1997 Toyota Supra Owners Manual

(cid:1) Headlights and turn signals (cid:1) Emergency flashers (cid:1) Instrument panel light control (cid:1) Front fog lights (cid:1) Interior lights (cid:1) Ignition switch light (cid:1) Luggage compartment light (cid:1) Windshield wipers and washer (cid:1) Rear window wiper and washer (cid:1) Rear window and outside rear

view mirror defoggers

Headlights and turn signals

To turn the lights on, twist the knob on the end of the lever. Daytime running light system (Canada only)—The headlights turn on when the parking brake is released with the engine started, even with the light switch in the “OFF” position. They will not go off until the ignition switch is turned off. The turn on the other exterior lights and in- strument panel lights, twist the knob to the first clickstop. Under the daytime running light system, the headlights turn on at reduced intensi- ty. Twist the knob to the second clickstop to turn to full intensity for driving at night.

FIRST CLICKSTOP: Only the parking, tail, license plate, side marker and instru- ment panel lights turn on. SECOND CLICKSTOP: The headlights also turn on. The lights automatically turn off when the driver’s door is opened with the ignition key turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off.

NOTICE

To prevent the battery from being discharged, do not leave the lights on for a long period when the engine is not running.

53

Emergency flashers

For high beam, push the lever away from you. Pull it toward you for low beam. For the headlight flasher, pull it further back. A blue light in the instrument panel indi- cates high beam is on. The headlight flasher works even when the headlight switch is off.

For signaling turns, move the lever up or down in the conventional manner. The key must be in the “ON” position. The turn signal is self–cancelling after a turn, but after a lane change, you may have to cancel it by hand. You can also signal a lane change by moving the turn signal lever partway and holding it there. If the green light in the instrument panel flashes faster than normal, it indicates that the front or rear turn signal bulb has burned out.

To turn on the emergency flashers, push the switch. All the turn signal lights will flash. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as possible. The turn signal light switch will not work when the emergency flashers are operat- ing.

54

Instrument panel light control

Front fog lights

NOTICE

To prevent the battery from being discharged, do not leave the lights on for a long period when the engine is not running.

To adjust the brightness of the instru- ment panel lights, turn the knob.

To turn on the front fog lights, twist the knob of the headlight and turn signal switch lever. They will come on when the headlights are turned on low beam.

55

Interior lights

Ignition switch light

Luggage compartment light

To turn on the interior light, slide the switch. With the central switch pushed on the “DOOR” side, both lights come on when either of the side doors is opened. The lights remain on for a certain time after both doors are closed.

For easy access to the ignition switch, the ignition switch light comes on when either side door is opened. The light remains on for a certain time af- ter both side doors are closed.

To turn the luggage compartment light on, open the back door and push the switch. Closing the back door will turn the light off.

56

Windshield wipers and washer

Rear window wiper and washer

If the washer does not work, check to see whether the washer tank is empty. For in- formation on adding washer fluid, see “Adding washer fluid” in Chapter 7–3. In cold weather, warm the windshield with the defroster before using the washer. This will help prevent icing, which could block your vision.

NOTICE

Do not operate the wipers if the windshield is dry. It may scratch the glass.

To turn the wipers on, move the lever. To make the washer squirt, push the button on the end of the lever. The key must be in the “ON” position. The wipers will operate at intervals when the lever is in the “INT” position. With the lever in this position, the wipers can be ad- justed to operate at intervals of 3 to 12 se- conds depending on the interval adjuster setting between “S” and “F”. If a single wipe is desired in mist, pull the lever toward you and release it. Also, the wipers will automatically operate a couple of times after the washer squirts even with the lever in the “OFF” position.

To turn the rear wiper and washer on, twist the knob at the end of the lever. The key must be in the “ON” position. The wiper will operate at intervals when the knob is in the “INT” position. The washer squirts at the two marked knob positions. The knob will automatical- ly return from these positions when it is re- leased. If the washer does not work, check to see whether the washer tank is empty. For in- formation on adding washer fluid, see “Adding washer fluid” in Chapter 7–3.

57

Make sure you turn the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop–and–go driving. The defoggers are not designed for drying rain water or for melting snow. If the outside rear view mirrors are heavily coated with ice, use a spray de–icer be- fore operating the switch.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires.

Rear window and outside rear view mirror defoggers

NOTICE

Do not operate the wipers if the windshield is dry. It may scratch the glass.

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the window surface. An indicator light will illuminate to indicate the defogger is operating. On some models, the heater panels in the outside rear view mirrors will also quickly clear the surfaces. Keep you hands off the mirror faces when the switch is on. Push the switch once again to turn the de- fogger off. The system will automatically shut off af- ter the defoggers have operated about 15
minutes.

58

Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—

Chapter 1–5
Gauges, Meters and Service reminder indicators (cid:1) Fuel gauge (cid:1) Engine coolant temperature

gauge

(cid:1) Tachometer (cid:1) Odometer and two trip meters (cid:1) Service reminder indicators

and warning buzzers

Fuel gauge

The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

The gauge works when the ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. It is a good idea to keep the tank over 1/4
full. This fuel gauge has a non–return type needle which remains at the last indicated position when the ignition switch is turned off. If the level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately.

59

Engine coolant temperature gauge

Tachometer

NOTICE

(cid:2)Do not remove the thermostat in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to control the flow of coolant to keep the temperature of the engine within the specified operating range.

(cid:2)Do not continue driving with an overheated engine. See “If your vehicle overheats” in Part 4.

tachometer

The indicates engine speed in thousands of rpm (revolu- tions per minute). Use it while driving to select correct shift points and to prevent engine lugging and overrev- ving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.

NOTICE

Do not let the indicator needle get into the red zone. This may cause severe engine damage.

The gauge indicates the engine cool- ant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle points to the red zone or high- er, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: (cid:1) Driving up a long hill on a hot day. (cid:1) Reducing speed or stopping after high

speed driving. Idling for a long period with the air con- ditioning on in stop–and–go traffic.

(cid:1)

60

Odometer and two trip meters

Service reminder indicators and warning buzzers

The meter display changes each time you push the “ODO TRIP” button, changing in order from the odomerter to rip meter A to trip meter B, then back to the odometer.

This meter displays the odometer and two trip meters. To change the odome- ter display to the trip meter display, push the “ODO TRIP” button. To reset the trip meter A to zero, display the me- ter A reading, then push the “RESET” button. The same applies for the trip meter B. The odometer records the total distance the vehicle has been driven. The trip me- ters can record two different distances in- dependently. You can use one trip meter to calculate the fuel economy and the other to measure the distance on each trip. All trip meter data is cancelled if the electrical power source is disconnected.

61

(a) Master Warning Light This light warns that another service re- minder indicator (except seat belt remind- er light, low fuel level warning lights, rear light failure warning light, SRS airbag warning light and “TRAC OFF” indicator/ warning light) is on. If it comes on while you are driving, check the other service reminder indicator that is on with reference to the following descrip- tion of the indicator. (b) Brake System Warning Light This light has the following functions: Parking brake reminder If this light is on, make sure the parking brake is fully released. The light should go off. Low brake fluid level warning If this light comes on and stays on while you are driving, slow down and pull off the road. Then stop the vehicle carefully. There maybe a problem somewhere in the brake system. Check the fluid level of the see–through reservoir. To make sure the parking brake has not caused the warning light to come on, check to see that the parking brake is fully released.

62

If the brake fluid level is low... At a safe place, test your brakes by start- ing and stopping. (cid:1)

If you judge that the brakes still work adequately, drive cautiously to your nearest dealer or shop for repairs. If the brakes are not working, have the vehicle towed in for repairs. (For tow- ing information, see Part 4.)

(cid:1)

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

If the brake fluid level is correct... Have the warning system checked by your Toyota dealer. (c) Seat Belt Reminder Light and Buzz-

er

Once the ignition key is turned to “ON” or “START”, the reminder light and buzzer come on if the driver’s seat belt is not fas- tened. Unless the driver fastens the belt, the light stays on and the buzzer stops af- ter about 4 to 8 seconds.

(d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- ate, however, until the battery is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.

NOTICE

Do not continue driving if the engine drive belt is broken or loose.

(e) Malfunction Indicator Lamp This lamp comes on in the following cases. a. The fuel tank is completely empty. (See “Fuel gauge” in Chapter 1–5 for in- structions.) b. There is a problem somewhere in your engine or automatic transmission electrical system. If it comes on while you are driving in case b, have your vehicle checked/repaired by your Toyota dealer as soon as possible.

(f) Low Fuel Pressure Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. (g) Low Oil Level Warning Light This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driv- ing, pull off the road to a safe place and stop the engine immediately. Call a Toyo- ta dealer or qualified repair shop for assis- tance. The light may occasionally flicker when the engine is idling or it may come on brief- ly after a hard stop. There is no cause for concern if it then goes out when the en- gine is accelerated slightly. The light may come on when the oil level is extremely low. It is not designed to indi- cate low oil level, and the oil level must be checked using the level dipstick.

NOTICE

Do not drive the vehicle with the warning light on—even for one block. It may ruin the engine.

63

(h) Low Engine Oil Level Warning

Light

The light warns that the engine oil level is too low. Add oil as soon as possible. (For instructions, see “Checking the engine oil level” in Chapter 7–2.)

NOTICE

Continued engine operation with low engine oil will damage the engine.

(i) “ABS” Warning Light This light warns that there is a problem somewhere in your anti–lock brake sys- tem. If the light comes on while you are driving, have your vehicle checked by your Toyota dealer as soon as possible. The light will come on when the ignition key is turned to the “ON” position. After about 3 seconds, the light will go off. When the “ABS” warning light is on (and the brake system warning light is off), the brake system operates conventionally but anti–lock brake system is not assisting brake performance so that the wheels can lock–up during sudden braking or braking on slippery road surfaces. 64

(j) Open Door Warning Light This light remains on until both side doors and back door are completely closed. (k) Rear Light Failure Warning Light If this light comes on when the headlight switch is turned on (at the first or second clickstop), it indicates that one or more of the tail lights are burned out. If it comes on when the brake pedal is de- pressed, one or more stop lights are burned out or the stop light circuit is in need of repair. Have defective bulbs replaced as soon as possible. (l) SRS Airbag Warning Light This light will come on when the igni- tion key is turned to the “ACC” or “ON” position. After about 6 seconds, the light will go off. This means the airbag system is operating properly. The warning light system monitors the air- bag sensors, center airbag sensor as- sembly, inflators, warning light, intercon- necting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle.

(cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position or remains on.

(cid:1) The light comes on while driving. (m) “TRAC OFF” Indicator/Warning

Light

This light comes on when the ignition key is turned to “N”, and will go off after 3 sec- onds. This means that the system is oper- ating properly. If one of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. (cid:1) The light remains on more than 3 sec- onds after the ignition switch is turned on.

(cid:1) The light comes on while driving even if the “TRAC OFF” switch is not pushed.

(cid:1) The light flashes. (n) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.

CHECKING SERVICE REMINDER INDI- CATORS (except the low fuel level warning light) 1. Apply the parking brake. 2. Open one of the side doors or the back

door. The open door warning light should come on.

3. Close the door.

The open door warning light should go off.

4. Turn the ignition key to “ACC”.

The SRS airbag warning light should come on. It goes off after about 6 sec- onds.

5. Turn the ignition key to “ON”, but do

not start the engine.

All the service reminder indicators except the open door warning light and SRS air- bag warning light should come on. The “ABS” warning light and “TRAC OFF” in- dicator/warning light go off after about 3
seconds. If any service reminder indicator or warn- ing buzzer does not function as described above, either the bulb is burned out or the circuit is in need of repair. Have it checked by your Toyota dealer as soon as pos- sible.

65

66

Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—

Chapter 1–6
Ignition switch, Transmission and Parking brake (cid:1) Ignition switch with steering lock (cid:1) Automatic transmission (cid:1) Manual transmission (cid:1) Parking brake (cid:1) Cruise control

Ignition switch with steering lock

“Start” – Starter motor on. The key will return to the “ON” position when re- leased. For starting tips, see Part 3. “ON” – Engine on and all accessories on. This is the normal driving position. “ACC” – Accessories such as the ra- dio operate, but the engine is off. If you leave the key in the “ACC” or “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK” – Engine is off and the steer- ing wheel is locked. The key can be re- moved only at this position.

You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be put in the “P” position before pushing the key. When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.

CAUTION

For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.

NOTICE

Do not leave the key in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.

67

Automatic transmission

When the cruise control is being used, even if you downshift the transmission by turning off the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this chapter. 68

Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Normal Driving 1. Start the engine as instructed in “How to start the engine” in Part 3. The trans- mission must be in “P” or “N”.

2. With your foot holding down the brake

pedal, shift the selector lever to “D”.

In “D” position, the automatic transmis- sion system will select the most suitable gear for running conditions such as nor- mal cruising, hill climbing, hard towing, etc. Always turn the overdrive switch on for better fuel economy and quieter driving. If the engine coolant temperature is low, the transmission will not shift into overdrive gear even with the overdrive switch on.

CAUTION

Never put your foot on the accelera- tor pedal while shifting.

3. Release the parking brake and brake pedal. Depress the accelerator pedal slowly for smooth starting.

(b) Using engine braking To use engine braking, you can downshift the transmission as follows: (cid:1) Turn off the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to the third gear.

(cid:1) Shift into the “2” position. The trans- mission will downshift to the second gear when the vehicle speed drops down to or lower than the following speed, and more powerful engine braking will be obtained. 2JZ–GE engine 115 km/h (72 mph) 2JZ–GTE engine 130 km/h (81 mph) (cid:1) Shift into the “L” position. The trans- mission will downshift to the first gear when the vehicle speed drops down to or lower than the following speed, and maximum engine braking will be ap- plied. 2JZ–GE engine 48 km/h (29 mph) 2JZ–GTE engine 60 km/h (37 mph)

When the cruise control is being used, even if you downshift the transmission by turning off the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this chapter.

CAUTION

Be careful when downshifting on a slippery surface. Abrupt shifting could cause the vehicle to spin or skid. (c) Using the “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in the first gear and automatically shift to the second gear. With the selector lever in “L”, the trans- mission is engaged in the first gear.

69

NOTICE

NOTICE

(cid:2)Be careful not to overrev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum allowable speed for each position is given below for your reference: 2JZ–GE “2” “L”

115 km/h (72 mph) 63 km/h (39 mph)

2JZ–GTE engine

“2” “L”

130 km/h (81 mph) 70 km/h (44 mph) (cid:2)Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmis- sion damage from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.

(d) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.

70

Never shift into reverse while the vehicle is moving.

(e) Parking 1. Bring the vehicle to a complete stop. 2. Pull the parking brake lever up fully to

securely apply the parking brake.

3. With the brake pedal pressed down, shift the selector lever to the “P” posi- tion.

CAUTION

While the vehicle is moving, never attempt to move the selector lever into “P” position under any circum- stances. Serious mechanical dam- age and loss of vehicle control may result.

(f) Good driving practice If the transmission is repeatedly upshifted and downshifted between third gear and overdrive when climbing a gentle slope, the overdrive switch should be turned off. Be sure to turn the switch on immediately afterward.

CAUTION

Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

NOTICE

Do not hold the vehicle on an upgrade with the accelerator pedal. It can cause the transmission to overheat. Always use the brake pedal or parking brake.

(g) Rocking your vehicle if stuck

CAUTION

If you rock your vehicle to make it out when it becomes stuck in snow, mud, sand, etc., first check that there is no physical object or people around the vehicle. During oper– ation the vehicle may suddenly move forward or backward, causing injury or damage to nearby people or objects.

NOTICE

If you rock your vehicle, observe the following precautions to prevent damage to the transmission and other parts. (cid:2)Do not depress the accelerator pedal while shifting the selector lever or before the transmission is completely shifted to forward or reverse gear.

(cid:2)Do not race the engine and avoid

spinning the wheels.

(cid:2)If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

(h) Driving in manual mode In the manual mode, the transmission system stops automatic gear shifting. Use this mode when starting your vehicle on a snowy or slippery road, when driving up steep inclines, and down with engine braking. To set the manual mode, push the “MANU” button. In the manual mode, the “MANU” mode indicator light comes on and the transmission shifts up or down as follows.

Manual transmission “D” position—The transmission is locked in third gear. When your vehicle speed drops down, the transmission will shift to second gear for smooth accelerating. “2” position—The transmission is locked in second gear. “L” position—The transmission is locked in first gear.

NOTICE

Be careful not to overrev the engine when using “2” or “L” position. If the automatic transmission fluid tem- perature becomes too high, the “MANU” mode indicator light flashes for several seconds and goes off. The driving mode then automatically changes from manual mode to the normal driving mode. To cancel the manual mode, push the “MANU” button once again. The “MANU” mode indicator light will go off and the transmission system will work in the nor- mal driving mode. The manual mode automatically cancels out when the ignition switch is off.

(i) If you cannot shift the selector lever

out of “P” position

If you cannot shift the selector lever from the “P” position even though the brake pedal is depressed, use the shift lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” in Part 4.

71

Manual transmission (5–speed)

The shift pattern is conventional as shown above. Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle when stopped on an uphill grade–use the parking brake.

72

Recommended shifting speeds The transmission is fully synchronized and upshifting or downshifting is easy. For the best compromise between fuel economy and vehicle performance, you should upshift or downshift at the follow- ing speeds:

Gear

km/h (mph)

24 (15) 40 (25) 64 (40) 72 (45)

1 to 2 or 2 to 1
2 to 3 or 3 to 2
3 to 4 or 4 to 3
4 to 5 or 5 to 4
Upshifting too soom or downshifting too late will cause lugging, and possibly ping- ing. Regularly revving the engine to mami- mum speed in each gear will cause exces- sive engine wear and high fuel consumption. Maximum allowable speeds To get on a highway or to pass slower traf- fic, maximum acceleration may be neces- sary. Make sure you observe the following maximum allowable speeds in each gear:

gear

km/h (mph) 54 (34) 94 (59) 139 (87)

NOTICE

Do not downshift if you are going faster than the maximum allowable speed for the next lower gear.

Good driving practice If it is difficult to shift into reverse, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

CAUTION

Be careful when downshifting on a slippery surface. Abrupt shifting could cause the vehicle to spin or skid.

NOTICE

Make sure the vehicle is complet– ely stopped before shifting into reverse.

Manual transmission (6–speed)

The shift pattern is shown above. You must lift up the ring around the gear shift lever to shift into “R” (reverse). Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle when stopped on an uphill grade–use the parking brake. Recommended shifting speeds The transmission is fully synchronized and upshifting or downshifting is easy. For the best compromise between fuel economy and vehicle performance, you should upshift or downshift at approxi- mately the following speeds:

gear

km/h (mph) 54 (34) 40 (25) 64 (40) 72 (45) 80 (50)

1 to 2 or 2 to 1
2 to 3 or 3 to 2
3 to 4 or 4 to 3
4 to 5 or 5 to 4
5 to 6 or 6 to 5
Upshifting too soon or downshifting too late will cause lugging, and possibly ping- ing. Regularly revving the engine to maxi- mum speed in each gear will cause exces- sive engine wear and high fuel consumption.

Maximum allowable speeds To get on a highway or to pass slower traf- fic, maximum acceleration may be neces- sary. Make sure you observe the following maximum allowable speeds in each gear:

gear

km/h (mph) 60 (38) 97 (61) 136 (85) 175 (109)

NOTICE

Do not downshift if you are going faster than the maximum allowable speed for the next lower gear.

Good driving practice If it is difficult to shift into reverse, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

73

CAUTION

Be careful when downshifting on a slippery surface. Abrupt shifting could cause the vehicle to spin or skid.

NOTICE

Make sure the vehicle is complete– ly stopped before shifting into reverse.

74

Parking brake

Cruise control

To set: Pull up the lever. To release: Pull up slightly, press the thumb button, and lower. Before leaving your vehicle, firmly apply the parking brake. For better holding pow- er, first depress the brake pedal and hold it while setting the parking brake.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

The cruise control allows you to cruise the vehicle at a desired speed over 40
km/h (25 mph)even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control

CAUTION

CAUTION

CAUTION

(cid:1) To help maintain maximum con- trol of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or in slip- pery (rainy, icy or snow–covered) or winding roads.

(cid:1) Avoid vehicle speed increases when driving downhill. If the ve- hicle speed is too fast in relation to the cruise control set speed, can- cel the cruise control then down- shift the transmission to use en- gine braking to slow down.

TURNING ON THE SYSTEM To operate the cruise control, push the “CRUISE ON–OFF” switch. This turns the system on. The indicator light in the instru- ment panel shows that you can now set the vehicle at a desired cruising speed. Another push will turn the system com- pletely off.

To avoid accidental cruise control engagement, keep the “CRUISE ON–OFF” switch off when not using the cruise control.

SETTING AT A DESIRED SPEED On vehicles with automatic transmission, the transmission must be in “D” before you set the cruise control speed. Bring your vehicle to the desired speed, push the lever down in the “SET/COAST” direction and release it. This sets the ve- hicle at that speed. If the speed is not sat- isfactory, tap it down for a slower speed. Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your foot off the accelerator pedal. If you need acceleration — for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the ve- hicle will return to the speed set prior to the acceleration.

For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overreving.

CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di- rection and releasing it. b. Depressing the brake pedal. c. Depressing the clutch pedal (manual transmission). If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out. If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset speed will also automatically cancel out. If the preset speed automatically cancels out other than for the above cases have your vehicle checked by your Toyota deal- er at the earliest opportunity.

75

RESETTING AT A FASTER SPEED Press the control lever upward in the “RES/ACC” direction and hold it. Release the lever when the desired speed is at- tained. While the lever is held up, the ve- hicle will gradually gain speed. However, a faster way to reset is to accel- erate the vehicle and then push the lever down in the “SET/COAST” direction. RESETTING AT A SLOWER SPEED Push the control lever down in the “SET/ COAST” direction and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “SET/COAST” direction.

RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control lever or by depressing the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARN- ING If the “CRUISE” indicator light in the in- strument cluster flashes when using the cruise control, press the “CRUISE ON– OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. (cid:1) The indicator light does not come on. (cid:1) The indicator light flashes again. (cid:1) The indicator light goes out after it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

76

Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—

(cid:5) Instrument panel vents

Car audio system— —Reference

Chapter 1–7
Car audio system and Air conditioning system Car audio system (cid:5) Reference (cid:5) Using your audio system:

some basics

(cid:5) Using your audio system:

controls and features

(cid:5) Anti–theft system (cid:5) Car audio system operating

hints

Air conditioning system (cid:5) Controls (cid:5) Air flow selector settings (cid:5) Operating tips

Type 1–1: AM·FM ETR radio/cassette player

Type 1–2: AM⋅FM ETR radio/cassette player

77

—Using your audio system: some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the igni- tion key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR ⋅ VOL” or “PWR/VOL” to turn the audio system on and off. Push “AM ⋅ FM”, “TAPE” or “CD” to turn on that function without pushing “PWR ⋅ VOL” or “PWR/VOL”. You can turn on the cassette player by in- serting a cassette tape. You can turn off the cassette player by ejecting the cassette tape. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape. If the radio was previously on, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM ⋅ FM”, “TAPE” or “CD” if the sys- tem is already on but you want to switch from one function to another.

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal pro- grams usually sound better with different mixes of treble, midrange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

Type 1–3: AM·FM ETR radio/cassette player

Type 2: AM⋅FM ETR radio/cassette player/compact disc player 78

YOUR RADIO ANTENNA To lower a manual antenna, carefully push it down. To lower a power antenna, turn off the au- dio system by pushing “PWR ⋅ VOL” or “PWR/VOL”, or turn the ignition key to “LOCK”. On some models, the power antenna au- tomatically retracts when the radio mode is switched off to turn on the cassette tape player or compact disc player.

NOTICE

To prevent damage to the antenna, make sure it is retracted before driving your Toyota through an automatic car wash.

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cassette tapes into the slot, or the tape player may be damaged.

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will au- tomatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

8 cm (3 in.) compact disc singles Your compact disc player does not need an adaptor to play compact disc singles. Compact disc singles are about 8 cm (3
in.) in diameter–smaller than standard discs. After you eject a compact disc single, do not insert a standard 12 cm (5 in.) disc un- til “DISC” disappears from the display.

NOTICE

Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs.

79

—Using your audio system: controls and features (cid:1)Type 1–1

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

80

(cid:1)Type 1–2

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

81

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

(cid:1)Type 1–3

82

1 2 3 4 5 6 (Preset buttons) These buttons are used to preset and tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” or “TUNE/ SEEK”). Push and hold down the button until you hear a beep–this will set the sta- tion to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The button number and station frequency will appear on the display. Type 1–1 and 1–2—These systems can store one AM and one FM station for each button. The preset station memory will be canceled out if the power source is inter- rupted (battery disconnected or fuse blown). Type 1–3—These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1”, or “FM2” when you push “AM ⋅ FM”.) To can- cel out the preset station memory, push “1”, “2”, and “3” at the same time and hold them in until you hear a beep.

/EJECT (Eject button)

Push this button to eject a cassette. After you turn the ignition to “LOCK”, you will be able to eject a cassette but you will not be able to reinsert it. AM ⋅ FM Push “AM ⋅ FM” to switch between the AM and FM bands. Type 1–1 and 1–2—”AM” or “FM” will ap- pear on the display. Type 1–3—”AM”, “FM1” or “FM2” will ap- pear on the display. If the audio system is off, you can turn on the radio by pushing “AM ⋅ FM”. Also, push “AM⋅FM” to switch from cassette op- eration to radio operation. APS (Automatic program selection) Type 1–3 only The automatic program selection (APS) feature allows you to program your cas- sette player to skip forward or backward to locate the song you want to hear. You can skip up to nine tracks at a time. Push “APS”. “APS” and “1” will appear on the display.

Next, push “APS” until the number on the display reaches the number of tracks you want to skip. If you push “APS” ten times, the APS feature will be turned off. (cid:5)

If you choose the number “1”, the play- er will rewind to the beginning of the current track.

(cid:5) When counting the number of tracks you want to rewind, remember to count the current track as well. For ex- ample, if you want to rewind to a song that is two before the song you are lis- tening to, push “APS” until “3” appears on the display.

Finally, push “REW” or “FF” to choose the direction you want to skip. The player will rewind or fast forward the selected num- ber of tracks and play. The APS number you select can be higher than the number of tracks remaining on the current cassette side. After the begin- ning or end of the tape is reached, the player will automatically reverse sides and rewind or fast forward the additional number of tracks.

83

There must be at least 3 seconds of blank space between tracks in order for the APS feature to work correctly. In addition, the APS feature may not work well with some spoken word, live, or classical recordings. BAL (Balance) This knob lets you adjust the balance be- tween the right and left speakers. BASS This knob lets you adjust the bass level. Push “BASS/TREB” so that it pops out of its retracted position. Turn the knob to ad- just the bass. Push the knob back into its retracted position. Dolby Type 1–1 and 1–2 only If you are listening to a tape that was re- corded with Dolby Noise Reduction, push the double–D symbol. The double–D symbol will appear on the display. Push the button again to turn off Dolby NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for record- ing the tape.

the button marked with

NR*

84

*: Dolby noise reduction manufactured under license from Dolby Lab- oratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.

B ⋅ C*

Dolby Type 1–3 only If you are listening to a tape that was re- corded with Dolby B or C Noise Reduc- tion, push the button marked with the double–D symbol until the appropriate symbol appears on the display. To turn off Dolby, push the button until the symbol disappears from the display. The Dolby B NR mode reduces tape noise by about 10dB. The Dolby C NR mode re- duces tape noise by another 10 dB, or about 20 dB total. For best sound repro- duction, select the same NR mode that was used to record the tape. *: Dolby noise reduction manufactured under license from Dolby Lab- oratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FADE Move the “FADE” ring around “PWR/ VOL” to adjust the front/rear balance.

MTL (Metal) display Type 1–3 only If a metal or chrome equivalent cassette tape is put in the cassette player, the play- er will automatically adapt to it and “MTL” will appear on the display. PROG (Program) Type 1–2 and 1–3 only push “PROG” to select the other side of a cassette tape. The display indicates which side is currently selected (“∧” indicates top side, “∨” indicates bottom side). Auto–reverse feature—After the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding. PWR/VOL (Power/Volume) Push “PWR/VOL” to turn the audio sys- tem on and off. Turn the “PWR/VOL” knob to adjust the volume. Pull out and then turn “PWR/VOL” to ad- just the balance between the right and left speakers. Move “FADE” around “PWR/ VOL” to adjust the front/rear balance.

REW/FF (Rewind/Fast forward) Push the “FF” side of the button to fast for- ward a cassette tape. “FF” will appear on the display. Push the “REW” side to re- wind a tape. “REW” will appear on the dis- play. To stop the tape while it is fast forwarding, push “FF” or “TAPE”; to stop the tape while it is rewinding, push “REW” or “TAPE”. The tape will immediately begin to play. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette palyer will play the other side of the tape, using the auto–re- verse feature. R.M (Radio monitor) Type 1–3 only The radio monitor feature allows you to listen to the radio while a cassette is being rewound or fast forwarded. Push “R ⋅ M”. “R ⋅ M” will appear on the dis- play. Any time you are rewinding or fast forwarding a cassette tape, the radio will play the station that was set most recent- ly. (You can not change the radio station unless you switch out of the cassette play- er function.)

Push “R ⋅ M” again to turn off the R’M fea- ture. RPT (Repeat) Type 1–3 only The repeat feature automatically replays the current cassette. Push “RPT” while the track is playing. “RPT” will appear on the display. When the track ends, it will automatically be re- wound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. SCAN Type 1–2 and 1–3 only You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan all the frequencies. The radio will tune in the next preset station up the band, stay there for a few seconds, and the move to the next preset station. To se- lect a station, push “SCAN” a second time.

To scan all the frequencies: Push “SCAN” until you hear a beep. The radio will find the next station up the station band, stay there for a few seconds, and then scan again. To select a station, push “SCAN” a second time. Cassette Player Type 1–3 only The cassette player scan feature is similar to the radio scan feature and uses the same button. Push “SCAN”. “SCAN” will appear on the display. The player will fast forward to the next cassette track, play it for 12 seconds, and then scan again. To select a track, push “SCAN” a second time. If the player reaches the end of one side of a cassette tape, it will continue scanning on the other side. SKIP Type 1–3 only The skip feature allows you to fast forward past long stretches of blank tape. This is especially useful at the end of cassettes.

85

Push “SKIP”. “SKIP” will appear on the display. The cassette player will keep track of how much blank space it plays. Any time it has played about 10 seconds of blank tape, it will automatically fast for- ward to the next track and begin to play. Push the button a second time to turn off the skip feature. ST (Stereo reception) display Your radio automatically changes to ste- reo reception when a stereo broadcast is received. “ST” appears on the display. If the signal becomes weak, the radio re- duces the amount of channel separation to prevent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono reception. TAPE Push “TAPE” to switch from radio opera- tion to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. If both cases, a cassette must already be loaded in the player.

TREB (Treble) This knob lets you adjust the treble level. Push “BASS/TREB” so that it pops out of its retracted position. Pull out the knob. Turn the knob to adjust the treble. Push the knob back into its retracted position. TUNE/SEEK Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “∧” (up) or “∨” (down) side of “TUNE/SEEK” to step up or down the station band. If you hear a beep, you held the button too long and the radio will go into the seek mode. Seeking In the seak mode, the radio finds and plays the next station up or down the sta- tion band. To seek a station, push and hold the “∧” or “∨” side of “TUNE/SEEK” until you hear a beep. Do this again to find another station.

86

(cid:1)Type 2

Button display for radio/cassette tape player/compact disc player

87

Your audio system shows there different button displays that changes in accor- dance with the audio mode you have se- lected. Radio display (display 1) Cassette player display (display 2) Compact disc player display (display 3) Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

1 2 3 4 5 6 (Press buttons) These buttons are used to preset and tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” button). Push and hold down the button until you hear a beep–this will set the station to the button. The button number will appear on the display. To tune in to a preset station: Push the button for the station you want. The button number and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1”, or “FM2” when you push “AM ⋅ FM”) To cancel out the preset station memory, push “1”, “2”, and “3” at the same time and hold them in until you hear a beep.

(Eject Button)

Push the cassette tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it. I(cid:2)(cid:2)/(cid:4)(cid:1)(cid:1)I (Track down/up button) By using this button, you can skip up or down to a different track. Cassette Player You can skip up to nine tracks at a time. Push the up or down side of the button. “1. FF” or “1. REW” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two before the song you are listening to, push on the down side of the button until “3. REW” ap- pears on the display.

88

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be re- duced. The track number you select is not valid if it is higher than the number of tracks re- maining on the current cassette side. (cid:5) After the beginning of the tape is reached, the player will automatically start playing the same side.

(cid:5) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. Compact Disc Player Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the beginning of the current track, push the down side of the button one time, quickly.

(cid:2)(cid:2)/(cid:1)(cid:1) (Reverse/Fast forward but- tons) Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to re- wind a tape. “REW” will appear on the dis- play. To stop the tape while it is fast forwarding, push on the up side of the track down/up button or “TAPE”’; to stop the tape while it is rewinding, push on the down side of the track down/up button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto–re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the com- pact disc player will resume playing.

AM ⋅ FM Push “AM⋅FM” to switch between the AM and FM bands. “AM”, “FM1” or “FM2” will appear on the display. These systems al- low you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “AM ⋅ FM”. Also, push “AM ⋅ FM” to switch from cassette or compact disc operation to radio opera- tion. BALL (Balance) This knob lets you adjust the balance be- tween the right and left speakers. Push “MID/BAL” so that it pops out of its retracted position. Pull out the knob. Turn the knob to adjust the balance. Push the knob back into its retracted position. BASS This knob lets you adjust the bass level. Push “BASS” so that it pops out of its re- tracted position. Turn the knob to adjust the bass. Push the knob back into its re- tracted position.

89

The Dolby B NR mode reduces tape noise by about 10 dB. The Dolby C NR mode re- duces tape noise by another 10 dB, or about 20 dB total. For best sound repro- duction, select the same NR mode that was used to record the tape. *: Dolby noise reduction manufactured under license from Dolby Lab- oratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.

CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track number currently being played. Pushing “CD” changes the display to show the length of the current program being played so far. By pushing the button once again, the display returns to that of track number. Dolby B ⋅ C * If you are listening to a tape that was re- corded with Dolby B or C Noise Reduc- tion, push the button by the double–D symbol until the appropriate symbol ap- pears on the display. To turn off Dolby  push the button until the symbol disap- pears from the display.

90

Five EQ settings

EQ (Equalizer) Your audio system can store five different EQ settings in its memory so that you will not need to readjust it every time you lis- ten to a different program. Five common settings are stored in the system’s memory when it is manufac- tured (see illustration). To use a preset EQ setting: Push “EQ”. The levers for the first setting and “EQ–1” will appear on the display. Push “EQ” until you reach the setting you want. The audio system will adjust the program you are hearing to the selected setting. To change a preset EQ setting: Push “EQ” until the setting you want to change ap- pears on the display. Adjust the bass, mid–range, and treble level using the “BASS”, “MID/BAL”, and “TREB/FADE.” To save an EQ setting: After you have changed a setting, push “EQ” until you hear a beep. This will replace the original factory setting with your new one. To cancel one of the EQ settings you saved: With the setting on the display, push in and hold “EQ” until you have heard both the first “save” beep and a sec- ond beep that means the setting has been canceled. The original factory setting will appear on the display.

To cancel all of the changed EQ settings: Push and hold in”EQ” until you hear a third beep. FADE This knob lets you adjust the balance be- tween the front and rear speakers. Push “TREB/FADE” so that it pops out of its retracted position. Pull out the knob. Turn the knob to adjust the front/rear bal- ance. Push the knob back into its re- tracted position. MID (Mid–range) This knob lets you adjust the mid–range level. Push “MID/BAL” knob so that it pops out of its retracted position. Turn the knob to adjust the mid–range level. Push the knob back into its retracted position. MTL (Metal) Display If a metal or chrome equivalent cassette tape is put in the cassette player, the play- er will automatically adapt to it and “MTL” will appear on the display.

PROG (Program) Push “PROG” to select the other side of a cassette tape. The display indicates which side is currently selected (“∧” indi- cates top side, “v” indicates bottom side). Auto–reverse feature: After the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding. PWR/VOL (Power/Volume) Push “PWR/VOL” to turn the audio sys- tem on and off. Turn “PWR/VOL” to adjust the volume. RAND (Random) The random feature allows you to listen to the tracks on a compact disc in random or- der. When you push “RAND”, “RAND” will ap- pear on the display and the player will play the tracks in random order. Push the but- ton again to turn off the random feature.

91

RM (Radio Monitor) The radio monitor feature allows you to listen to the radio while a cassette is being rewound or fast forwarded. Push “RM”. “RM” will appear on the dis- play. Any time you are rewinding or fast forwarding a cassette tape, the radio will play the station that was set most recent- ly. (You can not change the radio station unless you switch out of the cassette play- er function.) Push “RM” again to turn off the RM fea- ture. RPT (Repeat) The repeat feature automatically replays the current cassette or compact disc track. Push “RPT” while the track is playing. “RPT” will appear on the display. When the track ends, it will automatically be re- wound (cassette) and replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Cassettes—There must be at least 3 sec- onds of blank space between tracks in or- der for the repeat feature to work correct- ly.

92

Scan Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Quickly push and release “SCAN.” If you hear a beep, you held the button too long, and the radio will scan all the frequencies. The radio will tune in the next preset station up the band, stay there for a few seconds, and then move to the next preset station. To select a station, push “SCAN” a second time. To scan all the frequencies: Push “SCAN” until you hear a beep. The radio will find the next station up the station band, stay there for a few seconds, and then scan again. To select a station, push “SCAN” a second time. Cassette Player The cassette player scan feature is similar to the radio scan feature and uses the same button.

Push “SCAN”. “SCAN” will appear on the display. The player will fast forward to the next cassette track, play it for 12 seconds, and then scan again. To select a track, push “SCAN” a second time. If the player reaches the end of one side of a cassette tape, it will continue scanning on the other side. Compact disc player The compact disc player scan feature is similar to the radio scan feature. Push “SCAN”. “SCAN” will appear on the display. The compact disc player will play the next track for 10 seconds, then scan again. To select a track, push “SCAN” a second time. If the player reaches the end of the disc, it will continue scanning at track 1. SKIP The skip feature allows you to fast forward past long stretches of blank tape. This is especially useful at the end of cassettes.

Push “SKIP”. “SKIP” will appear on the display. The cassette player will keep track of how much blank space it plays. Any time it has played about 10 seconds of blank tape, it will automatically fast for- ward to the next track and begin to play. Push the button a second time to turn off the skip feature. ST (Stereo reception) display Your radio automatically changes to ste- reo reception when a stereo broadcast is received. “ST” appears on the display. If the signal becomes weak, the radio re- duces the amount of channel separation to prevent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono reception. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.

TREB (Treble) This knob lets you adjust the treble level. Push “TREB/BASS” so that it pops out of its retracted position. Turn the knob to ad- just the treble. Push the knob back into its retracted position. TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “∧” (up) or “v” (down) side of “TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.) Seeking In the seek mode, the radio finds and plays the next station up or down the sta- tion band. To seek a station, push and hold the “^” or “v” side of “TUNE” until you hear a beep. Do this again to find another station.

—Anti–theft system (type 1–3 and 2 only) The anti–theft system prevents the audio system from working after it has been dis- connected. To activate the system, you must set a three–digit security code. After the system is set, “SEC” will appear in the display each time the ignition is turned form “LOCK” or “ACC” or “ON”. Also, the anti–theft light flashes every few seconds while the ignition key is in the “LOCK” position. You will need to know your security code to reactivate your radio after electrical ser- vice is performed on your vehicle. Choose a security code that is easy to re- member and keep a copy of it (not in your Toyota).

NOTICE

If you pushed any wrong buttons on the anti–theft system, the following messages will appear on the display. (cid:7)“Err”—You have pushed wrong

buttons.

93

(cid:7)“1–9”—Indicates the number of er- rors you have made. You may make up to nine errors, but no more!

(cid:7)“HELP”—The number of error you can make was exceeded. The audio sytem is completely inoperable. Contact you Toyota dealer.

94

Setting a security code for the first time. 1. Turn off the audio system. Turn the ignition key to “ACC”. Simultaneously push and hold in “1”, “6”, and “PWR/VOL” until “SEC” appears on the display.

2. While you are holding in the “^” side of

“TUNE”, push “1”.

The display will read “—“. On some modes, “(cid:3)” and “(cid:6)” will also turn on.

Input the three digit code.

3. You have 10 seconds to enter each digit. For example, “209”: To set the first digit: Push “1” until the digit you want appears on the display. To set the second digit: Push “2” until the digit you want appears on the display. To set the third digit: Push “3” until the digit you want appears on the display.

4. The three–digit code should be on the

display.

Push and hold in “SCAN” until the display goes dark. (At first, “SEC” will appear on the display.)

If you pushed any wrong buttons, “Err” and the number of errors you have made will appear on the display before “SEC” does. Go back to step 2
and try again. If the display returns to “—“ while you are entering the code, go back to step 3. To make sure the security code has been accepted, turn the ignition to “LOCK” and then back to “ACC.” “SEC” should appear on the display. Choose a security code that is easy to re- member and keep a copy of it (not in your Toyota).

95

Changing the security code 1. Turn off the audio system. Turn the ignition key to “ACC”. Simultaneously push and hold in “1”, “6”, and “PWR/VOL” until “SEC” appears on the display.

2. While you are holding in the “^” side of

“TUNE” push “1”.

The display will read “—”. On some models, “ (cid:3)” and “(cid:6)” will also turn on.

Input the existing three–digit code.

3. You have 10 seconds to enter each digit. For example, “209”: To set the first digit: Push “1” until the digit you want appears on the display. To set the second digit: Push “2” until the digit you want appears on the display. To set the third digit: Push “3” until the digit you want appears on the display.

96

4. The three–digit code should be on the

display.

Push “SCAN”. 5. Repeat steps 2 and 3, this time enter- ing your new code. You can use digits “0” through “9”.

6. The new three–digit code should be on

the display.

Push and hold in “SCAN” until the display goes dark. (At first, “SEC” will appear on the display.)

If you pushed any wrong buttons, “Err” and the number of errors you have made will appear on the display before “SEC” does. Go back to step 2
and try again. If the display returns to “—“ while you are entering the code, go back to step 3. To make sure the security code has been accepted, turn the ignition to “LOCK” and then back to “ACC”. “SEC” should appear on the display.

NOTICE

A tenth error will activate the anti–theft system and “HELP” will appear on the display. The audio system will be completely inoperable. At this time, the anti–theft light also comes on. If this occurs, contact your Toyota dealer.

97

Cleaning the security code. 1. Turn off the audio system. Turn the ignition key to “ACC”. Simultaneously push and hold in “1”, “6”, and “PWR/VOL” until “SEC” appears on the display.

2. While you are holding in the “∧” side of

“TUNE”, push “1”.

The display will read “—“. On some models, “(cid:3)” and “(cid:6)” will also turn on.

Input the existing three–digit code.

3. You have 10 seconds to enter each digit. For example, “209”: To set the first digit: Push “1” until the digit you want appears on the display. To set the second digit: Push “2” until the digit you want appears on the display. To set the third digit: Push “3” until the digit you want appears on the display.

98

If you pushed any wrong buttons, “Err” and the number of errors you have made will appear on the display before “SEC” does. Go back to step 2
and try again. If the display returns to “–––“ while you are entering the code, go back to step 3.

NOTICE

A tenth error will activate the anti–theft system and “HELP” will appear on the display. The audio system will be completely inoperable. At this time, the anti–theft light also comes on. If this occurs, contact your Toyota dealer.

4. The three–digit code should be on the

display.

Push “SCAN”. The display will read “–––“. 5. Wait for 10 seconds until the security system is deactivated and the display goes dark.

Reactivating a disabled audio system 1. Turn the ignition switch to “ACC”. 2. While you are holding in the “∧” side of

“TUNE”, push “1”.

The dispay will read “–––”. On some models, “(cid:3)” and “(cid:6)” will also turn on.

99

If you pushed any wrong buttons, “Err” and the number of errors you have made will appear on the display before “SEC” does. Go back to step 2
and try again. If the display returns to “–––“ while you are entering the code, go back to step 3. To make sure the security code has been accepted, turn the ignition to “LOCK” and then back to “ACC”. “SEC” should appear on the display.

NOTICE

A tenth error will activate the anti–theft system and “HELP” will appear on the display. The audio system will be completely inoperable. At this time, the anti–theft light also comes on. If this occurs, contact your Toyota dealer.

Input the existing three–digit code.

3. You have 10 seconds to enter each digit. For example, “209”: To set the first digit: Push “1” until the digit you want appears on the display. To set the second digit: Push “2” until the digit you want appears on the display. To set the third digit: Push “3” until the digit you want appears on the display.

4. The three–digit code should be on the

display.