Download PDF Manual

The mirror can be calibrated by driving the vehicle in circles at 5 mph (8 km/h) or less until the display reads a direction. Mirrors equipped with OnStar® controls can be placed in calibration mode by pressing and holding the on/off button until a C is shown in the compass display.


2-37


Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance. If not adjusted to account for compass variance, your compass could give false readings. To adjust for compass variance, do the following: 1. Find your current location and variance zone


number on the following zone map.


2-38


2. Press and hold COMPASS (or the on/off button for


mirrors equipped with OnStar® controls) until a zone number appears in the display.


3. Once a zone number appears in the display, press


the COMPASS button (or the on/off button for mirrors equipped with OnStar® controls) quickly until the correct zone number appears in the display. Stop pressing the button and the mirror will return to normal operation. If C appears in the compass window, the compass may need calibration. See “Compass Calibration” explained previously.


Outside Power Mirrors


Your vehicle has power mirror controls located on the driver’s door armrest.


Press L or R on the selector switch located below the control pad to choose the left or right mirror. If you place the switch in the center position, no mirror movement will occur. To adjust a mirror, use the arrows located on the control pad to move the mirror in the direction you want it to go. Adjust each mirror so you can see some of the side of your vehicle and the area behind your vehicle. The mirrors may also have an arrow that flashes when the turn signal is used. See Turn Signal/Multifunction Lever on page 3-5. If your vehicle is equipped with the memory seat and mirrors feature, these mirror positions, along with the driver’s seat position can be stored in memory. See Memory Seat and Mirrors on page 2-51.


2-39


Outside Curb View Assist Mirror If you have the DIC feature, the passenger’s outside rearview mirror also includes a tilt-down feature that operates when the shift lever is in REVERSE (R). When the vehicle is shifted out of REVERSE (R), the passenger mirror will return to its original position after a five-second delay. This delay prevents movement of the mirror if multiple gear transitions (REVERSE (R) to DRIVE (D) to REVERSE (R)) occur during a parallel parking maneuver. This feature can be programmed on or off through the personal choice selection menu. See Driver Information Center (DIC) on page 3-47 or DIC Vehicle Personalization on page 3-51
for programming instructions.


Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat.


{CAUTION:


A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes.


2-40


Outside Automatic Dimming Heated Mirror If you have this feature, the driver’s side outside rearview mirror will adjust for the glare of headlamps behind you. This feature is controlled using the on and off settings on the automatic dimming rearview mirror. See “Automatic Dimming Rearview Mirror” or “Automatic Dimming Rearview Mirror with Compass” earlier in this section. If you have this feature, the left and right outside mirrors are also heated when you activate the rear window defogger. See “Rear Window Defogger” under Dual Automatic Climate Control System on page 3-24. Both outside mirrors can be folded forward or rearward. In the rearward position, they will fold flush with the vehicle. This feature is particularly useful in automatic car washes.


OnStar® System


Your vehicle may have this feature. OnStar® uses global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services. A complete OnStar® user’s guide and the terms and conditions of the OnStar® Subscription Service Agreement are included in your OnStar®-equipped vehicle’s glove box literature. For more information, visit www.onstar.com, contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827), or press the blue OnStar® button to speak to an OnStar® advisor 24 hours a day, 7 days a week. A completed Subscription Service Agreement is required prior to delivery of OnStar® services and prepaid calling minutes are also required for OnStar® Personal Calling and OnStar® Virtual Advisor use. Terms and conditions of the Subscription Service Agreement can be found at www.onstar.com.


2-41


Luxury and Leisure Plan (cid:127) All Directions and Connections Plan services (cid:127) Personal Concierge OnStar® Personal Calling With OnStar® Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts and no additional roaming charges. To find out more about OnStar® Personal Calling, refer to the OnStar® owner’s guide in your vehicle’s glove box, or call OnStar® at 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor With OnStar® Virtual Advisor you can listen to your favorite news, entertainment and information topics, such as traffic and weather reports, stock quotes and sports scores. You listen to your e-mail through your vehicle’s speakers, and reply with your hands on the wheel and your eyes on the road.


OnStar® Services One of the following plans is normally included for a specific duration with each vehicle equipped with OnStar®. You can upgrade or extend your OnStar® service plan to meet your needs. Safe and Sound Plan (cid:127) Automatic Notification of Air Bag Deployment (cid:127) Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock (cid:127) Remote Diagnostics (cid:127) Online Concierge Directions and Connections Plan (cid:127) All Safe and Sound Plan services (cid:127) Route Support (cid:127) RideAssist


Information and Convenience Services


2-42


(cid:127) HomeLink® Transmitter


HomeLink®, a combined universal transmitter and receiver, provides a way to replace up to three hand−held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting.


Additional HomeLink® information can be found on the internet at www.homelink.com or by calling 1-800-355-3515. If your vehicle is equipped with the HomeLink® transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.


This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes and modifications to this system by other than an authorized service facility could void authorization to use this equipment. Programming the HomeLink® Transmitter Do not use the HomeLink® Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow steps 6 through 8 to complete the programming of your HomeLink® Transmitter. Read the instructions completely before attempting to program the HomeLink® Transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter.


2-43


Keep the original transmitter for use in other vehicles as well as for future HomeLink® programming. It is also recommended that upon the sale of the vehicle, the programmed HomeLink® buttons should be erased for security purposes. Refer to “Erasing HomeLink® Buttons” or, for assistance, contact HomeLink® on the internet at: www.homelink.com or by calling 1-800-355-3515. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio frequency. Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons,


releasing only when the indicator light begins to flash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink® buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the HomeLink® buttons while keeping the indicator light in view.


3. Simultaneously press and hold both the desired


button on HomeLink® and the hand-held transmitter button. Do not release the buttons until Step 4
has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section.


4. The indicator light will flash slowly at first and then rapidly after HomeLink® successfully receives the frequency signal from the hand-held transmitter. Release both buttons.


5. Press and hold the newly-trained HomeLink® button


and observe the indicator light. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink® button is pressed and released. To program the remaining two HomeLink® buttons, begin with Step 2 under “Programming HomeLink®.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device (most commonly, a garage door opener).


2-44


6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit.


7. Firmly press and release the “Learn” or “Smart”


button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8.


8. Return to the vehicle. Firmly press and hold the programmed HomeLink® button for two seconds, then release. Repeat the press/hold/release sequence a second time, and depending on the brand of the garage door opener (or other rolling code device), repeat this sequence a third time to complete the programming. HomeLink® should now activate your rolling-code equipped device.


To program the remaining two HomeLink® buttons, begin with Step 2 of “Programming HomeLink®.” Do not repeat Step 1.


Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for HomeLink® to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out” in the same manner. If you live in Canada, or you are having difficulty programming a gate operator by using the “Programming HomeLink®” procedures (regardless of where you live), replace Step 3 under “Programming HomeLink®” with the following: Continue to press and hold the HomeLink® button while you press and release every two seconds (cycle) your hand-held transmitter until the frequency signal has been successfully accepted by HomeLink®. The indicator light will flash slowly at first and then rapidly. Proceed with Step 4 under “Programming HomeLink®” to complete.


2-45


Using HomeLink® Press and hold the appropriate HomeLink® button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing HomeLink® Buttons To erase programming from the three buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds.


2. Release both buttons. Do not hold for longer than


30 seconds.


HomeLink® is now in the train (learning) mode and can be programmed at any time beginning with Step 2
under “Programming HomeLink®.” Individual buttons can not be erased, but they can be reprogrammed. See “Reprogramming a Single HomeLink® Button” next.


2-46


Reprogramming a Single HomeLink® Button To program a device to HomeLink® using a HomeLink® button previously trained, follow these steps: 1. Press and hold the desired HomeLink® button.


Do not release the button.


2. The indicator light will begin to flash after


20 seconds. While still holding the HomeLink® button, proceed with Step 2 under “Programming HomeLink®.”


Resetting Defaults To reset HomeLink® to default settings do the following: 1. Hold down the two outside buttons for about


20 seconds until the indicator light begins to flash. 2. Continue to hold both buttons until the HomeLink®


indicator light turns off. 3. Release both buttons. For questions or comments, contact HomeLink® at 1-800-355-3515, or on the internet at www.homelink.com.


Storage Areas


Glove Box Use the key to lock and unlock the glove box. To open the glove box, pull the handle upward until the latch opens.


Garage Door Opener Compartment


To install your garage door opener, do the following: 1. Push the extended tab above the GARAGE button or insert a tool between the tab and outer edge of the cover. The garage door opener cover will flip down.


If your vehicle has this feature, the garage door opener storage area is located in the headliner near the front reading lamps.


2. Remove the square height adapters from the cover.


2-47


3. Place the height adapters on the proper peg by lining up the height adapters and the transmitter button on your garage door opener.


4. Use the hook and loop fastener found in the


storage area and attach the garage door opener securely inside the console. Line up the transmitter button with the height adapters.


5. Close the cover and test the GARAGE button. If your garage door opener doesn’t work after it is installed, try another combination.


2-48


Center Console Storage Area Your vehicle has a center console with two storage compartments and cupholders. The cupholders have removable liners to hold beverage containers of different sizes. To access the cupholders and the front storage area, push the doors covering them back into the console. In the front storage area you will find a place to store a cellular phone, as well as a built-in writing surface. Underneath this tray is a CD storage area and another door which can be opened to retrieve items which may fall into the space between the console and the sliding door. To access the CD storage area, place your finger in the oval in the top tray and lift up. To access the rear storage area, press the lift latch at the front edge of the armrest and pull up. Inside are areas which can be used to store a variety of items. The back of the console may contain either additional cupholders or air vents for the rear seat passengers. You will also find two accessory power outlets located inside the rear storage area. These outlets can be used for accessories requiring power, such as a cellular phone or fax machine. See Accessory Power Outlets on page 3-22.


Assist Handles An assist handle over each rear door and the front passenger’s door can be used to help passenger’s get in or out of your vehicle.


Rear Storage Area If your vehicle has this feature, the rear storage armrest contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback. This armrest also includes a storage area inside the armrest. To open it, pull up on the lever at the front edge of the armrest.


Rear Seat Armrest Your vehicle’s rear seat armrest contains two cupholders. To access the cupholders, pull the armrest down from the rear seatback.


Rear Seat Pass Through Your vehicle may be equipped with a rear storage armrest with a pass-through feature that allows for trunk access. Pull the rear armrest down, then push down on the trunk access panel latch to open the panel. To close, push the access panel until it latches.


Convenience Net Your vehicle may have a convenience net. You’ll see it just inside the back wall of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over during sharp turns or quick starts and stops. The net isn’t for larger, heavier loads. Store them in the trunk as far forward as you can. You can unhook the net so that it will lie flat when you’re not using it.


2-49


Sunroof Your vehicle may be equipped with a sunroof. The sunroof has both manual and express features for opening the glass panel and sunshade.


The switch for the sunroof is located on the headliner between the sun visors.


The sunroof switch has a number of positions that control sunroof movement. The switch will only work when the ignition is on or when the RAP is active. See “Retained Accessory Power (RAP)” under Ignition Positions on page 2-24.


2-50


Open: Press and hold the switch rearward to the first position to open the glass panel and sunshade. The sunshade can also be opened manually.


Comfort Stop: Press and release the switch rearward to the second position to express open the glass panel to the comfort stop position. The comfort stop position is designed to help reduce noise and make passengers more comfortable.


Express Open: When the glass panel is express opening, pressing the switch in any direction will stop it in a partially-opened position. The glass panel may be fully opened by pressing the switch rearward again. If you press and hold the switch in the express open position for more than one and a half seconds, the express open operation will be overridden and the sunroof will operate manually.


Close: To close the glass panel, press and hold the switch forward. As the glass panel reaches the closed position, it will open slightly toward the vent position and then drop down to the closed position to provide a better seal. The sunshade must be closed manually.


Vent: Once the sunroof is closed, it can be opened to the vent position by pushing the switch upward. To close the glass panel, pull the switch downward. The sunshade must be opened and closed manually for vent operation.


Vehicle Personalization Memory Seat and Mirrors


If your vehicle has this feature, the controls are located on the driver’s door panel, and are used to program and recall memory settings for the driver’s seating, outside mirror positions and climate controls. See Climate Controls Personalization on page 3-31 for more information.


To save your seat and mirror positions into memory, use the following procedure: 1. First identify the DRIVER # on the Driver Information


Center (DIC) by pressing the MEMORY button 1 or 2 or by pressing the unlock button on the remote keyless entry transmitter. See Driver Information Center (DIC) on page 3-47.


2. Adjust the driver’s seat and lumbar position to a


safe and comfortable driving position. Adjust both outside mirrors to suit you. See Outside Power Mirrors on page 2-39.


3. Press and hold the MEMORY button 1 or 2


corresponding with your DRIVER # displayed on the DIC for longer than three seconds. You will hear two beeps confirming that the seat and mirror positions have been entered into memory.


To set the seat and mirror positions for a second driver, follow the previous steps, but start by pressing the unlock button on the transmitter that displays the other DRIVER # on the DIC. Be sure to use the MEMORY button which corresponds to the DRIVER # identified by the second transmitter. To recall your memory positions, your vehicle must be in PARK (P). Push and release the MEMORY button 1 or 2
corresponding to the desired driving position. The seat and mirrors will move to the position previously stored for the identified driver. You will hear one beep.


2-51


To store the exit position for an easy exit, use the following procedure: 1. First identify the DRIVER # by pressing the


MEMORY button 1 or 2 or by pressing the unlock button on the transmitter.


2. Adjust the driver’s seat to the desired exit position. 3. Press and hold the EXIT button for longer than


three seconds. You will hear two beeps confirming that the seat exit position has been entered into memory.


To set the exit position for a second driver, follow the previous steps, but start by pressing the unlock button on the transmitter that displays the other DRIVER # on the DIC. Be sure to use the MEMORY button which corresponds to the DRIVER # identified by the other transmitter.


To recall the exit position, your vehicle must be in PARK (P). Push and release the EXIT button and the seat will move to the exit position previously stored for the currently identified driver. You will hear one beep. If an exit position has not been stored for the currently identified driver, the seat will move all the way back. To stop recall movement of the seat at any time, press the driver’s power seat control located on the outboard side of the front seat. Mirrors and lumbar positions will not be stored or recalled for the exit position. If you would like your stored driving or exit position to be recalled when unlocking your vehicle with the transmitter, see DIC Vehicle Personalization on page 3-51.


2-52


Section 3


Instrument Panel


Instrument Panel Overview ...............................3-2
Hazard Warning Flashers ................................3-4
Other Warning Devices ...................................3-4
Horn .............................................................3-5
Tilt Wheel .....................................................3-5
Turn Signal/Multifunction Lever .........................3-5
Exterior Lamps .............................................3-12
Interior Lamps ..............................................3-15
Head-Up Display (HUD) .................................3-18
Ultrasonic Rear Parking Assist (URPA) ............3-20
Accessory Power Outlets ...............................3-22
Ashtrays and Cigarette Lighter ........................3-23
Climate Controls ............................................3-24
Dual Automatic Climate Control System ...........3-24
Outlet Adjustment .........................................3-29
Passenger Compartment Air Filter ...................3-30
Steering Wheel Climate Controls .....................3-30
Climate Controls Personalization .....................3-31
Warning Lights, Gages and Indicators .............3-32
Instrument Panel Cluster ................................3-33
Speedometer and Odometer ...........................3-35
Tachometer .................................................3-35
Safety Belt Reminder Light .............................3-36
Air Bag Readiness Light ................................3-36
Battery Warning Light ....................................3-37
Brake System Warning Light ..........................3-38


Anti-Lock Brake System Warning Light .............3-39
Traction Control System (TCS) Warning Light ......3-39
Engine Coolant Temperature Gage ..................3-40
Malfunction Indicator Lamp .............................3-41
Oil Pressure Light .........................................3-44
Security Light ...............................................3-45
Cruise Control Light ......................................3-45
Service Vehicle Soon Light ............................3-45
Fuel Gage ...................................................3-46
Driver Information Center (DIC) .......................3-47
DIC Controls and Displays .............................3-47
DIC Warnings and Messages .........................3-50
DIC Vehicle Personalization ............................3-51
Audio System(s) .............................................3-57
Setting the Time ...........................................3-58
Radio with Cassette ......................................3-58
Radio with Cassette and CD ..........................3-63
Trunk-Mounted CD Changer ...........................3-71
Personal Choice Radio Controls ......................3-75
Theft-Deterrent Feature ..................................3-75
Audio Steering Wheel Controls .......................3-78
Understanding Radio Reception ......................3-78
Care of Your Cassette Tape Player .................3-79
Care of Your CDs .........................................3-80
Care of Your CD Player ................................3-80
Heated Backlite Antenna ................................3-80


3-1


Instrument Panel Overview


3-2


The main components of your instrument panel are the following:


A. Air Outlet. See Outlet Adjustment on page 3-29. B. Exterior Lamps Control. See Exterior Lamps


on page 3-12.


C. Turn Signal/Multifunction Lever. See Turn Signal/


Multifunction Lever on page 3-5.


D. Steering Wheel Controls (If Equipped). See Steering


Wheel Climate Controls on page 3-30 and Audio Steering Wheel Controls on page 3-78.


E. Hazard Warning Flashers Button. See Hazard


Warning Flashers on page 3-4.


F. Instrument Panel Cluster. See Instrument Panel


Cluster on page 3-33.


G. Shift Lever. See Automatic Transaxle Operation on


page 2-27.


H. Audio System. See Audio System(s) on page 3-57. I. Air Outlet. See Outlet Adjustment on page 3-29. J. Fuel Door Release Button. See Filling Your Tank on


page 5-6.


K. Trunk Release and Lockout Button. See “Remote


Trunk Release” and “Remote Trunk Release Lockout” under Trunk on page 2-15.


L. Hood Release. See Hood Release on page 5-10. M. Ignition Switch. See Ignition Positions on page 2-24. N. Traction Control Button (If Equipped). See Traction


Control System (TCS) on page 4-9.


O. Heated Seat Controls (Option). See Heated Seats


on page 1-3.


P. Ashtray and Cigarette Lighter. See Ashtrays and


Cigarette Lighter on page 3-23.


Q. Climate Control System. See Dual Automatic


Climate Control System on page 3-24.


R. Glove Box. See Glove Box on page 2-47. S. Passenger Climate Control (Option). See “Passenger


Temperature Control” under Dual Automatic Climate Control System on page 3-24.


3-3


Hazard Warning Flashers


The hazard warning flasher button is located on top of the steering column.


Your hazard warning flashers work no matter what position your key is in, and even if the key isn’t in. Press the button to make the front and rear turn signal lamps flash on and off. To turn off the flashers, press the button again. When the hazard warning flashers are on, your turn signals won’t work. Other Warning Devices If you carry reflective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle.


Your hazard warning flashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and off.


3-4


Horn Press on the center area of the steering wheel to sound the horn.


Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can also raise it to the highest level to give your legs more room when you exit and enter the vehicle. The lever that allows you to tilt the steering wheel is located on the left side of the steering column.


To tilt the wheel, hold the wheel and pull the lever toward you. Then move the steering wheel to a comfortable position and release the lever to lock the wheel in place.


Turn Signal/Multifunction Lever


The lever on the left side of the steering column includes the following:


Turn and Lane-Change Signals


(cid:127) Headlamp High/Low-Beam Changer


Flash-to-Pass


(cid:127) Windshield Wipers (cid:127) Windshield Washer (cid:127) Cruise Control For information on the exterior lamps, see Exterior Lamps on page 3-12.


3-5


(cid:127) (cid:127) Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.


An arrow on the instrument panel cluster will flash in the direction of the turn or lane change.


If your vehicle is equipped with the Head-Up Display (HUD), an arrow will also appear in the display area to indicate the direction of the turn or lane change. See Head-Up Display (HUD) on page 3-18 for more information. You may also have an arrow in the outside mirror that flashes when the turn signal is used. See Outside Power Mirrors on page 2-39 for more information.


To signal a lane change, just raise or lower the lever until the arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows flash at twice the normal rate, this may indicate that a signal bulb may be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check the fuse and check for burned-out bulbs. See Fuses and Circuit Breakers on page 5-99. If you have a trailer towing option with added wiring for the trailer lamps, the signal indicator will flash even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working. You do not need to add a different flasher. Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime will sound at each flash of the turn signal. To turn off the chime, move the turn signal lever to the off position.


3-6


Headlamp High/Low-Beam Changer To change the headlamps from low beam to high or high to low, pull the turn signal lever toward you, then release it.


When the high beams are on, a light on the instrument panel cluster will also be on. If your vehicle is equipped with HUD, this light will also appear in the display area.


Flash-To-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are off. To use it, pull the turn signal lever toward you, but not so far that you hear a click. If your headlamps are off or on low beam, your high-beam headlamps will turn on. They will stay on as long as you hold the lever toward you and the high-beam indicator on the instrument panel cluster will come on. Release the lever to turn the high-beam headlamps off.


Windshield Wipers The windshield wipers are controlled by turning the band marked WIPER.


OFF: Turn the band to OFF to turn the wipers off.


MIST: For a single wiping cycle, turn the band to MIST. Hold it there until the wipers start, then let go. The wipers will stop after one cycle. If you want more cycles, hold the band on MIST longer.


LO (Low Speed): Turn the band to LO for steady wiping at a slow speed.


HI (High Speed): Turn the band to HI for steady wiping at a high speed. The wiper speed may be set for a long or short delay between wipes. Turn the band to choose the delay time. The closer to LO, the shorter the delay. Heavy snow or ice can overload your wiper motor. A circuit breaker will stop the motor until it cools. Clear away snow or ice to prevent an overload. Keep in mind that damaged wiper blades may prevent you from seeing well enough to drive safely. To avoid damage, be sure to clear ice and snow from the wiper blades before using them. If your blades do become damaged, get new blades or blade inserts.


3-7


Rainsense™ II Wipers If your vehicle has this feature, the moisture sensor is mounted on the interior of the windshield below the rearview mirror and is used to automatically operate the wipers. This system operates by monitoring the amount of moisture build-up on the windshield. Wipes occur as needed to clear the windshield depending on the driving conditions and the sensitivity setting. In light rain or snow, fewer wipes will occur. In heavy rain or snow, wipes will occur more frequently. The system will operate in the delay, low speed and high speed modes. If the system is left on for long periods of time, occasional wipes may occur without any moisture on the windshield. This is normal and indicates that the Rainsense™ system is active. The Rainsense™ system is activated by turning the wiper control band to one of the five sensitivity levels within the delay area. The delay position closest to OFF/MIST is the lowest sensitivity setting, level one. This allows more rain or snow to collect on the windshield between wipes. You can increase the sensitivity of the system and the frequency of wipes by turning the wiper control band away from you to the


If you do not turn off the windshield wipers


higher sensitivity levels. The highest sensitivity setting, level five, is closest to the LO position. A single wipe will occur each time you turn the wiper control band to a higher sensitivity level to indicate that the sensitivity level has been increased. The windshield wipers also remain in a “high park” position (the wipers are stopped on the windshield and are not in the normal park position), even when the ignition is turned off. Notice: when driving through an automatic car wash, you could damage the wipers. Always turn off the windshield wipers before entering an automatic car wash. The MIST and wash cycles operate as normal and are not affected by the moisture-sensing function. The system can be overridden at any time by manually turning the wiper band to LO or HI speed. Notice: Do not place stickers or other items on the exterior glass surface directly in front of the moisture sensor. Doing this could cause the moisture sensor to malfunction.


3-8


Windshield Washer At the top of the multifunction lever there is a paddle with the word PUSH on it. For “programmed” operation, press and release the paddle. The washer will provide a measured amount of fluid to the windshield and the wiper will either stop or return to your original wiping speed. For “demand” operation, press and hold the paddle for at least two seconds. Release the paddle when you have enough fluid and the wipers will either stop or return to your original wiping speed.


{CAUTION:


In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.


If your vehicle is equipped with a DIC, a WINDSHIELD WASHER FLUID LOW message will appear on the instrument panel cluster when the vehicle is low on washer fluid. See DIC Warnings and Messages on page 3-50.


Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, the cruise control shuts off.


{CAUTION:


(cid:127) Cruise control can be dangerous where


you can not drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic.


(cid:127) Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel spinning, and you could lose control. Do not use cruise control on slippery roads.


3-9


If your vehicle is in cruise control when the optional traction control system begins to limit wheel spin, the cruise control will automatically disengage. See Traction Control System (TCS) on page 4-9. When road conditions allow you to safely use it again, you may turn the cruise control back on. Setting Cruise Control


{CAUTION:


If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.


1. Move the cruise control


switch to ON.


2. Get up to the speed you want. 3. Push in the SET button at the end of the turn signal


lever and release it. The CRUISE light on the instrument panel cluster will come on.


4. Take your foot off the accelerator pedal.


3-10


Resuming a Set Speed Setting the cruise control at a desired speed and then applying the brake will end the cruise control function. Once you are going about 25 mph (40 km/h) or more, you can move the cruise control switch from ON to R/A (Resume/Accelerate) briefly to reset. This returns you to your desired preset speed. Remember, if you hold the switch at R/A, the vehicle will accelerate until you release the switch or apply the brake. So unless you want to go faster, do not hold the switch at R/A. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to go to a higher speed. Push the SET button at the end of the lever, then release the button and the accelerator pedal. You will now cruise at the higher speed.


(cid:127) Move the cruise switch from ON to R/A. Hold it there until you reach a desired speed and then release the switch. To increase your speed in very small amounts, briefly move the switch to R/A, then release it.


Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster. The accelerate feature will only work after you have set the cruise control speed by pushing the SET button. Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: (cid:127) Push in the SET button at the end of the lever until


you reach a desired lower speed, then release it. To slow down in very small amounts, push the button briefly. Each time you do this, you will go about 1 mph (1 6 km/h) slower.


Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier.


3-11


(cid:127) Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers find this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control There are two ways to turn off the cruise control: (cid:127) Step lightly on the brake pedal. (cid:127) Move the cruise switch to OFF. The CRUISE light


will also go out.


Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased.


3-12


Exterior Lamps


This control, located to the left of the steering column, operates the following systems:


(cid:127) Headlamps


Taillamps


(cid:127) Parking Lamps License Lamps


(cid:127) Sidemarker Lamps


Instrument Panel Lights Interior Courtesy Lamps


(cid:127) (cid:127) (cid:127) (cid:127) OFF: Pushing the exterior lamps control all the way in turns off all lamps and lights.


Parking Lamps: Pulling the exterior lamps control out to the first position turns on the parking lamps, license plate lamps, the sidemarker lamps and the instrument panel lights.


Headlamps: Pulling the exterior lamps control out to the second position turns on the headlamps, together with the previously listed lamps and lights. For information on the interior lights, see Interior Lamps on page 3-15. Headlamps On Reminder If you leave the exterior lamp control on, remove the key from the ignition and open the driver’s door, you will hear a continuous warning chime. The chime will turn off when the lamps are turned off.


Daytime Running Lamps Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles first sold in Canada. A light sensor on top of the instrument panel monitors the exterior light level for the operation of DRL and Twilight Sentinel®, so be sure it is not covered. The DRL system will make your high-beam headlamps come on at reduced brightness in daylight when the following conditions are met:


The ignition is on. The exterior lamps control is off. The transaxle is not in PARK (P).


When DRL are on, only your high-beam headlamps will be on. The parking lamps, taillamps, sidemarker and other lamps will not be on. Your instrument panel will not be lit up either.


3-13


(cid:127) (cid:127) (cid:127) When it is dark enough outside, your high-beam headlamps will change to low-beam headlamps at full brightness. The other lamps that turn on with your headlamps will also turn on. When it is bright enough outside, the regular lamps will turn off, and your high-beam headlamps change to the reduced brightness of DRL. To idle your vehicle with the DRL off, shift the transaxle into PARK (P). The DRL will stay off until you shift out of PARK (P). To turn off all exterior lighting at night when you are parked, turn off the exterior lamp control and slide the Twilight Sentinel® control all the way to the left. When released, the control will return to the Twilight Sentinel® minimum delay position and the lights will turn off. As with any vehicle, you should turn on the regular headlamp system when you need it. Cornering Lamps The cornering lamps come on when the headlamps or parking lamps are on and you signal a turn with the multifunction lever. They provide more light for cornering.


3-14


Twilight Sentinel®


Twilight Sentinel® turns your headlamps on and off by sensing how dark it is outside.


To operate this feature, slide the control to any position to vary the lamp time-out. You can set the delay time from only a few seconds to three minutes. If you move the control all the way to MAX, your lamps will remain on for three minutes after you turn off your engine. If you move the control almost all the way in the other direction, so it is just on, the lamps will go off quickly when you turn off your engine. Sliding the control to OFF, turns off the Twilight Sentinel® feature. Light Sensor Your Twilight Sentinel® and DRL work with the light sensor on top of the instrument panel. Do not cover it up. If you do, it will sense “dark” and the headlamps will come on.


Interior Lamps Instrument Panel Brightness Adjust the instrument panel light brightness by turning the exterior lamps control. Courtesy Lamps When any door is opened, several lamps go on. They make it easy for you to enter and leave your vehicle. You can also turn these lamps on by turning the exterior lamps control clockwise all the way past the normal stop. Entry Lighting When you open either front door or press the unlock button on the remote keyless entry transmitter, the lamps inside your vehicle will turn on. These lamps will turn off after about 40 seconds. These lamps will also turn off if you start the engine or activate the power door locks. Delayed Entry Lighting When you open the door, the interior lamps will come on. When you close the door with the ignition off, the interior lamps will stay on for 25 seconds or until the ignition is turned to an on position. Locking the doors with the


power door lock switch will override the delayed entry lighting feature and the lamps will turn off right away. Using the remote keyless entry transmitter to lock the door will not cancel delayed lighting. Theater Dimming This feature allows for a three to five-second fade out of the courtesy lamps instead of immediate turn off. Delayed Exit Lighting With this feature, the interior lamps will come on for 25 seconds after you remove the key from the ignition. This will give you time to find the door handle or lock switches. Parade Dimming This feature prohibits the dimming of your instrument panel displays during daylight while your headlamps are on. This feature operates with the light sensor for the Twilight Sentinel® and is fully automatic. When the light sensor reads darkness outside, you will be able to dim your instrument panel displays once again.


3-15


To turn the feature on do the following: 1. Press and hold LOCK on the driver’s door lock switch throughout this procedure. All doors will lock.


2. Press the remote alarm button on the transmitter to


enter the programming mode. Perimeter lighting remains off at this time and the horn will chirp one time.


3. Press the remote alarm button on the transmitter again. Perimeter lighting is now enabled and the horn will chirp two times.


4. Release the door lock switch. The perimeter lighting


feature is now on.


Perimeter lighting can also be activated through the DIC. See DIC Vehicle Personalization on page 3-51
or Driver Information Center (DIC) on page 3-47.


Perimeter Lighting When the unlock button on the remote keyless entry transmitter is pressed, the DRL, parking lamps and back-up lamps will come on if it is dark enough outside. This feature will only be activated when the security feedback feature is programmed to be in Modes 1, 3
or 5 on the transmitter. Modes 0, 2 and 4 do not respond with exterior lights flashing when unlocking the vehicle so perimeter lighting will not be active. This feature can be programmed on or off for each transmitter. To turn the feature off do the following: 1. Press and hold LOCK on the driver’s door lock switch


throughout this procedure. All doors will lock.


2. Press the remote alarm button on the transmitter to


enter the programming mode. Perimeter lighting remains on at this time and the horn will chirp two times.


3. Press the remote alarm button on the transmitter again. Perimeter lighting is disabled and the horn will chirp one time.


4. Release the door lock switch. The perimeter lighting


feature is now off.


3-16


Front Reading Lamps


Rear Reading Lamps


The front reading lamps, located on the headliner, and the interior courtesy lamps will come on when you open a door. They will turn off when you turn on the ignition. To turn on the front reading lamps when the doors are closed, press the button behind the lamp you want to turn on. Press it again to turn the lamp off. These lamps work even when the ignition is off.


To turn on a rear reading lamp, press the button above that rear door. To turn off the reading lamp, press the button again. Trunk Lamp When you open the trunk to its full open position, a lamp will come on inside the trunk. This lamp will automatically turn off when the trunk is closed.


3-17


The information may be displayed in English or metric units and appears as a reflection in the windshield. The HUD consists of the following information: (cid:127) Speedometer Reading Turn Signal Indicators


(cid:127) High-Beam Headlamp Indicator (cid:127) CHECK GAGES Message


Glove Box Lamp When you open the glove box, a lamp will come on inside the glove box. This will automatically turn off when the glove box is closed. Battery Rundown Protection This feature shuts off all lamps that are left on for more than 10 minutes when the ignition is off. This will keep your battery from running down.


Head-Up Display (HUD)


{CAUTION:


If the HUD image is too bright, or too high in your field of view, it may take you more time to see things you need to see when it is dark outside. Be sure to keep the HUD image dim and placed low in your field of view.


If your vehicle is equipped with the Head-Up Display (HUD), you can see some of the driver information that appears on your instrument panel cluster.


The HUD shows these images when they are lighted on the instrument panel cluster.


3-18


(cid:127) Be sure to continue scanning your displays, controls and driving environment just as you would in a vehicle without HUD. If you never look at your instrument panel, you may not see something important, such as a warning light. Notice: parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid.


If you try to use the HUD image as a


The HUD controls are located in the overhead console.


1. Start your engine and slide the HUD dimmer switch


all the way up. The brightness of the HUD image is determined by whether the headlamps are on or off, and where you have the HUD dimmer switch set.


2. Adjust the seat to a comfortable driving position. Keep pressing the top arrow on the image height adjuster to raise the image as far as possible. 3. Keep pressing the bottom arrow on the image


height adjuster to move the image as low as possible, while still keeping it in full view.


4. Slide the dimmer switch downward until the HUD


image is no brighter than necessary.


To turn the HUD display off, slide the dimmer switch all the way down. If the sun comes out, the sky becomes cloudy, or if you turn your headlamps on, you may need to adjust the HUD brightness using the dimmer switch. Polarized sunglasses could make the HUD image harder to see. To change the display from English to metric units, push the ENG/MET button located to the left of the steering column.


3-19


Care of the HUD Clean the inside of the windshield as necessary to remove any dirt or film that reduces the sharpness or clarity of the HUD image. To clean the HUD lens, spray household glass cleaner on a soft, clean cloth. Gently wipe and dry the HUD lens. Do not spray cleaner directly on the lens to avoid cleaner leaking inside the unit. If You Can’t See The HUD Image When the Ignition is On If the ignition is on and you can’t see the HUD image, check to see if:


The headlamps are on.


(cid:127) Something is covering the HUD unit.


The HUD dimmer control is adjusted properly. The HUD image is adjusted to the proper height.


(cid:127) A fuse is blown. See Fuses and Circuit Breakers on


page 5-99.


Keep in mind that your windshield is part of the HUD system. If you ever have to have your windshield replaced, be sure to get one that is designed for HUD or your HUD image may look blurred or out of focus.


3-20


Ultrasonic Rear Parking Assist (URPA) Your vehicle may be equipped with Ultrasonic Rear Parking Assist (URPA). URPA is designed to help you park while in REVERSE (R) and operates only at speeds less than 3 mph (5 km/h). URPA can help you avoid colliding with objects such as parked vehicles. The system can detect objects 5 feet (1.5 m) behind your vehicle and tell you how close those objects are to your rear bumper. The URPA display is located inside the vehicle, above the rear window. It has three color-coded lights that can be seen through the rearview mirror.


{CAUTION:


Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while


CAUTION:


(Continued)


(cid:127) (cid:127) (cid:127) CAUTION:


(Continued)


parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle. So, unless you check carefully behind you before and when you back up, you could strike children, pedestrians, bicyclists or pets behind you, and they could be injured or killed. Whether or not you are using Rear Park Assist, always check carefully behind your vehicle before you back up and then watch closely as you do.


How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R). When the system comes on, the three lights on the display will briefly illuminate to let you know that the system is working. If your vehicle is moving in REVERSE (R) at a speed greater than 3 mph (5 km/h), the red light will flash to remind you the system does not work at this speed. The first time an object is detected while in REVERSE (R), a chime will sound and the following will occur in sequence, depending on the distance from the object: (cid:127) At 5 feet (1.5 m) a chime will sound and one amber


light will be lit.


(cid:127) At 40 inches (1.0 m) both amber lights will be lit. (cid:127) At 20 inches (0.5 m) a continuous chime will sound


and all three lights (amber/amber/red) will be lit.


(cid:127) At 1 foot (0.3 m) a continuous chime will sound and


all three lights (amber/amber/red) will flash.


URPA can detect objects 3 inches (7.6 cm) and wider, and at least 10 inches (25.4 cm) tall, but it cannot detect objects that are above trunk level. In order for the rear sensors to recognize an object, it must be within operating range.


3-21


If the URPA system is not functioning properly, the display will flash red, indicating that there is a problem. The light will also flash red while driving if a trailer is attached to your vehicle, or a bicycle or object is on the back of, or hanging out of your trunk. The light will continue to flash until the trailer or the object is removed and your vehicle is driven forward at at least 15 mph (25 km/h). It may also flash red if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush or materials such as paint or the system may not work properly. If after cleaning the rear bumper and driving forward at at least 15 mph (25 km/h), the display continues to flash red, see your dealer. For cleaning instructions, see Cleaning the Outside of Your Vehicle on page 5-93. It may also flash red if your vehicle is moving in REVERSE (R) at a speed greater than 3 mph (5 km/h). Other conditions that may affect system performance include things like the vibrations from a jackhammer or the compression of airbrakes on a very large truck. As always, drivers should use care when backing up a vehicle. Always look behind you, being sure to check for other vehicles, obstructions and blind spots.


Accessory Power Outlets The accessory power outlets can be used to plug in electrical equipment such as a cellular telephone or CB radio. Your vehicle has two power outlets located in the rear storage area of the front center console. See Center Console Storage Area on page 2-48 for more information on location. Your vehicle may have a small cap that must be pulled down to access the accessory power outlet. If it does, when not using the outlet be sure to cover it with the protective cap. The accessory power outlets will only operate while the ignition key is in RUN and for 10 minutes after turning the ignition off. If you would like to operate an accessory for an extended period of time, contact your dealer for more information. Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating.


3-22


Certain electrical accessories may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem see your dealer for additional information on accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only.


Improper use of the power outlet can cause


Ashtrays and Cigarette Lighter The front ashtray is located under the climate control panel on the center console. Press on the door to release the ashtray. To close, press on the door again. To empty the ashtray, remove it from the center console by gripping the edges and pulling straight out. To reinstall, push the tray back into place. The rear ashtrays are located on each rear door panel. To remove a rear ashtray, open the lid and ease the ashtray upward until the edge can be grasped to pull the ashtray up and out. Notice: in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle. Never put flammable items in the ashtray. There is a cigarette lighter near the front ashtray. To use it, push it in all the way and let go. When it’s ready, it will pop back out by itself. Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.


If you put papers or other flammable items


3-23


Climate Controls


Dual Automatic Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle.


Automatic Operation


AUTO (Automatic): Press the AUTO button for automatic control of the inside temperature, the air delivery mode and the fan speed.


3-24


1. Press the AUTO button. 2. Adjust the temperature to 75° F (24° C).


Choosing the coldest or warmest temperature setting will not cause the system to heat or cool any faster. If you set the system at the warmest temperature setting, the system will remain in manual mode at that temperature and it will not go into automatic mode. In cold weather, the system will start at reduced fan speeds to avoid blowing cold air into your vehicle until warmer air is available. The system will start out blowing air at the floor but may change modes automatically as the vehicle warms up to maintain the chosen temperature setting. The length of time needed for warm up will depend on the outside temperature and the length of time that has elapsed since your vehicle was last driven.


3. Wait for the system to regulate. This may take from


10 to 30 minutes. Then adjust the temperature, if necessary.


Do not cover the solar sensor located in the center of the instrument panel, near the windshield. For more information on the solar sensor, see “Sensors” later in this section.


Manual Operation Pressing the FAN or AIR FLOW buttons cancels automatic operation and places the system in manual mode. Press the AUTO button to return to automatic operation.


TEMP (Temperature): To manually adjust the temperature inside the vehicle, push the TEMP arrow. Push the TEMP up arrow for warmer temperature settings and the TEMP down arrow for cooler temperature settings. The setting will be shown on the display. The display will return to the outside temperature after a few seconds. 9 FAN: Pressing the FAN button will display and hold the current fan speed while in manual mode. If you want the fan to run at a lower speed, push the down arrow on the FAN button. If you want to increase the fan speed, push the up arrow on the FAN button. The fan indicators will also be shown on the display.


If the airflow seems low when the fan is at the highest setting, the passenger compartment air filter may need to be replaced. For more information, see Passenger Compartment Air Filter on page 3-30.


AIR FLOW: Pressing the AIR FLOW button will display and hold the current setting while in manual mode. Use the up and down arrows on the AIR FLOW button to cycle through the available modes. (cid:127) WINDSHIELD-FLOOR: This mode directs most of


the airflow to the windshield with some airflow to the outboard outlets (for the side windows) and the floor outlets.


(cid:127) MID: This mode directs airflow through the


instrument panel outlets. FLOOR-MID: This mode directs airflow through both the floor and the instrument panel outlets. There is also a small amount of air directed to the windshield and the outboard outlets (for the side windows). FLOOR: This mode directs most of the airflow to the floor outlets with some directed to the outboard outlets (for the side windows) and the windshield.


OFF: Press the OFF button once to turn off the passenger climate control, if it has been activated. Pressing the OFF button a second time will turn off the main system. The outside temperature will be shown on the display when the system is off.


3-25


(cid:127) (cid:127) VENT: Pressing the VENT button allows outside air to flow through your vehicle without the air conditioning compressor working. To turn off the VENT selection, push the VENT button again.


Using these settings together for long periods of time may cause the air inside of your vehicle to become too dry. To prevent this from happening, after the air in your vehicle has cooled, turn the recirculation mode off.


The air conditioning system removes moisture from the air, so you may sometimes notice a small amount of water dripping underneath your vehicle while idling or after turning off the engine. This is normal. Sensors The solar sensor on your vehicle monitors the solar radiation and the air inside of your vehicle, then uses the information to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed and the air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun. The recirculation mode will also be activated, as necessary. Do not cover the solar sensor located in the center of the instrument panel, near the windshield, or the system will not work properly.


Selecting the VENT and AUTO buttons at the same time allows the system to control the airflow automatically without using the air conditioning compressor or the recirculation mode.


RECIRC (Recirculation): Press this button to limit the amount of outside air coming into the vehicle. It can be used to prevent outside air and odors from entering your vehicle or to help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. When the button is pressed, an indicator light will come on. The recirculation mode cannot be used with the FRONT defrost or VENT mode.


On hot days, open the windows to let hot air escape; then close them. This helps to reduce the time it takes for your vehicle to cool down. It also helps the system to operate more efficiently.


For quick cool down on hot days, press the AUTO button and the system will automatically enter recirculation mode and the temperature will be at the full cold position for maximum cooling.


3-26


Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. 1 FRONT: Press the FRONT button to defrost the windshield by directing airflow toward the windshield and outboard outlets (for the side windows). To turn off FRONT, press the AUTO or AIR FLOW buttons.


If the AIR FLOW up button is pressed while in the FRONT defrost mode, the system will direct the air toward the instrument panel outlets. If the AIR FLOW down button is pressed while in the FRONT defrost mode, the system will direct the air toward the floor, and the FRONT defrost mode will cancel. Do not drive the vehicle until all the windows are clear.


Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. = REAR: Press this button to turn the rear window defogger on or off. Be sure to clear as much snow from the rear window as possible.


At speeds above 30 mph (48 km/h), the defogger will operate continuously until you press the REAR button again. After 10 minutes of driving below 30 mph (48 km/h), the defogger will turn off automatically. If you need additional warming time, push the button again. The system will then operate for five minutes before going off by itself.


If your vehicle has heated outside rearview mirrors, the mirrors will heat to help clear fog or frost from the surface of the mirror when the rear window defogger button is pressed. Notice: Using a razor blade or sharp object to clear the inside rear window may damage the rear window defogger. Repairs would not be covered by your warranty. Do not clear the inside of the rear window with sharp objects.


3-27


Passenger Temperature Control If your vehicle has the optional separate passenger’s temperature control, then the driver and the right front passenger can select separate temperature settings. This feature allows the front passenger to select a temperature that is 5° F (3° C) warmer or cooler than the driver’s selected temperature.


Slide the lever toward WARM for warmer air or toward COOL for cooler air. Press OFF on the main climate control system once to turn off the passenger’s temperature control. When this lever is moved, the current inside temperature will appear on the display for a few seconds, then the outside temperature will appear.


The lever for this feature is located on the right side of the instrument panel.


3-28


Outlet Adjustment


Operation Tips (cid:127) Clear away any ice, snow or leaves from the air


inlets at the base of the windshield that may block the flow of air into your vehicle.


(cid:127) Use of non-GM approved hood deflectors may adversely affect the performance of the system.


(cid:127) Keep the path under the front seats clear of objects to help circulate the air inside of your vehicle more effectively. If the airflow seems low when the fan is at the highest setting, the passenger compartment air filter may need to be replaced. See Passenger Compartment Air Filter on page 3-30.


Use the thumbwheel located in the middle of the front outlets to change the direction of the airflow and to open and close the outlets.


Use the thumbwheel located between the rear passenger outlets to open and close the outlets. Adjust the direction of the airflow from side to side with the levers in the center of each rear outlet.


3-29


(cid:127) Passenger Compartment Air Filter Passenger compartment air, both outside air and recirculated air, is routed through a passenger compartment filter, which is part of a three piece filter system. The filter removes certain particles from the air, including pollen and dust particles. Reductions in airflow, which may occur more quickly in dusty areas, indicate that the filter needs to be replaced early.


The filter should be replaced as part of routine scheduled maintenance. See Part A: Scheduled Maintenance Services on page 6-4 for replacement intervals. See your dealer for details on changing the filter. Once you remove your filter, if you choose not to replace it, it will not damage your vehicle. However, the air will no longer be filtered.


Steering Wheel Climate Controls


If your vehicle has this feature, you can control the temperature function by using the switch located on your steering wheel.


The particle filter is located inside of the air control module. The air control module is located behind an access panel near the accelerator pedal.


w TEMP x (Temperature): Press the up or down arrow on this switch to increase or decrease the temperature.


3-30


Climate Controls Personalization If your vehicle is equipped with this feature, up to two drivers are able to store and recall climate control settings for the temperature, the fan speed and the direction of the airflow. Memory buttons 1 and 2 are located on the driver’s door panel and correspond to the numbers 1 or 2 found on the back of each remote keyless entry transmitter. To store settings, do the following: 1. Select the desired temperature, fan speed and


airflow mode. If desired, a separate temperature setting may also be selected for the front seat passenger. For information on how to do this, see Dual Automatic Climate Control System on page 3-24.


2. Locate memory buttons 1 and 2 on the driver’s


door panel.


3. Press the memory button on the door panel that


corresponds to the number on the back of the transmitter you are programming, until you hear two beeps. The beeps confirm that your selection has been saved and can now be recalled. For more information on the memory feature, see Memory Seat and Mirrors on page 2-51.


Follow these steps each time you want to change the stored settings. To recall the climate control settings last stored on your transmitter, press the unlock button on your remote keyless entry transmitter and put the ignition in ACCESSORY or RUN. The settings will be recalled.


3-31


Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on briefly when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens.


Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly — and even dangerous. So please get to know your warning lights and gages. They are a big help. Your vehicle may also have a DIC that works along with the warning lights and gages. See Driver Information Center (DIC) on page 3-47.


3-32


Instrument Panel Cluster Your vehicle is equipped with one of the following instrument panel clusters. Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. It includes indicator warning lights and gages that are explained on the following pages. Be sure to read about those that apply to the instrument panel cluster for your vehicle.


Base Cluster, Uplevel Similar (United States version shown, Canada similar)


3-33


Cluster with Driver Information Center (DIC) (United States version shown, Canada similar)


3-34


Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper-resistant odometer. You may wonder what happens if your vehicle needs a new odometer installed. If possible, the new one has to be set to the same reading the old one had. If it can’t be, then it’s set at zero and a label must be put on the driver’s door to show the old mileage reading and when the new odometer was installed. Trip Odometer A trip odometer can tell how far you’ve driven since you last set it back to zero. To reset it, push the RESET button. The trip odometer is reset through the Driver Information Center (DIC) if your vehicle is equipped with this feature. See DIC Controls and Displays on page 3-47 for more information.


Tachometer


The tachometer tells you how fast the engine is running. It displays engine speed in thousands of revolutions per minute (rpm).


If you operate the engine with the


Notice: tachometer in the shaded warning area, your vehicle could be damaged, and the damages would not be covered by your warranty. Do not operate the engine with the tachometer in the shaded warning area.


3-35


Safety Belt Reminder Light When the key is turned to RUN, a chime will come on for several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is already buckled.


The safety belt light will also come on and stay on for several seconds, then it will flash for several more.


If the driver’s belt is already buckled, neither the chime nor the light will come on.


Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows AIR BAG. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensors, the air bag modules, the wiring and the crash sensing and diagnostic module. For more information on the air bag system, see Air Bag Systems on page 1-49.


This light will come on when you start your vehicle, and it will flash for a few seconds. Then the light should go out. This means the system is ready.


If the air bag readiness light stays on after you start the vehicle or comes on when you are driving, your air bag system may not work properly. Have your vehicle serviced right away.


3-36


{CAUTION:


If the air bag readiness light stays on after you start your vehicle, it means the air bag system may not be working properly. The air bags in your vehicle may not inflate in a crash, or they could even inflate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the air bag readiness light stays on after you start your vehicle.


The air bag readiness light should flash for a few seconds when you turn the ignition key to RUN. If the light doesn’t come on then, have it fixed so it will be ready to warn you if there is a problem.


Battery Warning Light


When you turn the key to RUN, this light will come on briefly, to show the battery charging system is working.


When the light goes off and stays off, the charging system is working. If the light stays on, a chime will sound indicating you need service, and you should take your vehicle to the dealer at once. To save your battery until you get there, turn off all accessories and turn off your climate control system.


3-37


If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 4-31.


{CAUTION:


Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service.


Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away.


This light should come on when you turn the key to RUN. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem.


When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If you try to drive off with the parking brake set, a chime will also come on until you release the parking brake. If the light stays on after your parking brake is fully released, it means you have a brake problem.


3-38


Anti-Lock Brake System Warning Light


Traction Control System (TCS) Warning Light


With the anti-lock brake system, the light(s) will come on when your engine is started and may stay on for several seconds. That’s normal.


If your vehicle has this feature, this warning light should come on briefly when the engine is started.


If the warning light doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem. If it stays on, or comes on when you’re driving, there may be a problem with your traction control system and your vehicle may need service. When this warning light is on, the system will not limit wheel spin. Adjust your driving accordingly.


If the light stays on and the chime sounds, turn the ignition to OFF. Or, if the light comes on and the chime sounds when you’re driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on and the chime sounds, or the light comes on again while you’re driving, your vehicle needs service. If the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes. If the regular brake system warning light is also on, you don’t have anti-lock brakes and there’s a problem with your regular brakes. See Brake System Warning Light on page 3-38. The anti-lock brake system warning light will come on briefly when you turn the ignition key to RUN. This is normal. If the light doesn’t come on then, have it fixed so it will be ready to warn you if there is a problem.


3-39


The traction control system warning light may come on for the following reasons:


Engine Coolant Temperature Gage


If you turn the system off by pressing the button located on the end of the shift lever, the warning light will come on and stay on. To turn the system back on, press the button again. The warning light should go off. See Traction Control System (TCS) on page 4-9 for more information. If there’s a brake system problem that is specifically related to traction control, the traction control system will turn off, the warning light will come on and the chime will sound. If the traction control system is affected by an engine-related problem, the system will turn off, the warning light will come on and the chime will sound.


If the traction control system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service.


This gage measures the temperature of the vehicle’s engine. If the pointer moves into the shaded area, the engine is too hot. A temperature indicator light will turn on and a chime will sound.


If you have been operating your vehicle under normal driving conditions, and the temperature indicator light comes on, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.


3-40


(cid:127) (cid:127) (cid:127) Malfunction Indicator Lamp Service Engine Soon Light


Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems.


This system is called OBD II (On-Board Diagnostics- Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The SERVICE ENGINE SOON light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. Notice: light on, after a while, your emission controls may not work as well, your fuel economy may not


If you keep driving your vehicle with this


be as good and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modifications made to the engine, transaxle, exhaust, intake or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modifications to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways:


Light Flashing — A misfire condition has been detected. A misfire increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required.


3-41


(cid:127) (cid:127) If the Light Is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed. (cid:127) Avoiding hard accelerations. (cid:127) Avoiding steep uphill grades.


If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops flashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still flashing, follow the previous steps and see your dealer for service as soon as possible.


If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-6. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off.


3-42


(cid:127) Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-4. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that may have developed.


Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know in order to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the SERVICE ENGINE SOON light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your GM dealer can prepare the vehicle for inspection.


3-43


Oil Pressure Light


This light tells you if there could be a problem with your vehicle’s engine oil pressure.


The oil pressure light will come on briefly when you turn your key to RUN. It goes off once you turn the key to START. That’s just a check to be sure the light works. This is normal and doesn’t show a problem. If it doesn’t come on and then go off, be sure to have it fixed so it will be there to warn you if there is a problem. When this light comes on and stays on, and a chime sounds, it means oil isn’t going through the engine properly. The oil could be low, or there might be some other oil problem. See your dealer for service.


{CAUTION:


Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.


Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil.


3-44


Security Light


Service Vehicle Soon Light


This light will come on if your vehicle has certain non-emission related problems.


United States


Canada


Your vehicle is equipped with a content theft-deterrent alarm system. With this system, the SECURITY light will flash as you open the door if your ignition is off. For more information see Content Theft-Deterrent on page 2-19. Cruise Control Light


The CRUISE light comes on when you set the vehicle’s cruise control.


For example, if the entire electrical system fails to send and receive messages from the vehicle’s components, the SERVICE VEHICLE SOON warning light comes on. These problems may not be obvious and may affect vehicle performance or durability. Consult a qualified dealership for necessary repairs to maintain top vehicle performance. This light will come on briefly when the ignition is turned on to show that it is working properly.


Loading...
x