1-1. Key information
Using the mechanical key (vehicles with smart key system)
Take out the mechanical key.
After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery depletes or entry function does not operate prop- erly, you will need the mechanical key. (P. 469)
■Key number plate
Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made at your Toyota dealer using the key number plate. (P. 468)
■When riding in an aircraft
When bringing a key onto an aircraft, make sure you do not press any but- tons on the key while inside the aircraft cabin. If you are carrying a key in your bag etc., ensure that the buttons are not likely to be pressed acciden- tally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.
NOTICE
■To prevent key damage
●Do not subject the keys to strong shocks, expose them to high tempera-
tures by placing them in direct sunlight, or get them wet.
●Do not expose the keys to electromagnetic materials or attach any mate-
rial that blocks electromagnetic waves to the key surface.
●Do not disassemble the key.
29
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors Smart key system
The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)
Locks and unlocks the doors (P. 31) Locks and unlocks the doors (P. 32) Starts and stops the engine (P. 171)
30
: If equipped
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Unlocking and locking the doors
Front door handle
Grip the driver’s door handle to unlock the door. Grip the passen- ger’s door handle to unlock all the doors.*
Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 seconds after the doors are locked. *: The door unlock settings can
be changed.(P. 36)
Touch the sensor area to lock the doors.
31
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Back door
the unlock button
Press unlock the door.
to
the door
The door cannot be unlocked for 3 seconds after is locked. Lock the back door again when you leave the vehicle. The back door will not lock automatically after it has been opened and then closed.
Press the lock button to lock the doors.
32
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Antenna location and effective range
■ Antenna location
Antennas outside cabin Antennas inside cabin Antenna outside luggage com- partment
33
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■ Effective range (areas within which the electronic key is
detected)
When locking or unlock- ing the doors The system can be oper- ated when the electronic key is within about 2.3 ft. (0.7 m) of an outside door handle. When starting the engine or changing “ENGINE START STOP” switch modes The system can be oper- ated when the electronic key is inside the vehicle.
34
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■Operation signals
A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)
■When the door cannot be locked using the topside sensor area
If the door will not lock even when the topside sensor area is touched, try touch- ing both the topside and underside sen- sor areas at the same time.
■Conditions affecting operation
The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system and wireless remote control from operating properly. (Way of coping P. 469) ●When the electronic key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise
●When carrying a portable radio, cellular phone, cordless phone or other
wireless communication devices
●When the electronic key has come into contact with, or is covered by a
metallic object
●When multiple electronic keys are in the vicinity ●When carrying or using the electronic key together with the following
devices that emit radio waves • Another vehicle’s electronic key • A wireless key that emits radio waves • Personal computer
●If window tint with a metallic content or metallic objects are attached to
the rear window
35
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■Switching the door unlock function
It is possible to set which doors the entry function unlocks.
STEP 1
Turn the “ENGINE START STOP” switch OFF. When the indicator on the key surface is turned off, press and hold on
for approximately 5 seconds while pressing
STEP 2
or the key.
The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat
STEP 2
.)
Multi-information
display
(TFT type only)
Unlocking function
Beep
Hold the driver’s door han- dle to unlock only the driver’s door. Hold the front passenger’s door handle to unlock all doors. Hold either front door han- dle to unlock all doors.
Exterior: Beeps three times Interior: Pings once
Exterior: Beeps twice Interior: Pings once
STEP 3
For vehicles equipped with an alarm: To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 second after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (P. 111)
36
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■Battery-saving function
In the following circumstances, the entry function is disabled in order to pre- vent the vehicle and electronic key batteries from discharging. ●When the entry function has not been used for 2 weeks or more ●When the electronic key has been left within approximately 3 ft. (1 m) of
the vehicle for 10 minutes or more
The system will resume operation when... ●The vehicle is locked using the door handle lock switch. ●The vehicle is locked/unlocked using the wireless remote control function
(P. 45) or the mechanical key. (P. 469)
■Electronic key battery depletion
●The standard battery life is 1 to 2 years. (The battery becomes depleted even if the electronic key is not used.) If the smart key system or the wireless remote control function does not operate, or the detection area becomes smaller, the battery may be depleted. Replace the battery when necessary. (P. 399)
●If the battery becomes low, an alarm will sound in the cabin when the
engine stops. (P. 40)
●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field. • TVs • Personal computers • Recharging cellular phones or cordless phones • Table lamps
37
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■To operate the system properly
Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention may not func- tion.)
■Note for the entry function
●Even when the electronic key is within the effective range (detection
areas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
• The electronic key is near the ground or in a high place, or too close to
the rear bumper center when the back door is locked or unlocked.
• The electronic key is on the instrument panel, floor or in the glove box when the engine is started or “ENGINE START STOP” switch modes are changed.
●Do not leave the electronic key on top of the instrument panel or near the door pockets when exiting the vehicle. Depending on the radio wave reception conditions, it may be detected by the antenna outside the cabin and the door will become lockable from the outside, possibly trapping the electronic key inside the vehicle.
●As long as the electronic key is within the effective range, the doors may
be locked or unlocked by anyone.
38
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
●Even if the electronic key is not inside the vehicle, it may be possible to
start the engine if the electronic key is near the window.
●The doors may unlock or lock if a large amount of water splashes on the door handle, such as in the rain or in a car wash when the electronic key is within the effective range. (The doors will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)
●If the key is kept near the vehicle while it is being washed, water applied to a door handle may cause the door to lock and unlock repeatedly. In this event, place the key in a location 6 ft. (2 m) or more from the vehicle, taking care not to lose the key.
●If the key is inside the vehicle while it is being washed, water applied to a door handle may cause a buzzer to sound. In this event, locking all doors will cause the buzzer to stop sounding.
●It may not be possible to lock the doors if the sensor area is covered by mud, ice, snow etc. In this event, try locking again after cleaning the area, or lock by touching the sensor area on the underside of the door handle.
●Gripping the door handle when wearing a glove may not unlock or lock
the door.
●If the wireless remote control is used to lock the doors when the elec- tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the smart key system. (Use the wireless remote control to unlock the doors.)
●A sudden approach to the effective range or door handle operation may prevent the doors from being unlocked. In this case, return the door han- dle to the original position and check that the doors unlock before pulling the door handle.
39
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■When the vehicle is not driven for extended periods
To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2
m) of the vehicle.
■Security feature
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
■Alarms and warning indicators
A combination of exterior and interior alarms as well as warnings displayed on the multi-information display are used to prevent theft of the vehicle and unforeseeable accidents resulting from erroneous operation. Perform the appropriate correction procedure described in the following table.
Alarm
Situation
Correction procedure
Exterior alarm sounds once for 10 seconds
Exterior alarm sounds once for 10 seconds
Exterior alarm sounds once for 10 seconds
An attempt was made to lock the doors using the entry function while the electronic key was still inside the passenger com- partment An attempt was made to exit the vehicle and lock the doors without first turn- ing the “ENGINE START STOP” switch OFF An attempt was made to lock the vehicle while a door is open
Retrieve the elec- tronic key from the passenger compart- ment and lock the doors again
Turn the “ENGINE START STOP” switch OFF and lock the doors again
Close all of the doors and lock the doors again
40
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Alarm
Situation
Correction procedure
The “ENGINE START STOP” switch was turned to ACCESSORY mode while the driver’s door was open (or the driver’s door was opened while the “ENGINE START STOP” switch was in ACCES- SORY mode) The “ENGINE START STOP” switch was turned OFF while the driver’s door was open When the “ENGINE START STOP” switch is in IGNITION ON or ACCES- SORY mode, an attempt was made to open the door and exit the vehicle, and the shift lever was not in “P” When the “ENGINE START STOP” switch is in IGNITION ON or ACCES- SORY mode, the driver’s door was closed after the key was carried outside the vehicle, and the shift lever not in “P”
Turn the “ENGINE START STOP” switch OFF and close the driver’s door
Close the driver’s door
Shift the shift lever to “P” and turn the “ENGINE START STOP” switch OFF
Shift the shift lever to “P”, turn the “ENGINE START STOP” switch OFF and close the driver’s door again
Interior alarm
pings continu-
ously*1
Interior alarm
sounds continu-
ously*1
Interior and exte-
rior alarms sound
continuously*1
41
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Alarm
Situation
Interior alarm
pings once*1
Interior alarm
pings once and
exterior alarm
sounds 3 times*1
The electronic key has a low battery An attempt was made to start the engine without the electronic key being present, or the electronic key was not functioning normally The driver’s door was closed after the key was carried outside the vehicle, and the “ENGINE START STOP” switch was not turned OFF An occupant carried the electronic key outside the vehicle and closed the door while the “ENGINE START STOP” switch was not OFF
Correction procedure Replace the electronic key battery
Start the engine with
the electronic key
present*2
Turn the “ENGINE START STOP” switch OFF and close the driver’s door again
Bring the electronic key back into the vehi- cle
*1: A message will be shown on the multi-information display in the instru-
ment cluster.
*2: If the engine does not start when the electronic key is inside the vehicle, the electronic key battery may be depleted or there may be difficulties receiving signal from the key. (P. 469)
42
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■If the smart key system does not operate properly
●Locking and unlocking the doors: Use the mechanical key. (P. 469) ●Starting the engine (P. 470)
■When the electronic key battery is fully depleted
P. 399
■Customization
Settings (e.g. smart key system) can be changed. (Customizable features P. 519)
■Certification for the smart key system
FCC ID: HYQ14ADF FCC ID: HYQ13CZE
For vehicles sold in the U.S.A. FCC ID: HYQ14ACX FCC ID: HYQ13CZD NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user’s authority to operate the equip- ment.
43
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
For vehicles sold in Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION
■Caution regarding interference with electronic devices
●People with implanted pacemakers or cardiac defibrillators should keep
away from the smart key system antennas. (P. 33) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.
●Users of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
Ask your Toyota dealer for details for disabling the smart key system.
44
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors Wireless remote control
The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle.
Vehicles with smart key system
Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pressing Opens and closes power door equipped) Pressing Sounds alarm (P. 114)
holding: the (if
holding:
back
and
and
45
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Vehicles without smart key system
and
holding:
Locks all doors Pressing Sounds alarm (P. 114) Unlocks all doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Pressing Opens and closes power door equipped)
holding: the (if
back
and
■Operation signals
Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)
Back door: A buzzer sounds and the emergency flashers flash twice to indi-
cate that the back door has been opened/closed.
46
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■Door lock buzzer
If a door or back door is not fully closed, a buzzer sounds continuously for 10
seconds if an attempt to lock the door is made. Fully close the door to stop
the buzzer, and lock the vehicle once more.
■Security feature
P. 40
■Alarm
Using the wireless remote control to lock the door will set the alarm system. (P. 111)
■Key battery depletion
Vehicles with smart key system
P. 399
Vehicles without smart key system
The standard battery life is 1 to 2 years. (The battery becomes depleted
even if the key is not used.) If the wireless remote control function does
not operate, the battery may be depleted. Replace the battery when nec-
essary. (P. 400)
■If the wireless remote control does not operate properly
Vehicles with smart key system Locking and unlocking the doors: Use the mechanical key. (P. 469) Vehicles without smart key system Locking and unlocking the doors: Use the key. (P. 50)
47
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■Conditions affecting operation
Vehicles with smart key system
P. 35
Vehicles without smart key system
The wireless remote control function may not operate normally in the fol-
lowing situations.
●Near a TV tower, radio station, electric power plant, airport or other
facility that generates strong radio waves
●When carrying a portable radio, cellular phone or other wireless com-
munication device
●When multiple wireless keys are in the vicinity ●When the wireless key has come into contact with, or is covered by a
metallic object
●When a wireless key (that emits radio waves) is being used nearby ●When the wireless key has been left near an electrical appliance such
as a personal computer
■Customization
Settings (e.g. 2-step unlocking function) can be changed. (Customizable features P. 519)
■Reversing the operation of the power back door (if equipped)
Pressing the wireless remote control switch again while the power back door is operating will cause the operation to reverse. However, the reverse opera- tion cannot be performed for the first second after automatic operation starts, even if the wireless remote control switch is pressed again.
48
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■Certification for wireless remote control
For vehicles sold in the U.S.A. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio com- munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver. ●Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user’s authority to operate the equip- ment. For vehicles sold in Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
49
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors Side doors
The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with smart key system)
P. 30
■ Wireless remote control
P. 45
■ Key
Vehicles with smart key system The doors can also be locked and unlocked with the mechan- ical key. (P. 469) Vehicles without smart key system
Locks all doors Unlocks all doors Turning the key unlocks the driver’s door. Turning the key again within 3 seconds unlocks the other doors.
50
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■ Door lock switch
Locks all doors Unlocks all doors
■ Inside lock button
Locks the door Unlocks the door The front doors can be opened by pulling the inside handles even if the lock buttons are in the lock position.
51
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Locking the driver’s doors from the outside without a key
STEP 1
STEP 2
Move the inside lock button to the lock position. Close the door.
Vehicles with smart key system The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. Depending on the position of the electronic key, the key may not be detected correctly and the door may be locked. Vehicles without smart key system The door cannot be locked if either front door is open and the key is in the engine switch.
Rear door child-protector lock
The door cannot be opened from inside the vehicle when the lock is set.
Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
52
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Automatic door locking and unlocking systems
The following functions can be set or canceled:
Function
Shift position linked door locking function Shift position linked door unlocking function Speed linked door lock- ing function
Driver’s door linked door unlocking function
Operation
Shifting the shift lever out of “P” locks all doors. Shifting the shift lever to “P” unlocks all doors. All doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher. All doors are unlocked when the driver’s door is opened within 10 seconds after turning the “ENGINE START STOP” switch OFF.
■ Setting and canceling the functions
Vehicles with TFT type multi-information display The function settings can be changed using the multi-informa- tion display. (P. 526) Vehicles with LCD type multi-information display To switch between setting and canceling, follow the procedure below:
53
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
STEP 1
STEP 2
Vehicles with smart key system: Close all the doors and switch the “ENGINE START STOP” switch to IGNITION ON mode. (Perform within 20 sec- onds.) Vehicles without smart key system: Close all the doors and switch the engine switch to the “ON” position. (Perform
within 20 seconds.)
STEP 2
STEP 2
Shift the shift lever to “P” or “N”,
press and hold the driver’s door
lock switch (
) for about 5
seconds then release.
or
to
corresponding
The shift lever and switch posi- tions the desired function to be set are shown as follows. Use the same procedure to can- cel the function.
Function
Shift lever position
Driver’s door lock switch position
Shift position linked door lock- ing function Shift position linked door unlocking function Speed linked door locking func- tion Driver’s door linked door unlock- ing function
“P”
“N”
When the setting or canceling operation is complete, all doors are locked and then unlocked.
54
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■Impact detection door lock release system
In the event that the vehicle is subject to a strong impact, all the doors are unlocked. Depending on the force of the impact or the type of accident, however, the system may not operate.
■Customization
Settings (e.g. unlocking function using a key) can be changed. (Customizable features P. 519)
CAUTION
■To prevent an accident
Observe the following precautions while driving the vehicle. Failing to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.
The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in death or serious injury. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
●Set the rear door child-protector locks when children are seated in the rear
seat.
55
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors Back door
The back door can be opened using the back door opener. The back door can be locked and unlocked using the entry function (vehicles with smart key system), wireless remote control or door lock switch. In addition, the power back door (if equipped) can be opened using the power back door switch or wireless remote control. ■ Unlocking and locking the back door
Entry function (vehicles with smart key system)
P. 30
Wireless remote control
P. 45
Door lock switch
P. 50
■ Opening the back door from outside the vehicle
Back door opener
Raise the back door while pushing up the back door opener switch.
Wireless remote control (vehicles with power back door)
P. 45
56
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■ Opening the back door from inside the vehicle (vehicles
with power back door)
Push and hold the switch to open/close. Pressing the switch again while the power back door is operating will cause the opera- tion to reverse. However, the reverse opera- tion cannot be performed for the first second after pressing the switch to operate the door.
Lower the back door using the back door handle, and make sure to push the back door down from the outside to close it.
Be careful not to pull the back door sideways when closing the back door with the handle.
57
When closing the back door
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Power back door switch (vehicles with power back door)
Push the switch to close.
Pressing the switch again while the power back door is closing will cause it to open again. However, the reverse operation cannot be performed for the first second after pressing the switch to close the door.
The back door can be opened even if it is locked. Lock the back door again when you leave the vehicle. The back door will not lock auto- matically after it has been opened and then closed. A buzzer sounds and the emergency flashers flash twice to indicate that the back door has been opened/closed.
58
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Canceling the power back door system (vehicles with power back door)
Turn the main switch to disable the power back door system.
Inoperative Operative The back door cannot be oper- ated even with the wireless remote control or power back door switch. A buzzer will sound twice if the power back door switch is pressed while the power back door system is inoperative.
59
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■The power back door can be opened/closed when (vehicles with power
back door)
Vehicles with smart key system ●The “ENGINE START STOP” switch is in IGNITION ON mode, and
the shift lever is in “P”.
●The “ENGINE START STOP” switch is in OFF or ACCESSORY
mode.
Vehicles without smart key system ●The engine switch is in the “ON” position, and the shift lever is in “P”. ●The engine switch is in the “LOCK” or “ACC” position.
■Jam protection function (vehicles with power back door)
If anything obstructs the power back door while it is closing/opening, the back door will automatically operate in the opposite direction.
■If the power back door does not work (vehicles with power back door) The back door must be initialized. To initialize, close the back door com- pletely by hand.
■Back door closer
In the event that the back door is left slightly open, the back door closer will automatically close it to the fully closed position.
60
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
CAUTION
■While driving
●Keep the back door closed while driving.
If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door before driving.
●Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident.
●Never let anyone sit in the luggage compartment. In the event of sudden
braking or a collision, they are susceptible to death or serious injury.
■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to play in the luggage compartment.
If a child is accidentally locked in the luggage compartment, they could have heat exhaustion or other injuries.
●Do not allow a child to open or close the back door.
Doing so may cause the back door to move unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.
61
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
CAUTION
■Operating the back door
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●Remove any heavy loads, such as snow and ice, from the back door before opening it. Failure to do so may cause the back door to suddenly shut again after it is opened.
●When opening or closing the back door, thoroughly check to make sure
the surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●Use caution when opening or closing the back door in windy weather as it
may move abruptly in strong wind.
●The back door may suddenly shut if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage com- partment.
62
VENZA_OM_OM73019U_(U)
1
CAUTION
1-2. Opening, closing and locking the doors
●When closing the back door, take extra care to prevent your fingers etc. from being caught.
●When closing the back door, make sure to press it lightly on its outer surface. If the back door handle is used to fully close the back door, it may result in hands or arms being caught.
●Do not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay. Doing so may cause hands to be caught or the back door damper stay to break, causing an accident.
●If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended.
■Back door closer
It
●In the event that the back door is left slightly open, the back door closer will automatically close it to the fully closed position. takes several seconds before the back door closer begins to operate. Be careful not to catch fingers or anything else in the back door, as this may cause bone fractures or other serious injuries.
●Use caution when using the back door closer as it still operates when the
power back door system is cancelled.
63
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
CAUTION
■Power back door (if equipped)
Observe the following precautions when operating the power back door. Failure to do so may cause death or serious injury. ●Check the safety of the surrounding area to make sure there are no obsta-
cles or anything that could cause any of your belongings to get caught.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●On an incline, the back door may suddenly shut after it opens. Make sure
the back door is fully open and secure.
●In the following situations, the power back door may detect an abnormality and automatic operation may be stopped. In this case, the back door has to be operated manually. Take extra care when on an incline, as the back door may open or close abruptly. • When the back door contacts an obstacle • Vehicles with smart key system:
When the battery voltage suddenly drops, such as when the “ENGINE START STOP” switch is turned to IGNITION ON mode or the engine is started during automatic operation Vehicles without smart key system: When the battery voltage suddenly drops, such as when the engine switch is turned to the “ON” position or the engine is started during automatic operation
●If a bicycle carrier or similar heavy object is attached to the back door, the power back door may not operate, causing itself to malfunction, or the back door may suddenly shut again after being opened, causing some- one’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recom- mended.
64
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
CAUTION
■Jam protection function (vehicles with power back door)
Observe the following precautions. Failure to do so may cause death or serious injury. ●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just before the back door fully closes. Be careful not to catch fingers or any- thing else.
●The jam protection function may not work depending on the shape of the
object that is caught. Be careful not to catch fingers or anything else.
NOTICE
■Back door damper stays
The back door is equipped with damper stays that hold the back door in place. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction.
Damper stay
●Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod.
●Do not touch the damper stay rod with
gloves or other fabric items.
●Do not attach any accessories other than genuine Toyota parts to the back door.
●Do not place your hand on the damper
stay or apply lateral forces to it.
65
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
NOTICE
■To prevent back door closer malfunction
Do not apply excessive force to the back door while the back door closer is operating.
■To prevent damage to the power back door (vehicles with power back
door) ●Make sure that there is no ice between the back door and frame that would prevent movement of the back door. Operating the power back door when excessive load is present on the back door may cause a malfunc- tion.
●Do not apply excessive force to the back door while the power back door
is operating.
●Take care not to damage the sensors (installed on the right and left edges of the power back door) with a knife or other sharp object. If the sensor is disconnected, the power back door will not operate in automatic operation.
66
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats
Power seat
angle
control
Seat position fore/aft control switch Seatback switch Seat cushion (front) angle control switch (driver’s side only) Vertical switch (driver’s side only) Lumbar switch
support
height
control
control
Manual seat
Seat position fore/aft adjust- ment lever Seatback angle adjustment lever
67
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Active head restraints
When the occupant’s lower back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward and upward to help reduce the risk of whiplash on the seat occupant.
■Active head restraints
Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may make the inner struc- ture of the head restraint appear. This does not indicate a problem.
During rear-end collision
Inner structure
68
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
●Be careful that the seat does not hit passengers or luggage. ●Do not recline the seat more than necessary when the vehicle is in motion
to reduce the risk of sliding under the lap belt. If the seat is too reclined, during an accident the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury.
●Manual seat only: After adjusting the seat, make sure that the seat is
locked in position.
69
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats
Seatback angle adjustment lever
Pull up the lever until the lock is completely released.
Folding down the rear seatbacks
■ Before folding down the rear seatbacks
STEP 1
Stow the seat belt buckles and lower the head restraints to the lowest position.
70
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 2
Pass the outer seat belts and plates the seat belt hangers.
through
This prevents the shoulder belt from being damaged. Make sure that the seat belts are removed from the hangers before using them.
■ Folding down the rear seatbacks
From inside
Fold down the seatback while pulling seatback angle adjustment lever.
the
Pull up the lever until the lock is completely released.
Pull the lever.
For left side rear seatback For right side and center rear seatback
71
From outside
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
Do not recline the seat more than necessary when the vehicle is in motion, to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.
■Before folding down a rear seat
Do not fold down a rear seat when there are passengers sitting in the rear seats or when there is luggage placed on the rear seats.
■When returning the seatbacks to their original position
Observe the following precautions. Failure to do so may result in death or serious injury. ●Be careful not to get your hands pinched in the seat. ●Make sure the seatbacks are securely locked by lightly rocking it back and
forth.
●Check that the seat belts are not twisted or caught under the seat. ●Arrange the seat belts in the proper positions for ready use.
NOTICE
■When folding down the rear seatbacks
The seat belts and buckles must be stowed.
72
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory
Your preferred driving position (the position of the driver’s seat and
angle of the outside rear view mirrors) can be memorized and
recalled by pressing a button. It is also possible to set this function
to activate automatically when the doors are unlocked.
Two different driving positions can be entered into memory.
■ Entering a position to memory
STEP 1
Check that the shift lever is in P. Vehicles with smart key system: Turn the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: Turn the engine switch is in the “ON” position. Adjust the driver’s seat and outside rear view mirrors to the desired positions.
STEP 2
STEP 3
STEP 4
While pressing the “SET” but- ton, or within 3 seconds after the “SET” button is pressed, press button “1” or “2” until the signal beeps.
the selected button has If already been preset, the previ- ously recorded position will be overwritten.
: If equipped
73
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 2
■ Recalling the memorized position
Check that the shift lever is in P.
STEP 1
Vehicles with smart key system: Turn the “ENGINE START
STOP” switch is in IGNITION ON mode.
Vehicles without smart key system: Turn the engine switch
is in the “ON” position.
STEP 3
Press button “1” or “2” to recall the desired position.
74
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Power easy access system
The auto away/return function enables easy access by activat- ing when the driver attempts to enter or exit the vehicle.
Auto away function (exiting the vehicle) When all of the following actions have been performed, the seat will move backward: ● The shift lever has been shifted to “P”. ● Vehicles with smart key system: The “ENGINE START STOP”
switch has been turned off. Vehicles without smart key system: The key is removed from the engine switch.
● The driver’s seat belt has been unfastened. Auto return function (entering the vehicle) When either of the following actions has been performed, the seat will move forward: ● Vehicles with smart key system: The “ENGINE START STOP”
switch has been turned to ACCESSORY mode. Vehicles without smart key system: The engine switch has been turned to the “ACC” position.
● The driver’s seat belt has been fastened.
75
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Operating the driving position memory after turning the “ENGINE START STOP” switch off (vehicles with smart key system) or the key is removed from the engine switch (vehicle without smart key system) Memorized seat positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again.
■Stopping seat position recall operation part-way through
Perform any of the following operations: ●Press the “SET” button. ●Press button “1” or “2”. ●Adjust the seat using the switches.
■Correct seat position
When the seat is in the most forward or most backward position, and the seat is being moved in those directions, the system may not correctly recog- nize the current position and the memorized position will not be correctly recalled.
■The auto away function for exiting the driver’s seat
If the seat is already close to the rearmost position, the auto away function may not operate when the driver exits the vehicle.
■If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
■Customization
The auto away function for driver’s seat may be disabled. (Customizable features: P. 519)
76
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel.
77
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints
Head restraints are provided for all seats.
Front and rear outboard seats
Lock release button
Rear center seat (fabric seat)
Lock release button
Rear center seat (leather seat)
Lock release button
Vertical adjustment
Up Pull the head restraint up. Down Push the head restraints down while pressing the lock release button.
Vertical adjustment
Down Up Push the head restraint up or down while pressing the lock release button.
Vertical adjustment
Down Push the head restraint down while pressing the lock release button. Up Pull the head restraint up.
78
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Adjusting the height of the head restraints
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
■Adjusting the rear center seat head restraint
Always raise the head restraint one level from the stowed position when using.
■Removing the head restraints
Pull the head restraint up while pressing the lock release button.
■Installing the head restraints
Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
79
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure
they are locked in position.
●Do not drive with the head restraints removed.