Login- Download PDF Manual
-
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
■Notes for the unlocking function
●A sudden approach to the effective range or door handle may prevent the doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.
●Gripping the door handle when wearing a glove may not unlock the door. Remove the gloves and touch the sensor on the back of the handle again.
●If there is another electronic key in the detection area, it may take slightly
longer to unlock the doors after the door handle is gripped.
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 6 ft.
(2 m) of the vehicle.
●The smart key system can be deactivated in advance. Ask your Toyota
dealer for details.
■To operate the smart key system properly
Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention function may not operate.)
■If the smart key system does not operate properly
●Locking and unlocking the doors: Use the mechanical key. (P. 479) ●Starting the hybrid system:P. 479
57
1-3. Opening, closing and locking the doors
■Electronic key battery depletion
●The standard battery life is 1 to 2 years. ●If the battery becomes low, an alarm will sound in the cabin when the
hybrid system stops. (P. 455)
●As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (P. 401) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller. • The LED indicator on the key surface does not turn on.
●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field: • TVs • Personal computers • Cellular phones, cordless phones and battery chargers • Recharging cellular phones or cordless phones • Induction cookers • Table lamps
■When the electronic key battery is fully depleted
P. 401
■If the smart key system has been deactivated in a customized setting ●Locking and unlocking the doors: Use the wireless remote control or
mechanical key. (P. 61, 479)
●Starting the hybrid system and changing “POWER” switch modes:
P. 479
●Stopping the hybrid system: P. 480
■Customization that can be configured at Toyota dealer
Settings (e. g. operation signals) can be changed. (Customizable features: P. 522)
58
1
1-3. Opening, closing and locking the doors
■Certification for the smart key system
U.S.A. FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device. U.S.A. FCC ID: NI4TMLF10-6
FCC ID: NI4TMLF10-7
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada NOTE: This device complies with Industry Canada licence-exempt RSS stan- dard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.59
1-3. Opening, closing and locking the doors
CAUTION
■Caution regarding interference with electronic devices
●People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the smart key system antennas. (P. 50) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.
●Users of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implant- able cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
Ask your Toyota dealer for details for disabling the entry function.
60
1-3. Opening, closing and locking the doors Wireless remote control
The wireless remote control can be used to lock and unlock the vehi- cle. Vehicles without a smart key system
Vehicles with a smart key system
Locks all the doors Check that the door is securely locked. Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Sounds the alarm (press and hold)
Locks all the doors Check that the door is securely locked. Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Sounds the alarm (press and hold)
61
1-3. Opening, closing and locking the doors
■Operation signals
Vehicles without a smart key system The emergency flashers flash to indicate that the doors have been locked/ unlocked. (Locked: once; Unlocked: twice) Vehicles with a smart key system A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: once; Unlocked: twice)
■ Panic mode
Vehicles without a smart key system
Vehicles with a smart key system
When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.
When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the electronic key.
■Door lock buzzer (vehicles with a smart key system)
If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.
■Security feature
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
62
1
1-3. Opening, closing and locking the doors
■Conditions affecting operation
Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: ●When the wireless key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise
●When carrying a portable radio, cellular phone or other wireless commu-
nication device
●When the wireless key is in contact with, or is covered by a metallic
object
●When other wireless keys (that emits radio waves) are being used
nearby
●If window tint with a metallic content or metallic objects are attached to
the rear window
Vehicles with a smart key system P. 55
■If the wireless remote control does not operate properly (vehicles with
a smart key system) Locking and unlocking the doors: Use the mechanical key. (P. 479)
■Key battery depletion
Vehicles without a smart key system If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (P. 401) Vehicles with a smart key system P. 58
■When the electronic key battery is fully depleted
P. 401
63
1-3. Opening, closing and locking the doors
■Confirmation of the registered key number (vehicles with a smart key
system) The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details.
■Customization that can be configured at Toyota dealer
Settings (e.g. wireless remote control system) can be changed. (Customizable features P. 522)
■ Certification for wireless remote control
U.S.A. FCC ID: HYQ23AAC FCC ID: HYQ12BDM NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.
64
1-3. Opening, closing and locking the doors Side doors
The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (if equipped)
P. 47
■ Wireless remote control
P. 61
■ Key Turning the key operates the doors as follows: Vehicles without a smart key system
Locks all the doors Unlocks all the doors Driver’s side only: Turning the key unlocks the driver’s door. Turning the key again within 5
seconds unlocks the other doors.Vehicles with a smart key system The doors can also be locked and unlocked with the mechanical key. (P. 479) ■ Door lock switch
Locks all the doors Unlocks all the doors
65
1-3. Opening, closing and locking the doors
■ Inside lock buttons
Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Locking the front doors from the outside without a key
STEP 1
STEP 2
Move the inside door lock button to the lock position. Close the door.
Vehicles without a smart key system
The door cannot be locked if either of the front doors is open and the key is in the engine switch.
Vehicles with a smart key system
The door cannot be locked if the “POWER” switch is in ACCES- SORY or ON mode, or the electronic key is left inside the vehicle. The key may not be detected correctly and the door may be locked.
66
Rear door child-protector lock
1-3. Opening, closing and locking the doors
The door cannot be opened from inside the vehicle when the lock is set.
Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
67
1-3. Opening, closing and locking the doors
Automatic door locking and unlocking systems
The following functions can be set or canceled:
Function
Operation
Shift position linked door locking function Shift position linked door unlocking function Speed linked door lock- ing function (vehicles with a smart key sys- tem) Driver’s door linked door unlocking function (vehicles without a smart key system) Driver’s door linked door unlocking function (vehicles with a smart key system) ■ Setting and canceling the functions
Shifting the shift lever out of P locks all doors.
Shifting the shift lever to P unlocks all doors.
All doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.
All doors are unlocked when the driver’s door is opened within 45 seconds after turn- ing the engine switch to “ACC” or “LOCK”.
All doors are unlocked when the driver’s door is opened within 45 seconds after turn- ing the “POWER” switch off.
To switch between setting and canceling, follow the procedure below:
Vehicles without a smart key system Close all the doors and turn the engine switch to the “ON” position. (Perform Vehicles with a smart key system Close all the doors and switch the “POWER” switch to ON mode. (Perform
within 20 seconds.)
within 20 seconds.)
STEP 2
STEP 2
STEP 1
68
1
STEP 2
1-3. Opening, closing and locking the doors
Shift the shift lever to P or N, and press and hold the door lock switch ( ) for about 5 sec- onds then release.
or
The shift position corresponding to the desired function to be set are shown as follows. Use the same procedure to can- cel the function.
Function
Shift position
Door lock switch
position
Shift position linked door lock- ing function Shift position linked door unlocking function Speed linked door locking func- tion Driver’s door linked door unlock- ing function
When the setting or canceling operation is complete, all doors are locked and then unlocked.
■Using the mechanical key (vehicles with a smart key system)
The doors can also be locked and unlocked with the mechanical key. (P. 479)
■If a wrong key is used (vehicles with a smart key system)
The key cylinder rotates freely to isolate inside mechanism. ■Customization that can be configured at Toyota dealer
Settings (e.g. unlocking function using a key) can be changed. (Customizable features P. 522)
69
1-3. Opening, closing and locking the doors
CAUTION
■To prevent an accident
Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all the doors are properly closed. ●Do not pull the inside handle of the doors while driving.
The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
●Set the rear door child-protector locks when children are seated in the rear
seats.
70
1-3. Opening, closing and locking the doors Back door
The back door can be locked/unlocked and opened by the following procedures. ■ Locking and unlocking the back door Wireless remote control P. 61
Door lock switches P. 65
Entry function (if equipped) P. 47
■ Opening the back door from outside the vehicleRaise the back door while pushing up the back door opener switch.
The back door cannot be closed immediately after the back door opener switch is pushed.
71
1-3. Opening, closing and locking the doors
When closing the back door
Lower the back door using the back door handle, and make sure to push the back door down from the outside to close it.
CAUTION
■Caution while driving
●Keep the back door closed while driving.
If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door before driving.
●Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident.
●Never let anyone sit in the luggage compartment. In the event of sudden
braking or a collision, they are susceptible to death or serious injury.
72
1
1-3. Opening, closing and locking the doors
CAUTION
■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to play in the luggage compartment.
If a child is accidentally locked in the luggage compartment, they could have heat exhaustion or other injuries.
●Do not allow a child to open or close the back door.
Doing so may cause the back door to move unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.
■Operating the back door
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●Remove any heavy loads, such as snow and ice, from the back door before opening it. Failure to do so may cause the back door to suddenly shut again after it is opened.
●When opening or closing the back door, thoroughly check to make sure
the surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●Use caution when opening or closing the back door in windy weather as it
may move abruptly in strong wind.
73
1-3. Opening, closing and locking the doors
CAUTION
●The back door may suddenly shut if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage com- partment.
●When closing the back door, take extra care to prevent your fingers etc. from being caught.
●When closing the back door, make sure to press it lightly on its outer surface. If the back door handle is used to fully close the back door, it may result in hands or arms being caught.
●Do not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay. Doing so may cause hands to be caught or the back door damper stay to break, causing an accident.
●If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended.
74
1
1-3. Opening, closing and locking the doors
NOTICE
■Back door damper stays
The back door is equipped with damper stays that hold the back door in place. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction.
●Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod.
●Do not touch the damper stay rod with
gloves or other fabric items.
●Do not attach any accessories other than genuine Toyota parts to the back door.
●Do not place your hand on the damper
stay or apply lateral forces to it.
75
1-4. Adjustable components (seats, mirrors, steering wheel) Front seats
Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (if equipped)
CAUTION
■Seat adjustment
●Be careful that the seat does not hit passengers or luggage. ●To reduce the risk of sliding under the lap belt during a collision, do not
recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident. Adjustments should not be made while driving as the seat may unexpect- edly move and cause the driver to lose control of the vehicle.
●After adjusting the seat, make sure that the seat is locked in position.
76
1-4. Adjustable components (seats, mirrors, steering wheel) Rear seats
The seatbacks of the rear seats can be folded down.
Folding down the rear seatbacks
■ Before folding down the rear seatbacks STEP 1
Stow the rear seat belt buckles as shown.
STEP 2
Stow the seat belts.
Center P. 86
OutsideUse the seat belt hangers to pre- vent the belts from being tan- gled.
77
1-4. Adjustable components (seats, mirrors, steering wheel)
STEP 3
STEP 4
Remove the outside head restraints. (P. 81) Lower the center head restraint to the lowest position. (P. 81)
■ Folding down rear seatbacks Vehicles with a split rear seats
Pull the seatback lock release knob and the seatback down.
fold
Each seatback may be folded separately.
Vehicles with a non-split rear seat
Pull both seatback lock release knobs at the same time and fold the seatback down.
78
1
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■When folding the rear seatbacks down
Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not fold the seatbacks down while driving. ●Stop the vehicle on level ground, set the parking brake and shift the shift
lever to P.
●Do not allow anyone to sit on a folded seatback or in the luggage compart-
ment while driving.
●Do not allow children to enter the luggage compartment. ●For vehicles with split rear seats, do not allow anyone sit on the rear center seat if the rear right seat is folded down, as the seat belt buckle for the rear center seat belt is then concealed under the folded seat and cannot be used.
●Be careful not to catch your hand when folding the rear seatbacks. ●If it is necessary to detach the head restraints, remove it from the vehicle or store it securely in the luggage compartment. This will prevent it from injuring passengers in the event of sudden braking, sudden swerving or an accident.
●Adjust the position of the front seat before folding down the rear seatbacks so that the front seat does not interfere with the rear seatbacks when fold- ing down the rear seatbacks.
79
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■After returning the rear seatback to the upright position
Observe the following precautions. Failure to do so may result in death or serious injury.
●Make sure that the seatback is securely locked in position by lightly pushing it back and forth. If the seatback is not securely locked, the red marking will be visible on the seatback lock release knob. Make sure that the red marking is not visible.
●Check that the seat belts are not twisted or caught in the seatback.
NOTICE
■Stowing the seat belts
The seat belts and the buckles must be stowed before you fold down the rear seatbacks.
80
1
1-4. Adjustable components (seats, mirrors, steering wheel) Head restraints
Head restraints are provided for all seats. Vehicles with adjustable type head restraints
Up Pull the head restraint up. Down Push the head restraint down while pushing the lock release button.
Lock release button
■Removing the head restraints
Front adjustable and rear center head restraints
Pull the head restraint up while pushing the lock release button.
Lock release button
Rear outside head restraints STEP 1
Pull the seatback lock release knob and fold down the seatback until it reaches the position where the head restraints can be removed.
81
1-4. Adjustable components (seats, mirrors, steering wheel)
STEP 2
Pull the head restraint up while pressing the lock release button.
Lock release buttons
■Installing the head restraints
Front adjustable and rear center head restraints
Lock release button
Rear outside head restraints STEP 1
Align the head restraint with installation holes and push it down to the lock posi- tion. Press and hold the lock release button when lowering the head restraint.
Pull the lock release knob and fold down the seatback until it reaches the position where restraints can be installed.
the head
STEP 2
Lock release button
Align the head restraint with installation holes and push it down to the lock posi- tion. Press and hold the lock release button when lowering the head restraint.
82
1-4. Adjustable components (seats, mirrors, steering wheel)
■Adjusting the height of the head restraints (vehicles with adjustable
type head restraints)
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
■Adjusting the rear center seat head restraints
Always raise the head restraint one level from the stowed position when using.
CAUTION
■Head restraint precautions (vehicles with adjustable type head
restraints) Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure
they are locked in position.
●Do not drive with the head restraints removed.
83
1-4. Adjustable components (seats, mirrors, steering wheel) Seat belts
Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts
● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.
● Position the lap belt as low
as possible over the hips.
● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.
■ Fastening and releasing the seat belt
To fasten the seat belt, push the plate into the buckle until a click sound is heard. To release the seat belt, press the release button.
Release button
84
1-4. Adjustable components (seats, mirrors, steering wheel)
Rear center seat belt
■ Fastening the seat belt The rear center seat belt is a 3-point type restraint with 2 buckles. Both seat belt buckles must be correctly located and securely latched for proper operation.
STEP 1
STEP 2
Push the tabs back all the way into the cover and then remove the tabs.
Push tab “B” into the buckle until a click sound is heard. Push tab “A” into the buckle until a click sound is heard.
85
1-4. Adjustable components (seats, mirrors, steering wheel)
■ Releasing the seat belt
Release the rear center seat belt only when necessary, such as when folding down the rear seat. For safety, always store the plate in the designated place after releasing it.
To release tab “A”, press the release button. To release tab “B”, insert the key (P. 44) or tab “A” into the hole on the buckle. Retract the belt slowly when releasing and stowing the seat belt.
STEP 1
86
1-4. Adjustable components (seats, mirrors, steering wheel)
Holding tab “A” and “B” together, insert both tabs all the way into the cover on the roof.
STEP 2
STEP 3
With tab “B” inserted all the way into the cover, move tab “A” slightly back toward the cover’s inlet, so that it blocks the inlet.
87
1-4. Adjustable components (seats, mirrors, steering wheel)
Seat belt pretensioners (front seats)
The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal or side collision.
The pretensioner does not acti- vate in the event of a minor frontal impact, a minor side impact, a rear impact or a vehicle rollover.
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
■Automatic locking retractor (ALR)
When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (P. 140)
■Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (P. 136) ●When the child becomes large enough to properly wear the vehicle’s
seat belt, follow the instructions on P. 84 regarding seat belt usage.
88
1-4. Adjustable components (seats, mirrors, steering wheel)
■Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.
■Seat belt extender
If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
they are not
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failure to do so may cause death or serious injury. ■Wearing a seat belt
●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at once, including children.
●Toyota recommends that children be seated in the rear seat and always
use a seat belt and/or an appropriate child restraint system.
●To achieve a proper seating position, do not recline the seat more than necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.
89
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (P. 84) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only the pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a colli- sion.
■People suffering illness
Obtain medical advice and wear the seat belt in the proper way. (P. 84)
■When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
■Seat belt pretensioners
●Do not place anything, such as a cushion, on the front passenger’s seat.
Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.
●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
90
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat belt damage and wear
●Do not damage the seat belts by allowing the belt, plate, or buckle to be
jammed in the door.
●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.
●Ensure that the belt and plate are locked and the belt is not twisted.
If the seat belt does not function correctly, immediately contact your Toyota dealer.
●Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there’s no obvious damage.
●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.
■When using or storing the rear center seat belt
●Do not use the rear center seat belt
with either buckle released. Fastening only one of the buckles may result in death or serious injury in case of sudden braking or a collision.
●For vehicles with split rear seats, do not allow anyone sit on the rear center seat if the rear right seat is folded down, as the seat belt buckle for the rear center seat belt is then concealed under the folded seat and cannot be used.
●When storing the rear center seat belt, ensure that the tabs are securely inserted into the cover on the roof. If the tabs are not stowed properly, they may drop from the cover while driving, resulting in serious injury.
91
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Using a seat belt extender
●Do not wear the seat belt extender if you can fasten the seat belt without
the extender.
●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.
NOTICE
■When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
92
1-4. Adjustable components (seats, mirrors, steering wheel) Steering wheel
The steering wheel can be adjusted to a comfortable position.
STEP 1
STEP 2
Hold the steering wheel and push the lever down.
Adjust to the ideal position by moving the steering wheel horizontally and vertically.
After adjustment, pull the lever up the steering wheel.
to secure
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.
■After adjusting the steering wheel
Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury.
93
1-4. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror
The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver's seating posture.
Adjusting the height of rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
Anti-glare function
Reflected light from the headlights of vehicles behind can be reduced by operating the lever.
Normal position Anti-glare position
94
1-4. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Caution while driving
Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
95
1-4. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors
Mirror angle can be adjusted using the switch.
STEP 1
STEP 2
To select a mirror to adjust, press the switch.
Left Right
To adjust the mirror, press the switch.
Up Right Down Left
Folding the mirrors
Push the mirror back in the direc- tion of the vehicle’s rear.
96
1
1-4. Adjustable components (seats, mirrors, steering wheel)
■Mirror angle can be adjusted when
Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “POWER” switch is in ACCESSORY or ON mode.
■When the mirrors are fogged up (vehicles with outside rear view mirror
defoggers) The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defoggers. (P. 247)
CAUTION
■When driving the vehicle
Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly
adjusted before driving. ■When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■When the mirror defoggers are operating (vehicles with an outside rear
view mirror defoggers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
97
1-5. Opening and closing the windows and moon roof Power windows
The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:
Closing One-touch closing (driver’s window only)* Opening One-touch opening (driver’s window only)*
*: To stop the window partway, operate the switch in the oppo- site direction.
Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.
Window lock switch
98
: If equipped
1
1-5. Opening and closing the windows and moon roof
■The power windows can be operated when
Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “POWER” switch is in ON mode.
■Operating the power windows after turning the hybrid system off
Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened. Vehicles with a smart key system The power windows can be operated for approximately 45 seconds even after the “POWER” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.
■Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
■When the power window does not close normally (driver’s window
only) If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the driver’s door. ●Vehicles without a smart key system: After stopping the vehicle, the win- dow can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.
●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch clos- ing position while the “POWER” switch is turned to ON mode.
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.
99
1-5. Opening and closing the windows and moon roof
STEP 1
STEP 2
STEP 3
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
CAUTION
■Closing the windows
Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●Do not allow children to operate the power windows.
Closing a power window on someone can cause death or serious injury. The driver is responsible for instructing children not to operate the power windows.
■Jam protection function (driver’s window only)
●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just
before the window fully closes.
100
1
1-5. Opening and closing the windows and moon roof Moon roof
Use the overhead switches to open and close the moon roof and tilt it up and down. ■ Opening and closing
■ Tilting up and down
Opens the moon roof* The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof. Closes the moon roof*
*: Lightly press either of the moon roof switches to stop the moon roof partway.
Tilts the moon roof up* Tilts the moon roof down*
*: Lightly press either of the moon roof switches to stop the moon roof partway.
: If equipped 101
1-5. Opening and closing the windows and moon roof
■The moon roof can be operated when
The “POWER” switch is in ON mode.
■Operating the moon roof after turning the hybrid system off
The moon roof can be operated for approximately 45 seconds after the “POWER” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.
■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.
102
STEP 2
STEP 3
STEP 2
STEP 3
STEP 4
1-5. Opening and closing the windows and moon roof
■When the moon roof does not close normally
Perform the following procedure: ●If the moon roof closes but then re-opens slightly STEP 1
Stop the vehicle. Press and hold the “CLOSE” switch.*1
The moon roof will close, re-open and pause for approximately 10
seconds.*2 Then it will close again, tilt up and pause for approxi- mately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.●If the moon roof tilts down but then tilts back up STEP 1
Stop the vehicle. Press and hold the “TILT” switch*1 until the moon roof moves into the tilt up position and stops. Release the “TILT” switch once and then press and hold the “TILT” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up position.*2 Then it will adjust slightly and pause for approximately 1
second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.*1: If the switch is released at the incorrect time, the procedure will have to
be performed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “CLOSE” or “TILT” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.
If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
103
1-5. Opening and closing the windows and moon roof
■Moon roof open reminder function
An alarm will sound and a message is shown on the multi-information dis- play when the driver’s door is opened with the moon roof not fully closed and the “POWER” switch off.
CAUTION
■Opening the moon roof
Observe the following precautions. Failure to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
●Do not sit on top of the moon roof.
■Closing the moon roof
Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body in a position where it could be caught when the moon roof is being oper- ated.
●Do not allow children to operate the moon roof.
Closing the moon roof on someone can cause death or serious injury. The driver is responsible for instructing children not to operate the moon roof.
■Jam protection function
●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just
before the moon roof fully closes.
104
1
1-6. Refueling Opening the fuel tank cap
Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle
● Vehicles without a smart key system
Turn the engine switch off and ensure that all the doors and windows are closed.
● Vehicles with a smart key system
Turn the “POWER” switch off and ensure that all the doors and windows are closed.
● Confirm the type of fuel. (P. 107)
■ Opening the fuel tank cap STEP 1
Pull up the opener to open the fuel filler door.
STEP 2
Turn the fuel tank cap slowly to open.
105
1-6. Refueling
STEP 3
Hang the fuel tank cap on the back of the fuel filler door.
Closing the fuel tank cap
After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
106
1-6. Refueling
■Fuel types
Unleaded gasoline (Octane rating 87 [Research Octane Number 91] or higher)
■Use of ethanol blended gasoline in a gasoline engine
DO NOT use gasoline containing more than 15% ethanol.
(30% ethanol)
(50% ethanol)
(85% ethanol)
●Use only gasoline containing up to 15%
ethanol. DO NOT use any flex-fuel or gasoline that could contain more than 15% etha- nol, including from any pump labeled E30, E50, E85 (which are only some examples of fuel containing more than 15% ethanol).
●Make sure that the ethanol blended gasoline to be used has a suitable
Research Octane Number as outlined in “Fuel types”.
107
1-6. Refueling
CAUTION
■When refueling the vehicle
Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.
●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.
●Do not allow anyone that has not discharged static electricity from their
body to come close to an open fuel tank.
●Do not inhale vaporized fuel.
Fuel contains substances that are harmful if inhaled.
●Do not smoke while refueling the vehicle.
Doing so may cause the fuel to ignite and cause a fire.
●Do not return to the vehicle or touch any person or object that is statically
charged. This may cause static electricity to build up, resulting in a possible ignition hazard.
■When refueling
Observe the following precautions to prevent fuel overflowing from the fuel tank: ●Securely insert the fuel nozzle into the fuel filler neck ●Stop filling the tank after the fuel nozzle automatically clicks off ●Do not top off the fuel tank ■When replacing the fuel cap
Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
108
1-6. Refueling
NOTICE
■Refueling
Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle's painted surface.
109
1-7. Theft deterrent system Immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the hybrid system from starting if a key has not been previously regis- tered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. This system is designed to help prevent vehicle theft but does not guarantee absolute security against all vehicle thefts.
Vehicles without a smart key system The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed.
110
: If equipped
1
