2011 Acura TL Owners Manual

Download PDF Manual
To have the driver’s ID detected, make sure the driver’s door is unlocked with a corresponding remote transmitter/keyless access remote. 2011 TL10/07/29 11:51:50 31TK4620_098 Onmodelswithoutkeylessaccesssystem If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’ Multi-Information Display DRIVER’S ID U.S. model is shown. Press the SEL/RESET button. TM If you want to change any vehicle control settings, select Keyless Memory Settings by pressing either INFO button ( / ), then press the SEL/RESET button. Select CHG SETTING, then press the SEL/RESET button. ▲ ▼ Refer to the table on the following pages about the settings you want to customize. CONTINUED 93 2011 TL10/07/29 11:51:56 31TK4620_099 Multi-Information Display Group Setup METER SETUP (P.99) Menu Item Description Setting Option Page LANGUAGE SELECTION Changes the language used in the display. ADJUST OUTSIDE TEMP. DISPLAY Changes the outside temperature reading above or below its current reading. TRIP COMPUTER TRIP A INFO RESET Causes trip meter A and the average fuel economy to reset when you refuel. ADJUST ALARM VOLUME Changes the indicator alarm volumes into three levels. AUTO INTERIOR ILLUMINATION Changes the interior light sensitivity to your liking. 〜 5°F 〜 3°C ＊ ＊ ＊ ＊ 0°F 0°C ENGLISH FRENCH SPANISH 5°F − 〜 ± (U.S.) 3°C − 〜 ± (Canada) WITH REFUEL MANUAL ONLY IGN OFF HIGH MID ＊ LOW MAX HIGH MID ＊ ON ＊ OFF ON OFF ＊ LOW MIN OFF 100 101 102 104 105 106 109 POSITION SETUP (P.108) KEYLESS START GUIDANCE SCREENS MEMORY POSITION LINK ＊ Changes the display of the keyless start guidance screens. Changes the driver’s seat and the outside mirror positions to a stored setting. ＊＊ 1 : 2 : Default setting Only on models with keyless access system 94 2011 TL10/07/29 11:52:03 31TK4620_100 Group Setup KEYLESS ACCESS SETUP (P.111) ＊ Menu Item DOOR UNLOCK MODE KEYLESS ACCESS LIGHT FLASH LIGHTING SETUP (P.116) KEYLESS ACCESS BEEP INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY ＊＊ 1 : 2 : Default setting Only on models with keyless access system Multi-Information Display Description Setting Option Changes which doors unlock when you use the remote or grab the driver’s door handle. Causes some exterior lights to blink when you unlock/lock the doors by grabbing or touching the sensor/pushing the button on the driver’s door handle. Causes the beeper to sound when you unlock/lock the doors by grabbing or touching the sensor/ pushing the button on the driver’s door handle. Changes how long (in seconds) the interior lights stay on after you close the doors. Changes how long (in seconds) the exterior lights stay on after you close the driver’s door. Changes the timing of when the headlights come on. The headlight switch needs to be in the AUTO position. ＊ DRIVER DOOR ALL DOORS ON OFF ＊ ＊ ON OFF 15 sec 0 sec LOW MIN ＊ ＊ 60 sec 30 sec 60 sec 30 sec 15 sec MAX HIGH MID ＊ Page 112 113 114 117 118 119 CONTINUED 95 2011 TL10/07/29 11:52:09 31TK4620_101 Multi-Information Display Group Setup DOOR/WINDOW SETUP (P.121) Menu Item AUTO DOOR LOCK Description Setting Option Changes when the doors automatically lock. AUTO DOOR UNLOCK Changes when the doors automatically unlock. Changes which doors unlock with the remote transmitter/keyless access remote on the first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Set/Cancel all the customized settings as default. KEY AND REMOTE UNLOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER DEFAULT ALL (P.129) ＊＊＊ 1 : 2 : 3 : Default setting Default setting for automatic transmission Default setting for manual transmission 96 ＊ ＊ SHIFT FROM P (A/T only) WITH VEHICLE SPEED OFF SHIFT TO P/DRIVER DOOR (A/T only) SHIFT TO P/ALL DOORS (A/T only) IGN OFF/DRIVER DOOR IGN OFF/ALL DOORS OFF DRIVER DOOR ALL DOORS ＊ ＊ ＊ ON OFF 90 sec 60 sec 30 sec CANCEL SET ＊ Page 122 123 125 126 127 129 2011 TL10/07/29 11:52:18 31TK4620_102 Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize: METER SETUP POSITION SETUP KEYLESS ACCESS SETUP LIGHTING SETUP DOOR/WINDOW SETUP ＊ ＊ : Only on models with keyless access system Multi-Information Display Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button until you see the setup you want to customize, then press the SEL/RESET button to enter your selection. ▲ ▼ If you do not make any changes, select ‘‘EXIT.’’ The display returns to the normal display. If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page 129 CONTINUED 97 When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG SETTING, then press the SEL/ RESET button. ▲ ▼ 2011 TL10/07/29 11:52:23 31TK4620_103 Multi-Information Display DEFAULT ALL See page 129. ). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. : On models with keyless access system only ＊ METER SETUP See page 99. POSITION SETUP See page 108. KEYLESS ACCESS SETUP ＊ See page 111. LIGHTING SETUP See page 116. DOOR/WINDOW SETUP See page 121. 98 2011 TL10/07/29 11:52:32 31TK4620_104 Meter Setup Here are the five or six custom settings for the meter setup: LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP COMPUTER TRIP A INFO RESET ADJUST ALARM VOLUME AUTO INTERIOR ILLUMINATION Onmodelswithkeylessaccess system KEYLESS START GUIDANCE SCREENS Multi-Information Display See page 100. See page 101. See page 102. See page104 . See page 105. Onmodelswithkeylessaccesssystemonly See page 106. ). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. CONTINUED 99 2011 TL10/07/29 11:52:40 31TK4620_105 Multi-Information Display While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection. ▲ ▼ LanguageSelection There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions: You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ Press the SEL/RESET button to see the selections. Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ 100 2011 TL10/07/29 11:52:49 31TK4620_106 Multi-Information Display AdjustOutsideTemp.Display U.S. models Canadian models When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again. If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions: You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to enter the setting. ▲ ▼ The displayed number is the current adjustment above or below the outside temperature. Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value. ▲ ▼ CONTINUED 101 2011 TL10/07/29 11:52:59 31TK4620_107 Multi-Information Display U.S. models Canadian models TripComputerTripAInfoReset You can select the reset timing of the Trip A information: Trip A, Average Fuel Economy A, Average Vehicle Speed A, and Elapsed Time A. WITH REFUEL information is reset every time you refuel your vehicle. The Trip A − There are three reset choices you can make: MANUAL ONLY You can reset the Trip A information when Trip A is displayed (see page − 81 ). − The Trip A information IGN OFF is reset when you turn the ignition switch to the LOCK (0) position. ＊ ＊ Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0). For more information, see pages 178 and 181 You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again. 102 2011 TL10/07/29 11:53:06 31TK4620_108 Multi-Information Display Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP COMPUTER TRIP A INFO RESET’’ and repeat the procedure again. CONTINUED 103 2011 TL10/07/29 11:53:13 31TK4620_109 Multi-Information Display AdjustAlarmVolume Select the warning alarm volume from three levels. You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ Press the SEL/RESET button to see the selections. Select the desired level by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST ALARM VOLUME’’ and repeat the procedure again. 104 2011 TL10/07/29 11:53:22 31TK4620_110 AutoInteriorIllumination While the headlight switch is turned on, the interior lights gradually dim, as the outside light level gets low. You can customize at which outside light level the lights start to dim. There are MAX, HIGH, MID, LOW and MIN levels and OFF for the auto interior illumination settings. If you want the illuminations to start dimming as early as possible, select MAX. For illuminations to start dimming as late as possible, select MIN. Choose HIGH, MID, or LOW for levels in between. To disable the auto interior illumination function, select OFF. Multi-Information Display You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ Press the SEL/RESET button to see the selections. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ CONTINUED 105 2011 TL10/07/29 11:53:28 31TK4620_111 Multi-Information Display When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO INTERIOR ILLUMINATION’’ and repeat the procedure again. 106 KeylessStartGuidanceScreens Onmodelswithkeylessaccesssystem When this item is set to ON, you will see some guidance messages on the multi-information display. You can change this setting between on and off. For more information on start guidance messages, see page 182 You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ 2011 TL10/07/29 11:53:34 31TK4620_112 Multi-Information Display Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS START GUIDANCE SCREENS’’ and repeat the procedure again. 107 2011 TL10/07/29 11:53:40 31TK4620_113 Multi-Information Display Position Setup You can customize the MEMORY POSITION LINK setting in position setup. While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. / ) button, the screen changes Each time you press the INFO ▲ ▼ asshown in the illustration. Press the INFO ( / ) button until you see the custom setting then press the SEL/RESET button to enter your selection. ▲ ▼ 108 See page109 . ). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. 2011 TL10/07/29 11:53:48 31TK4620_114 MemoryPositionLink When Memory Position Link is set to ON, the driver’s seat and the outside mirrors move to the positions stored in memory. To cause the memory to activate, open the driver’s door with the remote transmitter. On models with keyless access system, open the driver’s door with the remote, or grab the door handle while carrying the remote. To set the memory positions, see page 164 Onmodelswithkeylessaccesssystem For information on using the remote, see page 167 Multi-Information Display You can choose this item to customize from ‘‘POSITION SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button. ▲ ▼ CONTINUED 109 2011 TL10/07/29 11:53:53 31TK4620_115 Multi-Information Display When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘MEMORY POSITION LINK’’ and repeat the procedure again. 110 2011 TL10/07/29 11:54:01 31TK4620_116 Keyless Access Setup Onmodelswithkeylessaccesssystem There are three custom settings for the keyless access setup: DOOR UNLOCK MODE KEYLESS ACCESS LIGHT FLASH KEYLESS ACCESS BEEP While ‘‘KEYLESS ACCESS SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. / ) button, the screen changes Each time you press the INFO ▲ ▼ asshown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection. ▲ ▼ Multi-Information Display See page112 . See page113 . See page114 . : Press the INFO button ( ). ▲ ▼ : Press the SEL/RESET button. CONTINUED 111 2011 TL10/07/29 11:54:09 31TK4620_117 Multi-Information Display DoorUnlockMode Press the SEL/RESET button to see the selections. Select DRIVER DOOR or ALL DOORS by pressing the INFO ( / ) button, then enter your ▲ ▼ selection by pressing the SEL/RESET button . When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘DOOR UNLOCK MODE’’ and repeat the procedure again. To select whether the driver’s door or all doors unlock when you open the driver’s door with the remote or by grabbing the door handle (while carrying the remote), follow these instructions: You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ▲ ▼ ) button repeatedly. 112 2011 TL10/07/29 11:54:16 31TK4620_118 KeylessAccessLightFlash When KEYLESS ACCESS LIGHT FLASH is set to ON, some exterior lights blink twice when you unlock the doors by grabbing the driver’s door handle while carrying the remote. The same exterior lights blink once when you lock the doors by pushing the door lock button while carrying the remote. Multi-Information Display You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ) button repeatedly. ▲ ▼ Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ CONTINUED 113 2011 TL10/07/29 11:54:23 31TK4620_119 Multi-Information Display When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS ACCESS LIGHT FLASH’’ and repeat the procedure again. 114 KeylessAccessBeep When KEYLESS ACCESS BEEP is set to ON, the beeper sounds twice when you unlock the doors by grabbing the drivers door handle while carrying the remote. When you lock the doors by pushing the door lock button while carrying the remote, the beeper sounds once. You can choose this item to customize from ‘‘KEYLESS ACCESS SETUP’’ by pressing the INFO ( / ▲ ▼ ) button repeatedly. 2011 TL10/07/29 11:54:29 31TK4620_120 Multi-Information Display Press the SEL/RESET button to see the selections. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS ACCESS BEEP’’ and repeat the procedure again. 115 2011 TL10/07/29 11:54:37 31TK4620_121 Multi-Information Display Lighting Setup Here are the three custom settings for the lighting setup: INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO / ) button, the screen chang ▲ ▼ asshown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection. ▲ ▼ es 116 See page 117. See page 118. See page 119. ). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. 2011 TL10/07/29 11:54:45 31TK4620_122 InteriorLightDimmingTime Multi-Information Display The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions: You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼ ) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired setting (15 sec, 30 sec, or 60 sec) by pressing the INFO ( / ) button, then enter your ▲ ▼ selection by pressing the SEL/ RESET button. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again. CONTINUED 117 2011 TL10/07/29 11:54:51 31TK4620_123 Multi-Information Display HeadlightAutoOffTimer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the driver’s door. On models with keyless access system, the lights go off after the selected time when you close the driver’s door and take the remote with you. To change how long the lights stay on before they go off, follow these instructions: 118 You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly. Press the SEL/RESET button to see the selections. Select the desired setting (60 sec, 30 sec, 15 sec or 0 sec) by pressing the enter your selection by pressing the SEL/RESET button. INFO ( / ) button, then enter ▲ ▼ 2011 TL10/07/29 11:55:01 31TK4620_124 Multi-Information Display − − AutoLightSensitivity The headlights automatically come on when the headlight switch is in the AUTO position and the ambient light reaches a changeable level. You can select the auto light sensitivity from the following five levels: MAX The headlights come on when it is bright. HIGH The headlights come on when it is somewhat bright. MID The headlights come on when it is as bright as sunset or sunrise. LOW The headlights come on when it is somewhat dark. MIN The headlights come on when it is dark. − − − You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly CONTINUED 119 When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘HEADLIGHT AUTO OFF TIMER’’ and repeat the procedure again. 2011 TL10/07/29 11:55:06 31TK4620_125 Multi-Information Display Press the SEL/RESET button to see the selections. Select the desired setting (MAX, HIGH, MID, LOW or MIN) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO LIGHT SENSITIVITY’’ and repeat the procedure again. 120 2011 TL10/07/29 11:55:17 31TK4620_126 Door/Window Setup Here are the five custom settings for the door setup: AUTO DOOR LOCK AUTO DOOR UNLOCK KEY AND REMOTE UNLOCK MODE KEYLESS LOCK ACKNOWLEDGMENT SECURITY RELOCK TIMER While ‘‘DOOR/WINDOW SETUP’’ is shown, press the SEL/RESET button to enter the customize mode. Each time you press the INFO / ) button, the screen chang ▲ ▼ asshown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection. ▲ ▼ es Multi-Information Display See page122 . See page123 . See page125 . See page 126. See page 127. ). : Press the INFO button ( ▲ ▼ : Press the SEL/RESET button. CONTINUED 121 2011 TL10/07/29 11:55:25 31TK4620_127 Multi-Information Display AutoDoorLock There are three settings you can choose from: − SHIFT FROM P The doors lock whenever you move the shift lever out of Park. (Automatictransmissionmodelonly) WITH VEHICLE SPEED The doors lock when the vehicle speed reaches about 10 mph (about 16 km/h). − − OFF The auto door lock is deactivated all the time. 122 You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly. A/T model is shown. Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ 2011 TL10/07/29 11:55:34 31TK4620_128 Multi-Information Display AutoDoorUnlock There are five possible settings for automatic transmission models and three possible settings for manual transmission models. Automatictransmissionmodelonly DRIVER DOOR WITH SHIFT TOP The driver’s door unlocks when − you move the shift lever to Park with the brake pedal depressed. Automatictransmissionmodelonly − ALL DOORS WITH SHIFT TO P All the doors unlock when you move the shift lever to Park with the brake pedal depressed. − DRIVER DOOR WITH IGN OFF The driver’s door unlocks when you turn the ignition switch to the LOCK (0) position. ＊ A/T model is shown. When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR LOCK’’ and repeat the procedure again. ALL DOORS WITH IGN OFF All the doors unlock when you turn the ignition switch to the LOCK (0) position. − ＊ − OFF deactivated all the time. The auto door unlock is ＊ Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. VEHICLE OFF (LOCK) Mode is the equivalent of LOCK (0). For more information, see pages 178 and 181 CONTINUED 123 2011 TL10/07/29 11:55:40 31TK4620_129 Multi-Information Display You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly A/T model is shown. Press the SEL/RESET button to see the selections. If you choose ‘‘IGN OFF,’’ you will see the above display. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ ▲ ▼ Press the INFO ( / ) button to switch the door lock mode setting between the driver’s door and all doors. Then, press the SEL/RESET button to enter your selection. 124 2011 TL10/07/29 11:55:49 31TK4620_130 Multi-Information Display KeyandRemoteUnlockMode When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘AUTO DOOR UNLOCK’’ and repeat the procedure again. You can select whether the driver’s door or all the doors unlock the first time you press the unlock button on the remote transmitter/keyless access remote. You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly. Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ CONTINUED 125 2011 TL10/07/29 11:55:56 31TK4620_131 Multi-Information Display KeylessLockAcknowledgment When you press the LOCK button on the remote transmitter or the keyless access remote, some exterior lights flash, and a beeper sounds when you push the LOCK button again within 5 seconds to verify that the doors and the trunk are locked and the security system has set (see page customize the exterior lights not to flash and the beeper not to sound. ). You can 377 You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEY AND REMOTE UNLOCK MODE’’ and repeat the procedure again. When you press the UNLOCK button on the remote transmitter or the keyless access remote to unlock the driver’s door/all the doors (depending on the customize setting), the exterior lights blink twice to verify that the door(s) is unlocked and the security system is turned off. To turn this feature on or off, follow these instructions. 126 2011 TL10/07/29 11:56:04 31TK4620_132 Press the SEL/RESET button to enter the selecting mode. Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ and repeat the procedure again. Multi-Information Display SecurityRelockTimer If you unlock the doors with the remote transmitter or the keyless access remote, but do not open any of the doors within 30 seconds, the doors automatically relock, and the security system sets. You can change this relock time from 30 seconds to 60 or 90 seconds. Onmodelswithkeylessaccesssystem When you unlock the doors by touching either front door handle while carrying the keyless access remote, the relock time is fixed in 30 seconds. CONTINUED 127 2011 TL10/07/29 11:56:11 31TK4620_133 Multi-Information Display You can choose this item to customize from ‘‘DOOR/WINDOW SETUP’’ by pressing the INFO ▲ ▼( / ) button repeatedly. Press the SEL/RESET button to enter the selecting mode. Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button. ▲ ▼ When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen. If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘SECURITY RELOCK TIMER’’ and repeat the procedure again. 128 2011 TL10/07/29 11:56:19 31TK4620_134 DEFAULT ALL Multi-Information Display If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button. ▲ ▼ To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button. ▲ ▼ If you want to cancel DEFAULT ALL, select CANCEL, then press the SEL/RESET button. The screen goes back to the previous display. When DEFAULT ALL is set, you will see the above display for several seconds, then the screen returns to the default all setting display. If the setting is not successfully completed, ‘‘FAILED’’ is shown for several seconds, and then the screen goes back to the normal message mode. Repeat the same procedure to select DEFAULT ALL. 129 2011 TL10/07/29 11:56:28 31TK4620_135 Controls Near the Steering Wheel REMOTE AUDIO CONTROL BUTTONS (P. 370) PADDLE SHIFTERS (P. 473) WINDSHIELD WIPERS/WASHERS (P. 131) ENGINE START/STOP BUTTON (P. 178) HEADLIGHTS/TURN SIGNALS/ FOG LIGHTS (P. 133, 137) INSTRUMENT PANEL BRIGHTNESS (P. 137) VEHICLE STABILITY ASSIST (VSA) SYSTEM OFF SWITCH (P. 485) HEADLIGHT WASHERS ＊ (P. 132) VOICE CONTROL BUTTONS for NAVIGATION SYSTEM / BLUETOOTH HANDSFREELINK SYSTEM (P. 389, 406) ＊ STEERING WHEEL ADJUSTMENTS (P. 140) NAVIGATION DISPLAY ＊ PASSENGER AIR BAG OFF INDICATOR (P. 34) HAZARD WARNING BUTTON (P. 139) CENTER DISPLAY (P. 217, 274) REAR WINDOW DEFOGGER/HEATED MIRROR BUTTON (P. 139, 163) INTERFACE DIAL ＊ SELECTOR KNOB (P. 226) ＊ (P. 273) HORN ＊ MULTI-INFORMATION DISPLAY BUTTONS (P. 78) SEAT HEATER SWITCHES (P. 196) KEYLESS ACCESS REMOTE SLOT (P. 191) A/T model with navigation system is shown. CRUISE CONTROL BUTTONS (P. 383) To use the horn, press the center pad of the steering wheel. If equipped Refer to the navigation system owner’s manual. 1 : ＊ 2 : ＊ 3 : ＊ 130 2011 TL10/07/29 11:56:36 31TK4620_136 ADJUSTMENT RING 1. 2. 3. 4. 5. 6. Intermittent MIST OFF INT LO Low speed HI High speed Windshield washers − − − Windshield Wipers and Washers Push the right lever up or down to select a position. MIST The wipers run at high speed until you release the lever. − OFF − The wipers are not activated. − INT The length of the wipe interval is varied automatically according to vehicle’s speed. Vary the delay by turning the adjustment ring. If you turn it to the shortest delay ( position), the wipers change to low speed operation when the vehicle speed exceeds 12 mph (20 km/h). LO − The wipers run at low speed. HI −

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2011 Acura TL Owners Manual