Login- Download PDF Manual
-
will automatically determine when a GPS signal is restored and provide a heading again. See Compass Messages on page 5‑34 for the messages that may be displayed for the compass.
Clock (Base Radio)
Setting the Time To set the time: 1. Select Settings from the Home
Page and select Set Time.
2. Turn the MENU knob to increase
or decrease the hour.
3. Press the MENU knob to go to the next option. Press S BACK to go to the last menu and save the changes.
AUTO SET In the Set Time view, push on the area just above the chrome bar and below the "AUTO SET" screen button to turn on/off the Auto Time adjust capability.
Clock (Uplevel Radio) The infotainment system controls are used to access the time and date settings through the menu system. See “Home Page” in the infotainment manual for information about how to use the menu system.
Setting the Time To set the time: 1. From the Home Page, press the
SETTINGS screen button and press Time and Date.
2. Press Set Time and press + or − to increase or decrease hours, minutes, and AM or PM. Press 12Hr or 24Hr for 12 or 24 hour clock.
3. Press } to go back to the
previous menu.
To set the date: 1. Press the SETTINGS screen
button and press Time and Date. 2. Press Set Date and press + or −
to increase or decrease month, day, or year.
3. Press } to go back to the
previous menu.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (7,1)
Instruments and Controls
5-7
Certain accessory power plugs may not be compatible with the accessory power outlet and could overload vehicle or adapter fuses. If a problem is experienced, see your dealer. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. See Add-On Electrical Equipment on page 9‑75.
Notice: Hanging heavy equipment from the power outlet can cause damage not covered by the vehicle warranty. The power outlets are designed for accessory power plugs only, such as cell phone charge cords. Always unplug electrical equipment when not in use and do not plug in equipment that exceeds the maximum 20 amps rating.
Power Outlets The accessory power outlets can be used to plug in electrical equipment, such as a cell phone or MP3 player. The vehicle has two accessory power outlets:
Inside the front storage bin below the climate control system.
. On the rear of the center floor
console.
Lift the cover to access the accessory power outlet.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (8,1)
5-8
Instruments and Controls
Warning Lights, Gauges, and Indicators Warning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury.
Warning lights come on when there could be a problem with a vehicle function. Some warning lights come on briefly when the engine is started to indicate they are working. Gauges can indicate when there could be a problem with a vehicle function. Often gauges and warning lights work together to indicate a problem with the vehicle.
When one of the warning lights comes on and stays on while driving, or when one of the gauges shows there may be a problem, check the section that explains what to do. Follow this manual's advice. Waiting to do repairs can be costly and even dangerous.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (9,1)
Instrument Cluster
Instruments and Controls
5-9
English Shown, Metric Similar
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (10,1)
5-10
Instruments and Controls
Cluster Application Displays The cluster has three interactive display zones. Use the five-way control on the right steering wheel control to move between the different display zones and scroll through the different displays. The left and right zones display Driver Information Center (DIC) information. See Driver Information Center (DIC) on page 5‑26. The center zone displays application information for navigation, audio, phone, or settings.
Navigation If there is no active route, a compass will be displayed. If there is an active route, press SEL to end route guidance or turn the voice prompts on or off.
Audio While the Audio application page is displayed, press SEL to enter the Audio menu. In the Audio menu search for music or change the audio source.
Phone While the Phone application page is displayed, press SEL to enter the Phone menu. In the Phone menu, if there is no active phone call, view recent calls or scroll through contacts. If there is an active call, mute the phone or switch to handset operation.
Settings Press SEL while the Settings application page is displayed to enter the Settings menu.
Units: Press SEL while Units is highlighted to enter the Units menu. Choose English or metric units by pressing SEL while the desired item is highlighted. A checkmark will be displayed next to the selected item. Info Pages: Press SEL while Info Pages is highlighted to select the items to be displayed in the DIC information displays. See Driver Information Center (DIC) on page 5‑26. Open Source Software: Press SEL while Open Source Software is highlighted to display open source software information.
Speedometer The speedometer shows the vehicle's speed in either kilometers per hour (km/h) or miles per hour (mph).
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (11,1)
Instruments and Controls
5-11
Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. This vehicle has a tamper-resistant odometer. If the vehicle needs a new cluster installed, the new odometer is set to the mileage of the old odometer. If this is not possible, it is set at zero and a label is put on the driver door to show the old mileage reading.
Trip Odometer The trip odometer can show how far the vehicle has been driven since the trip odometer was last reset.
The trip odometer is accessed and reset through the Driver Information Center (DIC). See Driver Information Center (DIC) on page 5‑26.
Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). Notice: If the engine is operated with the tachometer in the shaded warning area, the vehicle could be damaged, and the damages would not be covered by the vehicle warranty. Do not operate the engine with the tachometer in the shaded warning area.
Fuel Gauge
When the ignition is on, the fuel gauge indicates about how much fuel is left in the tank. There is an arrow near the fuel gauge pointing to the side of the vehicle the fuel door is on. When the indicator nears empty, the low fuel light comes on. There still is a little fuel left, but the vehicle should be refueled soon.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (12,1)
5-12
Instruments and Controls
Here are four things that some owners ask about. None of these show a problem with the fuel gauge: . At the service station, the
fuel pump shuts off before the gauge reads full. It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. The gauge moves a little while turning a corner or speeding up. The gauge takes a few seconds to stabilize after the ignition is turned on, and goes back to empty when the ignition is turned off.
Engine Coolant Temperature Gauge
Metric
English
This gauge measures the temperature of the vehicle's engine. While driving under normal operating conditions, if the needle moves into the shaded area, the engine is too hot. Pull off the road, stop the vehicle, and turn off the engine as soon as possible.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (13,1)
Instruments and Controls
5-13
Safety Belt Reminders
Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument cluster.
If the driver safety belt is buckled, neither the chime nor the light comes on. Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System on page 3‑27.
When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving.
When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled.
This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on. The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the warning light and/or chime, remove the object from the seat or buckle the safety belt.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (14,1)
5-14
Instruments and Controls
Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3‑19.
The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.
{ WARNING
If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.
If there is a problem with the airbag system, a Driver Information Center (DIC) message may also come on. See Airbag System Messages on page 5‑41.
Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3‑27 for important safety information. The passenger airbag status indicator is in the overhead console.
United States
Canada and Mexico
When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off for several seconds
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (15,1)
as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or the on or off symbol to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the front outboard passenger frontal airbag and knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.
Instruments and Controls
5-15
{ WARNING
If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5‑14 for more information, including important safety information.
Charging System Light
a check to show the light is working. It should go out when the engine is started. If the light stays on, or comes on while driving, there may be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. When this light comes on, or is flashing, the Driver Information Center (DIC) also displays a message. See Battery Voltage and Charging Messages on page 5‑33. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.
The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (16,1)
5-16
Instruments and Controls
Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in Service Only Mode, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions on page 9‑16.
If the malfunction indicator lamp comes on while the engine is running, this indicates that the
OBD II system has detected a problem and diagnosis and service might be required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system also assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty. Notice: Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can
affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/ Maintenance test. See Accessories and Modifications on page 10‑3. This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (17,1)
Instruments and Controls
5-17
If towing a trailer, reduce the amount of cargo being hauled as soon as it is possible.
If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. The following may correct an emission control system malfunction: . Check that the fuel cap is fully
installed. See Filling the Tank on page 9‑68. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere.
A few driving trips with the cap properly installed should turn the light off.
. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up. If one or more of these conditions occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9‑64. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and
diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).
The DLC is under the instrument panel to the left of the steering wheel. See your dealer if assistance is needed.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (18,1)
5-18
Instruments and Controls
The vehicle may not pass inspection if:
The malfunction indicator lamp is on with the engine running, or if the vehicle is placed in Service Only Mode and the malfunction indicator lamp does not come on. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp. The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed. The vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II
system readiness, your dealer can prepare the vehicle for inspection.
Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. If the warning light comes on, there is a brake problem. Have the brake system inspected right away.
Metric
English
This light comes on briefly when the vehicle is turned on. If it does not come on then, have it fixed so it will be ready to warn if there is a problem. If the light comes on and stays on, there is a base brake problem.
{ WARNING
The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (19,1)
Instruments and Controls
5-19
Parking Brake Light
Service Electric Parking Brake Light
Metric
English
This light comes on when the parking brake is applied. If the light continues flashing after the parking brake is released, or while driving, there is a problem with the electric parking brake system or another system. A message may also display in the Driver Information Center (DIC). See Brake System Messages on page 5‑33. If the light does not come on, or remains flashing, see your dealer.
This light should come on briefly when the vehicle is in ON/RUN. If it does not come on, have it fixed so it will be ready to warn if there is a problem.
If this light stays on, there is a problem with the electric parking brake system or another system on the vehicle that is causing the parking brake system to work at a reduced level. The vehicle can still be driven, but should be taken to a dealer as soon as possible. See the information for the electric parking brake under Parking Brake (Electric) on page 9‑30 or Parking Brake (Manual) on page 9‑33. If a message displays in the Driver Information Center (DIC), see Brake System Messages on page 5‑33.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (20,1)
5-20
Instruments and Controls
Antilock Brake System (ABS) Warning Light
This light comes on briefly when the engine is started. If the light does not come on, have it fixed so it will be ready to warn if there is a problem. If the ABS light stays on, turn the ignition off. If the light comes on while driving, stop as soon as it is safely possible and turn off the vehicle. Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. A chime may also sound when the light comes on steady.
If the ABS light is the only light on, the vehicle has regular brakes, but the antilock brakes are not functioning. If both the ABS and the brake system warning light are on, the vehicle's antilock brakes are not functioning and there is a problem with the regular brakes. See your dealer for service. See Brake System Warning Light on page 5‑18 and Brake System Messages on page 5‑33.
Lane Departure Warning (LDW) Light
If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. This light comes on green when the system is on and ready to operate. When the system determines that the vehicle is leaving its lane without using the turn signal, this light will change to amber and flash. See Lane Departure Warning (LDW) on page 9‑62.
Vehicle Ahead Indicator
If available, this light briefly comes on amber while starting the vehicle.
If available, this light in the Driver Information Center (DIC) displays green when a vehicle is detected ahead.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (21,1)
This light will display amber when you are following a vehicle ahead much too closely. See Forward Collision Alert (FCA) System on page 9‑55.
Traction Off Light
This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button.
Instruments and Controls
5-21
This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control System (TCS) on page 9‑34 and StabiliTrak® System on page 9‑36.
StabiliTrak® OFF Light
If the TCS is off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control System (TCS) on page 9‑34 and StabiliTrak® System on page 9‑36.
Traction Control System (TCS)/StabiliTrak® Light
This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off.
The StabiliTrak or Traction Control System (TCS) indicator/warning light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (22,1)
5-22
Instruments and Controls
If the light is on and not flashing, the TCS, and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service. If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See StabiliTrak® System on page 9‑36 and Traction Control System (TCS) on page 9‑34.
Engine Coolant Temperature Warning Light
The engine coolant temperature warning light comes on when the engine has overheated. If this happens, pull over and turn off the engine as soon as possible. See Engine Overheating on page 10‑22.
Tire Pressure Light
This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer. If the system is working normally the indicator light goes off. Notice: The engine coolant temperature warning light indicates that the vehicle has overheated. Driving with this light on can damage the engine and it may not be covered by the vehicle warranty. See Engine Overheating on page 10‑22.
For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (23,1)
Instruments and Controls
5-23
When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated. A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5‑42. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10‑50.
When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10‑53.
low can also damage the
Engine Oil Pressure Light Notice: Lack of proper engine oil maintenance can damage the engine. Driving with the engine oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.
The oil pressure light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer.
If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and might have some other system problem. See your dealer.
Low Fuel Warning Light
This light is near the fuel gauge and comes on briefly when the ignition is turned on as a check to show it is working. It also comes on when the fuel tank is low on fuel. The light turns off when fuel is added. If it does not, have the vehicle serviced.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (24,1)
5-24
Instruments and Controls
Security Light
High-Beam On Light
Adaptive Forward Lighting (AFL) Light
The immobilizer light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation on page 2‑18.
This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6‑4. Automatic High-Beam Light
This light should come on briefly as the vehicle is started. If it does not come on, have the vehicle serviced by your dealer. This light comes on solid when there is a problem with the AFL system. It flashes when the system is switching between lighting modes. See Adaptive Forward Lighting (AFL) on page 6‑5.
This light comes on when the automatic high-beam headlamps are in use. See Exterior Lamp Controls on page 6‑1.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (25,1)
Lamps On Reminder
Cruise Control Light
Adaptive Cruise Control Light
Instruments and Controls
5-25
This light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6‑1.
The cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. See Cruise Control on page 9‑39.
This light in the Driver Information Center (DIC) comes on when the Adaptive Cruise Control (if equipped) is active. See Adaptive Cruise Control on page 9‑42.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (26,1)
5-26
Instruments and Controls
Information Displays
Driver Information Center (DIC) The DIC displays are shown in the left and right interactive display zones on the instrument cluster. The displays show the status of many vehicle systems. The controls for the DIC are on the right steering wheel control.
y or z : Press to move up or down in a list.
S or T : Press to move between the interactive display zones in the cluster. Press S to go back to the previous menu. SEL (Select): Press to open a menu or select a menu item. Press and hold to reset values on certain screens. DIC Information Display Options The information displays on the DIC can be turned on or off through the Settings menu. 1. Press SEL while viewing the
Settings page in the center display zone on the cluster.
2. Scroll to Info Pages and
press SEL.
3. Press y or z to move through
the list of possible information displays.
4. Press SEL while an item is
highlighted to select or deselect that item. When an item is selected, a checkmark will appear next to it.
DIC Information Displays The following is the list of all possible DIC information displays. Some of the information displays may not be available for your particular vehicle. Speed: The digital speedometer shows the vehicle speed in either kilometers per hour (km/h) or miles per hour (mph). Trip 1 and Trip 2: The Trip display shows the current distance traveled, in either kilometers (km) or miles (mi), since the trip odometer was last reset. The trip odometer can be reset by pressing and holding SEL while this display is active.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (27,1)
Instruments and Controls
5-27
Fuel Range: The Fuel Range display shows the approximate distance the vehicle can be driven without refueling. LOW will be displayed when the vehicle is low on fuel. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Average Fuel Economy: The Average Fuel Economy display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The Average Fuel Economy can be reset by pressing and holding SEL while this display is active.
Instantaneous Fuel Economy: The Instantaneous Fuel Economy display shows the current fuel economy in either liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number reflects only the fuel economy that the vehicle has right now and changes frequently as driving conditions change. Average Speed: The Average Speed display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing and holding SEL while this display is active.
Timer: This display can be used as a timer. To start the timer, press SEL while this display is active. The display will show the amount of time that has passed since the timer was last reset. To stop the timer, press SEL briefly while this display is active and the timer is running. To reset the timer to zero, press and hold SEL while this display is active. Compass: The Compass display shows the direction the vehicle is driving. Turn Arrow: The Turn Arrow display shows the next maneuver when using route guidance. Travel Time: The Travel Time display shows the estimated time duration remaining for the current route. Distance to Destination: The Distance to Destination display shows the distance to the destination when using route guidance.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (28,1)
5-28
Instruments and Controls
Speed Limit: The Speed Limit display shows the current speed limit. The information for this page comes from a roadway database. Speed Warning: The Speed Warning display allows the driver to set a speed that they do not want to exceed. To set the Speed Warning, press SEL when Speed Warning is displayed. Press y or z to adjust the value. This feature can be turned off by pressing and holding SEL while viewing this page. If the selected speed limit is exceeded, a pop-up warning is displayed and a chime may sound. Cruise Set Speed: The Cruise Set Speed display shows the speed the cruise control or Adaptive Cruise Control is set to. Battery Voltage: The Battery Voltage display shows the current battery voltage.
Oil Life: The Oil Life display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5‑35. The oil should be changed as soon as possible. See Engine Oil on page 10‑11. In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule. See Maintenance Schedule on page 11‑3. Remember, the Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Oil Life display accidentally at any time other than when the oil has just been changed.
It cannot be reset accurately until the next oil change. To reset the engine oil life system, press and hold SEL for several seconds while the Oil Life display is active. See Engine Oil Life System on page 10‑13. Tire Pressure: The Tire Pressure display shows the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or in pounds per square inch (psi). If the pressure is low, the value for that tire is shown in amber. See Tire Pressure Monitor System on page 10‑52 and Tire Pressure Monitor Operation on page 10‑53. Blank Page: The Blank Page display allows for no information to be displayed in the DIC display zone(s).
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (29,1)
Instruments and Controls
5-29
Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. The HUD information can be displayed in various languages. The speedometer reading and other numerical values can be displayed in either English or metric units. The language selection is changed through the radio and the units of measurement is changed through the instrument cluster. See Vehicle Personalization on page 5‑43 and “Settings” under Instrument Cluster on page 5‑9.
Head-Up Display (HUD)
{ WARNING
If the HUD image is too bright or too high in your field of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view.
For vehicles with HUD, some information concerning the operation of the vehicle is projected onto the windshield. This includes the speedometer reading, rpm reading, transmission position, compass heading, audio/phone information, and Turn-by-Turn Navigation information. The images are projected through the HUD lens on the driver side of the instrument panel.
HUD Display on the Vehicle
Windshield
The HUD information appears as an image focused out toward the front of the vehicle. The HUD may display different alerts and information for vehicles equipped with these features:
Traction Control System (TCS)
. StabiliTrak System . Collision Alert . Gap Adjust
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (30,1)
5-30
Instruments and Controls
. Upcoming Maneuver from
OnBoard Navigation
. Upcoming Maneuver from
OnStar Incoming Call
When the HUD is on, the speedometer reading is continually displayed, except when an imminent navigation maneuver is being shown. The current audio, phone, or navigation alert temporarily displays if their status changes. This occurs if the steering wheel controls are used to adjust a setting or acknowledge an alert.
The HUD control is to the left of the steering wheel.
To adjust the HUD image so that items are properly displayed: 1. Adjust the driver seat to a
comfortable position.
2. Start the engine. 3. Adjust the HUD controls. Use the following settings to adjust the HUD. $ (Image Adjustment): Press down or lift up to center the HUD image. The HUD image can only be adjusted up and down, not side to side. ! (Display View): Press to select the display view. Release when the desired display is shown on the HUD. If vehicle messages are displayed, pressing the DIC select button may clear the message. See Driver Information Center (DIC) on page 5‑26. D (Brightness): Lift up and hold to brighten the display. Press down and hold to dim the display. Hold down to turn the display off.
There are four views in the HUD display:
Metric
English
Speed View: This display gives the speedometer reading (in English or metric units), speed limit, Adaptive Cruise Control speed, Forward Collision Alert, Lane Departure Warning, and Vehicle Ahead indicator. Some information only appears on vehicles that have these features, and when they are active.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (31,1)
Instruments and Controls
5-31
closer you get to the maneuver. All navigation information is provided to the HUD by the navigation radio or OnStar (if equipped).
Metric
Metric
English
English
Audio/Phone View: This display includes the information in speed view along with audio/phone information. The current radio station, media type, and incoming calls will be displayed.
Navigation View: This display includes the information in speed view along with Turn-by-Turn Navigation information. The compass heading is displayed when navigation routing is not active. All formats will briefly show the Turn-by-Turn Navigation alerts and provide details about the next driving maneuver to be made. When you are near the next maneuver, the HUD displays a distance bar that will empty the
Metric
English
Performance View: This display gives the speedometer reading (in English or metric units), rpm reading, transmission positions, and gear shift indicator.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (32,1)
5-32
Instruments and Controls
The HUD image displayed on the windshield will automatically dim and brighten to compensate for outside lighting. However, the HUD brightness control can still be adjusted as needed. The HUD image can temporarily light up depending on the angle and position of the sunlight on the HUD display. This is normal and will change when the angle of the sunlight on the HUD display changes. Polarized sunglasses could make the HUD image harder to see. Care of the HUD Clean the inside of the windshield as needed to remove any dirt or film that could reduce the sharpness or clarity of the HUD image. To clean the HUD lens, use a soft, clean cloth that has household glass cleaner sprayed on it. Wipe the HUD lens gently, then dry it. Do not
spray cleaner directly on the lens because the cleaner could leak into the unit. If You Cannot See the HUD Image When the Ignition Is On
Is anything covering the HUD lens? Is the HUD dimmer setting bright enough? Is the HUD image adjusted to the proper height?
. Are you wearing polarized
sunglasses?
If the HUD Image Is Not Clear
Is the HUD image too bright? . Are the windshield and HUD
lens clean?
If the HUD image is not correct, contact your dealer. Keep in mind that the windshield is part of the HUD system. See Windshield Replacement on page 10‑30.
Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SEL. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on the vehicle content.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (33,1)
Battery Voltage and Charging Messages
BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10‑26. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.
Instruments and Controls
5-33
TRANSPORT MODE ON This message is displayed when the vehicle is in transport mode. Some features can be disabled while in this mode, including Remote Keyless Entry (RKE), remote start, and the vehicle alarm system. Take the vehicle to your dealer for service to turn transport mode off.
Brake System Messages
BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10‑25. STEP ON BRAKE TO RELEASE PARK BRAKE This message is displayed if you attempt to release the Electric Parking Brake without the brake pedal applied. See Parking Brake (Electric) on page 9‑30 or Parking Brake (Manual) on page 9‑33.
RELEASE PARKING BRAKE This message is displayed if the Electric Parking Brake is on while the vehicle is in motion. See Parking Brake (Electric) on page 9‑30 or Parking Brake (Manual) on page 9‑33. SERVICE BRAKE ASSIST This message may be displayed when there is a problem with the brake boost assist system. When this message is displayed, the brake boost assist motor might be heard operating and you might notice pulsation in the brake pedal. This is normal under these conditions. Take the vehicle to your dealer for service. SERVICE PARKING BRAKE This message is displayed when there is a problem with the parking brake. Take the vehicle to your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (34,1)
5-34
Instruments and Controls
Compass Messages Dashes may be displayed if the vehicle temporarily loses communication with the Global Positioning System (GPS).
Cruise Control Messages
ADAPTIVE CRUISE SET TO XXX This message displays when the Adaptive Cruise Control (ACC) speed is set. See Adaptive Cruise Control on page 9‑42. ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE This message displays when attempting to activate Adaptive Cruise Control (ACC) when it is temporarily unavailable. The ACC system does not need service.
This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance. CRUISE SET TO XXX This message displays when the cruise control speed is set. See Cruise Control on page 9‑39. NO CRUISE BRAKING GAS PEDAL APPLIED This message displays when Adaptive Cruise Control (ACC) is active and the driver is pressing the gas pedal. When this occurs, ACC will not brake. See Adaptive Cruise Control on page 9‑42.
Door Ajar Messages
DOOR OPEN A door open symbol will be displayed on the DIC showing which door is open. If the vehicle has been shifted out of P (Park), a DOOR OPEN message will also be displayed. If the vehicle is in manual shift mode, the DOOR OPEN message will be displayed if the vehicle starts to move. Close the door completely. HOOD OPEN This message will display along with a hood open symbol when the hood is open. Close the hood completely. TRUNK OPEN This message will display along with a symbol when the trunk is open. Close the trunk completely.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (35,1)
Instruments and Controls
5-35
Engine Cooling System Messages
A/C OFF ENGINE COOLANT HOT This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. The vehicle can continue to be driven. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.
ENGINE OVERHEATED — IDLE ENGINE This message displays and a chime sounds when the engine coolant temperature is too hot. The engine coolant temperature warning light will also be on. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — TURN VEHICLE OFF This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. The engine coolant temperature warning light will flash. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.
Engine Oil Messages
CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When you change the engine oil, be sure to reset the Oil Life System. See Engine Oil Life System on page 10‑13, Driver Information Center (DIC) on page 5‑26, Engine Oil on page 10‑11, and Maintenance Schedule on page 11‑3. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (36,1)
5-36
Instruments and Controls
ENGINE OIL LOW — ADD OIL On some vehicles, this message displays when the engine oil level may be too low. Check the oil level before filling to the recommended level. If the oil is not low and this message remains on, take the vehicle to your dealer for service. See Engine Oil on page 10‑11. OIL PRESSURE LOW — STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.
Engine Power Messages
ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate.
If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this message stays on, the vehicle should be taken to your dealer for service as soon as possible.
Fuel System Messages
FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible TIGHTEN GAS CAP This message displays when the fuel cap is not on tight. Tighten the fuel cap.
Key and Lock Messages
NO REMOTE KEY WAS DETECTED PLACE KEY IN TRANSMITTER POCKET THEN START YOUR VEHICLE SEE OWNER’S MANUAL FOR DETAILS This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2‑3. NO REMOTE PRESS BRAKE TO RESTART This message is displayed when attempting to turn off the vehicle and the remote is no longer detected. Restarting is allowed without the remote for five minutes. Press the brake pedal to restart the vehicle.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (37,1)
Instruments and Controls
5-37
NUMBER OF KEYS PROGRAMMED This message displays when programming new keys to the vehicle. REMOTE LEFT IN VEHICLE This message displays when leaving the vehicle with the RKE transmitter still inside. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the RKE transmitter needs to be replaced.
Lamp Messages
AFL (ADAPTIVE FORWARD LIGHTING) LAMPS NEED SERVICE This message displays when the AFL system is disabled and needs service. See your dealer. See Adaptive Forward Lighting (AFL) on page 6‑5. AUTOMATIC LIGHT CONTROL ON/OFF This message is displayed when the exterior lamp control is in AUTO and the lights have turned on or off. See Automatic Headlamp System on page 6‑5.
XXX TURN INDICATOR FAILURE When one of the turn signals is out, this message displays to show which bulb needs to be replaced. See Bulb Replacement on page 10‑31 and Replacement Bulbs on page 10‑33. TURN SIGNAL ON This message is displayed if the turn signal has been left on. Turn off the turn signal.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (38,1)
5-38
Instruments and Controls
Object Detection System Messages
24 GHz RADARS OFF This message displays when driving in certain areas where there may be radar interference. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), and the Active Emergency Braking System may not work or may not work as well. The vehicle does not need service. AUTOMATIC COLLISION PREP UNAVAILABLE This message displays when the Active Emergency Braking System has been unavailable for some time. The Active Emergency Braking System does not need service.
This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance.
This message may also be displayed if there is a problem with the StabiliTrak system. FORWARD COLLISION ALERT OFF This message displays when the Forward Collision Alert has been turned off.
FRONT CAMERA BLOCKED CLEAN WINDSHIELD This message displays when the camera is blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue. The Lane Departure Warning system will not operate. Forward Collision Alert (FCA) may not work or may not work as well. LANE DEPARTURE WARNING UNAVAILABLE This message displays when attempting to activate the Lane Departure Warning (LDW) system when it is temporarily unavailable. The LDW system does not need service. This message could be due to the camera being blocked. Cleaning the outside of the windshield behind the rearview mirror may correct the issue.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (39,1)
Instruments and Controls
5-39
PARK ASSIST OFF This message displays when the Parking Assist system has been turned off or when there is a temporary condition causing the system to be disabled. REAR AUTO BRAKE AND PARK ASSIST UNAVAILABLE This message displays when attempting to activate the parking and backing features of the Driver Assistance System when they are temporarily unavailable. The system does not need service. This can occur under the following conditions:
The radar is not clean. Keep the radar sensors free of mud, dirt, snow, ice, and slush. Clean the entire front and/or rear of the vehicle. For cleaning instructions, see Exterior Care on page 10‑81.
. Heavy rain or snow is interfering with the radar object detection or camera performance.
See Driver Assistance Systems on page 9‑50. SERVICE AUTOMATIC COLLISION PREP If this message displays, take the vehicle to your dealer to repair the system. SERVICE DRIVER ASSIST SYSTEM If this message displays, take the vehicle to your dealer to repair the system. Adaptive Cruise Control (ACC), Forward Collision Alert (FCA), Active Emergency Braking System, Assistance Systems for Parking or Backing, and/or Lane Departure Warning (LDW) system may not work. Do not use these systems until the vehicle has been repaired.
SERVICE FRONT CAMERA If this message remains on after continued driving, the vehicle needs service. Do not use the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) features. Take the vehicle to your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Parking Assist system. Do not use this system to help you park. See your dealer for service. SERVICE REAR AUTO BRAKE AND PARK ASSIST This message displays if there is a problem with the parking and backing features of the Driver Assistance System. Do not use this system to help park or back the vehicle. See your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (40,1)
5-40
Instruments and Controls
SIDE BLIND ZONE ALERT OFF This message indicates that the driver has turned the Side Blind Zone Alert (SBZA) system off. SERVICE SIDE DETECTION SYSTEM If this message remains on after continued driving, the vehicle needs service. Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) features will not work. Take the vehicle to your dealer. SIDE DETECTION SYSTEM UNAVAILABLE This message indicates that Side Blind Zone Alert (SBZA) and Rear Cross Traffic Alert (RCTA) are disabled either because the sensor is blocked and cannot detect vehicles in the blind zone, or the vehicle is passing through an open area, such as the desert, where there is insufficient data for operation. This message may also activate during heavy rain or due to road spray. The vehicle does not
need service. For cleaning, see "Washing the Vehicle" under Exterior Care on page 10‑81.
Ride Control System Messages
ALL WHEEL DRIVE OFF If the vehicle has the All-Wheel-Drive (AWD) system, this message displays when there is a temporary condition making the AWD system unavailable. The vehicle will run in 2WD. This could be caused by:
Loss of wheel or vehicle speed
. AWD system overheat . Certain vehicle electrical
conditions
This message turns off when the above conditions are no longer present and the warning message is reset. See All-Wheel Drive on page 9‑29.
SERVICE ALL WHEEL DRIVE This message displays if a problem occurs with the All-Wheel-Drive (AWD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . Worn out or overheated clutch
plates
. Various electrical issues The system may need service. See your dealer. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. See StabiliTrak® System on page 9‑36. SERVICE SUSPENSION SYSTEM This message displays when there is a problem with the MagneRide™ system. See Driver Mode Control on page 9‑37. Have the vehicle serviced by your dealer.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (41,1)
Instruments and Controls
5-41
SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). See Traction Control System (TCS) on page 9‑34. TRACTION CONTROL OFF This message may display when the Traction Control System (TCS) has been turned off. See Traction Control System (TCS) on page 9‑34
TRACTION CONTROL ON This message may display when the Traction Control System (TCS) has been turned on. See Traction Control System (TCS) on page 9‑34Airbag System Messages
SERVICE AIRBAG This message displays if there is a problem with the airbag system. Take the vehicle to your dealer for service.
Security Messages
THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.
Service Vehicle Messages
SERVICE AC SYSTEM This message displays if there is a problem with the air conditioning system. Take the vehicle to your dealer for service. SERVICE POWER STEERING This message displays if there is a problem with the power steering system. Take the vehicle to your dealer for service. SERVICE STEERING COLUMN LOCK This message displays if there is a problem with the steering column lock. Take the vehicle to your dealer for service.
SERVICE VEHICLE SOON This message displays if there is a problem with the vehicle. Take the vehicle to your dealer for service.
Starting the Vehicle Messages
PRESS BRAKE TO START VEHICLE This message is displayed when attempting to start the vehicle without first pressing the brake pedal. SERVICE KEYLESS START SYSTEM This message is displayed if there is a problem with the pushbutton start system. Take the vehicle to your dealer for service.
Cadillac ATS Owner Manual - 2013 - CRC - 10/5/12
Black plate (42,1)
5-42
Instruments and Controls
TURN STEERING WHEEL START VEHICLE AGAIN This message may display when you try to start the vehicle, but the column remains locked. Try turning the steering wheel while starting the vehicle to unlock the steering column. If the vehicle still does not start, turn the steering wheel the other way, and try starting the vehicle again.
Tire Messages
SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑53. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10‑53.
TIRE LOW ADD AIR TO TIRE This message displays when the pressure in one or more of the tires is low. This message also displays LEFT FRONT, RIGHT FRONT, LEFT REAR, or RIGHT REAR to indicate the location of the low tire. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5‑22. If a tire pressure message appears on the DIC, stop as soon as you can. Inflate the tires by adding air until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10‑42, Vehicle Load Limits on page 9‑11, and Tire Pressure on page 10‑50. You can receive more than one tire pressure message at a time. The DIC also shows the tire pressure values. See Driver Information
