Download PDF Manual

If the indicator needle moves to the hot side of the gauge toward the shaded area, the engine is too hot. If the vehicle has been operated under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.


When the vehicle is started, this light flashes and a chime may come on to remind the driver to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle may continue several times if the driver remains or becomes unbuckled while the vehicle is moving. If the driver safety belt is buckled, neither the light nor the chime comes on.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (12,1)


5-12


Instruments and Controls


Passenger Safety Belt Reminder Light There is a passenger safety belt reminder light near the passenger airbag status indicator. See Passenger Sensing System on page 3-24.


When the vehicle is started, this light flashes and a chime may come on to remind passengers to fasten their safety belt. Then the light stays on solid until the belt is buckled. This cycle continues several times if the passenger remains or becomes unbuckled while the vehicle is moving. If the passenger safety belt is buckled, neither the chime nor the light comes on.


The front passenger safety belt warning light and chime may turn on if an object is put on the seat such as a briefcase, handbag, grocery bag, laptop, or other electronic device. To turn off the warning light and/or chime, remove the object from the seat or buckle the safety belt.


Airbag Readiness Light This light shows if there is an electrical problem with the airbag system. The system check includes the airbag sensor(s), passenger sensing system, the pretensioners, the airbag modules, the wiring, and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 3-17.


The airbag readiness light comes on for several seconds when the vehicle is started. If the light does not come on then, have it fixed immediately.


{ Warning


If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly. The airbags in the vehicle might not inflate in a crash, or they could even inflate without a crash. To help avoid injury, have the vehicle serviced right away.


Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 3-24 for


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (13,1)


important safety information. The center stack has a passenger airbag status indicator.


When the vehicle is started, the passenger airbag status indicator will light ON and OFF for several seconds as a system check. Then, after several seconds, the status indicator will light either ON or OFF to let you know the status of the front outboard passenger frontal airbag and knee airbag. If the word ON is lit on the passenger airbag status indicator, it means that the front outboard passenger frontal airbag and knee airbag are allowed to inflate. If the word OFF is lit on the passenger airbag status indicator, it means that the passenger sensing


Instruments and Controls


5-13


system has turned off the front outboard passenger frontal airbag and passenger knee airbag. If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service.


{ Warning


If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 5-12 for more information, including important safety information.


Charging System Light


The charging system light comes on briefly when the ignition is turned on, but the engine is not running, as a check to show the light is working. The light turns off when the engine is started. If it does not, have the vehicle serviced by your dealer. If the light stays on, or comes on while driving, there could be a problem with the electrical charging system. Have it checked by your dealer. Driving while this light is on could drain the battery. If a short distance must be driven with the light on, be sure to turn off all accessories, such as the radio and air conditioner.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (14,1)


5-14


Instruments and Controls


Malfunction Indicator Lamp A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors the operation of the vehicle to ensure emissions are at acceptable levels, helping to maintain a clean environment. The malfunction indicator lamp comes on when the vehicle is placed in ON/RUN for Key Access or Service Only Mode for Keyless Access, as a check to show it is working. If it does not, have the vehicle serviced by your dealer. See Ignition Positions (Keyless Access) on page 9-14 or Ignition Positions (Key Access) on page 9-16 for more information.


If the malfunction indicator lamp comes on while the engine is running, this indicates that the OBD II system has detected a problem and diagnosis and service might be required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system also assists the dealer technician in correctly diagnosing any malfunction.


{ Caution


If the vehicle is continually driven with this light on, the emission controls might not work as well, the vehicle fuel economy might not be as good, and the engine might not run as smoothly. This could lead to costly repairs that might not be covered by the vehicle warranty.


{ Caution


Modifications made to the engine, transmission, exhaust, intake, or fuel system of the vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect the vehicle's emission controls and can cause this light to come on. Modifications to these systems could lead to costly repairs not covered by the vehicle warranty. This could also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modifications on page 10-3.


This light comes on during a malfunction in one of two ways: Light Flashing: A misfire condition has been detected. A misfire increases vehicle emissions and


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (15,1)


could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. If the light continues to flash, find a safe place to stop and park the vehicle. Turn the vehicle off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required.


Instruments and Controls


5-15


The following may correct an emission control system malfunction: . Check that the fuel cap is fully


installed. See Filling the Tank on page 9-50. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap allows fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off.


. Check that good quality fuel is used. Poor fuel quality causes the engine not to run as efficiently as designed and may cause stalling after start-up, stalling when the vehicle is changed into gear, misfiring, hesitation on acceleration, or stumbling on acceleration. These conditions might go away once the engine is warmed up.


If one or more of these conditions occurs, change the fuel brand used. It may require at least one full tank of the proper fuel to turn the light off. See Recommended Fuel on page 9-48. If none of the above have made the light turn off, your dealer can check the vehicle. The dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Depending on where you live, your vehicle may be required to participate in an emission control system inspection and maintenance program. For the inspection, the emission system test equipment will likely connect to the vehicle's Data Link Connector (DLC).


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (16,1)


5-16


Instruments and Controls


The DLC is under the instrument panel next to the steering wheel. See your dealer if assistance is needed. The vehicle may not pass inspection if:


The malfunction indicator lamp is on while the engine is running, or the malfunction indicator lamp is not on while the vehicle is in ON/RUN or Service Only Mode. See your dealer for assistance in verifying proper operation of the malfunction indicator lamp.


The OBD II (On-Board Diagnostics) system determines that critical emission control systems have not been completely diagnosed by the system. If this were to occur, the vehicle would be considered not ready for inspection. This can happen if the 12-volt battery has recently been replaced or run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This can take several days of driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer can prepare the vehicle for inspection.


Brake System Warning Light The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working. The brake system warning light will come on with the electric parking brake light when the electric parking brake is applied. Both lights will stay on until the electric parking brake is released. The brake system warning light will also come on when there is a brake problem. If the warning light stays on when the electric parking brake is not applied, have the vehicle inspected by your dealer right away.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (17,1)


Instruments and Controls


5-17


If the light comes on while driving, a chime sounds. Pull off the road and stop. The pedal might be harder to push or go closer to the floor. It might also take longer to stop. If the light is still on, have the vehicle towed for service. See Towing the Vehicle on page 10-72.


Electric Parking Brake Light


released, or while driving, there is a problem with the EPB system. A message may also display in the Driver Information Center (DIC). See Brake System Messages on page 5-26 for more information. The brake system warning light will come on with the electric parking brake light when the electric parking brake is applied. Both lights will stay on until the electric parking brake is released. If the light does not come on, or remains flashing, see your dealer.


The Electric Parking Brake (EPB) light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. The parking brake status light comes on when the brake is applied. If the light continues flashing after the parking brake is


If this light comes on, there is a problem with a system on the vehicle that is causing the EPB to work at a reduced level. The vehicle can still be driven, but should be


Metric


English


The brake indicator light should come on briefly as the engine is started. If it does not come on have the vehicle serviced by your dealer.


{ Warning


The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (18,1)


5-18


Instruments and Controls


taken to a dealer as soon as possible. See Parking Brake on page 9-31 for more information.


Antilock Brake System (ABS) Warning Light


The Antilock Brake System (ABS) light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the ABS light comes on and stays on while driving, stop as soon as possible and turn the ignition off. Start the engine again to reset the system. If the light stays on after driving at a speed above 20 km/h (13 mph), see your dealer for service. A chime may also sound when the light comes on steady.


If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes. See Brake System Warning Light on page 5-16. See Brake System Messages on page 5-26 for all brake‐related DIC messages.


Lane Departure Warning (LDW) Light


This light comes on green when the system is on and ready to operate. When the system determines that the vehicle is leaving its lane without using the turn signal, this light will change to amber and flash. See Lane Departure Warning (LDW) on page 9-46.


Vehicle Ahead Indicator


If available, this light displays green when a vehicle is detected ahead. See Forward Collision Alert (FCA) System on page 9-38.


This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the light then turns off.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (19,1)


Traction Off Light


StabiliTrak® OFF Light


Instruments and Controls


5-19


Traction Control System (TCS)/StabiliTrak® Light


This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. If the system is working normally, the indicator light then turns off. The traction off light comes on when the Traction Control System (TCS) has been turned off by pressing and releasing the TCS/StabiliTrak button. This light and the StabiliTrak OFF light come on when StabiliTrak is turned off. If the TCS is off, wheel spin is not limited. Adjust driving accordingly. See Traction Control/Electronic Stability Control on page 9-33.


This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer. This light comes on when the StabiliTrak system is turned off. If StabiliTrak is off, the Traction Control System (TCS) is also off. If the StabiliTrak and TCS are off, the system does not assist in controlling the vehicle. Turn on the TCS and the StabiliTrak systems and the warning light turns off. See Traction Control/Electronic Stability Control on page 9-33.


This light comes on briefly when the engine is started. If the light does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light is on and not flashing, the TCS, and potentially the StabiliTrak system have been disabled. A DIC message may display. Check the DIC messages to determine which feature(s) is no longer functioning and whether the vehicle requires service.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (20,1)


5-20


Instruments and Controls


If the indicator/warning light is on and flashing, the TCS and/or the StabiliTrak system is actively working. See Traction Control/Electronic Stability Control on page 9-33.


Tire Pressure Light


For vehicles with the Tire Pressure Monitor System (TPMS), this light comes on briefly when the engine is started. It provides information about tire pressures and the TPMS.


When the Light Is On Steady This indicates that one or more of the tires are significantly underinflated.


A Driver Information Center (DIC) tire pressure message may also display. See Tire Messages on page 5-31. Stop as soon as possible, and inflate the tires to the pressure value shown on the Tire and Loading Information label. See Tire Pressure on page 10-47.


When the Light Flashes First and Then Is On Steady If the light flashes for about a minute and then stays on, there may be a problem with the TPMS. If the problem is not corrected, the light will come on at every ignition cycle. See Tire Pressure Monitor Operation on page 10-49.


Engine Oil Pressure Light


{ Caution Lack of proper engine oil maintenance can damage the engine. Driving with the engine


(Continued)


Caution (Continued)


low can also damage the


oil engine. The repairs would not be covered by the vehicle warranty. Check the oil level as soon as possible. Add oil if required, but if the oil level is within the operating range and the oil pressure is still low, have the vehicle serviced. Always follow the maintenance schedule for changing engine oil.


This light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (21,1)


could be low on oil and might have some other system problem. See your dealer.


For more information on the Driver Information Center (DIC), see Fuel System Messages on page 5-29.


Low Fuel Warning Light


Security Light


High-Beam On Light


Instruments and Controls


5-21


The security light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. If the system is working normally, the indicator light turns off. If the light stays on and the engine does not start, there could be a problem with the theft-deterrent system. See Immobilizer Operation (Key Access) on page 2-17 or Immobilizer Operation (Keyless Access) on page 2-18.


The high‐beam on light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 6-2 for more information.


Front Fog Lamp Light


For vehicles with front fog lamps, this light comes on when the front fog lamps are in use.


This light comes on for a few seconds when the ignition is turned on as a check to indicate it is working. If it does not come on, have it fixed. The low fuel warning light comes on and a chime sounds when the vehicle is low on fuel. The light turns off when fuel is added to the fuel tank.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (22,1)


5-22


Instruments and Controls


The light goes out when the front fog lamps are turned off. See Front Fog Lamps on page 6-4 for more information.


Lamps On Reminder


For vehicles with cruise control, the cruise control light is white when the cruise control is on and ready, and turns green when the cruise control is set and active. The light turns off when the cruise control is turned off. See Cruise Control on page 9-35.


Door Ajar Light


This light comes on when the exterior lamps are in use. See Exterior Lamp Controls on page 6-1.


Cruise Control Light


If equipped, this light comes on when a door is open or not securely latched. Before driving, check that all doors are properly closed. See Door Ajar Messages on page 5-27.


Information Displays


Driver Information Center (DIC) The Driver Information Center (DIC) displays information about the vehicle. It also displays warning messages if a system problem is detected. See Vehicle Messages on page 5-26. All messages appear in the DIC display in the center of the instrument cluster. On some models, the DIC may have some warning lights or indicators shown in the top portion of the display. See Warning Lights, Gauges, and Indicators on page 5-8. The vehicle may also have features that can be customized through the controls on the radio. See Vehicle Personalization on page 5-32.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (23,1)


DIC Operation and Displays The DIC has different displays which can be accessed by using the DIC buttons on the turn signal lever. The DIC displays trip, fuel, and vehicle system information, and warning messages if a system problem is detected. The bottom of the DIC display shows the position of the shift lever and the odometer. It may also show the direction the vehicle is driving. In cold weather the DIC display may change slowly. This is normal and will move more quickly as the vehicle's interior temperature rises.


DIC Buttons


Instruments and Controls


5-23


1. SET/CLR (Set/Clear): Press to set or clear the menu item when it is displayed.


2. w / x (Thumbwheel): Use to scroll through the items in each menu. A small marker will move across the bottom of the page as you scroll through the items. This shows where each page is in the menu.


3. MENU: Press to get to the Trip/


Fuel Menu and the Vehicle Information Menu. This button is also used to return to or exit the last screen displayed on the DIC.


Trip/Fuel Menu Items Press MENU on the turn signal lever until the Trip/Fuel Menu is displayed. Use w / x to scroll through the following menu items: . Digital Speedometer


Trip 1
Trip 2


Fuel Range


. Average Fuel Economy


Instantaneous Fuel Economy


. Average Vehicle Speed


Timer


. Navigation . Blank Display


Digital Speedometer The speedometer shows how fast the vehicle is moving in either kilometers per hour (km/h) or miles per hour (mph). The speedometer cannot be reset.


Trip 1 and Trip 2
These displays show the current distance traveled, in either kilometers (km) or miles (mi), since the last reset for the trip odometer. The trip odometer can be reset to zero by pressing SET/CLR, or the trip odometer reset stem in the cluster, while the trip odometer display is showing.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (24,1)


5-24


Instruments and Controls


Fuel Range This display shows the approximate distance the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank. Fuel range cannot be reset.


Average Fuel Economy This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). Average fuel economy is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset. The average fuel economy can be reset by pressing SET/CLR while the Average Fuel Economy display is showing.


Instantaneous Fuel Economy The instantaneous fuel economy display shows the current fuel economy in liters per 100 kilometers (L/100 km) or miles per gallon


(mpg). The instantaneous fuel economy reflects only the current fuel economy and changes frequently as driving conditions change. Unlike average economy, this display cannot be reset.


Average Vehicle Speed This display shows the average speed of the vehicle in kilometers per hour (km/h) or miles per hour (mph). This average is calculated based on the various vehicle speeds recorded since the last reset of this value. The average speed can be reset by pressing SET/CLR while the Average Vehicle Speed display is showing.


Timer This display can be used as a timer. To start the timer, press SET/CLR while Timer is displayed. The display will show the amount of time that has passed since the timer was last reset, not including time the ignition is off. Time will continue to be counted as long as the ignition is on, even if another display is being


shown on the DIC. The timer will record up to 99 hours, 59 minutes, and 59 seconds (99:59:59) after which the display will return to zero. To stop the timer, press SET/CLR briefly while Timer is displayed. To reset the timer to zero, press and hold SET/CLR.


Navigation This display is used for the Navigation System Turn-by-Turn guidance. See the infotainment manual, if the vehicle has navigation, for more information.


Blank Display This display shows no information. Vehicle Information Menu Items Press MENU on the turn signal lever until the Vehicle Information Menu is displayed. Use w / x to scroll through the following menu items: . Unit


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (25,1)


Tire Pressure


. Remaining Oil Life . Battery Voltage


Unit Press SET/CLR to set. Move w / x to switch between metric or US when the set Unit display is active. Press SET/CLR to confirm the setting. This will change the displays on the cluster and DIC to either metric or English (US) measurements.


Tire Pressure The display will show a vehicle with the approximate pressures of all four tires. Tire pressure is displayed in either kilopascal (kPa) or pounds per square inch (psi). See Tire Pressure Monitor System on page 10-48 and Tire Pressure Monitor Operation on page 10-49 for more information.


Instruments and Controls


5-25


Remaining Oil Life This display shows an estimate of the oil's remaining useful life. If REMAINING OIL LIFE 99% is displayed, that means 99% of the current oil life remains. When the remaining oil life is low, the CHANGE ENGINE OIL SOON message will appear on the display. See Engine Oil Messages on page 5-28. The oil should be changed as soon as possible. See Engine Oil on page 10-9. In addition to the Engine Oil Life System monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Maintenance Schedule on page 11-2 for more information. Remember, the Remaining Oil Life display must be reset after each oil change. It will not reset itself. Also, be careful not to reset the Remaining Oil Life display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until


the next oil change. To reset the Engine Oil Life System, press SET/ CLR while the Remaining Oil Life display is active. See Engine Oil Life System on page 10-11.


Battery Voltage This display shows the current battery voltage. If the voltage is in the normal range, the value will display. For example, the display may read Battery Voltage 15.0
Volts. The vehicle's charging system regulates voltage based on the state of the battery. The battery voltage can fluctuate while viewing this information on the DIC. This is normal. See Charging System Light on page 5-13 for more information. If there is a problem with the battery charging system, the DIC will display a message Compass The vehicle has a compass display in the DIC. See Compass on page 5-4 for more information.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (26,1)


5-26


Instruments and Controls


Vehicle Messages Messages displayed on the DIC indicate the status of the vehicle or some action that may be needed to correct a condition. Multiple messages may display one after the other. The messages that do not require immediate action can be acknowledged and cleared by pressing SET/CLR. The messages that require immediate action cannot be cleared until that action is performed. All messages should be taken seriously and clearing the messages does not correct the problem. The following are some of the vehicle messages that may be displayed depending on your vehicle content.


Battery Voltage and Charging Messages


BATTERY SAVER ACTIVE This message displays when the vehicle has detected that the battery voltage is dropping beyond a reasonable point. The battery saver system starts reducing features of the vehicle that may be noticed. At the point that features are disabled, this message displays. Turn off unnecessary accessories to allow the battery to recharge. LOW BATTERY This message is displayed when the battery voltage is low. See Battery on page 10-24. SERVICE BATTERY CHARGING SYSTEM This message is displayed when there is a fault in the battery charging system. Take the vehicle to your dealer for service.


Brake System Messages


BRAKE FLUID LOW This message is displayed when the brake fluid level is low. See Brake Fluid on page 10-22. HILL START ASSIST ACTIVE This message is displayed when Hill Start Assist (HSA) is preventing the vehicle from rolling while driving off on a grade. See Hill Start Assist (HSA) on page 9-33. PRESS BRAKE PEDAL TO RELEASE PARK BRAKE This message is displayed if you attempt to release the electric parking brake without the brake pedal applied. See Parking Brake on page 9-31 for more information. RELEASE PARK BRAKE SWITCH This message is displayed if the electric parking brake is applied while the vehicle is in motion.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (27,1)


Release it before you attempt to drive. See Parking Brake on page 9-31 for more information. SERVICE PARKING BRAKE This message is displayed when there is a problem with the electric parking brake. See Parking Brake on page 9-31 for more information. Take the vehicle to your dealer.


Compass Messages


CAL This message is displayed when the compass needs to be calibrated. See Compass on page 5-4. – – Dashes will be displayed if the compass needs service. See your dealer for service.


Instruments and Controls


5-27


Door Ajar Messages


DRIVER DOOR OPEN This message may display when the driver door is open. Close the door completely. HOOD OPEN This message will display when the hood is open. Close the hood completely. LEFT REAR DOOR OPEN This message may display when the driver side rear door is open. Close the door completely. PASSENGER DOOR OPEN This message may display when the front passenger door is open. Close the door completely. RIGHT REAR DOOR OPEN This message may display when the passenger side rear door is open. Close the door completely.


TRUNK OPEN This message will display when the trunk is open. Close the trunk completely.


Engine Cooling System Messages


A/C OFF DUE TO HIGH ENGINE TEMP This message displays when the engine coolant becomes hotter than the normal operating temperature. To avoid added strain on a hot engine, the air conditioning compressor automatically turns off. When the coolant temperature returns to normal, the air conditioning compressor turns back on. The vehicle can continue to be driven. If this message continues to appear, have the system repaired by your dealer as soon as possible to avoid damage to the engine.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (28,1)


5-28


Instruments and Controls


COOLANT LEVEL LOW ADD COOLANT This message will display if the coolant is low. See Engine Coolant on page 10-16. ENGINE OVERHEATED — IDLE ENGINE This message displays when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. ENGINE OVERHEATED — STOP ENGINE This message displays and a continuous chime sounds if the engine cooling system reaches unsafe temperatures for operation. Stop and turn off the vehicle as soon as it is safe to do so to avoid severe damage. This message clears when the engine has cooled to a safe operating temperature.


HIGH COOLANT TEMPERATURE This message displays if the coolant temperature is hot. See Engine Overheating on page 10-19.


Engine Oil Messages


CHANGE ENGINE OIL SOON This message displays when the engine oil needs to be changed. When the engine oil is changed, be sure to reset the Oil Life System. See Engine Oil Life System on page 10-11, Driver Information Center (DIC) on page 5-22, Engine Oil on page 10-9, and Maintenance Schedule on page 11-2. ENGINE OIL HOT, IDLE ENGINE This message displays when the engine oil temperature is too hot. Stop and allow the vehicle to idle until it cools down.


OIL PRESSURE LOW— STOP ENGINE This message displays if low oil pressure levels occur. Stop the vehicle as soon as safely possible and do not operate it until the cause of the low oil pressure has been corrected. Check the oil as soon as possible and have the vehicle serviced by your dealer.


Engine Power Messages


ENGINE POWER IS REDUCED This message displays when the vehicle's engine power is reduced. Reduced engine power can affect the vehicle's ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven. The vehicle may be driven at a reduced speed while this message is on, but maximum acceleration and speed may be reduced. Anytime this


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (29,1)


Instruments and Controls


5-29


message stays on, the vehicle should be taken to your dealer for service as soon as possible.


Fuel System Messages


FUEL LEVEL LOW This message displays when the vehicle is low on fuel. Refuel as soon as possible.


Key and Lock Messages


NO REMOTE DETECTED This message displays when the transmitter battery is weak on vehicles with Keyless Access. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2-3. REPLACE BATTERY IN REMOTE KEY This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. See “Battery


Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-3. USE TRANSMITTER POCKET TO START This message displays when trying to start the vehicle if an RKE transmitter is not detected. The transmitter battery may be weak. See “Starting the Vehicle with a Low Transmitter Battery” under Remote Keyless Entry (RKE) System Operation on page 2-3.


Object Detection System Messages


FORWARD COLLISION ALERT OFF If your vehicle has the Forward Collision Alert (FCA) system, this message may display if the FCA system cannot activate due to a temporary condition. See Forward Collision Alert (FCA) System on page 9-38.


FRONT CAMERA BLOCKED, CLEAN WINDSHIELD This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled because the camera view is blocked and cannot operate properly. It may also activate during heavy rain or due to road spray. To clean the system, clean the outside of the windshield area in front of the LDW/FCA camera sensor. LANE DEPARTURE SYSTEM UNAVAILABLE If your vehicle has the Lane Departure Warning (LDW) system, this message may display if the LDW system cannot activate due to a temporary condition. See Lane Departure Warning (LDW) on page 9-46 for more information. PARK ASSIST OFF This message displays when the park assist system has been turned off or when there is a temporary


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (30,1)


5-30


Instruments and Controls


condition causing the system to be disabled. See Ultrasonic Parking Assist on page 9-39. SERVICE FRONT CAMERA This message displays when the Lane Departure Warning (LDW) and Forward Collision Alert (FCA) systems are disabled and need service. See your dealer. SERVICE PARK ASSIST This message displays if there is a problem with the Ultrasonic Rear Parking Assist (URPA) system. Do not use this system to help you park. See Ultrasonic Parking Assist on page 9-39 for more information. SERVICE BLIND ZONE ALERT SYSTEM If this message appears, there is a problem with the SBZA system. If the message persists after continued driving, the system needs service. Take the vehicle to your dealer.


SIDE BLIND ZONE ALERT SYSTEM OFF This message indicates that the driver has turned the system off. SIDE BLIND ZONE SYS. UNAVAILABLE This message indicates that the SBZA system is disabled because the sensor is blocked and cannot detect vehicles in the blind zone. The sensor may be blocked by mud, dirt, snow, ice, or slush. This message may also activate during heavy rain or due to road spray. The vehicle does not need service. For cleaning, see Side Blind Zone Alert (SBZA) on page 9-41.


Ride Control System Messages


SERVICE TRACTION CONTROL This message displays when there is a problem with the Traction Control System (TCS). When this


message is displayed, the system will not limit wheel spin. Adjust your driving accordingly. See your dealer for service. SERVICE STABILITRAK This message displays if there is a problem with the StabiliTrak system. If this message appears, try to reset the system. Stop; turn off the engine for at least 15 seconds; then start the engine again. If this message still comes on, it means there is a problem. See your dealer for service. The vehicle is safe to drive; however, you do not have the benefit of StabiliTrak, so reduce your speed and drive accordingly. TRACTION CONTROL OFF This message displays when the Traction Control System (TCS) is turned off. Adjust your driving accordingly.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (31,1)


Instruments and Controls


5-31


TRACTION CONTROL ON This message displays when the Traction Control System (TCS) is turned on.


Security Messages


THEFT ATTEMPTED This message displays if the vehicle detects a tamper condition.


Tire Messages


SERVICE TIRE MONITOR SYSTEM This message displays if there is a problem with the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10-49. TIRE LEARNING ACTIVE This message displays when the system is learning new tires. See Tire Pressure Monitor Operation on page 10-49.


TIRE PRESSURE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires is low. The low tire pressure warning light will also come on. See Tire Pressure Light on page 5-20. If a tire pressure message displays, inflate the tires until the tire pressure is equal to the values shown on the Tire and Loading Information label. See Tires on page 10-39, Vehicle Load Limits on page 9-9, and Tire Pressure on page 10-47. More than one tire pressure message can be received at a time. The DIC also shows the tire pressure values. See Driver Information Center (DIC) on page 5-22.


Transmission Messages


SERVICE TRANSMISSION This message displays if there is a problem with the transmission. See your dealer. SHIFT TO PARK This message displays when the transmission needs to be shifted to P (Park). This may appear when attempting to remove the key from the ignition or from the vehicle if the vehicle is not in P (Park). TRANSMISSION HOT — IDLE ENGINE This message displays and a chime sounds if the transmission fluid in the vehicle gets hot. Driving with the transmission fluid temperature high can cause damage to the vehicle. Stop the vehicle and let it idle to allow the transmission to cool. This message clears when the fluid temperature reaches a safe level.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (32,1)


5-32


Instruments and Controls


Washer Fluid Messages


WASHER FLUID LOW ADD FLUID This message may display when the washer fluid level is low. See Washer Fluid on page 10-21.


Window Messages


OPEN, THEN CLOSE DRIVER/ PASSENGER WINDOW This message is displayed when the window needs to be reprogrammed. If the vehicle's battery has been recharged or disconnected, you will need to program each front window for the express-up feature to work. See Power Windows on page 2-21.


Vehicle Personalization Use the audio system controls to access the personalization menus for customizing vehicle features. The following are all possible personalization features. Depending on the vehicle, some may not be available. CONFIG (Configuration): Press to access the Configuration Settings menu. TUNE/MENU: Press the center of this knob to enter the menus and select menu items. This feature is unavailable with navigation radios. Turn the knob to scroll through the menus. / BACK: Press to exit or move backward in a menu.


Entering the Personalization Menus 1. Press CONFIG to access the Configuration Settings menu.


2. Turn the TUNE/MENU knob to


highlight Vehicle Settings. Press the CONFIG button until Vehicle is highlighted on vehicles with a navigation system only.


3. Press the center of the TUNE/


MENU knob to select the Vehicle Settings menu. The key must be in the ON/RUN position.


The following list of menu items may be available: . Climate and Air Quality . Comfort and Convenience . Collision Detection Systems


Lighting


. Power Door Locks . Remote Lock/Unlock/Start . Return to Factory Settings? Turn the TUNE/MENU knob to highlight the menu. Press the TUNE/MENU knob to select it. Each of the menus is detailed in the following information.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (33,1)


Instruments and Controls


5-33


Vehicles with a navigation system will display a checkmark to indicate this feature is on. Climate and Air Quality If equipped, select the Climate and Air Quality menu and the following may be displayed: . Auto Fan Speed . Remote Start Auto Heat Seats . Auto Defog . Auto Rear Defog


Auto Fan Speed This will allow you to select the automatic fan speed. This feature sets the climate control fan speed to maintain the interior temperature. Press the TUNE/MENU knob when Auto Fan Speed is highlighted to open the menu. Turn the knob to highlight High, Medium, or Low. Press / BACK to confirm the selection and move back to the last menu.


Remote Start Auto Heat Seats On vehicles with remote start and heated seats, the heated seats can be set to on or off. Press the TUNE/MENU knob when Remote Start Auto Heat Seats is highlighted to open the menu. Turn the knob to highlight On or Off. Press / BACK to confirm the selection and move back to the last menu.


Auto Defog When turned on and high humidity is detected, the climate control system may adjust to outside air supply and turn on the air conditioner or the heater. The fan speed may slightly increase to help prevent fogging. When high humidity is no longer detected, the system will return to its prior operation. Press the TUNE/MENU knob when Auto Defog is highlighted to open the menu. Turn the knob to highlight


On or Off. Press / BACK to confirm the selection and move back to the last menu.


Auto Rear Defog When on, this feature turns on the rear defogger at vehicle start when the interior temperature is cold and fog is likely. The auto rear defog function can be disabled by pressing 1. When off, the feature can be turned on by pressing 1. See “Rear Window Defogger” under Climate Control Systems on page 8-1 for more information. Press the TUNE/MENU knob when Auto Rear Defog is highlighted to open the menu. Turn the knob to highlight On or Off. Press the TUNE/MENU knob to confirm the selection and move back to the last menu. Comfort and Convenience Select the Comfort and Convenience menu and Chime Volume may be displayed.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (34,1)


5-34


Instruments and Controls


Chime Volume This allows the selection of the chime volume level. Press the TUNE/MENU knob when Chime Volume is highlighted. Turn the knob to select Normal or High. Press / BACK to confirm and go back to the last menu. Collision Detection Systems If equipped, select the Collision Detection Systems menu and Park Assist may be displayed. . Park Assist . Side Blind Zone Alert


Park Assist This allows the Ultrasonic Rear Parking Assist feature to be turned on or off. Press the TUNE/MENU knob when Park Assist is highlighted. Turn the knob to select On or Off. Press the TUNE/MENU knob to confirm and go back to the last menu.


Side Blind Zone Alert This allows the Side Blind Zone Alert feature to be turned on or off. Press the TUNE/MENU knob when Side Blind Zone Alert is highlighted. Turn the knob to select On or Off. Press the TUNE/MENU knob to confirm and go back to the last menu. Lighting Select the Lighting menu and the following may be displayed: . Exit Lighting . Vehicle Locator Lights


Exit Lighting This allows the selection of how long the exterior lamps stay on when leaving the vehicle when it is dark outside. Press the TUNE/MENU knob when Exit Lighting is highlighted. Turn the knob to select Off, 30 Seconds, , or . Press / BACK to confirm and go back to the last menu.


Vehicle Locator Lights This allows the vehicle locator lights to be turned on or off. When on, the headlamps and back-up lamps turn on and the turn signals will flash when K is pressed. Press the TUNE/MENU knob when Vehicle Locator Lights is highlighted to open the menu. Turn the TUNE/ MENU knob to highlight On or Off. Press TUNE/MENU to select On or Off. Press / BACK to confirm the selection and move back to the last menu. Power Door Locks Select Power Door Locks and the following may be displayed: . Open Door Anti Lock Out . Auto Door Unlock . Delay Door Lock


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (35,1)


Instruments and Controls


5-35


Press the TUNE/MENU knob when Auto Door Unlock is highlighted. Turn the knob to select All Doors, Driver Door, or Off. Press the TUNE/ MENU knob to confirm and press BACK to go back to the last menu. Press / BACK to return to the last menu.


Delay Door Lock When on, this feature will delay the locking of the doors until five seconds after the last door is closed. Press either the power lock button or Q on the RKE transmitter twice to override the delay locking feature and immediately lock all of the doors. Press the TUNE/MENU knob when Delay Door Lock is highlighted to select On or Off. Press / BACK to return to the last menu.


Remote Lock/Unlock/Start Select Remote Lock/Unlock/Start and the following may be displayed (depending on the system): . Remote Lock Feedback . Remote Door Unlock . Remote Unlock Feedback


Remote Lock Feedback This allows selection of what type of feedback is given when locking the vehicle with the RKE transmitter. Press the TUNE/MENU knob when Remote Lock Feedback is highlighted. Turn the knob to select Lights and Horn, Lights Only, Horn Only, or Off. Press the TUNE/MENU knob to confirm and go back to the last menu.


Open Door Anti Lock Out When on, all doors will lock. The driver door will then unlock if door locking is requested while the driver door is open, and disable the Delay Door Lock feature. Even when this feature is off, the driver is protected from accidental lockouts when the key is in the ignition. If Off is selected, the Open Door Anti Lock Out feature may be enabled through an additional menu selection. Press the TUNE/MENU knob when Open Door Anti Lock Out is highlighted to select On or Off. Press / BACK to return to the last menu.


Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park).


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (36,1)


5-36


Instruments and Controls


Remote Door Unlock This allows selection of which doors will unlock when pressing K on the RKE transmitter. Press the TUNE/MENU knob when Remote Door Unlock is highlighted. Turn the knob to select All Doors or Driver Door Only. When set to Driver Door Only, the driver door will unlock the first time K is pressed and all doors will unlock when K is pressed a second time. When set to All Doors, all of the doors will unlock at the first press of K. Press the TUNE/MENU knob to confirm and go back to the last menu.


Remote Unlock Feedback If equipped, this allows selection of what type of feedback is given when unlocking the vehicle with the RKE transmitter. Press the TUNE/MENU knob when Remote Unlock Feedback is highlighted. Turn the knob to select Flash Lights or Off. Press the TUNE/MENU knob to confirm and go back to the last menu. Return to Factory Settings? Select Return to Factory Settings? to return all vehicle personalization to the default settings. Turn the knob to select Yes or No. Press the TUNE/MENU knob to confirm and go back to the last menu.


Universal Remote System See Radio Frequency Statement on page 13-15.


Universal Remote System Programming


If equipped, these buttons are in the overhead console. This system can replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices. These instructions refer to a garage door opener, but can be used for other devices.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (37,1)


Instruments and Controls


5-37


Do not use the Universal Remote system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. Read these instructions completely before programming the Universal Remote system. It may help to have another person assist with the programming process. Keep the original hand-held transmitter for use in other vehicles as well as for future programming. Erase the programming when vehicle ownership is terminated. See “Erasing Universal Remote System Buttons” later in this section. To program a garage door opener, park outside directly in line with and facing the garage door opener receiver. Clear all people and objects near the garage door.


Make sure the hand-held transmitter has a new battery for quick and accurate transmission of the radio-frequency signal. Programming the Universal Remote System For questions or help programming the Universal Remote system, call 1-800-355-3515 or see www.homelink.com. Programming involves time-sensitive actions, and may time out causing the procedure to be repeated. To program up to three devices: 1. Hold the end of the hand-held


transmitter about 3 to 8 cm (1 to 3 in) away from the Universal Remote system buttons with the indicator light in view. The hand-held transmitter was supplied by the manufacturer of the garage door opener receiver.


2. At the same time, press and


hold both the hand-held transmitter button and one of the three Universal Remote system buttons to be used to operate the garage door. Do not release either button until the indicator light changes from a slow to a rapid flash. Then release both buttons. Some garage door openers may require substitution of Step 2
with the procedure under “Radio Signals for Canada and Some Gate Operators” later in this section.


3. Press and hold the newly


programmed Universal Remote system button for five seconds while watching the indicator light and garage door activation.


If the indicator light stays on continuously or the garage door moves when the button is pressed, then


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (38,1)


5-38


Instruments and Controls


programming is complete. There is no need to complete Steps 4–6. If the indicator light does not come on or the garage door does not move, a second button press may be required. For a second time, press and hold the newly programmed button for five seconds. If the light stays on or the garage door moves, programming is complete. If the indicator light blinks rapidly for two seconds, then changes to a solid light and the garage door does not move, continue with programming Steps 4–6.


does not flash, press and hold the same button a second time for two seconds, then release it. Again, if the door does not move or the garage door lamp does not flash, press and hold the same button a third time for two seconds, then release it.


The Universal Remote system should now activate the garage door. Repeat the process for programming the two remaining buttons. Radio Signals for Canada and Some Gate Operators For questions or programming help call 1-800-355-3515 or see www.homelink.com. Canadian radio-frequency laws and some U.S. gate operators require transmitter signals to time out or quit after several seconds of transmission. This may not be long


Learn or Smart Button


4. After completing Steps 1–3 ,


locate the Learn or Smart button inside garage on the garage door opener receiver. The name and color of the button may vary by manufacturer.


5. Press and release the Learn or


6.


Smart button. Step 6 must be completed within 30 seconds of pressing this button. Inside the vehicle, press and hold the newly programmed Universal Remote system button for two seconds and then release it. If the garage door does not move or the lamp on the garage door opener receiver


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (39,1)


Instruments and Controls


5-39


enough for the Universal Remote system to pick up the signal during programming. If the programming did not work, replace Step 2 under “Programming the Universal Remote System” with the following: Press and hold the Universal Remote system button while pressing and releasing the hand-held transmitter button every two seconds until the signal has been successfully accepted by the Universal Remote system. The Universal Remote system indicator light will flash slowly at first and then rapidly. Proceed with Step 3 under “Programming the Universal Remote System” to complete.


Universal Remote System Operation


Using the Universal Remote System Press and hold the appropriate Universal Remote system button for at least one-half second. The indicator light will come on while the signal is being transmitted. Erasing Universal Remote System Buttons Erase all programmed buttons when vehicle ownership is terminated. To erase: 1. Press and hold the two outside buttons until the indicator light begins to flash. This should take about 10 seconds.


2. Release both buttons.


Reprogramming a Single Universal Remote System Button To reprogram any of the system buttons: 1. Press and hold any one of the


buttons. Do not release the button.


2. The indicator light will begin to flash after 20 seconds. Without releasing the button, proceed with Step 1 under “Programming the Universal Remote System.”


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (40,1)


5-40


Instruments and Controls


2 NOTES


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (1,1)


Lighting


6-1


; (Parking Lamps): Turns on the parking lamps including all lamps, except the headlamps. 5 (Headlamps): Turns on the headlamps together with the parking lamps and instrument panel lights. A warning chime sounds if the driver door is opened when the ignition switch is off and the headlamps are on. # (Front Fog Lamps): If equipped, press to turn the lamps on or off. See Front Fog Lamps on page 6-4. When the lights are on, ; will be lit. See Lamps On Reminder on page 5-22.


Lighting


Exterior Lighting


Exterior Lighting


Exterior Lamp Controls


Exterior Lamp Controls . . . . . . . . 6-1
Headlamp High/Low-Beam


Changer . . . . . . . . . . . . . . . . . . . . . 6-2
Flash-to-Pass . . . . . . . . . . . . . . . . . 6-2
Daytime Running


Lamps (DRL) . . . . . . . . . . . . . . . . 6-2


Automatic Headlamp


System . . . . . . . . . . . . . . . . . . . . . . 6-3
Hazard Warning Flashers . . . . . 6-3
Turn and Lane-Change


Signals . . . . . . . . . . . . . . . . . . . . . . 6-4
Front Fog Lamps . . . . . . . . . . . . . . 6-4


Interior Lighting


Instrument Panel Illumination


Control . . . . . . . . . . . . . . . . . . . . . . 6-5
Courtesy Lamps . . . . . . . . . . . . . . 6-5
Dome Lamps . . . . . . . . . . . . . . . . . 6-5
Reading Lamps . . . . . . . . . . . . . . . 6-5


Lighting Features


Entry Lighting . . . . . . . . . . . . . . . . . 6-6
Exit Lighting . . . . . . . . . . . . . . . . . . . 6-6
Battery Power Protection . . . . . . 6-7


The exterior lamp control is to the left of the steering column on the instrument panel. There are four positions: O (Off): Briefly turn to this position to turn the automatic lamp control off or on again. AUTO (Automatic): Turns the headlamps on automatically at normal brightness, together with the parking lamps, taillamps, license plate lamps, instrument panel lights, and sidemarker lamps.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (2,1)


6-2


Lighting


Headlamp High/ Low-Beam Changer


Flash-to-Pass To flash the high beams, pull the turn signal lever all the way toward you. Then release it.


3 (Headlamp High/Low-Beam Changer): Push the turn signal lever away from you and release to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.


This indicator light turns on in the instrument cluster when the high-beam headlamps are on.


Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles first sold in Canada. A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met: The ignition is in the ON/ RUN mode. The exterior lamp control is in AUTO. The engine is running.


When the DRL are on, only the low-beam headlamps, at a reduced level of brightness, will be on. The taillamps, sidemarker, instrument panel, and other lamps will not be on. The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps go off and the DRL come on. To turn the DRL off or on again, turn the exterior lamp control to O and then release. For vehicles first sold in Canada, the DRL cannot be turned off.


Buick Verano Owner Manual 6042574) - 2014 - crc - 10/18/13


(GMNA-Localizing-U.S./Canada/Mexico-


Black plate (3,1)


Automatic Headlamp System When it is dark enough outside and the exterior lamp control is in the automatic position, the headlamps come on automatically. See Exterior

Loading...
x