2003 Toyota Celica Owners Manual

Washington, D.C. 20460

Vehicles equipped with a California Certified Emission Control System that are registered and operated in California or any state that adopts California emission warranty provisions are also covered by the California Emission Control Warranty (see page 20). Currently, Massachusetts and Vermont are the only other states to which the California Emission Control Warranty applies.

18

Your Warranties in Detail

DEALER CERTIFICATE

We (the dealership) want you to know that at the time your new Toyota vehicle is being delivered: 1) On the basis of written notification furnished by Toyota, we have

knowledge that the vehicle is covered by an EPA Certificate of Conformity.

2) We have visually inspected those emission control devices or portions

thereof that are visible without removing or adjusting any compo- nents or systems, emissions-related or otherwise. On the basis of this inspection, there are no apparent deficiencies in the installation of emission control devices by Toyota. (For purposes of this certificate, “emission control devices” is limited to devices installed on a vehicle for the sole or primary purpose of controlling emissions and which were not in general use before 1968.)

3) We have performed all emission control system preparations required by Toyota prior to the sale of the vehicle as set forth in Toyota’s cur- rent pre-delivery service manual.

4) Except as may be provided in Paragraph 5, if this vehicle fails an EPA-approved emissions test within three months or 4,000 miles (whichever comes first) of delivery to the ultimate purchaser, and the vehicle has been maintained and used in accordance with the writ- ten instructions for proper maintenance and use, Toyota will remedy

Federal Emission Control Warranty

the non-conformity free of charge under the terms of the Emission Performance Warranty.

5) If vehicle was used as a company car or demonstrator, check box and

complete the following: □ The vehicle with which this statement is delivered was placed into service as a company car or demonstrator prior to delivery. The Emission Performance Warranty period commenced on the date the vehicle was first placed into service, which was:

Month Day Year

Note: The dealership makes no representation or warranty that the emission control system or any part thereof is without defect or that the system will perform properly. The Emission Performance Warranty referred to in Paragraph 4 and furnished with the vehicle is solely that of the manufacturer.

This statement is required by section 207 of the Clean Air Act (42 U.S.C. 7541) and the EPA regulations issued thereunder.

Dealership Name

Your Warranties in Detail

19

California Emission Control Warranty

YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board (CARB) and Toyota are pleased to explain the emission control system warranty for your 2003 vehicle. In California, new motor vehicles must be designed, built and equipped to meet the state’s stringent anti-smog standards. CARB regulations require that Toyota must warrant the emission control system on your vehicle for the time periods indicated on this page, provided there has been no abuse, neglect or improper maintenance of your vehicle.

Your emission control system may include parts such as the fuel injection system, ignition system, catalytic converter and engine computer. Also included may be hoses, belts, connectors and other emissions-related assemblies.

Where a warrantable condition exists, Toyota will repair your vehicle at no cost to you, including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

1) For three years or 50,000 miles, whichever occurs first:*

• If your vehicle fails a smog-check test, all necessary repairs and adjustments will be made by Toyota to ensure that your vehicle passes the test. This is your Emission Control System PERFORMANCE WARRANTY.

• If any emissions-related part on your vehicle is defective, the part

will be repaired or replaced by Toyota. This is your SHORT-TERM Emission Control System DEFECT WARRANTY. Covered parts are listed on pages 15–16. Specific components may have longer coverage under the terms of the Powertrain Warranty.

2) For seven years or 70,000 miles, whichever occurs first:*

• If an emissions-related part listed on pages 22—23 is defective,

the part will be repaired or replaced by Toyota. This is your LONG-TERM Emission Control System DEFECT WARRANTY.

20

Your Warranties in Detail

* For 4-cylinder Camry models certified as partial zero-emission vehicles (PZEV), if any, coverage is 15 years or 150,000 miles, whichever occurs first.

OWNER’S WARRANTY RESPONSIBILITIES

WHAT IS NOT COVERED

California Emission Control Warranty

These warranty obligations do not apply to failures or noncompliance caused by: • The use of replacement parts not certified in accordance with

aftermarket parts certification regulations.

• The use of replacement parts not equivalent in quality or design to

original equipment parts.

Provisions under the “What Is Not Covered” section of the New Vehicle Limited Warranty also apply to this warranty.

You are responsible for performance of the required maintenance indi- cated in the Owner’s Manual and the Scheduled Maintenance Guide. Toyota recommends that you retain all receipts covering maintenance on your vehicle, but Toyota cannot deny warranty coverage solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.

You are responsible for presenting your vehicle to a Toyota dealership as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

You should also be aware that Toyota may deny you warranty coverage if your vehicle or a part has failed due to abuse, neglect, improper main- tenance or unapproved modifications.

If you have any questions regarding your warranty rights and responsi- bilities, you should contact the Toyota Customer Assistance Center at (800)331-4331 or the California Air Resources Board, Mobile Source Control Division, at 9528 Telstar Avenue, P.O. Box 8001, El Monte, CA 91734-8001.

Your Warranties in Detail

21

California Emission Control Warranty

PARTS LIST: LONG-TERM EMISSION DEFECT WARRANTY The parts listed here are covered for seven years or 70,000 miles from the vehicle’s in-service date, whichever occurs first.

Air/Fuel Metering System • Air-fuel ratio sensor on Highlander • Engine control computer (engine control module) • Fuel pump on Sienna • Mass air flow sensor on Tacoma equipped with 2RZ-FE and 3RZ-FE • Throttle body

Air Induction System • Intake manifold and intake air surge tank • Intake manifold gasket on MR2 Spyder

22

Your Warranties in Detail

Catalyst System • Catalytic converter (warm-up three-way catalyst) • Exhaust center pipe on Avalon, Corolla Matrix 4WD, Highlander

equipped with 1MZ-FE, Tacoma and Tundra equipped with 5VZ-FE • Exhaust front pipe on Avalon, Camry, Camry Solara, Celica, Corolla, Corolla Matrix 2WD, ECHO, Highlander equipped with 1MZ-FE, Land Cruiser, MR2 Spyder, Sequoia, Sienna, Tacoma, Tundra and 4Runner • Exhaust manifold on Avalon, Camry, Camry Solara, Highlander, Land Cruiser, MR2 Spyder, RAV4, Sequoia, Sienna, Tundra equipped with 2UZ-FE and 4Runner

• Exhaust manifold gasket on Land Cruiser, Sequoia, Tundra equipped

with 2UZ-FE and 4Runner

• Right exhaust manifold gasket on Sienna and on Avalon, Camry,

Camry Solara and Highlander models equipped with 1MZ-FE

Evaporative Control System • Charcoal canister on Highlander, Land Cruiser and 4Runner • Fuel tank

Ignition System • Knock sensor on Land Cruiser, MR2 Spyder, Sequoia, Tacoma

equipped with 5VZ-FE, Tundra and 4Runner

California Emission Control Warranty

MAINTENANCE

You are responsible for performance of the required maintenance indi- cated in the Owner’s Manual and the Scheduled Maintenance Guide. Toyota will not deny a warranty claim solely because you do not have records to show that you maintained your vehicle. However, any failure or noncompliance caused by lack of maintenance is not covered by this warranty.

When maintenance and repairs are paid for by you, these services may be performed by you or by any automotive service provider you choose. Toyota will not deny a warranty claim simply because you used a service provider other than a Toyota dealership for mainte- nance and repairs. However, any failure or non-compliance caused by improper maintenance or repairs is not covered by this warranty.

Your Warranties in Detail

23

California Emission Control Warranty

REPLACEMENT PARTS

IF YOUR VEHICLE FAILS A SMOG-CHECK TEST

To ensure optimum performance and maintain the quality built into your vehicle’s emission control systems, Toyota recommends the use of Genuine Toyota Parts when servicing or repairing the systems.

Warranty coverage is not dependent upon the use of any particular brand of replacement parts and you may elect to use non-Genuine Toyota Parts for maintenance and repairs. However, use of replace– ment parts that are not equivalent in quality to Genuine Toyota Parts may impair the effectiveness of the emission control systems.

If you use replacement parts that have maintenance or replacement schedules different from those of Genuine Toyota Parts, you must follow the maintenance and replacement schedules for the parts you are using. In addition, you should ensure that such parts are warranted by their manufacturers to be equivalent to Genuine Toyota Parts.

If your vehicle fails a smog-check test, you may make a claim under the Emission Performance Warranty. To do so, take your vehicle to an autho- rized Toyota dealership and present a copy of the smog-check test report. Also, take your maintenance records in case they are needed.

If your claim qualifies for coverage, the dealership will repair your vehi- cle within 30 days (unless a shorter period is required by law). If your claim is denied, Toyota will notify you in writing of the reason within the same period. If we fail to do so, we will repair your vehicle free of charge. The only exceptions allowed are when you request or agree to a delay, or a delay is caused by factors beyond the control of Toyota or the dealership.

For information on how to obtain service under the Emission Defect Warranty, see page 29, “Obtaining Warranty Service.”

24

Your Warranties in Detail

California Emission Control Warranty

REPAIR DELAYS

IF YOU HAVE QUESTIONS

If a Toyota dealership is unable to complete repairs on your vehicle within 30 days, you may have the repairs made under Toyota’s provisions for emergency warranty repairs. See page 29 for details.

If you have questions or concerns about your vehicle’s California emis- sion warranty coverage, please follow the steps described under “If You Need Assistance” on pages 4–5. You may also request information from or report complaints to:

California Air Resources Board Mobile Source Control Division 9528 Telstar Avenue P.O. Box 8001
El Monte, CA 91734-8001
(800)242-4450

Vehicles equipped with a California Certified Emission Control System that are registered and operated in California or any state that adopts California emission warranty provisions are covered by this warranty. Currently, Massachusetts and Vermont are the only other states to which this warranty applies. Vehicles covered by this warranty are also covered by the Federal Emission Control Warranty (see page 14).

Your Warranties in Detail

25

Tire Limited Warranty

OBTAINING WARRANTY SERVICE

ORIGINAL EQUIPMENT TIRE MANUFACTURERS

The tires that come as original equipment on your vehicle are warranted by their manufacturer and not Toyota. A separate warranty statement for the tires is in your glove box.

To obtain service for a tire defect, take the tire to an authorized dealer of the tire manufacturer. (Refer to your local phone directory for dealer locations.) Your Toyota dealer may also be able to assist you in obtaining warranty service from the manufacturer.

For additional warranty information or service assistance, contact the tire manufacturer directly.

Michelin/BFGoodrich P.O. Box 19001
Greenville, SC 29602
(800)847-3435

Toyo Tire (U.S.A.) Corporation 6261 Katella Ave., Ste. 2B Cypress, CA 90630
(800)442-8696

Yokohama Tire Corporation 601 South Acacia Avenue Fullerton, CA 92831
(800)722-9888

Bridgestone/Firestone One Bridgestone Park Nashville, TN 37214
(800)847-3272

Continental General Tire 1800 Continental Blvd. Charlotte, NC 28273
(800)847-3349

Goodyear Dunlop Tires North America, Ltd. P.O. Box 1109
Buffalo, NY 14240
(800)548-4714

Goodyear Tire and Rubber Co. 1144 East Market Street Akron, OH 44316
(800)321-2136

26

Your Warranties in Detail

Operation and Maintenance

GENERAL INFORMATION

WHERE TO GO FOR MAINTENANCE

You are responsible for ensuring that your Toyota is operated and main- tained according to the instructions in the Owner’s Manual and the Scheduled Maintenance Guide.

You may have maintenance performed on your vehicle by any qualified person or facility. However, Toyota recommends having maintenance performed by an authorized Toyota dealership.

You should keep detailed records of vehicle maintenance, since under some circumstances they may be required for warranty coverage. These records should include date of service, mileage at time of service and a description of service performed and/or parts installed. For your conve- nience, a maintenance log is included in the Scheduled Maintenance Guide. If you sell your vehicle, you should give your maintenance records to the new owner.

Toyota will not deny a warranty claim solely because you do not have records to show that you maintained your vehicle. However, damage or failures caused by lack of proper maintenance are not covered under warranty.

Toyota dealership technicians are specially trained to maintain and repair Toyota vehicles. They stay current on the latest service information through Toyota technical bulletins, service publications and training courses. Many are also certified through the Toyota Certification Program, which involves a series of rigorous written examinations. Feel free to ask any Toyota dealership to show you its technicians’ credentials.

You can be confident you’re getting the best possible service for your vehicle when you take it to a Toyota dealership. Plus, a Toyota dealer- ship will always use Genuine Toyota Parts designed specifically for your vehicle.

Your Responsibilities

27

Operation and Maintenance

REPLACEMENT PARTS

Warranty coverage is not dependent upon the use of any particular brand of replacement parts. However, Toyota recommends using only Genuine Toyota Parts when you need to replace a part on your vehicle. Like all Toyota products, Genuine Toyota Parts are built to the highest standards of quality, durability and performance. They are also designed to fit your vehicle’s exact specifications.

Your Toyota dealership maintains an extensive inventory of Genuine Toyota Parts to meet your vehicle service needs. And because it is linked electronically to Toyota’s Parts Distribution Centers, the dealership has quick access to any parts it may not have in stock.

Genuine Toyota Parts are covered by their own warranty (see your dealer for details) or the remainder of any applicable New Vehicle Limited Warranty, whichever is longer. Non–Genuine Toyota Parts, or any damage or failures resulting from their use, are not covered by any Toyota warranty.

28

Your Responsibilities

Obtaining Warranty Service

BY GEOGRAPHIC REGION

EMERGENCY REPAIRS

In the United States, U.S. Territories and Canada To obtain warranty service in the United States, U.S. territories or Canada, take your vehicle to an authorized Toyota dealership. If your vehicle cannot be driven, contact your nearest Toyota dealership for towing assistance. You do not have to pay for towing to the nearest Toyota deal- ership if your vehicle is inoperable due to failure of a warranted part.

Outside the United States, U.S. Territories and Canada If you are using your vehicle outside the United States, U.S. territories and Canada and need warranty service, contact a local Toyota dealer- ship. Please note, however, that your vehicle may not be repaired free of charge because the local Toyota distributor may have no obligation to provide warranty service for your vehicle, and/or your vehicle may not comply with local regulatory or environmental requirements.

If your vehicle is inoperable or unsafe to drive and there is no Toyota dealership reasonably available to make repairs, you may perform the repairs yourself or have them performed by another automotive service provider. Toyota will reimburse you for any of the repairs that are cov- ered by warranty. To receive reimbursement, present to an authorized Toyota dealership your paid repair invoices and any parts that were removed from the vehicle. You will be reimbursed for warranted parts at the manufacturer’s suggested retail price and warranted labor at a geographically appropriate hourly rate multiplied by Toyota’s recom- mended time allowance for the repair.

If your vehicle requires emergency repair, Toyota assumes no liability for subsequent failures caused by improper repairs or the use of non- Genuine Toyota Parts unless you have the vehicle properly repaired in a timely manner. To ensure that warranty coverage remains intact, have your vehicle inspected by an authorized Toyota dealership as soon as possible after an emergency repair.

Your Responsibilities

29

Notes

30

Notes

31

Notes

32

Owner Information Change Form

Check one:

Same owner, name and/or address has changed

New owner, purchased vehicle used

E V V

Same owner, additional driver who should receive product/safety updates

Vehicle Identification Number (required to process change)

Mr.

Mrs.

Ms.

Miss

Dr.

Effective date of this information

Mo.

Day

Year

First name

M.I.

Last name

Check here if address below is for company

Company name

Street address or P.O. Box

Apt. or suite number

City

– Home phone number

–

–

–

State

– Work phone number

–

Social Security Number (optional; for Toyota customer reference only)

– Zip code

Extension

This information is obtained solely for the use of Toyota Motor Sales, U.S.A., Inc. Toyota occasionally sends special promotional offers to registered owners. Check here if you prefer not to receive these offers. ■

If your name or address has changed or you purchased your Toyota as a used vehicle, please complete and mail the attached card, even if your warranty coverage has expired. This will enable Toyota to contact you with important product or safety updates concern- ing your vehicle. If the card is no longer attached, please call the Toyota Customer Assistance Center at (800) 331-4331.

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ’03MY CELICA U (L/O 0208)

SECTION 3

STARTING AND DRIVING Before starting the engine How to start the engine Tips for driving in various conditions Winter driving tips Dinghy towing Trailer towing How to save fuel and make your vehicle last longer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

148
148
149
150
151
152
157

147

2003 CELICA from Aug. ’02 Prod. (OM20809U)

Before starting the engine 1. Check the area around the vehicle be-

fore entering it.

2. Adjust seat position, seatback angle, seat cushion angle and steering wheel angle.

3. Adjust the inside and outside rear view

mirrors.

4. Lock both side doors. 5. Fasten seat belts.

’03MY CELICA U (L/O 0208)

How to start the engine— (a) Before cranking 1. Apply the parking brake firmly. 2. Turn off unnecessary lights and acces-

sories.

into neutral. Hold

3. Manual transmission: Press the clutch pedal to the floor and shift the trans- mission the clutch pedal to the floor until the engine is started. A starter safety device will pre- vent the starter from operating if the clutch pedal is not fully depressed. Automatic transmission: Put the se- lector lever in “P”. If you need to re- start the engine while the vehicle is moving, put the selector lever in “N”. A starter safety device will prevent the starter the selector lever is in any drive position.

from operating if

4. Automatic

transmission only: De- press the brake pedal and hold it to the floor until driving off.

(b) Starting the engine Before starting the engine, be sure to fol- low the instructions in “(a) Before crank- ing”. Normal starting procedure The multiport fuel injection system/sequen- tial multiport fuel injection system in your engine automatically controls the proper air−fuel mixture for starting. You can start a cold or hot engine as follows: 1. With your foot off the accelerator ped- al, crank the engine by turning the key to “START”. Release it when the en- gine starts.

2. After the engine runs for about 10 sec-

onds, you are ready to drive.

If the weather is below freezing, let the engine warm up for a few minutes before driving. If the engine stalls... Simply restart it, using the correct proce- dure given in normal starting. If the engine will not start... See “If your vehicle will not start” in Sec- tion 4.

148

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

NOTICE

z Do not crank for more than 30 sec- onds at a time. This may overheat the starter and wiring systems.

z Do not race a cold engine. z If the engine becomes difficult to start or stalls frequently, have the engine checked immediately.

Tips for driving in various conditions D Always slow down in gusty crosswinds. This will allow you much better control. D Drive slowly onto curbs and, if pos- sible, at a right angle. Avoid driving onto high, sharp−edged objects and other road hazards. Failure to do so can lead to severe tire damage result- ing in tire bursts. Drive slowly when passing over bumps or travelling on a bumpy road. Other- wise, the impact could cause severe damage to the tires and/or wheels.

they

D When parking on a hill, turn the front wheels until touch the curb so that the vehicle will not roll. Apply the parking brake, and place the transmis- sion in “P” (automatic) or in first or reverse (manual). If necessary, block the wheels.

D Washing your vehicle or driving through deep water may get the brakes wet. To see whether they are wet, check that there is no traffic near you, and then press the pedal lightly. If you do not feel a normal braking force, the brakes are probably wet. To dry them, drive the vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.

CAUTION

D Before driving off, make sure that the parking brake is fully released and reminder light is off.

the parking brake

D Do not

leave your vehicle unat- tended while the engine is running. D Do not rest your foot on the brake pedal while driving. It can cause dangerous overheating, needless wear, and poor fuel economy.

D To drive down a long or steep hill, reduce your speed and downshift. Remember, if you ride the brakes excessively, they may overheat and not work properly.

149

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

Winter driving tips Make sure you have a proper freeze protection of engine coolant. Your coolant must contain ethylene−glycol type coolant for a proper corrosion protec- tion of aluminum components. Use “Toyota Genuine Long Life Coolant” or equivalent. See Section 7−2 for details about coolant type selection.

NOTICE

Do not use alcohol type antifreeze or plain water alone.

When it is extremely cold, we recommend to use 60% solution for your Toyota, to provide protection down to about −50_C (−58_F). Do not use more than 70% solu- tion for better coolant performance. Check the condition of the battery and cables. Cold temperatures reduce the capacity of any battery, so it must be in top shape to provide enough power for winter start- ing. Section 7−3 tells you how to visually inspect the battery. Your Toyota dealer and most service stations will be pleased to check the level of charge.

Make sure the engine oil viscosity is suitable for the cold weather. See Section 7−2 for recommended viscos- ity. Leaving a heavy summer oil in your vehicle during winter months may cause harder starting. If you are not sure about which oil to use, call your Toyota deal- er—he will be pleased to help. Keep the door locks from freezing. Squirt lock de−icer or glycerine into the locks to keep them from freezing. To open a frozen lock, try heating the key before inserting it. Use a washer fluid containing an anti- freeze solution. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

D Be careful when accelerating, up- shifting, downshifting or braking on a slippery surface. Sudden accelera- tion or engine braking, could cause the vehicle to spin or skid.

tire dealer

D Do not drive in excess of the speed limit. Even if the legal speed limit permits it, do not drive over 140
km/h (85 mph) unless your vehicle has high−speed capability tires. Driving over 140 km/h (85 mph) may result in tire failure, loss of control and possible injury. Be sure to con- sult a to determine whether the tires on your vehicle are high−speed capability tires or not before driving at such speeds. D Do not continue normal driving when the brakes are wet. If they are wet, your vehicle will require a lon- ger stopping distance, and it may pull to one side when the brakes are applied. Also, the parking brake will not hold the vehicle securely.

150

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

Dinghy towing (with automatic transmission)

Dinghy towing (with manual transmission)

Your vehicle to be dinghy towed (with four wheels on the ground) behind a motorhome.

is not designed

Your vehicle can be dinghy towed (with four wheels on the ground) from the front behind a motorhome.

NOTICE

CAUTION

Do not tow your vehicle with four wheels on the ground. This may cause serious damage to your vehicle.

Dinghy towing requires special equip- ment and accessories. Please refer to your service outlet of the motorhome manufacture recommended equipment.

the

for

into

in and around

Do not use your parking brake when there is a possibility it could freeze. When parking, put the transmission into “P” (automatic) or first or reverse (manual) and block the rear wheels. Do not use the parking brake, or snow or water accumulated the freeze, parking brake mechanism may making it hard to release. Keep ice and snow from accumulating under the fenders. Ice and snow built up under your fenders can make steering difficult. During bad winter driving, stop and check under the fenders occasionally. Depending on where you are driving, we recommend you carry some emer- gency equipment. Some of the things you might put in the vehicle are tire chains, window scraper, bag of sand or salt, flares, small shovel, jumper cables, etc.

151

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

NOTICE

Dinghy towing does not eliminate the possibility of damage to your vehicle.

DINGHY TOWING TIPS Before dinghy towing, be sure to ob- serve the following in order to reduce the damage to your vehicle. 1. Put the shift lever in neutral. 2. Turn the ignition switch to the “ACC” position. Make sure the audio is turned off and any item is not plugged into the power outlet.

NOTICE

To avoid the locking of the steering wheel, turn the ignition switch to the “ACC” position.

3. Release the parking brake. After dinghy towing, let the engine idle for more than 3 minutes before driving the vehicle.

152

NOTICE

Do not tow your vehicle from the rear. This may cause serious damage to your vehicle.

vehicle. Towing

Trailer towing Your vehicle is designed primarily as a passenger−carrying trailer will have an adverse effect on handling, performance, braking, durability and driving economy (fuel consumption, etc.). Your safety and satisfaction depend on the proper use of correct equipment and cautious driving habits. For your safety and the safety of others, you must not overload your vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Ask your local further details before Toyota dealer towing. WEIGHT LIMITS Before towing, make sure the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all with- in the limits. The total trailer weight and tongue load can be measured with platform scales found at a highway weighing station, build- ing supply company, trucking company, junk yard, etc.

for

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

CAUTION

Total trailer weight

Tongue load

D The

total

trailer weight its cargo

(trailer weight plus load) must not exceed 907 kg (2000 lb.). Ex- ceeding this weight is dangerous.

D Trailer hitch assemblies have differ- ent weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capa- ble of towing a higher weight, the operator must determine the maxi- mum weight rating of the particular hitch assembly and never exceed the maximum weight rating speci- fied for the trailer−hitch. Exceeding the maximum weight rating set by the trailer hitch manufacturer can cause an accident resulting in seri- ous personal injuries.

Tongue load

Total trailer weight

100 = 9 to 11%

indicated on

D The gross vehicle weight must not the Gross Vehicle Weight exceed Rating (GVWR) the Certification Label. The gross ve- hicle weight is the sum of weights of the unloaded vehicle, driver, pas- sengers, luggage, hitch and trailer tongue includes the weight of any special equipment installed on your vehicle.

It also

load.

D The load on either the front or rear axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

153

2003 CELICA from Aug. ’02 Prod. (OM20809U)

D The trailer cargo

the

total

to 11% of

load should be distributed so that the tongue load is 9 trailer weight, not exceeding the maximum of 90 kg (200 lb.). Never load the trailer with more weight in the back than in the front. About 60% of the trailer load should be in the front half of the trailer and the remaining 40% in the rear.

HITCHES D Use only a hitch which

recom- mended by the hitch manufacturer and conforms to the total trailer weight re- quirement.

is

D Follow the directions supplied by the hitch manufacturer, and bolt the hitch securely to the rear bumper. Lubricate the hitch ball with a light coat of grease.

trailer

D Toyota recommends removing the trail- er hitch whenever you are not towing to reduce the possibility of additional damage caused by the hitch if your vehicle is struck from behind. After the hitch, seal any mounting holes in the vehicle body to prevent entry of pollutants such as ex- haust fumes, dirt, water, etc.

removing

154

’03MY CELICA U (L/O 0208)

NOTICE

CAUTION

Do not use axle−mounted hitches as they can cause damage to the axle housing, wheel bearings, wheels or tires. Also, never install a hitch which may interfere with the normal function of an Energy Absorbing Bumper.

BRAKES AND SAFETY CHAINS D Toyota

recommends

trailers with brakes that conform to any applica- ble federal and state/provincial regu- lations.

D A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under to prevent the tongue from dropping to the ground in case it becomes dam- aged or separated. For correct safety chain procedures, follow the hitch or trailer manufacturer’s recommenda- tions.

tongue

trailer

the

D If the total trailer weight exceeds 453 kg (1000 lb.), trailer brakes are required.

D Never tap

into your vehicle’s hy- draulic system as it would lower its braking effectiveness.

D Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering over into another lane.

TIRES D Ensure

that your vehicle’s

tires are properly inflated. See Section 7−2 and Section 8 for instructions.

D The trailer tires should be inflated to the pressure recommended by the trail- er manufacturer in respect to the total trailer weight.

2003 CELICA from Aug. ’02 Prod. (OM20809U)

local

local

TRAILER LIGHTS D Trailer lights must comply with federal, regulations. state/provincial and See your recreational vehicle dealer or rental agency for the correct type of wiring and relays for your trail- er. Check for correct operation of the turn signals and stop lights each time you hitch up. Direct splicing may dam- age your vehicle’s electrical system and cause a malfunction of your lights.

BREAK−IN SCHEDULE D Toyota recommends

that you do not tow a trailer with a new vehicle or a vehicle with any new power train com- ponent (engine, transmission, differen- tial, wheel bearing, etc.) for the first 800 km (500 miles) of driving.

MAINTENANCE D If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. For this informa- tion, please the scheduled maintenance information in the “Sched- uled Maintenance Guide” or “Owner’s Manual Supplement”.

refer

to

D Retighten all fixing bolts of the towing ball and bracket after approximately 1000 km (600 miles) of trailer driving.

’03MY CELICA U (L/O 0208)

PRE−TOWING SAFETY CHECK D Check that your vehicle remains a lev- el when a loaded or unloaded trailer is hitched. Do not drive if the vehicle has an abnormal nose−up or nose−down condition, and check improper tongue load, overload, worn suspension or other possible causes.

for

D Make sure the trailer cargo is securely

loaded so that it can not shift.

D Check that your rear view mirrors con- form to any applicable federal, state/ provincial or local regulations. If not, install the rear view mirrors required for towing purpose.

TRAILER TOWING TIPS When towing a trailer, your vehicle will handle differently than when not tow- ing. The three main causes of vehicle− trailer accidents are driver error, exces- sive speed and improper trailer loading. Keep these in mind when towing: D Before starting out, check operation of the lights and all vehicle−trailer connec- tions. After driving a short distance, stop and recheck the lights and con- nections. Before actually towing a trail- er, practice turning, stopping and back- ing with a trailer in an area away from traffic until you learn the feel.

D Backing with a trailer is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This pro- cedure that when backing without a trailer.) Also, just turn the steering wheel a little at time, avoiding sharp or prolonged turning. Have someone guide you when backing to reduce the risk of an acci- dent.

is generally opposite

to

increased when

D Because stopping distance may be in- vehicle−to−vehicle distance creased, should be towing a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle and trailer length between you and the ve- hicle ahead. Avoid sudden braking as you may skid, resulting in jackknifing and loss of control. This is especially true on wet or slippery surfaces.

D Avoid jerky starts or sudden accelera- tion. If your vehicle has a manual transmission, prevent excessive clutch slippage by keeping engine rpm low and not racing the engine. Always start out in first gear.

155

2003 CELICA from Aug. ’02 Prod. (OM20809U)

D Avoid jerky steering and sharp turns. The trailer could hit your vehicle in a tight turn. Slow down before making a turn to avoid the necessity of sudden braking.

D Remember that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Therefore, compensate for this by making a turning radius with your vehicle.

than normal

larger

D Crosswinds and rough roads will ad- versely affect handling of your vehicle and trailer, causing sway. Pay attention to the rear from time to time to pre- pare yourself for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying happens, firmly grip the steering wheel and immediately but gradually. Never increase speed. Steer straight ahead. If you make no extreme correction with the steering or brakes, the vehicle and trailer will stabilize.

reduce speed

D Be careful when passing other ve- hicles. Passing requires considerable distance. After passing a vehicle, do not forget the length of your trailer and be sure you have plenty of room be- fore changing lanes.

156

’03MY CELICA U (L/O 0208)

4. Apply the parking brake firmly. 5. Shift into first or reverse (manual) or “P” (automatic) and turn off the engine. When restarting out after parking on a slope: 1. With the transmission in “P” position the clutch pedal de- the engine. transmission, be the brake pedal de-

(automatic) or pressed (With an automatic sure pressed.)

(manual), start

to keep

2. Shift into gear. 3. Release the parking brake (also foot brake on automatic transmission ve- hicles) and slowly pull or back away from the wheel blocks. Stop and apply your brakes.

4. Have someone retrieve the blocks.

D In order to maintain engine braking effi- ciency do not use fifth gear (5−speed manual gear (6−speed manual transmission) or over- drive (automatic transmission).

transmission),

sixth

(at

D Because of the added load of the trail- er, your vehicle’s engine may overheat on hot days temperatures over 30_C [85_F]) when going up a long or steep grade with a trailer. If the engine coolant indicates overheating, immediately turn off the air conditioning (if in use), pull off the road and stop in a safe spot. Refer to “If your vehicle overheats” in Section 4.

temperature gauge

D Always place wheel blocks under both the vehicle and trailer wheels when parking. Apply the parking brake firmly. Put the transmission in “P” (automatic) or in first or reverse (manual). Avoid parking on a slope with a trailer, but if it cannot be avoided, do so only after performing the following:

1. Apply the brakes and hold. 2. Have someone place wheel blocks un- der both the vehicle and trailer wheels. 3. When the wheel blocks are in place, the

release your brakes slowly until blocks absorb the load.

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

CAUTION

towing speed

D Do not exceed 72 km/h (45 mph) or the posted limit, whichever is lower. Because insta- bility (swaying) of a towing vehicle− trailer in- creases as the speed increases, ex- ceeding 72 km/h (45 mph) may cause loss of control.

combination

usually

D Slow down and downshift before descending steep or long downhill grades. Do not make sudden down- shifts.

long or

D Avoid holding the brake pedal down too frequently. This could cause the brakes to overheat and result in reduced braking effi- ciency.

too

How to save fuel and make your vehicle last longer Improving fuel economy is easy—just take it easy. It will help make your vehicle last longer, too. Here are some specific tips on how to save money on both fuel and repairs: D Keep your tires inflated at the cor- rect pressure. Underinflation causes tire wear and wastes fuel. See Section 7−2 for instructions.

D Do not carry unneeded weight

in your vehicle. Excess weight puts a heavier the engine, causing greater fuel consumption.

load on

D Avoid lengthy warm−up idling. Once the engine is running smoothly, begin driving—but gently. Remember, howev- er, that on cold winter days this may take a little longer.

D Keep

the automatic

transmission overdrive turned on when engine braking is not required. Driving with the overdrive off will reduce the fuel economy. (For details, see “Automatic transmission” in Section 1−6.)

D Accelerate

slowly

smoothly. Avoid jackrabbit starts. Get into high gear as quickly as possible.

and

D Avoid long engine idling. If you have a long wait and you are not in traffic, it is better to turn off the engine and start again later.

D Avoid engine

lugging or over−rev- ving. Use a gear position suitable for the road on which you are travelling.

D Avoid continuous speeding up and slowing down. Stop−and−go driving wastes fuel.

D Avoid unnecessary stopping and braking. Maintain a steady pace. Try to time the traffic signals so you only need to stop as little as possible or take advantage of through streets to avoid traffic lights. Keep a proper dis- tance from other vehicles to avoid sud- den braking. This will also reduce wear on your brakes.

D Avoid heavy traffic or traffic

whenever possible.

jams

D Do not rest your foot on the clutch or brake pedal. This causes premature wear, overheating and poor fuel econo- my.

D Maintain a moderate speed on high- ways. The faster you drive, the greater the fuel consumption. By reducing your speed, you will cut down on fuel con- sumption.

157

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

CAUTION

Never turn off the engine to coast down hills. Your power steering and brake booster will not function with- out the emission control system operates properly only when the engine is run- ning.

the engine running. Also,

the

D Keep

front wheels

in proper alignment. Avoid hitting the curb and slow down on rough roads. Improper alignment not only causes faster tire wear but also puts an extra load on the engine, which, in turn, wastes fuel. D Keep the bottom of your vehicle free from mud, etc. This not only lessens weight but also helps prevent corro- sion.

D Keep your vehicle tuned−up and in top shape. A dirty air cleaner, improp- er valve clearance, dirty plugs, dirty oil and grease, brakes not adjusted, etc. all lower engine performance and con- tribute to poor fuel economy. For longer life of all parts and lower operating costs, keep all maintenance work on schedule, and if you often drive under severe conditions, see that your vehicle frequent maintenance. receives more (For scheduled maintenance informa- tion, please refer the “Scheduled Maintenance Guide” or “Owner’s Manu- al Supplement”.)

to

158

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

SECTION 4

IN CASE OF AN EMERGENCY If your vehicle will not start If your engine stalls while driving If you cannot increase the engine speed If your vehicle overheats If you have a flat tire If your vehicle becomes stuck If your vehicle needs to be towed If you cannot shift automatic transmission selector lever If you lose your keys If you lose your wireless remote control transmitter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160
163
163
164
165
175
175
178
179
179

159

2003 CELICA from Aug. ’02 Prod. (OM20809U)

If your vehicle will not start— (a) Simple checks Before making these checks, make sure you have followed the correct starting pro- cedure given in “How to start the engine” in Section 3 and that you have sufficient fuel. If the engine is not turning over or is turning over too slowly— 1. Check the battery

terminals are

that

tight and clean.

2. If the battery terminals are O.K., switch

on the interior light.

3. If the light

is out, dim or goes out when the starter is cranked, the battery is discharged. You may try jump start- ing. See “(c) Jump starting” for further instructions.

If the light is O.K., but the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop.

NOTICE

Do not pull− or push−start the vehicle. It may damage the vehicle or cause a collision when the engine starts. Also the three−way catalytic converter may overheat and become a fire hazard.

160

’03MY CELICA U (L/O 0208)

If the engine turns over at its normal speed but will not start— 1. Turn ignition key

the

to

“ACC” or the engine

“LOCK” and again.

try starting

2. If the engine will not start, the engine may be flooded because of repeated cranking. See “(b) Starting a flooded engine” for further instructions.

3. If the engine still will not start, it needs repair. Call a Toyota

adjustment or dealer or qualified repair shop.

(b) Starting a flooded engine If the engine will not start, your engine may be flooded because of repeated cranking. If this happens, turn the key to “START” with the accelerator pedal held down. Keep the key and accelerator pedal so for 15 seconds and release them. Then try starting the engine with your foot off the accelerator pedal. If the engine does not start after 15 se- conds of cranking, release the key, wait a few minutes and try again. If the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop for assistance.

NOTICE

Do not crank for more than 30 seconds at a time. This may overheat the starter and wiring systems.

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

(c) Jump starting To avoid serious personal injury and damage to your vehicle which might re- sult from battery explosion, acid burns, electrical burns, or damaged electronic components, these instructions must be followed precisely. If you are unsure about how to follow this procedure, we strongly that you seek the help of a competent me- chanic or towing service.

recommend

CAUTION

D Batteries

contain

sulfuric

acid which is poisonous and corrosive. Wear protective safety glasses when jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.

D If you should accidentally get acid on yourself or in your eyes, remove any contaminated clothing and flush the affected area with water imme- diately. Then get immediate medical attention. If possible, continue to apply water with a sponge or cloth while en route to the medical office.

D The gas normally produced by a battery will explode if a flame or spark is brought near. Use only standardized jumper cables and do not smoke or light a match while jump starting.

D Warning: Battery posts,

terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause reproductive harm. Wash hands after handling.

cancer

and

NOTICE

The battery used for boosting must be 12 V. Do not jump start unless you are sure that the booster battery is correct.

JUMP STARTING PROCEDURE 1. If

the booster battery

installed in another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories.

is

2. If required, remove all the vent plugs from the booster and discharged batter- ies. Lay a cloth over the open vents on the batteries. (This helps reduce the explosion hazard, personal injuries and burns.)

3. If the engine in the vehicle with the booster battery is not running, start it and let it run for a few minutes. During jump starting, run the engine at about 2000 rpm with the accelerator pedal lightly depressed.

161

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

Discharged battery

Jumper cable

Booster battery

Positive terminal (“+” mark)

Jumper cable

Positive terminal (“+” mark)

4. Make the cable connections in the or-

der a, b, c, d. a. Connect the clamp of the positive (red) jumper cable to the positive (+) terminal on the discharged battery. b. Connect the clamp at the other end of the positive (red) jumper cable to the positive (+) terminal on the booster battery.

Discharged battery

Negative terminal (“−” mark)

Booster battery

c. Connect the clamp of the negative (black) jumper cable to the negative (–) terminal on the booster battery. d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, unpainted, metallic point of the vehicle with the discharged battery. The recommended connecting point is shown in the following illustration:

Connecting point

Do not connect the cable to or near any part that moves when the engine is cranked.

CAUTION

the connections,

to When making avoid serious injury, do not lean over the battery or accidentally the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.

let

162

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

5. Start your engine in the normal way. After starting, run it at about 2000 rpm for several minutes with the accelerator pedal lightly depressed.

6. Carefully disconnect the cables in the exact reverse order: the negative cable and then the positive cable.

7. Carefully dispose of the battery cover cloths—they may now contain sulfuric acid.

8. If removed, replace all the battery vent

plugs.

If the cause of your battery discharging is not apparent (for example, lights left on), you should have it checked at your Toyota dealer.

If your engine stalls while driving If your engine stalls while driving... 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Turn

ignition key

the

to try starting

“ACC” or the engine

“LOCK”, and again.

If the engine will not start, see “If your vehicle will not start” in this section.

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

If you cannot increase the engine speed (2ZZ−GE engine) If the engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in your electronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key to “ACC” or “LOCK” position.

turned

is

CAUTION

Be especially careful to prevent erro- neous pedal operation.

163

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

CAUTION

Do not attempt to touch the coolant reservoir tank when the engine and radiator are hot. Serious injury could result fluid and steam blown out under pressure.

from scalding hot

If your vehicle overheats If your engine coolant temperature gauge indicates overheating, if you ex- perience a loss of power, or if you hear a loud knocking or pinging noise, the engine has probably overheated. You should follow this procedure... 1. Pull safely off the road, stop the ve- turn on your emergency hicle and flashers. Put the transmission in “P” (automatic) or neutral (manual) and ap- ply the parking brake. Turn off the air conditioning if it is being used.

2. If coolant or steam is boiling out of the radiator or reservoir, stop the engine. Wait until the steam subsides before opening the hood. If there is no coolant boiling over or steam, leave the engine running and make sure the electric cooling fan is operating. If it is not, turn the ignition off.

CAUTION

injury, keep To help avoid personal the hood closed until there is no steam. Escaping steam or coolant is a sign of very high pressure.

3. Look for obvious coolant leaks from the radiator, hoses, and under the vehicle. However, note that water draining from the air conditioning is normal if it has been used.

CAUTION

the engine

When is running, keep hands and clothing away from the moving fan and engine drive belts.

4. If the coolant is leaking, stop the en- gine immediately. Call a Toyota dealer for assistance.

5. If there are no obvious leaks, check

the coolant reservoir. If it is dry, call a Toyota dealer for assistance as soon as possible. If there is enough coolant in the reser- voir, again check the coolant level in the reservoir after the engine coolant temperature has cooled to normal. Seri- ous coolant loss indicates a leak in the system. You should have it checked as soon as possible at you Toyota dealer.

164

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

If you have a flat tire— 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from the traffic. Avoid stopping on the center divider of a highway. Park on a level spot with firm ground.

2. Stop

the engine and

turn on your

emergency flashers.

3. Firmly set the parking brake and put the transmission in “P” (automatic) or reverse (manual).

4. Have everyone get out of the vehicle

on the side away from traffic.

5. Read oughly.

the

following

instructions

thor-

CAUTION

When jacking, be sure to observe the following to reduce the possibility of personal injury: D Follow jacking instructions. D Do not put any part of your body under the vehicle supported by the jack. Otherwise, personal injury may occur.

D Do not start or run the engine while is supported by the

your vehicle jack.

D Stop the vehicle on a

the transmission

level firm ground, firmly set the parking brake and put in “P” (automatic) or (manual). Block the wheel diagonally opposite to the one being changed if neces- sary.

reverse

NOTICE

Do not continue driving with a de- flated tire. Driving even a short dis- tance can damage a tire and wheel beyond repair.

D Make sure to set the jack properly in the jack point. Raising the ve- hicle with improperly posi- tioned will damage the vehicle or may allow the vehicle to fall off the jack and cause personal injury.

jack

D Never get under the vehicle when the vehicle is supported by the jack alone.

D Use the jack only for lifting your

vehicle during wheel changing.

D Do not raise the vehicle with some-

one in the vehicle.

D When raising the vehicle, do not place any objects on top of or un- derneath the jack.

D Raise the vehicle only high enough

to remove and change the tire.

165

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

Type A

Type B

Spare tire with turning direction indica- tors (some models) The spare tires with turning direction indicators are directional and intended to be used so that they turn in the same direction as the turning direction indicators. Installing the wheel on the driver side of the vehicle will not affect tire performance. If the spare tire is used on the driver side it should be used only of the vehicle, temporarily and then replaced with the correct one.

166

The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) depending on road conditions and your driving habits. When tread wear indicators appear on the tire, replace the tire. See also the tire section in Section 7−2
for details on the tread wear indicators and other service information.

CAUTION

D The compact spare

tire was de- signed especially for your Toyota. Do not use it on any other vehicle. D Do not use more than one compact

spare tire at the same time.

D The pressure for the compact spare tire must be 420 kPa (4.2 kgf/cm2
or bar, 60 psi).

D Do not exceed 80 km/h (50 mph) the compact

when driving with spare tire.

D The standard

tire should be re- paired and replaced as soon as possible.

D Avoid sudden acceleration, sudden deceleration and sharp turns with the compact spare tire.

Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by the distinctive wheel design and color and special wording “TEMPORARY USE ONLY” molded into the side wall of the tire. The compact spare tire saves space in your trunk or luggage compartment, and its improve fuel economy and permits easier installation in case of a flat tire.

lighter weight helps

to

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

—Required tools and spare tire

NOTICE

is the compact spare

reduced Your ground clearance when is tire installed so avoid driving over ob- stacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not attempt to go through an automatic car wash as the vehicle may get caught, resulting in damage.

tools and spare

the required

1. Get tire. 1 Jack 2 Wheel nut wrench 3 Spare tire 4 Jack handle

To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their stor- age locations.

With a compact spare tire

Without a compact spare tire

167

2003 CELICA from Aug. ’02 Prod. (OM20809U)

’03MY CELICA U (L/O 0208)

2. Twist the jack head clockwise and pull

out the jack.

To remove the jack: 1. Turn the jack joint by hand until the

jack becomes free.

CAUTION

When removing the jack, be careful not to injure your hands with the edge of the trim.

To store the jack, put the jack base on the fitting place. Turn the joint until the jack upper side fits securely with the pro- trusion of the carrier. This prevents the jack from flying forward during a collision or sudden braking.