68
31TL1620.indb 68
• Goes off if a door or the trunk is
closed.
• Stays on constantly or does not come on at all - Have the vehicle checked by a dealer.
Î If the EPS Indicator Comes On
P.292
• Comes on during driving - Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.
• Blinks and remains on - Have the
vehicle checked by a dealer. If the vehicle is fitted with a compact spare, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.
2010/09/10 16:12:56
Indicators
Indicator
Name
On/Blinking
Explanation
Message
• Comes on along with a beep when
• While the indicator is on, press the
a problem is detected. A system message on the multi-information display appears at the same time.
System Message Indicator
Turn Signal Indicators
High-Beam Indicator
• The turn signal indicators blink
when you operate the turn signal lever.
• If you press the hazard warning
button, both indicators and all turn signals blink at the same time.
• Comes on when the high beam
headlights are on.
• Comes on with reduced brightness when DRL (daytime running lights) are on.
(information) button to see
the message again.
• Refer to the Indicators information in this chapter when a system message appears on the multi-information display. Take the appropriate action for the message.
• The multi-information display does
not return to the normal screen unless the warning is canceled, or the
button is pressed.
• Does not blink or blinks rapidly- A turn signal light bulb has blown. Change the bulb immediately.
Î Replacing Light Bulbs P.252, 253
—
• Comes on whenever the light
• If you remove the key from the
Lights On Indicator
switch is on, or in AUTO when the exterior lights are on.
ignition switch while the light is on, a chime sounds when the driver's door is opened.
—
—
—
—
31TL1620.indb 69
Continued
69
2010/09/10 16:12:57
Indicators
Indicator
Name
On/Blinking
Explanation
Message
Fog Light Indicator
• Comes on when the fog lights are
on.
—
U.S.
Canada
Side Airbag Off Indicator
• Comes on for a few seconds when you turn the ignition switch to ON II , then goes off.
• Comes on when the passenger
side airbag system is automatically shut off.
• It does not mean there is a problem
with your side airbags.
• Comes on when nobody is sitting in the passenger seat - Have the vehicle checked by a dealer.
• Comes on when someone is sitting
in the seat - Have the passenger sit properly.
• Comes on briefly when you turn
the ignition switch to ON II , then goes off.
• Comes on if the immobilizer
system cannot recognize the key information.
Immobilizer System Indicator
• Blinks - You cannot start the engine. Turn the ignition switch to LOCK 0 , pull the key out, and then insert the key and turn it to ON II again.
• Repeatedly blinks - The system may
be malfunctioning. Have the vehicle checked by a dealer.
• Do not attempt to alter this system or add other devices to it. Electrical problems can occur.
Security System Alarm Indicator
Indicator Indicator
• Blinks when the Security System
Alarm has been set.
Î Security System Alarm P.98
—
U.S.
Canada
—
—
70
31TL1620.indb 70
2010/09/10 16:12:57
Indicators
Indicator
Name
On/Blinking
Explanation
Message
CRUISE MAIN Indicator
CRUISE CONTROL Indicator
• Comes on when you press the
CRUISE button.
Î Cruise Control P.201
• Comes on if you have set a speed
for cruise control.
Î Cruise Control P.201
—
—
71
31TL1620.indb 71
2010/09/10 16:12:58
I
Indicators
Multi-Information Display Warning and Information Messages
Multi-Information Display Warning and Information Messages
The following messages appear only on the multi-information display. Press the again with the system message indicator on.
(information) button to see the message
Message
Condition
Explanation
• Appears when the engine coolant temperature gets
Î Overheating P.288
abnormally high.
• Appears when the fuel fill cap is loose or is not
Î Tighten the Fuel Fill Cap P.291
installed.
• Appears if there is a problem with the DRL system.
• Have your vehicle checked by a dealer.
Î Daytime Running Lights P.107
Canadian models
• Appears when washer fluid gets low.
• Refilling washer fuild.
Î Refilling Window Washer Fluid P.246
72
31TL1620.indb 72
2010/09/10 16:12:58
Indicators
Multi-Information Display Warning and Information Messages
Message
Condition
• Appears when the scheduled maintenance is due soon. • Consequently, "SERVICE DUE NOW" and "SERVICE
PAST DUE" follow.
Explanation
Î Maintenance Minder™ P.225
• Appears when you open the driver's door while the
ignition key is in ACCESSORY I .
• Turn the ignition swtich to LOCK 0 , then
remove the key.
• Appears when the ignition key is turned to ACCESSORY
I from ON II . (The driver's door is closed.)
—
• Appears when you open the driver's door while the
• Remove the key from the ignition switch.
ignition key is in LOCK 0 .
31TL1620.indb 73
Continued
73
2010/09/10 16:12:58
Indicators
Multi-Information Display Warning and Information Messages
Message
6-cylinder models U.S.
Canada
74
31TL1620.indb 74
Condition
Explanation
• Appears when the starter system has a problem.
• As a temporary measure, hold the ignition
switch to START III for up to 15 seconds and start the engine. Have the vehicle checked by a dealer.
2010/09/10 16:12:59
Gauges and Multi-Information Display
Gauges
Gauges include the speedometer, tachometer, fuel gauge, and temperature gauge. They are displayed when the ignition switch is in ON II .
Speedometer
Displays your driving speed in mph (U.S.) or km/h (Canada).
Fuel Gauge
Displays the amount of fuel left in the fuel tank.
Temperature Gauge
Displays the temperature of the engine coolant.
Tachometer
Shows the number of engine revolutions per minute.
Fuel Gauge NOTICE You should refuel when the reading approaches E . Running out of fuel can cause the engine to misfire, damaging the catalytic converter.
The actual amount of remaining fuel may differ from the fuel gauge reading.
Temperature Gauge NOTICE If the engine is in danger of overheating. Driving with the temperature gauge pointer in the upper zone can cause serious engine damage. Pull safely to the side of the road and allow engine temperature to return to normal.
Î
Overheating
P.288
75
31TL1620.indb 75
2010/09/10 16:12:59
Gauges and Multi-Information Display
Multi-Information Display
Multi-Information Display
The multi-information display shows the odometer, trip meter, outside temperature indicator, and other gauges. It also displays important messages such as warnings and other helpful information.
Switching the Display
Press the display.
(information) button or the SEL/RESET button to change the
Trip Computer
HFL*
Button
Engine Oil Life
Trip B
Trip A
SEL/RESET Button
Odometer
Outside Temperature
: Press the button. : Press the SEL/RESET button.
Shown when Bluetooth® HandsFreeLink® is activated.
Tire Pressure for each tire
76
* Not available on all models
31TL1620.indb 76
2010/09/10 16:12:59
Gauges and Multi-Information Display
Multi-Information Display
Odometer
Shows the total number of miles (U.S.) or kilometers (Canada) that your vehicle has accumulated.
Trip Meter
Shows the total number of miles (U.S.) or kilometers (Canada) driven since the last reset. Meters A and B can be used to measure 2 separate trips.
Resetting a trip meter
To reset a trip meter, display it, then press and hold the SEL/RESET button. The trip meter is reset to "0.0".
Trip Meter Switch between trip meter A and trip meter B by pressing the SEL/RESET button.
31TL1620.indb 77
2010/09/10 16:12:59
Continued
77
Gauges and Multi-Information Display
Multi-Information Display
Outside Temperature
Shows the outside temperature in Fahrenheit (U.S.) or Celsius (Canada).
Adjusting the outside temperature display
Adjust the temperature reading up to ±5°F or ±3°C if the temperature reading seems incorrect. Use the multi-information display's customized features to correct the temperature.
Î
Customized Features
P.80
Outside Temperature The temperature sensor is in the front bumper. Road heat and exhaust from another vehicle can affect the temperature reading when your vehicle speed is less than 19 mph (30 km/h).
It may take several minutes for the display to be updated after the temperature reading has stabilized.
Instant Fuel Economy
Shows the instant fuel economy as a bar graph in mpg or l/100 km.
Average Fuel Economy
Shows the estimated average fuel economy of each trip meter in mpg (U.S.) or l/ km (Canada). The display is updated at set intervals. When a trip meter is reset, the average fuel economy is also reset.
Range
Shows the estimated distance you can travel on the fuel remaining. This distance is estimated from the fuel economy of your trips in the past.
Average Fuel Economy
You can choose to reset either Trip A or average
fuel economy A when you refuel.
P.80
Customized Features
Î
78
31TL1620.indb 78
2010/09/10 16:12:59
Gauges and Multi-Information Display
Multi-Information Display
Elapsed Time
The elapsed time display shows the time during one drive cycle.
Elapsed Time You can change the elapsed time reset criteria.
Î
Customized Features
P.80
Average Speed
The display shows the average speed in mph (U.S.) or km/h (Canada) since the last time Trip A was reset.
Engine Oil Life
Shows the remaining oil life and Maintenance Minder™.
Î
Maintenance Minder
™ P.225
Tire Pressure Monitor
Shows each tire's pressure.
Î
Tire Pressure Monitoring System
P.206
Bluetooth® HandsFreeLink®
Shows your paired cell phone's information.
Î
Bluetooth
® HandsFreeLink® P.167
31TL1620.indb 79
2010/09/10 16:12:59
Continued
79
Gauges and Multi-Information Display
Multi-Information Display
Customized Features
Use the multi-information display to customize certain features.
How to customize
Press and hold the in ON II .
button for a few seconds while the ignition switch is
Multi-Information Display: Goes to customize settings.
Customized Features To customize other features, press the button.
Î Î
List of customizable options Example of customization settings
P.82
P.84
Customization is possible when you see the driver's ID ("DRIVER 1" or "DRIVER 2") on the CHG setting screen. The driver's ID indicates which remote transmitter you have used to unlock the driver's door. The customized settings are recalled every time you unlock the driver's door with that remote.
When you customize settings: Automatic Transmission models
Button:
Shift to P
Changes the customize menus and items SEL/RESET button: Enters the selected item
Manual Transmission models Set the parking brake
80
31TL1620.indb 80
2010/09/10 16:13:00
Gauges and Multi-Information Display
Multi-Information Display
Customization flow
Press and hold the
button.
CHG SETTING
SEL/RESET
METER SETUP
SEL/RESET
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP. DISPLAY
TRIP A RESET with REFUEL
ELAPSED TIME RESET
DEFAULT ALL
POSITION SETUP
SEL/RESET
MEMORY POSITION LINK*
EXIT
LIGHTING SETUP
SEL/RESET
DOOR SETUP
SEL/RESET
SEL/RESET
EXIT
INTERIOR LIGHT DIMMING TIME
HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER
* Not available on all models
31TL1620.indb 81
Continued
81
2010/09/10 16:13:00
Gauges and Multi-Information Display
Multi-Information Display
List of customizable options
Setup Group
Customizable Features
Description
Selectable settings
Language Selection
Changes the displayed language.
Adjust Outside Temp. Display
Meter Setup
Adjusts the temperature reading by a few degrees.
English*1, French, Spanish
-5°F ~ ±0°F*1 ~ +5°F (U.S)
-3°C ~ ±0°C*1 ~ +3°C (Canada)
Trip A Reset with Refuel
Sets Trip A and the average fuel economy to reset when you refuel.
ON, OFF*1
Elapsed Time Reset
Changes the resetting conditions of the elapsed time.
IGN OFF*1 , Trip A, Trip B
Position Setup Memory Position Link*
Changes the driver's seat position to a stored setting.
ON*1, OFF
Interior Light Dimming Time
Changes the length of time the interior lights stay on after you close the doors.
60 sec, 30 sec*1, 15 sec
Lighting Setup
Headlight Auto Off Timer
Changes the length of time the exterior lights stay on after you close the driver's door.
60 sec, 30 sec, 15 sec*1, 0 sec
Auto Light Sensitivity
Changes the timing for the headlights to come on.
Max, High, Mid*1, Low, Min
*1: Default Setting
* Not available on all models
82
31TL1620.indb 82
2010/09/10 16:13:00
Gauges and Multi-Information Display
Multi-Information Display
Setup Group
Customizable Features
Description
Selectable settings
Auto Door Lock
Changes the setting for the automatic locking feature.
Auto Door Unlock
Changes the setting for when the doors unlock automatically.
Shift from P (A/T only), With VEH SPD*1, OFF Shift to P *2, IGN Off*3, OFF
Driver Door*1, All Doors
Door Lock Mode
Sets up either the driver's door or all doors to unlock on the first push of the remote.
Door Setup
Keyless Lock Acknowledgment
LOCK/UNLOCK - The exterior lights flash LOCK (2nd push) - The beeper sounds
Driver Door*1
All Doors
ON*1, OFF
Security Relock Timer
Changes the time it takes for the doors to relock and the security system to set after you unlock the vehicle without opening any door.
90 sec, 60 sec, 30 sec*1
Default All
Sets/Cancels all the customized settings as default.
Set, Cancel
*1: Default Setting *2: Default Setting for automatic transmission *3: Default Setting for manual transmission
31TL1620.indb 83
Continued
83
2010/09/10 16:13:00
Gauges and Multi-Information Display
Multi-Information Display
Example for customization settings
The steps for changing the "TRIP A RESET with REFUEL" setting to ON are shown below. The default setting for "TRIP A RESET with REFUEL" is OFF.
1. Press and hold
button until "CHG
SETTING" appears on the display.
2. Press the SEL/RESET button to go into the
"METER SETUP" group.
3. Press the SEL/RESET button again.
"LANGUAGE SELECTION" appears first in the display.
84
31TL1620.indb 84
2010/09/10 16:13:00
Gauges and Multi-Information Display
Multi-Information Display
4. Press the
button until "TRIP A RESET with REFUEL" appears on the display, then press the SEL/RESET button.
The display switches to the "Customization setup" screen, where you can select "ON," "OFF, or" "EXIT."
5. Press the
button and select
"ON," then press the SEL/RESET button.
The "ON" setup screen appears, then the display returns to the "Customization menu" screen.
6. Press the
button until "EXIT"
appears in the display, then press the SEL/ RESET button.
7. Repeat Step 6 until you return to the
normal screen.
85
31TL1620.indb 85
2010/09/10 16:13:01
86
31TL1620.indb 86
2010/09/10 16:13:01
This chapter explains how to operate the various controls necessary for driving.
Controls
Setting the Clock .................................. 88
Locking and Unlocking the Doors
Key Types and Functions ...................... 89
Locking/Unlocking the Doors from the
Outside .............................................. 91
Locking/Unlocking the Doors from the
Inside ................................................ 93
Childproof Door Locks ......................... 94
Auto Door Lock/Unlock ....................... 94
Opening/Closing the Trunk ................. 95
Security System .................................... 98
Immobilizer System .............................. 98
Security System Alarm ......................... 98
Opening and Closing the Windows.. 100
Opening and Closing the
Moonroof .......................................... 103
Operating the Switches Around the
Steering Wheel
Ignition Switch ................................... 104
Turn Signals ....................................... 105
Light Switches .................................... 105
Fog Lights ...........................................107
Daytime Running Lights ......................107
Wipers and Washers .......................... 108
Brightness Control ............................. 109
Rear Defogger/Heated Door Mirror
Button ...............................................110
Driving Position Memory System ......... 111
Adjusting the Steering Wheel .............113
Adjusting the Mirror ...........................114
Interior Rearview Mirror ......................114
Door Mirrors .......................................114
Adjusting the Seats .............................116
Adjusting the Seat Positions ................116
Interior Lights/Interior
Convenience Items ........................... 125
Interior Lights ......................................125
Interior Convenience Items ..................126
Climate Control System ..................... 133
Using Automatic Climate Control ........133
Automatic Climate Control Sensors .....136
87
31TL1620.indb 87
2010/09/10 16:13:01
C
Setting the Clock
Clock Models without navigation system You can adjust the time in the clock display, using the CLOCK button.
Adjusting the Time
Menu Button
1. Press the MENU button. 2. Rotate display.
to select CLOCK ADJUST in the
3. Press 4. Rotate
. CLOCK ADJUST appears.
to select the item you want to adjust (12/24 hour mode, hour, minute). Then press
12/24 Hour Mode
5. Rotate 6. Press
to make the adjustment. to enter your selection. The
display returns to CLOCK ADJUST. Repeat steps 4 to 6 to adjust other items.
7. To enter the selection, Rotate
and
select SET, then press
8. Press the MENU button to go back to the
Hour Setting
Minute Setting
normal display.
Clock You can switch the clock display between 24 hours and 12 hours when in the menu mode.
Selector Knob Icon details Rotate Press
to select.
to enter.
To set the time to the nearest hour: Press and hold the CLOCK button until the clock display begins to blink, then press the 3 (Reset) button.
Depending on the displayed time, the clock sets
forward or backward.
Example:
1:06 will reset to 1:00
1:53 will reset to 2:00
Models with navigation system The clock is automatically updated through the navigation system, so the time does not need to be adjusted.
88
31TL1620.indb 88
2010/09/10 16:13:02
Locking and Unlocking the Doors
Key Types and Functions This vehicle comes with the following keys:
Retractable Master Keys
Panic Button
Trunk Button
Lock Button
Unlock Button
Release Button
Release Button
Press
Use the keys to start and stop the engine, and to lock and unlock all the doors, trunk, and fuel fill door. You can also use the remote transmitter to lock and unlock the doors, trunk, and fuel fill door. Models with a driving position system The seat automatically moves to the preset position when you unlock the door using the remote transmitter on the master key.
Î
Driving Position Memory System
P.111
The master key folds up inside the remote transmitter. 1. Press the release button to release the key
out from the transmitter.
Make sure to fully extend the key.
2. To close the key, press the release button then push the key inside the transmitter until you hear a click.
Key Types and Functions All of the keys have an immobilizer system. The immobilizer system helps to protect against vehicle theft. Î
Immobilizer System
P.98
The keys contain precision electronics. Adhere to the following advice to prevent damage to the electronics: •
Do not leave the keys in direct sunlight, or in locations with high temperature or high humidity. Do not drop the keys or set heavy objects on them. Keep the keys away from liquids. Do not take the keys apart except for replacing the battery.
•
• •
If the circuits in the keys are damaged, the engine may not start, and the remote transmitter may not work. If the keys do not work properly, have them inspected by a dealer.
If the key is not fully extended, the immobilizer system may not work properly, and the engine may not start.
Avoid contact with the key whenever it extends or retracts.
31TL1620.indb 89
2010/09/10 16:13:02
Continued
89
Locking and Unlocking the Doors
Key Types and Functions
Valet Key
Can be used to start and stop the engine, and lock and unlock driver's door.
Valet Key When you need to leave a key with a third party, leave the valet key.
Key Number Tag
Contains a number that you will need if you purchase a replacement key.
Key Number Tag Keep the key number tag separate from the key in a safe place outside of your vehicle. If you wish to purchase an additional key, contact a dealer.
If you lose your key and you cannot start the engine, contact a dealer.
90
31TL1620.indb 90
2010/09/10 16:13:02
Locking and Unlocking the Doors
Locking/Unlocking the Doors from the Outside
Locking/Unlocking the Doors from the Outside
Using the Remote Transmitter
Unlock Button
LED
Lock Button
Locking the doors Press the LOCK button. Once:
Some exterior lights will flash, all the doors, trunk, and fuel fill door will lock, and the security system sets.
Twice (within five seconds after the first push):
A beeper sounds and verifies the security system is set.
Unlocking the doors
Press the UNLOCK button. Once:
Some exterior lights will flash twice, and the driver's door and fuel fill door unlocks.
Twice:
The remaining doors and the trunk unlock.
Using the Remote Transmitter Open the door within 30 seconds. If you do not open a door within 30 seconds of unlocking the vehicle with the remote transmitter, the doors will automatically relock.
If the interior light switch is in the door activated position, the interior lights come on when you press the UNLOCK button. No doors opened: The lights fade out after 30 seconds. Doors relocked with the remote: The lights go off immediately.
Î
Interior Lights
P.125
The remote transmitter uses low-power signals, so the operating range may vary depending on the surroundings.
The remote transmitter will not work when the key is in the ignition switch. The remote will not lock the vehicle when a door is open.
If the distance at which it works varies, the battery is probably low. If the LED does not come on when you press a button, the battery is dead.
Î
Replacing the Battery
P.269
31TL1620.indb 91
2010/09/10 16:13:03
Continued
91
Locking and Unlocking the Doors
Locking/Unlocking the Doors from the Outside
Locking/Unlocking the Doors Using a Key
Fully insert the key and turn it. If you are using the master key, make sure it is fully extended.
Locking/Unlocking the Doors Using a Key When you lock the driver's door with a key, all of the other doors, trunk, and fuel fill door lock at the same time. When unlocking, the driver's door and fuel fill door unlock first. Turn the key a second time within a few seconds to unlock the remaining doors and the trunk.
Lock
Unlock
Locking a Door Without Using a Key
Locking the driver's door
Pull the lock tab rearward master door lock switch in the lock direction
or push the
, and close the door. Locking the passenger's doors
Pull the lock tab rearward and close the door.
Lockout prevention system
The doors cannot be locked when the key is in the ignition switch, and any door is open.
Locking a Door Without Using a Key When you lock the driver's door, all the other doors, trunk, and fuel fill door lock at the same time. Make sure you have the key in your hand before locking the door to prevent it from being locked in the vehicle.
92
31TL1620.indb 92
2010/09/10 16:13:03
Locking and Unlocking the Doors
Locking/Unlocking the Doors from the Inside
Locking/Unlocking the Doors from the Inside
Using the Lock Tab
To Lock
To Unlock
Lock Tab
Locking a door
Pull the lock tab rearward.
Unlocking a door
Push the lock tab forward.
Using the Lock Tab When you lock the door using the lock tab on the driver's door, all of the other doors, trunk, and fuel fill door lock at the same time. When you unlock the door using the lock tab on the driver's door, only the driver's door will unlock.
Using the Master Door Lock Switch
To Lock
Press the master door lock switch in as shown to lock or unlock all doors.
Using the Master Door Lock Switch When you lock/unlock the driver's door using the master lock switch, all the other doors, trunk, and fuel fill door lock/unlock at the same time.
To Unlock
Master Door Lock Switch
93
31TL1620.indb 93
2010/09/10 16:13:03
Locking and Unlocking the Doors
Childproof Door Locks
Childproof Door Locks The childproof door locks prevent the rear doors from being opened from the inside regardless of the position of the lock tab. Setting the Childproof Door Locks
Slide the lever in the rear door to the lock position, and close the door.
When opening the door
Unlock
Open the door using the outside door handle.
Lock
Auto Door Lock/Unlock
Auto door lock
The auto door lock function automatically locks all the doors and the trunk, and the fuel fill door when the vehicle reaches about 10 mph (15 km/h).
Auto door unlock
Automatic transmission models When you depress the brake pedal and move the shift lever to P , the driver’s door automatically unlocks. Manual transmission models When you depress the brake pedal and turn the ignition switch to LOCK 0 , the driver’s door automatically unlocks.
94
31TL1620.indb 94
Child Proof Door Locks To open the door from the inside when the childproof door lock is on, put the lock tab in the unlock position, lower the rear window, put your hand out of the window, and pull the outside door handle.
Auto Door Lock/Unlock The auto door lock/unlock settings can be customized using the multi-information display.
Î
Customization Procedure
P. 80
2010/09/10 16:13:04
Opening and Closing the Trunk
Precautions for Opening/Closing the Trunk
Opening the trunk
Open the trunk all the way.
If it is not fully opened, the trunk lid may begin to close under its own weight.
Closing the trunk
Keep the trunk lid closed while driving to:
Avoid possible damage. Prevent exhaust gas from leaking into the vehicle. Carbon Monoxide
P.60
Î
Using the Trunk Opener
Trunk Release
Pressing the trunk release to the lower left of the driver's seat unlocks and opens the trunk.
95
31TL1620.indb 95
2010/09/10 16:13:05
Opening and Closing the Trunk
Using the Remote Transmitter
Using the Remote Transmitter
Press the trunk release button for approximately one second to unlock and open the trunk.
Trunk Button
Using the Trunk Release Switch
Push up the release switch on the trunk lid after the doors are unlocked.
Release Switch
Using the Remote Transmitter When the driver's door is locked: The trunk will lock when it is closed. When the driver's door is unlocked: The trunk will not lock when it is closed.
When the ignition switch is in any position except LOCK 0 , you cannot open the trunk using the trunk release button on the remote transmitter.
96
31TL1620.indb 96
2010/09/10 16:13:05
Trunk Main Switch
Main Switch
ON
OFF
The trunk main switch disables the trunk opener on the driver's side and the trunk release button on the trunk lid to protect luggage in the trunk.
1. Make sure the rear seat-backs are not
folded down.
2. Turn off the trunk main switch in the glove
box.
3. Lock the glove box.
Emergency Trunk Opener
Lever
The trunk release lever allows you to open the trunk from inside for your safety.
Slide the release lever in the direction of the arrow.
Opening and Closing the Trunk
Trunk Main Switch
Trunk Main Switch If you need to give the key to someone else, give them the valet key.
The trunk release button on the remote transmitter is always enabled, even when the trunk main switch is off.
Emergency Trunk Opener Parents should decide if their children should be shown how to use this feature.
97
31TL1620.indb 97
2010/09/10 16:13:05
Security System
Immobilizer System The immobilizer system prevents a key that has not been pre-registered from starting the engine. Each key contains electronic transmitters that use electronic signals to verify the key.
Pay attention to the following when inserting the key into the ignition switch. • Do not allow objects that emit strong radio waves near the ignition switch. • Make sure the key is not covered by or touching a metal object. • Do not bring a key from another vehicle's immobilizer system near the ignition switch.
Security System Alarm
The security system alarm activates when the doors, trunk, or hood are opened without the key, or remote transmitter. It also activates if you turn the ignition switch to ON II after locking the doors with the remote transmitter.
When the security system alarm activates
The horn sounds intermittently, and all of the exterior lights flash.
To deactivate the security system alarm
Unlock the vehicle using the key, or remote transmitter. The system, along with the horn and flashing lights, are deactivated.
Immobilizer System NOTICE Leaving the ignition key in the vehicle can result in theft or accidental movement of the vehicle. Always take the ignition key with you whenever you leave the vehicle unattended.
Do not alter the system or add other devices to it. Doing so may damage the system and make your vehicle inoperable.
Security System Alarm The security alarm continues for a maximum of two minutes until the security system deactivates.
98
31TL1620.indb 98
2010/09/10 16:13:05
Security System
Security System Alarm
Security System Alarm Do not set the security system alarm when someone is in the vehicle or a window is open. The system can accidentally activate when: •
Unlocking the door with the lock tab or the master door lock switch. Opening the trunk with the release button on the driver's door or the emergency trunk opener.
•
If the battery goes dead after you have set the security system alarm, the security alarm may go off once the battery is recharged or replaced. If this occurs, deactivate the security system alarm by unlocking a door using the key or remote transmitter.
Do not attempt to alter this system or add another device to it.
Setting the security system alarm
The security system alarm automatically sets when the following conditions have been met: •
0 , and the key has been removed from the
The ignition switch is in LOCK ignition switch. The hood is closed. All doors are locked. When the security system alarm sets
• •
The security system indicator in the instrument panel blinks. When the blinking interval changes after about 15 seconds, the security system is set.
To cancel the security system alarm
The security system is canceled when the vehicle is unlocked using the key or remote transmitter. The security system indicator goes off at the same time.
Panic Mode
Panic Button
The panic button on the remote transmitter
If you press the panic button for approximately one second, the following will occur:
• •
The horn sounds. Some exterior lights flash for about 30 seconds.
Canceling panic mode
Press any button on the remote transmitter, or turn the ignition switch to ON II .
31TL1620.indb 99
2010/09/10 16:13:06
99
Opening and Closing the Windows
Opening/Closing the Power Windows The power windows can be opened and closed when the ignition switch is in ON II , using the switches on the doors. The driver's side switch can be used to open and close all of the windows.
The main switch on the driver's side must be switched off (not pushed in, indicator off) to open and close the windows from anywhere other than the driver's seat.
When the main switch is turned on (pushed in, indicator on), you can only operate the windows from the driver's seat. Turn the main switch on when children are in the vehicle.
Opening/Closing Windows with Auto-Open/Close Function
Driver’s Window Switch
ON OFF
Main Switch
Indicator
Front Passenger’s Window Switch
Automatic operation
To open: Push the switch down firmly To close: Pull the switch up firmly. The window opens or closes completely. To stop the window at any time, push or pull the switch briefly.
Manual operation
To open: Push the switch down lightly. To close: Pull the switch up lightly. Release the switch when the window reaches the desired position.
Opening/Closing the Power Windows
WARNING
Closing a power window on someone's hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
The power windows can be operated for up to 10 minutes after you turn the ignition switch off. Opening either front door cancels this function.
Auto Reverse If a power window senses resistance when closing automatically, it will stop closing and reverse direction.
The driver’s window auto reverse function is disabled when you continuously pull up the switch.
The auto reverse function stops sensing when the window is almost closed to ensure that it fully closes.
100
31TL1620.indb 100
2010/09/10 16:13:06
Opening and Closing the Windows
Opening/Closing the Power Windows
Opening/Closing Windows without Auto-Open/Close Function
Close
Open
To open: Push the switch down. To close: Pull the switch up. Release the switch when the window reaches the desired position.
Opening Windows and Moonroof with the Remote Transmitter
To open: Press the UNLOCK button twice within 10 seconds and hold it down for the second time. If the windows stop midway, repeat the procedure.
Opening Windows and Moonroof with the Remote Transmitter You cannot operate the power windows with the remote transmitter when the key is in the ignition switch.
Unlock Button
31TL1620.indb 101
2010/09/10 16:13:06
Continued
101
Opening and Closing the Windows
Opening/Closing the Power Windows
Opening/Closing the Windows/Moonroof with the Key
Close
Open
To open: Unlock the driver's door with the key. Within 10 seconds of returning the key to the central position, turn the key in the unlock direction and hold it there.
To close: Lock the driver's door with the key. Within 10 seconds of returning the key to the central position, turn the key in the lock direction and hold it there.
Release the key to stop the windows/ moonroof at the desired position. If you want further adjustment, repeat the same operation.
Opening/Closing the Windows/Moonroof with the Key You cannot close the power windows with the key when the door is open.
102
31TL1620.indb 102
2010/09/10 16:13:06
Opening and Closing the Moonroof
Opening/Closing the Moonroof
You can only operate the moonroof when the ignition switch is in ON II . Use the switch in the front of the ceiling to open and close the moonroof.
Automatic operation
To open: Pull the switch back firmly, then