2012 Cadillac CTS Owners Manual

positions with top tether anchors. H (Lower Anchor): Seating positions with two lower anchors.

Seats and Restraints

3-45

To assist in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. For a wagon the lower anchors are beneath zippers, near the labels. Open the zippers to access the lower anchors.

To assist in locating the top tether anchors, the top tether anchor symbol is on the cover.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (46,1)

3-46

Seats and Restraints

Be sure to use an anchor on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached. According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. See Where to Put the Restraint on page 3‑42 for additional information.

Sedan

Wagon

The top tether anchors for a sedan or a coupe are under the tether covers, on the rear seatback filler panel. For the wagon, the outboard top tether anchors are under the tether covers behind the rear seatback. The wagon's center top tether anchor is under the tether cover, on the vehicle floor, behind the rear seatback.

Coupe

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (47,1)

Seats and Restraints

3-47

{ WARNING

{ WARNING

Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.

Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them. Pull the shoulder belt all the way out of the retractor to set the lock, if the vehicle has one, after the child restraint has been installed.

Securing a Child Restraint Designed for the LATCH System

{ WARNING

If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (48,1)

3-48

Seats and Restraints

Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat. 1. Attach and tighten the lower

attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts.

Refer to your child restraint manufacturer instructions and the instructions in this manual. 1.1. Find the lower anchors for the desired seating position.

1.2. Put the child restraint on

the seat.

1.3. Attach and tighten the

lower attachments on the child restraint to the lower anchors.

2.

If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2. Press the ribbed area of the cover to open the cover and expose the anchor.

2.3. If you have an adjustable

head restraint, raise the head restraint.

2.4. Route, attach, and tighten

the top tether according to your child restraint instructions and the following instructions:

If the position you are using does not have a headrest or head restraint and you are using a single tether, route the tether over the seatback.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (49,1)

If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback.

If the position you are using has a fixed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.

Seats and Restraints

3-49

If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the headrest or head restraint.

3. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the LATCH path and attempt to move it side‐to‐side and back‐and‐forth. There should be no more than 2.5 cm (1 in) of movement for proper installation.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (50,1)

3-50

Seats and Restraints

Replacing LATCH System Parts After a Crash { WARNING

A crash can damage the LATCH system in the vehicle. A damaged LATCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash. To help make sure the LATCH system is working properly after a crash, see your dealer to have the system inspected and any necessary replacements made as soon as possible.

If the vehicle has the LATCH system and it was being used during a crash, new LATCH system parts may be needed. New parts and repairs may be necessary even if the LATCH system was not being used at the time of the crash.

Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑43 for how and where to install your child restraint using LATCH. If a child restraint is secured in the vehicle using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑43 for top tether anchor locations. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.

In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. If the child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say. If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 3‑42. 1. Put the child restraint on

the seat.

2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (51,1)

Seats and Restraints

3-51

3. Push the latch plate into the

4. Pull the shoulder belt all the way

buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.

out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.

5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 4 and 5.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (52,1)

3-52

Seats and Restraints

6.

If the child restraint has a top tether, follow the child restraint manufacturer's instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH System) on page 3‑43 for more information.

7. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position. If the top tether is attached to a top tether anchor, disconnect it.

Securing Child Restraints (Front Passenger Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 3‑42
In addition, the vehicle has a passenger sensing system which is designed to turn off the front passenger frontal airbag under certain conditions. See Passenger Sensing System on page 3‑28 and Passenger Airbag Status Indicator on page 5‑19 for more information, including important safety information. A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys.

{ WARNING

A child in a rear-facing child restraint can be seriously injured or killed if the front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the front passenger airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the front passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off.

(Continued)

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (53,1)

WARNING (Continued)

Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat. See Passenger Sensing System on page 3‑28 for additional information.

If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑43 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH System) on page 3‑43 for top tether anchor locations.

Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached. You will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it

will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the front passenger frontal airbag, the off indicator on the passenger airbag status indicator should light and stay lit when the vehicle is started. See Passenger Airbag Status Indicator on page 5‑19.

Seats and Restraints

3-53

2. Put the child restraint on

the seat.

3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint. The child restraint instructions will show you how.

4. Push the latch plate into the

buckle until it clicks. Position the release button on the buckle, so that the safety belt could be quickly unbuckled if necessary.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (54,1)

3-54

Seats and Restraints

7. Before placing a child in the

child restraint, make sure it is securely held in place. To check, grasp the child restraint at the safety belt path and attempt to move it side to side and back and forth. When the child restraint is properly installed, there should be no more than 2.5 cm (1 in) of movement.

If the airbag is off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the on indicator is lit, see “If the On Indicator Is Lit for a Child Restraint” under Passenger Sensing System on page 3‑28 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.

5. Pull the shoulder belt all the way

out of the retractor to set the lock. When the retractor lock is set, the belt can be tightened but not pulled out of the retractor.

6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt. Try to pull the belt out of the retractor to make sure the retractor is locked. If the retractor is not locked, repeat Steps 5 and 6.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (1,1)

Storage

4-1

Storage Compartments

Instrument Panel Storage

Cupholders

Storage

Storage Compartments

Instrument Panel Storage . . . . . 4-1
Glove Box . . . . . . . . . . . . . . . . . . . . 4-1
Cupholders . . . . . . . . . . . . . . . . . . . 4-1
Center Console Storage . . . . . . 4-2

Additional Storage Features

Cargo Cover (Wagon) . . . . . . . . . 4-2
Cargo Management System

(Wagon Only) . . . . . . . . . . . . . . . . 4-3
Cargo Net (Wagon) . . . . . . . . . . . 4-4
Convenience Net

(Sedan and Coupe) . . . . . . . . . . 4-5

Roof Rack System

Roof Rack System (Wagon) . . . 4-6

There are cupholders in the front of the center console. Push the cover to open. There are also cupholders in the rear center armrest. Pull the armrest down to use.

There is a storage area below the climate control system. To access, push the cover.

Glove Box To open, press the button. Use the key to lock and unlock. The glove box has a shelf that can be removed by pulling it out.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (2,1)

4-2

Storage

Center Console Storage

Additional Storage Features

Cargo Cover (Wagon) The cargo cover can be used to cover items in the cargo area.

The center console has an upper and lower storage area. To access, lift the levers on either side of the center console. There is an additional storage area behind the center console. To access, push the cover.

To install the cargo cover: 1. Hold the cartridge with the

pull-out shade toward the rear of the vehicle.

2. Align the cartridge over the

pin (B) on both sides. Press the cartridge down and turn it slightly forward until it clicks.

3. The cartridge is properly

installed if it fits firmly when pulled and pushed.

4. Grasp the handle and unroll the

cover. Latch the posts into the sockets.

To remove the cargo cover: 1. Release the cover from the latch

posts and carefully roll it back up.

2. Pull the handle (A) back and

remove it from the pin (B) on the trim panel. Repeat this on the other side.

{ WARNING

An unsecured cargo cover could strike people in a sudden stop or turn, or in a crash. Store the cargo cover securely or remove it from the vehicle.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (3,1)

Cargo Management System (Wagon Only)

The cover can be opened to two positions to allow access to the storage area. Some items may be stored in the cargo area when the cover is closed.

Press the bottom of the load floor handle assembly to lift the top on the handle. Pull up on the handle to open the cargo management system.

Storage

4-3

D-Ring Sliders There are four D-Ring sliders that move along rails on both sides of the cargo management area. These can be used as tie-downs when storing cargo.

Installing D-Ring Sliders

To install the D-Ring slider (A), insert it into the channel (B) located in the middle of each rail.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (4,1)

4-4

Storage

Cargo Net (Wagon) { WARNING

Do not stack items higher than the upper end of the cargo net or hang anything from the net. Avoid items that have sharp edges or that apply excessive force to the net. If items are not properly stored, damage to the net could occur and items can be thrown about the vehicle. You or others could be injured. Always store items behind the net.

For vehicles equipped with a cargo net, it can be used to store light loads, keeping them from falling over or being thrown. The net should not be overloaded or used to store heavy loads.

1. There are four installation points in the roof, two located in front of and two behind the rear seats. Insert the top corners of the cargo net into the large opening in the roof and secure by sliding them into the small opening.

2. There are four tether positions

for the lower hook straps. In the front position, the seatbacks should be down for the net to properly hold items.

The loop of the D-Ring slider must be facing inward toward the storage area and the ring must be in the up position for proper usage. Push the button to move the D-Ring slider. The rings can be locked into various positions along the rail.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (5,1)

Storage

4-5

3. Mount the cargo net to the rear seat tethers located on the front of the bottom cushions.

4. The net can also be mounted to

5. Pull on the straps to tighten

the tethers on the back of the rear seats when the seats are upright.

the net.

Convenience Net (Sedan and Coupe) The vehicle may have a convenience net in the rear. Put small loads behind the net. It can also be positioned into an envelope style to hold smaller items. The net is not for heavier loads. Store items as far forward as you can.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (6,1)

4-6

Storage

Roof Rack System

Roof Rack System (Wagon)

{ WARNING

If something is carried on top of the vehicle that is longer or wider than the roof rack — like paneling, plywood, or a mattress — the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision and damage the vehicle. Never carry something longer or wider than the roof rack on top of the vehicle unless using a GM certified accessory carrier.

For vehicles with a roof rack, the rack can be used to load items. For roof racks that do not have crossrails included, GM Certified crossrails can be purchased as an accessory. See your dealer for additional information. Notice: Loading cargo on the roof rack that weighs more than 75 kg (165 lbs) or hangs over the rear or sides of the vehicle may damage the vehicle. Load cargo so that it rests evenly between the crossrails, making sure to fasten cargo securely.

To prevent damage or loss of cargo when driving, check to make sure crossrails and cargo are securely fastened. Loading cargo on the roof rack will make the vehicle’s center of gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control. If driving for a long distance, on rough roads, or at high speeds, occasionally stop the vehicle to make sure the cargo remains in its place. Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Vehicle Load Limits on page 9‑12.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (7,1)

Installing the Crossrails

Storage

4-7

A. Crossrails B. Siderail Cover Before installing the crossrails (A), remove the siderail covers (B). Pull straight up on the rear of the siderail cover. Store covers flat, do not stack items on them.

1.

Identify the front and rear crossrail.

2. The front crossrail (A) is smaller

than the rear crossrail (B).

3. The crossrail supports are

labeled with an arrow (B) that needs to point toward the front of the vehicle. A pin (A) will be visible on the bottom when the crossrail support lever is down. To install the crossrail support, move the lever into the forward upper position; the pin (A) will not be visible.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (8,1)

4-8

Storage

5.

4. Locate the forward or rearward cut-out in the siderail channel. Insert both crossrail ends into the cut-outs, making sure the arrows are pointed toward the front of the vehicle.

Removing the Crossrails 1. Move both levers of the crossrail

into the upper forward position.

2. Slide the crossrail into the

cut-out area.

3. Remove the crossrail from the

vehicle.

4. Repeat for the other crossrail. 5. Replace the siderail covers on

the siderails.

6. Levers must still be in the

forward up position. Move the front crossrail forward beyond the cut-out area (B). For the rear crossrail, slide the crossrail assembly (A) rearward until the entire crossrail support is in first position beyond the channel cut-out area (B).

7. Move the levers on both

crossrails to the down position. Slide the crossrail until the crossrail pin engages.

8. The crossrails should lock in the same hole position on each side.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (1,1)

Instruments and Controls

5-1

Instruments and Controls

Controls

Steering Wheel Adjustment . . . 5-2
Steering Wheel Controls . . . . . . 5-3
Heated Steering Wheel . . . . . . . 5-4
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Windshield Wiper/Washer . . . . . 5-4
Rear Window

Wiper/Washer . . . . . . . . . . . . . . . 5-6
Headlamp Washer . . . . . . . . . . . . 5-7
Compass . . . . . . . . . . . . . . . . . . . . . 5-8
Clock . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Power Outlets . . . . . . . . . . . . . . . 5-10
Cigarette Lighter . . . . . . . . . . . . . 5-10
Ashtrays . . . . . . . . . . . . . . . . . . . . . 5-11

Warning Lights, Gauges, and Indicators

Warning Lights, Gauges, and

Indicators . . . . . . . . . . . . . . . . . . . 5-11
Instrument Cluster . . . . . . . . . . . 5-12
Speedometer . . . . . . . . . . . . . . . . 5-14

Odometer . . . . . . . . . . . . . . . . . . . . 5-14
Trip Odometer . . . . . . . . . . . . . . . 5-14
Tachometer . . . . . . . . . . . . . . . . . . 5-14
Fuel Gauge . . . . . . . . . . . . . . . . . . 5-14
Boost Gauge . . . . . . . . . . . . . . . . 5-15
Engine Speed Limiter . . . . . . . . 5-16
Engine Oil Pressure

Gauge . . . . . . . . . . . . . . . . . . . . . . 5-16

Engine Coolant Temperature

Gauge . . . . . . . . . . . . . . . . . . . . . . 5-17
Safety Belt Reminders . . . . . . . 5-18
Airbag Readiness Light . . . . . . 5-18
Passenger Airbag Status

Indicator . . . . . . . . . . . . . . . . . . . . 5-19
Charging System Light . . . . . . 5-20
Malfunction

Indicator Lamp . . . . . . . . . . . . . 5-20

Brake System Warning

Light . . . . . . . . . . . . . . . . . . . . . . . 5-23

Antilock Brake System (ABS)

Warning Light . . . . . . . . . . . . . . 5-24
Up-Shift Light . . . . . . . . . . . . . . . . 5-25
StabiliTrak® OFF Light . . . . . . . 5-25
Traction Control System

(TCS)/StabiliTrak® Light . . . . 5-25

Engine Coolant Temperature

Warning Light . . . . . . . . . . . . . . 5-26
Tire Pressure Light . . . . . . . . . . 5-26
Engine Oil Pressure Light . . . . 5-27
Security Light . . . . . . . . . . . . . . . . 5-27
High-Beam On Light . . . . . . . . . 5-27
Front Fog Lamp Light . . . . . . . . 5-28
Lamps On Reminder . . . . . . . . . 5-28
Cruise Control Light . . . . . . . . . 5-28

Information Displays

Driver Information

Center (DIC) . . . . . . . . . . . . . . . 5-28

Vehicle Messages

Vehicle Messages . . . . . . . . . . . 5-33
Battery Voltage and

Charging Messages . . . . . . . . 5-33
Brake System Messages . . . . 5-34
Compass Messages . . . . . . . . . 5-35
Cruise Control Messages . . . . 5-35
Door Ajar Messages . . . . . . . . . 5-36
Engine Cooling System

Messages . . . . . . . . . . . . . . . . . . 5-36
Engine Oil Messages . . . . . . . . 5-37
Engine Power Messages . . . . 5-38

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (2,1)

5-2

Instruments and Controls

Fuel System Messages . . . . . . 5-38
Key and Lock Messages . . . . . 5-38
Lamp Messages . . . . . . . . . . . . . 5-41
Object Detection System

Messages . . . . . . . . . . . . . . . . . . 5-41

Ride Control System

Messages . . . . . . . . . . . . . . . . . . 5-42
Airbag System Messages . . . . 5-44
Anti-theft Alarm System

Messages . . . . . . . . . . . . . . . . . . 5-45
Service Vehicle Messages . . . 5-45
Tire Messages . . . . . . . . . . . . . . . 5-45
Transmission Messages . . . . . 5-46
Vehicle Speed Messages . . . . 5-47
Washer Fluid Messages . . . . . 5-47

Vehicle Personalization

Vehicle Personalization . . . . . . 5-48

Universal Remote System

Universal Remote System . . . 5-56
Universal Remote System

Programming . . . . . . . . . . . . . . . 5-56

Universal Remote System

Operation . . . . . . . . . . . . . . . . . . 5-59

Controls

Steering Wheel Adjustment

Power Tilt Wheel

For vehicles with the power tilt wheel, the control is on the left side of the steering column. . Push the control up or down to

tilt the steering wheel up or down.

. Push the control forward or

rearward to move the steering wheel toward the front or rear of the vehicle.

Do not adjust the steering wheel while driving.

To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up

or down.

3. Pull or push the steering wheel

closer or away from you.

4. Pull the lever up to lock the

steering wheel in place.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (3,1)

Steering Wheel Controls

Some audio steering wheel controls could differ depending on the vehicle's options. Controls that can be adjusted at the steering wheel may include: SRCE (Source): Press to switch between AM, FM, or XM™ (if equipped) radio, CD, DVD (if equipped), HDD (if equipped), auxiliary input jack, and USB (if equipped).

Instruments and Controls

5-3

For vehicles without a navigation system, press and hold b / g for two seconds to interact with OnStar® or Bluetooth. See OnStar Overview on page 14‑1 or Bluetooth on page 7‑38 for more information about these features. For vehicles with a navigation system, OnStar, or Bluetooth, press and hold b / g for two seconds and say “hands free” to interact with OnStar or Bluetooth. See the OnStar Owner's Guide, or Bluetooth on page 7‑38 for more information about these features.

y or c / z (Previous/Next): Press to go to the previous or next radio station stored as a favorite, or the previous or next track of a CD. Press to interact with the Bluetooth® system. See Bluetooth on page 7‑38 for more information.

+ e − (Volume): Press to increase or to decrease the volume. b / g (Mute/Speech Recognition/ Push to Talk): Press and release to silence the vehicle speakers only. The audio of the wireless and wired headphones, if the vehicle has these features, do not mute. Press and release b / g again, to turn the sound on.

For vehicles with a navigation system, press and hold b / g for two seconds to initiate speech recognition. See “Speech Recognition” in the navigation manual for more information.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (4,1)

5-4

Instruments and Controls

Heated Steering Wheel The vehicle may be equipped with a heated steering wheel.

Horn Press a on the steering wheel pad to sound the horn.

Windshield Wiper/Washer

Sedan and Coupe Model Shown

( (Heated Steering Wheel): Press to turn the heated steering wheel on or off. A light on the button displays when the feature is turned on. The steering wheel takes about three minutes to start heating.

Wagon Model Shown

The windshield wiper lever is on the right side of the steering column. Move the windshield wiper lever to select the wiper speed.

8 (Mist): Single wipe, briefly move the lever down and release. Several wipes, hold the lever down. ( (Off): Turns the wipers off. 3 (Adjustable Interval Wipes): For a delayed wiping cycle. Turn the band up for more frequent wipes or down for less frequent wipes. 1: Slow wipes. 2: Fast wipes. If the windshield wipers are in use for about six seconds while you are driving, the exterior lamps come on automatically if the exterior lamp control is in AUTO. See “Wiper Activated Headlamps” for more information. Clear snow and ice from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. For more information, see Wiper Blade Replacement on page 10‑34.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (5,1)

Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Rainsense™ For vehicles with Rainsense, a sensor located near the top center of the windshield detects the amount of water on the windshield and automatically controls the frequency of the windshield wiper. Keep this area of the windshield clear of debris to allow for best system performance.

Sedan and Coupe Model Shown,

Wagon Model Similar

Instruments and Controls

5-5

3 (Rainsense Wipe Sensitivity Control): Move the windshield wiper lever to 3. Turn the 3
band on the wiper lever to adjust the sensitivity.

Turn the band up for more sensitivity to moisture. Turn the band down for less sensitivity to moisture.

. Move the windshield wiper lever

out of the 3 position to deactivate Rainsense.

Wiper Arm Assembly Protection When using an automatic car wash, move the windshield wiper lever to the ( position. This disables the windshield wipers and/or rear wipers, if equipped.

Windshield Washer

{ WARNING

In freezing weather, do not use the washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.

Sedan and Coupe Model K (Washer Fluid): Press the button with this symbol, on the end of the windshield washer lever to wash the windshield. The washer fluid sprays onto the windshield and the wipers run for a few cycles to clear the windshield. Press and hold K for more wash cycles.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (6,1)

5-6

Instruments and Controls

Wagon Model Pull the lever toward you to spray washer fluid on the windshield. The spray continues until the lever is released. The wipers will run a few times. WASHER FLUID LOW ADD FLUID displays on the Driver Information Center (DIC) when the washer fluid is low. See Washer Fluid Messages on page 5‑47. See Washer Fluid on page 10‑26 for information on filling the windshield washer fluid reservoir. If the headlamps are on while the windshield is being washed, the headlamp washers, if the vehicle has them, will also turn on. See “Headlamp Washer” following for more information.

Rear Window Wiper/Washer For vehicles with a rear window wiper/washer, the controls are on the end of the windshield wiper lever.

Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for about six seconds. For this feature to work, the exterior lamp control must be in AUTO. The wiper-activated headlamps immediately turn off, when the ignition is turned to LOCK/OFF or the windshield wiper control is turned off.

Press the upper or lower portion of the button to control the rear wiper and rear wiper delay. The system turns off when the button is returned to the middle position.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (7,1)

Instruments and Controls

5-7

Z (Rear Wiper Delay Short): Sets a five‐second delay between wipes. 5 (Rear Wiper Delay Long): Sets a 10‐second delay between wipes. = (Rear Washer): Push the windshield wiper lever forward to spray washer fluid on the rear window. The lever returns to its starting position when released. The windshield washer reservoir is used for the windshield and the rear window. Check the fluid level in the reservoir if either washer is not working. See Washer Fluid on page 10‑26.

Headlamp Washer For vehicles with headlamp washers they clear debris from the headlamp lenses.

The headlamp washers are beneath the headlamps.

Press the washer button at the end of the windshield wiper lever to wash the headlamps. Both the headlamps and the windshield will be washed. After the first wash, the headlamps will not be washed until the fifth press of the windshield washer button. The headlamps must be on to be washed. If the headlamps are off, only the windshield will be washed when the washer button is pressed. If the washer fluid is low, the headlamp washers will not work. See Windshield Wiper/Washer on page 5‑4 for more information.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (8,1)

5-8

Instruments and Controls

Compass The vehicle may have a compass in the Driver Information Center (DIC).

Compass Zone The zone is set to zone eight. If you do not live in zone eight or drive out of the area, the variance needs to be changed to the appropriate zone. To adjust for compass variance, use the following procedure:

Compass Variance (Zone) Procedure 1. Do not set the compass zone

when the vehicle is moving. On an automatic transmission vehicle, only set it when the vehicle is in P (Park). On a manual transmission vehicle, only set it when the vehicle is stopped.

Press T until PRESS V TO CHANGE COMPASS ZONE displays.

2. Find the vehicle's current

location and variance zone number on the map. Zones 1 through 15 are available.

3. Press V to scroll through and select the appropriate variance zone.

4. Press 3 until the

vehicle heading, for example, N for North, is displayed in the DIC.

5. Calibrate the compass.

See “Compass Calibration Procedure” following.

Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. Also calibrate the compass, away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible. If the DIC display does not show a heading, for example, N for North, or the heading does not change after making turns, there may be a strong magnetic field interfering with

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (9,1)

Instruments and Controls

5-9

the compass. Interference may be caused by a magnetic antenna mount, magnetic note pad holder, or any other magnetic item. Turn off the vehicle, move the magnetic item, then turn on the vehicle and calibrate the compass.

Compass Calibration Procedure 1. Before calibrating the compass,

check that the compass is set to the correct variance zone. See “Compass Variance (Zone) Procedure” earlier in this section. Do not operate any switches such as window, sunroof, climate controls, seats, etc. during the calibration procedure.

2. Press T until PRESS V TO

CALIBRATE COMPASS displays.

3. Press V to start the compass

calibration.

4. The DIC will display

CALIBRATING DRIVE IN CIRCLES. Drive the vehicle in tight circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE for a few seconds then returns to the PRESS V TO CALIBRATE COMPASS display.

Clock The analog clock is on the instrument panel above the radio. The clock is not connected with any other vehicle system and runs by itself. To adjust the clock: 1. Locate the adjustment buttons

directly below the clock.

2. Push and release the right

adjustment button to move the clock hands forward or the left adjustment button to make the clock hands go backward. Holding either button down will cause the clock to advance faster. Release the button before the desired time is reached.

3. Push and release either button

to adjust the time by one minute increments.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (10,1)

5-10

Instruments and Controls

Power Outlets Accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player. There are three accessory power outlets. The power outlets located below the climate control system, inside the center console storage bin, and on the rear of the center console are powered while the vehicle is in ON/RUN, START or ACC/ACCESSORY mode, or until the driver door is opened within 10 minutes of turning off the vehicle. On the CTS Wagon there is an additional accessory power outlet located near the rear cargo net that is powered at all times. Remove the cover to access and replace when not in use. Notice: Leaving electrical equipment plugged in for an extended period of time while the vehicle is off will drain the

battery. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 ampere rating. Certain electrical accessories may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. See Add-On Electrical Equipment on page 9‑63. Notice: Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords.

Cigarette Lighter The vehicle may have a cigarette lighter. To use the lighter, push it in all the way and let go. When it is ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating does not let the lighter back away from the heating element when it is hot. Damage from overheating can occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (11,1)

Instruments and Controls

5-11

Ashtrays The vehicle may have two removable ashtrays. One ashtray can be placed into the instrument panel storage compartment and the other into the center console rear compartment. To empty the ashtrays, hold on to the edges of the bin and pull straight out. To reinstall, push the tray back into place. Notice: If papers, pins, or other flammable items are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put flammable items in the ashtray.

Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury. Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working.

Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle. When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Follow this manual's advice. Waiting to do repairs can be costly and even dangerous.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (12,1)

5-12

Instruments and Controls

Instrument Cluster

English Shown, Metric Similar

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (13,1)

Instruments and Controls

5-13

English V-Series Shown, Metric and Manual Similar

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (14,1)

5-14

Instruments and Controls

Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).

Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper‐resistant odometer. The digital odometer will read 999,999 if it is turned back. If the vehicle needs a new odometer installed, it must be set to the mileage total of the old odometer. If that is not possible, then it must be set at zero and a label must be put on the driver door to show the old mileage reading when the new odometer was installed.

Trip Odometer The trip odometer can record the number of kilometers or miles traveled for up to two trips. The trip odometer is part of the Driver Information Center (DIC); for more information see Driver Information Center (DIC) on page 5‑28. For vehicles that have the navigation system, see the navigation manual for more information.

Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: If the engine is operated with the tachometer in the shaded warning area, the vehicle could be damaged, and the damages would not be covered by the vehicle warranty. Do not operate the engine with the tachometer in the shaded warning area.

The CTS-V tachometer has tracer lights that follow the movement of the tachometer indicator. The tracer lights also flash when it is time to up-shift to avoid the engine speed limit. See Automatic Transmission on page 9‑28 or Manual Transmission on page 9‑32 for more information.

Fuel Gauge

When the ignition is on, the fuel gauge indicates how much fuel is left in the tank.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (15,1)

An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. The FUEL LEVEL LOW message appears in the Driver Information Center (DIC) and a single chime sounds. See Fuel System Messages on page 5‑38 for more information. Normal operation of the fuel gauge includes: . At the service station, the fuel

pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. The gauge moves a little while turning a corner or speeding up. The gauge takes a few seconds to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.

Instruments and Controls

5-15

Boost Gauge

Metric

English

For the CTS-V, this gauge is located in the instrument panel cluster. This gauge indicates positive manifold pressure, which is the induction air pressure level in the intake manifold before it enters the combustion chamber. This gauge reads zero under light throttle before boost is generated. The gauge automatically resets to zero every time the engine is started.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (16,1)

5-16

Instruments and Controls

Engine Speed Limiter This feature prevents the engine speed from reaching an unsafe level. If the level is too high, the throttle closes or limits the fuel supply until the engine speed returns to a safe level. Throttle operation and fuel supply return to normal when engine speed is lowered. For the CTS-V, the tachometer tracer lights flash prior to reaching engine speed limit. The tracer lights also flash on automatic transmission vehicles while in the DSC or Tap Shift modes.

Engine Oil Pressure Gauge

Metric

English

For vehicles with an engine oil pressure gauge, it shows the engine oil pressure in kPa (kilopascals) or psi (pounds per square inch) when the engine is running. Oil pressure may vary with engine speed, outside temperature, and oil viscosity, but if readings are outside the normal operating range, the oil pressure light will come on. See Engine Oil Pressure Light on page 5‑27 for more information.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (17,1)

Instruments and Controls

5-17

A reading outside the normal operating range may be caused by a dangerously low oil level or some other problem causing low oil pressure. Oil should be checked as soon as possible. See Oil Pressure Low Stop Engine under Engine Oil Messages on page 5‑37 and Engine Oil on page 10‑10.

{ WARNING

Do not keep driving if the oil pressure is low. The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.

Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty.

low can also damage the

Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.

Engine Coolant Temperature Gauge

English

This gauge shows the engine coolant temperature. If the engine coolant overheats, the engine coolant temperature warning light comes on. See Engine Coolant Temperature Warning Light on page 5‑26 and Engine Overheating on page 10‑24 for more information.

Metric

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (18,1)

5-18

Instruments and Controls

Safety Belt Reminders

Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster.

Passenger Safety Belt Reminder Light

When the vehicle is started, this light flashes and a chime may come on to remind front passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. See Passenger Airbag Status Indicator on page 5‑19. This cycle continues several times if the front passenger remains or becomes unbuckled while the vehicle is moving. If the front passenger safety belt is buckled, neither the chime nor the light comes on.

When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.

The front passenger safety belt reminder light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the reminder light and/or chime, remove the object from the seat or buckle the safety belt.

Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑21.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (19,1)

Instruments and Controls

5-19

Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑28 for important safety information. The instrument panel has a passenger airbag status indicator.

United States

Canada and Mexico

When the vehicle is started, the passenger airbag status indicator will light the words ON and OFF, or the symbols for on and off, for several seconds as a system check. If the vehicle has remote start, and it is being used to start the vehicle from a distance, you may not see the system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol, to let you know the status of the right front passenger frontal airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the outboard front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the passenger airbag status indicator, it means that the passenger sensing system has turned off the outboard front passenger frontal airbag.

The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have the vehicle fixed immediately.

{ WARNING

If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (20,1)

5-20

Instruments and Controls

If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. { WARNING

If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑18 for more information, including important safety information.

Charging System Light

The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, the Driver Information Center (DIC) also displays a message.

See Battery Voltage and Charging Messages on page 5‑33. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.

Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, to produce a cleaner environment. This light comes on when the vehicle is placed in ON/RUN, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions (Key Access) on page 9‑17 or Ignition Positions (Keyless Access) on page 9‑19 for more information.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (21,1)

Instruments and Controls

5-21

Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to

pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.

If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.

This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. If the malfunction indicator lamp comes on and stays on while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the dealer technician in correctly diagnosing any malfunction.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (22,1)

5-22

Instruments and Controls

If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emissions system malfunction: . Check that the fuel cap is fully

installed. See Filling the Tank on page 9‑55. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.

. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It will require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑52. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed.

Emissions Inspection and Maintenance Programs Some local governments may have programs to inspect the on-vehicle emission control equipment. For the inspection, the emission system test equipment is connected to the vehicle’s Data Link Connector (DLC).

The DLC is under the instrument panel to the next to the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:

The malfunction indicator lamp is on with the engine running, or if the light does not come on when the ignition is turned to ON/RUN while the engine is off.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (23,1)

Instruments and Controls

5-23

See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.

Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there is a brake problem. Have the brake system inspected right away.

Metric

English

This light should come on briefly when the ignition is placed in ON/RUN. If it does not come on then, have it fixed so it will be ready to warn if there is a problem.

When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light flashes or stays on if the parking brake is not fully released. If the light stays on after the parking brake is fully released, there is a base brake problem.

{ CAUTION

The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.

Cadillac CTS/CTS-V Owner Manual (Include Mex) - 2012

Black plate (24,1)

5-24

Instruments and Controls

For vehicles with the Electric Parking Brake (EPB), this red brake status light comes on when the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the Electric Parking Brake system. If the light does not come on, or remains flashing, see your