2008 Volvo S80 Owners Manual

seconds except the

75 03 Your driving environment

Instruments and controls

symbol for faults in the vehicle's emissions system and the symbol for low oil pressure.

Certain symbols may not have their functions illustrated, depending on the vehicle's equipment.

Indicator and warning symbols

Trailer turn signal indicator

If you are towing a trailer, this light will flash simultaneously with the trailer's turn signals. If the light does not flash, or if they flash faster than usual when signaling a turn, the turn signals on the trailer or on the vehicle are not functioning properly.

Malfunction Indicator Light

As you drive, a computer called On- Board Diagnostics II (OBDII) monitors your vehicle's engine, transmission, electrical and emission systems.

The malfunction indicator (CHECK ENGINE) light will illuminate if the computer senses a condition that potentially

may need correcting. When this happens, please have your vehicle checked by a trained and qualified Volvo service technician as soon as possible.

A malfunction indicator (CHECK ENGINE) light may have many causes. Sometimes, you may not notice a change in your car's behavior. Even so, an uncorrected condition could hurt fuel economy, emission controls, and drivability. Extended driving without correcting the cause could even damage other components in your vehicle.

Canadian models are equipped with this symbol:

Anti-lock Brake System (ABS) warning light

If the warning light comes on, there may be a malfunction in the ABS system (the standard braking system will still function). Check the system by:

1. Stopping in a safe place and switching off the ignition.

76 03 Your driving environment

Instruments and controls

2. Restart the engine.

3. If the warning light goes off, no further action is required.

If the warning light remains on, the vehicle should be driven to a trained and qualified Volvo service technician for inspection. See page 113 for additional information.

Canadian models are equipped with this symbol:

Rear fog light

This symbol indicates that the rear fog light (located in the driver's side tail light cluster) is on.

Stability system

This indicator symbol flashes when the DSTC (Dynamic Stability and Traction Control system) is actively working to stabilize the vehicle. See page 151 for more detailed information.

Tire pressure monitoring system (TPMS) - option

This symbol illuminates to indicate that tire pressure in one or more tires is low. See page 242 for detailed information.

Low fuel level

When this light comes on, there are approximately 2.1 US gallons (8 liters) of fuel remaining in the tank.

Information symbol

The information symbol illuminates and a text message is displayed if a fault is detected in one of the vehicle's systems. The message can be erased and the symbol can be turned off by pressing the READ button (see page 124 for information) or this will take place automatically after a short time (the length of time varies, depending on the function affected).

The information symbol may also illuminate together with other symbols.

High beam indicator

This symbol illuminates when the high beam headlights are on, or if the high beam flash function is used.

Left turn signal indicator

Right turn signal indicator

NOTE

Both turn signal indicators will flash when the hazard warning flashers are used. If either of these indicators flash faster than normal, the direction indicators are not functioning properly.

Indicator and warning symbols

Low oil pressure

If the light comes on while driving, stop the vehicle, stop the engine immediately, and check the engine oil level. If the oil level is normal and the light stays on after restart, have the vehicle towed to the nearest trained and qualified Volvo service technician. This is normal, provided it goes off when the engine speed is increased.

Parking brake applied

This symbol illuminates when the parking brake is applied. On models

77 03 Your driving environment

Instruments and controls

equipped with the electric parking brake, this symbol flashes while the brake is being applied and then glows steadily.

A flashing symbol means that a fault has been detected. See the message in the information display.

Canadian models are equipped with this symbol:

NOTE

This symbol also comes on when the mechanical parking brake is only slightly applied.

Airbags - SRS

If this light comes on while the vehicle is being driven, or remains on for longer than approximately 10 seconds after the vehicle has been started, the SRS system's diagnostic functions have detected a fault in a seat belt lock or pretensioner, a front airbag, side impact airbag, and/or an inflatable curtain. Have the system(s) inspected by a trained and qualified Volvo service technician as soon as possible.

Seat belt reminder

This symbol comes on for approximately 6 seconds if the driver has not fastened his or her seat belt.

Generator not charging

This symbol comes on during driving if a fault has occurred in the electrical system. Contact an authorized Volvo workshop.

Engine temperature Engine overheating can result from low oil or coolant levels, towing or hard driving at high heat and altitude, or mechanical malfunction. Engine overheating will be signaled with text and a red warning triangle in the middle of the instrument display. The exact text will depend on the degree of overheating. It may range from "HIGH ENGINE TEMP - SLOW DOWN" to "HIGH ENGINE TEMP - STOP ENGINE." If appropriate, other messages, such as "COOLANT LEVEL LOW" will also be displayed. If your engine does overheat so that you must stop the engine, always allow the engine to cool before attempting to check oil and coolant levels.

Fault in brake system

If this symbol lights, the brake fluid level may be too low. Stop the vehicle in a safe place and check the level in the brake fluid reservoir, see page 211. If the level in the reservoir is below MIN, the vehicle should be transported to an authorized Volvo workshop to have the brake system checked.

If the brake and ABS symbols come on at the same time, there may be a fault in the brake force distribution system.

1. Stop the vehicle in a safe place and turn off the engine.

2. Restart the engine.

If both symbols extinguish, continue driving. If the symbols remain on, check the level in the brake fluid reservoir. See page 211. If the brake fluid level is

normal but the symbols are still lit, the vehicle can be driven, with great care, to an authorized Volvo workshop to have the brake system checked.

If the level in the reservoir is below MIN, the vehicle should be transported to an authorized Volvo workshop to

have the brake system checked.

WARNING

If the fluid level is below the MIN mark in the reservoir or if a warning message is displayed in the text window:

DO NOT DRIVE. Have the vehicle towed to a trained and qualified Volvo service technician and have the brake system inspected.

If the ABS and Brake system lights are on at the same time, there is a risk of reduced vehicle stability.

78 03 Your driving environment

Instruments and controls

Warning symbol

The red warning symbol comes on when a fault has been indicated which could affect the safety and/or drivability of the vehicle. An explanatory text is shown on the information display at the same time. The symbol remains visible until the fault has been rectified but the text message can be cleared with the READ button, see page 124. The warning symbol can also come on in conjunction with other symbols.

Action:

1. Stop in a safe place. Do not drive the vehicle further.

2. Read the information on the information display. Implement the action in accordance with the message in the display. Clear the message using READ.

Reminder - doors not closed If one of the doors, the hood or trunk lid is not closed properly, the information or warning symbol comes on together with an explanatory text message in the instrument panel. Stop the vehicle in a safe place as soon as possible and close the door, hood or trunk.

If the vehicle is driven at a speed lower than approximately 5 mph (7 km/h), the information symbol comes on.

If the vehicle is driven at a speed higher than approximately 5 mph (7 km/h), the warning symbol comes on.

Trip odometers

Odometer display

Button for toggling between T1 and T2, and for resetting the odometer.

The trip odometers are used to measure short distances. A short press the button toggles between the two trip odometers T1 and T2. A long press (more than 2 seconds) resets an active trip odometer to zero. The distance is shown in the display.

79 03 Your driving environment

Instruments and controls

Clock

 Display

Control for setting the clock.

Turn the control clockwise/counterclockwise to set the time. The set time is shown in the information display.

The clock may be temporarily replaced by a symbol in conjunction with a message, see page 124.

80 03 Your driving environment

Ignition modes

Functions

Inserting and removing the remote key The various ignition modes are accessed by inserting the remote key into the ignition slot.

The remote key can be removed from the ignition slot by pressing the key in. It will then be ejected slightly and can be removed from the slot.The gear selector must be in position P (Park).

NOTE

The brake pedal must not be depressed when accessing ignition modes I or II.

CAUTION

Foreign objects in the ignition slot can impair function or damage the lock.

Ignition mode 0

Insert the remote key in the ignition slot.

Ignition mode I Press the remote key into the ignition slot and press START/STOP ENGINE.

Ignition mode II Press the remote key into the ignition slot and press START/STOP ENGINE for approx. 2 seconds.

Ignition mode III (engine start) Start the engine, see page 107.

Stopping the engine Press START/STOP ENGINE. (If the engine is running and the vehicle is moving, keep the button depressed until the engine stops).

Return to ignition mode 0
Press START/STOP ENGINE to return from I, II, or III to ignition mode 0.

NOTE

During towing, ignition mode II should be used so that the lighting can be switched on.

81 03 Your driving environment

Ignition modes

Functions with timer The audio system can be operated without a key for 15 minutes at a time by pressing the POWER button. The power windows work for several minutes after the key has been removed, although not after the door has been opened.

NOTE

Use the POWER button for the audio system when the engine is not running to avoid discharging the battery.

82 03 Your driving environment

Seats

Front seats

Lumbar support: turn the control for firmer or softer lumbar support.

Front-rear adjustment: lift the bar and move the seat to the position of your choice.

Raise/lower front edge of seat cushion, pump up/down.

Backrest tilt: turn the control to adjust the angle of the backrest.

Raise/lower the seat, pump up/down.

Control panel for power seat.

WARNING

Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In

addition, position the seat as far rearward as comfort and control allow.

Check that the seat is securely locked into position after adjusting.

Folding the front seat backrest

The front passenger seat backrest can be folded to a horizontal position to make room for a long load. Fold the backrest as follows:

Move the seat as far back as possible.

Adjust the backrest to an upright position.

Lift the catches on the rear of the backrest.

Without releasing the catches, push the backrest forward.

Move the seat as far forward as possible so that the head restraint slides under the glove compartment.

WARNING

Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during sudden stops.

83 03 Your driving environment

Seats

Power seat

Front edge of seat cushion up/down

Seat forward/backward and up/down

Backrest tilt

Operation The seats can be adjusted for a short period after unlocking the door with the remote control without the key in the ignition slot. Seat adjustment is normally made when the ignition is on and can always be made when the engine is running.

NOTE

Only one of the power seat's controls can be used at the same time. The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch

off the ignition (key in position 0) and wait for a short period before operating the seat again.

Seat with memory function (option)

Stored seat position

Stored seat position

Stored seat position

Memory button

Programming the memory The following example explains how button 1 can be programmed. Buttons 2 and 3 can be programmed in the same way.

To program (store) a seat position and door mirror position in button 1:

1. Move the seat (and door mirrors) to the desired position using the seat and mirror adjustment controls.

2. Press and hold down the M (memory) button.

3. With the memory button depressed, press the button 1 briefly to store the current position for the seat/mirrors.

To move the seat and mirrors to the position that they were in when a button was programmed: 1. Press and hold down button 1 until the seat and mirrors stop moving.

NOTE

As a safety precaution, the seat will stop automatically if the button is released before the seat has reached the preset position.

84 03 Your driving environment

Seats

Remote keyless entry system and the driver's seat The remote control transmitter also controls the position of the power driver's seat in the following way:

1. Adjust the seat to your preferences.

2. When you leave your vehicle, lock it using the remote control.

The position of the driver's seat is now stored in the remote control's memory.

Automatic seat adjustment To move the seat to the position in which you left it:

1. Unlock the driver's door with the same remote control (the one used to lock the doors)

2. Open the driver's door within 2 minutes.

The driver's seat will automatically move to the position in which you left it.

NOTE

The key memory is independent of the seat memory. The seat will Move to this position even if someone else has moved it to a different seating position and locked

the vehicle with a different remote control.

This feature will work in the same way with all of the remote control transmitters that you use with your vehicle.

The function can be activated/deactivated under Car key memory menu system, see the information beginning on page 123.

Seat & mirror positions. For a description of the

Emergency stop If the seat accidentally begins to move, press one of the buttons to stop the seat.

WARNING

Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in the

vehicle.

Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel. Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In

addition, position the seat as far rearward as comfort and control allow.

The seat rails on the floor must not be obstructed in any way when the seat is in motion.

Heated/ventilated seats (option) See page 129.

85 03 Your driving environment

Seats

Rear seats

Folding down the rear seat backrests

The rear seat backrests can be folded down together, or separately, to make it easier to transport long objects.

1. Pull the release control handle(s).

2. Fold the backrest forward. Adjust the center seat head restraint if necessary.

NOTE

The outboard head restraints must be folded up (in the upright position) before lowering the backrests.

WARNING

Keep vehicle doors and the trunk locked and keep keys out of a child's reach. Unsupervised children could lock

themselves in an open trunk and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people to these

high temperatures for even a short period of time can cause heat-related injury or death. Small children are particularly at risk.

WARNING

When the backrest is returned to the upright position, check that it is properly locked in place. Return the head

restraints to the upright position.

Long loads should always be securely anchored to help avoid injury in the event of a sudden stop. Always turn the engine off and apply the parking brake when loading/unloading the vehicle. Place the transmission in the Park (P) position to help prevent inadvertent movement of the gear selector. The vehicle features a 60/40 split fold-down rear seat. The backrest(s) can be folded down by pulling the release

control handles inside the trunk.

Rear center head restraint

The center head restraint should be adjusted according to the passenger's height. The restraint should be carefully adjusted to support the occupant's head.

Pull the head restraint up as required. To lower, press the button at the base of the head restraint's left support while pressing the head restrain down.

WARNING

The center rear seat head restraint should only be in its lowest position when this seat is NOT occupied. When the center position is occupied, the head restraint should be correctly adjusted to the passenger's height.

86 03 Your driving environment

Seats

Automatically lowering the rear seat's outboard head restraints

1. The ignition must be in mode I or II.

2. Press the button to lower the rear head restraints for improved visibility.

NOTE

The head restraint must be returned to the upright position manually. The outboard head restraints cannot be folded down on models that are not equipped with this button.

WARNING

For safety reasons, no one should be allowed to sit in the outboard rear seat positions if the head restraints are folded down. If these positions are occupied, the head restraints should be in the upright (fixed) position.

87 03 Your driving environment

Steering wheel

Adjusting

Lever for releasing/locking the steering wheel

Possible positions

The steering wheel can be adjusted for both height and reach:

1. Pull the lever toward you to release the steering wheel.

2. Adjust the steering wheel to the position that suits you.

3. Push back the lever to fix the steering wheel in place. If the lever is difficult to push into place, press the steering wheel lightly at the same time as you push the lever.

WARNING

Never adjust the steering wheel while driving.

With speed-dependent power steering (option) the level of steering force can be adjusted, see page 153.

Keypads

Cruise control, see page 154

Adaptive cruise control (option), see page 156.

Audio controls, see page 122.

88 03 Your driving environment

Steering wheel

Horn

Press the steering wheel hub to sound the horn.

89 03 Your driving environment

Lighting

Lighting panel

Thumb wheel for adjusting display and instrument lighting

Rear fog light

Front fog lights

Headlights/parking lights

Instrument lighting Illumination of the display and instrument lights will vary, depending on ignition mode.

The display lighting is automatically subdued in darkness and the sensitivity is set with the thumb wheel.

The intensity of the instrument lighting is adjusted with the thumb wheel.

High/low beam headlights

Low beams When the engine is started, the low beams are activated automatically (daytime running lights) if the headlight control is in position

or

Daytime running lights can be deactivated by an authorized Volvo workshop.

NOTE

The use of daytime running lights is mandatory in Canada. Continuous high beams cannot be activated when the headlight switch is in position

or

. High beam

flash will function in these positions.

High beam flash Move the lever toward the steering wheel to position

. The high beams come on until the lever is released.

High/low beam headlights Continuous high beams Set the ignition to mode II.

With the light switch in position between high and low beams (this also applies on models equipped with the optional Active Bi-Xenon® headlights).

, pull the turn signal lever toward the steering wheel to position

to toggle

The

symbol illuminates in the instrument panel to indicate that the high beams are on.

90 03 Your driving environment

Lighting

Active Bi-Xenon® Lights (ABL)-option

When the ABL function is activated, the headlight beams adjust laterally to help light up a curve according to movements of the steering wheel (see the right-pointing beam in the illustration).

This function is activated automatically when the engine is started and can be deactivated/reactivated by pressing the ABL button there is a fault in the system.

in the center console. This button lights up when the ABL function is activated, and will flash if

NOTE

This function is only active in twilight or dark conditions, and only when the vehicle is in motion.

Parking lights

The front and rear parking lights can be turned on even when the ignition is switched off.

Turn the headlight control to the center position (the license plate lighting comes on at the same time).

The lighting also comes on when the trunk lid is opened in order to alert anyone traveling behind your vehicle.

91 03 Your driving environment

Lighting

Brake lights

The brake lights come on automatically when the brakes are applied.

Emergency brake lights (EBL) Emergency Brake Lights, EBL, activate in the event of sudden braking or if the ABS system is activated. This function causes an additional taillight on each side of the vehicle to illuminate to help alert vehicles traveling behind.

The EBL function activates if:

The ABS system activates for more than approximately a half second In the event of sudden braking while the vehicle is moving at speeds above approximately 6 mph (10 km/h)

When the vehicle has come to a stop, the brake lights and additional taillights remain on for as long as the brake pedal is depressed or until braking force on the vehicle is reduced.

Front fog lights

The front fog lights can be switched on together with high/low beams or the parking lights.

Press the button to switch the fog lights on/off. The light in the button comes on when the fog lights are on.

NOTE

Regulations regarding the use of the front fog lights may vary, depending on where you drive.

Rear fog light

The single rear fog light is located in the driver's side taillight cluster.

The rear fog light will only function in combination with the high/low beam headlights or the optional front fog lights.

Press the button to switch the rear fog light on/off. The rear fog light indicator symbol and the light in the button come on when the rear fog light is switched on.

on the instrument panel

92 03 Your driving environment

Lighting

NOTE

The rear fog light is considerably brighter than the normal tail lights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters).

Hazard warning flashers

The hazard warning flasher should be used to indicate that the vehicle has become a traffic hazard. To activate the

flashers, press the button in the center dash. Press the button again to turn off the flashers.

NOTE

Regulations regarding the use of the hazard warning flasher may vary, depending on where you live. The hazard warning flashers will be activated automatically if an airbag deploys.

Turn signals

When changing lanes

position and releasing it.

The driver can automatically flash the turn signals 3 times by moving the turn signal lever up or down to the first

When turning

Move the lever as far up or down as possible to start the turn signals. The turn signals will be cancelled

automatically by the movement of the steering wheel, or the lever can be returned to its initial position by hand.

93 03 Your driving environment

Lighting

NOTE

This automatic flashing sequence can be interrupted by immediately moving the lever in the opposite direction. If the turn signal indicator flashes faster than normal, check for a burned-out turn signal bulb.

Interior lighting, front

Drivers side front reading light, on/off

Passenger's side front reading light, on/ off

Overhead courtesy lighting.

The lighting in the front part of the passenger compartment is controlled with the buttons

and

in the roof console.

Switch

has three positions for all passenger compartment lighting:

Off - right side depressed, automatic lighting off. Neutral position. On - left side depressed, passenger compartment lighting on.

Interior lighting, rear

The lights are switched on or off by pressing each respective button.

Courtesy lights/door step lighting (option) The courtesy lights/door step lighting switch on/off automatically when one of the front doors is opened/closed.

Glove compartment lighting The glove compartment lighting switches on/off automatically when the lid is opened/closed.

94 03 Your driving environment

Lighting

Overhead courtesy lighting The passenger compartment lighting is switched on and off automatically when button

is in the neutral position.

The lighting comes on and remains on for 30 seconds if:

the vehicle is unlocked from the outside with the key or remote control the engine is switched off and the ignition is in mode 0.

The lighting switches off when:

the engine is started the vehicle is locked from the outside.

The lighting comes on and remains on for two minutes if one of the doors is open.

The passenger compartment lighting can be switched on and off manually within 30 minutes after the vehicle has been unlocked.

If the lighting is switched on manually and the vehicle is locked, the courtesy lighting will switch off automatically after one minute.

Home safe lighting

When you leave your vehicle at night, you can make use of the home safe lighting function to illuminate the area in front of the vehicle.

1. Remove the key from the ignition slot.

2. Pull the direction indicator lever as far as possible towards the steering wheel and release it.

3. Exit the vehicle and lock the doors.

The headlights, parking lights, turn signals, lights in the door mirrors, license plate lights, and footwell lighting will illuminate and remain on for 301, 60 or 90 seconds. The time interval can be set under Car settings Light settings Home safe lighting. For a description of the menu system, see page 123.

1Factory setting

Approach lighting

Approach lighting is activated by pressing the approach light button on the remote key (see the illustration on page 54).

When the function has been activated, the parking lights, indicator lights, door mirror lights, license plate lighting, dome lighting and door step lighting come on.

The time interval for this lighting can be set under Car settings Light settings Approach lighting. For a description of the menu system, see page 123.

Contents | Top of Page

2 0 0 8
VOLVO

S80

95 03 Your driving environment

Wipers and washers

Windshield wipers/washers

Rain sensor on/off

Thumb wheel sensitivity/frequency

Windshield wipers off

Move the lever to position 0 to switch off the windshield wipers.

Single sweep

Move the lever upward from position 0 to sweep the windshield one stroke at a time for as long as the lever is held up.

Intermittent wiping

With the lever in this position, you can set the wiper interval by twisting the thumb wheel upward to increase wiper speed or downward to decrease the speed.

Continuous wiping

wipers operate at normal speed.

The wipers operate at high speed.

Rain sensor (option) The rain sensor automatically regulates wiper speed according to the amount of water on the windshield.The sensitivity of the rain sensor can be adjusted moving the thumb wheel up (the wipers will sweep the windshield more frequently) or down (the wipers will sweep the windshield less frequently).

NOTE

The wipers will make an extra sweep each time the thumb wheel is adjusted upward.

When the rain sensor is activated, the symbol

will illuminate in the instrument panel.

Activating and setting the sensitivity When activating the rain sensor, the vehicle must be running or in ignition mode II and the windshield wiper lever must be in position 0 or in the single sweep position.

Activate the rain sensor by pressing the button

. The windshield wipers will make one sweep.

Press the lever up for the wipers to make an extra sweep. The rain sensor returns to active mode when the stalk is released back to position 0.

Deactivating Deactivate the rain sensor by pressing the button

or press the lever down to another wiper position.

The rain sensor is automatically deactivated when the key is removed from the ignition slot or five minutes after the ignition has been switched off.

CAUTION

Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers

Before using the wipers, ice and snow should be removed from the windshield. Be sure the wiper blades are not

are in operation.

frozen in place.

96 03 Your driving environment

Wipers and washers

Windshield washing

Move the lever toward the steering wheel to start the windshield and headlight washers. After the lever is released the wipers make several extra sweeps.

Heated washer nozzles (option) The washer nozzles are heated automatically in cold weather to help prevent the washer fluid from freezing.

High-pressure headlight washing (option) High-pressure headlight washing consumes a large quantity of washer fluid. To save fluid, the headlights are washed using two alternatives:

Low/high beam headlights on

Parking lights on

The headlights will be washed the first time the windshield is washed. Thereafter, the headlights will only be washed once for every five times the windshield is washed within a 10-minute period.

Optional Active Bi-Xenon® headlights will be washed once for every five times the windshield is washed. Normal halogen headlights will not be washed.

CAUTION

Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers are in operation.

NOTE

One headlight is washed at a time.

97 03 Your driving environment

Power windows

Power windows

Switch for power child safety locks1 and disengaging rear power window buttons, see page 48

Rear window controls

Front window controls.

WARNING

Always remove the ignition key when the vehicle is unattended. Never leave children unattended in the vehicle. Make sure that the windows are completely unobstructed before they are operated.

1Option on certain markets only.

Operating

Manual up/down

Auto up/down.

All power windows can be operated using the control panel in the driver's door. The control panels in the other doors only operate the window in the respective doors.

For the power windows to function, the ignition must be in at least mode I. When the vehicle has been running, the power windows can be operated for several minutes after the remote key has been removed from the ignition slot, or until a door has been opened.

NOTE

Movement of the windows will stop if they are obstructed in any way. To reduce buffeting wind noise if the rear windows are opened, also open the front windows slightly

Manual up/down Move one of the controls up/down gently. The power windows move up/down as long as the control is held in position.

Auto up/down Move one of the controls up/down as far as possible and release it. The window will open or close completely.

Resetting If the battery has been disconnected, the auto open function must be reset so that it will work properly.

1. Gently raise the front section of the button to close the window and hold it for one second.

2. Release the button briefly.

3. Raise the front section of the button again for one second.

98 03 Your driving environment

Power windows

Laminated glass (option on certain markets only)

This glass is reinforced to help provide protection against break-ins and improved sound insulation in the passenger compartment. The windshield and side windows have laminated glass.

99 03 Your driving environment

Mirrors

Power door mirrors

Adjusting 1. Press the L button for the left door mirror or the R button for the right door mirror. The light in the button comes on.

2. Adjust the position with the joystick in the center.

3. Press the L or R button again. The light should no longer be on.

WARNING

Objects seen in the mirrors may appear further away than they actually are.

Retractable power door mirrors (option on certain markets only) The mirrors can be retracted for parking/driving in narrow spaces:

1. Press down the L and R buttons at the same time.

2. Release them after approximately one second. The mirrors automatically stop in the fully retracted position.

Fold out the mirrors by pressing down the L and R buttons at the same time. The mirrors automatically stop in the fully extended position.

Storing the position (option) The mirror positions are stored in the key memory when the vehicle has been locked with the remote key. When the vehicle is unlocked with the same remote control the mirrors and the driver's seat adopt the stored positions when the driver's door is opened.

The function can be activated/deactivated under Car key memory menu system, see page 123.

Seat & mirror positions. For a description of the

Tilting the door mirrors when parking The door mirrors can be tilted down to help give the driver to a better view along the sides of the vehicle, for example when parallel parking. To activate this function, select reverse gear and press either the L or R mirror control button to tilt the mirror down.

The door mirror will reset to its normal position:

after 10 seconds when reverse is disengaged and the car remains stopped. immediately when reverse is disengaged and the vehicle's forward speed exceeds approximately 6 mph (10 km/h). immediately if you press the corresponding L or R button again. when the engine is turned off. when the side mirrors are folded in.

NOTE

Only one mirror can be tilted down at a time.

Automatic retraction when locking When the vehicle is locked/unlocked with the remote key the door mirrors are automatically retracted/extended.

The function can be activated/deactivated under Car settings Retract mirrors

100 03 Your driving environment

Mirrors

when locking. For a description of the menu system, see page 123.

Resetting to neutral Mirrors that have been moved out of position by an external force must be electrically reset to the neutral position for electric retracting/extending to work.

Retract the mirrors with the L and R buttons. Fold them out again with the L and R buttons.

The mirrors are now reset in neutral position.

Home safe and approach lighting The light on the door mirrors comes on when approach lighting or home safe lighting is selected, see page 94.

Rear window and door mirror defrosters

Use the defroster to quickly remove misting and ice from the rear window and the door mirrors.

Press the button once to start simultaneous rear window and door mirror defrosting. The light in the button indicates that the function is active. Defrosting is deactivated automatically and its duration is controlled by the outside

temperature.

The rear window is demisted/de-iced automatically if the vehicle is started in an outside temperature lower than + 7°C.

Defrosting can be selected under Climate settings Auto. rear defroster. Select between On or Off.

Interior rearview mirror

Auto-dim function An integrated sensor reacts to headlights from following traffic and automatically reduces glare in the mirror.

101 03 Your driving environment

Power moonroof

Power moonroof

The moonroof controls are located in the ceiling console near the rearview mirror. The moonroof can be opened vertically and horizontally. The vehicle's must be in ignition mode I or II for the moonroof to be operated.

Sliding moonroof

Opening, automatic

Opening, manual

Closing, manual

Closing, automatic

Automatic opening Pull the switch as far back as possible (to the position for automatic opening) and release it to automatically fully slide open the moonroof.

Manual opening Pull the switch back to the first stop (the position for manual opening)and hold it until the moonroof has opened to the position of your choice.

Manual closing Push the switch forward to the first stop (the position for manual closing) and hold it until the moonroof has closed to the position of your choice, or has closed completely.

Automatic closing Push the switch as far forward as possible (the position for automatic closing) and release it to automatically close the moonroof.

WARNING

During manual closing, if the moonroof is obstructed, immediately open it again. Never open or close the moonroof if it is obstructed in any way. Never allow a child to operate the moonroof. Never leave a child alone in a vehicle. Never extend any object or body part though the open moonroof, even if the vehicle's ignition is completely

switched off.

Tilt position

Opening Press the rear edge of the control upward to position

Closing Pull the rear edge of the control down to position

and hold it until the moonroof has closed completely.

CAUTION

Remove ice and snow before opening the moonroof. Do not operate the moonroof if it is frozen closed. Never place heavy objects on the moonroof.

102 03 Your driving environment

Power moonroof

Visor The moonroof features a sliding visor. The visor slides open automatically when the moonroof is opened, and must be closed manually.

103 03 Your driving environment

HomeLink® Universal Transceiver

Introduction

HomeLink1 is a system that can be programmed to learn the codes of three different remote controlled-devices (for example, a garage door opener, remote lighting, entry gate). HomeLink's sun visor-mounted transceiver, powered by your car's electrical system, may then be used in place of your handheld remote controls. The HomeLink transceiver consists of three programmable buttons and an indicator light.

1 HomeLink is a registered trademark of Johnson Controls, Intl. © JCI, All rights reserved

NOTE

For your security, the HomeLink Universal Transceiver is designed to not function if you lock your car from the

outside.

vehicle.

Retain the original transmitter(s) for future programming procedures (for example, if you purchase a new vehicle). For your own security, erase all programmed buttons on the HomeLink Universal Transceiver when you sell your

Metallic sun protection films should not be used on any windows in a vehicle equipped with HomeLink Universal

Transceiver. This could interfere with the transceivers function.

Operating the HomeLink Universal Transceiver Once programmed, the HomeLink Universal Transceiver can be used in place of your handheld transmitters.

NOTE

The HomeLink universal transceiver will function for 30 minutes after the driver's door has been opened without switching on the vehicle's ignition.

Press the programmed HomeLink button to activate the garage door, driveway gate, security lightning, home security system etc.

Your original hand-held transmitters may, of course, be used at any time.

WARNING

If you use HomeLink to open a garage door or gate, be sure no one is near the gate or door while it is in motion. Do not use the HomeLink Universal Transceiver with any garage door opener that lacks safety "stop" and

"reverse" features as required by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982). A garage door opener that cannot "detect" an object, signalling the door to "stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355-3515. (Internet: www.HomeLink.com).

Programming the transceiver for the first time (U.S. residents) 1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)

2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface

104 03 Your driving environment

HomeLink® Universal Transceiver

(located on your sun visor), keeping the HomeLink indicator light in view.

Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)

NOTE

Some garage door openers may require you to replace step 3 with the "cycling" procedure noted in the "Programming the transceiver for the first time (Canadian residents)" section.

3. Press and hold the trained HomeLink button and observe the indicator light.

If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink

button is pressed and released.

If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following

training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.

4. At the garage door opener receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener's manual or contact us toll-free 1-800-355-3515 (Internet: www.HomeLink.com).

5. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer).

NOTE

Once the button is pressed, there are 30 seconds in which to initiate the next step.

6. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.

To train additional HomeLink buttons, begin with step two.

Programming the transceiver for the first time (Canadian residents) 1. For first time training, press and hold the two outer HomeLink buttons releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.)

2. Position the hand-held transmitter 1-3 inches (2.5-7.5 cm) away from the HomeLink surface (located on your) keeping the HomeLink indicator light in view.

3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter

button. During programming, your handheld transmitter may automatically stop transmitting. Continue to press and hold the desired HomeLink button while you press and re-press ("cycle") your handheld transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)

105 03 Your driving environment

HomeLink® Universal Transceiver

4. Press and hold the trained HomeLink button and observe the indicator light.

If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.

If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following

training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.

5. At the garage door opener receiver (motorhead unit) in the garage, locate the "learn" or "smart" button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button reference the garage door opener's manual or contact us.

6. Press and release the "learn" or "smart" button (the name and color of the button may vary by manufacturer).

NOTE

Once the button is pressed, there are 30 seconds in which to initiate the next step.

7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the "press/hold/release" sequence up to 3 times to complete the training process.

NOTE

During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the desired HomeLink button while you press and repress ("cycle") your hand-held transmitter every two seconds until the frequency signal has been learned. The indicator light will flash slowly and then rapidly after several seconds upon successful training. If necessary, follow steps 5-7 to complete the training for a rolling code device.

To train additional HomeLink buttons, begin with step two.

Rolling Code Programming Rolling code garage door openers that are "code-protected" and manufactured after 1996 may be determined by the- following:

Reference the garage door opener owner's manual for verification. The handheld transmitter appears to program the HomeLink Universal Transceiver but does not activate the garage

door.

Press and hold the trained HomeLink button. The garage door opener has the rolling code feature if the indicator

light flashes rapidly and then turns solid after 2 seconds.

To train a garage door with the rolling code feature, follow these instructions (the aid of a second person may make the

training quicker and easier):

1. Locate the training button on the garage door opener motor head unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the garage door opener owner's manual or please visit our Web site at www.homelink.com.

2. Press the training button on the garage door opener motor head unit (which activates the "training light").

NOTE

Following step 2, there are 30 seconds in which to initiate step 3.

3. Firmly press and release the programmed HomeLink® button. Press and release the HomeLink button a second time to complete the training process. (Some garage door openers may require

106 03 Your driving environment

HomeLink® Universal Transceiver

you to do this procedure a third time to complete the training.)

The garage door opener should now recognize the HomeLink Wireless Control System. The remaining two buttons may now be trained if this has not previously been done. Refer to the Programming portion of this text. The HomeLink Wireless Control System (once programmed) or the original handheld transmitter may be used to activate the garage door. In the event that there are still difficulties in programming the HomeLink Wireless Control System, please visit our Web site, www.homelink.com.

Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps:

1. Press and hold the desired HomeLink button. Do NOT release until step 4 has been completed.

2. When the indicator light begins to flash slowly ( after 20 seconds), position the handheld transmitter 1 to 3 inches away from the HomeLink surface.

3. Press and hold the handheld transmitter button. The HomeLink indicator light will flash, first slowly and then rapidly.

4. When the indicator light begins to flash rapidly, release both buttons.

The previous device has now been erased and the new device can be activated by pushing the HomeLink button that has just been programmed. This procedure will not affect any other programmed HomeLink.

Erasing Channels Individual buttons cannot be erased. However, to erase all three programmed buttons:

1. Press and hold the two outside buttons until the indicator light begins to flash (after 20 seconds).

2. Release both buttons.

The HomeLink® Wireless Control System is now in the training (learning) mode and can be programmed at any time following steps 2 through 4 in the Programming section.

107 03 Your driving environment

Starting the engine

Starting the engine

Ignition switch with remote key inserted (see

page 80 for more information)

1. Fasten the seat belt.

WARNING

Before starting the engine, check that the seat, steering wheel and mirrors are adjusted properly. Make sure the brake pedal can be depressed completely. Adjust the seat if necessary.

2. Insert the remote key into the ignition slot. Press the key until it is drawn into the slot1.

NOTE

The remote key should be inserted into the ignition slot with the key blade end of the remote pointing out and the key pad facing up. See the illustration on page 80.

3. Depress the brake pedal2.

WARNING

An extra mat on the driver's floor can cause the accelerator and/or brake pedal to catch. Check that the movement of these pedals is not impeded. Not more than one protective floor covering may be used at one time.

4. Press and release the START/STOP ENGINE button. The autostart function will operate the starter motor until the engine starts.

The starter motor operates for a maximum of 10 seconds. If the engine has not started, repeat the procedure.

1On vehicles with the optional keyless drive, it is only necessary to have a remote control in the passenger's compartment. 2 If the vehicle is moving, it is only necessary to press the START/STOP ENGINE button to start the vehicle.

WARNING

Always remove the remote key from the ignition slot when leaving the vehicle, especially if there are children in

the vehicle.

Never remove the remote key from the ignition slot while driving or when the vehicle is being towed. The

steering lock could otherwise be activated, making it impossible to steer the vehicle. Never remove the remote key with keyless drive function (option) from the vehicle while driving or during towing.

Always place the gear selector in Park and apply the parking brake before leaving the vehicle. Never leave the

vehicle unattended with the engine running.

Always open garage doors fully before starting the engine inside a garage to ensure adequate ventilation. The

exhaust gases contain carbon monoxide, which is invisible and odorless but very poisonous.

108 03 Your driving environment

Starting the engine

NOTE

The idling speed can be noticeably higher than normal during cold starts. This is to enable emission control system

can reach normal operating temperature as quickly as possible, which helps reduce exhaust emissions1.

Keylock: Your vehicle is equipped with a keylock system. When the engine is switched off, the gear selector must

be in the Park position before the key can be removed2 from the ignition slot.

1If the gear selector is in the D or R positions and the car is not moving, engine speed (rpm) will be lower and it will take longer for the engine to reach normal operating temperature. 2Does not apply to vehicles with the optional keyless drive.

CAUTION

When starting in cold weather, the automatic transmission may shift up at slightly higher engine speeds than

normal until the automatic transmission fluid reaches normal operating temperature.

Do not race a cold engine immediately after starting. Oil flow may not reach some lubrication points fast enough

to prevent engine damage.

The engine should be idling when you move the gear selector. Never accelerate until after you feel the

transmission engage. Accelerating immediately after selecting a gear will cause harsh engagement and premature transmission wear.

Selecting P or N when idling at a standstill for prolonged periods of time will help prevent overheating of the

automatic transmission fluid.

Keyless drive (option) Follow steps 3-4 for starting the engine.

NOTE

For the vehicle to start, one of the vehicle's remote keys must be in the passenger compartment.

Steering wheel lock The steering wheel lock is deactivated when the remote key is inserted into the ignition slot1 and activated when the remote key is removed from the ignition slot.

Always take the remote key or keyless drive remote when leaving the vehicle to help reduce the risk of theft.

1 On vehicles with the optional keyless drive, the steering lock is deactivated when the start button is pressed for the first time (assuming that a

remote control is in the passenger's compartment). It is activated when the ignition is switched off and the driver's door is opened.

109 03 Your driving environment

Starting the engine

Jump starting

Follow these instructions to jump start your vehicle's dead battery or to jump start another vehicle's dead battery using your vehicle. If the 12-volt auxiliary battery to be used is in another vehicle, check that the vehicles are not touching to prevent premature completion of a circuit. Be sure to follow jump starting instructions provided for the other vehicle.

To jump start your vehicle:

1. Switch off the ignition (set the ignition to mode 0, see page 80).

2. First connect the red jumper cable to the auxiliary battery's positive (+) terminal

3. Fold back the cover over the positive (+) terminal on your vehicle's battery under a folding cover.

, marked with a "+" sign, located

4. Connect the black jumper cable to the auxiliary battery's negative (-) terminal vehicle's engine compartment (right engine mount at the top, on the outer screw)

and to the ground point in your

5. Start the engine in the assisting vehicle, then start the engine in the vehicle with dead battery.

6. After the engine has started, first remove the negative (-) terminal jumper cable (black). Then remove the positive (+) terminal jumper cable (red).

WARNING

PROPOSITION 65 WARNING!

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling.

CAUTION

Connect the jumper cables carefully to avoid short circuits with other components in the engine compartment.

WARNING

 Do not connect the jumper cable to any part of the fuel system or to any moving parts. Avoid touching hot

manifolds.

Batteries generate hydrogen gas, which is flammable and explosive. Battery fluid contains sulfuric acid. Do not allow battery fluid to contact eyes, skin, fabrics or painted surfaces. If contact occurs, flush the affected area immediately with water. Obtain medical help immediately if eyes are affected.

Never expose the battery to open flame or electric spark. Do not smoke near the battery. Failure to follow the instructions for jump starting can lead to injury.

110 03 Your driving environment

Transmission

Automatic transmission

Depress the button on the front of the gear selector knob to move the gear selector between the R, N, D, and P positions.

The gear selector can be moved freely between the Geartronic (manual shifting) and Drive (D) positions while driving.

Park position (P) Select the P position when starting or parking.

1The information display (see page 74) shows the gear selector's position or the selected gear by displaying the following: P, R, N, D, 1, 2, 3, 4, 5, or 6.

Keylock To remove the remote key from the ignition slot, the gear selector must be in the P position. The remote key is locked in the slot in all other positions.

Shiftlock When P has been selected, the transmission is mechanically blocked in this position. The brake pedal must be depressed before the gear lever can be moved from the P position.

Always apply the parking brake when the vehicle is parked, see page 116. If the vehicle is equipped with the optional electric parking brake, press the control to apply the brake, see page 116.

CAUTION

The vehicle must be stationary when position P is selected.

Reverse (R) The vehicle must be stationary when position R is selected.

Neutral position (N) No gear is engaged and the engine can be started with the gear selector in this position. Apply the parking brake if the vehicle is stationary with the gear selector in position N.

Drive (D) D is the normal driving position. The car automatically shifts between the various forward gears, based on the level of acceleration and speed. The car must be at a standstill when shifting from position R to position D.

111 03 Your driving environment

Transmission

Geartronic-manual shifting Geartronic allows you to manually shift among your vehicle's six forward speeds. Geartronic can be selected at any time.

To access the manual (M) shifting position from Drive (D), move the gear selector to the right to M. To return to the D position from M, move the gear selector to the left.

While driving

If you select the M position while driving, the gear that was being used in the Drive position will also initially be

selected in the M position.

gear.

Move the gear selector forward (toward "+") to shift to a higher gear or rearward (toward "-") to shift to a lower

If you hold the gear selector toward "-", the transmission will downshift one gear at a time and will utilize the

braking power of the engine. If the current speed is too high for using a lower gear, the downshift will not occur until the speed has decreased enough to allow the lower gear to be used.

If you slow to a very low speed, the transmission will automatically shift down.

Shiftlock - Neutral (N) If the gear selector is in the N position and the vehicle has been stationary for at least 3 seconds (irrespective of whether the engine is running) then the gear selector is locked.

To be able to move the gear selector from N to another gear position, the brake pedal must be depressed and the ignition must be in position II, see page 80.

Shiftlock override

If the vehicle cannot be driven, for example because of a dead battery, the gear selector must be moved from the P position so that the vehicle can be moved1.

Lift away the rubber mat on the floor of the storage compartment behind the center console and open the hatch.

Insert the key blade into the opening as far as possible. Press the key blade down and keep it held down. Move the

gear selector from the P position. For information on the key blade, see page 52.

1If the battery is dead, the optional electric parking brake cannot be applied or released. Connect an auxiliary battery if the battery voltage is too low, see page 109.

112 03 Your driving environment

Transmission

All Wheel Drive - AWD1
Your Volvo can be equipped with permanent All Wheel Drive, which means that power is distributed automatically between the front and rear wheels. Under normal driving conditions, most of the engine's power is directed to the front wheels. However, if there is any tendency for the front wheels to spin, an electronically controlled coupling distributes power to the wheels that have the best traction.

1Standard on certain models.

113 03 Your driving environment

Brakes

Brake system

The brake system is a hydraulic system consisting of two separate brake circuits. If a problem should occur in one of these circuits, it is still possible to stop the vehicle with the other brake circuit.

If the brake pedal must be depressed farther than normal and requires greater foot pressure, the stopping distance will be longer.

A warning light in the instrument panel will light up to warn the driver that a fault has occurred.

If this light comes on while driving or braking, stop immediately and check the brake fluid level in the reservoir.

 NOTE

Press the brake pedal hard and maintain pressure on the pedal - do not pump the brakes.

WARNING

If the fluid level is below the MIN mark in the reservoir or if a brake system message is shown in the information display: DO NOT DRIVE. Have the vehicle towed to a trained and qualified Volvo service technician and have the brake system inspected.

Power brakes function only when the engine is running The power brakes utilize vacuum pressure which is only created when the engine is running. Never let the vehicle roll to a stop with the engine switched off.

If the power brakes are not working, the brake pedal must be pressed approximately five times harder than usual to make up for the lack of power assistance. This can happen for example when towing your vehicle or if the engine is switched off when the vehicle is rolling. The brake pedal feels harder than usual.

Water on brake discs and brake pads affects braking Driving in rain and slush or passing through an automatic car wash can cause water to collect on the brake discs and pads. This will cause a delay in braking effect when the pedal is depressed. To avoid such a delay when the brakes are needed, depress the pedal occasionally when driving through rain, slush, etc. This will remove the water from the brakes. Check that brake application feels normal. This should also be done after washing or starting in very damp or cold weather.

Severe strain on the brake system The brakes will be subject to severe strain when driving in mountains or hilly areas, or when towing a trailer. Vehicle speed is usually slower, which means that the cooling of the brakes is less efficient than when driving on level roads. To reduce the strain on the brakes, shift into a lower gear and let the engine help with the braking. Do not forget that if you are towing a trailer, the brakes will be subjected to a greater than normal load.

Anti-lock braking system The Anti-lock Braking System (ABS) helps to improve vehicle control (stopping and steering) during severe braking conditions by limiting brake lockup. When the system "senses" impending lockup, braking pressure is automatically modulated in order to help prevent lockup that could lead to a skid.

The system performs a self-diagnostic test when the engine is started and when the vehicle first reaches a speed of approximately 12 mph (20 km/h). The brake pedal will pulsate several times and a sound may be audible from the ABS control module. This is normal.

114 03 Your driving environment

Brakes

Cleaning the brake discs Coatings of dirt and water on the brake discs may result in delayed brake function. This delay is minimized by cleaning the brake linings.

Cleaning the brake pads is advisable in wet weather, prior to long-term parking, and after the vehicle has been washed. Do this by braking gently for a short period while the vehicle is moving.

Emergency Brake Assistance

EBA is designed to provide full brake effect immediately in the event of sudden, hard braking. The system is activated by the speed with which the brake pedal is depressed.

When the EBA system is activated, the brake pedal will go down and pressure in the brake system immediately increases to the maximum level. Maintain full pressure on the brake pedal in order to utilize the system completely. EBA is automatically deactivated when the brake pedal is released.

NOTE

When the EBA system is activated, the brake pedal will go down and pressure in the brake system immediately increases to the maximum level. You must maintain full pressure on the brake pedal in order to utilize the system completely. There will be no braking effect if the pedal is released. EBA is automatically deactivated when the brake pedal is released.

When the vehicle has been parked for some time, the brake pedal may sink more than usual when the engine is

started. This is normal and the pedal will return to its usual position when it is released.

Symbols in the instrument panel

WARNING

and

come on at the same time and the brake level is below the MIN mark in the reservoir or if a If brake system-related message is shown in the information display: DO NOT DRIVE. Have the vehicle towed to a trained and qualified Volvo service technician and have the brake system inspected.

115 03 Your driving environment

Parking brake

Manual parking brake

The parking brake pedal indicator light illuminates in the instrument panel.

is located under the dashboard, to the left of the brake pedal. When the brake is applied, an

NOTE

The indicator light will light up even if the parking brake has only been partially applied.

Applying the parking brake 1. Press firmly on the brake pedal.

2. Press down pedal 1 firmly to its full extent.

3. Release the brake pedal and ensure that the vehicle is at a standstill.

4. If the vehicle rolls, the parking brake pedal must be pushed down more firmly.

5. When parking a vehicle always put the gear selector in P.

WARNING

Press down the parking brake pedal firmly to its full extent.

Parking on a hill

If the vehicle is pointing uphill, turn the front wheels so that they point away from the curb. If the vehicle is pointing downhill, turn the front wheels so that they point toward the curb.

Releasing the parking brake 1. Press firmly on the brake pedal.

1. Pull handle

116 03 Your driving environment

Parking brake

Electric parking brake (option1)

An electric parking brake has the same function as a manual parking brake.

NOTE

 A faint sound from the parking brake's electric motor can be heard when the parking brake is being applied. This

sound can also be heard during the automatic function check of the parking brake.

The brake pedal will move slightly when the electric parking brake is applied or released.

Low battery voltage If the battery voltage is too low, the parking brake cannot be applied or released. Connect an auxiliary battery if the battery voltage is too low, see page 109.

1The electric parking brake is available as an option on certain models.

Applying the electric parking brake

1. Press firmly on the brake pedal.

2. Press the control.

3. Release the brake pedal and ensure that the vehicle is at a standstill.

4. When the vehicle is parked, the gear selector must be in position P.

symbol in the instrument panel flashes while the parking bake is being applied, and glows steadily when

The the parking brake has been fully applied.

NOTE

In an emergency the parking brake can be applied when the vehicle is moving by holding in the control. Braking

will be interrupted when the accelerator pedal is depressed or the control is released.

An audible signal will sound during this procedure if the vehicle is moving at speeds above 6 mph (10 km/h).

Parking on a hill

If the vehicle is pointing uphill, turn the front wheels so that they point away from the curb. If the vehicle is pointing downhill, turn the front wheels so that they point toward the curb.

117 03 Your driving environment

Parking brake

Releasing the electric parking brake

Manual release 1. Fasten the seat belt.

2. Insert the remote key in the ignition slot.

3. Press firmly on the brake pedal.

4. Pull the parking brake control.

Vehicles with Keyless drive (option) 1. Press the START/STOP ENGINE button.

2. Press firmly on the brake pedal.

3. Pull the parking brake control.

Automatic release 1. Start the engine.

2. Fasten the seat belt.

NOTE

For safety reasons, the parking brake is only released automatically if the engine is running and the driver is

The electric parking brake will be released immediately when the accelerator pedal is pressed and the gear selector

wearing a seat belt.

is in position D or P.

3. Move the gear selector to position D or R and press the accelerator pedal. The parking brake will release when the vehicle begins to move.

Heavy load uphill A heavy load, such as a trailer, can cause the vehicle to roll backward when the parking brake is released automatically on a steep incline. To help avoid this:

1. Keep the electric parking brake lever pushed in with the left hand while shifting into Drive with the right.

2. While pressing the throttle pedal to pull away, release the parking brake lever only after the vehicle begins to move.

Symbols

Messages

Parking brake not fully released - A fault is preventing the parking brake from being released. Contact an authorized Volvo workshop.

118 03 Your driving environment

Parking brake

If you drive off with this error message showing, a warning signal sounds.

Parking brake not applied - A fault is preventing the parking brake from being applied. Try to apply and release. Contact a Volvo workshop if the message remains.

Parking brake Service required - A fault has arisen. Contact a Volvo workshop if the fault remains.

WARNING

If the vehicle must be parked before the fault has been corrected, always put the gear selector in P and turn the wheels so that they point away from the curb if the vehicle is pointing uphill or toward the curb if it is pointing downhill.

119 03 Your driving environment

This page left intentionally blank.

Contents | Top of Page

2 0 0 8
VOLVO

S80

120 04 Comfort and driving pleasure 122
Menus and messages 126
Climate system 134
Audio system 147
Trip computer 149
Compass 151
Stability system 153
Active chassis system-Four C 154
Cruise control 156
Adaptive Cruise Control-ACC Distance Alert 163
Collision Warning with Auto-brake (option) 166
171
Driver Alert System-option 176
Park assist (option) Blind Spot Information System (option) 179
183
Passenger compartment convenience

121 04 Comfort and driving pleasure

122 04 Comfort and driving pleasure

Menus and messages

Center console

Certain functions are controlled from the center console via the menu system or from the optional keypad in the steering wheel. Each function is described under its respective section.

The current menu level is shown at the top right of display in the center console.

Center console controls

Navigation button - scrolls and selects among menu options

ENTER - selects menu options

MENU - accesses the menu system

EXIT - leads back one step in the menu structure. A long press exits the menu system.

Steering wheel keypad

ENTER

EXIT

Navigation buttons.

If the steering wheel keypad has ENTER and EXIT, the buttons center console.

to

have the same function as those in the

Search paths Access to some functions is provided directly via the function buttons and others are access through the menu system.

Search paths to the menu system functions are listed as follows: Car settings have been taken first:

Lock settings, if the following steps

1. Press MENU.

2. Scroll to Menu and press ENTER.

3. Scroll to Submenu and press ENTER.

The navigation button can be used instead of ENTER and EXIT when navigating the menu hierarchy. The right arrow is equal to ENTER and the left arrow to EXIT.

The menu options are numbered and can also be selected directly with the numerical keypad (1-9 only).

123 04 Comfort and driving pleasure

Menus and messages

Menu overview

Car key memory

Seat & mirror positions

Car settings

Fold mirr. when locking (option on certain markets only)

Collision warning settings (option)

Light settings

Lock settings

Parking camera settings (accessory)

Steering force level (option)

Information

Climate settings

Automatic blower adjust

Recirculation timer

Auto. rear defroster

Reset climate settings

Main menu AM

Audio settings1

Sound stage

Equalizer, front

Equalizer, rear

Auto. volume control

Resets all audio settings.

Main menu FM

FM settings

Radio text

Advanced radio settings

Audio settings

Main menu CD

Random

Off

Folder

Disc

Single disc

All discs

CD settings

Disc text (option)

Audio settings

Main menu AUX

Volume, AUX input

Audio settings

1The menu option for audio settings is available in all audio sources.

124 04 Comfort and driving pleasure

Menus and messages

Main instrument panel

READ - access to the list of messages and message confirmation.

Thumbwheel - browse among menus and options in the list of functions.

RESET - reset the active function. Used in certain cases to select/activate a function, see the explanation under each

respective function.

The menus shown on the information displays in the instrument panel are controlled with the left lever. The menus shown depend on ignition mode. Press READ to erase a message and return to the menus.

Menu overview Driving distance on current fuel reserve

Average

Instantaneous:

Average speed

Current speed in mph (Canadian models only)

DSTC

Message

When a warning, information or indicator symbol comes on, a corresponding message appears on the information display. An error message is stored in a memory list until the fault is rectified.

Press READ to acknowledge and scroll among the messages.

NOTE

If a warning message appears while you are using the trip computer, the message must be read and confirmed by pressing READ before the previous activity can be resumed.

125 04 Comfort and driving pleasure

Menus and messages

126 04 Comfort and driving pleasure

Climate system

Introduction

Air conditioning The vehicle is equipped with Electronic Climate Control (ECC). The climate control system cools, heats or dehumidifies the air in the passenger compartment.

NOTE

The air conditioning can be switched off, but to ensure the best possible climate comfort in the passenger

compartment and to prevent the windows from misting, it should always be on.

In warm weather, a small amount of water may accumulate under the car when it has been parked. This water is

condensation from the A/C system and is normal.

Sensor location

The sunlight sensor is located on the top side of the dashboard.

NOTE

The sunlight sensor monitors which side of the car that is most exposed to sunlight. This can mean that the temperature may differ between the right and left-side air vents, even if the temperatures set for both sides of the passenger compartment are the same.

 The temperature sensor for the passenger compartment is located below the climate control panel. The outside temperature sensor is located on the door mirror. The humidity sensor (option) is located in the interior rearview mirror.

NOTE

Do not cover or block the sensors with clothing or other objects.

Side windows and moonroof To ensure that the air conditioning works optimally, the side windows, and the optional moonroof should be closed.

Fog on the inside of the windows The defroster function should be used to remove fog or mist from the inside of the windows. Keeping the windows clean with a commercially available window washing spray will also help prevent fogging or misting.

Vents in the parcel shelf

NOTE

The air vents at the rear of the parcel shelf should never be obstructed.

Temporary shut-off of the air conditioning The air conditioning is momentarily disengaged during full-throttle acceleration or when driving uphill with a trailer. This may result in a temporary increase in cabin temperature.

Ice and snow Always keep the air intake grille at the base of the windshield free of snow.

Climate system maintenance Special tools and equipment are required to maintain and carry out repairs on the climate system. Work of this type should only be done by a trained and qualified Volvo service technician.

Refrigerant Volvo cares about the environment. The air conditioning system in your car contains a CFC-free refrigerant - R134a. This substance

127 04 Comfort and driving pleasure

Climate system

will not deplete the ozone layer. The air conditioning system contains 1.8 lbs (800 g) of R134a. The systems uses PAG oil.

Passenger compartment filter Replace the cabin air filter with a new one at the recommended intervals. Please refer to your Warranty and Service Records Information booklet, or consult a trained and qualified Volvo service technician for these intervals. The filter should be replaced more often when driving under dirty and dusty conditions. The filter cannot be cleaned and therefore should always be replaced with a new one.

NOTE

There are different types of cabin air filters. Ensure that the correct type is installed.

Interior Air Quality System (IAQS) A multifilter helps reduce gases and particles in the incoming air, thereby reducing the levels of odors and contaminants entering the vehicle. The air quality sensor detects increased levels of contaminants in the outside air. When the air quality sensor detects contaminated outside air, the air intake closes and the air inside the passenger compartment is recirculated, i.e. no outside air enters the vehicle. The filter also cleans recirculated passenger compartment air.

NOTE

Contact your Volvo retailer for IAQS air filter replacement intervals.

Menu settings The default settings for three of the climate system's functions can be changed in the menu system, see page 123:

Blower speed in automatic mode, see page 130. Recirculation timer for passenger compartment air, see page 130. Automatic rear window defrosting, see page 100.

The functions can also be returned to factory settings in the menu system.

128 04 Comfort and driving pleasure

Climate system

Air distribution

The incoming air is distributed from 20 different vents in the passenger compartment.

Air distribution is fully automatic in AUTO mode.

If desired, air distribution can be controlled manually, see page 133.

Air vents in the dashboard

Open

Closed

Horizontal airflow

Vertical airflow

Direct the outer air vents toward the side windows to defrost.

Air vents in the door pillars

Open

Closed

Horizontal airflow

Vertical airflow

Direct the outer air vents toward the side windows to defrost.

Direct the vents into the passenger compartment to maintain a comfortable climate in the rear seat.

129 04 Comfort and driving pleasure

Climate system

Electronic climate control, ECC

Ventilated front driver's seat (option)

Blower

Heated front driver's seat (option)

Air distribution

Heated front passenger's seat (option)

Auto

Ventilated front passenger's seat (option)

Temperature control, passenger's side

A/C - On/Off

Heated rear window and door mirrors, see page 100.

Defroster (maximum effect)

Recirculation/Air quality system

Temperature control, driver's side

Ventilated front seats (option) The ventilation system consists of fans in the seats and backrests that draw air through the seat upholstery. The cooling effect increases as the air in the passenger compartment becomes cooler.

The ventilation is controlled by the ECC system, which takes into account the seat temperature, sunlight in the passenger compartment, and the ambient temperature.

The ventilation can be used at the same time as seat heating.

The ventilation system can be activated when the engine is running. There are three comfort levels that produce different cooling and dehumidification effects:

Level three: press the button once for maximum output - three indicator lights come on. Level two: press the button twice for a lower output - two indicator lights come on. Level one: press the button three times for the lowest output - one indicator light comes on. Press the button a fourth time to switch off the function - the indicator light will go out.

Blower control

Turn the control clockwise to increase or counterclockwise to decrease the blower speed. Pressing the AUTO switch will automatically regulate blower speed and override manual adjustment.

NOTE

If the blower is turned off completely, the air conditioning is disengaged, which may result in fogging on the windows.

Heated front seats (option)

Press the button once for the highest heat level - three indicator lights come on. Press the button twice for a lower heat level - two indicator lights come on. Press the button three times for the lowest heat level - one indicator light comes on. Press the button four times to switch off the heat - no indicator lights come on.

130 04 Comfort and driving pleasure

Climate system

Heated rear seats (option)

Heat control for the outboard seating positions takes place in the same way as for the front seat.

Air distribution

The figure consists of three buttons. When the buttons are pressed, an indicator light in front of the respective part of the figure illuminates and shows which air distribution is selected, see page 133.

Auto

The function automatically regulates cooling, heating, blower speed, recirculation, and air distribution to maintain the chosen temperature. If you select one or more manual functions, the other functions continue to be controlled automatically. The air quality sensor is engaged and all manual settings are switched off when AUTO is pressed. The display shows AUTO CLIMATE.

Blower speed in automatic mode can be set under Climate settings Normal or High.

Automatic blower adjust. Choose between Low,

NOTE

Selecting the lowest blower speed may increases the risk of fog forming on the windows.

For a description of the menu system, see page 123.

Temperature control

The temperatures on the driver and passenger sides can be set independently. When the vehicle is started, the most recent setting is resumed.

NOTE

Heating or cooling cannot be speeded up by selecting a higher/lower temperature than the actual temperature required.

A/C - ON/OFF

The air conditioning is controlled automatically by the system when the ON light is on. This cools/heats and dehumidifies the incoming air. When the OFF light is on, the air conditioning is always disengaged. Other functions are still controlled automatically. When defroster is selected, the air conditioning system is set for maximum blower speed and dehumidification.

131 04 Comfort and driving pleasure

Climate system

Defroster

This function defrosts/deices the windshield and front side windows. The indicator light in the defroster button lights when the function is active.

Blower speed increases automatically and the air conditioning will switch on (if not already on and if the passenger

compartment blower is not turned off) to dehumidify the air in the passenger compartment. Air conditioning can be switched off by pressing the AC button.

Recirculation will not function while defrost is engaged.

The climate system will return to its previous settings when the defroster function is switched off.

Recirculation/air quality system

Recirculation

This function can be used to shut out exhaust fumes, smoke, etc from the passenger compartment. The air in the passenger compartment is then recirculated, i.e., no air from outside the car is taken into the car when this function is activated. The indicator light in the button will illuminate when recirculation is selected.

If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows, especially in winter.

Timer The timer function minimizes the risk of fogging, or stale air when the recirculation function is selected by automatically switching off the function after a certain length of time, depending on the ambient temperature. Activate/deactivate the function under Climate control settings For a description of the menu system, see page 123.

Recirculation timer.

NOTE

When Defroster is selected, recirculation is always deactivated.

Interior Air Quality System-IAQS (option)

This system consists of a multifilter and an air quality sensor. The filter helps remove gases and particles from the incoming air, thereby reducing the amounts of odors and contaminants entering the vehicle. The air quality sensor detects increased levels of contaminants in the outside air. When the air quality sensor detects contaminated outside air, the air intake closes and the air inside the passenger compartment is recirculated, i.e., no outside air enters the vehicle. The filter also cleans recirculated passenger compartment air. When the AUTO button is depressed the air quality sensor is always engaged.

Activating the air quality sensor

Switch between the three functions by pressing the button repeatedly.

The left orange light comes on - the air quality sensor is disengaged. The center green light comes on - recirculation not engaged, providing it is not required for cooling in hot weather. The right orange light comes on - recirculation is engaged.

132 04 Comfort and driving pleasure

Climate system

NOTE

The air quality sensor should always be engaged in order to obtain the best air in the passenger compartment. Recirculation is limited in cold weather to avoid fogging. If the insides of the windows start fogging, disengage the air quality sensor. Use the defroster function to increase

airflow to the front, side, and rear windows.

133 04 Comfort and driving pleasure

Climate system

Air distribution table

134 04 Comfort and driving pleasure

Audio system

Introduction

The audio system is available in two versions: High Performance and Premium Sound. The system version is shown in the display when the audio system is switched on.

If the audio system is on when the ignition is switched off, it will come on automatically the next time the ignition is put in mode I or higher. The audio system can be operated without a key in the ignition slot for 15 minutes at a time by pressing the POWER button (the driver's door must be closed on vehicles with the optional keyless drive).

Some functions are controlled from the menu system in the center console. For more information on menus, see page 123.

are trademarks of Dolby Laboratories Licensing Corporation. The Dolby Surround Pro Logic II and the symbol Dolby Surround Pro Logic II System is manufactured under license from Dolby Laboratories Licensing Corporation.

Overview