Download PDF Manual

This message appears when the electronic sensors that control the air conditioning and heating systems are no longer working. Have the climate control system serviced by your dealer if you notice a drop in heating and air conditioning efficiency. Service Air Bag There is a problem with the airbag system when this message appears. Have your vehicle serviced by your dealer immediately. See Airbag Readiness Light on page 192 for more information. Service Brake Assist This message will display when a problem with the panic brake assist system has been detected. Have your vehicle serviced by your dealer.


Service Charging System This message will display when a problem with the charging system has been detected. Have your vehicle serviced by your dealer. Service Electrical System This message will display if an electrical problem has occurred within the Powertrain Control Module (PCM) or the ignition switch. Have your vehicle serviced by your dealer. Service Fuel System The Powertrain Control Module (PCM) has detected a problem within the fuel system when this message appears. Have your vehicle serviced by your dealer. Service Idle Control A problem with the idle control has occurred when this message displays. Have your vehicle serviced by your dealer.


235


Service Stability System If your vehicle has StabiliTrak®, this message will be displayed if there has been a problem detected with StabiliTrak®. If this message comes on while you are driving, pull off the road as soon as possible and stop carefully. Try resetting the system by turning the ignition off and then back on. If this message still stays on, or comes back on again while you are driving, your vehicle needs service. Have the StabiliTrak® system inspected by your dealer as soon as possible. See StabiliTrak® System on page 299 for more information. Service Steering System Your vehicle may have a speed variable assist steering system. See Steering on page 300. This message will be displayed if a problem is detected with the speed variable assist steering system. When this message is displayed, you may notice that the effort required to steer the vehicle increases or feels heavier, but you will still be able to steer the vehicle.


Service Theft System This message means there is a problem with the immobilizer. See Immobilizer on page 109 for more information. A fault has been detected in the system, which means that the system is disabled and is not protecting the vehicle. The vehicle usually restarts, however, you may want to take your vehicle to your dealer before turning off the engine. Service Tire Monitor System If your vehicle has a Tire Pressure Monitor (TPM) system, this message will appear if the TPM system is not working properly. Have your vehicle serviced at your dealer as soon as possible. See Tire Pressure Monitor System on page 405
for more information. Service Transmission This message will display if there is a problem with the transmission of your vehicle. Have your vehicle serviced by your dealer.


236


Service Vehicle Soon This message is displayed when a non-emissions related powertrain malfunction occurs. Have your vehicle serviced by your dealer as soon as possible. Stability System Engaged If your vehicle has StabiliTrak®, this message will be displayed any time StabiliTrak® is actively assisting you with directional control of the vehicle. Slippery road conditions may exist when this message is displayed, so adjust your driving accordingly. This message may stay on for a few seconds after StabiliTrak® stops assisting you with directional control of the vehicle. See StabiliTrak® System on page 299 for more information. Stability System Off If your vehicle has StabiliTrak®, this message will be displayed any time you turn off StabiliTrak® using the TC (traction control) on/off button. See Traction Control System (TCS) (CTS) on page 295
or Traction Control System (TCS) (CTS-V) on page 297 for more information. When this message has been displayed, StabiliTrak® is no longer available to assist you with directional control of the vehicle. Adjust your driving accordingly.


Stability System Ready If your vehicle has StabiliTrak®, this message will be displayed any time you turn StabiliTrak® on again using the TC (traction control) on/off button. See Traction Control System (TCS) (CTS) on page 295 or Traction Control System (TCS) (CTS-V) on page 297 for more information. When this message has been displayed, StabiliTrak® is ready to assist you with directional control of the vehicle, if needed. Starting Disabled – Remove Key This message will appear when the vehicle theft-deterrent system detects that an improper ignition key is being used to try to start the vehicle. Check the ignition key for damage. If it is damaged, it may need to be replaced. If it is not damaged, remove the key and try to start the vehicle again. If it still does not start, try another ignition key or have your vehicle serviced by your dealer. Starting Disabled – Throttle Problem This message appears when your vehicle’s throttle system is not functioning properly. Have your vehicle serviced by your dealer.


237


Trans (Transmission) Hot – Idle Engine This message indicates that the transmission fluid in your vehicle is too hot. Stop the vehicle and allow it to idle until the transmission cools down or until this message is removed. See also Transmission Fluid Hot Message on page 214 for more information. Trunk Open When this message appears on the display, it means that the trunk lid of your vehicle was not closed completely. You should make sure that the trunk lid is closed completely. Turn Signal On If you drive your vehicle for more than about 1 mile (1.6 km) with a turn signal on, this message will appear as a reminder to turn off the turn signal. A multiple chime will sound when this message is displayed.


Theft Attempted This message is displayed if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. Top Speed – Fuel Cut Off This message will appear when the Engine Control Module (ECM) detects that the maximum speed for your vehicle has been reached. Your vehicle’s top speed is based on the top speed rating of the tires. This ensures that your vehicle stays in a safe operating range for the tires. Traction Engaged This message will appear when the Traction Control System (TCS) is actively limiting wheel spin. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly. The message will stay on for a few seconds after the TCS stops limiting wheel spin. See Traction Control System (TCS) (CTS) on page 295 or Traction Control System (TCS) (CTS-V) on page 297 for more information.


238


DIC Vehicle Personalization If your vehicle has the navigation system, see the navigation system manual for instructions on operating the DIC for your vehicle. Your vehicle has personalization that allows you to program certain features to a preferred setting for up to two people. The number of programmable features varies depending upon which model of the vehicle is purchased. On all vehicles, features such as climate control settings, radio preset settings, exterior lighting at unlock, remote lock and unlock confirmation, and automatic door locks have already been programmed for your convenience. Some vehicles have additional features that can be programmed including the seat and outside rearview mirror position. If your vehicle has the ability to program additional personalization features, the driver’s preferences are recalled by pressing the unlock button on the Remote Keyless Entry (RKE) transmitter, 1 or 2, or by pressing the appropriate memory button, 1 or 2, located on the driver’s door. Certain features can be programmed not to recall until the key is placed in the ignition. To change feature preferences, see “Entering the Personalization Menu” following.


Entering the Personalization Menu To enter the feature programming mode, use the following procedure: 1. Turn the ignition to ON, but do not start the


engine. Make sure an automatic transmission is in PARK (P) or a manual transmission has the parking brake set. To avoid excessive drain on the battery, it is recommended that the headlamps are turned off.


2. If your vehicle has memory settings, press the appropriate memory button, 1 or 2, located on the driver’s door armrest. The DIC display will show either Driver 1 or 2 depending on which button was selected.


3. Press the PWR/VOL knob to turn the


radio on.


4. Press the TUNE/SEL knob once to access the


main menu of the DIC.


5. Turn the TUNE/SEL knob until SETUP is


highlighted.


6. Press the TUNE/SEL knob once to access the


SETUP menu.


239


7. Turn the TUNE/SEL knob until the feature you


want to change is highlighted, then press the TUNE/SEL knob to turn the feature on or off. If the feature is turned on, a check mark will appear next to the feature name. If none of the personalization items are turned on, turn on the personalization menu by pressing the TUNE/SEL knob. The list of features will then appear, and you can repeat Step 6.


Personalization Features The following choices are available for programming: Personalization Name This feature allows you to type in a name that will appear on the DIC display whenever the corresponding Remote Keyless Entry (RKE) transmitter is used or one of the buttons on the driver’s door armrest (1 or 2) is pressed. If a customized name is not programmed, the system will show DRIVER 1 or DRIVER 2
to correspond with the numbers on the back of the RKE transmitters.


To program a name, use the following procedure: 1. Enter the Personalization menu following


the instructions listed previously.


2. Select the PERSONALIZATION NAME menu


item by pressing the TUNE/SEL knob once. You will see a cursor on the screen.


3. Turn the TUNE/SEL knob until you reach the


first letter you want. The letter will be highlighted. There is a complete alphabet with both upper and lower case letters and the numbers zero through nine. Also included are spaces and other non-letter characters such as the ampersand (&).


4. Press the TUNE/SEL knob once to select the


letter. The letter will then appear on the display. If you make a mistake, press the CLR button. This will exit the menu. You can then go back into the menu and edit the name. You can also press the TUNE/SEL knob repeatedly to cycle through all the characters until you reach the character you wish to change. 5. Repeat Steps 3 and 4 until the name you want is complete. You can program up to 16 characters.


240


The name you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. To program the next feature, enter the personalization portion of the SETUP menu following the instructions listed previously. Configure Display Keys This feature allows you to customize the functions of the four soft keys located to the left and right of the audio display. See “Configurable Radio Display Keys” under Radio with CD on page 260
for programming information. Configure SWC (Steering Wheel Controls) Keys This feature allows you to customize the functions of the four steering wheel controls located on the left spoke of the steering wheel. See Reconfigurable Steering Wheel Controls (SWC) (CTS) on page 161 for programming information.


Remote Recall Memory If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat and mirror controls when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


241


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until REMOTE


RECALL MEMORY is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Remote Exit Recall or Key In Recall Memory cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Remote Exit Recall If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver’s seat when the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


242


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until REMOTE EXIT


RECALL is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Remote Recall Memory cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Key in Recall Memory If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat and mirror positions when the key is inserted into the ignition. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


243


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until KEY IN


RECALL MEMORY is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Remote Recall Memory cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Auto Exit Seat If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver’s seat when the key is removed from the ignition and the driver’s door is opened. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


244


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until AUTO EXIT


SEAT is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear in the box next to the feature name. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Twilight Delay This feature allows you to set the amount of time you want the exterior lamps to remain on after you exit the vehicle. Programmable Modes


Mode 1: 0:00 seconds


Mode 2: 0:15 seconds


Mode 3: 0:30 seconds


Mode 4: 1:00 minute


Mode 5: 1:30 minutes


Mode 6: 2:00 minutes


Mode 7: 2:30 minutes


Mode 8: 3:00 minutes Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since the vehicle left the factory.


245


To determine the mode to which the vehicle is programmed or to program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until TWILIGHT


DELAY is highlighted.


3. Press the TUNE/SEL knob to scroll through


and select the available delay settings. If you choose Mode 1, the exterior lamps will not illuminate when you exit the vehicle. Only one mode can be selected at a time.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Lights Flash at Unlock This feature flashes the exterior lamps when the Remote Keyless Entry (RKE) transmitter is used to unlock the vehicle. The lamps will flash for approximately 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON, or START, or the RKE transmitter is used to lock the vehicle. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory.


246


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until LIGHTS


FLASH AT UNLOCK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Lights Flash at Lock This feature allows the exterior lamps to flash once when the Remote Keyless Entry (RKE) transmitter is used to lock the vehicle. All doors must be closed for this feature to work, and the lamps will not flash if the parking lamps or headlamps are on. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory.


247


Horn Sounds at Lock This feature sounds the horn once when the Remote Keyless Entry (RKE) transmitter is used to lock the vehicle. All doors must be closed for this feature to work. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until LIGHTS


FLASH AT LOCK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


You can select this feature by itself, or you can combine it with Horn Sounds At Lock so that both the lights flash and the horn chirps when you lock your vehicle. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


248


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until HORN


SOUNDS AT LOCK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If you select this feature to be on, Lights Flash At Lock will also be on. You can choose Lights Flash At Lock by itself, but Horn Sounds At Lock will always have Lights Flash At Lock enabled when it is selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Exterior Lights at Unlock This feature turns on the exterior lamps when the Remote Keyless Entry (RKE) transmitter is used to unlock the vehicle. The lamps will remain on for about 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON, or START, or the RKE transmitter is used to lock the vehicle. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory.


249


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until EXT. LIGHT


AT UNLOCK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Driver Unlock in Park (Automatic Transmission Only) The feature allows the driver’s door to automatically unlock when the transmission is shifted into PARK (P). Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


250


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until DRIVER


UNLOCK IN PARK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Driver Unlock Key Out/Off, Doors Unlock Key Out/Off, or Doors Unlock in Park cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Driver Unlock Key Out Automatic Transmission Only/Driver Unlock Key Off (Manual Transmission Only) This feature allows the driver’s door to automatically unlock when the key is removed from the ignition on automatic transmission vehicles or when the ignition is turned to OFF for manual transmission vehicles. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


251


Doors Unlock in Park (Automatic Transmission Only) The feature allows the doors to automatically unlock when the transmission is shifted into PARK (P). Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until DRIVER UNLOCK KEY OUT/OFF is highlighted.


3. Press the TUNE/SEL knob to switch between


on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Driver Unlock in Park (automatic transmission), Doors Unlock in Park (automatic transmission), or Doors Unlock Key Out/Off cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


252


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until DOORS


UNLOCK IN PARK is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Doors Unlock Key Out/Off, Driver Unlock Key Out/Off, or Driver Unlock in Park (automatic transmission) cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Doors Unlock Key Out (Automatic Transmission Only)/ Doors Unlock Key Off (Manual Transmission Only) This feature allows the doors to automatically unlock when the key is removed from the ignition on automatic transmission vehicles or when the ignition is turned to OFF on manual transmission vehicles. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


253


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until DOORS UNLOCK KEY OUT/OFF is highlighted.


3. Press the TUNE/SEL knob to switch between


on and off. When the mode is turned on, a check mark will appear next to the feature name.


If this feature is selected, Doors Unlock in Park (automatic transmission), Driver Unlock in Park (automatic transmission), or Driver Unlock Key Out/Off cannot be selected. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Delayed Locking This feature delays the locking of the vehicle’s doors for up to five seconds after a power door lock switch or the lock button on the Remote Keyless Entry (RKE) transmitter is pressed. The five second delay occurs after the last door is closed. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory.


254


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until DELAYED


LOCKING is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Lock Passenger Window This feature allows you to disable either all the passenger window switches or the rear passenger window switches only. If this feature is turned on, all passenger window switches will be disabled when the window lockout button is pressed. If the feature is off, only the rear passenger window switches will be disabled. See Power Windows on page 104 for more information. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


255


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until LOCK PASS


WINDOW is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Mirror to Curb in Reverse If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, the passenger’s outside rearview mirror will move downward so you can view the curb when the shift lever is shifted into REVERSE (R). The mirror will return to the last known driving position when the shift lever is moved out of REVERSE (R). See Outside Curb View Assist Mirror on page 136 for more information. Programmable Modes


Mode 1: ON


Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.


256


To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until MIRROR TO


CURB IN REV is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between on and off. When the mode is turned on, a check mark will appear next to the feature name.


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.


Enhanced Chime Volume This feature allows you to adjust the volume level of the vehicle’s warning chimes. The chime volume cannot be turned off, only adjusted. Programmable Modes


Mode 1: NORMAL


Mode 2: LOUD Before your vehicle was shipped from the factory, it was programmed to Mode 1. The mode to which the vehicle was programmed may have been changed since it left the factory. To program the vehicle to a different mode, use the following procedure: 1. Enter the personalization portion of the SETUP menu following the instructions listed previously.


2. Turn the TUNE/SEL knob until ENHANCED


CHIME VOLUME is highlighted.


3. Press the TUNE/SEL knob to switch back and


forth between the normal and loud settings.


257


The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle. Exiting the Personalization Menu To exit the personalization portion of the SETUP menu, press the CLR button once you have finished making your selections. You will return to the main audio screen. If a 15 second time period has elapsed with no selection made, the SETUP menu will be exited automatically.


Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. Driving without distraction is a necessity for a safer driving experience. See Defensive Driving on page 288. By taking a few moments to read this manual and get familiar with your vehicle’s audio system, you can use it with less effort, as well as take advantage of its features. While your vehicle is parked, set up your audio system by presetting your favorite radio stations, setting the tone and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite stations using the presets and steering wheel controls if the vehicle has them.


258


{CAUTION:


This system provides you with a far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed. Always keep your eyes on the road and your mind on the drive — avoid engaging in extended searching while driving.


Keeping your mind on the drive is important for safe driving. For more information, see Defensive Driving on page 288. Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: (cid:127) Familiarize yourself with all of its controls. (cid:127) Familiarize yourself with its operation.


(cid:127) Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers. Then, when driving conditions permit, you can tune to your favorite radio stations using the presets and steering wheel controls if the vehicle has them.


Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer. Also, check federal rules covering mobile radio and telephone units. If sound equipment can be added, it is very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, radio, or other systems, and even damage them. Your vehicle’s systems may interfere with the operation of sound equipment that has been added. Your vehicle has a feature called Retained Accessory Power (RAP). With RAP, the audio system can be played even after the ignition is turned off. See Retained Accessory Power (RAP) on page 114 for more information.


259


Radio with CD


Radio with CD shown, Radio with Six-Disc CD


similar


Setting the Time 1. Press the TUNE/SEL (select) knob to enter


the main menu.


2. Turn the TUNE/SEL knob until SET CLOCK


appears on the display.


3. Press the TUNE/SEL knob to select


SET CLOCK.


4. Turn the TUNE/SEL knob to adjust the time. 5. Press the TUNE/SEL knob to update the


time. VEHICLE TIME UPDATED will appear on the display.


If the CLOCK/RADIO DISP (display) is configured into one of the configurable keys, pressing the key will switch the display between the radio station frequency and the time. See “Configurable Radio Display Keys” under Radio with CD on page 260 for more information on configuring the keys.


260


XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous United States and Canada. XM™ offers a large variety of coast-to-coast channels including music, news, sports, talk, traffic/weather (U.S. subscribers), and children’s programming. XM™ provides digital quality audio and text information that includes song title and artist name. A service fee is required in order to receive the XM™ service. For more information, contact XM™; In the U.S. at www.xmradio.com or call 1-800-852-XMXM (9696) or in Canada at www.xmradio.ca or call 1-877-GET-XMSR (438-9677).


CLOCK/INFO DISP (Clock/Information Display): Press the CLOCK/INFO DISP button to switch between the clock display, the XM™ screen, and the XM™ information display.


Radio Data System (RDS) The audio system has a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, the radio can do the following: (cid:127) Seek to stations broadcasting the selected


type of programming


(cid:127) Receive announcements concerning local and


national emergencies


(cid:127) Display messages from radio stations (cid:127) Seek to stations with traffic announcements This system relies upon receiving specific information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station. While the radio is tuned to an RDS station, the station name or call letters will appear on the display instead of the frequency. RDS stations may also provide the time of day, a program type (PTY) for current programming, and the name of the program being broadcast.


261


Press this button while in XM™ mode to retrieve three different categories of information related to the current song or channel: Artist, Song Title, and Category. To view this information, perform the following: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until CLOCK/INFO


DISP appears on the display.


3. Press the TUNE/SEL knob to select


CLOCK/INFO DISP. The display will change to show the additional XM™ information. 4. To return to the original display, press the


CLR (clear) button or wait for the display to time out.


If the CLOCK/INFO DISP is configured into one of the configurable keys, pressing the key will switch the display between the radio station frequency and the time. See “Configurable Radio Display Keys” later in this section for more information.


262


Playing the Radio


PWR (Power): Press this knob to turn the system on and off.


VOL (Volume): Turn this knob to increase or to decrease the volume.


AVC (Automatic Volume Compensation): Available only with the premium Bose® audio system. AVC, which utilizes Bose AudioPilot® noise compensation technology, continuously adjusts the audio system equalization, to compensate for background noise, so that your music always sounds the same at the set volume level. This feature is most effective at lower radio volume settings where background noise can affect how well you hear the music being played through your vehicle’s audio system. At higher volume settings, where the music is much louder than the background noise, there may be little or no adjustments by AVC. To turn AVC on and off, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until AUTO


VOLUME COMP. appears on the display.


Q SCAN R: Press the SCAN button to enter scan mode. SCAN will appear on the display. Press the up arrow to scan to the next station. The radio will go to a station, play for five seconds, then go on to the next station. Press this button again to stop scanning. To scan preset stations, press and hold SCAN for more than two seconds until you hear a beep and PSCAN appears on the display. The radio will go to the first preset station stored on your firm keys, play for five seconds, then go on to the next preset station. Press SCAN again to stop scanning presets. The radio will only scan stations with a strong signal that are in the selected band.


3. Press the TUNE/SEL knob to turn AVC on or off. An X will appear in the box when AVC is selected on.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


SOURCE: Press this button to select a source, either radio or CD. The CD must be loaded to select the source and to play. CD will appear on the display if a CD is loaded. If a CD is not loaded the display will not change from the radio source. Finding a Station


BAND: Press this button to select FM1, FM2, AM, or XM1 or XM2 (if equipped). Q SEEK R: Press the up or the down arrow to go to the next or to the previous station and stay there. SEEK will appear on the display. The sound will mute while seeking. The radio will only seek stations with a strong signal that are in the selected band.


263


Setting Preset Stations Up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (if equipped)), can be programmed on the six numbered firm keys, by performing the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, or AM, or


XM1 or XM2.


3. Tune in the desired station. 4. Press and hold one of the six numbered firm keys for two seconds until you hear a beep. The set preset station number will appear on the display above the firm key that it is set to. Whenever that numbered firm key is pressed for less than two seconds, the station that was set will return.


LOCAL/DISTANT Selection: With this feature you can set the radio to search for local stations or stations that are further away for a larger selection. To set this feature to LOCAL or DISTANT, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until SEEK LOCAL


or SEEK DISTANT appears on the display. 3. Press the TUNE/SEL knob to select either


LOCAL or DISTANT.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


To search for stations, press the SEEK up or down arrows. If the system is set to LOCAL, SEEK will appear in the display and seek to stations with strong signals only. If the system is set to DISTANT, D-SEEK will appear in the display and seek to stations with weak and strong signals.


264


5. Repeat the steps for each firm key.


To set the preset stations with an equalization setting, DSP (digital signal processing) setting, or a program type (PTY) setting, see each of these features later in this section. When a preset station is selected, once one of these additional settings is selected, the preset station will remember each setting and it will remain active, until the setting is selected off for that preset station.


AUTOSTORE PRESETS: To set the preset stations automatically, perform the following steps: 1. Turn the radio on. 2. Press BAND to select FM1, FM2, or AM. 3. Press the TUNE/SEL knob to enter the


main menu.


4. Turn the TUNE/SEL knob until AUTOSTORE


PRESETS appears on the display.


5. Press the TUNE/SEL knob to select.


AUTOSTORE will appear on the display. The radio will automatically search the band and select and store the six radio stations with the strongest signal. The stations will be stored by signal strength, not sequential order. The set preset station number will appear on the display above the firm key that it is set to. Whenever that numbered firm key is pressed for less than two seconds, the station that was set will return.


6. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


When battery power is removed and later applied, you will not have to reset your radio presets.


265


PRESETS HOME/AWAY: This feature gives you the ability to store two different kinds of station presets. HOME can be used for stations available where you live and AWAY can be for stations available outside of your local broadcasting area. To set preset stations for home and away perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until PRESETS


HOME/AWAY appears on the display.


3. Press the TUNE/SEL knob to select. HOME


or AWAY will appear on the display.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


Follow the manual or automatic steps previously listed for setting the preset firm keys for both home and away.


266


Setting the Tone (Bass/Treble) To adjust the bass, midrange, and treble, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until


BASS-MID-TREBLE appears on the display. 3. Press the TUNE/SEL knob to enter the tone


settings.


4. Press the TUNE/SEL knob to scroll through


the settings.


5. Turn the TUNE/SEL knob to increase or to decrease the bass, midrange, or treble. If a station is weak or noisy, decrease the treble.


6. Press the TUNE/SEL knob to set the


adjustment.


7. Press the CLR button to exit the display. To return to the original display repeatedly press the CLR button or wait for the display to time out.


AUDIO EQUALIZER: This feature allows you to select customized equalization settings. To choose an equalization setting (EQ0 through EQ5), perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until EQUALIZER


appears on the display.


3. Press the TUNE/SEL knob to set the


equalization setting. The equalization setting will appear on the display.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


The equalization settings are preset to EQ0 (Normal), EQ1 (Pop), EQ2 (Rock), EQ3 (Jazz), EQ4 (Talk), and EQ5 (Country).


Adjusting the Speakers (Balance/Fade) To adjust the balance or fade, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until


BASS-MID-TREBLE appears on the display. 3. Press the TUNE/SEL knob to enter the tone


settings.


4. Press the TUNE/SEL knob to scroll to


BALANCE or FADER.


5. Turn the TUNE/SEL knob to adjust the


BALANCE to the right or the left speakers and the FADER to the front or the rear speakers.


6. Press the TUNE/SEL knob to set the


adjustment.


7. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


EQ0 will not appear on the display when in this mode.


267


TALK: This setting should be used when listening to non-musical material such as news, talk shows, sports broadcasts, and books on tape. Talk makes spoken words sound very clear.


SPACIOUS: This setting is used to make the listening space seem larger.


REAR SEAT: This setting adjusts the audio to give the rear seat passenger(s) the best possible sound quality. Sound quality for the front seat passengers may be different when this setting is used.


DRIVER SEAT: This setting adjusts the audio to give the driver the best possible sound quality. Sound quality for the front and rear seat passenger(s) may be different when this setting is used.


Using Digital Signal Processing (DSP) Available only with the premium Bose® audio system, this feature is used to provide a choice of five different listening experiences: DSP normal, talk, spacious, rear seat, and driver seat. DSP can be used while listening to the radio or the CD player. The radio keeps separate DSP settings for each band, preset, and source. To select a DSP choice, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until one of the five


settings appears on the display.


3. Press the TUNE/SEL knob to select a DSP


setting.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


DSP NORMAL: This setting provides the best overall audio performance for all passengers. DSP NORMAL will not appear on the display when in this mode.


268


RDS Messages The RDS message feature is available only on FM stations that broadcast RDS information. See Radio Data System (RDS) for more information earlier in this section.


ALERT: Alert warns of local and national emergencies. When, an alert announcement comes on the current radio station or a related network station, ALERT will appear on the display. You will hear the announcement, even if the volume is low or a CD is playing. If a CD is playing, play will stop during the announcement. Alert announcements cannot be turned off. If the radio tunes to a related network station for the announcement, it will return to the original station when the announcement is finished. ALERT will not be affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.


MSG (Message): If the current RDS station has a message, MSG will appear on the display. The message may display the artist, song title, call in phone numbers, etc. If the entire message does not appear on the display, parts of the message will appear every three seconds until the message is completed. Once the completed message has been displayed, MSG will disappear from the display until another new message is received. To display the last message, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until CLOCK/INFO


DISP appears on the display.


3. Press the TUNE/SEL knob. The message will


appear on the display.


Once the message has been displayed, MSG will disappear from the display until another new message is received.


269


TP (Traffic Program): TP will appear on the display when the radio detects a signal from an RDS station that has traffic announcement broadcast capability.


TA (Traffic Announcement): If TA appears on the display, the tuned radio station broadcasts traffic announcements and when a traffic announcement comes on the tuned station you will hear it. If the station does not broadcast traffic announcements, when TA is turned on it will seek to a station that does. When a station that broadcasts traffic announcements is found, the radio will stop seeking and TA will appear on the display. If no station is found that broadcasts traffic announcements, No Traffic will appear on the display. The radio will play traffic announcements if the volume is low. The radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements.


To turn TA on or off, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until TRAFFIC


ANNOUNCE appears on the display.


3. Press the TUNE/SEL knob to select ON or


OFF. An X will appear in the box when TA is selected on.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


Activating Category (CAT) Stations (RDS and XM™) CAT allows you to search for stations with specific types of music. The selectable categories are POP, EASY, TALK, CNTRY (Country), CLASS (Classical), and JAZZ.


270


To activate program types, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until CATEGORY


appears on the display.


3. Press the TUNE/SEL knob to select ON or


OFF. An X will appear in the box when CAT is selected on.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


Once CAT is activated the categories will appear on the display above the firm keys, in place of the preset stations, if programmed. Press the firm key for the category that you would like to listen to. Not all stations support CAT. The radio may not go to all of the stations with that music type when pressing the firm key.


AF (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same category. To turn AF on or off, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until ALTERNATE


FREQ. appears on the display.


3. Press the TUNE/SEL knob to select AF OFF,


AF ON, or AF REG. An X will appear in the box when AF is selected on.


4. Press the CLR button to exit the display. To


return to the original display, repeatedly press the CLR button or wait for the display to time out.


This function does not apply for XM™ Satellite Radio Service.


271


Radio Message


THEFTLOCK: This message is displayed when the THEFTLOCK® system has been activated. Take the vehicle to the dealer for service. Radio Messages for XM™ Only See XM Radio Messages on page 279 later in this section for further detail. Using the Single CD Player Insert a CD partway into the slot, label side up. The player will pull it in. If the ignition and the radio are on the CD will begin playing. A CD may be loaded with the radio off but it will not start playing until the radio is on. If the ignition or radio is turned off with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start to play where it stopped, if it was the last selected audio source. When the CD is inserted, CD will appear on the display. As each new track starts to play, the track number will appear on the display.


The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring. Full-size CDs and the smaller CDs are loaded in the same manner. If playing a CD-R, the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. There may be an increase in skipping, difficulty in finding tracks, and/or difficulty in loading and ejecting. If these problems occur, check the bottom surface of the CD. If the surface of the CD is damaged, such as cracked, broken, or scratched, the CD will not play properly. If the surface of the CD is soiled, see Care of Your CDs on page 285 for more information. If there is no apparent damage, try a known good CD. Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen instead.


272


If you add any label to a CD, insert


Notice: more than one CD into the slot at a time, or attempt to play scratched or damaged CDs, you could damage the CD player. When using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error appears on the display, see “CD Messages” later in this section. When a CD is inserted the CD functions will appear on the display above the firm keys, in place of the preset stations (if programmed).


F1 PREV (Previous): Press this firm key to go to the previous track. Press and hold this firm key to reverse quickly within a track. Release the firm key to play the passage. The elapsed time of the track will appear on the display.


F2 NEXT: Press this firm key to go to the next track. Press and hold this firm key to advance quickly within a track. Release the firm key to play the passage. The elapsed time of the track will appear on the display.


F3 RDM (Random): Press this firm key to listen to the tracks in random, rather than sequential, order. RANDOM will appear on the display. Press RDM again to turn off random play. RANDOM will disappear from the display.


F4 RPT (Repeat): Press this firm key to hear a track over again. REPEAT will appear on the display. Press RPT again to turn off repeat play. REPEAT will disappear from the display.


F6 DISP (Display): Press this firm key to display the time of the track. Press this firm key again to remove the time of the track from the display. Q SEEK R: Press the up or the down arrow to go to the next or to the previous track on the CD. Q SCAN R: Press this button to listen to each track for 10 seconds. The CD will go to a track, play for 10 seconds, then go on to the next track. Press this button again to stop scanning. X (Eject): Press this button to stop a CD when it is playing or to eject a CD when it is not playing. Eject may be activated with the ignition and the radio off.


273


If you add any label to a CD, insert


Notice: more than one CD into the slot at a time, or attempt to play scratched or damaged CDs, you could damage the CD player. When using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error appears on the display, see “CD Messages” later in this section. When a CD is inserted the CD functions will appear on the display above the firm keys, in place of the preset stations, if programmed.


LOAD: Press the LOAD button to load CDs into the CD player. This CD player will hold up to six CDs.


Using the Six-Disc CD Changer The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring. Full-size CDs and the smaller CDs are loaded in the same manner. If playing a CD-R, the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. There may be an increase in skipping, difficulty in finding tracks, and/or difficulty in loading and ejecting. If these problems occur, check the bottom surface of the CD. If the surface of the CD is damaged, such as cracked, broken, or scratched, the CD will not play properly. If the surface of the CD is soiled, see Care of Your CDs on page 285 for more information. If there is no apparent damage, try a known good CD. Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen instead.


274


To insert one CD, do the following: 1. The ignition and the radio can be on or off. 2. Press and release the LOAD button. Please


Wait will appear on the display.


3. Load the CD, when INSERT appears on the


display, insert a CD partway into the slot, label side up. The player will pull the CD in.


When a CD is inserted, CD will appear on the display, the number of the CD and the track number will appear on the display if the radio is on. If the radio is on, the CD will begin to play automatically. To insert multiple CDs, do the following: 1. The ignition and the radio can be on or off. 2. Press and hold the LOAD button for


two seconds. Please Wait will appear on the display and you will hear a beep.


3. Load the CD, when INSERT appears on the


display, insert a CD partway into the slot, label side up. The player will pull the CD in. Do not try to load two CDs at one time and wait to load a CD until INSERT appears on the display for each disc inserted. The CD player will take up to six CDs. Do not try to load more than six. If you want to load less than six CDs, load the desired amount. The CD player will time out when it does not receive any more CDs and the last CD loaded will begin to play.


If the radio is on, the last CD loaded will begin to play automatically. F1 CD n (Down): Press this firm key to go to the previous CD. F2 CD m (Up): Press this firm key to go to the next CD. CD REV { (Reverse): Press this firm key to go to the previous track. Press and hold this firm key to reverse quickly within the track. Release the firm key to play the passage. The elapsed time of the track will appear on the display.


275


CD FWD | (Forward): Press this firm key to go to the next track. Press and hold this firm key to advance quickly within the track. Release the firm key to play the passage. The elapsed time of the track will appear on the display.


F5 MODE: Press this firm key to select from NORMAL, RPT TRCK (Repeat Track), RPT CD (Repeat CD), RDM TRK (Random Track), and RDM ALL (Random All CDs). (cid:127) NORMAL: Sets the system for normal play of


the CD(s). NORMAL will not appear on the display when in this mode.


(cid:127) RPT TRCK (Repeat Track): Repeats the


track over again. RPT TRCK will appear on the display. Press the MODE firm key again to turn off repeat play. RPT TRCK will disappear from the display.


(cid:127) RPT CD (Repeat CD): Repeats the CD over again. RPT DISC will appear on the display. Press the MODE firm key again to turn off repeat play. RPT DISC will disappear from the display.


(cid:127) RDM TRK (Random Track): Plays the tracks


on the current CD in random, rather than sequential, order. RDM TRK will appear on the display. Press the MODE firm key again to turn off random play. RDM TRK will disappear from the display.


(cid:127) RDM ALL (Random All CDs): Plays all of the CDs loaded in random, rather than sequential, order. RDM ALL will appear on the display. Press the MODE firm key again to turn off random play. RDM ALL will disappear from the display.


F6 DISP (Display): Press this firm key to display the time of the track. Press this firm key again to display CD PLAY and press this firm key once more to clear the display. Q SEEK R: Press the up or the down arrow to go to the next or to the previous track on the CD. Q SCAN R: Press this button to listen to each track for 10 seconds. The CD will go to a track, play for 10 seconds, then go on to the next track. Press this button again to stop scanning.


276


X (Eject): Press this button to eject the CD that is currently playing, or press and hold this button to eject all of the CDs loaded. You will hear a beep. Eject may be activated with the ignition or radio off. CD Messages If the CD comes out, it could be for one of the following reasons: (cid:127)


If it is very hot. When the temperature returns to normal, the CD should play. If you are driving on a very rough road. When the road becomes smoother, the CD should play.


(cid:127)


(cid:127) The CD is dirty, scratched, wet, or


upside down.


(cid:127) The air is very humid. If so, wait about an


hour and try again.


(cid:127) There may have been a problem while


burning the CD.


(cid:127) The label may be caught in the CD player. If the CD is not playing correctly, for any other reason, try a known good CD. If any error occurs repeatedly or if an error cannot be corrected, contact your GM dealer. If the radio displays an error message, write it down and provide it to your GM dealer when reporting the problem.


277


Configurable Radio Display Keys This feature allows you to customize the four keys that are located on each side of the radio display to make it easier to adjust the radio features. Other non-radio related features are also available for customization. To program the configurable radio display keys, perform the following steps: 1. Press the TUNE/SEL knob to enter the


main menu.


2. Turn the TUNE/SEL knob until SETUP


appears on the display.


3. Press the TUNE/SEL knob to enter into


SETUP.


4. Turn the TUNE/SEL knob until CONFIGURE


DISPLAY KEYS appears on the display. 5. Press the TUNE/SEL knob to enter into


CONFIGURE DISPLAY KEYS.


6. Turn the TUNE/SEL knob to select which of the four configurable keys you would like to change. The currently assigned feature will be shown.


7. Press the TUNE/SEL knob to select the


configurable key to change.


8. Turn the TUNE/SEL knob to find the feature


that you would like to store to the key.


9. Press the TUNE/SEL knob when you have found the feature to be stored. The display will update, by showing the symbol of the feature that you selected next to the configurable key.


10. Repeat the previous steps for each


configurable key.


Once a feature is programmed to a key, the feature will not appear on the display when programming the remaining configurable keys. The configurable keys can be changed at any time.


278


XM Radio Messages


Radio Display Message


Condition


Action Required


XL (Explicit Language Channels)


XL on the radio display, after the channel name, indicates content with explicit language.


These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696).


Updating


Updating encryption code The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds.


No Signl


Loss of signal


The system is functioning correctly, but the vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return.


Loading


Off Air


CH Unavl


No Info


No Info


Acquiring channel audio (after 4 second delay)


The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly.


Channel not in service


This channel is not currently in service. Tune in to another channel.


Channel no longer available


This previously assigned channel is no longer assigned. Tune to another station. If this station was one of the presets, choose another station for that preset button.


Artist Name/Feature not available


No artist information is available at this time on this channel. The system is working properly.


Song/Program Title not available


No song title information is available at this time on this channel. The system is working properly.


279


Radio Display Message


Condition


Action Required


No Info


NotFound


No Info


XM Lock


Category Name not available


No category information is available at this time on this channel. The system is working properly.


No channel available for the chosen category


There are no channels available for the selected category. The system is working properly.


No Text/Informational message available


No text or informational messages are available at this time on this channel. The system is working properly.


Theft lock active


The XM™ receiver in your vehicle may have previously been in another vehicle. For security purposes, XM™ receivers cannot be swapped between vehicles. If this message is received after having your vehicle serviced, check with your GM dealer.


If tuned to channel 0, this message will alternate with the XM Radio 8 digit radio ID label. This label is needed to activate the service.


If this message is received when tuned to channel 0, there may be a receiver fault. Consult with your GM dealer.


If this message does not clear within a short period of time, the receiver may have a fault. Consult with your GM dealer.


Radio ID


Radio ID label (channel 0)


Unknown


Check XM


Radio ID not known (should only be if hardware failure)


Hardware failure


280


Navigation/Radio System Your vehicle may have a navigation radio system. The navigation system has built-in features intended to minimize driver distraction. Technology alone, no matter how advanced, can never replace your own judgment. See the Navigation System manual for some tips to help you reduce distractions while driving.


Theft-Deterrent Feature THEFTLOCK® is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identification Number (VIN). If the radio is moved to a different vehicle, it will not operate. If the radio is removed from your vehicle, the original VIN in the radio can be used to trace the radio back to your vehicle. With THEFTLOCK® activated, the radio will not operate if stolen.


Audio Steering Wheel Controls (CTS)


Some audio functions can be adjusted at the steering wheel. They include the following:


Volume: Turn this knob to increase or to decrease the volume. e(Band/Source): Press this button to switch between FM1, FM2, AM, or XM1 or XM2
(if equipped), radio, or CD. For vehicles with the six-disc CD changer radio: If none of the audio sources are loaded, and this button is pressed, NO SOURCE LOADED will appear on the display.


281


g(Mute/Voice Recognition): Press this button to silence the system. Press this button again or turn the VOL (volume) knob to turn the sound on. If your vehicle has the navigation system, press this button to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information.


Audio Steering Wheel Controls (CTS-V)


See Reconfigurable Steering Wheel Controls (SWC) (CTS) on page 161 for more information on this feature.


Depending on your vehicle, the audio steering wheel controls may be different. For the CTS-V, some audio controls can be adjusted at the steering wheel. They include the following:


0 (Mute): Press this button to silence the system. Press this button again, or any other radio button, to turn the sound on.


282


SRCE (Source): Press this button to switch between FM1, FM2, AM, or XM1 or XM2
(if equipped), radio, or CD. g(OnStar®/Voice Recognition): If your vehicle has the Radio with CD or Radio with Six-Disc CD audio system, press this button to interact with the OnStar system. If your vehicle has the navigation system, press this button to initiate voice recognition. See “Voice Recognition” in the Navigation System manual for more information. While in Voice Recognition, say “OnStar” to interact with the OnStar® system. See the OnStar® System on page 137 in this manual for more information.


1-6 (Preset Stations): Press this button to play stations that are programmed on the radio preset pushbuttons. The radio will only seek preset stations with a strong signal that are in the selected band. When a CD is playing, press this button to go to the next track. When a CD is playing in the six-disc CD changer, press this button to go to the next available CD, if multiple CDs are loaded.


+ u — (Volume): Press this button to increase or to decrease the volume. + t u — (Seek): Press either arrow to go to the next or the previous radio station and stay there. The radio will only seek stations with a strong signal that are in the selected band. When a CD is playing, press the minus sign to go to the start of the current track, if more than 10 seconds have played. Press the plus sign to go to the next track. If either the minus or the plus button are pressed more than once, the player will continue moving backward or forward through the CD. Press and hold the SEEK plus or minus button, until you hear a beep. The CD will fast forward or fast reverse through the CD. Press either button again to play the passage. If you have the navigation system, some of the audio steering wheel controls work when a DVD is playing in the navigation radio. See the Navigation System manual for more information.


283


Radio Reception You may experience frequency interference and static during normal radio reception if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations will boost the power levels during the day, and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on your radio.


FM Stereo FM stereo will give the best sound, but FM signals will reach only about 10 to 40 miles (16 to 65 km). Tall buildings or hills can interfere with FM signals, causing the sound to fade in and out. XM™ Satellite Radio Service XM™ Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of XM signal for a period of time. The radio may display No Signl to indicate interference.


284


Cellular Phone Usage Cellular phone usage may cause interference with your vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off.


Care of Your CDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom surface of the disc. If the surface of a CD is damaged, such as cracked, broken, or scratched, the CD will not play properly or not at all. If the surface of a CD is soiled, take a soft, lint free cloth or dampen a clean, soft cloth in a mild, neutral detergent solution mixed with water, and clean it. Make sure the wiping process starts from the center to the edge. Do not touch the bottom side of a CD while handling it; this could damage the surface. Pick up CDs by grasping the outer edges or the edge of the hole and the outer edge.


Care of the CD Player The use of CD lens cleaners for CD players is not advised, due to the risk of contaminating the internal lens of the CD optics with lubricants.


285


Diversity Antenna System The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the grid lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. Notice: Do not apply aftermarket glass tinting with metallic film. The metallic film in some tinting materials will interfere with or distort the incoming radio reception. Any damage caused to your antenna due to metallic tinting materials will not be covered by your warranty. Notice: Do not try to clear frost or other warranty. If static is heard on the radio, when the rear window defogger is turned on, it could mean that a defogger grid line has been damaged. If this is true, the grid line must be repaired.


If adding an aftermarket cellular telephone to your vehicle, and the antenna needs to be attached to the glass, make sure that the grid lines for the AM-FM antennas are not damaged. Make sure the cellular telephone antenna does not touch a grid line.


XM™ Satellite Radio Antenna System The XM™ Satellite Radio antenna is located on the roof of your vehicle. Keep this antenna clear of snow and ice build up for clear radio reception. If your vehicle has a sunroof, the performance of the XM™ system may be affected if the sunroof is open. Loading items onto the roof of your vehicle can interfere with the performance of the XM™ system. Make sure the XM™ Satellite Radio antenna is not obstructed.


286


Section 4


Driving Your Vehicle


Your Driving, the Road, and


Your Vehicle ............................................ 288
Defensive Driving ...................................... 288
Drunken Driving ........................................ 289
Control of a Vehicle .................................. 292
Braking ...................................................... 292
Anti-Lock Brake System (ABS) .................. 293
Braking in Emergencies ............................. 295
Traction Control System (TCS) (CTS) ........ 295
Traction Control System (TCS) (CTS-V) .... 297
Competitive Driving Mode (CTS-V) ............ 298
Limited-Slip Rear Axle ............................... 299
StabiliTrak® System ................................... 299
Panic Brake Assist .................................... 300

Loading...
x