1994 Buick Century Owners Manual

Trunk Lock

r NOTICE:

Wagon Liftgate Operation The liftgate on your wagon has a liftglass and a liftgate.

Be sure there are no overhead obstructions before you open the liftgate. You could slam the liftgate into something and break the glass.

The door key opens the liftgate and the liftglass.

71

Turn the key to the right to unlatch the liftgate, then pull up on the bottom of the liftgate. To close, pull down on the handle inside the liftgate, then firmly shut the liftgate.

Turn the key to the left to release the liftglass. Then, pull the liftglass up by the handle. To close, lower the liftglass until the latch catches.

72

Glove Box

Use the door key to lock and unlock the glove box. To open, pinch the latch release.

73

Theft Vehicle theft is big business, especially in some cities. Although your Buick has a number of theft deterrent features, we know that nothing we put on it can make it impossible to steal. However, there are ways you can help. Key in the Ignition If you walk away from your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves -- so don’t do it. When you park your Buick and open the driver’s door, you’ll hear a chime reminding you to remove your key from the ignition and take it with you. Always do this. Your steering wheel will be locked, and so will your ignition and transaxle. And remember to lock the doors. Parking at Night Park in a lighted spot, close all windows and lock your vehicle. Remember to keep your valuables out of sight. Put them in a storage area, or take them with you. Parking Lots If you park in a lot where someone will be watching your vehicle, it’s best to lock it up and take your keys.

74

But what if you have to leave your ignition key? What if you have to leave something valuable in your vehicle? 0 Put your valuables in a storage area, like your trunk

or glove box, or rear storage area in the wagon.

0 Lock the glove box. 0 Lock all the doors except the driver’s. 0 Then take the door key with you. New Vehicle “Break-In”

I NOTICE: Don’t drive at any one speed -- fast or slow -- for the first 500 miles (804 km). Don’t

Your modern Buick doesn’t need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines:

make full-throttle starts.

0 Avoid making hard stops for the first 200

miles (322 km) or so. During this time your new brake linings aren’t yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this “breaking-in” guideline every time you get new brake linings.

Ignition Key Positions

C 9.5

With the ignition key in the ignition switch, you can turn the switch to five positions: (A) Accessory: An “on” position in which you can operate your electrical power accessories. Press in the ignition switch as you turn the top of it toward you.

(B) Lock: The only position in which you can remove the key. This locks your steering wheel, ignition and transaxle. (C) Off: Unlocks the steering wheel, ignition, and transaxle, but does not send electrical power to any accessories. Use this position if your vehicle must be pushed or towed, but never try to push-start your vehicle. A warning chime will sound if you open the driver’s door when the ignition is off and the key is in the ignition. (D) Run: An ‘‘on’’ position to which the switch returns after you start your engine and release the switch. The switch stays in the “Run” position when the engine is running. But even when the engine is not running, you can use “Run” to operate your electrical power accessories, and to display some instrument panel warning lights. (E) Start: Starts the engine. When the engine starts, release the key. The ignition switch will return to “Run” for normal driving.

To start your engine: 1. Without pushing the accelerator pedal, turn your

ignition key to “Start.” When the engine starts, let go of the key. The idle speed will go down as your engine gets warm.

NOTICE: Holding your key in “Start” for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor.

NOTICE: If your key seems stuck in “Lock” and you can’t . turn it, be sure it is all the way in. If it is, then turn the steering wheel left and right while you turn the key hard. But turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of this works, then your vehicle needs service.

Starting Your Engine Move your shift lever to “P” (Park) or “N” (Neutral). Your engine won’t start in any other position -- that’s a safety feature. To restart when you’re already moving, use “ N ’ (Neutral) only.

NOTICE: Don’t try to shift to “P” (Park) if your Buick is moving. If you do, you could damage the transaxle. Shift to “P” (Park) only when your vehicle is stopped.

76

2. If your engine won’t start (or starts but then stops), it

could be flooded with too much gasoline. Try pushing your accelerator pedal all the way to the floor and holding it there as you hold the key in “Start” for about three seconds. If the car starts briefly but then stops again, do the same thing, but this time keep the pedal down for five or six seconds. This clears the extra gasoline from the engine.

I NOTICE:

Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the fuel injection system operates. Before adding electrical equipment, check with your dealer. If you don’t, your engine might not perform properly. If you ever have to have your vehicle towed, see the part of this manual that tells how to do it without damaging your vehicle. See “Towing Your Buick” in the Index.

Driving Through Deep Standing Water

I NOTICE:

If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. If you can’t avoid deep puddles or standing water, drive through them very slowly.

77

Engine Coolant Heater (Engine Block Heater) (Canada Only) In very cold weather, 0°F (-18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. To use the coolant heater: 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. 3. Plug it into a normal, grounded 110-volt outlet.

I NOTICE:

After you’ve used the coolant heater, be sure to store the cord as it was before to keep it away from moving engine parts. If you don’t, it could be damaged.

How long should you keep the coolant heater plugged in? The answer depends on the weather, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact a Buick dealer in the area where you’ll be parking your vehicle. The dealer can give you the best advice for that particular area.

78

Automatic Transaxle

There are several different positions for your shift lever. 0 P (Park)

This locks your front wheels. It's the best position to use when you start your engine because your vehicle can't move easily.

79

R (Reverse) Use this gear to back up.

I I NOTICE:

Shifting to “R” (Reverse) while your vehicle is moving forward could damage your transaxle. Shift to “R” only after your vehicle is stopped.

To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see “If You’re Stuck: In Sand, Mud, Ice or Snow” in the Index.

N (Neutral) In this position, your engine doesn’t connect with the wheels. To restart when you’re already moving, use “N” (Neutral) only. Also, use “N” when your vehicle is being towed.

80

I NOTICE:

Damage to your transaxle caused by shifting out of “P” (Park) or “N” (Neutral) with the engine racing isn’t covered by your warranty.

2 (Second Gear) This position gives you more power but lower fuel economy. You can use “2” on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on.

I NOTICE:

Don’t drive in “2” (Second Gear) for more than 5 miles (8 km), or at speeds over 55 mph (88 km/h), or you can damage your transaxle. Use “D” (‘@’’ or “D” if your vehicle has Overdrive) as much as possible. Don’t shift into “2” unless you are going slower than 65 mph (1 05 km/h), or you can damage your engine.

@ Automatic Overdrive If your automatic transaxle has automatic overdrive, this position is for normal driving. If you need more power for passing, and you’re: - Going less than 35 mph (56 km/h), push your

accelerator pedal about halfway down.

- Going about 35 mph (56 km/h) or more, push the

accelerator all the way down.

You’ll shift down to the next gear and have more power.

D (Third Gear) If your automatic transaxle does not have Overdrive, this position is for normal driving, at all speeds, in most street and highway situations. If your automatic transaxle has Overdrive, “D” is like @, but you never go into Overdrive. Here are some times you might choose “D” instead of 0 3 : - When driving on hilly, winding roads - When towing a trailer, so there is less shifting

between gears

- When going down a steep hill

81

c

0 1 (First Gear)

Parking Brake

This position gives you even more power (but lower fuel economy) than “2.” You can use it on very steep hills, or in deep snow or mud. If the selector lever is put in “1,” the transaxle won’t shift into first gear until the vehicle is going slowly enough.

NOTICE: If your front wheels can’t rotate, don’t try to drive. This might happen if you were stuck in very deep sand or mud or were up against a solid object. You could damage your transaxle. Also, if you stop when going uphill, don’t hold your vehicle there with only the accelerator pedal. This could overheat and damage the transaxle. Use your brakes to hold your vehicle in position on a hill.

To set the parking brake: Hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on.

To release the parking brake: Hold the regular brake pedal down. Pull the brake release lever.

Steering Column Shift Lever

I NOTICE:

Driving with the parking brake on can cause your rear brakes to overheat. You may have to replace them, and you could also damage other parts of your vehicle.

If you are towing a trailer and are parking on any hill: See “Towing a Trailer” in the Index. That section shows what to do first to keep the trailer from moving. Shifting Into ‘‘P” (Park) A CAUTION:

1. Hold the brake pedal down with your right foot and

set the parking brake.

2. Move the shift lever into “P” (Park) position like

this: 0 Pull the lever toward you.

83

Leaving Your Vehicle With the Engine Running

0 Move the lever up as far as it will go.

3. Move the ignition key to “Lock.” 4. Remove the key and take it with you. If you can

walk away from your vehicle with the ignition key in your hand, your vehicle is in “P’, (Park).

If you have to leave your vehicle with the engine running, be sure your vehicle is in “P’, (Park) and your ‘parking brake is firmly set before you leave it. After you’ve moved the shift lever into the “P,’ (Park) position, hold the regular brake pedal down. Then, see if you can move the shift lever away from “P” (Park) without first pulling it toward you. If you can, it means that the shift lever wasn’t fully locked into “P” (Park).

Parking Over Things That Burn

Torque Lock If you are parking on a hill and you don’t shift your transaxle into “P’ (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may find it difficult to pull the shift lever out of “P’ (Park). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into “P” (Park) properly before you leave the driver’s seat. To find out how, see “Shifting Into ‘P’ (Park)” in the Index. When you are ready to drive, move the shift lever out of “P’ (Park) BEFORE you release the parking brake. If “torque lock” does occur, you may need to have another vehicle push yours a little uphill to take some of the pressure from the transaxle, so you can pull the shift lever out of “P” (Park).

85

Engine Exhaust

Running Your Engine While You’re Parked It’s better not to park with the engine running. But if you ever have to, here are some things to know.

I A CAUTION:

86

Follow the proper steps to be sure your vehicle won’t move. See “Shifting Into ‘P’ (Park)” in the Index. If you are parking on a hill and if you’re pulling a trailer, also see “Towing a Trailer” in the Index.

Windows On a vehicle with manual windows, use the window crank to open and close each window. Power Windows (Option)

With power windows, switches on the driver’s armrest control each of the windows when the ignition is on. In addition, each passenger door has a control switch for its own window.

87

Wagon Rear Vent Windows (Option)

Tilt Wheel

A tilt steering wheel allows you to adjust the steering wheel before you drive.

You can also raise it to the highest level to give y6ur legs more room when you exit and enter the vehicle. To tilt the wheel, hold the steering wheel and pull the lever. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place.

To open, pull the latch forward, then push on the center of the latch to swing the window out into the open position. To close the window, pull the center of the latch and then press the latch into the closed position. Horn You can sound the horn by pressing the horn symbol on your steering wheel.

88

Turn SignallHeadlight Beam Lever

Turn Signal and Lane Change Indicator

.1

The lever on the left side of the steering column includes your:

Turn Signal and Lane Change Indicator

0 Headlight High-Low Beam & Passing Signal a Windshield Wipers 0 Windshield Washer

Cruise Control (Option)

The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.

89

Operation of Lights Although your vehicle’s lighting system (headlights, parking lights, fog lamps, side marker lights and taillights) meets all applicable federal lighting requirements, certain states and provinces may apply their own lighting regulations that may require special attention before you operate these lights. For example, some jurisdictions may require that you operate your fog lamps only when your lower beam headlights are also on, or that headlights be turned on whenever you must use your windshield wipers. In addition, most jurisdictions prohibit driving solely with parking lights, especially at dawn or dusk. It is recommended that you check with your own state or provincial highway authority for applicable lighting regulations.

I A green arrow on the instrument panel will flash in the direction of the turn or lane change. To signal a lane change, just raise or lower the lever until the green arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it.

As you signal a turn or a lane change, if the arrows don’t flash but just stay on, a signal bulb may be burned out and other drivers won’t see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the green arrows don’t go on at all when you signal a turn, check the fuse (see “Fuses” in the Index) and for burned-out bulbs. n r n Signal Reminder If your turn signal is left on for more than 3/4 of a mile, a chime will sound. To turn off the chime, move the turn signal lever to the off position.

90

Headlight High-Low Beam

Windshield Wipers

To change the headlights from low beam to high or high to low, pull the turn signal lever all the way toward you. Then release it. When the high beams are on, this blue light on the instrument panel also will be on.

BRIGHT

You control the windshield wipers by turning the band marked “WIPER.” For a single wiping cycle, turn the band to “MIST.” Hold it there until the wipers start, then let go. The wipers will stop after one cycle. If you want more cycles, hold the band on “MIST” longer.

91

You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to “LO,” the shorter the delay. For steady wiping at low speed, turn the band away from you to the “LO” position. For high speed wiping, turn the band further, to “HI.” To stop the wipers, move the band to “OFF.” Remember that damaged wiper blades may prevent you from seeing well enough to drive safely. To avoid damage, be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, carefully loosen or thaw them. If your blades do become damaged, get new blades or blade inserts. Heavy snow or ice can overload your wiper motor. A circuit breaker will stop the motor until it cools. Clear away snow or ice to prevent an overload.

Windshield Washer At the top of the turn signalheadlight beam lever there’s a paddle with the word “PUSH” on it. To spray washer fluid on the windshield, push the paddle. If you push the paddle less than one second, washer fluid will spray three to four times while the wiper blades cycle. If you push the paddle longer than one second, washer fluid will spray as long as the paddle is held. When you release the paddle, the wiper blades will cycle three to four more times to clear the window and then either stop or return to your preset speed. Driving without washer fluid can be dangerous. A bad mud splash can block your vision. You could hit another vehicle or go off the road. Check your washer fluid level often.

92

NOTICE:

Wagon Rear Window Washedwiper (Option)

When using concentrated washer fluid, follow the manufacturer’s instructions for adding water.

a Don’t mix water with ready-to-use washer

fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system. Also, water doesn’t clean as well as washer fluid.

0 Fill your washer fluid tank only 3/4 full

when it’s very cold. This allows for expansion, which could damage the tank if it is completely full. Don’t use radiator antifreeze in your windshield washer. It can damage your washer system and paint.

The rear window washer/wiper switch is at the center of the instrument panel. Press the top of the switch labeled “WASH” and the rear wiper will run at a constant speed.

Press the switch further and hold to spray washer fluid while the wiper continues to run. The wiper will continue to run until you press the switch to “OFF.” The rear window washer fluid reservoir is the smaller reservoir next to the coolant reservoir.

93

Cruise Control (Option)

With Cruise Control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise Control does not work at speeds below about 25 mph (40 km/h). When you apply your brakes, the Cruise Control shuts off.

94

To Set Cruise Control

2. Get up to the speed you want.

1. Move the Cruise

Control switch to “ON.”

3. Push in the “SET”

button at the end of the lever and release it.

4.

5.

The CRUISE light on the instrument panel will come on. Take your foot off the accelerator pedal.

CRUISE

95

To Resume a Set Speed Suppose you set your Cruise Control at a desired speed and then you apply the brake. This, of course, shuts off the Cruise Control. But you don’t need to reset it.

Once you’re going about 25 mph (40 h/h) or more, you can move the Cruise Control switch from “ON” to “R/A” (Resume/Accelerate) for about half a second.

To Increase Speed While Using Cruise Control There are two ways to go to a higher speed. Here’s the first: 1. Use the accelerator pedal to get to the higher speed. 2. Push the SET button at

the end of the lever, then release the button and the accelerator pedal. You’ll now cruise at the higher speed.

You’ll go right back up to your chosen speed and stay there. <

Remember, if you hold the switch at “R/A” longer than half a second, the vehicle will keep going faster until you release the switch or apply the brake. You could be startled and even lose control. So unless you want to go faster, don’t hold the switch at “R/A.”

96

Here’s the second way to go to a higher speed: 1. Move the Cruise switch

from “ON” to “R/A.” Hold it there until you get up to the speed you want, and then release the switch.

2. To increase your speed in very small amounts, move

the switch to “R/A” for less than half a second and then release it. Each time you do this, your vehicle will go 1 mph (1.6 km/h) faster. If you tap “R/A” five times, you will go 5 mph faster.

The accelerate feature will only work after you have set the Cruise Control speed by pushing the SET button. To Reduce Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control:

Push in the SET button at the end of the lever until you reach the lower speed you want, then release it.

2. To slow down in very small amounts, push the

button for less than half a second. Each time you do this, you’ll go 1 mph (1.6 km/h) slower. If you tap SET five times, you will go 5 mph slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the Cruise Control speed you set earlier. Using Cruise Control on Hills How well your Cruise Control will work on hills depends upon your speed, load, and the steepness of the hills. -When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of Cruise Control. Many drivers find this to be too much trouble and don’t use Cruise Control on steep hills.

97

To Get Out of Cruise Control

There are two ways to turn off the Cruise Control: 1. Step lightly on the brake

pedal, OR

Lights

These switches control the following light systems:

Headlights Parking Lights Side Marker Lights Taillights License Plate Lights Instrument Panel Lights

2. Move the Cruise switch

to “OFF.”

To turn on the headlights, press the switch with the light symbol. Press the switch marked “P’ to turn on the parking lights. Press “OFF” to turn off all lights.

To Erase Speed Memory When you turn off the Cruise Control or the ignition, your Cruise Control set speed memory is erased. 98

Interior/Instrument Panel Lights

You can brighten or dim the instrument panel lights by rotating the control up or down. To turn on the interior courtesy lights, rotate the control all the way up to “HI.”

Headlight ccOn99 Warning If you open the door while leaving the lights on, you will hear a warning chime.

Daytime Running Lights (Canada Only) The Canadian Federal Government has decided that “Daytime Running Lights” (DRL) are a useful feature, in that DRL can make your vehicle more visible to pedestrians and other drivers during daylight hours. DRL are required on new vehicles sold in Canada. Your DRL work with a light sensor on top of the instrument panel. Don’t cover it up. The low beam headlights will come on at reduced brightness in daylight when: 0 the ignition is on, 0 the headlight switch is off, and 0 the parking brake is released. At dusk, the exterior lights will come on automatically and the low beams will change to full brightness. At dawn, the exterior lights will go out and the low beams will change to the reduced brightness of DRL (if the headlight switch is off).

99

Of course, you may still turn on the headlights any time you need to. To idle your vehicle with the DRL off, set the parking brake while the ignition is in the “Off’ or “Lock” position. Then start the vehicle. The DRL will stay off until you release the parking brake.

Front Seat Reading Lights (Option)

, ..

Press the switch to turn the map light on and off.

Press the switch to turn the front seat reading lights on or off.

100

Rear Reading Lights (Wagon)

Press the switches on the front of the mirror to turn on the reading lights.

This light will go on when you open the liftgate. To turn on the light when the liftgate is closed, press the switch.

1 A1

Mirrors Inside Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind you car. The day-night adjustment allows you to reduce glare from lights behind you, pull the lever toward you to the night position.

Interior Lights Delay When you pull on the driver’s outside door handle, the dome and courtesy lights will go on and stay on for about 40 seconds, or until you turn the ignition on. If you pull on the driver’s inside door handle within 30 seconds of switching off the ignition, the interior lights will go on and stay on for about 5 seconds, to allow you to unlock your door(s). Courtesy Lights When any door is opened, several lights go on. These lights are under the instrument panel. Optional lights are on the rear doors. They make it easy for you to enter and leave the vehicle. You also can turn these lights on by rotating the interior lights switch to “HI.”

1 A 3

Outside Mirrors Manual Both the driver and passenger side outside mirrors should be adjusted so that you just see the side of your vehicle and the area behind your vehicle when you are sitting in a comfortable driving position.

Use the remote control knob on the driver’s door to adjust the driver’s outside mirror. Adjust the passenger’s outside mirror by hand.

Power (Option) Both the driver’s and optional passenger side outside mirrors can be adjusted with the control lever on the driver’s door.

Turn the knob left or right to select the driver’s or passenger’s mirror. Rotate !!!!!!! the knob to adjust the

mirror. Adjust each mirror so that you can just see the side of your vehicle and the area behind your vehicle when you are sitting in a comfortable driving position.

103

Convex Outside Mirror Your right side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat.

Lighted Visor Vanity Mirror (Option)

If your vehicle has the optional lighted vanity mirror, the lights come on when you open the cover. Close the cover to turn out the lights.

104

Convenience Net (Option)

Wagon Cargo Security Cover (Option) This cover is designed to help conceal articles in the rear storage area. It pulls out and retracts like a window shade. If you have the optional rear-facing third seat, make sure it is folded down.

Your vehicle may have a convenience net. You’ll see it just inside the back wall of the trunk. Put small loads, like grocery bags, behind the net. It can help keep them from falling over during sharp turns or quick starts and stops. The net isn’t for larger, heavier loads. Store them in the trunk as far forward as you can. You can unhook the net so that it will lie flat when you’re not using it.

To Use the Cover: Grasp the handle and pull the cover over the rear storage area. Insert the ends of the support rod into the slots in the trim panel near the liftgate. When the cover isn’t in use, roll it back onto the roller. Hold the handle and lift the support rod out of the slots. Tug the cover lightly, then let it roll back automatically. Don’t release the handle until the cover has rolled back completely.

To Remove the Cover: You can remove the cover and roller assembly for extra cargo room. Slide back the end sleeve and lift the assembly out of the notch in the trim panel. To replace the assembly, reverse the procedure. Luggage Carrier (Option) If you have the optional luggage carrier, you can load things on top of a wagon, or on the deck lid of your vehicle. The luggage carrier has slats attached to the deck lid, a rear rail, and tiedowns. The wagon has slats attached to the roof, side rails, and adjustable crossrails.

106

The crossrails can be adjusted by loosening the screws. After moving the crossrails, be sure to tighten the screws securely.

Storage Armrest (Option)

I I NOTICE:

Loading cargo that weighs more than 50 pounds (23 kg) for the deck lid or 200 pounds (90 kg) for the roof on the luggage carrier may damage your vehicle. When you carry large things, never let them hang over the rear or the sides of your vehicle. Load your cargo so that it rests on the slats and does not scratch or damage the vehicle. Put the cargo against the rear rail of the deck lid carrier and fasten it securely. On the wagon, put the cargo against the side rails of the roof carrier and fasten it securely.

Don’t exceed the maximum vehicle capacity when loading your Buick. For more information on vehicle capacity and loading, see “Loading Your Vehicle” in the Index. To prevent damage or loss of cargo as you’re driving, check now and then to make sure the luggage carrier and cargo are still securely fastened.

The front armrest opens into a storage area. To open it, lift the lever at the front edge. Inside is a coin holder, slots to hold cassettes or CDs and a dual cup holder. To use the cup holder, flip it forward and close the armrest cover. The cup holder can be removed for cleaning. Flip the cup holder into the armrest storage area. Squeeze the arms inward to release the retainer pins. Remove the cup holder.

107

The armrest can be raised so that a passenger can sit in the center position. Rear Locking Storage Compartment (Wagon)

Ashtrays

Reach under the front edge of the ashtray compartment to open it. To remove the ashtray for cleaning, reach under the ashtray and push up from behind it.

Use your door key to unlock the storage bin on the driver’s side near the liftgate.

108

Cigarette Lighter To use the lighter, push it in all the way and let go. When it’s ready, it will pop back by itself.

NOTICE: Don’t hold a cigarette lighter in with your hand while it is heating. If you do, it won’t be able to back away from the heating element when it’s ready. That can make it overheat, damaging the lighter and the heating element.

109

To clean the rear ashtrays, fully open the ashtray. Press down on the snuffer as you pull the ashtray down and out.

I NOTICE:

Don’t put papers and other things that burn into ashtrays. If you do, cigarettes or other smoking materials could set them on fire, causing damage.

Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the U.S.) or kilometers (used in Canada). Your Buick has a “tamper-resistant odometer.” If you can see very noticeable bright silver lines between the numbers, probably someone has tried to turn it back. The numbers may not be true. You may wonder what happens if a vehicle has to have a new odometer installed. If possible, the new one has to be set to the same reading as the old one. If it can’t be, then it’s set at zero, and a label on the driver’s door must show the old reading and when the new one was installed.

The Instrument Panel: Your Information System

Your instrument panel is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically.

110

Trip Odometer

The trip odometer can tell you how many miles you have driven since you last set it to zero. To reset it, push the button.

Warning Lights, Gages and Indicators This section describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an

expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights go on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on briefly when you turn the ignition key just to let you know they’re working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there’s a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow the manual’s advice. Waiting to do repairs can be costly -- and even

111

dangerous. So please get to know your warning lights and gages. They’re a big help. Fuel Gage

I Your fuel gage tells

you about how much fuel you have left, when the ignition is on. When the indicator nears “E” (Empty), you still have a little fuel left, but you should get more soon.

Here are four things that some owners ask about. None of these show a problem with your fuel gage and are normal operating characteristics:

At the service station, the gas pump shuts off before the gage reads “F” (Full). It takes a little more or less fuel to fill up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to fill the tank. The gage moves a little when you turn a corner, speed up or brake. The gage doesn’t go back to “E” when you turn off the ignition.

112

Brake System Warning Light

If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is Your Buick’s hydraulic harder to push. Or, the pedal may go closer to the floor. brake system is divided into It may take longer to stop. If the light is still on, or if the two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well.

anti-lock brake system warning light is flashing, have the vehicle towed for service. (See “Anti-Lock Brake System Warning Light” and “Towing Your Buick” in the Index.)

BRAKE

If the warning light comes on, there cou Ild be a brake problem. Have your brake system inspected right away. This light should come on as you start the vehicle. If it doesn’t come on then, have it fixed so it will be ready to warn you if there’s a problem.

The brake system warning light will also come on when you set your parking brake, and it will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.

113

I

Anti-Lock Brake SJ

‘S tern Warning’Light

ANTI- LOCK

With anti-lock, this light will come on when you start your engine and it will stay on for three seconds. That’s normal. If the light doesn’t come on, have it fixed so it will be ready to warn you if there is a problem.

If the light flashes when you’re driving, you don’t have anti-lock brakes and there’s a problem with your regular brakes. Pull off the road and stop carefully. You may notice that the pedal is harder to push. Or, the pedal may go closer to the floor. It may take longer to stop. Have the vehicle towed for service. (See “Towing Your Buick” in the Index.)

If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off. Or, if the light comes on and stays on when you’re driving, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while you’re driving, your Buick needs service. If the light is on but not flashing and the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes.

114

Anti-Lock Brake System Active Light

LOW

TRACTION

When your anti-lock system is adjusting brake pressure to help avoid a braking skid, the “LOW TRACTION’ light will come on.

Slippery road conditions will exist if this light comes on, so adjust your driving accordingly. The light will stay on for a few seconds after the system stops adjusting brake pressure. The “LOW TRACTION” light also comes on briefly, as a bulb check, when the engine is started.

Engine Coolant Temperature Warning Light

F-

4ccN

TEMP

This light tells you that your engine coolant has overheated or your radiator cooling fan is not working. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn the engine off as soon as possible.

The chapter “Problems on the Road,” in this manual explains what to do. See “Engine Overheating” in the Index.

Malfunction Indicator Lamp (Service Engine Soon Light)

SERVICE ENGINE SOON

A computer monitors operation of your fuel, ignition and emission control systems. This light should come on when the ignition is on, but the engine is not running, as a check to show you it is working.

If it does not come on at all, have it fixed right away. If it stays on, or it comes on while you are driving, the computer is indicating that you have a problem. You should take your vehicle in for service soon.

Engine Coolant Temperature Gage

This gage shows the engine coolant temperature. If the gage pointer moves into the red area, your engine is too hot!

260 i

100

-E- \ \ T lm, TEMPERATURE

That reading means the same thing as the warning light. It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. The chapter “Problems on the Road,” in this manual explains what to do. See “Engine Overheating” in the Index.

116

I NOTICE:

If you keep driving your vehicle with this light on, after a while the emission controls won’t work as well, your fuel economy won’t be as good and your engine may not run as smoothly. This could lead to costly repairs not covered by your warranty.

Engine Oil Pressure Light

OIL

If you have a problem with your oil, this light may stay on after you start your engine, or come on when you are driving. Stop your car and shut off the engine if this light stays on. This indicates that oil is not going through your engine quickly enough to keep it lubricated.

The engine could be low on oil, or could have some other oil problem. Have.your vehicle serviced immediately. The oil light could also come on in three other situations:

When the ignition is on but the engine is not running, the light will come on as a test to show you it is working, but the light will go out when you turn the ignition to “Start.” If it doesn’t come on with the ignition on, you may have a problem with the fuse or bulb. Have it fixed right away. Sometimes when the engine is idling at a stop, the light may blink on and off. This is normal. If you make a hard stop, the light may come on for a moment. This is normal.

117

NOTICE: Damage to your engine from neglected oil problems can be costly and is not covered by your warranty.

Battery Light

The battery warning light will come on briefly when you turn on the ignition, but the engine is not running, as a check to show you it is working.

Then it should go out. If it stays on, or corn-es 6n %bile you are driving, you may have a problem with the electrical charging system. It could indicate that you have a loose generator drive belt or another electrical problem. Have it checked right away. Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner.

118

Voltage Indicator

Liftgate Ajar Warning Light (Wagon)

When your engine is not running, but the ignition is on (in the “Run” position), the gage shows your battery’s state of charge in DC volts. When the engine is running, the gage shows the condition of the charging system. Readings between the red warning zones indicate the normal operating range.

The “TAILGATE AJAR” light on your instrument panel will come on if your liftgate is not completely closed.

TAILGATE

AJAR

Readings in either red warning zone indicate a possible problem in the electrical system. Have your vehicle serviced immediately.

119

120

Part 3 Comfort Controls and Audio Systems

In this part you’ll find out how to operate the comfort control systems and audio systems offered with your Buick . Be sure to read about the particular system supplied with your vehicle . Part 3 includes:

Comfort Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airconditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heater and Defroster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RearWindowDefogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Audiosystems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

i22 122 123 123 123 125 Radio Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126. 128. 130 TapePlayerControls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 CDPlayerControls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Care of Cassette Tape Player and Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 CareofCompactDiscs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Power Antenna Mast Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

Your Buick Comfort Control System

The air conditioner and heater work best if you keep your windows closed while using them. Your vehicle also has the flow-through ventilation system described later in this section. Lever Controls: The upper lever changes the functions of your system. The lower lever changes the temperature of the air coming through the system. The lever next to the fan symbol selects the force of air you want. To turn the fan off, move the upper lever to the OFF position.

_ _

Air Conditioning The upper lever has three air conditioner settings. On very hot days, open the windows long enough to let hot inside air escape. This reduces the amount of work your air conditioner's compressor will have to do, which should help fuel economy. MAX: Provides maximum cooling with the least amount of work. This setting recirculates much of the air inside your vehicle so it maximizes your air conditioner's performance and fuel economy. NORM (Normal): Use for normal cooling on hot days. This setting cools outside air and directs it through the instrument panel outlets. BI-LEV (Bi-Level): Use this on cool, but sunny days. This setting brings in the outside air, and directs it in two ways. The cool air is directed to the upper portion of your body through the instrument panel outlets, and warmed air is directed through the heater ducts and defroster vents. At times this temperature difference may be more apparent than others. The air conditioner compressor operates in all Air Conditioning positions, and in Defrost when the outside temperature is above about 40°F (4.5"C).

Ventilation For mild outside temperatures, when little heating or cooling is needed, slide the upper lever to VENT. Air flow is through the instrument panel outlets. Rotate the control next to the outlets to turn on, adjust or turn off the air flow. Adjust the lower lever on the control panel to the temperature desired. Heating When outside temperatures are cold, sliding the upper lever to HEATER and the lower lever to HOT will send heated air through the heater ducts, and some through the defroster vents. VENT and HEATER are labeled ECONOMY positions because the air conditioner compressor doesn't run in these two settings. This reduces engine load, resulting in improved fuel economy. If either setting fails to keep you comfortable, or causes your windows to fog up, slide the upper lever to one of the Air Conditioning positions, or to DEF (Defrost). Defrosting The DEF setting directs most of the air through the defroster vents, and some through the heater ducts.

Defog To quickly defog the windshield, set the upper lever to DEF and move the fan switch to HI . Slide the lower lever to HOT. In damp, cool weather (temperatures about 45 "-65"F, 7"- 1 8"C), you can use BI-LEV to defog the side windows. Set the upper lever to BI-LEV and the fan switch to HI. Aim the side vents toward the side windows. For increased air flow to the side vents, close the center vents. Rear Window Defogger (Option)

The rear window defogger uses a warming grid to remove fog from the rear window. In winter, it can also keep ice from forming on the rear window.

1 3 2

Press the ON portion of the switch. The indicator light will glow. The rear window defogger will turn off automatically after about 10 minutes of use. You can also turn it off by turning off the ignition or pressing the OFF portion of the switch.

I NOTICE:

Don’t use a razor blade or somerning else sharp on the inside of the rear window. If you do, you could cut or damage the warming grid, and the repairs wouldn’t be covered by your warranty.

Flow-Through Ventilation System Your Buick’s flow-through ventilation system supplies outside air into the vehicle when it is moving. Outside air will also enter the vehicle when the heater or the air conditioning fan is running.

Ventilation Tips

Keep the hood and front air inlet free of ice, snow, or any other obstruction (such as leaves). The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. When you enter a vehicle in cold weather, turn the blower fan to HI for a few moments before driving off. This helps clear the intake ducts of snow and moisture, and reduces the chance of fogging the inside of your windows. Keep the air path under the front seats clear of objects. This helps air to circulate throughout your vehicle.

124

Audio Systems Your Delco@ audio system has been designed to operate easily and give years of listening pleasure. But you will get the most enjoyment out of it if you acquaint yourself with it first. Find out what your Delco@ system can do and how to operate all its controls, to be sure you're getting the most out of the advanced engineering that went into it. FM Stereo FM stereo will give you the best sound. But FM signals will reach only about 10 to 40 miles (16 to 65 km). Tall buildings or hills can interfere with FM signals, causing the sound to come and go. AM The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can also pick up noise from things like storms and power lines. Try reducing the treble to lower this noise.

AM Stereo Your Delco@ system may be able to receive C-Quam@ stereo broadcasts. Many AM stations around the country use C-Quam@ to produce stereo, though some do not. (C-Quam@ is a registered trademark of Motorola, Inc.) If your Delco' system can get C-Quam@ signals, your stereo indicator light will come on when you are receiving it. Be aware that hearing damage from loud noise is almost undetectable until it is too late. Your hearing can adapt to higher volumes of sound. Sound that seems normal can be loud and harmful to your hearing. Take precautions by adjusting the volume control on your radio to a safe sound level before your hearing adapts to it.

125

To help avoid hearing loss or damage:

Adjust the volume control to the lowest setting. Increase volume slowly until you hear comfortably and clearly.

NOTICE: vehicle -- like a tape player, CB radio, mobile Before you add any sound equipment to your telephone or two-way radio -- be sure you can

add what you want. If you can, it's very important to do it properly. Added sound equipment may interfere with the operation of your vehicle's engine, Delco@ radio or other systems, and even damage them. And, your vehicle's systems may interfere with the operation of sound equipment that has been added improperly. So, before adding sound equipment, check with your dealer and be sure to check Federal rules covering mobile radio and telephone units.

126

To Play This Radio Power Press PWR to turn the radio on and off when the ignition is on.

Upper Knob Rotate the knob to control the volume. When the ignition is off, press the knob to display the time. Balance The BAL control behind the upper knob adjusts the left/right speaker balance.

Lower Knob Rotate the lower knob to tune in radio stations. Press it to change between the AM and FM bands.

Fade The FADE control behind the lower knob adjusts the front/rear speaker balance.

Treble Slide this lever up to increase treble, or down to decrease it. If a station is weak or noisy, reduce the treble.

Bass Slide this lever up to increase bass, or down to decrease it.

Scan Press the SCAN button to hear each station for a few seconds. Push it again to stop scanning.

Seek rress the SEEK button to go to the next higher station and stay there. Push it again and it will find the next higher station.

Pushbuttons The four pushbuttons let you return to favorite stations. To set the pushbuttons for up to fourteen stations (7 AM and 7 FM: 1. Use the lower knob (TUNE) to tune in the station

you want.

2. Press SET. The SET indicator will appear in the

display.

3. Within 5 seconds, press one of the four pushbuttons.

Whenever you push that button again, the preset station will return.

Up to three more stations may be preset on each band by pressing two pushbuttons that are next to each other, at the same time. 1. Tune in the desired station. 2. Press SET, and within five seconds press any two pushbuttons that are next to each other at the same time. The station will return when the same two pushbuttons are pressed again.

Clock To set the clock, 1. Press the SET button.

127

2. Within 5 seconds, press and hold SCAN until the

correct hour appears on the display.

3. Press and hold SEEK until the correct minute

appears on the display.

...... _.__” .......

........ .”... .. 7

To Play This Radio Power Press PWR to turn the unit on and off when the ignition is on.

Upper Knob The upper knob does these things: 0 Rotate VOL to control the volume. 128

When the ignition is off, press the knob to display the time. When a tape is playing, press the knob t.o hear the other side of the tape.

Balance The BAL control behind the upper knob adjusts the left/right speaker balance.

Lower Knob This knob does two things:

Rotate it to tune in radio stations. Press it to change between the AM and FM bands.

Fade The FADE control behind the lower knob adjusts the front/rear speaker balance.

Treble Slide this lever up to increase treble, or down to decrease it. If a station is weak or noisy, reduce the treble.

Bass Slide this lever up to increase bass, or down to decrease it. Scan Press the SCAN button to hear each station for a few seconds. Push it again to stop scanning.

Seek Press the SEEK button to go to the next higher station and stay there. Push it again and it will find the next higher station.

Pushbuttons The four pushbuttons let you return to favorite stations. To set the pushbuttons for up to fourteen stations (7 AM and 7 FM: 1. Use the lower knob (TUNE) to tune in the station

you want.

2. Press SET. The SET indicator will appear in the

display.

3. Within 5 seconds, press one of the four pushbuttons.

Whenever you push that button again, the preset station will return.

Up to three more stations may be preset on each band by pressing two pushbuttons that are next to each other, at the same time. 1. Tune in the desired station 2. Press SET, and within five seconds press any two pushbuttons that are next to each other at the same time. The station will return when the same two pushbuttons are pressed again.

Clock To set the clock, 1. Press the SET button. 2. Within 5 seconds, press and hold SCAN until the

correct hour appears on the display.

3. Press and hold SEEK until the correct minute

appears on the display.

Dynamic Noise Reduction Press the DNR@ button to select the Dynamic Noise Reduction system that reduces background hiss on AM and FM radio broadcasts, as well as on cassette tapes. You may want to leave it pushed in all the time.

129

To Play a Cassette Tape With the power switch on, insert a tape into the cassette door. Using tapes that are longer than 90 minutes (45 minutes on each side) is not recommended. When the right indicator arrow is lit, selections listed on the bottom side of the cassette are playing. When the left arrow is lit, selections listed on the top side of the cassette are playing. To change sides of the tape, press the upper control knob (VOL ) while the cassette is playing. The tape player automatically begins playing the other side when it reaches the end of the tape.

Fast Forward To rapidly advance the tape, press the button with the arrow pointing in the same direction the tape is playing. To stop fast forward, lightly press the STOP-EJECT button.

Reverse To rapidly reverse the tape, press the button with the arrow pointing in the opposite direction the tape is playing. To stop reverse, lightly press the STOP-EJECT button.

130

Stop-Eject To stop playing a tape, fully press this button. The cassette will eject, and the radio will begin playing.

To Play This Radio Power Press PWR to turn the unit on and off when the ignition is on.

Upper Knob This knob does two things: 0 Rotate VOL slightly to the left or right to control the

volume.

0 Press it to mute the radio or tape player. Press again

to listen.

Balance The BAL control behind the upper knob adjusts the left/right speaker balance.

Lower Knob This knob does two things: 0 Rotate TUNE slightly to the left or right to tune in

radio stations. If you hold it to the left or right, it will tune rapidly.

0 Press to change between the AM and FM bands. The

band you select will appear on the digital display.

Fade The FADE control behind the lower knob adjusts the front/rear speaker balance.

Scan Press the SCAN button to hear each station for a few seconds. Push it again to stop scanning.

Seek Press the SEEK button to go to the next higher station and stay there. Push it again and it will find the next higher station.

Recall Press RCL to alternate the display between the time and station frequency. When the ignition is off, press to display the time.

Bass Press BASS up or down to increase or decrease the bass level. Press the center of the button for the factory preset level.

Treble Press TREB up or down to increase or decrease the treble level. Press the center of the button for the factory preset level. If a station is weak or noisy, reduce the treble.

131

Pushbuttons The five pushbuttons let you return to favorite stations. 1. Use the lower knob (TUNE) to tune in the station

you want.

2. Press SET. The SET indicator will appear in the

display.

3. Within 5 seconds, press one of the five pushbuttons.

Whenever you push that button again, the preset station will return.

Clock To set the clock, 1. Press the SET button. 2. Within 5 seconds, press and hold SCAN until the

correct hour appears on the display.

3. Press and hold SEEK until the correct minute

appears on the display.

To Play a Compact Disc: Before you begin, please note: Don’t use mini-discs that are called singles. They won’t eject. Use only full-size compact discs. 1. Press PWR to turn the radio on. 132

2. Insert a disc part-way into the slot, with the label

side up. The player will pull it in. In a few seconds, the disc should play.

If the disc comes back out and/or Err appears on the display: 0 The disc may be upside down. 0 The disc may be dirty, scratched or wet.

There may be too much moisture in the air (wait about one hour and try again). The player may be too hot, or the road may be too rough for the disc to play. As soon as things get back to normal, the disc should play.

While a disc is playing, the CD indicator is displayed.

Recall Press RCL once to see which track is playing. Press again within five seconds to see how long your selection has been playing. The track number also will be displayed when the volume is changed or a new track starts to play.

Compression Depressing COMP makes soft and loud passages more equal in volume. Press again to resume normal play.

Random Press RDM to play tracks in random, rather than sequential, order. Press the button again to play tracks sequentially.

Scan Press SCAN to play each track for approximately ten seconds. Scan will continue until SCAN is pressed again or another button is pressed.

Reverse Press REV and hold to rapidly back up to a favorite passage. Release to resume playing.

Fast Forward Press FWD and hold to rapidly advance the disc. Release to resume playing.

Previous Press PREV to play a track again. If you hold or keep pressing the PREV button, the disc will keep backing up to previous tracks.

Next Press NEXT when you want to hear the next track. If you hold or keep pressing the NEXT button, the disc will keep advancing to other tracks.

Stop/Play Press STPL to stop the disc player; the radio will play. Press again to play the disc (the player will start playing the disc where it was stopped earlier).

Eject Press EJCT to eject the disc; the radio will play. You can also eject the disc with the radio or ignition off. If you press PWR or turn off the ignition, the disc will stay in the player and start again when you turn on the ignition or power switch. The disc will begin playing at the point where it had been stopped.

133

CD Player Anti-Theft Feature Delco LOC I1 is a security feature for the compact disc player. It can be used or ignored. If ignored, the system plays normally. If it is used, your player won’t be usable if it is ever stolen, because it will go to LOC mode any time battery power is removed. Until an unlock code is entered, it will not turn on. The instructions below tell you how to enter a secret code into the system. If your vehicle loses battery power for any reason, you must unlock the system with the secret code before the radio will turn on. Be sure to read through the entire procedure and become familiar with the appropriate buttons and knobs before starting. 1. Write down any six-digit number and keep it in a

safe place.

2. Turn the ignition to the ACC or RUN position. 3. Press the PWR button to turn the radio off. 4. Press the 1 and 4 pushbuttons together. Hold them

down until “---” shows on the display. You are ready to enter your secret code. If you pause more than 15 seconds between steps, you may have to start the procedure over.

134

5. Press SET and “000” will appear on the display. 6. Press the SEEK button to make the first number

appear.

7. Rotate the TUNE knob right or left to make the last

two numbers agree with your code.

8. Press the lower (BAND) knob and “000” will appear

again. Now you are ready to enter the last three digits of your code by repeating steps 6 and 7 for the last three digits of your code.

9. Press the lower (BAND) knob and “rEP” will appear

for five seconds and then “000” will appear indicating that some steps are to be repeated.

10. Repeat steps 6,7 and 8. 11. Press the lower (BAND) knob. If the display shows

“SEC” it indicates that the process was successful and the radio is secure. If the display shows “---,” the steps were not successful and the process must be repeated to secure.

To Unlock the System After a Power Loss When battery power is reapplied to a secured radio, the radio won’t turn on and “LOC” will appear on the display. Enter your secret code as follows; pause no more than 15 seconds between steps. 1. Turn the ignition on. (Radio off.) 2. Press the SET button. The display will show “000.” 3. Enter the six digits of your code following steps 6-9 on the preceding. The display will show the numbers as entered.

4. Press the lower (BAND) knob and SEC appears,

then the time, indicating that the disabling sequence was successful.

Disabling the Anti-Theft System: 1.

2. 3.

4.

5.

6.

Press the I and 4 buttons together for five seconds with ignition on and radio power off. The display will show “SEC,” indicating the unit is in the secure mode. Press the SET button. The display will show “OOO.” Enter the first three digits of your code following step 6 and 7of the preceding paragraphs. The display will show the numbers as entered. Press the lower (BAND) knob. The radio will display “000.” Enter the second three digits of the code. The display will show the numbers as entered. Press the lower (BAND) knob. If the display shows “--- , ” the disabling sequence was successful (the numbers matched the user-selected code or the factory back-up code) and the unit is in the UNSECURED mode. If the display shows “SEC,” the disabling sequence was unsuccessful and the numbers did not match either of the codes and the unit will remain in the SECURED mode.

135

Care of Your Cassette Tape Player

A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes, or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight, and extreme heat. If they aren't, they may not operate properly or cause failure of the tape player. Your tape player should be cleaned regularly each month or after every 15 hours of use. If you notice a reduction in sound quality, try a known good cassette to see if the tape or the tape player is at fault. If this other cassette has no improvement in sound quality, clean the tape player.

136

Clean your tape player with a wiping-action, non-abrasive cleaning cassette, and follow the directions provided with it. Cassettes are subject to wear and the sound quality may degrade over time. Always make sure that the cassette tape is in good condition before you have your tape player serviced. Care of Your Compact Discs Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping only from the center to the edge. Be sure never to touch the signal surface when handling discs. Pick up discs by grasping the outer edges or the edge of the hole and the outer edge. Fixed Mast Antenna The fixed mast antenna can withstand most car washes without being damaged. If the mast should ever become slightly bent, you can straighten it out by hand. If the mast is badly bent, as it might be by vandals, you should replace it. Check every once in a while to be sure the mast is still tightened to the fender.

Power Antenna Mast Care

Your power antenna will look its best and work well if it’s cleaned from time to time.

To Clean the Antenna Mast: 1. Turn on the ignition and radio to raise the antenna to

full mast extension.

2. Dampen a clean cloth with mineral spirits or

equivalent solvent.

3. Wipe cloth over the mast sections, removing any dirt.

4. Wipe dry with clean cloth before retracting. 5. Make the antenna go up and down by turning the

radio or ignition on and off.

6. Then repeat if necessary.

NOTICE: Don’t lubricate the power antenna. Lubrication could damage it.

NOTICE: Before entering an automatic car wash, turn off your radio to make the power antenna go down. This will prevent the mast from possibly getting damaged. If the antenna does not go down when you turn the radio off, it may be damaged or need to be cleaned. In either case, lower the antenna by hand by carefully pressing the antenna down.

137

138

1940 Buick Model 51 G

Part 4 Your Driving and the Road

Here you’ll find information about driving on different kinds of roads and in varying weather conditions . We’ve also included many other useful tips on driving . Part 4 includes:

DefensiveDriving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DrunkenDriving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control of a Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LossofControl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DrivingatNight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DrivingintheRain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CityDriving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FreewayDriving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HillandMountainRoads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WinterDriving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TowingaTrailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

140 140 144 144 147 150 151 152 154 156 157 160 161 165

139

Assume that pedestrians or other drivers are going to be careless and make mistakes. Anticipate what they might do. Be ready for their mistakes. -. Rear-end collisions are about the most preventable of accidents. Yet they are common. Allow enough following distance. It’s the best defensive driving maneuver, in both city and rural driving. You never know when the vehicle in front of you is going to brake or turn suddenly.

Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It’s the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol takes away three things that anyone needs to drive a vehicle:

Judgment

0 Muscular Coordination

Vision

Police records show that almost half of all motor vehicle-related deaths involve alcohol - a driver, a passenger or someone else, such as a pedestrian, had

Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your Buick: Buckle up. (See “Safety Belts” in the Index.) Defensive driving really means “be ready for anything.” On city streets, rural roads, or freeways, it means “always expect the unexpected.” 140

been drinking. In most cases, these deaths are the result of someone who was drinking and driving. About 20,000 motor vehicle-related deaths occur each year because of alcohol, and thousands of people are injured. Just how much alcohol is too much if a person plans to drive? Ideally, no one should drink alcohol and then drive. But if one does, then what’s “too much”? It can be a lot less than many might think. Although it depends on each person and situation, here is some general information on the problem. The Blood Alcohol Content (BAC) of someone who is drinking depends upon four things:

How much alcohol is in the drink.

0 The drinker’s body weight. 0 The amount of food that is consumed before and

during drinking. The length of time i t has taken the drinker to consume the alcohol.

According to the American Medical Association, a 180-pound (82 kg) person who drinks three 12-ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4-ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of a liquor like whiskey, gin or vodka.

1 A 1

It’s the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a slightly lower BAC level.

RESULT IN A BAC nr 95%

DRINKING THAT WILL IN THE TIM Sl., ...l

NUMBER OF DRINKS (as in plcture)

’ HOURS

HOURS

HOUR

100 120 140 160 180 200 220 240

BODY WEIGHT IN POUNDS

The law in most U.S. states sets the legal limit at a BAC of 0.10 percent. In Canada the limit is 0.08 percent, and in some other countries it’s lower than that. The BAC will be over 0.10 percent after three to six drinks (in one hour). Of course, as we’ve seen, it depends on how much alcohol is in the drinks, and how quickly the person drinks them. But it’s very important to keep in mind that the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent. Statistics show that the chance of being in an accident increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent (three beers in one hour for a 180-pound or 82 kg person) has doubled his or her chance of having an accident. At a BAC level of 0.10 percent, the chance of that driver having an accident is six times greater; at a level of 0.15 percent, the chances are twenty-five times greater! And, the body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up.

A CAUTION:

“I‘ll be careful” isn’t the right answer. What if there’s an emergency, a need to take sudden action, as when a child darts into the street? A person with a higher BAC might not be able to react quickly enough to avoid the collision. There’s something else about drinking and driving that many people don’t know. Medical research shows that alcohol in a person’s system can make crash injuries worse. That’s especially true for brain, spinal cord and heart injuries. That means that if anyone who has been drinking -- driver or passenger -- is in a crash, the chance of being killed or permanently disabled is higher than if that person had not been drinking. And we’ve already seen that the chance of a crash itself is higher for drinking drivers.

143

Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road.

Sometimes, as when you’re driving on snow or ice, it’s easy to ask more of those control systems than the tires and road can provide. That means you can lose control of your vehicle. Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That’s perception time. Then you have to bring up your foot and do it. That’s reaction time. Average reaction time is about 3/4 of a second. But that’s only an average. It might be less with one driver and as long as two or three seconds or more with another. Age, physical condition, alertness, coordination, and eyesight all play a part. So do alcohol, drugs and frustration. But even in 3/4 of a second, a vehicle moving at 60 mph (100 km/h) travels 66 feet (20 m). That could be a lot of distance in an emergency, so keeping enough space between your vehicle and others is important.

144

And, of course, actual stopping distances vary greatly with the surface of the road (whether it’s pavement or gravel); the condition of the road (wet, dry, icy); tire tread; and the condition of your brakes. Avoid needless heavy braking. Some people drive in spurts -- heavy acceleration followed by heavy braking -- rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life. If your engine ever stops while you’re driving, brake normally but don’t pump your brakes. If you do, the pedal may get harder to push down. If your engine stops, you will still have some power brake assist. But you will use it when you brake. Once the power assist is used up, it may take longer to stop and the brake pedal will be harder to push.

Anti-Lock Brakes (ABS) Your Buick has an advanced electronic braking system that will help prevent skidding.

This light on the