2013 Acura RDX Owners Manual

1Locking a Door Without Using a Key

When you lock the driver's door, all the other doors and tailgate lock at the same time. Make sure you have the key with you when locking a door from the outside.

2013 RDXuuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Outside

■ Using the Keyless Access System

When you carry the keyless access remote, you can lock/unlock the doors and the tailgate.

You can lock/unlock the doors within a radius of about 32 inches (80 cm) of the outside door handle. You can open the tailgate within about 32 inches (80 cm) radius from the tailgate release button.

■ Locking the doors and tailgate Press the door lock button on the front door or the tailgate.

uSome exterior lights flash; the beeper sounds; all the doors and tailgate lock; and the security system sets.

Door Lock Button

1Using the Keyless Access System

• The driver must carry the keyless access remote and

not leave it in the vehicle when you get out.

• A person who is not carrying the keyless access

remote can lock/unlock the doors if a person who is carrying it is within range.

• The door may be unlocked if the door handle is

covered with water in heavy rain or in a car wash if the keyless access remote is within range.

• If you grip a front door handle wearing gloves, the

door sensor may be slow to respond or may not respond by unlocking the doors.

• The door might not open if you pull it immediately

after gripping the door handle. Grip the handle again and confirm that the door is unlocked before pulling the handle.

• The driver must carry the keyless access remote and

not leave it in the vehicle when you get out.

• A person who is not carrying the keyless access

remote can unlock the tailgate if a person who is carrying it is within range.

Lock Button

Continued

QRG

TOC

Index

101

2013 RDXuuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Outside

■ Unlocking the doors and tailgate Grab the driver’s door handle: uThe driver’s door unlocks. uSome exterior lights flash twice and the

beeper sounds twice.

Grab the front passenger’s door handle:

uAll the doors unlock. uSome exterior lights flash twice and the

beeper sounds twice.

Press the tailgate release button:

uThe tailgate unlocks and opens. uSome exterior lights flash twice and the

beeper sounds twice.

2 Opening/Closing the Tailgate Using the

Tailgate Release Button P. 108

1Using the Keyless Access System

• Even within the 32 inches (80 cm) radius, you may

not be able to lock/unlock the doors with the keyless access remote if it is above or below the outside handle.

• The keyless access remote may not operate if it is

too close to the door and door glass.

If you do not open a door within 30 seconds of unlocking the vehicle, the doors will automatically relock.

The light flash, beep and unlock settings can be customized using the multi-information display.

2 Customized Features P. 87

Tailgate Release Button

QRG

TOC

Index

102

2013 RDXuuLocking and Unlocking the DoorsuLow Keyless Access Remote Signal Strength

Low Keyless Access Remote Signal Strength The vehicle transmits radio waves to locate the keyless access remote when locking/ unlocking the doors, opening the tailgate, or to start the engine.

In the following cases, locking/unlocking the doors or opening the tailgate or starting the engine may be inhibited or operation may be unstable: • Strong radio waves are being transmitted by nearby equipment.

• You are carrying the keyless access remote together with telecommunications

equipment, laptop computers, cell phones, or wireless devices.

• A metallic object is touching or covering the keyless access remote.

1Low Keyless Access Remote Signal Strength

Communication between the keyless access remote and the vehicle consumes the keyless access remote’s battery.

The keyless access remote battery lasts about two years. This changes by how often you use the remote. The battery is consumed whenever the keyless access remote is receiving strong radio waves. Avoid placing it near electrical appliances such as televisions and personal computers.

QRG

TOC

Index

103

2013 RDXuuLocking and Unlocking the DoorsuLocking/Unlocking the Doors from the Inside

QRG

Locking/Unlocking the Doors from the Inside ■ Using the Lock Tab

To Lock

Lock Tab

To Unlock

■ Locking a door Push the lock tab forward.

■ Unlocking a door Pull the lock tab rearward.

1Using the Lock Tab

When you lock the door using the lock tab on the driver's door, all the other doors and tailgate lock at the same time. When you unlock the door using the lock tab on the driver's door, only the driver's door will unlock.

■ Unlocking Using the Inner Handle of Front Doors Pull the front door inner handle.

uThe door unlocks and opens in one

motion.

Inner Handle

1Unlocking Using the Inner Handle of Front Doors

The front door inner handles are designed to allow front seat occupants to open the door in one motion. However this feature requires that front seat occupants never pull a front door inner handle while the vehicle is in motion.

Children should always ride in a rear seat where childproof door locks are provided.

2 Childproof Door Locks P. 105

TOC

Index

104

2013 RDXuuLocking and Unlocking the DoorsuChildproof Door Locks

■ Using the Master Door Lock Switch

Press the master door lock switch in as shown to lock or unlock all doors and the tailgate.

To Lock

1Using the Master Door Lock Switch

When you lock/unlock the driver's door using the master door lock switch, all the other doors and the tailgate lock/unlock at the same time.

To Unlock

Master Door Lock Switch

Childproof Door Locks The childproof door locks prevent the rear doors from being opened from the inside regardless of the position of the lock tab.

■ Setting the Childproof Door Locks

Slide the lever in the rear door to the lock position, and close the door.

■ When opening the door Open the door using the outside door handle.

Unlock

Lock

1Childproof Door Locks

To open the door from the inside when the childproof door lock is on, put the lock tab in the unlock position, lower the rear window, put your hand out of the window, and pull the outside door handle.

QRG

TOC

Index

105

2013 RDXuuLocking and Unlocking the DoorsuAuto Door Locking/Unlocking

QRG

Auto Door Locking/Unlocking Your vehicle locks all doors and unlocks the driver’s door automatically when a certain condition is met.

■ Auto Door Locking ■ Drive lock mode All doors and tailgate lock when the vehicle’s speed reaches about 10 mph (15 km/h).

TOC

■ Auto Door Unlocking ■ Park unlock mode The driver’s door unlocks when the shift lever is moved into (P with the brake pedal depressed.

1Auto Door Locking/Unlocking

You can turn off or change to another auto door locking/unlocking setting using the multi-information display.

2 Customized Features P. 87

Index

106

2013 RDXOpening and Closing the Tailgate

Precautions for Opening/Closing the Tailgate Always make sure individuals and objects are clear of the tailgate before opening or closing it.

■ Opening the tailgate • Open the tailgate all the way.

u If it is not fully opened, the tailgate may come down accidentally by its own

weight.

• Be careful when it is windy. The wind may cause the tailgate to close.

■ Closing the tailgate Keep the tailgate closed while driving to:

uAvoid possible damage. uPrevent exhaust gas from leaking into the vehicle. 2 Carbon Monoxide Gas P. 64

QRG

TOC

1Precautions for Opening/Closing the Tailgate

Models with power tailgate

3WARNING

Closing a power tailgate while anyone is in the path of the tailgate can cause serious injury.

Make sure everyone is clear before closing the tailgate.

Be careful not to hit your head on the tailgate or to put your hands between the tailgate and the cargo area when closing the gate.

When operating the power tailgate, make sure there is enough space around your vehicle. People near the tailgate may be seriously hurt if the tailgate hits or closes on their heads. Be especially cautious if children are around.

When you are storing or picking up luggage from the cargo area while the engine is idling, do not stand in front of the exhaust pipe. You may get burned.

Do not allow any passenger in the cargo space. They may get hurt during hard braking, a sudden acceleration, or a crash.

Index

107

2013 RDXuuOpening and Closing the TailgateuOpening/Closing the Tailgate Using the Tailgate Release Button

QRG

Opening/Closing the Tailgate Using the Tailgate Release Button

When all the doors are unlocked, the tailgate is unlocked. Press the tailgate release button and lift open the tailgate.

1Opening/Closing the Tailgate Using the Tailgate Release Button

Do not leave the keyless access remote inside the cargo area and close the tailgate. The beeper sounds and the tailgate cannot be closed.

TOC

Tailgate Release Button

To manually close the tailgate, grab the inner handle, pull the tailgate down, and push it closed from outside.

Inner Handle

Index

108

2013 RDXuuOpening and Closing the TailgateuOpening/Closing the Power Tailgate*

Opening/Closing the Power Tailgate* The power tailgate can be operated by pressing the power tailgate button on the remote transmitter, pressing the power tailgate switch on the dashboard, or pressing the button on the tailgate.

■ The power tailgate can be opened when: • The tailgate is fully closed.

• The shift lever is in (P.

• Press and hold the tailgate button on the remote transmitter for about one

second. uIf you have changed the POWER TAILGATE KEYLESS OPEN MODE setting to

WHEN UNLOCKED, you need to unlock the tailgate before you press the tailgate button to open it.

2 Customized Features P. 87

■ The power tailgate can be closed when: • The tailgate is fully open.

• The shift lever is in (P.

• Press and hold the tailgate button on the remote transmitter for about one

second.

1Opening/Closing the Power Tailgate *

The power tailgate may not open or close under the following conditions: • The vehicle is parked on a steep hill. • The vehicle is swayed in a strong wind. • The tailgate or the roof is covered with snow or ice.

If you close the power tailgate when all the doors are locked, the power tailgate locks automatically.

If you replace the battery or the power tailgate fuse while the tailgate is open, the power tailgate may be disabled. The power tailgate resumes once you manually close the tailgate.

Installing aftermarket components other than Acura genuine accessories on the power tailgate may prevent it from fully opening or closing.

Make sure the power tailgate is fully open before you get your luggage in and out.

Make sure the power tailgate is fully closed before you start the vehicle.

* Not available on all models

Continued

QRG

TOC

Index

109

2013 RDXQRG

TOC

Index

uuOpening and Closing the TailgateuOpening/Closing the Power Tailgate *

■ Remote Transmitter

Press the power tailgate button for more than one second to operate.

Power Tailgate Button

To reverse direction while the power tailgate is in operation, press the button again. The beeper sounds three times and the tailgate reverses direction.

■ Customizing when to open the tailgate ANYTIME: The power tailgate unlocks and opens at the same time. This is the default setting. WHEN UNLOCKED: The tailgate opens when all doors are unlocked.

2 Customized Features P. 87

■ Power Tailgate Button

1Opening/Closing the Power Tailgate *

If the power tailgate meets resistance while opening or closing, the auto reverse feature reverses the direction. The beeper sounds three times.

The auto reverse function stops sensing when the tailgate is almost closed to make sure that it fully closes.

Do not touch the sensors located on both sides of the tailgate. The power tailgate does not close if you touch either sensor when you are trying to close the tailgate.

Be careful not to scratch the sensors with a sharp object. If scratched, they can be damaged, and the power tailgate closing feature malfunctions.

To open or close the power tailgate, press the tailgate button on the dashboard for about one second. The beeper sounds and some exterior lights flash.

To reverse direction while the power tailgate is in operation, press the button again. The beeper sounds three times and the tailgate reverses direction.

Power Tailgate Button

110

* Not available on all models

2013 RDXuuOpening and Closing the TailgateuOpening/Closing the Power Tailgate*

■ Power Tailgate Close Button

Press the button on the tailgate to close the power tailgate. If you press the button again while the power tailgate is closing, it stops and reverses direction.

1Power Tailgate Close Button

If you push the power tailgate close button while the tailgate is automatically opening or closing, the power tailgate operation stops. Use caution if the tailgate stops in the middle of either operation. It may suddenly swing up or down.

Power Tailgate Close Button

■ Auto-Closer If you manually close the power tailgate, it latches automatically.

1Auto-Closer

The auto-closer feature does not activate if you push the tailgate release button while the power tailgate is closing.

Do not put any force on the tailgate while the power tailgate is latching.

Keep your hands away from the tailgate when you manually close the tailgate and let it latch automatically. It is dangerous to put your hands around the tailgate as it starts to latch itself.

* Not available on all models

Continued

QRG

TOC

Index

111

2013 RDXuuOpening and Closing the TailgateuOpening/Closing the Power Tailgate *

■ Power Tailgate Fail-safe Mode The power tailgate fail-safe mode detects if there is an extra load on the tailgate (for example, it is covered with snow). If an extra load is detected, the tailgate opens completely then lowers to the close position.

1Power Tailgate Fail-safe Mode

If you try to manually close the power tailgate immediately after it fully opens, the power tailgate fail-safe mode may activate.

Once the power tailgate fail-safe mode activates, wait until the power tailgate fully closes. Keep away from the power tailgate when it is in motion.

If the power tailgate fail-safe mode constantly activates, consult at a dealer.

QRG

TOC

Index

112

* Not available on all models

2013 RDXSecurity System

Immobilizer System The immobilizer system prevents a key that has not been pre-registered from starting the engine. Each key contains electronic transmitters that use electronic signals to verify the key.

Pay attention to the following when selecting the ACCESSORY mode with the ENGINE START/STOP button: • Do not allow objects that emit strong radio waves near the ENGINE START/

STOP button.

• Make sure the key is not covered by or touching a metal object.

• Do not bring a key from another vehicle's immobilizer system with the keyless

access remote.

Security System Alarm The security system alarm activates when the doors, tailgate, or hood are opened without the key, remote transmitter or keyless access system.

■ When the security system alarm activates The horn sounds intermittently, and all of the exterior lights flash.

■ To deactivate the security system alarm Unlock the vehicle using the key, remote transmitter, or keyless access system. The system, along with the horn and flashing lights, is deactivated.

Continued

1Immobilizer System

NOTICE Leaving the ignition key in the vehicle can result in theft or accidental movement of the vehicle. Always take the ignition key with you whenever you leave the vehicle unattended.

Do not alter the system or add other devices to it. Doing so may damage the system and make your vehicle inoperable.

1Security System Alarm

The security alarm continues for a maximum of two minutes until the security system alarm deactivates.

QRG

TOC

Index

113

2013 RDXuuSecurity SystemuSecurity System Alarm

■ Setting the security system alarm The security system alarm automatically sets when the following conditions have been met: • The power mode is in VEHICLE OFF (LOCK). • The hood is closed. • All doors and the tailgate are locked from outside with the key, remote

transmitter, or keyless access system.

■ When the security system alarm sets The security system alarm indicator in the instrument panel blinks. When the blinking interval changes after about 15 seconds, the security system alarm is set.

■ To cancel the security system alarm The security system alarm is canceled when the vehicle is unlocked using the key, remote transmitter, or keyless access system. The security system alarm indicator goes off at the same time.

1Security System Alarm

Do not set the security system alarm when someone is in the vehicle or a window is open. The system can accidentally activate when unlocking the door with the lock tab.

If the battery goes dead after you have set the security system alarm, the security alarm may go off once the battery is recharged or replaced. If this occurs, deactivate the security system alarm by unlocking a door using the key, remote transmitter, or keyless access system.

Do not attempt to alter this system or add another device to it.

■ Panic Mode

Panic Button

■ The panic button on the remote

transmitter

If you press the panic button for approximately one second, the following will occur for about 30 seconds: • The horn sounds. • Some exterior lights flash.

■ Canceling panic mode Press any button on the remote transmitter, or set the power mode to ON.

QRG

TOC

Index

114

2013 RDXOpening and Closing the Windows

Opening/Closing the Power Windows The power windows can be opened and closed when the power mode is in ON, using the switches on the doors. The driver side switches can be used to open and close all of the windows.

The power window lock button on the driver side must be switched off (not pushed in, indicator off) to open and close the windows from anywhere other than the driver's seat.

When the power window lock button is pushed in, the indicator comes on and you can only operate the driver's window. Turn the power window lock button on when children are in the vehicle.

1Opening/Closing the Power Windows

3WARNING

Closing a power window on someone's hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

The power windows can be operated for up to 10 minutes after you set the power mode to VEHICLE OFF.

■ Opening/Closing Windows with Auto-Open/Close Function

Opening either front door cancels this function.

ON OFF

Power Window Lock Button

Indicator

Front Passenger’s Window Switch

Driver’s Window Switch

■ Automatic operation To open: Push the switch down firmly.

To close: Pull the switch up firmly. The window opens or closes completely. To stop the window at any time, push or pull the switch briefly.

■ Manual operation To open: Push the switch down lightly.

To close: Pull the switch up lightly. Release the switch when the window reaches the desired position.

Continued

Auto Reverse If a power window senses resistance when closing automatically, it will stop closing and reverse direction.

The driver’s window auto reverse function is disabled when you continuously pull up the switch.

The auto reverse function stops sensing when the window is almost closed to ensure that it fully closes.

QRG

TOC

Index

115

2013 RDXuuOpening and Closing the WindowsuOpening/Closing the Power Windows

■ Opening/Closing Windows without Auto-Open/Close Function

To open: Push the switch down.

To close: Pull the switch up.

Close

Open

Release the switch when the window reaches the desired position.

QRG

TOC

Index

116

2013 RDXuuOpening and Closing the WindowsuOpening/Closing the Power Windows

■ Opening the Windows and Moonroof with the Remote

Unlock Button

To open: Press the UNLOCK button twice within 10 seconds and hold it down for the second time. If the windows stop midway, repeat the procedure.

■ Opening/Closing the Windows and Moonroof with the Key To open: Unlock the driver’s door with the key. Within 10 seconds of returning the key to the central position, turn the key in the unlock direction and hold it there.

Open

Close

To close: Lock the driver’s door with the key. Within 10 seconds of returning the key to the central position, turn the key in the lock direction and hold it there.

Release the key to stop the windows/ moonroof at the desired position. If you want further adjustment, repeat the same operation.

QRG

TOC

Index

117

2013 RDXOpening and Closing the Moonroof

■ Opening/Closing the Moonroof You can only operate the moonroof when the power mode is in ON. Use the switch in the front of the ceiling to open and close the moonroof.

Open

Close

Tilt

■ Automatic operation To open: Pull the switch back firmly, then release. To close: Push the switch forward firmly, then release.

The moonroof will automatically open or close all the way. To stop the moonroof midway, touch the switch briefly.

■ Manual operation To open: Pull the switch back, and hold it until the desired position is reached.

To close: Push the switch forward, and hold it until the desired position is reached.

■ Tilting the moonroof up To tilt: Push on the center of the moonroof switch.

To close: Push the switch forward firmly, then release.

1Opening/Closing the Moonroof

3WARNING

Opening or closing the moonroof on someone's hands or fingers can cause serious injury.

Make sure all hands and fingers are clear of the moonroof before opening or closing it.

NOTICE Opening the moonroof in below freezing temperature or when it is covered with snow or ice can damage the moonroof panel or motor.

The power moonroof can be operated for up to 10 minutes after you set the power mode to VEHICLE OFF. Opening either front door cancels this function.

When resistance is detected, the auto reverse function causes the moonroof to change directions, then stop. Auto reverse stops sensing when the moonroof is almost closed to ensure that it fully closes. Make sure that all objects, including fingers, are clear of the moonroof.

QRG

TOC

Index

118

2013 RDXOperating the Switches Around the Steering Wheel

ENGINE START/STOP Button ■ Changing the Power Mode

Indicator

1ENGINE START/STOP Button

ENGINE START/STOP Button Operating Range

Operating Range

VEHICLE OFF (LOCK) Indicator in the button is off. The steering wheel is locked. The power to all electrical components is turned off.

ACCESSORY Indicator in the button is on. Indicator in the button blinks (from ON to ACCESSORY). Operate the audio system and other accessories in this position.

ON Indicator in the button is on. All electrical components can be used.

: Press the ENGINE START/STOP button to change the mode. : Press the button without the shift lever in (P. : Shift to Park, then press the button.

You can start the engine when the keyless access remote is inside the vehicle. The engine may also run if the keyless access remote is close to the door or window, even if it is outside the vehicle.

ON mode: Indicator in the button is off, if the engine is running.

If the keyless access remote battery is weak, beeper sounds and the TO START, HOLD REMOTE NEAR START BUTTON message appears on the multi- information display.

2 If the Keyless Access Remote Battery is

Weak P. 326

If the power mode does not change from VEHICLE OFF to ACCESSORY, press the ENGINE START/STOP button while moving the steering wheel left and right. The steering wheel will unlock, allowing the mode to change.

Continued

QRG

TOC

Index

119

2013 RDXuuOperating the Switches Around the Steering WheeluENGINE START/STOP Button

■ Power Mode Reminder If you open the driver's door when the power mode is set to ACCESSORY, a warning buzzer sounds.

QRG

TOC

Index

120

2013 RDXuuOperating the Switches Around the Steering WheeluENGINE START/STOP Button

■ Keyless Access Remote Reminder

Warning buzzers may sound from inside or/ and outside the vehicle to remind you that the keyless access remote is out of the vehicle. If the buzzer continues even after the remote is put back inside, place it within its operational range.

■ When the power mode is in ON If the keyless access remote is taken out of the vehicle, and the driver's door is closed, warning buzzers sound from both inside and outside the vehicle. A warning message on the multi-information display notifies the driver inside that the remote is out.

■ When the power mode is in

ACCESSORY or in VEHICLE OFF (LOCK)

If the keyless access remote is taken out of the vehicle, and the driver's door is closed, a warning buzzer sounds from outside the vehicle.

1Keyless Access Remote Reminder

When the keyless access remote is within the system's operational range, and the driver's door is closed, the warning function cancels.

If the keyless access remote is taken out of the vehicle after the engine has been started, you can no longer change the ENGINE START/ STOP button mode or restart the engine. Always make sure if the remote is in your vehicle when you operate the ENGINE START/ STOP button.

Removing the keyless access remote from the vehicle through a window does not activate the warning buzzer.

Do not put a keyless access remote on the dashboard or in the glove box. It may cause the warning buzzer to go off. Under some other conditions that can prevent the vehicle from locating the remote, the warning buzzer may also go off even if the remote is within the system's operational range.

QRG

TOC

Index

121

2013 RDXuuOperating the Switches Around the Steering WheeluTurn Signals

QRG

Turn Signals

Right Turn

Left Turn

Light Switches ■ Manual Operation

High Beams

Flashing the high beams

Low Beams

Turns on parking, side marker, tail, and rear license plate lights Turns on headlights, parking, side marker, tail, and rear license plate lights

TOC

Index

122

The turn signals can be used when the power mode is in ON.

■ One-touch turn signal When you lightly push up or down and release the turn signal lever, the exterior turn signals and turn signal indicator blink three times.

This feature can be used when signaling for a lane change.

Rotating the light switch turns the lights on and off, regardless of the power mode setting. ■ High beams Push the lever forward until you hear a click. ■ Low beams When in high beams, pull the lever back to return to low beams. ■ Flashing the high beams Pull the lever back, and release it.

1Light Switches

If you leave the power mode in VEHICLE OFF (LOCK) while the lights are on, a chime sounds when the driver's door is opened.

Models with high voltage discharge tube bulb Repeatedly turning the headlights on and off reduces the life of the HID headlight bulbs. If you sense that the level of the headlights is abnormal, have the vehicle inspected by a dealer.

Do not leave the lights on when the engine is off because it will cause the battery to discharge.

2013 RDXuuOperating the Switches Around the Steering WheeluLight Switches

■ Automatic Lighting Control

Automatic lighting control can be used when the power mode is in ON.

When you turn the light switch to #Y, the headlights and other exterior lights will switch on and off automatically depending on the ambient brightness.

uYou can change the auto light sensitivity

setting.

2 Customized Features P. 87

1Automatic Lighting Control

We recommend that you turn on the lights manually when driving at night, in a dense fog, or in dark areas such as long tunnels or parking facilities.

The light sensor is in the location shown below. Do not cover this light sensor with anything; otherwise, the automatic lighting system may not work properly.

Light Sensor

Adjust the auto light sensitivity as follows:

Setting

The exterior lights come on when the ambient light is at

MAX HIGH MID LOW MIN

Bright

Dark

Continued

QRG

TOC

Index

123

2013 RDXuuOperating the Switches Around the Steering WheeluLight Switches

■ Headlight Integration with Wiper The headlights automatically come on when the wipers are used several times within certain number of intervals while the headlight switch is in #Y.The headlights automatically go off a few minutes after the wipers are stopped.

■ Automatic Lighting Off Feature

The headlights, all other exterior lights, and the instrument panel lights turn off within 15 seconds after the door is opened and closed with the power mode in VEHICLE OFF (LOCK).

If you set the power mode to VEHICLE OFF (LOCK) with the headlight switch on, but do not open the door, the lights turn off after 10 minutes (three minutes, if the switch is in the #Y position).

The lights turn on again when you unlock or open the driver's door. If you unlock the door, but do not open it within 15 seconds, the lights go off. If you open the driver's door, you will hear a lights on reminder chime.

1Headlight Integration with Wiper *

This feature activates while the headlights are in #Y. The instrument panel brightness does not change when the headlights come on.

If the ambient light is dark, the automatic lighting control overrides this feature, and the headlights come on whether or not the wipers cycle several times.

1Automatic Lighting Off Feature

You can change the headlight auto off timer setting.

2 Customized Features P. 87

QRG

TOC

Index

124

* Not available on all models

2013 RDXuuOperating the Switches Around the Steering WheeluFog Lights*

Fog Lights*

When the low beam headlights are on, turn the fog light switch on to use the fog lights.

1Fog Lights*

The fog lights go off when the headlights turn off, or when the daytime running lights are on.

Fog Light Switch

Daytime Running Lights The high beam headlights come on slightly dimmer than normal when the following conditions have been met:

• The power mode is in ON.

• The headlight switch is off, or in

• The parking brake is released.

The lights remain on even if you set the parking brake. Setting the power mode to VEHICLE OFF (LOCK) will turn off the daytime running lights.

The high beam headlights return to the original brightness once the headlight switch is turned on.

* Not available on all models

QRG

TOC

Index

125

2013 RDXuuOperating the Switches Around the Steering WheeluWipers and Washers

QRG

Wipers and Washers ■ Front Wiper/Washer

TOC

Pull to use washer.

Intermittent Time Adjustment Ring

a MIST b OFF c INT: Low speed with intermittent d LO: Low speed wipe e HI: High speed wipe

Index

126

The windshield wipers and washers can be used when the power mode is in ON.

■ MIST The wipers run at high speed until you release the lever.

■ Wiper switch (OFF, INT, LO, HI) Change the wiper switch setting according to the amount of rain.

■ Adjusting the delay Turn the adjustment ring to adjust the wiper delay.

Long delay

Short delay

1Wipers and Washers

NOTICE Do not use the wipers when the windshield is dry. The windshield will get scratched, or the rubber blades will get damaged.

NOTICE In cold weather, the blades may freeze to the windshield, becoming stuck. Operating the wipers in this condition may damage the wipers. Use the defroster to warm the windshield, then turn the wipers on.

If the vehicle speeds up while the wipers are operating intermittently, the length of the wipe interval shortens. When the vehicle starts moving, the wipers make a single sweep. When the vehicle speeds up, the wiper operation’s shortest delay setting ( the same.

) and the LO setting become

Turn the washers off if no washer fluid comes out. The pump may get damaged.

■ Washer Sprays while you pull the lever toward you. When you release the lever, the wipers make two or three more sweeps before stopping.

The wiper motor is equipped with a breaker that may stop motor operation temporarily to prevent an overload. Wiper operation will return to normal within a few minutes, once the circuit has returned to normal.

2013 RDXuuOperating the Switches Around the Steering WheeluWipers and Washers

The rear wiper and washer can be used when the power mode is in ON.

If the wiper stops operating due to any obstacle such as the build-up of snow, park the vehicle in a safe place.

1Wipers and Washers

■ Wiper switch (OFF, INT, ON) Change the wiper switch setting according to the amount of rain.

Rotate the wiper switch to OFF, and set the power mode to ACCESSORY or VEHICLE OFF (LOCK), then remove the obstacle.

■ Washer ( Sprays while you rotate the switch to this position. Hold it to activate the wiper and to spray the washer. Once released, it stops operating after a few more sweeps.

■ Rear Wiper/Washer

a INT: Intermittent b ON: Continuous wipe c OFF d Washer

■ Operating in reverse When you shift the transmission to (R with the front wiper activated, the rear wiper operates automatically as follows even if its switch is off.

Front Wiper Position

Rear Wiper Operation

INT (Intermittent)

LO (Low speed wipe) HI (High speed wipe)

Intermittent

Continuous

QRG

TOC

Index

127

2013 RDXuuOperating the Switches Around the Steering WheeluBrightness Control

QRG

Brightness Control

Control Knob

When the power mode is in ON, you can use the brightness control knob to adjust instrument panel brightness. Brighten: Turn the knob to the right.

1Brightness Control

Instrument panel brightness varies, depending on whether the exterior lights are on or off. The instrument panel dims to reduce glare when they are on.

Dim: Turn the knob to the left.

You will hear a beep when the brightness reaches minimum or maximum. The multi- information display will return to its original state several seconds after you adjust the brightness.

■ Brightness level indicator The brightness level is shown on the multi- information display while you are adjusting it.

When it is bright outside and the headlight integration with the wiper is activated, the instrument panel brightness does not change.

Pressing the display.

(SEL/RESET) knob switches the

If you turn the knob to the right until the brightness display is up to max, a beep sound. This cancels the reduced instrument panel brightness when the exterior lights are on.

TOC

Index

128

2013 RDXuuOperating the Switches Around the Steering WheeluRear Defogger/Heated Door Mirror Button

Rear Defogger/Heated Door Mirror Button Press the rear defogger and heated door mirror button to defog the rear window and mirrors when the power mode is in ON.

The rear defogger and heated door mirrors automatically switch off after 10-30 minutes depending on the outside temperature. However, if the outside temperature is 0°C or below, they do not automatically switch off.

1Rear Defogger/Heated Door Mirror Button

NOTICE When cleaning the inside of the rear window, be careful not to damage the heating wires. It is critical to wipe the window from side to side along the defogger heating wires.

This system consumes a lot of power, so turn it off when the window has been defogged. Also, do not use the system for a long period when the engine is idling. This may weaken the battery, making it difficult to start the engine.

QRG

TOC

Index

129

2013 RDXuuOperating the Switches Around the Steering WheeluDriving Position Memory System

QRG

Driving Position Memory System You can store two driver’s seat and door mirror positions with the driving position memory system. When you unlock and open the driver’s door with a remote transmitter, the seat and door mirrors adjust automatically to one of the two preset positions.

1Driving Position Memory System

Using the multi-information display, you can disable the automatic seat adjustment function.

2 Customized Features P. 87

The multi-information display shows you which remote transmitter you used to unlock the vehicle when you enter.

TOC

• Driver 1 transmitter is linked to memory button 1.

• Driver 2 transmitter is linked to memory button 2.

Driver 1

Driver 2

Index

130

2013 RDXuuOperating the Switches Around the Steering WheeluDriving Position Memory System

■ Storing a Position in Memory

Memory Button 1

Memory Button 2

SET Button

1. Set the power mode to ON. Adjust the driver’s seat and the door mirrors to the desired position.

2. Press the SET button.

uYou will hear a beep, and the memory

button indicator light will blink.

3. Press and hold memory button (1 or (2

within five seconds of pressing the SET button. uOnce the seat and the door mirrors position has been memorized, the indicator light on the button you pressed stays on.

■ Recalling the Stored Position

Memory Button 1

Memory Button 2

SET Button

1. Move the shift lever to (P. 2. Apply the parking brake. 3. Press a memory button ((1 or (2).

uYou will hear a beep, and the indicator

light will blink.

The seat and the door mirrors will automatically move to the memorized positions. When they have finished moving, you will hear a beep, and the indicator light stays on.

1Storing a Position in Memory

After you press the SET button, the storing operation will be canceled when: • You do not press the memory button within five

seconds.

• You readjust the seat position before the double-

beep.

• You readjust the door mirrors. • You set the power mode to any position except

ON.

1Recalling the Stored Position

The seat and the door mirrors will stop moving if you: • Press the SET button, or a memory button ((1 or

(2).

• Adjust the seat position. • Adjust the door mirrors. • Shift into any position except (P.

QRG

TOC

Index

131

2013 RDX1Adjusting the Steering Wheel

3WARNING

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

Make any steering wheel adjustments before you start driving.

uuOperating the Switches Around the Steering WheeluAdjusting the Steering Wheel

QRG

Adjusting the Steering Wheel The steering wheel height and distance from your body can be adjusted so that you can comfortably grip the steering wheel in an appropriate driving posture.

To adjust

To lock

Lever

1. Pull the steering wheel adjustment lever up.

u The steering wheel adjustment lever is

under the steering column.

2. Move the steering wheel up or down, and

in or out. u Make sure you can see the instrument

panel gauges and indicators.

3. Push the steering wheel adjustment lever

down to lock the steering wheel in position. u After adjusting the position, make sure

you have securely locked the steering wheel in place by trying to move it up, down, in, and out.

TOC

Index

132

2013 RDXAdjusting the Mirrors

Interior Rearview Mirror Adjust the angle of the rearview mirror when you are sitting in the correct driving position.

■ Automatic Dimming Rearview Mirror

When driving after dark, the automatic dimming rearview mirror reduces the glare from headlights behind you. Press the auto button to turn this function on and off. When activated, the auto indicator comes on.

Indicator

Auto Button

Sensor

1Adjusting the Mirrors

Keep the inside and door mirrors clean and adjusted for best visibility.

Adjust the mirrors before you start driving. 2 Adjusting the Seat Positions P. 136

1Automatic Dimming Rearview Mirror

The auto dimming function cancels when the shift position is in (R.

QRG

TOC

Index

133

2013 RDXuuAdjusting the MirrorsuPower Door Mirrors

QRG

Power Door Mirrors

Adjustment Switch

Selector Switch

■ Reverse Tilt Door Mirror

Selector Switch

You can adjust the door mirrors when the power mode is in ON.

■ Mirror position adjustment L/R selector switch: Select the left or right mirror. After adjusting the mirror, return the switch to the center position.

Mirror position adjustment switch: Press the switch left, right, up, or down to move the mirror.

If activated, either side door mirror automatically tilts downward when you put the shift lever in (R; this improves close-in visibility on the selected side of the vehicle when reversing. The mirror automatically returns to its original position when you shift out of (R.

To activate this feature, set the power mode to ON, and slide the selector switch to the left or right side.

TOC

Index

134

2013 RDX■ Expanded View Driver’s Mirror

Inner Segment

Outer Segment

The driver side door mirror has outer and inner segments. The outer segment is slightly curved to provide a wider angle view than a standard flat mirror. This wider view may help you check areas that are not visible using a standard door mirror.

uuAdjusting the MirrorsuPower Door Mirrors

1Expanded View Driver’s Mirror

Objects visible in the outer segment of the driver side door mirror appear smaller than objects in the rest of the mirror. But in fact, they are closer than they appear.

Do not rely on your mirrors. Always look to the side and behind your vehicle before changing lanes.

QRG

TOC

Index

135

2013 RDXAdjusting the Seats

QRG

Adjusting the Seat Positions

Allow sufficient space.

Adjust the driver's seat as far back as possible while allowing you to maintain full control of the vehicle. You should be able to sit upright, well back in the seat and be able to adequately press the pedals without leaning forward, and grip the steering wheel comfortably. The passenger's seat should be adjusted in a similar manner, so that it is as far back from the front airbag in the dashboard as possible.

1Adjusting the Seats

3WARNING

Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate.

Always sit as far back from the front airbags as possible while maintaining control of the vehicle.

Move back.

■ Adjusting the front power seats

Horizontal Position Adjustment

Height Adjustment (Driver’s seat only)

The National Highway Traffic Safety Administration and Transport Canada recommend that drivers allow at least 10 inches (25 cm) between the center of the steering wheel and the chest.

Always make seat adjustments before driving.

Lumbar Support Adjustment (Driver’s seat only)

Seat-back Angle Adjustment

TOC

Index

136

2013 RDX■ Adjusting the Seat-Backs

Adjust the driver's seat-back to a comfortable, upright position, leaving ample space between your chest and the airbag cover in the center of the steering wheel.

The front seat passenger should also adjust their seat-back to a comfortable, upright position.

Reclining a seat-back so that the shoulder part of the belt no longer rests against the occupant's chest reduces the protective capability of the belt. It also increases the chance of sliding under the belt in a crash and being seriously injured. The farther a seat-back is reclined, the greater the risk of injury.

uuAdjusting the SeatsuAdjusting the Seat Positions

1Adjusting the Seat-Backs

3WARNING

Reclining the seat-back too far can result in serious injury or death in a crash.

Adjust the seat-back to an upright position, and sit well back in the seat.

Do not put a cushion, or other object, between the seat-back and your back. Doing so may interfere with proper seat belt or airbag operation.

If you cannot get far enough away from the steering wheel and still reach the controls, we recommend that you investigate whether some type of adaptive equipment may help.

Continued

QRG

TOC

Index

137

2013 RDXuuAdjusting the SeatsuAdjusting the Seat Positions

■ Adjusting the Head Restraints

Your vehicle is equipped with head restraints in all seating positions.

Head restraints are most effective for protection against whiplash and other rear- impact crash injuries when the center of the back of the occupant's head rests against the center of the restraint. The tops of the occupant's ears should be level with the center height of the restraint.

Position head in the center of the head restraint.

■ Adjusting the front and rear outer head restraint positions

To raise the head restraint: Pull it upward. To lower the head restraint: Push it down while pressing the release button.

1Adjusting the Head Restraints

3WARNING

Improperly positioning head restraints reduces their effectiveness and increases the likelihood of serious injury in a crash.

Make sure head restraints are in place and positioned properly before driving.

For the head restraint system to work properly: • Do not hang any items on the head restraints, or

from the restraint legs.

• Do not place any object between an occupant and

the seat-back.

• Install each restraint in its proper location.

QRG

TOC

Index

138

2013 RDXuuAdjusting the SeatsuAdjusting the Seat Positions

■ Changing the Rear Center Seat Head Restraint Position

A passenger sitting in a center back seating position should adjust the height of their head restraint to an appropriate position before the vehicle begins moving. To raise the head restraint: Pull it upward.

To lower the head restraint: Push it down while pressing the release button.

■ Removing and Reinstalling the Head Restraints Head restraints can be removed for cleaning or repair.

To remove a head restraint: Pull the restraint up as far as it will go. Then push the release button, and pull the restraint up and out.

To reinstall a head restraint: Insert the legs back in place, then adjust the head restraint to an appropriate height while pressing the release button. Pull up on the restraint to make sure it is locked in position.

1Removing and Reinstalling the Head Restraints 3WARNING

Failure to reinstall, or correctly reinstall, the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

Continued

QRG

TOC

Index

139

2013 RDXuuAdjusting the SeatsuAdjusting the Seat Positions

■ Maintain a Proper Sitting Position After all occupants have adjusted their seats and head restraints, and put on their seat belts, it is very important that they continue to sit upright, well back in their seats, with their feet on the floor, until the vehicle is safely parked and the engine is off.

Sitting improperly can increase the chance of injury during a crash. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.

In addition, an occupant who is out of position in the front seat can be seriously or fatally injured in a crash by striking interior parts of the vehicle or being struck by an inflating front airbag.

1Maintain a Proper Sitting Position

3WARNING

Sitting improperly or out of position can result in serious injury or death in a crash.

Always sit upright, well back in the seat, with your feet on the floor.

QRG

TOC

Index

140

2013 RDXuuAdjusting the SeatsuRear Seats

Rear Seats ■ Folding Down the Rear Seats Separately fold down the left and right halves of the rear seat to make room for cargo.

■ To fold down the seat 1. Store the center seat belt first. Insert the latch plate into the slot on the side of the

anchor buckle.

2. Retract the seat belt into the holder on the ceiling.

2 Seat Belt with Detachable Anchor P. 34

3. Lower the center head restraint to its lowest position. Put the armrest back into

the seat-back.

From the rear door side 4. Pull the release lever.

Pull

1Folding Down the Rear Seats