2011 Toyota Yaris Hatchback Owners Manual

after blinking for 1 minute to indicate a system malfunction.

n Tire life

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

270

4-3. Do-it-yourself maintenance

n If the tread wears down below 0.16 in. (4 mm) on snow tires

The effectiveness of snow tires is lost.

n Maximum load of tire

Check that the maximum load of the replacement tire is greater than 1/2
of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater.

For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire. (→P. 370).

n Tire types

1 Summer tires

Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.

2 All season tires

All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions, as well as for use year round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.

3 Snow tires

For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restriction. Snow tires should be installed on all wheels. (→P. 169)

271

4-3. Do-it-yourself maintenance

n Routine tire inflation pressure checks

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

n Tire pressure warning system certification

MODEL/FCC IDs: Transmitter: PAXPMV107J Receiver: HYQ13BCX

For vehicles sold in U.S.A.

NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user's authority to operate the equip- ment.

272

4-3. Do-it-yourself maintenance

CAUTION

n Tire pressure warning system operation

The tire pressure warning system may not provide warning immediately if a tire bursts or if sudden air leakage occurs.

n When inspecting or replacing tires

Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous han- dling characteristics, which may lead to an accident resulting in death or serious injury. l Do not mix tires of different makes, models or tread patterns. Also, do

not mix tires of remarkably different treadwear.

l Do not use tire sizes other than those recommended by Toyota. l Do not mix differently constructed tires (radial, bias-belted or bias-ply

tires).

l Do not mix summer, all season and winter tires. l Do not use tires that have been used on another vehicle. l Do not use tires if you do not know how they were used previously.

273

4-3. Do-it-yourself maintenance

NOTICE

n Repairing or replacing tires, wheels, tire pressure warning valves,

transmitters and tire valve caps l When removing or fitting the wheels, tires or the tire pressure warning valves and transmitters, contact your Toyota dealer as the tire pres- sure warning valves and transmitters may be damaged if not handled correctly.

l When replacing tire valve caps, do not use tire valve caps other than

those specified. The cap may become stuck.

n To avoid damaging the tire pressure warning valves and transmit-

ters Do not use liquid sealants on flat tires.

n Driving on rough roads

Take particular care when driving on roads with loose surfaces or pot- holes. These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition driving on rough roads may cause damage to the tires themselves, as well as the vehicle's wheels and body.

n If tire inflation pressures become low while driving

Do not continue driving, or your tires and/or wheels may be ruined.

274

4-3. Do-it-yourself maintenance Tire inflation pressure

n Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 370)

275

4-3. Do-it-yourself maintenance

n Inspection and adjustment procedure

Tire valve Tire pressure gauge

Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire. If you add too much air, press the center of the valve to lower. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Reinstall the tire valve cap.

276

4-3. Do-it-yourself maintenance

n Tire inflation pressure check interval

You should check tire pressure every two weeks, or at least once a month. Do not forget to check the spare tire.

n Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following: l Reduced fuel efficiency l Reduced driving comfort and tire life l Reduced safety l Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer.

n Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following: l Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.

l Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire infla- tion pressures that are even just a few pounds off can degrade ride and handling.

l Do not bleed or reduce tire inflation pressure after driving. It is normal

for the tire inflation pressure to be higher after driving.

l Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle is balanced.

277

4-3. Do-it-yourself maintenance

CAUTION

n Proper inflation is critical to save tire performance

Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. l Excessive wear l Uneven wear l Poor handling l Possibility of blowouts resulting from overheated tires l Poor sealing of the tire bead l Wheel deformation and/or tire separation l A greater possibility of tire damage from road hazards

NOTICE

n When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.

278

4-3. Do-it-yourself maintenance Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. n Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at your Toyota dealer. *: Conventionally referred to as “offset”. Toyota does not recommend using: l Wheels of different sizes or types l Used wheels l Bent wheels that have been straightened

n Aluminum wheel precautions (if equipped)

l Use only Toyota wheel nuts and wrench designed for use with

your aluminum wheels.

l When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1000 miles (1600 km).

l Be careful not to damage the aluminum wheels when using

tire chains.

l Use only Toyota genuine balance weights or equivalent and a

plastic or rubber hammer when balancing your wheels.

279

4-3. Do-it-yourself maintenance

n When replacing wheels

The wheels of your Toyota, except for the compact spare tire, are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P. 270)

CAUTION

n When replacing wheels

l Do not use wheels that are a different size from those recommended in

the Owner’s Manual, as this may result in loss of handling control.

l Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or seri- ous injury.

NOTICE

n Replacing tire pressure warning valves and transmitters

l Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.

l Ensure that only genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.

280

4-3. Do-it-yourself maintenance Air conditioning filter∗

The air conditioning filter must be changed regularly to maintain air conditioning efficiency. n Removal method

Turn the engine switch off.

Open the glove box.

Push in each side of the glove box to disconnect the claws.

Pinch the latches. Remove the filter cover.

∗: If equipped 281

4-3. Do-it-yourself maintenance

n Installing method

Pull out the filter. Rotate the filter to remove it.

Set a new filter. The “↑UP” marks shown on the filter should be pointing up. Rotate the filter. Push in the filter.

n Checking interval

Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

n If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

282

4-3. Do-it-yourself maintenance

NOTICE

n When using the air conditioning system

Make sure that a filter is always installed. Using the air conditioning system without a filter may cause damage to the system.

283

4-3. Do-it-yourself maintenance Key battery

Replace the battery with a new one if it is discharged. n You will need the following items:

l Flathead screwdriver (To prevent damage to the key, cover

the tip of the screwdriver with plastic tape.)

l Lithium battery CR2016

n Replacing the battery

Remove the cover.

Remove the module.

Remove the battery cover and the depleted battery.

Insert a new battery with the “+” terminal facing up.

284

4-3. Do-it-yourself maintenance

n If the key battery is discharged

The following symptoms may occur. l The wireless remote control will not function properly. l The operational range is reduced.

n Use a CR2016 lithium battery

l Batteries can be purchased at your Toyota dealer, jewelers, or camera

stores.

l Replace only with the same or equivalent type recommended by your

Toyota dealer.

l Dispose of used batteries according to the local laws.

CAUTION

n Removed battery and other parts

Keep away from children. These parts are small and if swallowed by a child, they can cause choking. Failure to do so could result in death or serious injury.

NOTICE

n For normal operation after replacing the battery

Observe the following precautions to prevent accidents. l Always work with dry hands.

Moisture may cause the battery to rust.

l Do not touch or move any other components inside the remote control. l Do not bend either of the battery terminals.

285

4-3. Do-it-yourself maintenance Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.

Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.

n Engine compartment

Type A

1.Push the tab in and lift the

cover off.

2.Remove the cover.

286

4-3. Do-it-yourself maintenance

Type B

Push the tab in and lift the lid off.

n Under the instrument panel

Type A

1.Open the auxiliary box.

2.Pull up the box and disen- gage the claws. Remove the stoppers from the cutouts and remove the box.

287

4-3. Do-it-yourself maintenance

Type B

Remove the lid.

After a system failure, see “Fuse layout and amperage ratings” (→P. 290) for details about which fuse to check.

Remove the fuse with the pull- out tool.

288

Check if the fuse has blown.

Type A

Type B

Type C

4-3. Do-it-yourself maintenance

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid

Normal fuse Blown fuse Contact your Toyota dealer.

289

4-3. Do-it-yourself maintenance

Fuse layout and amperage ratings

n Engine compartment (type A)

Fuse

Ampere

Circuit

ALT

120 A

2 MAIN

60 A

Charging system, HTR SUB2, EPS, ABS1/VSC1, HTR, ABS2/ VSC2, HTR SUB1, RDI, DEF, FR FOG, OBD2, D/L, POWER, RR DOOR, RL DOOR, STOP and AM1
EFI, HORN, AM2, ALT-S, DOME, ST, ECU-B, ETCS, HAZ, H-LP LH/ H-LP LO LH and H-LP RH/H-LP LO RH fuses

290

4-3. Do-it-yourself maintenance

n Engine compartment (type B)

Fuse

Ampere

Circuit

AM2

HORN

EFI

SPARE SPARE SPARE FR DEF

ABS2/VSC2

H-LP MAIN

10 ST 11 S-LOCK

12 DOME

15 A

10 A

20 A

30 A 10 A 15 A 20 A

30 A

30 A 30 A 20 A

15 A

Starting system, multiport fuel injection system/sequential multi- port fuel injection system Horn Multiport fuel injection system/ sequential multiport fuel injection system Spare fuse Spare fuse Spare fuse No circuit Anti-lock brake system, vehicle sta- bility control system No circuit Starting system No circuit Interior light, personal lights, theft deterrent system, audio system, wireless remote control system

291

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

13 ECU-B

7.5 A

Daytime running light system, front passenger occupant classification system, power windows, door lock system, theft deterrent system, meter and gauge, traction control system, vehicle stability control system Charging system Multiport fuel injection system/ sequential multiport fuel injection system, electronic throttle control system Turn signal lights, emergency flashers

7.5 A

10 A

10 A

10 A

Right-hand headlight

10 A

Left-hand headlight

10 A

40 A 50 A

50 A

40 A 30 A 30 A

30 A

50 A

Multiport fuel injection system/ sequential multiport fuel injection system Air conditioning system Electric power steering system Anti-lock brake system, vehicle sta- bility control system Air conditioning system Electric cooling fan Air conditioning system

No circuit

No circuit

14 ALT-S

15 ETCS

16 HAZ

17 H-LP RH/H-LP

LO RH

18 H-LP LH/H-LP

LO LH

19 EFI2

20 HTR SUB2
21 EPS

22 ABS1/VSC1

23 HTR 24 RDI 25 HTR SUB1
26 H-LP CLN/PWR

HTR 27 AMT

292

4-3. Do-it-yourself maintenance

n Under the instrument panel (type A)

Fuse

ACC2
DEF POWER

Ampere 7.5 A 40 A 30 A

Circuit

Shift lock system Rear window defogger Power windows

293

4-3. Do-it-yourself maintenance

n Under the instrument panel (type B)

Fuse

Ampere

Circuit

10 A

7.5 A

7.5 A

20 A

20 A

20 A

15 A

7.5 A

Side marker lights, parking lights, tail lights, license plate lights, multi- port fuel injection system/sequen- tial multiport fuel injection system Illuminations, instrument panel light control, meter and gauge Rear window defogger, air condi- tioning system No circuit Rear passenger’s power window (left side) Rear passenger’s power window (right side) Power outlet Door lock system, outside rear view mirrors, audio system

TAIL

PANEL 1

A/C

D DOOR

RL DOOR

RR DOOR

CIG

ACC

294

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

ID/UP/MIR HTR

10 A

10

IGN

11 MET 12 WIP 13 RR WIP 14 WSH

15 ECU-IG

7.5 A

7.5 A 25 A 15 A 15 A

10 A

16 GAUGE

10 A

17 OBD2

7.5 A

18 STOP

19 D/L 20 FR FOG

10 A

25 A 15 A

Multiport fuel injection system/ sequential multiport fuel injection system, outside rear view mirror control, outside rear view mirror heaters Multiport fuel injection system/ sequential multiport fuel injection system, SRS airbag system, front passenger occupant classification system Meter and gauge Windshield wiper Rear wiper Windshield washer Daytime running light system, anti- lock brake system, electric power steering system, power windows, door lock system, theft deterrent system, electric cooling fan Charging system, turn signal lights, emergency flashers, back-up lights, instrument panel light con- trol, shift lock system, rear window defogger, air conditioning system, automatic transmission system On-board diagnosis system Stop lights, high mounted stop- light, multiport fuel injection sys- tem/sequential multiport fuel injection system, shift lock system, anti-lock brake system Door lock system Front fog lights

295

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

21 AM1

25 A

Multiport fuel injection system/ sequential multiport fuel injection system

n After a fuse is replaced

If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (→P. 297) If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer.

n If there is an overload in the circuits

The fuses are designed to blow before the entire wiring harness is damaged.

CAUTION

n To prevent system breakdowns and vehicle fire

Observe the following precautions. Failing to do so may cause damage, and possibly a fire or injury. l Never use a fuse of a higher amperage rating than indicated, or use any

other object in place of a fuse.

l Always use a genuine Toyota fuse or equivalent.

Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.

l Do not modify the fuse or the fuse box.

NOTICE

n Before replacing fuses

Have the cause of electrical overload determined and repaired by your Toyota dealer as soon as possible.

296

4-3. Do-it-yourself maintenance Light bulbs

You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. n Prepare a replacement light bulb.

Check the wattage of the light bulb being replaced. (→P. 366)

n Front bulb locations

Front side marker lights

Front turn signal lights

Headlights and daytime running lights (if equipped)

Parking lights

Front fog lights (if equipped)

297

4-3. Do-it-yourself maintenance

n Rear bulb locations

Stop/tail and rear side marker lights

Rear turn signal lights Back-up lights

Replacing light bulbs

License plate light

n Headlights and daytime running lights (if equipped) Unplug the connector.

Remove the rubber cover.

298

4-3. Do-it-yourself maintenance

Release spring.

the bulb

retaining

Remove the bulb.

To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.

n Front fog lights (if equipped)

Remove the bolts and clips.

Partly remove the fender liner.

299

4-3. Do-it-yourself maintenance

Unplug depressing the lock release.

the connector while

Turn the bulb counterclockwise.

n Front side marker lights

Turn the bulb base counterclock- wise.

Remove the light bulb.

300

4-3. Do-it-yourself maintenance

n Front turn signal lights

Turn the bulb base counterclock- wise.

Remove the light bulb.

n Parking lights

Turn the bulb base counterclock- wise.

301

4-3. Do-it-yourself maintenance

Remove the light bulb.

n Back-up lights, stop/tail and rear side marker lights and rear

turn signal lights

Open the back door and remove the cover.

Use a flathead screwdriver which is wrapped with a cloth.

Turn the bulb base counterclock- wise.

Stop/tail and rear side marker lights Rear turn signal light Back-up light

Remove the light bulb.

Stop/tail and rear side marker lights Rear turn signal light Back-up light

302

4-3. Do-it-yourself maintenance

n License plate light

Disengage remove the license plate light.

claws

the

and

Use a flathead screwdriver which is wrapped with a cloth.

Turn the bulb base counterclock- wise.

Remove the light bulb.

n Lights other than the above

If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. • Side turn signal lights • High mounted stoplight

303

4-3. Do-it-yourself maintenance

n Condensation build-up on the inside of the lens

Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. l Large drops of water are built up on the inside of the lens. l Water has built up inside the headlight.

n LED high mounted stoplight

The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

n Installing the clips

Insert the clips.

CAUTION

n Replacing light bulbs

Turn off the headlights. Do not attempt to replace the bulb immediately after turning off the headlights. The bulbs become very hot and may cause burns.

n To prevent damage or fire

Make sure bulbs are fully seated and locked.

304

4-3. Do-it-yourself maintenance

NOTICE

l Halogen bulbs have pressurized gas inside and require special handling. Do not touch the glass portion of the light bulb with bare hands. Hold the bulb by the plastic or metal portion. If the bulb is scratched or dropped it may blow out or crack.

l Fully install light bulbs and any parts used to secure them. Failing to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.

305

4-3. Do-it-yourself maintenance

306

5-1. Essential information Emergency flashers

Use the emergency flashers if the vehicle malfunctions or is involved in an accident.

Press the switch to flash all the turn signal lights. To turn them off, press the switch once again.

NOTICE

n To prevent battery discharge

Do not leave the emergency flashers on longer than necessary when the engine is not running.

308

5-1. Essential information If your vehicle needs to be towed

If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws. If towing from the front, the vehicle's rear wheels and axles must be in good condition. (→P. 312) If they are damaged, use a towing dolly or flat bed truck.

Before towing

The following may indicate a problem with your transmission. Contact your Toyota dealer before towing. l The engine is running, but the vehicle will not move. l The vehicle makes an abnormal sound.

Emergency towing

If a tow truck is not available, in an emergency your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet. This should only attempted on hard, surfaced roads for short distances at low speeds. A driver must be in the vehicle to steer and operate the brakes. The vehicle’s wheels, drive train, axles, steering and brakes must be in good condition.

Towing eyelet

309

5-1. Essential information

n Emergency towing procedure

Release the parking brake. Put the transmission in N. Turn the engine switch to the ACC (engine off) or ON (engine run- ning) position.

CAUTION

n Caution while towing

l Use extreme caution when towing the vehicle.

Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing eyelet and the cables or chains. Always use caution for the surroundings and other vehicles while towing. If the engine is not running, the power assist for the brakes and steering will not function, making steering and braking more difficult.

NOTICE

n To prevent causing serious damage to the transmission

(vehicles with an automatic transmission) Never tow this vehicle from the rear with the front wheels on the ground. This may cause serious damage to the transmission.

n When towing a vehicle without using a towing dolly

(vehicles with a manual transmission) Do not tow with the key removed or in the LOCK position.

310

Installing towing eyelet

5-1. Essential information

Remove the eyelet cover using a flathead screwdriver.

To protect the bodywork, place a rag between the screwdriver and the vehicle body, as shown in the illustration.

Insert the towing eyelet into the hole and tighten partially by hand.

Tighten down the towing eyelet securely using a wheel nut wrench.

n Location of the emergency towing eyelet

→P. 329

311

5-1. Essential information

CAUTION

n Installing towing eyelet to the vehicle

Make sure that towing eyelet is installed securely. If not securely installed, towing eyelet may come loose during towing. This may lead to accidents that cause serious injury or even death.

Towing with a sling-type truck

NOTICE

n To prevent body damage

Do not tow with a sling-type truck, either from the front or rear.

Towing with a wheel lift-type truck from the front

Release the parking brake.

312

5-1. Essential information

NOTICE

n To prevent damaging the vehicle

When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.

Towing with a wheel lift-type truck from the rear

Vehicles with an automatic trans- mission: Use a towing dolly under the front wheels. Vehicles with a manual transmis- sion: We recommend to use a towing dolly under front wheels.

the

When not using a towing dolly, turn the engine switch to the ACC position and shift the shift lever to N.

NOTICE

n To prevent causing serious damage to the transmission

(vehicles with an automatic transmission) Never tow this vehicle from the rear with the front wheels on the ground.

n To prevent damaging the vehicle (vehicles with a manual transmission)

l Do not tow the vehicle with the key removed or in the LOCK position.

The steering lock mechanism is not strong enough to hold the front wheel straight.

l When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.

313

If your Toyota is transported by a flat bed truck, it should be tied down at the locations shown in the illustration.

If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. Apply the parking brake firmly.

5-1. Essential information

Using a flat bed truck

Front

314

5-1. Essential information If you think something is wrong

If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. n Visible symptoms

l Fluid leaks under the vehicle

(Water dripping from the air conditioning after use is normal.)

l Flat-looking tires or uneven tire wear l High engine coolant temperature warning light flashes or

comes on

l Low engine coolant temperature indicator comes on or does

not come on continuously

n Audible symptoms

l Changes in exhaust sound l Excessive tire squeal when cornering l Strange noises related to the suspension system l Pinging or other noises related to the engine

n Operational symptoms

l Engine missing, stumbling or running rough l Appreciable loss of power l Vehicle pulls heavily to one side when braking l Vehicle pulls heavily to one side when driving on a level road l Loss of brake effectiveness, spongy feeling, pedal almost

touches the floor

315

5-1. Essential information Fuel pump shut off system

To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine.

Follow the procedure below to restart the engine after the system is activated.

Turn the engine switch to the ACC or LOCK position. Restart the engine.

NOTICE

n Before starting the engine

Inspect the ground under the vehicle. If you find that fuel has leaked onto the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine.

316

5-1. Essential information Event data recorder

Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.

In a crash or a near car crash event

The SRS airbag sensor assembly contains the EDR. In a crash or a near car crash event, this device may record some or all of the follow- ing information: l Engine speed l Whether the brake pedal was applied or not l Vehicle speed l To what extent the accelerator pedal was depressed l Position of the transmission shift lever l Whether the driver and front passenger wore seat belts or not l Driver’s seat position l SRS airbag deployment data l SRS airbag system diagnostic data l Front passenger’s occupant classification The information above is intended to be used for the purpose of improving vehicle safety performance. Unlike general data recorders, the EDR does not record sound data such as conversation between passengers.

317

5-1. Essential information

Disclosure of the data

Toyota will not disclose the data recorded in an EDR to a third party except when: l An agreement from the vehicle’s owner (or the leasing company for

a leased vehicle) is obtained

l Officially requested by the police or other authorities l Used as a defense for Toyota in a law suit l Ordered by a court of law However, if necessary Toyota will: l Use the data for research on Toyota vehicle safety performance l Disclose the data to a third party for research purposes without dis- closing details of the vehicle owner, and only when it is deemed necessary

l Disclose summarized data cleared of vehicle identification informa-

tion to a non-Toyota organization for research purposes

318

5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds...

Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system.

Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.

The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

(except Canada)

(Canada)

Brake system warning light (warning buzzer)* • Low brake fluid • Malfunction in the brake system (vehicles with the ABS) This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released, the system is operating nor- mally.

*: Parking brake engaged warning buzzer:

The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reach a speed of approximately 3 mph [5 km/h])

319

5-2. Steps to take in an emergency

Stop the vehicle immediately.

The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Charging system warning light Indicates a malfunction in the vehicle’s charging sys- tem.

Low engine oil pressure warning light Indicates that the engine oil pressure is too low*.

High engine coolant temperature warning light Indicate a engine is almost overheating.(→P. 349)

*: The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the engine oil level dipstick.

Have the vehicle inspected immediately.

Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately.

Warning light

Warning light/Details

(except Canada)

(Canada)

Malfunction indicator lamp Indicates a malfunction in: • The electronic engine control system; • The electronic throttle control system; • The electronic automatic transmission control sys- tem; or • Emission control system.

320

5-2. Steps to take in an emergency

Warning light

Warning light/Details

SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system.

(except Canada)

ABS warning light (if equipped) Indicates a malfunction in the ABS.

(Canada)

Electric power steering warning light Indicates a malfunction in the EPS (Electric Power Steering) system. Slip indicator (if equipped) The indicator light comes on to indicate a malfunc- tion in; • The VSC; or • The TRAC.

321

5-2. Steps to take in an emergency

Follow the correction procedures.

After taking the specified steps to correct the suspected problem, check that the warning light turns off.

Warning light

Warning light/Details

Correction procedure

Open door warning light Indicates that a door is not fully closed. Driver’s seat belt reminder light (warning buzzer)*1
Warns the driver to fas- ten his/her seat belt. Front passenger’s seat belt reminder light (warning buzzer)*2
Warns the front passen- ger to fasten his/her seat belt. Tire pressure warning light • When the light comes on: Low tire inflation pres- sure. • When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warning system.

Low washer fluid warn- ing light Low level of washer fluid

Check that all doors are closed.

Fasten the seat belt.

Fasten the seat belt.

Adjust the tire inflation pressure.

Have the system checked by your Toyota dealer.

Fill the tank.

(On the instrument

cluster)

(On the center panel)

(except Canada)

(if equipped)

322

5-2. Steps to take in an emergency

Warning light

Warning light/Details

Correction procedure

(except Canada)

Engine oil replacement reminder light • Illuminates for about 3 seconds and then flashes for about 12 seconds: Indi- cates that the engine oil is scheduled to be changed. • Comes on and remains: Indicates that the engine oil should be changed.

Check the engine oil, and change if neces- sary.

Check and change the engine oil.

*1: Driver's seat belt reminder:

The driver’s seat belt reminder sounds to alert the driver that his or her seat belt is not fastened. Once the engine switch is turned to the ON or START position, the buzzer sounds for 6 seconds. If the vehicle has reached a speed of at least 12 mph (20 km/h), the buzzer sounds intermittently for approximately 10 seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for approximately 20 more seconds.

*2:Front passenger’s seat belt reminder:

The front passenger’s seat belt reminder sounds to alert the front passenger that his or her seat belt is not fastened. The buzzer sounds intermittently for approximately 10 seconds after the vehicle has reached a speed of at least 12 mph (20 km/h). Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for approximately 20 more seconds.

323

5-2. Steps to take in an emergency

n Key reminder buzzer

The buzzer indicates that the key has not been removed (with the engine switch in the ACC or LOCK position and the driver’s door opened).

n Light reminder buzzer

The buzzer indicates that the headlight switch is left on (with the key removed and the driver’s door opened).

n If the malfunction indicator lamp comes on while driving

First check the following:

Is your vehicle low on gas? If it is, refuel the vehicle immediately. Is the fuel tank cap loose? If it is, tighten it securely.

The light will go off after taking several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible.

n Front passenger detection sensor and passenger seat belt reminder

If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light to flash and buzzer to sound.

n When the tire pressure warning light comes on

Check the tire inflation pressure and adjust to the appropriate level.

n The tire pressure warning light may turn on due to natural causes

The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temper- ature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).

n When a tire is replaced with a spare tire

The compact spare tire is not equipped with the tire pressure warning valve and transmitter. If a tire goes flat, the tire pressure warning light will not turn off even though the flat tire is replaced with the spare tire. Replace the spare tire with the repaired tire and adjust the proper tire inflation pressure. The tire pressure warning light will turn off after a few minutes.

324

5-2. Steps to take in an emergency

n If the tire pressure warning system is inoperative

The tire pressure warning system will be disabled in the following condi- tions: (When the condition becomes normal, the system will work properly.)

If tires not equipped with tire pressure warning valves and transmit- ters are used. If the ID code on the tire pressure warning valves and transmitters is not registered in the tire pressure warning computer. If the tire inflation pressure is 73 psi (500 kPa, 5.1 kgf/cm2 or bar) or higher.

The tire pressure warning system may be disabled in the following condi- tions: (When the condition becomes normal, the system will work properly.)