6. Put the compact spare tire near you.
5-89
8. Remove all the wheel nuts and take off the flat tire.
{CAUTION:
Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.
9. Remove any rust or dirt
from the wheel bolts, mounting surfaces, and spare wheel.
10. Install the spare tire. 11. Put the wheel nuts back on with the rounded end of
the nuts toward the wheel.
12. Tighten each wheel nut by turning it clockwise with
your hand until the wheel is held against the hub.
{CAUTION:
Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off.
5-90
13. Lower the vehicle by turning the wheel wrench
counterclockwise. Lower the jack completely.
{CAUTION:
Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See Capacities and Specifications on page 5-114 for wheel nut torque specification.
Improperly tightened wheel nuts can lead
Notice: to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See Capacities and Specifications on page 5-114 for the wheel nut torque specification.
5-91
14. Tighten the wheel nuts
firmly in a crisscross sequence as shown.
Storing a Flat or Spare Tire and Tools (CTS Only)
{CAUTION:
Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
After you’ve put the compact spare tire on your vehicle, you will need to store the flat tire in your trunk. Remove the foam support so that the flat tire will fit in the storage area. Place the flat tire with the appearance-side face down and store the jack container in the center of the tire. See the diagram for more information. The compact spare is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can.
Notice: Wheel covers will not fit on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare. Do not try to put a wheel cover on your compact spare tire. It will note fit. Store the wheel cover in the trunk until you have the flat tire repaired or replaced.
5-92
Use the following diagram as a guide for storing the compact spare tire in the trunk:
A. Compact Spare Tire
Cover Wing Nut
B. Compact Spare Tire
Cover
C. Plastic Wing Nut D. Retainer E. Jack Container with
Wheel Wrench and Jack
F. Flat Road Tire G. Compact Spare Tire H. Foam Insert I. Bolt J. Wheel Wrench K. Jack L. Jack Container
Compact Spare Tire (CTS Only) Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have the full-size tire repaired or replaced at your convenience. Of course, it is best to replace the spare with a full-size tire as soon as possible. The spare tire will last longer and be in good shape in case it is needed again. Notice: When the compact spare is installed, do not take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle. Do not use the compact spare on other vehicles. And do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. Notice: Tire chains will not fit your compact spare. Using them can damage your vehicle and can damage the chains too. Do not use tire chains on your compact spare.
5-93
If you use abrasive cleaners when cleaning
Notice: glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the integrated radio antenna and the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles. Your GM dealer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your GM dealer to remove odors from your vehicle’s upholstery.
Appearance Care
Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth.
5-94
Do not clean your vehicle using the following cleaners or techniques: (cid:127) Never use a knife or any other sharp object to
remove a soil from any interior surface.
(cid:127) Never use a stiff brush. It can cause damage to
your vehicle’s interior surfaces.
(cid:127) Never apply heavy pressure or rub aggressively with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.
(cid:127) Use only mild, neutral-pH soaps. Avoid laundry
detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.
(cid:127) Do not heavily saturate your upholstery while
cleaning.
(cid:127) Damage to your vehicle’s interior may result from the use of many organic solvents such as naptha, alcohol, etc.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda. Before cleaning, gently remove as much of the soil as possible using one of the following techniques:
For liquids: gently blot the remaining soil with a paper towel. Allow the soil to absorb into the paper towel until no more can be removed. For solid dry soils: remove as much as possible and then vacuum.
To clean, use the following instructions: 1. Saturate a lint-free, clean white cloth with water or
club soda.
2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled. 4. Continue to gently rub the soiled area until the
cleaning cloth remains clean.
5. If the soil is not completely removed, use a mild
soap solution and repeat the cleaning process that was used with plain water.
5-95
(cid:127) (cid:127) If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet.
Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on your leather.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on your instrument panel. The increase in gloss may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.
Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth.
5-96
Speaker Covers Vacuum around a speaker cover gently, so that the speaker will not be damaged. Clean spots with just water and mild soap.
Care of Safety Belts Keep belts clean and dry.
{CAUTION:
Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 6-13.
Washing Your Vehicle The paint finish on the vehicle provides beauty, depth of color, gloss retention, and durability. The best way to preserve the vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash the vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-101. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-97.
5-97
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/Appearance Materials on page 5-101. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. The vehicle has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather, and chemical fallout that can take their toll over a period of years. To help keep the paint finish looking new, keep the vehicle in a garage or covered whenever possible.
5-98
Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap, or other material may be on the blade or windshield. Clean the outside of the windshield with a glass cleaning liquid or powder and water solution. The windshield is clean if beads do not form when it is rinsed with water. Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn.
Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
If you use strong soaps, chemicals,
Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only GM-approved cleaners on aluminum or chrome-plated wheels. The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application.
If you drive your vehicle through an
Notice: automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes. Do not take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
5-99
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your GM dealer. Larger areas of finish damage can be corrected in your GM dealer’s body and paint shop.
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.
5-100
Vehicle Care/Appearance Materials
Description
Usage
Description
Polishing Cloth Wax-Treated Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner Vinyl Cleaner
Glass Cleaner
Chrome and Wire Wheel Cleaner
Finish Enhancer
Usage
Interior and exterior polishing cloth. Removes tar, road oil, and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls. Cleans vinyl. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels and wire wheel covers. Removes dust, fingerprints, and surface contaminants. Spray on and wipe off.
Swirl Remover Polish
Cleaner Wax
Foaming Tire Shine Low Gloss
Wash Wax Concentrate
Spot Lifter
Odor Eliminator
Removes swirl marks, fine scratches, and other light surface contamination. Removes light scratches and protects finish. Cleans, shines, and protects in one step. No wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly removes spots and stains from carpets, vinyl, and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.
5-101
Vehicle Identification
Vehicle Identification Number (VIN)
This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration.
Engine Identification The eighth character in the VIN is the engine code. This code will help you identify your vehicle’s engine, specifications, and replacement parts.
Service Parts Identification Label You will find this label in the trunk. It is very helpful if you ever need to order parts. On this label, you will find the following: (cid:127) VIN (cid:127) Model designation (cid:127) Paint information (cid:127) Production options and special equipment Be sure that this label is not removed from the vehicle.
5-102
Electrical System
Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-64.
Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker. If the wiper motor overheats due to heavy snow, the wipers will stop until the motor cools and will then restart.
Power Windows and Other Power Options Circuit breakers protect the power windows and power seats. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating. If a fuse blows, see your dealer for service immediately. If you ever have a problem on the road and don’t have a spare fuse, you can “borrow” one that has the same amperage. Pick some feature of your vehicle that you can get along without – like the radio or cigarette lighter – and use its fuse, if it is the correct amperage. Replace it as soon as you can. The fuses are located in three fuse blocks, one located in the engine compartment on the passenger’s side and the other two under the rear seat.
5-103
Underhood Fuse Block
The underhood fuse block is located in the engine
compartment on the passenger’s side of the vehicle.
See Engine Compartment Overview on page 5-12
for more information on location.
To access the fuses, push in the two tabs located on
each side of the fuse block cover. Then lift the cover off.
5-104
Relays
LO SPEED FAN RELAY
MINI
Usage
Low Speed Fan Motor
HI SPEED FAN RELAY MINI High Speed Fan Motor ACCESSORY RELAY MINI
Wipe-Wash, PRNDL, Accessory Power Outlets
S/P FAN
Series/Parallel Fan
RELAY MINI PARK LAMP RELAY MICRO Parking Lamps HORN RELAY
Horn
MICRO
Relays HI BEAM
Usage RELAY MICRO High-Beam Headlamps DRL RELAY MICRO-OPT Daytime Running Lamps LO BEAM RELAY/HID MINI-OPT
Low-Beam HID Headlamps
HDLP WASH
RELAY
MINI-OPT SPARE BLOWER
Headlamp Washer Motor
Not Used
Front Blower
RELAY MINI FOG LAMP RELAY MICRO Fog Lamps MAIN RELAY
Powertrain/ECM
MICRO
CMP CLU
Starter Solenoid
STARTER RELAY MINI RELAY MICRO Compressor Clutch IGN-1 RELAY Ignition Switch (ON)
MICRO
Wiring
Usage
Harnesses BODY W/H Wiring Harness Connection BODY W/H Wiring Harness Connection ENG W/H
Engine Wiring Harness Connection
J Cases
R REAR
R REAR
L REAR
L REAR
HI FAN LO FAN BLOWER STARTER
ABS
Usage
RRPDB (Passenger’s Side Rear Power Distribution Box) RRPDB (Passenger’s Side Rear Power Distribution Box) LRPDB (Driver’s Side Rear Power Distribution Box) LRPDB (Driver’s Side Rear Power Distribution Box) High Cooling Fan Motor Low Cooling Fan Motor PWM Fan Motor Assembly Starter Solenoid Anti-Lock Brake System
5-105
Fuses
RT PARK
HORN
Usage
Passenger’s Side Taillamp Assembly, Front Sidemarker and Front Parking Lamp Assembly Dual Horn Assembly
LT HI BEAM Driver’s Side High-Beam Headlamp LT LOW BEAM Driver’s Side Low-Beam Headlamp RT LOW BEAM Passenger’s Side Low-Beam RT HI BEAM Passenger’s Side High-Beam
Headlamp
Headlamp Manual Transmission Output Speed Sensor Not Used ECM (Engine Control Module), TCM (Transmission Control Module), PASS-Key® III+ Module Driver’s Side Taillamp Assembly, Front Sidemarker and Front Parking Lamp Assembly Rear License Plate Assembly, Dash Integrated Module (DIM) DIM, ALDL (Assembly Line Data Link) Turn Signal/Hazard Flasher Module Electronic Control Module
TOS
SPARE
THEFT
LT PARK
DIMMING
DIM/ALDL
FLASHER
ECM
5-106
Fuses
STRG CTLS
HTR VLV/
CLTCH
WASH NOZ
PRE O2/CAM
TCM/IPC
SPARE
Usage
Steering Wheel Control Pad, Headlamp Switch Clutch Switch (Normal Closed), Clutch Switch (Normal Open), Jumper to Start Relay Coil for Automatic Transmission Driver’s and Passenger’s Side Heated Washer Nozzles Driver’s & Passenger’s Side Oxygen Sensors, CAM Phaser, Canister Purge Transmission Control Module, Engine Control Module, Instrument Panel Cluster Not Used
IGN MOD/MAF Front Bank Ignition Modules, ELEC PRNDL Electronic PRNDL (Export)
Mass Airflow Sensor
SPARE SPARE
IGN SW
Not Used
Not Used
Ignition Switch (Power to IGN-3
and CRANK)
VOLT CHECK DIM (Dash Integration Module)
ECM/TCM
TCM (Transmission Control Module), ECM (Engine Control Module), IPC (Instrument Panel Cluster), PASS-Key® III+ Module
Fuses
Usage
WPR MOD Windshield Wiper Module Assembly
ODD
Odd Ignition Coils, Fuel Injectors, Odd Injection Coils COMP CLUTCH Compressor Clutch
INJ/COILS
WPR SW FOG LAMP
OUTLET
POST 02
I/P OUTLET
Windshield Wiper/Washer Switch Fog Lamps Center Console Accessory Power Outlet Driver’s and Passenger’s Side Oxygen Sensors, LRPDB (Pusher Cooling Fan Relay) Instrument Panel Accessory Power Outlet
Fuses CCP EVEN
INJ/COILS
SPARE SPARE SPARE
Circuit Breakers
HDLP WASH
C/B-OPT
Usage
Climate Control
Even Injection Coils
Not Used Not Used Not Used
Usage
Headlamp Washer Motor
5-107
Rear Underseat Fuse Block To access the rear underseat fuse blocks, you will have to first remove the rear seat cushion. Removing the Rear Seat Cushion If, when removing or reinstalling the rear Notice: seat, you do not do it carefully, you could damage the fuse center. Avoid contact between the rear seat and the fuse center whenever you remove or reinstall the rear seat. To remove the rear seat cushion, do the following: 1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of
the vehicle.
3. Slide the cushion out one of the rear doors and set
it aside.
5-108
Rear Pass-Through Seat
CAUTION:
(Continued)
seat cushion at all, it will not be there to work for the next passenger. The person sitting in that position could be badly injured. After reinstalling the seat cushion, always check to be sure that the safety belts are properly routed and are not twisted.
To reinstall the rear seat cushion, do the following: 1. Position the seat cushion so that you can route the safety belts through the proper slots in the seat cushion.
2. Slide the rear of the cushion up and under the seatback so the rear-locating guides hook into the wire loops on the back frame.
3. With the seat cushion lowered, push rearward and then press down on the seat cushion until the seat cushion snaps into place.
4. Push and pull on the seat cushion to make sure it
is locked into place.
5. Check to make sure the safety belts are properly
routed and that no portion of any safety belt is trapped under the seat cushion.
5-109
Split-Folding Rear Seat
{CAUTION:
A safety belt that is not properly routed through the seat cushion or is twisted will not provide the protection needed in a crash. If the safety belt has not been routed through the
CAUTION:
(Continued)
Rear Underseat Fuse Block (Driver’s Side)
The driver’s side rear fuse block is located under the rear seat on the driver’s side of the vehicle. The rear seat cushion must be removed to access the rear fuse block. See “Removing the Rear Seat Cushion” listed previously. To access the fuse block, push in the two tabs located at each end of the fuse block cover. Then lift the cover off.
5-110
Fuses SPARE SPARE AUDIO SPARE
Usage
Not Used Not Used Radio, OnStar Module Not Used
REAR DR MOD Rear Door Modules
SPARE DRIVER DR MOD
BAS
HDLP
LEVELING
SPARE
CCP
IGN 3
SPARE SPARE
Not Used
Driver’s Door Module
Taillamps, Center High-Mounted Stoplamp, Flasher Module, ABS Module, Trailer Lamps Headlamp Leveling System Chassis Sensors (Export Only) Not Used CCP (Climate Control Panel) Heated Seat Modules, Air Inlet Motor, Shifter Assembly Not Used Not Used
FUSE PULLER Fuse Puller
L FRT HTD SEAT MOD MEM/ADAPT
SEAT
Driver’s Heated Seat Module
Driver’s Power Seat Switch, Memory Seat Module
Fuses TRUNK
Usage DR RELEASE Trunk Release Motor REVERSE
ISRVM (Inside Rearview Mirror), License Plate Lamp Assembly Not Used Taillamp Assemblies, Front Position Lamp Assemblies
LAMP SPARE
POSITION
LAMP
J Cases
AMP
Usage
Audio Amplifier
PUSHER FAN Pusher Fan (Export Only)
Relays
BAS RELAY
MINI
Usage
Brake Apply Sensor
PUSHER FAN Pusher Fan (Export Only) L POSITION RELAY MICRO Driver’s Side Position Lamp TRK DR REL SOL RELAY
Trunk Release Motor
MICRO
Relays
Usage
REV LAMP
ISRVM (Inside Rearview Mirror), License Plate Lamp Assembly
RELAY MICRO R POSITION RELAY MICRO Passenger’s Side Position Lamp Heated Seat Modules, Air Inlet IGN 3 RELAY Motor, Shifter Assembly
MICRO
STANDING
LAMP
RLY MICRO
Control for Position Lamp Relays
Circuit Breakers
SEAT C/B
Usage
Power Seat Switches, Memory Seat Module
Misc. JOINT
CONNECTOR Joint Connector
Usage
5-111
Rear Underseat Fuse Block (Passenger’s Side)
Fuses
Usage
TRUNK DIODE Trunk Lamp
POWER
SOUNDER
SPARE
CANISTER
VENT FUEL
PUMP MTR
Power Sounder, Inclination Sensor
Not Used
Canister Vent Solenoid
Fuel Pump Motor
The passenger’s side rear fuse block is located under the rear seat on the passenger’s side of the vehicle. The rear seat cushion must be removed to access the rear fuse block. See “Removing the Rear Seat Cushion” listed previously. To access the fuse block, push in the two tabs located at each end of the fuse block cover. Then lift the cover off.
SPARE
R FRT HTD SEAT MOD
SPARE AIR BAG
RIM
ABS
SPARE SPARE SPARE
Not Used Passenger’s Side Heated Seat Module Not Used SDM (Sensing Diagnostic Module) ISRVM (Inside Rearview Mirror), Power Sounder, RIM Anti-Lock Brake System Not Used Not Used Not Used
FUSE PULLER Fuse Puller
LAMP
INTERIOR
Hush Panel Lamps, Puddle Lamps, Overhead Courtesy Lamp Assembly PSGR DR MOD Right Front Passenger Door Module RIM/IGN SW RIM (Rear Integration Module),
Ignition Switch, Key Lock Cylinder
5-112
Usage
Relays
Usage
Fuses
REAR FOG
LAMP SPARE
TV/VICS
Rear Fog Lamps (Export Only)
Not Used TV Tuner Assembly (Export Only), VICS (Vehicle Information Communication System) Module
J Cases
Usage
REAR DEFOG Rear Window Defogger Element
SUNROOF MOD Power Sunroof Module
Relays SPARE
Not Used
Usage
REAR DEFOG RELAY MINI Rear Window Defogger
SPARE
Not Used
REAR FOG
LAMP
RLY MICRO
FUEL PUMP
MOTOR
RLY MICRO INT LAMP
RELAY MICRO IGN 1 RELAY
MICRO SPARE
Fuel Pump Motor
Hush Panel Lamps, Puddle Lamps, Overhead Courtesy Lamp Assembly
Ignition Switch
Not Used
Circuit Breakers DR MOD PWR C/B
Door Modules
Misc. JOINT
CONNECTOR Joint Connector
Usage
Usage
Rear Fog Lamps (Export Only)
5-113
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-13 for more information.
Application
Cooling System
2.8L HFV6
3.6L HFV6
6.0L V8
Engine Oil with Filter
2.8L HFV6
3.6L HFV6
6.0L V8
Fuel Tank
Transmission
Automatic 6-Speed Manual – CTS 6-Speed Manual – CTS-V
5-114
Capacities
English
11.7 qt 12.1 qt 13.4 qt
6.0 qt 6.0 qt 6.0 qt 17.5 gal
9.5 qt 1.9 qt 3.7 qt 100 lb ft
Metric
11.1 L 11.8 L 12.7 L
5.7 L 5.7 L 5.7 L 66.2 L
9.0 L 1.8 L 3.5 L
(140 Y) Wheel Nut Torque All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Recheck fluid level after filling.
Engine
2.8L HFV6
3.6L HFV6
6.0L V8
Engine Specifications
VIN Code
Transmission
Automatic
6-Speed Manual
Automatic
6-Speed Manual 6-Speed Manual
Spark Plug Gap
0.043 inches (1.1 mm)
0.043 inches (1.1 mm)
0.040 inches (1.01 mm)
CTS-V Engine Data
Engine
6.0L V8 (LS2)
Horsepower
400 hp (298 kW)
@ 6000 rpm
Torque
Displacement
Compression Ratio
400 ft lb (542 Nm)
@ 4400 rpm
6.0 L
10.9:1
5-115
✍ NOTES
5-116
Section 6
Maintenance Schedule
Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
Using the Maintenance Schedule ......................6-3
Scheduled Maintenance ...................................6-4
Additional Required Services ............................6-6
Maintenance Footnotes ...................................6-8
Owner Checks and Services ............................6-9
At Each Fuel Fill
..........................................6-10
At Least Once a Month .................................6-10
At Least Once a Year ...................................6-11
Recommended Fluids and Lubricants ...............6-13
Normal Maintenance Replacement Parts ..........6-15
Engine Drive Belt Routing (CTS-V) ..................6-16
Maintenance Record .....................................6-16
6-1
Maintenance Schedule
Introduction Important: Keep engine oil at the proper level and change as recommended.
Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.
Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.
Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.
6-2
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your GM Goodwrench® dealer. This schedule is for vehicles that:
carry passengers and cargo within recommended limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-32. are driven on reasonable road surfaces within legal driving limits. use the recommended fuel. See Gasoline Octane on page 5-5.
The services in Scheduled Maintenance on page 6-4
should be performed when indicated. See Additional
Required Services on page 6-6 and Maintenance
Footnotes on page 6-8 for further information.
{CAUTION:
Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your GM Goodwrench® dealer to have a qualified technician do the work.
Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your GM Goodwrench® dealer do these jobs. When you go to your GM Goodwrench® dealer for your service needs, you will know that GM-trained and supported service technicians will perform the work using genuine GM parts.
6-3
(cid:127) (cid:127) (cid:127) If you want to purchase service information, see Service Publications Ordering Information on page 7-15. Owner Checks and Services on page 6-9 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-13 and Normal Maintenance Replacement Parts on page 6-15. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine GM parts.
Scheduled Maintenance When the Change Engine Oil message in the Driver Information Center (DIC) comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. Your GM Goodwrench® dealer has GM-trained service technicians who will perform this work using genuine GM parts and reset the system.
6-4
If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-22 for information on the Engine Oil Life System and resetting the system. When the Change Engine Oil message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II, and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I — Use Maintenance I if the change engine oil message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.
Scheduled Maintenance
Service
Maintenance I Maintenance II
Change engine oil and filter. See Engine Oil on page 5-16. Reset oil life system. See Engine Oil Life System on page 5-22. An Emission Control Service. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 5-23. See footnote (n). Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 5-72 and “Tire Wear Inspection” in At Least Once a Month on page 6-10. Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed. Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Replace passenger compartment air filter. See footnote (g).
•
•
•
•
•
•
•
•
•
•
•
•
•
• • • • • •
6-5
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.
Service and Miles (Kilometers)
Additional Required Services
75,000
25,000
(41 500)
50,000
(83 000)
(125 000)
100,000
(166 000)
125,000
(207 500)
150,000
(240 000)
Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-23. Change automatic transmission fluid and filter (severe service only). See footnote (h). CTS-V Only: Change 6-speed manual transmission fluid (severe service only). See footnotes (l) and (m). CTS-V Only: Change hydraulic clutch fluid (severe service only). See footnote (l).
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
6-6
Additional Required Services (cont’d)
Service and Miles (Kilometers)
CTS-V Only: Change rear axle fluid (severe service only). See footnotes (l) and (m). CTS-V Only: Change brake fluid (severe service only). See footnote (l). Replace spark plugs. An Emission Control Service. Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (p).
25,000
(41 500)
50,000
(83 000)
75,000
(125 000)
100,000
(166 000)
125,000
(207 500)
150,000
(240 000)
•
•
•
•
•
•
•
•
•
•
•
•
6-7
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year. (d) Visually inspect wiper blades for wear or cracking. Replace wiper blades that appear worn or damaged or that streak or miss areas of the windshield.
(e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken airbag coverings, and have them repaired or replaced. The airbag system does not need regular maintenance. (f) Lubricate all key lock cylinders. Lubricate all body door hinges. Lubricate all hinges and latches, including those for the hood, rear compartment, console door, and any folding seat hardware. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. (g) If you drive regularly under dusty conditions, the filter may require replacement more often.
6-8
(h) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:
− In heavy city traffic where the outside temperature
regularly reaches 90°F (32°C) or higher.
− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as high performance operation. If you do not use your vehicle under any of these conditions, the fluid and filter do not require changing. (i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer perform this service. See Engine Coolant on page 5-28 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck. Pressure test the cooling system and pressure cap. (k) A fluid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the fluid level checked. Add fluid if needed. (l) Change fluid if the vehicle is used for high performance operation.
(m) Change fluid whenever the vehicle has been driven for 3,000 miles (5 000 km) with the transmission temperature at 290°F (143°C) or higher without using an auxiliary fluid cooler. See Message Center (CTS-V) on page 3-47 and Transmission Fluid Hot Message on page 3-50. (n) If you drive regularly under dusty conditions, inspect the filter at each engine oil change. (p) Visually inspect belt for fraying, excessive cracks, or obvious damage. Replace belt if necessary.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench® dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-13.
6-9
At Least Once a Month Tire Inflation Check Visually inspect your vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Tires on page 5-58 for further details. Check to make sure the spare tire is stored securely. See Changing a Flat Tire (CTS Only) on page 5-84. Tire Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification. Check the tires for wear and, if necessary, rotate the tires. See Tire Inspection and Rotation on page 5-72.
It is important to check your oil regularly
At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-16 for further details. Notice: and keep it at the proper level. Failure to keep your engine oil at the proper level can cause damage to your engine not covered by your warranty. Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 5-28 for further details. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.
6-10
At Least Once a Year Starter Switch Check
{CAUTION:
Automatic Transmission Shift Lock Control System Check
{CAUTION:
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before you start, be sure you have enough room
around the vehicle.
2. Firmly apply both the parking brake and the regular
brake. See Parking Brake on page 2-33. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.
3. On automatic transmission vehicles, try to start
the engine in each gear. The vehicle should start only in PARK (P) or NEUTRAL (N). If the vehicle starts in any other position, contact your GM Goodwrench® dealer for service. On manual transmission vehicles, put the shift lever in NEUTRAL (N), push the clutch pedal down halfway, and try to start the engine. The vehicle should start only when the clutch pedal is pushed down all the way to the floor. If the vehicle starts when the clutch is not pushed all the way down, contact your GM Goodwrench® dealer for service.
1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
2. Firmly apply the parking brake. See Parking Brake
on page 2-33. Be ready to apply the regular brake immediately if the vehicle begins to move.
3. With the engine off, turn the ignition to ON, but do not start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), contact your GM Goodwrench® dealer for service.
6-11
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.
To check the parking brake’s holding ability: With the engine running and transaxle in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. To check the PARK (P) mechanism’s holding ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.
Contact your GM Goodwrench® dealer if service is required. Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to OFF in each shift lever position. (cid:127) With an automatic transmission, the ignition should turn to OFF only when the shift lever is in PARK (P). The key should come out only in OFF.
(cid:127) With a manual transmission, the ignition should turn to OFF only when the key release button is pressed. The key should come out only in OFF.
Contact your GM Goodwrench® dealer if service is required. Parking Brake and Automatic Transmission Park (P) Mechanism Check
{CAUTION:
When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
6-12
(cid:127) (cid:127) Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification may be obtained from your dealer. Usage
Fluid/Lubricant
Engine Oil (V6 Engine)
Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. GM Goodwrench® oil meets all the requirements for your vehicle. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-16.
Usage
Fluid/Lubricant
The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard may be identified as synthetic, and should also be identified with the American Petroleum Institute Certified for Gasoline Engines starburst symbol. However, not all synthetic API oils with the starburst symbol will meet this GM standard. You should look for and use only an oil that meets GM Standard GM4718M. GM Goodwrench® oil meets all the requirements for your vehicle. For the proper viscosity, see Engine Oil on page 5-16. 50/50 mixture of clean, drinkable water and use only DEX-COOL® Coolant. See Engine Coolant on page 5-28. Delco® Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.
GM Optikleen® Washer Solvent.
Hydraulic Clutch Fluid. Use only
GM Part No. U.S. 88958860, in
Canada 88901244, Super DOT-4
brake fluid.
Engine Oil (V8 Engine)
Engine Coolant
Hydraulic Brake
System
Windshield
Washer
Hydraulic
Clutch System
6-13
Usage
Fluid/Lubricant
Usage
Fluid/Lubricant
Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. GM Power Steering Fluid (GM Part No. U.S. 89021184, in Canada 89021186). SAE 75W-90 Gear Oil (GM Part No. U.S. 89021806, in Canada 89021807). DEXRON®-III Automatic Transmission Fluid. Look for “Approved for the H-Specification” on the label. DEXRON®-III Automatic Transmission Fluid. Look for “Approved for the H-Specification” on the label. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.
Parking Brake Cable Guides
Power Steering
System
Manual
Transmission
(CTS)
Manual
Transmission
(CTS-V)
Automatic
Transmission
Key Lock Cylinders
Floor Shift Linkage
6-14
Rear Axle
Rear Axle (Limited-Slip Differential)
Hood Latch Assembly, Secondary
Latch, Pivots, Spring Anchor,
and
Release Pawl
SAE 75W-90 Synthetic Axle
Lubricant (GM Part No. U.S.
12378261, in Canada 10953455)
meeting GM Specification 9986115.
SAE 75W-90 Synthetic Axle
Lubricant (GM Part No. U.S.
12378261, in Canada 10953455)
meeting GM Specification 9986115.
With a complete drain and refill add
4 ounces (118 ml) of Limited-Slip
Axle Lubricant Additive (GM Part
No. U.S. 1052358, in Canada
992694) where required. See Rear
Axle on page 5-49
Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.
Hood and Door
Hinges
Weatherstrip Conditioning
Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Dielectric Silicone Grease (GM Part No. U.S. 12345579, in Canada 992887).
Normal Maintenance Replacement Parts Replacement parts identified below by name, part number or specification can be obtained from your dealer.
Part
GM Part Numbers
Engine Air Cleaner/Filter Engine Oil Filter
2.8L V6 and 3.6L V6
6.0L V8
Passenger Compartment Air Filter Element Spark Plugs
2.8 L HFV6
3.6 L HFV6
6.0 L V8
Wiper Blades (Hook Type)
Driver’s Side – 22 inches (56.5 cm) Passenger’s Side – 21 inches (53.3 cm)
25728874
25177917
88984215
25740404
12565996
12597464
12571164
12487636
12487638
ACDelco® Part
Numbers A2029C
PF2129
PF46
CF133
41-988
41-990
41-985
— —
6-15
Engine Drive Belt Routing (CTS-V) 6.0L V8 Engine
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages. You should retain all maintenance receipts.
6-16
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record
6-17
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record (cont’d)
6-18