2001 Toyota Camry Owners Manual

If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the sur- faces. An indicator light will illuminate to indicate the defogger is operating. On some models, heater panels in the outside rear view mirrors will also quickly clear the surfaces. Push the switch once again to turn the defogger off. The system will automatically shut off af- ter the defogger has operated about 15
minutes.

CAUTION

Since the mirror surfaces can get hot keep your hands off them when the defogger switch is on.

turn

Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow.

2001 MY CAMRY (OM33528U)

81

’01Camry_U (L/O 0009)

82

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge Engine coolant temperature gauge Tachometer Odometer and two trip meters Service reminder indicators and warning buzzers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

84
84
85
85
86

2001 MY CAMRY (OM33528U)

83

’01Camry_U (L/O 0009)

Fuel gauge

Engine coolant temperature gauge

On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

Low fuel level warning light

the

The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. This fuel gauge has a non−return type needle which remains at the last indicated position when the ignition switch is turned off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible.

84

2001 MY CAMRY (OM33528U)

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high

speed driving.

’01Camry_U (L/O 0009)

Tachometer

Odometer and two trip meters

D Idling for a long period with the air conditioning on in stop−and−go traffic.

D Towing a trailer.

NOTICE

z Do not remove the thermostat

in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.

z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” in Section 4.

The tachometer indicates engine speed in thousands of rpm ( revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.

NOTICE

Do not let the indicator needle get into the red zone. This may cause severe engine damage.

This meter displays the odometer and two trip meters. 1. Odometer—Shows

total distance

the

the vehicle has been driven.

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

2001 MY CAMRY (OM33528U)

85

3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

to

’01Camry_U (L/O 0009)

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

If the indicator or buzzer comes on...

Do this.

or

If parking brake is off, stop immediately and contact Toyota dealer.

Fasten seat belt.

(f)

(g)

Stop and check.

Take vehicle to Toyota dealer.

or

(indicator and buzzer)

Stop and check.

(h)

Close all doors.

(a)

(b)

(c)

(d)

Take vehicle to Toyota dealer.

(i)

(j)

Replace bulb.

Take vehicle to Toyota dealer immediately.

(e)

Low fuel level warning light

Fill up tank.

86

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

If the indicator or buzzer comes on...

Do this.

(k)

(l)

Add washer fluid.

Take vehicle to Toyota dealer.

(m)

Key reminder buzzer

Remove key.

(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... D When the brake fluid level is low...

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

Have your vehicle checked at your Toyota dealer in the following case: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.

CAUTION

If the light does not turn off even after the parking brake is released while the engine is running, immedi- ately stop your vehicle at a safe place and contact your Toyota dealer. In this case, the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop.

(b) Seat Belt Reminder Light and Buzz-

er

to

remind you

light and buzzer

This buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, light and buzzer come on if the driver’s seat belt is not fastened. Unless the belt, the light stays on and the buzzer stops after about 4 to 8 seconds.

the reminder

the driver

fastens

2001 MY CAMRY (OM33528U)

87

’01Camry_U (L/O 0009)

(c) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.

NOTICE

Do not continue driving if the engine drive belt is broken or loose.

lamp comes on

(d) Malfunction Indicator Lamp This the cases. a. The

fuel

in

tank

is completely empty. (See “Fuel gauge” in this section for instructions.)

following

b. The fuel tank cap is not tightened se- curely. (See “Fuel tank cap” in Section 1−2 for instructions.)

c. There is a problem somewhere in your engine or automatic transmission elec- trical system.

If it comes on while you are driving in case c, have your vehicle checked/re- paired by your Toyota dealer as soon as possible. (e) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.

(f) Low Oil Pressure Warning Light This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.

light may occasionally

low. It

NOTICE

Do not drive the warning light on—even for one block. It may ruin the engine.

the vehicle with

88

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

(g) “ABS” Warning Light The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system works properly, the light turns off after a few seconds. There- after, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system and the traction control system do not operate, but the brake system still operates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem. (h) Open Door Warning Light This light remains on until all the doors are completely closed. (i) Rear Light Failure Warning Light If this light comes on when the headlight switch is turned on (at the first or second clickstop), it indicates that one or more of the tail lights are burned out. If it comes on when the brake pedal is depressed, one or more stop lights are burned out. Have defective bulbs replaced as soon as possible.

light system monitors

(j) SRS Warning Light This light will come on when the igni- tion key is turned to the “ACC” or “ON” position. After about 6 seconds, the light will go off. This means the systems of the airbag and front seat belt pretensioner are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side airbag sensors, front seat belt pretensioner assemblies, inflators, warning light, interconnecting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ACC” or “ON” position or remains on.

D The light comes on or flashes while

driving.

2001 MY CAMRY (OM33528U)

89

’01Camry_U (L/O 0009)

light

SERVICE

CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.

and

The open door warning come on.

light should

3. Close the door.

The open door warning light should go off.

4. Turn the ignition key to “ACC”.

The SRS warning light should come on. It goes off after about 6 seconds.

5. Turn the ignition key to “ON”, but do

not start the engine. All the service reminder indicators ex- cept the open door warning light and SRS warning light should come on. The “ABS” warning light, “TRAC OFF” and slip indicator lights go off after a few seconds.

If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

(k) Low Windshield Washer Fluid Level

Warning Light

The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” in Section 7−3.) (l) “TRAC OFF” Indicator/Warning Light This light comes on when the ignition key is turned to “ON”, and will go off after a few seconds. This means that the system is operating properly. If one of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light remains on more than a few is

ignition switch

the

seconds after turned on.

D The light comes on while driving even is not

“TRAC OFF” switch

the if pushed.

D The light flashes. (m) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.

90

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

SECTION 1− 6

OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake

Ignition switch with steering lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

92

Automatic transmission

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

93

Manual transmission

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

97

Parking brake

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98

Cruise control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98

2001 MY CAMRY (OM33528U)

91

’01Camry_U (L/O 0009)

Ignition switch with steering lock

NOTICE

leave the key

in the “ON” Do not position if the engine is not running. The battery will discharge and the ignition could be damaged.

You must push in the key to turn the key from “ACC” to the “LOCK” position. On vehicles with an automatic transmission, the selector lever must be put in the “P” position before pushing the key. Vehicles with engine immobiliser system— Once you remove the key, the engine im- mobiliser system is automatically set. (See “Engine in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.

immobiliser system”

CAUTION

For manual transmission: Never remove the key when the ve- hicle is moving, as this will lock the steering wheel and result in loss of steering control.

2001 MY CAMRY (OM33528U)

“START”—Starter motor on. The key will return to the “ON” position when released. For starting tips, see Section 3. “ON”—Engine on and all accessories on. This is the normal driving position. “ACC”—Accessories such as the radio operate, but the engine is off. the “ACC” or If you “LOCK” position and open the driver’s door, a buzzer will remind you to remove the key. “LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. 92

the key

leave

in

’01Camry_U (L/O 0009)

Automatic transmission

Lock release button To prevent misshifting

Selector lever

With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in “ON” position.)

Overdrive switch

Shift while holding the lock release button in.

Shift normally.

Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” position and the lock re- lease button depressed). (a) Selector lever The shift position is also displayed on the instrument cluster. P: Parking, engine starting and

key removal

R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking

2001 MY CAMRY (OM33528U)

93

’01Camry_U (L/O 0009)

Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.

2. With your foot holding down the brake

pedal, shift the selector lever to “D”.

When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.

temperature

low,

is

CAUTION

Never put your foot on the accelera- tor pedal while shifting.

2001 MY CAMRY (OM33528U)

3. Release the parking brake and brake the accelerator pedal

pedal. Depress slowly for smooth starting.

(d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to third gear.

. . . . . . . . .

D Shift into the “2” position. The trans- mission will downshift to second gear when the vehicle speed drops down to or lower than the following speed, and stronger engine braking will be en- abled. 5S−FE engine 1MZ−FE engine

112 km/h (69 mph) 122 km/h (75 mph) D Shift into the “L” position. The trans- mission will downshift first gear when the vehicle speed drops down to or lower than the following speed, and maximum engine braking will be en- abled. 5S−FE engine 1MZ−FE engine

50 km/h (31 mph) 54 km/h (33 mph)

. . . . . . . . .

to

(b) Overdrive switch You can select either third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will be on automatically.

for better

94

’01Camry_U (L/O 0009)

Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking is not enabled because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section.

NOTICE

z Be careful not to over−rev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:

(g) Parking 1. Bring the vehicle to a complete stop. 2. Pull the parking brake lever up fully to

securely apply the parking brake.

3. With

the brake pedal pressed down, shift the selector lever to the “P” posi- tion.

CAUTION

Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.

surface. Abrupt

(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in first gear and automatically shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.

“2” “L”

. . . . . . . . . . . . . . . . . . . . . . . .

125 km/h (77 mph) 69 km/h (42 mph) z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.

(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.

NOTICE

Never shift into reverse while the ve- hicle is moving.

CAUTION

Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.

(h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.

D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.

2001 MY CAMRY (OM33528U)

95

’01Camry_U (L/O 0009)

CAUTION

Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

NOTICE

Do not hold the vehicle on an up- grade with the accelerator pedal. It can cause the transmission to over- heat. Always use the brake pedal or parking brake.

(i) Rocking your vehicle if stuck

CAUTION

If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock your vehicle free by moving it forward and backward. Do not attempt this procedure if people or objects are anywhere near the ve- hicle. During the rocking operation the vehicle may suddenly move for- ward or backward as it becomes un- stuck, causing injury or damage to nearby people or objects.

NOTICE

z If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

(j)

If you cannot shift the selector le- ver out of “P” position

If you cannot shift the selector lever from “P” position even though the brake pedal is depressed, use the shift lock override button. For instructions, see “If you cannot shift automatic transmission selector lever” in Section 4.

to

the

If you rock your vehicle, observe the following precautions to prevent dam- age transmission and other parts. z Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.

z Do not race the engine and avoid

spinning the wheels.

96

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

Manual transmission

is conventional as

The shift pattern shown above. Press the clutch pedal down fully while shifting, and then release it slowly. Do not rest your foot on the pedal while driving, because it will cause clutch trouble. And do not use the clutch to hold the vehicle when stopped on an uphill grade—use the parking brake. Recommended shifting speeds The transmission is fully synchronized and upshifting or downshifting is easy.

the best compromise between

For fuel economy and vehicle performance, you should upshift or downshift at the following speeds:

gear

1 to 2 or 2 to 1
2 to 3 or 3 to 2
3 to 4 or 4 to 3
4 to 5 or 5 to 4

km/h 24
40
64
72

(mph) (15) (25) (40) (45)

Downshift to the appropriate gear if accel- eration is needed when you are cruising below the above downshifting speeds. Upshifting too soon or downshifting too late will cause lugging, and possibly ping- ing. Regularly revving the engine to maxi- mum speed in each gear will cause ex- cessive engine wear and high fuel consumption. Maximum allowable speeds To get on a highway or to pass slower traffic, maximum acceleration may be nec- essary. Make sure you observe the follow- ing maximum allowable speeds in each gear:

gear

km/h 52
93
147

(mph) (32) (57) (91)

NOTICE

Do not downshift faster speed for the next lower gear.

if you are going the maximum allowable

than

Good driving practice D If it is difficult to shift into reverse, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

D When towing a trailer, in order to main- tain engine braking efficiency, do not use the fifth gear.

CAUTION

Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.

surface. Abrupt

NOTICE

Make sure the vehicle is completely stopped before shifting into reverse.

2001 MY CAMRY (OM33528U)

97

’01Camry_U (L/O 0009)

Parking brake

Type A

Type B

98

it while setting

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Pull up the lever. For better hold- ing power, first depress the brake pedal and hold the parking brake. To release: Pull up the lever slightly (1), press the lock release button (2), and low- er (3). To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

Cruise control The cruise control allows you to cruise the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control.

CAUTION

D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration.

CAUTION

For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overrev- ving.

CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di-

rection and releasing it.

b. Depressing the brake pedal. c. Depressing

the clutch pedal (manual

transmission).

If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out. If the vehicle speed drops 16 km/h (10
mph) below the preset speed,the preset speed will also automatically cancel out. 99

SETTING AT A DESIRED SPEED On vehicles with automatic transmission, the transmission must be in “D” before you set the cruise control speed. Bring your vehicle to the desired speed, push the lever down in the “SET/COAST” direction and release it. This sets the ve- hicle at that speed. If the speed is not satisfactory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your foot off the accelerator pedal.

2001 MY CAMRY (OM33528U)

TURNING ON THE SYSTEM To operate the cruise control, press the “CRUISE ON−OFF” button. This turns the system on. The the instrument panel shows that you can now set the vehicle at a desired cruising speed. Another press will turn the system completely off.

indicator

light

in

CAUTION

To avoid accidental cruise control en- gagement, keep the “CRUISE ON− OFF” switch off when not using the cruise control.

’01Camry_U (L/O 0009)

D The indicator light does not come on. D The indicator light flashes again. D The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESETTING TO A FASTER SPEED Push the lever up in the “RES/ACC” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “SET/COAST” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “SET/COAST” direction and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “SET/COAST” direction.

If you use

lever or by depressing

On vehicles with automatic transmission, even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled. RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise control, press the “CRUISE ON− OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system.

“CRUISE”

indicator

light

the

in

100

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Car audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

102
103
124

2001 MY CAMRY (OM33528U)

101

’01Camry_U (L/O 0009)

Reference

Type 1: AM·FM ETR radio/cassette player/ compact disc player (with compact disc auto changer controller)

Type 2: AM·FM ETR radio/cassette player/ compact disc player (with compact disc auto changer controller)

Type 3: AM·FM ETR radio/cassette player/ compact disc auto changer

102

2001 MY CAMRY (OM33528U)

“AM”,

“TAPE”,

“FM1·2”,

to turn on that

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” or “VOL/POWER” to turn the audio system on and off. Push “DISC” pushing “PWR·VOL” or “VOL/POWER”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “CD” or “DISC” if the system is already on but you want to switch from one function to anoth- er.

“CD” or function without

“FM1·2”,

“TAPE”,

“AM”,

’01Camry_U (L/O 0009)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA

NOTICE

Attaching the film (especially conduc- tive or metallic the rear glass will noticeably reduce the sensi- tivity of the radio.

type) on

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

2001 MY CAMRY (OM33528U)

103

’01Camry_U (L/O 0009)

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again. On models with the compact disc auto changer, next disc will be played from track 1.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

The player is intended for use with 12 cm (5 in.) discs only.

104

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

—Controls and features "Type 1

Details of specific buttons, controls and features are described in the alphabetical listing that follows.

2001 MY CAMRY (OM33528U)

105

’01Camry_U (L/O 0009)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

106

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

time you push “CD”,

CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.

inserted up−side down. Clean

loaded

inside

it the

is

If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”.

/ MODE”

/ MODE”

to adjust

low−pitch

is used

range

range

from

from

tone

the

the

to adjust

is also used

the display. Then

Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAD” appears on turn to adjust the front/rear balance. The display will show the “FAD−F7” to “FAD−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”.

the display. Then

the knob

the knob

range

range

from

from

the

2001 MY CAMRY (OM33528U)

107

’01Camry_U (L/O 0009)

B NR∗

DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button.

If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: ” Quickly push and release “ will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again.

listen

the

”. “

to

in the

Compact disc auto changer only— To randomly play all the tracks magazine: ” until you hear a Push and hold “ ” will appear on the dis- beep. “ play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again. RPT (Repeat) Cassette Player ” while the track is playing. Push “ ” will appear on the display. When “ the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

108

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: ” while the Quickly push and release “ track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: ” until you hear a Push and hold “ beep. “ ” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pres- et station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 se- conds, and then scan again. To select a station, push “SCAN” again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push the display “ and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning.

·SCAN” will appear on

“SCAN” again.

If

2001 MY CAMRY (OM33528U)

109

’01Camry_U (L/O 0009)

the seek mode,

the radio finds and the next station up or down the

SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

110

2001 MY CAMRY (OM33528U)

TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

’01Camry_U (L/O 0009)

"Type 2

Details of specific buttons, controls and features are described in the alphabetical listing that follows.

2001 MY CAMRY (OM33528U)

111

’01Camry_U (L/O 0009)

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

112

2001 MY CAMRY (OM33528U)

’01Camry_U (L/O 0009)

the

the

from

from

range

range

For front/rear adjustment, push “AUDIO” repeatedly until “FAD” appears on the dis- play. Then turn the knob to adjust the front/rear balance. The display will show “FAD−F7” to “FAD−R7”. For left/right adjustment, push “AUDIO” re- peatedly until “BAL” appears on the dis- play. Then turn the knob to adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. DISC (Compact Disc) Push “DISC” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “DISC”. In both cases, a disc must alrea- dy be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each time you push “DISC”, the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.

inserted up−side down. Clean

If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was