2007 Buick Lacrosse Owners Manual

Download PDF Manual
The airbag system does not need regular maintenance. 80 Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to the front or sides of the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly. Also, the airbag system may not work properly if you relocate any of the airbag sensors. If you have any questions about this, you should contact Customer Assistance before you modify your vehicle. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 478. Q: Because I have a disability, I have to get my vehicle modiﬁed. How can I ﬁnd out whether this will affect my airbag system? A: Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module, steering wheel, instrument panel, ceiling headliner, ceiling and pillar garnish trim, roof-mounted airbag modules, or airbag wiring can affect the operation of the airbag system. If you have questions, call Customer Assistance. The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See Customer Satisfaction Procedure on page 478. 81 Restraint System Check Checking the Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. See Care of Safety Belts on page 442 for more information. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. If you damage the covering for the Also look for any opened or broken airbag covers, and have them repaired or replaced. The airbag system does not need regular maintenance. Notice: driver’s or the right front passenger’s airbag, or the side impact airbag covering (if equipped) on the ceiling near the side windows, the airbag may not work properly. You may have to replace the airbag module in the steering wheel, both the airbag module and the instrument panel for the right front passenger’s airbag, or side impact airbag module and ceiling covering for roof-mounted side impact airbags (if equipped.) Do not open or break the airbag coverings. 82 Replacing Restraint System Parts After a Crash {CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. If you have had a crash, do you need new belts or LATCH system parts? After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be if worn during a more severe crash, then you need new parts. If the LATCH system was being used during a more severe crash, you may need new LATCH system parts. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have LATCH system, safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt or LATCH system was not being used at the time of the collision. If an airbag inﬂates, you will need to replace airbag system parts. See the part on the airbag system earlier in this section. If the frontal airbags inﬂate, you will also need to replace the driver’s and right front passenger’s safety belt buckle assembly. Be sure to do so. Then the new buckle assembly will be there to help protect you in a collision. After a crash you may need to replace the driver and front passenger’s safety belt buckle assemblies, even if the frontal airbags have not deployed. The driver and front passenger’s safety belt buckle assemblies contain the safety belt pretensioners. Have your safety belt pretensioners checked if your vehicle has been in a collision, or if your airbag readiness light stays on after you start your vehicle or while you are driving. See Airbag Readiness Light on page 182. 83 ✍ NOTES 84 Section 2 Features and Controls Keys .............................................................. 87 Remote Keyless Entry (RKE) System .......... 89 Remote Keyless Entry (RKE) System Operation ................................................. 90 Doors and Locks .......................................... 96 Door Locks ................................................. 96 Power Door Locks ....................................... 97 Delayed Locking .......................................... 97 Automatic Door Lock ................................... 98 Programmable Automatic Door Unlock ........ 98 Rear Door Security Locks ........................... 98 Lockout Protection ....................................... 99 Trunk ........................................................ 100 Windows ...................................................... 102 Power Windows ........................................ 103 Sun Visors ................................................ 104 Theft-Deterrent Systems ............................. 104 Content Theft-Deterrent ............................. 104 PASS-Key® III ........................................... 106 PASS-Key® III Operation ........................... 107 Starting and Operating Your Vehicle ......... 109 New Vehicle Break-In ................................ 109 Ignition Positions ....................................... 109 Retained Accessory Power (RAP) ............. 110 Starting the Engine .................................... 111 Engine Coolant Heater .............................. 112 Automatic Transaxle Operation .................. 114 Parking Brake ........................................... 117 Shifting Into Park (P) ................................. 118 Shifting Out of Park (P) ............................. 120 Parking Over Things That Burn ................. 121 Engine Exhaust ......................................... 122 Running the Engine While Parked ............. 123 Mirrors ......................................................... 124 Manual Rearview Mirror ............................. 124 Manual Rearview Mirror with OnStar® ....... 124 Automatic Dimming Rearview Mirror .......... 124 Automatic Dimming Rearview Mirror with OnStar® .......................................... 125 Outside Power Mirrors ............................... 125 Outside Power Heated Mirrors ................... 126 Outside Convex Mirror ............................... 126 85 Section 2 Features and Controls OnStar® System .......................................... 126 Universal Home Remote System ................ 130 Universal Home Remote System (With Three Round LED) ....................... 130 Universal Home Remote System (With One Triangular LED) ..................... 130 Universal Home Remote System Operation (With Three Round LED) ....... 131 Universal Home Remote System Operation (With One Triangular LED) ...................... 137 Storage Areas ............................................. 141 Glove Box ................................................. 141 Cupholder(s) .............................................. 141 Center Console Storage Area .................... 142 Convenience Net ....................................... 142 Sunroof ....................................................... 143 86 Keys {CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children. 87 instrument panel. The key will have PK3 stamped on it. If a replacement key or an additional key is needed, it must be purchased from your dealer or certiﬁed locksmith. Any new PASS-Key® III key must be programmed before it will start the vehicle. See PASS-Key® III on page 106 for more information on programming a new key. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 484 for more information. Notice: vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. If you ever lock your keys in your One key is used for the ignition and all locks. When a new vehicle is delivered, the key has a bar-coded key tag. This tag may be removed by your dealer before it is delivered. The vehicle has the PASS-Key® III vehicle theft system. The key has a transponder in the key head that matches a decoder in the vehicle’s 88 Remote Keyless Entry (RKE) System Your Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. At times you may notice a decrease in operating range. This is normal for any RKE system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: (cid:127) Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. (cid:127) Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left or right, hold the transmitter higher, and try again. (cid:127) Check to determine if battery replacement is necessary. See “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 90. If you are still having trouble, see your dealer or a qualiﬁed technician for service. (cid:127) 89 The following functions may be available with your vehicle’s RKE system: /(Remote Vehicle Start): If your vehicle has this feature, the engine may be started from outside the vehicle using the RKE transmitter. See “Remote Vehicle Start” at the end of this section for more detailed information. Q(Lock): Press the lock button to lock all the doors. If enabled through the Driver Information Center (DIC), the parking lamps may ﬂash once to indicate locking has occurred, or the horn may chirp when the lock button is pressed again within ﬁve seconds from the previous press of the lock button. See “FOB LOCK FEEDBACK” under DIC Vehicle Personalization on page 229 for additional information. If the vehicle has the content theft-deterrent system, pressing the lock button may also arm it. See Content Theft-Deterrent on page 104. Remote Keyless Entry (RKE) System Operation The vehicle’s doors can be locked and unlocked, and the trunk can be opened from about 3 feet (1 m) up to 60 feet (18 m) away with the Remote Keyless Entry (RKE) transmitter. If your vehicle has the remote start feature, you can also start the vehicle’s engine with the RKE transmitter. RKE with Remote Start RKE without Remote Start 90 " (Unlock): Press the unlock button to unlock the driver’s door. If the button is pressed again within ﬁve seconds, all remaining doors will unlock. The interior lamps will come on and stay on for 20 seconds or until the ignition is turned on. If enabled through the DIC, the parking lamps can be programmed to come on for a set amount of time when the vehicle is unlocked using the RKE transmitter. See “EXT (Exterior) LIGHT DELAY” under DIC Vehicle Personalization on page 229. If the vehicle has the content theft-deterrent system, pressing the unlock button on the RKE transmitter may disarm it. See Content Theft-Deterrent on page 104. V(Remote Trunk Release): Press and hold this button for about one second to release the trunk lid. The transaxle must be in PARK (P) for this feature to operate. L(Panic Alarm): Press this button to activate the alarm. The ignition must be in OFF or ACCESSORY for the alarm to work. When the alarm button is pressed, the headlamps will ﬂash and the horn will sound repeatedly for two minutes. The alarm will turn off when the ignition is moved to RUN or the alarm button is pressed again. Matching Transmitter(s) to Your Vehicle Each RKE transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your GM dealer. Remember to bring any additional transmitters so they can also be re-coded to match the new transmitter. Once your dealer has coded the new transmitter, the lost transmitter will not unlock your vehicle. The vehicle can have a maximum of four transmitters matched to it. Battery Replacement Under normal use, the battery in the RKE transmitter should last about four years. The battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery. The KEY FOB BATT LOW message in the vehicle’s DIC will display if the RKE transmitter battery is low. 91 Notice: When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter. 2. Remove the old battery. Do not use a metal object to do this. 3. Slide the new battery into the transmitter with the positive (+) side of the battery facing up. Use one three-volt, CR2032 battery, or equivalent type. 4. Snap the front and the back of the transmitter together. Make sure the cover is on tight, so water will not get inside the transmitter. 5. Test the operation of the transmitter with the vehicle. To replace the battery in the RKE transmitter, do the following: 1. Insert a ﬂat object, with a thin edge, into the notch located below the panic alarm button, and separate the bottom half from the top half of the transmitter. 92 Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active, the climate control system will heat or cool the inside of the vehicle based on the outside temperature. The rear window defogger will be turned on by the climate control system when it is heating the inside of the vehicle. Normal operation of the system will return after the key is turned to the RUN position. Laws in some communities may restrict the use of remote starters. For example, some laws may require a person using remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. Do not use the remote start feature if your vehicle is low on fuel. Your vehicle may run out of fuel. The remote start feature provides two separate starts per ignition cycle, each with 10 minutes of engine running time. The remote vehicle start feature needs to be reset after your vehicle’s engine is started two times using the transmitter’s remote start button. The remote start system is reset by inserting the vehicle’s key into the ignition switch and turning it to RUN. See Ignition Positions on page 109 for information regarding the ignition positions on your vehicle. The RKE transmitter with the remote start button provides an increased range of operation. You can start your vehicle from an average range of about 492 feet (150 m) away. However the range may be less while the vehicle is running, and as a result, you may need to be closer to your vehicle to turn it off than you were to turn it on. There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry (RKE) System on page 89 for additional information. 93 4. To manually shut off a remote start, do any of the following. The parking lamps will turn off: (cid:127) Aim the RKE transmitter at the vehicle and press the remote start button. (cid:127) Turn on the hazard warning ﬂashers. (cid:127) Turn the ignition switch to RUN and then to OFF. Your vehicle’s engine may be started two times using the transmitter’s remote start feature. If only one remote start procedure has been done, since last driving the vehicle, or resetting the remote start system, the engine may be started again remotely following the remote start procedure a second time If the remote start procedure is used again before the ﬁrst 10 minute time frame has ended, the ﬁrst 10 minutes will immediately expire and the second 10 minute time frame will start. /(Remote Start): If your vehicle has the remote start feature, the RKE transmitter will have a button with this symbol on it. To start the vehicle using the remote start feature, do the following: 1. Aim the transmitter at the vehicle. 2. Press and release the transmitter’s lock button, then immediately press and hold the transmitter’s remote start button for four seconds or until the turn signal lamps ﬂash. The vehicle’s doors will lock. 3. When the vehicle’s engine starts, the parking lamps will turn on and remain on while the engine is running. The engine will shut off automatically after 10 minutes, unless a time extension has been done or the vehicle’s key is inserted into the ignition switch and turned to RUN. If you enter the vehicle after a remote start, and the engine is still running, insert the key into the ignition switch and turn it to RUN to drive the vehicle. 94 The remote vehicle start feature will not operate if any of the follow occur: (cid:127) The remote start system is disabled through the DIC. (cid:127) The vehicle’s key is in the ignition. (cid:127) A door on the vehicle is open. (cid:127) The vehicle’s hood is open. (cid:127) The hazard warning ﬂashers are on. (cid:127) The check engine light is on. See Malfunction Indicator Lamp on page 190. (cid:127) The engine coolant temperature is too high. (cid:127) The oil pressure is low. (cid:127) Two remote vehicle starts have already been provided for that ignition cycle. If a remote start is attempted and is unsuccessful, the Driver Information Center (DIC) will display REMOTE START DISABLED. Vehicles that have the remote vehicle start feature are shipped from the factory with the remote vehicle start system enabled. The system may be enabled or disabled through the DIC. See “REMOTE START” under DIC Vehicle Personalization on page 229 for additional information. If your vehicle does not have the DIC feature, and remote vehicle start was installed at the dealership, you will need to have the dealership enable or disable the system. Remote Start Ready If your vehicle does not have the remote vehicle start feature, it may have the remote start ready feature. This feature gives you the ability to lock or unlock your vehicle from about 492 feet (150 m) away and allows your dealer to add the manufacturer’s remote vehicle start feature. See your dealer if you would like to add the manufacturer’s remote vehicle start feature to your vehicle. 95 CAUTION: (Continued) (cid:127) Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. Locking your doors can help prevent this from happening. There are several ways to lock and unlock the vehicle. From the outside, turn the key in the driver’s door lock cylinder brieﬂy counterclockwise to unlock the driver’s door. Turn and hold it to unlock all the doors. You can also use the remote keyless entry transmitter. From the inside use the manual or power door locks. Doors and Locks Door Locks {CAUTION: Unlocked doors can be dangerous. (cid:127) Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked. So, wear safety belts properly and lock the doors whenever you drive. (cid:127) Young children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock your vehicle whenever you leave it. CAUTION: (Continued) 96 Power Door Locks To lock or unlock all doors from inside the vehicle, use the power door lock switch located on either front door armrest. Press the bottom of the switch to lock all doors. Press the top of the switch to unlock all doors. The driver’s and front passenger’s power door lock switch also releases the trunk lid. Press the top of the switch for about one and a half seconds to open the trunk. If the vehicle has the content theft-deterrent system, the vehicle is programmed to arm the system with the power door lock switch. If your vehicle has a Driver Information Center (DIC) this feature can be turned off. See “Content Theft” under DIC Vehicle Personalization on page 229. Delayed Locking Your vehicle may have this feature. It delays the locking of the vehicle’s doors for ﬁve seconds after the last door is closed. Two chimes will sound when the power door lock switch or the LOCK button on the remote keyless entry transmitter is pressed when a door is open. The chimes indicate that the delayed locking feature is on. If your vehicle has a Driver Information Center (DIC), a Delayed Locking warning will be displayed. The doors can be locked immediately by pressing the power door lock switch or the LOCK button on the transmitter a second time. The delayed locking feature will not activate when the ignition is in RUN or ACCESSORY. You can program this feature on or off through the Driver Information Center (DIC), if equipped. See “Delayed Locking” under DIC Vehicle Personalization on page 229. 97 Automatic Door Lock The vehicle’s doors are programmed to lock when the shift lever is moved into a forward gear. If someone needs to get in or out of the vehicle after the doors have been locked, place the shift lever into PARK (P). You may also unlock all doors using the power door lock switch or unlock one door using the inside manual door lock. The automatic door lock feature cannot be disabled. Programmable Automatic Door Unlock The vehicle’s doors are programmed from the factory to unlock when the shift lever is moved into PARK (P). If your vehicle has a Driver Information Center (DIC), there are different programming options for unlocking the doors automatically. See DIC Vehicle Personalization on page 229. 98 Rear Door Security Locks Your vehicle has rear door security locks. These prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them. To set the locks, do the following: 1. Insert the key into the security lock slot and turn it so the slot is in the horizontal position. 2. Close the door. When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, if equipped, the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside. To cancel the rear door security lock, do the following: 1. Unlock the door and open it from the outside. 2. Insert the key into the security lock slot and turn it so the slot is in the vertical position. Lockout Protection The lockout protection feature makes it more difficult to lock the key in the vehicle. If the driver’s door is open while the key is in the ignition, the door cannot be locked with the power door lock switch. This feature cannot guarantee that you will never be locked out of the vehicle. If the key is not left in the ignition, or, if the manual door lock is used, the key could still be locked inside the vehicle. Always remember to take the key with you. 99 Trunk {CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid: (cid:127) Make sure all other windows are shut. (cid:127) Turn the fan on your heating or cooling system to its highest speed and select the control setting that will force outside air into your vehicle. See Climate Control System. (cid:127) If you have air outlets on or under the instrument panel, open them all the way. Opening the Trunk To open the trunk from the outside, use the Remote Keyless Entry (RKE) transmitter. See Remote Keyless Entry (RKE) System Operation on page 90 for more information. The ignition must be off, or the transaxle must be in PARK (P) to open the trunk. Remote Trunk Release This feature is used to unlock the trunk from inside the vehicle using the power door lock switch. Press and hold the top of the driver’s or front passenger’s power door lock switch to unlock the trunk. See Engine Exhaust on page 122. The vehicle must be in PARK (P) to unlock the trunk. 100 Emergency Trunk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside. Trunk Lid Pull Down Handle and Tie-Down Features There is a glow-in-the-dark emergency trunk release handle located on the trunk latch of the trunk lid. This handle will glow following exposure to light. If ever needed, pull the emergency trunk release handle to open the trunk from the inside. Your vehicle has a trunk lid pull down handle (A) located on the inside of the trunk lid on the driver’s side of the vehicle. Use the handle to pull down the trunk lid when closing it. Your vehicle also has a tie-down feature (B) located on the inside the trunk lid on the passenger’s side of the vehicle that can be used to secure the trunk lid when large items are stored in the trunk. 101 Windows {CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 102 Power Windows The switches on the driver’s door armrest are used to control each of the windows. The power window switches work while the ignition is in RUN, ACCESSORY, or while Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 110. Each passenger door has its own window switch. To lower the window, press and hold the front of the switch to the ﬁrst position until the window is at the desired level. To raise the window, pull up and hold the front of the switch. Express-Down Window The driver’s window switch has an express-down feature labeled AUTO. This lets you lower the window completely without holding the switch. Press the front of the switch to the second position and release. To stop the window while it is lowering, brieﬂy pull up on the switch. Window Lockout o(Window Lockout): The driver’s window switches also include a lockout switch. Press the right side of the switch to prevent the rear passengers from using their window switches. The driver can still control all the windows and the front passenger can control their own window with the lockout on. Press the left side of the switch to return to normal window operation. A visible red bar on the right side of the switch indicates that the lockout is off. 103 Sun Visors To block out glare, swing down the sun visors. They can be detached from the center retainer and slid along the rod to cover different areas of the front window and turned to cover the side windows. Visor Vanity Mirror Swing down the sun visors and lift the cover to expose the vanity mirror. Do not drive with the cover lifted due to possible glare impeding other drivers behind or to the side of the vehicle. Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. 104 Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system. A red light located on top of the instrument panel, toward the center of the vehicle and near the windshield, will ﬂash slowly when the system is armed. The theft-deterrent alarm system needs to be activated through the Driver Information Center (DIC). See “CONTENT THEFT” under “Customization Menu Items” in DIC Vehicle Personalization on page 229. While armed, the doors will not unlock with the power door lock switch. The remote alarm will sound if someone tampers with the trunk or enters the vehicle without using the remote keyless entry transmitter or key to unlock the doors. The horn will sound and the headlamps will ﬂash for up to two minutes. The system will also cut off the fuel supply, preventing the vehicle from being driven. Arming with the Power Lock Switch The vehicle’s content theft-deterrent alarm system can be activated when the key is removed from the ignition and the power door lock switch of either the driver’s or front passenger’s door is used to lock the vehicle. The door needs to be in the open position when pressing the power door lock switch. The alarm system will not activate if the door is closed when the power door lock switch is pressed. This system can be activated through the Driver Information Center (DIC). See “CONTENT THEFT” under “Customization Menu Items” in DIC Vehicle Personalization on page 229. When the doors are locked using the power door lock switch of either front door, the red light on top of the instrument panel will start ﬂashing at a fast rate, indicating that the system is arming. After all the doors are locked there will be a time delay and then the red light will begin to ﬂash at a very slow rate, indicating the system is armed. Arming with the Remote Keyless Entry Transmitter The alarm system will arm when the remote keyless entry transmitter is used to lock the doors after the key is removed from the ignition. The red light will come on to indicate that the system is arming. After all doors are closed and locked, and after a time delay, the red light will begin ﬂashing at a very slow rate to show the system is armed. Arming Conﬁrmation A red light located on top of the instrument panel, towards the center of the vehicle and near the windshield, will ﬂash slowly to conﬁrm when the system is armed. Disarming with the Remote Keyless Entry Transmitter The alarm system will disarm when the remote keyless entry transmitter is used to unlock the doors. The red light will go out to show that the system is disarmed. 105 Disarming with Your Key The alarm system will disarm when the key is used to unlock the doors. The red light will stop ﬂashing when the system is disarmed. If you would like the key to disarm the alarm system, see “CONTENT THEFT” under DIC Vehicle Personalization on page 229 for more information. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. PASS-Key® III uses a radio frequency transponder in the key that matches a decoder in your vehicle. PASS-Key® III Your PASS-Key® III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 106 PASS-Key® III Operation Your vehicle is equipped with PASS-Key® III (Personalized Automotive Security System) theft-deterrent system. PASS-Key® III is a passive theft-deterrent system. This means nothing special needs to be done to arm or disarm the system. It works when the key is inserted or removed from the ignition. PASS-Key III® uses a transponder in the ignition key that matches a decoder in the vehicle. When the PASS-Key® III system senses that the wrong key has been inserted into the ignition, it shuts down the vehicle’s starter and fuel systems. The starter will not work and fuel will stop ﬂowing to the engine. If someone tries to start the vehicle again with the wrong key, the vehicle will not start. Anyone using a trial-and-error method to start the vehicle will be discouraged to do so because of the high number of electrical key codes. When trying to start the vehicle, if the engine does not start and the STARTING DISABLED warning message on the Driver Information Center (DIC) comes on, the key may have a damaged transponder. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 450. If the engine still does not start with the other key, the vehicle needs service. If the vehicle does start, the ﬁrst key may be faulty. See your dealer who can service the PASS-Key® III to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 484 for more information. 107 It is possible for the PASS-Key® III decoder to accept the transponder value of a new or replacement key. Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only. If all the programmed keys are lost or do not operate, see your dealer or a locksmith who can service PASS-Key® III to have keys made and programmed to the system. To program the new key do the following: 1. Verify that the new key has PK3 stamped on it. 2. Insert the master key in the ignition and start the engine. If the engine will not start, see your dealer for service. 3. After the engine has started, turn the key to OFF, and remove the key. 4. Insert the key to be programmed and turn it to RUN within ﬁve seconds of removing the original key. 5. The SERVICE THEFT SYSTEM warning message on the DIC will turn off, once the key has been programmed. It may not be apparent that the SERVICE THEFT SYSTEM warning message went on due to how quickly the key is programmed. 6. Repeat Steps 1 through 5 if additional keys are to be programmed. If the SERVICE THEFT SYSTEM warning message appears and stays on the DIC while the vehicle is being driven, the engine will be able to be restarted if it is turned off. Your PASS-Key® III system, however, is not working properly and must be serviced by your dealer. The vehicle is not protected by the PASS-Key® III system at this time. If the PASS-Key® III key is lost or stolen, see your dealer or a locksmith who can service PASS-Key® III to have a new key made. 108 Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: (cid:127) Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km). Do not make full-throttle starts. Avoid downshifting to brake, or slow, the vehicle. (cid:127) Avoid making hard stops for the ﬁrst 200 miles (322 km) or so. During this time your new brake linings are not yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. (cid:127) Do not tow a trailer during break-in. See Towing a Trailer on page 327 for the trailer towing capabilities of your vehicle and more information. Following break-in, engine speed and load can be gradually increased. Ignition Positions With the ignition key in the ignition, the key can be turned to four different positions: Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand. Make sure the key is in all the way. If none of this works, then your vehicle needs service. A (OFF): This is the only position in which the ignition key can be inserted or removed. This position locks the ignition and transaxle. It is a theft-deterrent feature. 109 B (ACCESSORY): This position lets the radio and windshield wipers operate while the engine is off. To use ACCESSORY, turn the key clockwise. C (RUN): This position is where the key returns to after the vehicle is started. This position displays some of the warning and indicator lights. The battery could be drained if you leave the key in the ACCESSORY or RUN position with the engine off. You may not be able to start your vehicle if the battery is allowed to drain for an extended period of time. D (START): This position starts the engine. A warning chime will sound and the Driver Information Center (DIC) will display DRIVER’S DOOR AJAR when the driver’s door is opened if the ignition is in OFF, ACCESSORY and the key is in the ignition. See DIC Warnings and Messages on page 208 for more information. Key In the Ignition Never leave your vehicle with the keys inside, as it is an easy target for joy riders or thieves. If you leave the key in the ignition and park your vehicle, a chime will sound, when you open the driver’s door. Always remember to remove your key from the ignition and take it with you. This will lock your ignition and transaxle. Also, always remember to lock the doors. The battery could be drained if you leave the key in the ignition while your vehicle is parked. You may not be able to start your vehicle after it has been parked for an extended period of time. Retained Accessory Power (RAP) If the vehicle has Retained Accessory Power (RAP), the power windows and radio will continue to operate for up to 10 minutes after the ignition key is turned to OFF unless a door is opened. 110 Starting the Engine Place the transaxle in the proper gear. Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position — this is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle. Shift into PARK (P) only when your vehicle is stopped. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it. Operate the engine and transaxle gently to allow the oil to warm up and lubricate all moving parts. Your vehicle has a Computer-Controlled Cranking System. This feature assists in starting the engine and protects components. If the ignition key is turned to the START position, and then released when the engine begins cranking, the engine will continue cranking for a few seconds or until the vehicle starts. If the engine does not start and the key is held in START for many seconds, cranking will be stopped after 15 seconds to prevent cranking motor damage. To prevent gear damage, this system also prevents cranking if the engine is already running. Engine cranking can be stopped by turning the ignition switch to the ACCESSORY or OFF position. Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. 111 Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F (−18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. At temperatures above 32°F (0°C), use of the coolant heater is not required. Your vehicle may also have an internal thermostat in the plug end of the cord. This will prevent operation of the engine coolant heater when the temperature is at or above 0°F (−18°C) as noted on the cord. 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds. Wait at least 15 seconds between each try, to allow the cranking motor to cool down. When the engine starts, let go of the key and accelerator. If the vehicle starts brieﬂy but then stops again, do the same thing. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transaxle gently until the oil warms up and lubricates all moving parts. Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly. Any resulting damage would not be covered by your vehicle’s warranty. 112 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you will be parking your vehicle. The dealer can give you the best advice for that particular area. To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is attached to the underside of the diagonal brace, which is located above the engine air cleaner/ﬁlter assembly. 3. Plug it into a normal, grounded 110-volt AC outlet. {CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 113 Automatic Transaxle Operation Your vehicle’s automatic transaxle may have a shift lever on the steering column or on the console between the seats. Console Shift Lever There is also a display located on the instrument panel cluster that indicates the vehicle’s gear position. 114 {CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). See Shifting Into Park (P) on page 118. If you are pulling a trailer, see Towing a Trailer on page 327. The positions for the shift lever are: PARK (P): This position locks the vehicle’s front wheels. It is the best position to use when the engine is started because the vehicle cannot move easily. Make sure the shift lever is fully in PARK (P) before starting the engine. The vehicle has an electronic shift lock release system. You must fully apply the regular brakes before shifting from PARK (P) when the ignition is in RUN. If you cannot shift out of PARK (P), ease pressure on the shift lever by pushing it all the way into PARK (P) as you maintain brake application. Then move the shift lever into another gear. See Shifting Out of Park (P) on page 120 Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. REVERSE (R): Use this gear to back up. To rock the vehicle back and forth in order to get it out of snow, ice, or sand without damaging the transaxle, see If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 318. NEUTRAL (N): In this position, the engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when the vehicle is being towed. {CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed. Notice: Shifting out of PARK (P) or NEUTRAL (N) while the engine is running at high speed may damage the transaxle. The repairs would not be covered by your warranty. Be sure the engine is not running at high speeds when shifting your vehicle. Notice: Driving your vehicle if you notice that it is moving slowly or not shifting gears as you increase speed may damage the transaxle. Have your vehicle serviced right away. You can drive in SECOND (2) when you are driving less than 35 mph (55 km/h) and DRIVE (D) for higher speeds until then. 115 DRIVE (D): This position is for normal driving. It provides the best fuel economy for your vehicle. If more power is needed for passing, and the vehicle is: (cid:127) Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. (cid:127) Going about 35 mph (55 km/h) or more, push the accelerator pedal all the way down. By doing this the vehicle will automatically shift down to the next gear and have more power. Downshifting the transaxle in slippery road conditions could result in skidding, see Skidding under Loss of Control on page 302. THIRD (3): This position is also used for normal driving. However it reduces vehicle speed more than DRIVE (D) without using your brakes. You might choose THIRD (3) instead of DRIVE (D) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or DRIVE (D) instead of SECOND (2). SECOND (2): This position reduces vehicle speed even more than THIRD (3) without using your brakes. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. FIRST (1): This position reduces vehicle speed even more than SECOND (2) without using your brakes. You can use it on very steep hills, or in deep snow or mud. If the shift lever is put in FIRST (1) while the vehicle is moving forward, the transmission will not shift into ﬁrst gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transaxle. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes, or parking brake to hold the vehicle in place. 116 Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. To release the parking brake, hold the regular brake pedal down with your right foot and push the parking brake pedal with your left foot. While you lift your left foot, the parking brake pedal will follow it to the released position. A warning chime will sound and PARKING BRAKE ON will display in the DIC if the parking brake is set, the ignition is on, and the vehicle speed is greater than 5 mph (8km/h). For more information see Brake System Warning Light on page 186 and DIC Warnings and Messages on page 208. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and parking on any hill, see Towing a Trailer on page 327. That section shows what to do ﬁrst to keep the trailer from moving. 117 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Console Shift Lever 1. Hold the brake pedal down and set the parking brake. 2. Move the shift lever into the PARK (P) position by holding in the button on the shift lever and pushing it all the way toward the front of the vehicle. 3. Turn the ignition key to OFF. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Shifting Into Park (P) {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, use the steps that follow. If you are pulling a trailer, see Towing a Trailer on page 327. Steering Column Shift Lever 1. Hold the brake pedal down and set the parking brake. 2. Move the shift lever into the PARK (P) like this: (cid:127) Pull the lever toward you. (cid:127) Move the lever up as far as it will go. 118 Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To ﬁnd out how, see Shifting Into Park (P) on page 118. When you are ready to drive, move the shift lever out of PARK (P) before you release the parking brake. If torque lock does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the parking pawl in the transaxle, so you can pull the shift lever out of PARK (P). Leaving Your Vehicle With the Engine Running {CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre. You or others could be injured. Do not leave your vehicle with the engine running. If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you have moved the shift lever into PARK (P), hold the regular brake pedal down. Then, see if you can move the shift lever away from PARK (P) without ﬁrst pushing the button. If you can, it means that the shift lever was not fully locked into PARK (P). 119 Shifting Out of Park (P) Automatic Transaxle Shift Lock This vehicle has an electronic shift lock release system. The shift lock release is designed to: (cid:127) Prevent ignition key removal unless the shift lever is in PARK (P) (cid:127) Prevent movement of the shift lever out of PARK (P) unless the ignition is in a position other than OFF. The shift lock is always functional except in the case of a an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery. See Jump Starting on page 385. Console Shift If your console shift cannot be moved out of PARK (P) 1. Apply and maintain the regular brakes. 2. Turn the ignition to the ACESSORY or RUN position. See Ignition Positions on page 109 for more information. 120 3. Let up on the shift lever and make sure the shift lever is pushed all the way into PARK (P). 4. Then, move the shift into the desired gear. If you still cannot move the shift lever from PARK (P), consult your dealer or a professional towing service. Column Shift If your park lock cable cannot be moved out of PARK (P) 1. Apply and maintain the regular brakes. 2. Turn the ignition key to the ACCESSORY or RUN position. See Ignition Positions on page 109 for more information. 3. Shift out of the PARK (P) position to the NEUTRAL (N) position. 4. Move the vehicle to a safe location. If you still cannot move the shift lever from PARK (P), consult your dealer or a professional towing service. Parking Over Things That Burn {CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 121 CAUTION: (Continued) (cid:127) Your vehicle was damaged when driving over high points on the road or over road debris. (cid:127) Repairs were not done correctly. (cid:127) Your vehicle or exhaust system has been modiﬁed improperly. If you ever suspect exhaust is coming into your vehicle: (cid:127) Drive it only with all the windows down to blow out any CO; and (cid:127) Have your vehicle ﬁxed immediately. Engine Exhaust {CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: (cid:127) Your exhaust system sounds strange or different. (cid:127) Your vehicle gets rusty underneath. (cid:127) Your vehicle was damaged in a collision. CAUTION: (Continued) 122 Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. {CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier caution under Engine Exhaust on page 122. Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting. One place this can happen is a garage. Exhaust — with CO — can come in easily. NEVER park in a garage with the engine running. Another closed-in place can be a blizzard. See Winter Driving on page 314. {CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Follow the proper steps to be sure your vehicle will not move. See Shifting Into Park (P) on page 118. If you are parking on a hill and if you are pulling a trailer, also see Towing a Trailer on page 327. 123 Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The day/night control at the bottom of the mirror lets you adjust the mirror to avoid glare from the lamps behind you. Turn the control to the right for nighttime conditions and to the center for daytime conditions. Manual Rearview Mirror with OnStar® The vehicle may have a mirror with Onstar®. While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up and down and side to side. The mirror has a day/night control located at the bottom. Turn the control to the right for the night position to reduce glare from other vehicles’ headlamps. Turn the control to the front for the day position. 124 There are also three OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 126 for more information about the services OnStar® provides. Automatic Dimming Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The vehicle may have an automatic dimming rearview mirror that darkens gradually to reduce the glare of headlamps from behind. Press the button in the center of the mirror to turn this feature on or off. One photocell on the front of the mirror senses when it is becoming dark outside. Another photocell, facing rearward, senses headlamps behind you. To keep the photocells operating well, occasionally clean them with a cotton swab and glass cleaner. Automatic Dimming Rearview Mirror with OnStar® While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. The vehicle may have an automatic dimming rearview mirror with the OnStar® System. The automatic dimming feature is turned on or off by pressing the left button, located on the lower part of the mirror, for up to three seconds. When turned on, this mirror functions like the automatic dimming rearview mirror described previously. See Automatic Dimming Rearview Mirror on page 124. There are also three OnStar® buttons located at the bottom of the mirror. See your dealer for more information on the system and how to subscribe to OnStar®. See OnStar® System on page 126 for more information about the services OnStar® provides. Outside Power Mirrors The controls for the outside power mirrors, are located on the driver’s door armrest. Move the selector switch located below the four-way control pad to the left or right to choose either the driver’s side or passenger’s side mirror. To adjust a mirror, use the arrows located on the four-way control pad to move the mirror in the desired direction. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen while sitting in a comfortable driving position. Keep the selector switch in the center position when not adjusting either outside mirror. 125 Outside Power Heated Mirrors For information on the operation of the outside power mirrors see Outside Power Mirrors on page 125. If the vehicle has heated mirrors, they will warm up to melt ice and snow, and remove condensation when the defroster is turned on. See Dual Automatic Climate Control System on page 172 or Climate Control System on page 168. Outside Convex Mirror {CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right. Check your inside mirror or glance over your shoulder before changing lanes. 126 The passenger’s side mirror is convex. A convex mirror’s surface is curved so more can be seen from the driver’s seat, but it also makes things look farther away than they really are. OnStar® System OnStar® uses several innovative technologies and live advisors to provide you with a wide range of safety, security, information, and convenience services. If your airbags deploy, the system is designed to make an automatic call to OnStar® Emergency advisors who can request emergency services be sent to your location. If you lock your keys in the vehicle, call OnStar® at 1-888-4-ONSTAR and they can send a signal to unlock your doors. If you need roadside assistance, press the OnStar® button and they can contact Roadside Service for you. OnStar® service is provided to you subject to the OnStar® Terms and Conditions. You may cancel your OnStar® service at any time by contacting OnStar® as provided below. A complete OnStar® Owners Guide and the OnStar® Terms and Conditions are included in the vehicle’s OnStar® Subscriber glove box literature. For more information, visit onstar.com or onstar.ca, contact OnStar® at 1-888-4-ONSTAR (1-888-466-7827) or TTY 1-877-248-2080, or press the OnStar® button to speak with an OnStar® advisor 24 hours a day, 7 days a week. Not all OnStar® features are available on all vehicles. To check if your vehicle is equipped to provide the services described below, or for a full description of OnStar® services and system limitations, see the OnStar® Owner’s Guide in your glove box or visit onstar.com. OnStar® Services For new vehicles with OnStar®, the Safe & Sound Plan, or the Directions & Connections® Plan is included for one year from the date of purchase. You can extend this plan beyond the ﬁrst year, or upgrade to the Directions & Connections® Plan. For more information, press the OnStar® button to speak with an advisor. Some OnStar® services (such as Remote Door Unlock or Stolen Vehicle Location Assistance) may not be available until you register with OnStar®. Available Services with Safe & Sound® Plan (cid:127) Automatic Notiﬁcation of Airbag Deployment (cid:127) Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) (cid:127) Link to Emergency Services (cid:127) Roadside Assistance (cid:127) Stolen Vehicle Location Assistance (cid:127) AccidentAssist (cid:127) Remote Door Unlock/Vehicle Alert (cid:127) OnStar® Vehicle Diagnostics (cid:127) GM® Goodwrench® On Demand Diagnostics (cid:127) OnStar® Hands-Free Calling with 30 complimentary minutes (cid:127) OnStar® Virtual Advisor ( U.S. Only) 127 Available Services included with Directions & Connections® Plan (cid:127) All Safe and Sound Plan Services (cid:127) Driving Directions - Advisor delivered or OnStar® Turn-by-Turn Navigation (If equipped) Information and Convenience Services (cid:127) RideAssist (cid:127) OnStar® Hands-Free Calling OnStar® Hands-Free Calling allows eligible OnStar® subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar® Pre-Paid Minute Packages. Hands-Free Calling may also be linked to a Verizon Wireless service plan in the U.S. or a Bell Mobility service plan in Canada, depending on eligibility. To ﬁnd out more, refer to the OnStar® Owners Guide in the vehicle’s glove box, visit www.onstar.com or www.onstar.ca, or speak with an OnStar® advisor by pressing the OnStar® button or calling 1-888-4-ONSTAR (1-888-466-7827). OnStar® Virtual Advisor OnStar® Virtual Advisor is a feature of OnStar® Hands-Free Calling that uses your minutes to access location-based weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics. See the OnStar® Owners Guide for more information (Only available in the continental U.S.). OnStar® Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar® Hands-Free Calling. See Audio Steering Wheel Controls on page 280 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR” in order to activate the OnStar® Hands-Free Calling feature. On some vehicles, the mute button can be used to dial numbers into voicemail systems, or to dial phone extensions. See the OnStar® Owner’s Guide for more information. 128 How OnStar® Service Works In order to provide you with OnStar® services, your vehicle’s OnStar® system has the capability of recording and transmitting vehicle information. This information is automatically sent to an OnStar® Call Center at the time of an OnStar® button press, Emergency button press or if your airbags or AACN system deploys. The vehicle information usually includes your GPS location and, in the event of a crash, additional information regarding the accident that your vehicle has been involved in (e.g. the direction from which your vehicle was hit). When you use the Virtual Advisor feature of OnStar® Hands-Free Calling, your vehicle also sends OnStar® your GPS location so that we can provide you with location-based services. OnStar® service cannot work unless your vehicle is in a place where OnStar® has an agreement with a wireless service provider for service in that area. OnStar® service also cannot work unless you are in a place where the wireless service provider OnStar® has hired for that area has coverage, network capacity and reception when the service is needed, and technology that is compatible with the OnStar® service. Not all services are available everywhere, particularly in remote or enclosed areas, or at all times. OnStar® service that involves location information about your vehicle cannot work unless GPS satellite signals are unobstructed and available in that place as well. Your vehicle must have a working electrical system (including adequate battery power) for the OnStar® equipment to operate. There are other problems OnStar® cannot control that may prevent OnStar® from providing OnStar® service to you at any particular time or place. Some examples are damage to important parts of your vehicle in an accident, hills, tall buildings, tunnels, weather or wireless phone network congestion. Your Responsibility You may need to increase the volume of your radio to hear the OnStar® advisor. If the light next to the OnStar® buttons is red, this means that your system is not functioning properly and should be checked by a dealer. If the light appears clear (no light is appearing), your OnStar® subscription has expired. You can always press the OnStar® button to conﬁrm that your OnStar® equipment is active. 129 Universal Home Remote System Universal Home Remote System (With Three Round LED) The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is KOBGTV06A. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 3521A-GTV06A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System (With One Triangular LED) The Universal Home Remote System provides a way to replace up to three hand-held radio-frequency (RF) transmitters used to activate devices such as garage door openers, security systems, and home lighting. 130 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC Grant of Equipment Authorization Certiﬁcate number is CB2SAHL3. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. The Canadian Registration ID number is 2791021849A. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment. Universal Home Remote System Operation (With Three Round LED) Your vehicle may have the Universal Home Remote System. If there are three round Light Emitting Diode (LED) above the Universal Home Remote System buttons, follow the instructions below. If there is one triangular LED above the Universal Home Remote System buttons, follow the instructions under Universal Home Remote System Operation (with one triangular LED). This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home lighting. Do not use the this system with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. 131 Read the instructions completely before attempting to program the transmitter. Because of the steps involved, it may be helpful to have another person available to assist you in programming the transmitter. Be sure to keep the original remote control transmitter for use in other vehicles, as well as, for future programming. You only need the original remote control transmitter for ﬁxed code programming. It is also recommended that upon the sale or lease termination of the vehicle, the programmed buttons should be erased for security purposes. See “Erasing your Universal Home Remote Buttons” later in this section. Be sure that people and objects are clear of the garage door or security device you are programming. When programming a garage door, it is advised to park outside of the garage. 132 If you do not know if your garage door opener is a ﬁxed code or rolling code device, open your garage door opener’s remote control battery cover. Your garage door opener is a ﬁxed code device if there is a panel of switches. If not, your garage door opener is a rolling code device. Programming Universal Home Remote — Fixed Code Fixed Code garage door openers are used for garage doors produced prior to 1996. Fixed code uses the same coded signal every time, which is manually programmed by setting DIP switches for a unique personal code. To program up to three channels, 1. Remove the battery cover of the hand-held transmitter. Example of Switch Settings 2. Write down the eight to 12 coding switch settings from left to right. When the switch is in the up position, write “on,” and when a switch is in the down position, write “off”. If a switch is set between the up and down position, write “middle”. 133 5. After entering the switch settings, press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light above the selected button should slowly blink. You may need to hold the button from ﬁve to 55 seconds. 7. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 8. Press and release the button again. The garage door should move, conﬁrming that programming is successful and complete. To program another device such as an additional garage door opener, a security device, or home lighting, repeat Steps 1–8, choosing a different function button in Step 7 than what you used for the garage door opener. 3. Enter these positions into the Universal Home Remote System as follows. Press and release all three buttons at the same time to put the device into programming mode. 4. The indicator light will blink slowly. In order from left to right, and within two and one-half minutes, enter each switch setting into the Universal Home Remote System. Push one button for each switch as follows: (cid:127) Left button = “on” switch position. (cid:127) Right button = “off” switch position. (cid:127) Middle button = “middle” switch position. 134 Programming Universal Home Remote — Rolling Code Rolling code garage door openers are used for garage doors produced after 1996 and are code protected. Rolling code means the coded signal is changed every time your remote control garage door opener is used. Programming a rolling code garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure. Follow these steps to program up to three channels: 1. Press the two outside buttons at the same time for one to two seconds, and immediately release them. 2. Go to the garage. Locate the garage door motor head and press and release the “learn” button. After pressing the “learn” button, you have 10 to 30 seconds to complete Step 4 depending on your garage control unit. If you cannot locate the “learn” button, refer to the owners guide for your garage door opener. 135 3. Press and hold the button you would like to use to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. You may need to hold the button from ﬁve to 20 seconds. 4. Immediately release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the button again. The garage door should move, conﬁrming that programming is successful and complete. To program another device such as an additional garage door opener, a security device, or home lighting, repeat Steps 1–5, choosing a different function button in Step 3 than what you used for the garage door opener. Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light will come on while the signal is being transmitted. Reprogramming Universal Home Remote Buttons You can reprogram any of the three buttons by repeating the instructions. Erasing Universal Home Remote Buttons You should erase the programmed buttons when you sell the vehicle or terminate your lease. To erase either rolling code or ﬁxed code on the Universal Home Remote device, do the following: 1. Press and hold the two outside buttons at the same time for approximately 20 seconds, until the indicator lights, located directly above the buttons, begin to blink rapidly. 2. Once the indicator lights begin to blink, release both buttons. The codes from all button will be erased. For additional information on Universal Home Remote, see Customer Assistance Offices on page 482. 136 Universal Home Remote System Operation (With One Triangular LED) Your vehicle may have the Universal Home Remote System. If there is one triangular Light Emitting Diode (LED) above the Universal Home Remote buttons, follow the instructions below. If your vehicle has three round LED above the Universal Home Remote buttons, follow the instructions under Universal Home Remote System Operation (With three round LED). Do not use the Universal Home Remote with any garage door opener that does not have the stop and reverse feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow Steps 6 through 8 to complete the programming of your Universal Home Remote Transmitter. Read the instructions completely before attempting to program the Universal Home Remote. Because of the steps involved, it may be helpful to have another person available to assist you in the programming steps. Keep the original hand-held transmitter for use in other vehicles as well as for future Universal Home Remote programming. It is also recommended that upon the sale of the vehicle, the programmed Universal Home Remote buttons should be erased for security purposes. See “Erasing Universal Home Remote Buttons” later in this section or, for assistance, see Customer Assistance Offices on page 482. Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal. 137 Programming Universal Home Remote Follow these steps to program up to three channels: 1. Press and hold down the two outside Universal Home Remote buttons, releasing only when the Universal Home Remote indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third hand-held transmitter to the remaining two Universal Home Remote buttons. 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the Universal Home Remote buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired Universal Home Remote button and the hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 138 4. The indicator light will ﬂash slowly at ﬁrst and then rapidly after Universal Home Remote successfully receives the frequency signal from the hand-held transmitter. Release both buttons. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code equipped device, most commonly, a garage door opener. 6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release it. Immediately press and hold the same button a second time for two seconds, then release it. Immediately, press and hold the same button a third time for two seconds, then release. The Universal Home Remote should now activate your rolling-code equipped device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” You do not want to repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Buick Lacrosse Owners Manual