Memory and Personalization Features” later in this section.

2-48

Mirror Operation

Electrochromic Daymight Rearview Mirror with Compass (If Equipped)

To turn on the automatic dimming feature, press AUTO. To turn off automatic dimming, press OW. The green indicator light will be illuminated when this feature is active.

Time Delay The automatic mirror has a time delay feature which prevents unnecessary switching from the night back to the day position. This delay prevents rapid changing of the mirror as you drive under lights and through traffic.

Cleaning the Photocells Use a cotton swab and glass cleaner to clean the photocells when necessary.

Your vehicle may have an electrochromic inside rearview mirror with a compass. When set in the MIRROR position, this mirror automatically changes to reduce glare from headlamps behind you. The mirror also includes an eight-point compass display in the upper right corner of the mirror face. When on, the compass automatically calibrates as the vehicle is driven. When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.

Compass Operation Press the COMPASS switch once to turn the compass on or off. When the ignition and the compass feature are on, the compass will show two character boxes for approximately two seconds. After two seconds, the mirror will display the compass heading. If, after two seconds, the display does not show a compass heading ("N' for North, for example), there may be a strong magnetic field interfering with the compass. Such interference may be caused by a magnetic antenna mount, magnetic note pad holder or a similar magnetic item.

Mirror Operation

I-

The right side of the switch located at the bottom of the mirror turns the electrochromic mirror on and off. To turn on the automatic dimming feature, press MIRROR. To turn off automatic dimming, press MIRROR again. The green indicator light will be illuminated when this feature is active.

2-50

Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. Compass variance is the difference between earth’s magnetic north and true geographic north. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance: 1. Use the COMPASS button located at the bottom of

the mirror.

2. Press and hold the COMPASS button until a zone

number appears in the display.

3. Find your current location and variance zone number

on the following zone map.

4. Press the COMPASS button on the bottom of the mirror until the new zone number appears in the display. After you stop pressing the button, the display will show a “C” in the direction display within a few seconds. (This is the automatic calibration mode -- you’ll need to drive in a circle to calibrate the mirror. See “Compass Calibration” following.)

2-51

Compass Calibration If the letter “C” appears in the compass display, the mirror may need calibration. The mirror can be calibrated in one of two ways: 0 Drive the vehicle in circles at 5 mph (8 km/h) or less

until the display reads a direction, or

0 Drive the vehicle on’your everyday routine.

The control on the driver’s door armrest operates both outside rearview mirrors. Rotate the control knob to choose the right or left mirror.

To adjust the mirror, push the control knob in the direction you want the mirror to go. Adjust each mirror so you can see the side of your vehicle and the area behind your vehicle. When you operate the rear window defogger, it also warms both outside mirrors to help clear them of fog or ice. The mirrors can also be programmed for personalization if you have the optional memory package. For more information, see “Memory Seat and Mirrors” in the Index. Driver’s Outside Auto-Dimming Rearview Mirror Only the driver’s side outside mirror will adjust for the glare of headlamps behind you. This feature is controlled by the on and off settings on the electrochromic mirror. See “Electrochromic Daymight Rearview Mirror” earlier in this section.

2-52

Curb View Assist Mirror (If Equipped) If your vehicle is equipped with memory mirrors, it will . also be equipped with the curb view assist mirror feature. This featbre, will cause the passenger mirror to tilt when the vehicle is in REVERSE (R). This feature may be useful in allowing you to view the curb when you are parallel parking. When the vehicle is shifted out of REVERSE (R) and a, five second delay has occurred, the passenger.mirror , will return to its original position. If m e r adjustment is needed after the mirror is tilted, the mirror switch may be used.

,,

Convex Outside Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the, driver’s seat.

A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.

2-53

Storage Compartments Glove Box The glove box is located in front of the passenger’s seat. To lock the glove box door, insert the oval key into the lock cylinder and turn it to the right. Turn the key to the left to unlock the door. Map Pocket The maphtorage pockets are located on each front door as well as on the passenger’s and driver’s front seatbacks. Front Storage Armrest (DeVille and DeVille d’Elegance Only) The front storage area comes with a coinholder, a storage compartment for CDs or tapes, an optional phone and a dual cupholder that unfolds

for use.

2-54

Center Console Storage Area (DeVille Concours Only)

The full console includes a storage co,mpartment for CDs or tapes, an optional phone, an armrest and a cupholder. The cupholder can be opened by pressing on the surface panel located in front of the armrest. Close the lid to secure.

0

I nce Net

Rear Storage Armrest (If Equipped) Your vehicle may be equipped with a rear seat armrest which includes an open storage compartment and a dual cupholder that unfolds for use. To open, lift the front edge. (This feature is available on vehicles with leather interiors only.) Conver The convenience net is located inside the back wall of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over during sharp turns or quick starts and stops. The net is not for larger, heavier loads. Store them in the trunk as far forward as you can. When not using the net, hook the net to the tabs securing it to the sill plate. Ashtrays and Cigarette Lighter With the full center console (available on DeVille Concours only), press on the cover, which is located below the climate control system, to reveal the front ashtray. To clean this ashtray, lift it out by gripping the sides. For vehicles without the center console, pull the

is located beneath

tray out to reveal the ashtray. The tray the radio. To clean this ashtray, lift it out by pulling on the snuffer. To use the rear ashtray, lift the lid. I NOTICE: Don’t put papers or other flammable items into your ashtrays. Hot cigarettes or other smoking materials could ignite them, causing a damaging fire.

The cigarette lighter is located near the ashtray. Press it all the way in and release. It will pop back by itself when it’s ready to light. You may also have a lighter located at the rear seat air outlet. Note that power to the cigarette lighter will shut off 10 minutes after the ignition is turned off. This helps to prevent battery drainage. For more information, see “Inadvertent Battery Saver” earlier in this section.

2-55

NOTICE:

Don’t hold a cigarette lighter in with your hand while it is heating. If you do, it won’t be able to back away from the heating element when it’s ready. That can make it overheat, damaging the lighter and the heating element.

Illuminated Visor Vanity Mirror Turn the sunshade down and lift the cover to see the mirror. Move the slide switch up or down to brighten or dim the lamp. Illuminated Rear Seat Visor Vanity Mirror (If Equipped) Turn the sunshade down and lift the cover to see mirror. Move the slide switch up or down to brighten or dim the lamp. Cellular Telephone (Option)

the

ur 7isors awing down the visor to block out glare. It can also be detached from the center mount and moved to the side Your vehicle has been prewired for dealer installation of while the auxiliary sunshade remains to block glare from the front. h l l the front shade from the headliner and position it to your preference. The driver’s sunshade is also equipped with a storage flap that can be used for maps or toll tickets.

a Cadillac dual-mode (analog/digital) cellular telephone. A fixed mobile or a portable hand-heid system is available. Either system has steering wheel telephone controls and information output through the Driver Information Center (DIC). Voice activation and hands-free operation are standard features. For more information, contact your dealer. A user’s guide is provided with the telephone.

2-56

OnStar System (Option) This system may be ordered through your dealer and will include the optional fixed cellular telephone. The following services are available 24 hours a day:

Roadside Service with Location

0 Emergency Services Button

Remote Door Unlock Theft DetectiodNotification and S tolen-Vehicle Tracking Automatic Notification of Front Air Bag Deployment

0 Concierge/Customer Convenience Services For more information, contact your dealer.

out

Assist Handles A handle above each door can be used when getting of your vehicle.