scopic steering) Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (P. 79)
165
2-2. Instrument cluster Gauges and meters
Vehicles with multi-information display
The following gauges, meters and displays illuminate when the engine switch is in the ON position.
Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Voltmeter Displays the charge state. Engine oil pressure gauge Displays the engine oil pressure. Engine coolant temperature gauge Displays the engine coolant temperature. Odometer/trip meter switching and trip meter resetting button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played.
166
2-2. Instrument cluster
Multi-information display
P. 176
Automatic transmission fluid temperature gauge
Displays the automatic transmission fluid temperature.
167
2-2. Instrument cluster
Vehicles without multi-information display
The following gauges, meters and displays illuminate when the engine switch is in the ON position.
Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Voltmeter Displays the charge state. Engine oil pressure gauge Displays the engine oil pressure. Engine coolant temperature gauge Displays the engine coolant temperature. Odometer/trip meter switching and trip meter resetting button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played.
168
2-2. Instrument cluster
Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently. Automatic transmission fluid temperature gauge (if equipped) Displays the automatic transmission fluid temperature.
Odometer and trip meter display button
Pressing this button switches between odometer and trip meter dis- plays.
Vehicles with multi-information display
Odometer Trip meter A* Trip meter B* *: Pushing and holding the button
will reset the trip meter.
Vehicles without multi-information display
Odometer Trip meter A* Trip meter B* *: Pushing and holding the button
will reset the trip meter.
169
2-2. Instrument cluster
Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Brighter Darker
Vehicles with multi-information display
With the dial turned fully up, the intensity of the instrument panel lights will not be reduced even when the tail lights/headlights are turned on.
NOTICE
■To prevent damage to the engine and its components
●Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (P. 592)
■While driving
●When the voltmeter indicates more than 19 V or less than 9 V, the battery may be malfunctioning. Have your vehicle checked at your Toyota dealer. ●When the engine oil pressure gauge does not work properly, immediately
stop the engine and contact your Toyota dealer.
●When the automatic transmission fluid temperature gauge needle continu- ally points higher than normal, immediately contact your Toyota dealer. (if equipped)
170
2-2. Instrument cluster Indicators and warning lights
The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.
Instrument cluster (vehicles with multi-information display)
Instrument cluster (vehicles without multi-information display)
171
2-2. Instrument cluster
Center panel
Outside rear view mirrors [vehicles with BSM (Blind Spot Moni- tor)]
172
2-2. Instrument cluster
■ Indicators
The indicators inform the driver of the operating state of the vehicle’s various systems.
Turn signal indicator (P. 163)
Headlight high beam indicator (P. 189) Security indicator
(P. 104, 106)
Shift position and shift range indicators (P. 159)
Cruise control indicator (P. 200, 204)
*1,4
Slip indicator (P. 254, 256)
*1 VSC OFF indicator (P. 253, 256, 258, 259)
*6
(If equipped)
BSM outside rear view mirror indicators (P. 236)
Headlight indicator (P. 185)
(U.S.A.)
(Canada)
*1
(4WD models)
*1
*1
*1
(4WD models)
(4WD models)
(If equipped)
Tail light indicator (P. 185)
AUTO LSD indicator (P. 253, 256)
Center differential lock indicator (P. 249)
TRAC OFF indicator (P. 256, 258, 259)
AIR BAG ON indicator (P. 123)
AIR BAG OFF indicator (P. 123)
4HI indicator (P. 248)
4LO indicator (P. 248)
TOW HAUL indicator (P. 161)
173
2-2. Instrument cluster
*1,2
*1,2
Height control HI indi- cator (P. 242)
Height control N indi- cator (P. 242)
*1,2
*1,2
Height control MAN. indicator (P. 243)
Height control LO indi- cator (P. 242)
■ Warning lights
Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (P. 557)
*1
*1
*2
*1
*1
*1
*1
*1
*1
*1
*1
(U.S.A.)
(Canada)
(U.S.A.)
*3
(Canada)
*1,3
(U.S.A.)
(U.S.A.)
(Canada)
*3
*1,5
*1: These lights turn on when the engine switch is turned to the ON position to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.
*2: Vehicles with multi-information display *3: Vehicles without multi-information display *4: The indicator flashes to indicate that the system is operating. *5: The indicator comes on to indicate a malfunction.
174
2
2-2. Instrument cluster
*6: In order to confirm operation, the BSM outside rear view mirror indi-
cators illuminate in the following situations: • When the engine switch is turned to the ON position while the
BSM main switch is set to ON.
• When the BSM main switch is set to ON while the engine switch is
in the ON position.
If the system is functioning correctly, the BSM outside rear view mirror indicators will turn off after a few seconds. If the BSM outside rear view mirror indicators do not illuminate or do not turn off, there may be a malfunction with the system. If this occurs, have the vehicle inspected by your Toyota dealer.
CAUTION
■If a safety system warning light does not come on
Should a safety system light such as ABS and the SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.
175
2-2. Instrument cluster Multi-information display
The multi-information display presents the driver with a variety of driving-related data.
● Trip information
(P. 176) Displays driving range, fuel consumption and other cruis- ing-related information.
● Warning messages
(P. 568) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.
● Odometer and trip meter (P. 169)
display
Trip information
Display items can be switched by pushing the INFO button.
176
: If equipped
2-2. Instrument cluster
Zoom display of odometer and trip meters
Displays the odometer and one of the trip meters simultaneously.
Average Fuel Economy
Displays the average fuel consumption since the function was reset.
● The function can be reset by pushing the SELECT RESET button for more than 2 seconds when the Average Fuel Economy is displayed.
● Use the displayed average fuel consumption as a
reference.
Current Fuel Economy
Displays the current rate of fuel consumption.
Distance To Empty (driving range)
Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. ● This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
● When only a small amount of fuel is added to the
tank, the display may not be updated.
177
2-2. Instrument cluster
Trip Timer
Average Speed
Displays the driving time.
To calculate the driving time, press the SELECT RESET button, and to stop the calculation, press it again. To reset the calculation, press the SELECT RESET button for more than 2 seconds.
Displays the average vehicle speed since the engine was started or the function was reset.
The function can be reset by pushing the SELECT RESET button for more than 2 seconds when the Average Speed is displayed.
178
2
2-2. Instrument cluster
Feature customization
The vehicle can be customized while the vehicle is stopped.
Press the SETUP button to select the item you want to cus- tomize unit. UNITS
KEYLESS ENTRY FEEDBACK
KEYLESS ENTRY RELOCK TIMER
KEYLESS ENTRY ALL DOORS UNLOCK
DOOR AUTO LOCKING
DOOR AUTO UNLOCKING
HEADLAMPS AUTO OFF TIMER
COURTESY LAMPS OFF TIMER
LANGUAGE
DEFAULT SETTING Press the SELECT RESET button to customize the items.
Items
Screen text
Select in this order
To select Unit A or Unit B (P. 184)
Door lock/ unlock warning function
Time for auto- matic door lock function
UNITS
Unit A
Unit B
KEYLESS ENTRY FEEDBACK
KEYLESS ENTRY RELOCK TIMER
LAMPS + TONE*
LAMPS
OFF
TONE
60 SECONDS*
120 SECONDS
30 SECONDS
OFF
179
2-2. Instrument cluster
Items
Screen text
Select in this order
Double switch operation to unlock all the doors
KEYLESS ENTRY ALL DOORS UNLOCK
Automatic door locking function
DOOR AUTO LOCKING
DOOR AUTO UNLOCKING
2 PRESSES*
1 PRESS
SHIFT OUT OF PARK
ABOVE 12 MPH* (20 km/h)
OFF
SHIFT TO PARK*
DRIVER DOOR OPEN
OFF
30 SECONDS*
60 SECONDS
HEADLAMPS AUTO OFF TIMER
0 SECONDS
90 SECONDS
Automatic door unlocking func- tion Time period before lights turn off (if a door is opened and closed, and engine switch is in ACC or LOCK) Time period before lights turn off
15 SECONDS*
30 SECONDS
8 SECONDS
ENGLISH*
FRENCH
SPANISH
COURTESY LAMPS OFF TIMER
Selecting the language
LANGUAGE
Reset to default setting *: Default setting
HOLD RESET TO RESTORE DEFAULT SETTINGS
After customize is complete, press the SETUP button to set the selected item. If the customization fails, the previously setting will be displayed. If no button is pressed for 10 seconds, the display change to normal display.
180
2-2. Instrument cluster
■To select the unit A (English/U.S. customary system) or unit B (metric
unit)
Press the SETUP button to display UNITS on the multi-information display. Press the SELECT RESET button to change the units. Press the INFO or SETUP button and complete the unit change.
Information
Average Fuel Economy and Current Fuel Economy Driving Range Average Speed Outside temperature display on the accessory meter
■Feature customization error
Unit A
MPG
MILES MPH
°F
Unit B
L/100 Km
Km Km/h
°C
• If SYSTEM ERROR message is indicated, turn the engine switch off and
• If SYSTEM ERROR message is indicated again, contact your Toyota
then on again.
dealer.
CAUTION
■Caution while driving
Do not adjust the display. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.
181
2-2. Instrument cluster Accessory meter
Outside temperature display Displays the outside air temperature. (P. 434) Outside temperature and trip information display (if equipped) Displays the outside temperature and trip information. (P. 169434) Clock (P. 433) H (Hour) button (P. 433) M (Minute) button (P. 433) INFO button (if equipped) SELECT RESET button (if equipped) SETUP button (if equipped)
182
2
2-2. Instrument cluster
Outside temperature and trip information display (if equipped)
Every time the INFO button is pushed, the display toggles through these information. ● OUTSIDE (outside temperature display)
Displays the outside air temperature.
● AVG (average fuel consumption after refueling)
Displays the average fuel consumption since the vehi- cle was last refueled.
• The function can be reset by pushing the SELECT RESET button for more than 2 sec- onds.
• Use the displayed average fuel consumption as a
reference.
● INST (current fuel consumption)
Displays the current rate of fuel consumption.
● RANGE (driving range)
Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.
• This distance is computed based on your aver- age fuel consumption. As a result, the actual dis- tance that can be driven may differ from that displayed.
• When only a small amount of fuel is added to the
tank, the display may not be updated.
183
2-2. Instrument cluster
● Display off
■The accessory meter can be operated when The engine switch must be in the ON position.
■To select the unit A (English/U.S. customary system) or unit B (metric
unit) (vehicles without multi-information display) Press the SETUP button to change the units.
Information
Average fuel consumption and current fuel consumption Driving range Outside temperature
Unit A
MPG
MILES
°F
Unit B
L/100 Km
Km °C
CAUTION
■Caution while driving
Do not adjust the display. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.
184
2
2-3. Operating the lights and wipers Headlight switch
The headlights can be operated manually or automatically.
Type A
U.S.A.
Canada
lights
lights
running
OFF Vehicles with day- time light system: The daytime running turn on. The side marker, parking, tail, license plate, daytime run- ning (if equipped) and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on. The headlights, day- time running lights (if equipped) and all lights listed above turn on and off auto- matically. (When the engine switch is in the ON position)
185
2-3. Operating the lights and wipers
Type B
U.S.A.
Canada
186
lights
lights
running
OFF Vehicles with day- time light system: The daytime running turn on. The side marker, parking, tail, license plate, daytime run- ning (if equipped) and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on. The headlights, day- time running lights (if equipped) and all lights listed above turn on and off auto- matically. (When the engine switch is in the ON position)
2
2-3. Operating the lights and wipers
Type C
(When
running
The daytime running lights turn off. The headlights, side marker, parking, tail, license plate, day- time lights and instruments panel lights turn on and off automati- cally. the engine switch is in the ON position) The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on.
187
(When
running
The daytime running lights turn off. The headlights, side marker, parking, tail, license plate, day- time lights and instruments panel lights turn on and off automati- cally. the engine switch is in the ON position) The side marker, parking, tail, license plate, daytime run- ning lights and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on.
2-3. Operating the lights and wipers
Type D
188
2
2-3. Operating the lights and wipers
Turning on the high beam headlights
With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.
■Daytime running light system (if equipped)
●To make your vehicle more visible to other drivers, the front turn signal lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night. Type C and D: Daytime running lights can be turned off by operating the switch.
●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.
■Headlight control sensor
The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.
interferes with
189
2-3. Operating the lights and wipers
■Automatic light off system
●When the headlights come on: The headlights and tail lights automati- cally turn off after 30 seconds when all doors are closed with the engine switch turned to the ACC or LOCK position. (The lights turn off immedi- ately if the button on the wireless remote control is pressed after all doors are locked.)
●When only the tail lights come on: The tail lights turn off automatically with the engine switch turned to the ACC or LOCK position and the driver’s door is opened.
To turn the lights on again, turn the engine switch to the ON position, or turn position. the headlight switch off once and then back to the
or
■Customization
●That can be configured at Toyota dealer. (vehicles without multi-informa-
tion display) Settings (automatic light off system) can be changed. (Customizable features P. 627)
●It is possible to change the settings. (vehicles with multi-information dis-
play) (Feature customization P. 179)
NOTICE
■To prevent battery discharge
Do not leave the lights on longer than necessary when the engine is not run- ning.
190
2-3. Operating the lights and wipers Fog light switch
The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.
Type A
OFF Front fog lights ON
: If equipped
191
2-3. Operating the lights and wipers
Type B
OFF Front fog lights ON
192
2
2-3. Operating the lights and wipers Windshield wipers and washer
Wiper intervals can be adjusted for intermittent operation (when
or Type A
is selected.)
Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
193
Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts.
Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation
2-3. Operating the lights and wipers
Type B
194
2
2-3. Operating the lights and wipers
the
intermittent Increases windshield wiper frequency Decreases the intermittent windshield wiper frequency
Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts.
■The windshield wiper and washer can be operated when
The engine switch must be in the ON position.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.
195
2-3. Operating the lights and wipers
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.
■When a nozzle becomes blocked
In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
196
2-3. Operating the lights and wipers Rear window wiper and washer
Type A
Intermittent window wiper operation Normal window wiper operation Washer/wiper operation Washer/wiper operation
dual
dual
The rear window wiper oper- ates while the washer squirts.
197
2-3. Operating the lights and wipers
Type B
Intermittent window wiper operation Normal window wiper operation Washer/wiper operation Washer/wiper operation
dual
dual
The rear window wiper oper- ates while the washer squirts.
■The rear window wiper and washer can be operated when
●The engine switch must be in the ON position. ●The back window is fully closed.
■Customization that can be configured at Toyota dealer
Settings (e.g. washer linkage wiper control) can be changed. (Customizable featuresP. 627)
NOTICE
■When the rear window is dry
Do not use the wipers, as they may damage the rear window.
198
2-3. Operating the lights and wipers Headlight cleaner switch
Washer fluid can be sprayed on the headlights.
Press the switch to clean the headlights.
■The headlight cleaner can be operated when
The engine switch is in the ON position and the headlights are turned on.
NOTICE
■When the washer fluid tank is empty
Do not use this function when the washer fluid tank is empty. This may cause the washer fluid pump to overheat.
: If equipped
199
2-4. Using other driving systems Cruise control
Use the cruise control to maintain a set speed without depressing the accelerator pedal.
Indicator Cruise control switch
■ Setting the vehicle speed
Press the ON-OFF button to activate the cruise control.
indicator will
Cruise control come on. Press the button again deactivate the cruise control.
to
Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
The vehicle speed at the moment the lever is released becomes the set speed.
200
2
2-4. Using other driving systems
■ Adjusting the set speed
To change the set speed, operate the lever until the desired set speed is obtained.
Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.
the
The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.
■ Canceling and resuming the constant speed control
Pulling the lever toward you
cancels the constant speed
control.
The speed setting is also can-
celed when the brakes are
applied.
Pushing
resumes
speed control.
Resuming is available when
the vehicle speed is more than
approximately 25 mph
(40
km/h).
lever up constant
the the
201
2-4. Using other driving systems
■Cruise control can be set when
●The shift lever is in the D or range 4 or higher of S has been selected. ●Vehicle speed is above approximately 25 mph (40 km/h).
■Accelerating after setting the vehicle speed
●The vehicle can be accelerated normally. After acceleration, the set
speed resumes.
●Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.
■Automatic cruise control cancelation
Cruise control will stop maintaining the vehicle speed in any of the following situations. ●Actual vehicle speed falls more than approximately 10 mph (16 km/h)
below the preset vehicle speed. At this time, the memorized set speed is not retained.
●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated. ●The operation cannot be switched for 5 seconds or more after operating the front wheel drive control switch or the center differential lock switch. (4WD models)
■If the cruise control indicator flashes
Press the ON-OFF button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
202
2
2-4. Using other driving systems
CAUTION
■To avoid operating the cruise control by mistake
Switch the cruise control off using the ON-OFF button when not in use.
■Situations unsuitable for cruise control
Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills
Vehicle speed may exceed the set speed when driving down a steep hill.
●When your vehicle is towing a trailer or during emergency towing
203
2-4. Using other driving systems Dynamic laser cruise control
Dynamic laser cruise control supplements conventional cruise con- trol with a vehicle-to-vehicle distance control. In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates or decelerates in order to maintain a set following distance from vehi- cles ahead.
Indicator Display Set speed Cruise control switch Vehicle-to-vehicle distance button
204
: If equipped
2-4. Using other driving systems
■ Setting the vehicle speed (vehicle-to-vehicle distance con-
trol mode)
Press the ON-OFF button to activate the cruise control.
indicator will
Cruise control come on. Press the button again deactivate the cruise control.
to
Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
SET will be displayed. The vehicle speed at the moment the lever is released becomes the set speed.
205
2-4. Using other driving systems
■ Adjusting the set speed
To change the set speed, operate the lever until the desired set speed is displayed.
Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.
the
In the vehicle-to-vehicle distance control mode, the set speed will be increased or decreased as follows: • When the set speed is shown in “MPH”
Fine adjustment: By approximately 5 mph (8 km/h) each time the
lever is operated
Large adjustment: By approximately 5 mph (8 km/h) for each 0.75
seconds the lever is held
• When the set speed is shown in “km/h”
Fine adjustment: By approximately 3.1 mph (5 km/h) each time the
lever is operated
Large adjustment: By approximately 3.1 mph (5 km/h) for each 0.75
seconds the lever is held
In the constant speed control mode (P. 211), the set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.
206
2
2-4. Using other driving systems
■ Changing the vehicle-to-vehicle distance
Preceding vehicle mark
Pressing the button changes the vehicle-to-vehicle dis- tance as follows:
Long Medium Short The vehicle-to-vehicle distance is set automatically to long mode when the engine switch is turned to the ON position. If a vehicle is running ahead of you, the preceding vehicle mark will also be displayed.
■ Vehicle-to-vehicle distance settings
Select a distance from the table below. Note that the distances shown correspond to a vehicle speed of 55 mph (90 km/h). Vehi- cle-to-vehicle distance increases/decreases in accordance with vehicle speed.
Distance options
Long Medium Short
Vehicle-to-vehicle distance Approximately 245 ft. (75 m) Approximately 165 ft. (50 m) Approximately 100 ft. (30 m)
207
2-4. Using other driving systems
■ Canceling and resuming the speed control
the
Pulling the lever toward you
cancels the cruise control.
The speed setting is also can-
celed when the brakes are
applied.
Pushing
lever up
resumes the cruise control
and returns vehicle speed
to the set speed.
Resuming is available when
the vehicle speed is more than
approximately 25 mph
(40
km/h).
208
2-4. Using other driving systems
Driving in vehicle-to-vehicle distance control mode
This mode employs a laser radar sensor to detect the presence of vehicles up to approximately 400 ft. (120 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to main- tain a suitable following distance from the vehicle ahead.
Note that vehicle-to-vehicle distance will close in when traveling on long downhill slopes.
Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver. The desired vehicle-to- vehicle distance can also be set by operating the vehicle-to-vehicle dis- tance control. Example of deceleration cruising When the vehicle ahead is driving slower than the set speed When a vehicle is detected running ahead of you, the system automati- cally decelerates your vehicle. When a greater reduction in vehicle speed is necessary, the system applies the brakes. A warning tone warns you when the system cannot decelerate sufficiently to prevent your vehicle from closing in on the vehicle ahead.
209
2-4. Using other driving systems
Example of follow-up cruising When following a vehicle driving slower than the set speed The system continues follow-up cruising while adjusting for changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle dis- tance set by the driver. Example of acceleration When there are no longer any vehicles ahead driving slower than the set speed The system accelerates until the set speed is reached. The system then returns to constant speed cruising.
Approach warning
When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the dis- play will flash and the buzzer will sound to alert the driver. An exam- ple of this would be if another driver cuts in front of you while you are following a vehicle. Apply the brakes to ensure an appropriate vehi- cle-to-vehicle distance. ■ Warnings may not occur when
In the following instances, there is a possibility that the warnings will not occur: ● When the speed of the vehicle ahead matches or exceeds your
vehicle speed
● When the vehicle ahead is traveling at an extremely slow speed ● Immediately after the cruise control speed was set ● At the instant the accelerator is applied
210
2
2-4. Using other driving systems
Selecting conventional constant speed control mode
Constant speed control mode differs from vehicle-to-vehicle distance control mode. When constant speed control mode is selected, your vehicle will maintain a set speed regardless of whether or not there are other vehicles in the lane ahead.
Press the ON-OFF button to
activate the cruise control.
Press the button again to deacti-
vate the cruise control.
Switch to constant speed con-
trol mode.
(Push the lever forward and
hold
for approximately one
second.)
Constant speed control mode
indicator will come on.
When in constant speed control
mode, to return to vehicle-to-vehi-
cle distance control mode, push
the lever forward again and hold
for approximately 1 second.
After the desired speed has been
set, it is not possible to return to
vehicle-to-vehicle distance con-
trol mode.
If the engine switch is turned off
and then turned to the ON posi-
tion again, the vehicle will auto-
matically
to vehicle-to-
vehicle distance control mode.
Adjusting the speed setting:
P. 206
Canceling and
speed setting: P. 208
resuming
return
the
211
2-4. Using other driving systems
■Dynamic laser cruise control can be set when
●The shift lever is in the D or range 4 or higher of S has been selected. ●Vehicle speed is above approximately 30 mph (50 km/h).
■Switching modes
The mode cannot be switched to constant speed control mode if vehicle-to- vehicle distance control mode has been used. The mode also cannot be switched from constant speed control to vehicle-to-vehicle distance control mode. Turn the system off by pressing the ON-OFF button, and turn it on again.
■Accelerating after setting the vehicle speed
The vehicle can accelerate normally. After acceleration, the set speed resumes. However, during vehicle-to-vehicle distance control mode, the vehicle speed may decrease below the set speed in order to maintain the distance to the vehicle ahead.
■Automatic cancelation of vehicle-to-vehicle distance control
Vehicle-to-vehicle distance control driving is automatically canceled in the following situations: ●Actual vehicle speed falls below approximately 25 mph (40 km/h) ●VSC is activated ●The sensor cannot operate correctly because it is covered in some way.* ●The windshield wipers are operating at high or low speed.* ●The operation cannot be switched for 5 seconds or more after operating the front wheel drive control switch or the center differential lock switch. (4WD models) *:Vehicle-to-vehicle distance control driving must be reset by pressing the ON-OFF button again.
If vehicle-to-vehicle distance control driving is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer.
212
2
2-4. Using other driving systems
■Automatic cancelation of constant speed control
The cruise control will stop maintaining the vehicle speed in the following sit- uations: ●Actual vehicle speed is more than approximately 10 mph (16 km/h)
below the set vehicle speed At this time, the memorized set speed is not retained.
●Vehicle speed falls below approximately 25 mph (40 km/h) ●VSC is activated ●The operation cannot be switched for 5 seconds or more after operating the front wheel drive control switch or the center differential lock switch. (4WD models)
■Laser radar sensor
Always keep the sensor clean to ensure that the vehicle-to-vehicle distance con- trol operates properly. (Some obstruc- tions, such as snow, ice and plastic objects, cannot be detected by the obstruction sensor.) Dynamic laser cruise control is canceled if an obstruction is detected.
■Warning lights, messages and buzzers for dynamic laser cruise control Warning lights, messages and buzzers are used to indicate a system mal- function or to inform the driver of the need for caution while driving. (P. 568)
■Certification
This product is a class I laser product complied with 21C.F.R part 1040.10
and 1040.11.
213
2-4. Using other driving systems
CAUTION
■Before using dynamic laser cruise control
Do not overly rely on vehicle-to-vehicle distance control. Be aware of the set speed. If automatic deceleration/acceleration is not appropriate, adjust the vehicle speed, as well as the distance between your vehicle and vehicles ahead by applying the brakes etc.
■Cautions regarding the driving assist systems
Observe the following precautions. Failure to do so may cause an accident resulting in death or serious injury. ●Assisting the driver to measure following distance
The dynamic laser cruise control is only intended to help the driver in determining the following distance between the driver’s own vehicle and a designated vehicle traveling ahead. It is not a mechanism that allows care- less or inattentive driving, and it is not a system that can assist the driver in low-visibility conditions. It is still necessary for driver to pay close attention to the vehicle’s surroundings.
●Assisting the driver to judge proper following distance
The dynamic laser cruise control determines whether the following dis- tance between the driver’s own vehicle and a designated vehicle traveling ahead is appropriate or not. It is not capable of making any other type of judgement. Therefore, it is absolutely necessary for the driver to remain vigilant and to determine whether or not there is a possibility of danger in any given situation.
●Assisting the driver to operate the vehicle
The dynamic laser cruise control has no capability to prevent or avoid a collision with a vehicle traveling ahead. Therefore, if there is ever any dan- ger, the driver must take immediate and direct control of the vehicle and act appropriately in order to ensure the safety of all involved.
■To avoid inadvertent cruise control activation
Switch the cruise control off using the ON-OFF button when not in use.
214
2
2-4. Using other driving systems
CAUTION
■Situations unsuitable for dynamic laser cruise control
Do not use dynamic laser cruise control in any of the following situations. Doing so may result in inappropriate speed control and could cause an acci- dent resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep downhills, or where there are sudden changes between sharp up
and down gradients Vehicle speed may exceed the set speed when driving down a steep hill.
●At entrances to expressways ●When weather conditions are bad enough that they may prevent the sen- sors from functioning correctly (fog, rain, snow, sandstorm, direct sunlight, etc.)
●When an approach warning buzzer is heard often ●When your vehicle is towing a trailer or during emergency towing
215
2-4. Using other driving systems
CAUTION
■When the sensor may not be correctly detecting the vehicle ahead
Apply the brakes as necessary when any of the following types of vehicles are in front of you. As the sensor may not be able to correctly detect these types of vehicles, the approach warning (P. 568) will not be activated, and a fatal or serious accident may result. ●The vehicle ahead has higher ground clearance, which means that the
placement of the reflectors is in a higher position.
●The rear section of the vehicle ahead is extremely dirty. ●The vehicle ahead or other vehicles around you are flinging up water or
snow.
●Excessive exhaust gas (black smoke) is coming from the vehicle ahead or
other vehicles around you, obscuring your front view.
●There is an obstruction (protective film, sticker, etc.) on the reflectors on the vehicle ahead, or reflectors are not installed on the vehicle ahead or are damaged.
●Heavy luggage in the luggage compartment or rear seats is causing the
nose of your vehicle to tilt up. ●Vehicles that cut in suddenly ●Vehicles traveling at low speeds ●Vehicles that are not moving ●Vehicles with small rear ends (trailers with no load on board etc.) ●Motorcycles traveling in the same lane
216
2
2-4. Using other driving systems
CAUTION
■Conditions under which the vehicle-to-vehicle distance control may
not function correctly Apply the brakes as necessary in the following conditions as the laser radar sensor may not be able to correctly detect vehicles ahead, and a fatal or serious accident may result. ●When water or snow thrown up by the surrounding vehicles hinders the
functioning of the sensor
●When your vehicle is pointing upwards (caused by a heavy load in the lug-
gage compartment etc.)
●When the road curves or when the lanes are narrow ●When steering wheel operation or your position in the lane is unstable ●When the vehicle ahead of you decelerates suddenly ●When your vehicle is towing a trailer or during emergency towing
■Handling the laser radar sensor
Observe the following to ensure the cruise control system can function effec- tively. Otherwise, the system may not function correctly and could result in an acci- dent. ●Keep the sensor clean at all times.
Clean the sensor with a soft cloth so you do not mark or damage them.
●Do not subject the sensor or surrounding area to a strong impact.
If the sensor moves even slightly off position, the system may malfunction. If the sensor or surrounding area is subject to a strong impact, always have the area inspected and adjusted by a Toyota dealer.
●Do not disassemble the sensor. ●Do not attach accessories or stickers to the sensor, surrounding area. ●Do not modify or paint the sensor. ●Do not replace them with non-genuine parts.
217
2-4. Using other driving systems Intuitive parking assist
The intuitive parking assist is designed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer when parking the vehicle. This system uses sensors to detect obstructions. This system works when the engine switch is in the ON position and the shift lever is not in P. Back and rear corner sensors work only when the shift lever is in R. Front corner sensors work when: ● The shift lever is in R ● The shift lever is not in P or R and vehicle speed is approximate
6 mph (10 km/h) or less.
Back sensors Rear corner sensors Front corner sensors
218
: If equipped
■ Intuitive parking assist switch
2-4. Using other driving systems
Press the switch to turn on. (To turn off, press the switch again.) When on, the buzzer sounds to inform the driver that the system is operational. At this time, the indicator will come on.
The distance and buzzer
■ When a sensor detects an obstacle.
The buzzer sounds.
Back sensors
Zone
Far
Mid
Near
Distance
shown as
in in. (mm)
Approximately
70.9 — 45.3
(1800 — 1150)
Approximately
45.3 — 33.5
(1150 — 850)
Approximately
33.5 (850) or
less
Indicator and buzzer
Intermittent
Fast
intermittent
Continuous
219