Download PDF Manual

ported by the jack. Otherwise, personal injury may occur.


D Do not start or run the engine while your vehicle is supported by the jack.


D Stop the vehicle on a level firm ground, firmly set the parking brake and put the transmission in “P” (automatic) or reverse (manual). Block the wheel diag- onally opposite to the one be- ing changed if necessary.


D Make sure to set the jack prop- erly in the jack point. Raising the vehicle with jack improper- ly positioned will damage the vehicle or may allow the ve- hicle to fall off the jack and cause personal injury.


D Never get under the vehicle when the vehicle is supported by the jack alone.


D Use the jack only for lifting your vehicle during wheel changing.


D Do not raise the vehicle with


someone in the vehicle.


D When raising the vehicle, do not put an object on or under the jack.


D Raise the vehicle only high enough to remove and change the tire.


228


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


NOTICE


Do not continue driving with a deflated tire. Driving even a short distance can damage a tire and wheel beyond repair.


SZ41023


The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) de- pending on road conditions and your driving habits. When tread wear indi- cators appear on the tire, replace the tire. See also the tire information in Sec- tion 7−2 for details on the tread wear indicators and other service informa- tion.


Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by the distinctive wording “TEM- PORARY USE ONLY” molded into the sidewall of the tire. The compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installa- tion in case of a flat tire.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


229


05 11.10


CAUTION


NOTICE


is re- Your ground clearance duced when the compact spare tire is installed so avoid driving over obstacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not at- tempt to go through an auto- matic car wash as the vehicle may get caught, resulting in damage.


D The compact spare tire was de- signed especially for your To- yota. Do not use it on any other vehicle.


D Do not use more than one com- pact spare tire at the same time.


D The pressure for the compact spare tire must be 420 kpa (4.2
kgf/cm2 or bar, 60 psi).


D Do not exceed 80 km/h (50
mph) when driving with the compact spare tire.


D Replace the compact spare tire with the standard tire as soon as possible.


D Avoid sudden acceleration, sudden deceleration and sharp turns with the compact spare tire.


—Required tools and spare tire


PS41533


1. Get the required


spare tire.


tools and


1. Tie−down belt 2. Tool bag 3. Jack handle 4. Spare tire 5. Jack


Split seat only—Before removing the deck board, slide the rear seat fully forward. To remove the deck board, see “Luggage storage box” on page 175
in Section 1−10. You will find a wheel nut wrench in the tool bag.


230


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.


PS41503


SM41002


To remove the jack, move the driver seat to the front−most position and re- move the cover. To remove: Turn the joint in direction 1 by hand until the jack is free. To store: Turn the joint in direction 2
by hand until the jack is firmly secured to prevent it flying forward during a collision or sudden braking.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


231


05 11.10


—Blocking the wheel


—Removing wheel ornament (on some models)


PS41532


PS41505


PS41506


To remove the spare tire, loosen the bolt and remove it. Then take the spare tire out of the vehicle. When storing the spare tire, put it in place with the inner side of the wheel facing up. Then secure the tire by re- peating the above removal steps in reverse order to prevent it from flying forward during a collision or sudden braking. The compact tire storage area is de- signed only for a compact spare tire. Standard size tire cannot be stored in this storage area.


232


2. Block the wheel diagonally op- posite the flat tire to keep the vehicle from rolling when it is jacked up.


When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.


Steel wheels (type A)


PS41507


Steel wheels (type B)


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


3. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.


CAUTION


Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury.


—Loosening wheel nuts


PS41508


CAUTION


Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, which could cause a serious ac- cident.


4. Loosen all the wheel nuts. Always loosen the wheel nuts before raising the vehicle. The nuts turn counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the han- dle is on the right side, as shown above. Grasp the wrench near the end of the handle and pull up on the handle. Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just un- screw them about one−half turn.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


233


05 11.10


—Positioning the jack


—Raising your vehicle


PS41509


PS41510


CAUTION


Never get under the vehicle when the vehicle is supported by the jack alone.


5. Position the jack at the correct


jack point as shown.


Make sure the jack is positioned on a level and solid place.


6. After making sure that no one is in the vehicle, raise it high enough so that the spare tire can be installed.


Remember you will need more ground clearance when putting on the spare tire than when removing the flat tire. To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double−check that it is properly posi- tioned.


234


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


—Changing wheels


—Reinstalling wheel nuts


NS41511


NS41512


PS41534


7. Remove the wheel nuts and


change tires.


Lift the flat tire straight off and put it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.


Before putting on wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal−to−met- al contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.


8. Reinstall all the wheel nuts fin-


ger tight.


Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire and see if you can tighten them more.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


235


05 11.10


—Lowering your vehicle


PS41514


CAUTION


Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loosen and the wheels may fall off, which could cause a seri- ous accident. If there is oil or grease on any bolt or nut, clean it.


9. Lower the vehicle completely


and tighten the wheel nuts.


Turn the jack handle counterclock- wise to lower the vehicle. Use only the wheel nut wrench to tighten the nuts. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the wrench is securely engaged over the nut. Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.


CAUTION


D When


lowering the vehicle, make sure all portions of your body and all other persons around will not be injured as the vehicle is lowered to the ground.


D Have the wheel nuts tightened with torque wrench to 103 N·m (10.5 kgf·m, 76 ft·lbf), as soon as possible after changing wheels. Otherwise, the nuts may loosen and the wheels may fall off, which could cause a serious accident.


D Do not attach a heavily dam- aged plastic wheel ornament. It may fly off the wheel and cause accidents while the ve- hicle is moving.


236


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


—Stowing flat tire 10.Restow all the tools and jack se- curely. Then secure the flat tire with the tire tie−down belt in the luggage compartment as fol- lows.


Before stowing flat tire, remove the luggage cover. (See “Luggage cover” on page 175 in Section 1−10.)


CAUTION


Before driving, make sure all the tools, jack and flat tire are se- curely in place in their storage location to reduce the possibility of personal injury during a colli- sion or sudden braking.


PS41515


PS41516


1. Aluminum wheels—Before stow- ing the flat tire, remove the center wheel ornament by pushing from the reverse side. Be careful not to lose the wheel ornament.


2. Hook each belt end to the corre- sponding anchor brackets. Then, put the center portion of the belt onto the rear center head re- straint.


3. Return the deck board to the origi- nal position and then lock it. (See “Luggage storage box” on page 175 in Section 1−10.)


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


237


05 11.10


PS41517


PS41518


PS41519


4. Lay the flat tire on the luggage floor so that the outer side of the tire wheel faces toward the rear of the vehicle. Detach the rear center head restraint from the seat and release the belt.


5. Pass the belt through the center


hole of the flat tire wheel.


6. Put the center portion of the belt onto the rear center head restraint position and then return the rear center head restraint.


238


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


PS41520


7. Hold the buckle and pull the belt


to secure the tire.


After stowing the flat tire, check that the tire and belt are secured.


—After changing wheels 11. Check the air pressure of the re-


placed tire.


Adjust the air pressure to the specifi- cation designated on page 299 in Section 8. If the pressure is lower, drive slowly to the nearest service station and fill to the correct pressure. Do not forget to reinstall the tire infla- tion valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible. As soon after changing wheels as possible, tighten the wheel nuts to the torque specified on page 299 in Sec- tion 8 with a torque wrench. And have a technician repair the flat tire.


CAUTION


Before driving, make sure all the tools, jack and flat tire are se- curely in place in their storage location to reduce the possibility of personal injury during a colli- sion or sudden braking.


PS41531


Position the tools as shown in the il- lustration. Fold the tool bag over and then restow it.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


239


05 11.10


If your vehicle becomes stuck If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward.


CAUTION


Do not attempt to rock the vehicle free by moving it forward and back- ward if people or objects are any where near the vehicle. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or ob- jects.


If your vehicle needs to be towed—


NOTICE


(a) Towing with wheel lift type truck—


to


the


If you rock your vehicle, observe the following precautions to prevent dam- age transmission and other parts. z Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.


z Do not race the engine and avoid


spinning the wheels.


z If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.


—From front


—From rear


PS41522


(b) Using flat bed truck


240


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Only when you cannot receive a towing service from a Toyota dealer or com- mercial tow truck service, tow your ve- hicle carefully in accordance with the instructions given in “—Emergency towing” in this Section. Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following few precautions are observed. If necessary, show this page to the tow truck driver. TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly.


the state/provincial and


if


it


(a) Towing with wheel lift type truck From front—Release the parking brake.


NOTICE


When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.


D Automatic transmission:


Use a wheels.


towing dolly under


the


front


NOTICE


Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage the transmission.


to


(b) Using flat bed truck


From rear— D Manual transmission:


We recommend using a towing dolly under the front wheels. If you do not use a towing dolly, place the ignition key in the “ACC” position and put the transmission in neutral.


NOTICE


Do not tow with the key removed or in the “LOCK” position when towing from the rear without a towing dolly. The steering lock mechanism is not strong enough front wheels straight.


to hold


the


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


241


05 11.10


(c) Towing with sliding type


truck


—Emergency towing


PS41523


PS41524


(c) Towing with sling type truck


Front


NOTICE


Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.


PS41525


Rear


If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. If a towing service is not available in an emergency, your vehicle may be temporarily towed by a cable or chain secured to either the emergency towing eyelet on the front of the vehicle or to the right emergency towing eyelet un- der the rear of the vehicle. Use extreme caution when towing vehicles. Vehicles with an automatic transmis- sion, use only the front towing eyelet when towing your vehicle. To towing eyelet, see “—Installing front towing eyelet” on page 243 in this Section.


install


front


the


NOTICE


z Only use specified towing eyelet; otherwise your vehicle may be dam- aged.


z Vehicles with an automatic trans- mission, never tow a vehicle from the rear with four wheels on the ground. This may cause serious damage to the transmission.


242


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard−surfaced roads for a short dis- tance and at the wheels, axles, drive train, steering and brakes must all be in good condition.


low speeds. Also,


CAUTION


Use extreme caution when towing ve- hicles. Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelets and towing cable or chain. The eyelets and towing cable or chain may break and cause serious injury or damage.


NOTICE


z Use only a cable or chain specifi- cally intended for use in towing ve- hicles. Securely fasten the cable or chain to the towing eyelet provided. z Do not use the left rear eyelet. It is


not designed for towing.


Before towing, release the parking brake and put the transmission in neutral (manu- al) or “N” (automatic). The key must be in “ACC” (engine off) or “ON” (engine run- ning).


CAUTION


If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.


—Installing front towing eyelet


PS41526


1. Remove the front towing eyelet cover on the front bumper, using a flathead screwdriver which is wrapped with a cloth.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


243


05 11.10


If you cannot shift automatic transmission selector lever


PS41527


PS41528


PS41529


2. Use the towing eyelet in the tool bag. Secure the front towing eyelet to the hole on the front bumper by turning clockwise. (For tool bag storage location, see tools and spare tire” on page 230.)


“—Required


the


3. Tighten the front towing eyelet securely


by a wheel nut wrench.


CAUTION


When installing the eyelet on the ve- hicle, be sure to tighten the front eyelet securely. If the eyelet is loose, it may come off when being towed and result in death or serious injury.


though


If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn


the brake pedal


ignition key


the


to “LOCK” the parking


position. Make sure brake is applied.


2. Pry up the cover with a flathead


screwdriver or equivalent.


244


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


PS41530


3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.


4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,


keep the brake pedal depressed.


Be sure to have the system checked by your Toyota dealer as soon as possible.


If you lose your keys You can purchase a new key at your Toyota dealer if you can give them the key number. If your vehicle is equipped with the engine immobilizer system, the dealer will also need your master key. Vehicles with engine immobilizer sys- tem—Even if you lose only one key, con- tact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobilizer system must be replaced. See page 10 in Section 1−2. You can use the wireless remote control system with the new key. Contact your Toyota dealer for detailed information. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, using If you must break a window in, we suggest the smallest side window be- breaking cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.


the suggestion given in “Keys” on


their special


to get


tools.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


245


05 11.10


246


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


SECTION 5


CORROSION PREVENTION AND APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion Washing and waxing your Toyota Cleaning the interior


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


248
249
251


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


247


05 11.10


Protecting your Toyota from corrosion Toyota, through its diligent research, de- sign and use of the most advanced technology available, helps prevent corro- sion and provides you with the finest qual- ity vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long−term corrosion prevention. The most common causes of corrosion to your vehicle are: D The accumulation of road salt, dirt and moisture in hard−to−reach areas under the vehicle.


D Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.


Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: D Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea− coast or in areas of industrial pollution. D High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.


D Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.


D High ambient temperatures can cause corrosion to those components of the vehicle which do not dry quickly due to lack of proper ventilation.


The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: D If you drive on salted roads


the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.


in


D High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.


D Wash the underside of the vehicle thor-


oughly when winter is over.


See “Washing and waxing your Toyota” for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.


248


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full−size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp as to cause corrosion. Even if your garage is heated, a wet vehicle can cor- rode if the ventilation is poor.


Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. D When driving in a coastal area D When driving on a road sprinkled with


antifreeze


D When exposed to coal tar, tree sap, bird droppings and carcass of an insect D When driving in areas where there is a lot of smoke, soot, dust, iron dust or chemical substances


D When the vehicle becomes remarkably


dirty with dust and mud Hand−washing your Toyota Work in the shade and wait until the vehicle body is not warm to the touch.


CAUTION


D When cleaning under floor or chas- sis, be careful not to injure your hands.


D Exhaust gases cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot ex- haust pipe can cause burns.


NOTICE


When the front wiper arms need to be lifted away from the windshield to wash the vehicle, raise the arm on the driver side first. Conversely, when returning the wipers to their original positions, fold down the arm on the front passenger side first. Failure to perform the operations in the correct order results in damage.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


249


05 11.10


1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the vehicle or the wheel wells.


2. Wash with a mild car−wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.


Fuel filler door: Do not apply water (high− pressure car wash, for example) at or near the fuel tank inlet with the fuel filler door opened. If the water enters the air vent, you may experience trouble with re- fueling or rough engine idling. Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stance splash an ornament, be sure to wash them off with water and check if the ornament is damaged. Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft.


Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.


NOTICE


To prevent damage to the antenna, make sure to remove it before driving your Toyota through an automatic car wash.


tar: Remove with


Exterior lights: Wash carefully. Do not use organic substances or scrub them with a hard brush. This may damage the sur- faces of the lights. Road turpentine or cleaners that are marked safe for painted surfaces. 3. Rinse


can cause streaking. In hot weather you may need to rinse each section right after you wash it.


thoroughly—dried


soap


4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.


NOTICE


z Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may be tox- ic or cause damage.


z Do not scrub any part of the ve- hicle with a hard brush, which may cause damage.


250


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Apply wax once a month or if the vehicle surface does not repel water well. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.


2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. Windshield washer nozzles: Make sure that the nozzles do not become blocked If a nozzle becomes when waxing. blocked, contact your Toyota dealer to have the vehicle serviced.


NOTICE


If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.


Exterior lights: Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. If you accidentally put wax on the light surfaces, wipe or wash it off. 3. Wax


the vehicle again when water does not bead but remains on the sur- face in large patches.


NOTICE


Always remove the plastic bumpers if your vehicle is re−painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers.


Cleaning the interior


CAUTION


D Vehicles with side airbags and cur-


tain shield airbags: Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags and curtain shield airbags from activating cor- rectly, resulting in serious injury.


D Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


251


05 11.10


Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.


NOTICE


Do not use solvent, thinner, gasoline or window cleaner on the interior.


to


foam−type shampoo


Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.


Windows The windows may be cleaned with any household window cleaner.


NOTICE


When cleaning the inside of the win- dows, be careful not to scratch or damage the heater wires or connec- tors.


Air conditioning control panel, car au- dio, instrument panel, console panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.


NOTICE


z Do not use dye or bleach on the


belts—it may weaken them.


z Do not use the belts until they be-


come dry.


252


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


NOTICE


z Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.


z If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.


z If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- tain ingredients mentioned above. Immediately clean any spill using the method mentioned above.


the


Leather Interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the leather gets wet, dry with a soft clean cloth. Allow the leather to dry in a venti- lated shaded area.


NOTICE


z If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.


z Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for clean- ing these could cause discoloring.


leather as


the


z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.


z Mildew may develop on soiled leath- er upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.


to direct sunlight z Long exposure may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer.


z The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.


z Improper cleaning of the leather up- in discolor-


holstery could result ation or staining.


If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


253


05 11.10


254


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


SECTION 6


VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements General maintenance Does your vehicle need repairing? Emissions Inspection and Maintenance (I/M) programs


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


256
257
259
260


For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


255


05 11.10


Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day−to−day care, is more important than ever before to ensure smooth, trouble−free, safe, and economical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.


256


Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may have maintenance, replacement, or repair of the control devices and system performed by any automotive repair individual without invalidating this warranty. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for complete warranty information.


establishment


emission


elect


also


for


or


to


Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented in Section 7.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


you are


If skilled do−it−yourself mechanic, the Toyota service manuals are recommended. Please be aware that do−it−yourself maintenance can affect your warranty coverage. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for the details.


the


items


listed,


General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.


CAUTION


Make these checks only with ade- quate ventilation if you run the en- gine.


IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See Section 7−3 for additional in- formation.


Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see− through reservoir when the engine is cold. See Section 7−2 for additional information. Radiator, condenser and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt or insects. See Section 7−2
for additional information. Battery condition Check the battery condition by the indica- tor color. See page 284 in Section 7−3 for additional information. Brake fluid level Make sure the brake fluid level is correct. See Section 7−2 for additional information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level ground. See Section 7−2 for additional information. Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” on page 181 in Section 2.)


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


257


05 11.10


INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise. Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraint move up and down smooth- ly and that the locks hold securely in any latched position. For rear seatbacks, check that the latches lock se- curely.


folding−down


Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure the belt webbing is not cut, frayed, worn or dam- aged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes In a safe place, check that the brakes do not pull to one side when applied. Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied.


to


time


Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately. Doors and engine hood Check that all doors and back door oper- ate smoothly and all latches lock securely. Make sure the engine hood secondary latch secures the hood from opening when the primary latch is released.


fluid after


258


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


Tire inflation pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See Section 7−2 for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See Sec- tion 7−2 for additional information. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tries according to the maintenance (For scheduled maintenance information, please “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) See Section 7−2 for additional information.


schedule.


refer


the


to


tip−offs


for changes


Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: D Engine missing, stumbling, or pinging D Appreciable loss of power D Strange engine noises D A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)


If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.


CAUTION


Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.


D Change


in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)


D Flat−looking tire; excessive tire squeal


when cornering; uneven tire wear


D Vehicle pulls to one side when driving


straight on a level road


D Strange noises related to suspension


movement


D Loss of brake effectiveness; spongy feeling brake or clutch pedal; pedal al- most touches floor; vehicle pulls to one side when braking


D Engine coolant temperature continually


higher than normal


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


259


The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re−testing.


05 11.10


and


indicator


the malfunction


Inspection


in- include OBD


Emissions Maintenance (I/M) programs Some states have vehicle emission spection programs which (On−Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the battery is disconnected or run down, the codes are erased. Also, depending on your driving habits, the codes may not be completely set. Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test.


the malfunction


indicator


test as


I/M


the


if


260


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


SECTION 7− 1


DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do−it−yourself service precautions Parts and tools Positioning the jack


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


262
263
264
266
267


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


261


05 11.10


Engine compartment overview


1. Windshield washer and rear window


washer fluid tank


2. Engine oil filler cap


3. Fusible link block


4. Brake fluid reservoir


5. Fuse block


6. Battery


7. Radiator


8. Condenser


9. Electric cooling fan


10. Engine coolant reservoir


11. Engine oil level dipstick


PS71507a


262


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


Fuse locations


PS71508


PS71505


PS71502


Spare fuses


PS71504


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


263


05 11.10


Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools”. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:


instructions only


CAUTION


D When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)


(Removing


belts.


D Right after driving,


the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.


D If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.


D Do not


leave anything


that may burn easily, such as paper or rags, in the engine compartment.


D Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. D Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.


D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.


D Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.


D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.


D Do not


leave used oil within the


reach of children.


264


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.


for


fluid


D Take care when filling the brake and clutch reservoirs because brake fluid can harm your eyes and damage painted surfaces. fluid gets in your eyes, flush your eyes with clean water immediately. If you still feel uncomfortable with your eyes, go to the doctor.


If


NOTICE


z Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.


z Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).


z If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.


z Do not allow dirt or anything else to fall through the spark plugholes. z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.


z Do not reuse iridium−tipped spark


plugs by cleaning or regapping.


z Do not overfill automatic transmis- transmission


fluid, or


the


sion could be damaged.


z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.


z Be careful not to scratch the glass


surface with the wiper frame.


z When closing


the engine hood, check to see that you have not for- gotten any tools, rags, etc.


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


265


05 11.10


Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): D “Toyota Genuine Motor Oil” or equiva-


lent See page 270 in Section 7−2 for de- tails about engine oil selection.


Tools: D Rag or paper towel D Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): D “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).


Tools: D Funnel (only for adding coolant)


266


REPLACING LIGHT BULBS Parts: D Bulb with same number and wattage rating as original in “Replacing light bulbs” on page 288 in Section 7−3.)


charts


(See


D Flathead screw driver


CHECKING BRAKE FLUID Parts (if level is low): D SAE J1703 or FMVSS No.116 DOT 3


brake fluid


Tools: D Rag or paper towel D Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: D Warm water D Baking soda D Grease D Conventional wrench


(for


terminal


clamp bolts)


CHECKING AND REPLACING FUSES Parts (if replacement is necessary): D Fuse with same amperage rating as


original


ADDING WASHER FLUID Parts: D Water D Washer fluid containing antifreeze


(for winter use)


Tools: D Funnel


2006 YARIS HATCHBACK from Aug. ’05 Prod. (OM52703U)


05 11.10


Positioning the jack


Do not jack up


PS71506


Front of vehicle


Lower back outer panel (protrusion)


When jacking up your vehicle with the jack, position jack correctly as shown in the illustration. Jack position . . . . . . . . . . . . . . . . . . . .


the


Loading...
x