2010 Subaru Tribeca Owners Manual

soon as you find them.

Check the interior of the vehicle for water and dirt accumulation under the floor mats because that could cause corrosion. Occasionally check under the mats to make sure the area is dry.

Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated garage. In such a garage, corrosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.

If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, and hood latch should be inspected and lubricated periodically.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Cleaning the interior

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. (Do not use organic solvents.)

& Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft blush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and luke- warm water then dry thoroughly.

the stain does not come out,

try a If commercially-available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instruc- tions. NOTE When cleaning the seat, do not use benzine, paint thinner, or any similar materials.

& Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a commercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of genuine leather.

& Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap

Black plate (335,1)

Appearance care 10-5

or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials may be used when necessary. NOTE Strong cleaning agents such as sol- vents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.

& Climate control panel, audio

panel, instrument panel, console panel, switches, combination meter, and other plastic surface

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. NOTE Do not use organic solvents such as paint thinners or gasoline, or strong cleaning agents that contain those solvents.

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

10

10-6 Appearance care

& Navigation monitor (if

equipped)

To clean the navigation monitor, wipe it with a silicone cloth or with a soft cloth. If the navigation monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent. NOTE . Do not spray neutral detergent di- rectly onto the monitor. Doing so could damage the monitor’s components. . Do not wipe the monitor with a hard cloth. Doing so could scratch the monitor. . Do not use cleaning fluid that con- tains thinner, gasoline, or any other volatile substance. Such cleaning fluid could erase the lettering on the switches at the bottom of the monitor.

Black plate (336,1)

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Maintenance schedule ....................................... 11-3
Maintenance precautions................................... 11-3

Before checking or servicing in the engine

11-4

compartment.................................................... When you do checking or servicing in the engine compartment while the engine is running..........

11-4
Engine hood ....................................................... 11-4
Engine compartment overview.......................... 11-6
Engine oil............................................................ 11-7
11-7
11-8
11-9

Checking the oil level ......................................... Changing the oil and oil filter.............................. Recommended grade and viscosity .................... Recommended grade and viscosity under

Recommended spark plugs ..............................

Replacing the air cleaner element .....................

severe driving conditions ............................... Cooling system ................................................ Hose and connections...................................... Engine coolant .................................................

11-10
11-11
11-11
11-11
Air cleaner element .......................................... 11-14
11-14
Spark plugs ...................................................... 11-15
11-15
Drive belts ........................................................ 11-15
Automatic transmission fluid .......................... 11-16
11-16
11-17
Front differential gear oil ................................. 11-17
11-17
11-18
Rear differential gear oil .................................. 11-18
11-18

Checking the oil level ....................................... Recommended grade and viscosity ..................

Checking the fluid level .................................... Recommended fluid .........................................

Checking the gear oil level ...............................

Black plate (21,1)

Maintenance and service

Recommended grade and viscosity .................. Power steering fluid ........................................ Checking the fluid level.................................... Recommended fluid ......................................... Brake fluid........................................................ Checking the fluid level.................................... Recommended brake fluid ............................... Brake booster .................................................. Brake pedal ...................................................... Checking the brake pedal free play .................. Checking the brake pedal reserve distance....... Replacement of brake pad and lining ............ Breaking-in of new brake pads and linings ....... Parking brake stroke ....................................... Tires and wheels.............................................. Types of tires................................................... Tire pressure monitoring system (TPMS) .......... Tire inspection................................................. Tire pressures and wear .................................. Wheel balance ................................................. Wear indicators ............................................... Tire rotation direction mark .............................. Tire rotation..................................................... Tire replacement.............................................. Wheel replacement .......................................... Aluminum wheels ............................................ Chrome plated wheels (if equipped) .............. Windshield washer fluid.................................. Replacement of wiper blades ......................... Windshield wiper blade assembly.....................

11-19
11-19
11-19
11-20
11-20
11-20
11-21
11-21
11-22
11-22
11-22
11-22
11-23
11-23
11-24
11-24
11-24
11-25
11-26
11-28
11-28
11-28
11-29
11-29
11-30
11-30
11-31
11-32
11-33
11-34

11

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Maintenance and service

Windshield wiper blade rubber ......................... Rear window wiper blade assembly .................. Rear window wiper blade rubber.......................

11-34
11-35
11-35
Battery............................................................... 11-37
Fuses ................................................................ 11-38
Main fuse .......................................................... 11-39
Installation of accessories............................... 11-40
Replacing bulbs ............................................... 11-40
11-40
11-40
11-42

Headlights (models with HID headlights) ........... Headlights (models without HID headlights) ...... Parking light (right-hand side)...........................

Black plate (22,1)

Front turn signal light (right-hand side) ............ Front fog light.................................................. Rear combination lights ................................... Back-up light/Tail light ..................................... Rear gate light ................................................. License plate light ........................................... Dome light....................................................... Map light ......................................................... Vanity mirror light ............................................ Door step light................................................. Cargo area light...............................................

11-43
11-43
11-43
11-44
11-45
11-45
11-46
11-47
11-47
11-47
11-48

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Maintenance schedule

Maintenance precautions

The scheduled maintenance items re- quired to be serviced at regular intervals are shown in the “Warranty and Main- tenance Booklet”.

For details of your maintenance schedule, read the separate “Warranty and Main- tenance Booklet”.

When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer.

If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.

Incorrect or incomplete service could cause improper or unsafe vehicle opera- tion. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage.

WARNING

. Testing of an All-Wheel Drive model must NEVER be per- formed on a single two-wheel dynamometer or similar appara- tus. Attempting to do so will result in transmission damage and in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby.

. Always select a safe area when performing maintenance on your vehicle.

Black plate (339,1)

Maintenance and service 11-3

. Always be very careful to avoid injury when working on the vehi- cle. Remember that some of the materials in the vehicle may be hazardous if improperly used or handled, for example, battery acid.

. Your vehicle should only be ser- viced by persons fully competent to do so. Serious personal injury may result to persons not experi- enced in servicing vehicles.

. Always use the proper tools and make certain that they are well maintained.

. Never get under the vehicle sup- ported only by a jack. Always use a safety stands to support the vehicle.

. Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas.

. Do not smoke or allow open flames around the fuel or battery. This will cause a fire.

. Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer.

. Wear adequate eye protection to

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11

fluid on hot engine components. This may cause a fire.

. Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped.

& When you do checking or

servicing in the engine com- partment while the engine is running

WARNING

A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.

11-4 Maintenance and service

in your eyes,

guard against getting oil or fluids in your eyes. If something does get thoroughly wash them out with clean water. . Do not tamper with the wiring of the SRS airbag system or seat- belt pretensioner system, or at- tempt to take its connectors apart, as that may activate the system or it can render it inop- erative. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt preten- sioner needs service, consult your nearest SUBARU dealer.

& Before checking or servicing

in the engine compartment

WARNING

. Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.

. Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine is stopped.

. Do not spill engine oil, engine coolant, brake fluid or any other

Black plate (340,1)

Engine hood

To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original positions. 2. Pull the hood release knob under the instrument panel.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

WARNING

Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily in- jury.

CAUTION

When closing the hood, be careful not to pinch your or other person’s hands or anything else in the hood.

3. Release the secondary hood release located under the front grille by moving the lever toward the left. 4. Lift up the hood.

To close the hood: 1. Lower the hood to a point approxi- mately 20 in (50 cm) from the closed position and then give the hood a strong push down to make it drop. 2. After closing the hood, be sure the hood is securely locked.

If this does not close the hood, release it from a slightly higher position. Do not push the hood forcibly to close it. It could deform the metal.

Black plate (341,1)

Maintenance and service 11-5

11

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-6 Maintenance and service

Engine compartment overview

Black plate (342,1)

1) Air cleaner element (page 11-14) 2) Power steering fluid reservoir

(page 11-19)

3) Differential gear oil level gauge

(page 11-17)

4) Automatic transmission fluid level gauge

(page 11-16)

Fuse box (page 11-38)

5) Brake fluid reservoir (page 11-20) 6) 7) Battery (page 11-37) 8) Windshield washer tank (page 11-32) 9) Radiator cap (page 11-11) 10) Engine oil filler cap (page 11-7) 11) Engine coolant reservoir (page 11-11) 12) Engine oil level gauge (page 11-7)

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Black plate (343,1)

Maintenance and service 11-7

& Checking the oil level Check the engine oil stop. 1. Park the vehicle on a level surface and stop the engine.

level at each fuel

2. Pull out the level gauge, wipe it clean, and insert it again. 3. Be sure the level gauge is correctly it stops with the graphic inserted until ” on its top appearing as symbol shown in the illustration.

“

1) 2)

Full level Low level

4. Pull out the level gauge again and check the oil level on it. If it is below the low level, add oil to bring the level up to the full level.

CAUTION

. Use only engine oil with the recommended grade and vis- cosity.

11

Engine oil

NOTE . The engine oil consumption rate is not stabilized, and therefore cannot be determined until the vehicle has tra- veled at least several thousand miles (kilometers). Even after break-in, when the vehicle is used under severe driv- ing conditions such as those men- tioned in the “Warranty and Mainte- nance Booklet”, engine oil is con- sumed or deteriorated more quickly than under normal driving conditions. If you drive your vehicle under these severe conditions, you should check the oil level at least at every second fuel fill-up time, and change the oil more frequently. Please refer to the “Warranty and Maintenance Booklet” for more details. . If the oil consumption rate seems abnormally high after the break-in period, for example more than 1 quart per 1,200 miles or 1 liter per 2,000
kilometers, we recommend that you contact your SUBARU dealer.

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Black plate (344,1)

11-8 Maintenance and service

. Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust pipe, be sure to wipe it off.

If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. To prevent overfilling the engine oil, do not add any additional oil above the full level when the engine is cold. & Changing the oil and oil filter Change the oil and oil filter according to the maintenance schedule in the “War- ranty and Maintenance Booklet”. filter must be The engine oil and oil changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold whether. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.

4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of properly.

6. Open the access cover by removing the five clips and turning the access cover counterclockwise. The oil filter will be exposed.

WARNING

Be careful not to burn yourself with hot engine oil.

5. Wipe the seating surface of the drain plug with a clean cloth and tighten it securely with a new sealing washer after the oil has completely drained out.

7. Remove the oil filter with an oil filter wrench.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

8. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. filter by the amount 9. Tighten the oil indicated in the following table after the seal makes contact with the bottom of engine.

Oil filter color Part number Amount of ro-

tation

Black

15208AA031

3/4 rotation

CAUTION

. Never over tighten the oil filter because that can result in an oil leak.

. Thoroughly wipe off any engine oil that has spilled over the exhaust pipe and/or under-cover. If left unremoved, the oil could catch fire.

10. Reinstall the cover under the oil filter. 11. Pour engine oil through the filler neck.

Oil capacity (guideline):

6.7 US qt (6.3 liters, 5.5 Imp qt)

The oil quantity indicated above is only a guideline. The necessary quantity of oil depends on the quantity of oil that has been drained. The quantity of drained oil differs slightly depending on the tempera- ture of the oil and the time the oil is left flowing out. After refilling the engine with oil, therefore, you must use the level gauge to confirm that the level is correct. 12. Start the engine and make sure that no oil leaks appear around the filter’s rubber seal and drain plug. 13. Run the engine until it reaches the normal operating temperature. Then stop the engine and wait a few minutes to allow the oil drain back. Check the oil level again and if necessary, add more engine oil.

& Recommended grade and

viscosity

CAUTION

Use only engine oil with the recom- mended grade and viscosity.

Black plate (345,1)

Maintenance and service 11-9

Oil grade:

ILSAC GF-4, which can be identified with the ILSAC certification mark (Starburst mark) or API classification SM with the words “ENERGY CONSERVING”

These recommended oil grades can be identified by looking for either or both of the following marks displayed on the oil container.

ILSAC Certification Mark (Starburst Mark)

11

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-10 Maintenance and service

API Service label 1)

Indicates the oil quality by API designa- tions Indicates the SAE oil viscosity grade Indicates that capabilities

the oil has fuel saving

2) 3)

In choosing an oil, you want the proper quality and viscosity, as well as one that will add to fuel economy. The following table lists the recommended viscosities and applicable temperatures. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU.

Black plate (346,1)

& Recommended grade and

viscosity under severe driv- ing conditions

If the vehicle is used in desert areas, in areas with very high temperatures, or used for heavy-duty applications such as towing a trailer, use of oil with the following grade and viscosities is recommended.

API classification SM (or SL):

SAE viscosity No.:

30, 40, 10W-50, 20W-40, 20W-50

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

SAE viscosity number and applicable temperature *:

5W-30 is recommended.

Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better in hot weather, oil of higher viscosity is required to properly lubricate the engine.

fuel economy. However,

Cooling system

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

CAUTION

. Vehicles are filled at the factory with SUBARU Super Coolant that does not require the first change for 11 years/137,500 miles (11
years/220,000 km). This coolant should not be mixed with any other brand or type of coolant during this period. Mixing with a different coolant will reduce the life of the coolant. Should it be necessary to top off the coolant f o r a n y r e a s o n , u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is

shortened to that of the mixing coolant.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

& Hose and connections Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific temperature. If the radiator cooling fan does not operate even when the engine coolant tempera- ture gauge exceeds the normal operating range, the cooling fan circuit may be defective. Check the fuse and replace it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU dealer.

If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness.

Black plate (347,1)

Maintenance and service 11-11

& Engine coolant ! Checking the coolant level

Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, remove the radiator cap and refill as required.

11

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-12 Maintenance and service

3. After refilling the reserve tank and the radiator, reinstall the caps and check that the rubber gaskets inside the radiator cap are in the proper position.

CAUTION

. Be careful not

to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.

Black plate (348,1)

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

3. Loosen the radiator cap to drain the coolant from the radiator. Then drain the coolant from the reserve tank. Tighten the drain plug securely.

! Changing the coolant Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi- tioner using the following procedures according to the maintenance schedule in the “Warranty and Maintenance Book- let”. 1. Remove the under cover.

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

4.

Install the under cover.

2. Place a proper container under the drain plug and loosen the drain plug.

5. Slowly pour the coolant and fill up to

1)

Fill up to here

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

just below the filler neck, allowing enough room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the system.

Coolant capacity (guideline):

8.0 US qt (7.6 liters, 6.7 Imp qt)

CAUTION

1)

“FULL” level mark

6. Pour the coolant and fill to the reser- voir tank’s “FULL” level mark.

. Be careful not

to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

7. Put the radiator cap back on and tighten firmly. At this time, make sure that the rubber gasket in the radiator cap is

Black plate (349,1)

Maintenance and service 11-13

correctly in place. 8. Start and race the engine at 2,000 to 3,000 rpm for 5 to 6 times within 40
seconds. 9. Stop the engine and wait until the coolant cools down (122 to 1408F [50 to 608C]). If there is any loss of coolant, add coolant to the radiator’s filler neck and to the reserve tank’s “FULL” level. 10. Put the radiator cap and reservoir cap back on and tighten firmly.

11

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-14 Maintenance and service

Air cleaner element

WARNING

Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. the air cleaner element installed when the engine backfires, you could be burned.

is not

If

CAUTION

When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.

The air cleaner element functions as a filter screen. When the element is perfo- rated or removed, engine wear will be excessive and engine life shortened.

is unnecessary to clean or wash the

It element.

Black plate (350,1)

cleaner case cover.

& Replacing the air cleaner

element

Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts.

4. Open the air cleaner case cover and remove the air cleaner element. 5. Clean the inside of the air cleaner case and case cover with a damp cloth and install a new air cleaner element.

1) Connector 2) Clamp 3) Air intake boot 4) Clip

1. Unplug the connector that is attached to the top of the air cleaner case. 2. Loosen the screw on the clamp and pull the air cleaner case. 3. Unsnap the two clips holding the air

intake boot out of

the air

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

6. To install the air cleaner case cover, insert the three projections on the air cleaner case cover into the slits on the air cleaner case. 7.

Install in the reverse order of removal.

Black plate (351,1)

Maintenance and service 11-15

Spark plugs

Drive belts

It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer.

The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.

& Recommended spark plugs

SILFR6C11 (NGK)

The alternator, power steering pump, and air conditioner compressor depend on drive belts. Satisfactory performance re- quires that belt tension be correct. It tension is unnecessary to check belt periodically because your engine is equipped with an automatic belt tension adjuster. However, replacement of the belt should be done according to the main- tenance schedule in the “Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If a belt is loose, cracked, or worn, contact your SUBARU dealer.

11

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-16 Maintenance and service

Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the level gauge.

Though the fluid level can be checked without warming up the fluid on the “COLD” range, we recommend checking the fluid level when the fluid is at operating temperature. ! Checking the fluid level when the

fluid is hot

Check the fluid level monthly. 1. Drive the vehicle several miles to raise the temperature of the transmission fluid up to normal operating temperature; 158
to 1768F (70 to 808C) is normal. 2. Park the vehicle on a level surface and set the parking brake. 3. First shift in each position. Then shift it in the “P” position, and run the engine at idling speed.

the select

lever

Black plate (352,1)

4. Pull out the level gauge and check the fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended automatic transmission fluid up to the upper level.

! Checking the fluid level when the

fluid is cold

When the fluid level has to be checked without time to warm up the automatic transmission, check to see that the fluid level is between the lower level and upper level on the “COLD” range. If it is below that range, add fluid up to the upper level. Be careful not to overfill.

CAUTION

Be careful not to spill automatic transmission fluid when adding it. If automatic transmission fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If automatic transmission fluid gets on the exhaust pipe, be sure to wipe it off.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

1) Yellow handle

1) HOT range 2) COLD range 3) Upper level Lower level 4)

Front differential gear oil & Checking the oil level

& Recommended fluid

Use one of the following types of auto- matic transmission fluid.

SUBARU ATF IDEMITSU ATF HP

NOTE Using any non-specified type of auto- matic transmission fluid could result in damage inside the transmission. When replacing the automatic transmission fluid, be sure to use a fluid of the types specified above.

1) Yellow handle

1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again.

Black plate (353,1)

Maintenance and service 11-17

1) Upper level 2) Lower level

3. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.

CAUTION

Be careful not to spill front differ- ential gear oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If oil gets on the exhaust pipe, be sure to wipe it off.

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11

11-18 Maintenance and service

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together.

Oil grade:

API classification GL-5

Rear differential gear oil & Checking the gear oil level Your vehicle may be equipped with a rear differential protector. The differential pro- tector provides protection to the rear differential assembly during off-road use. Removal of the rear differential protector is not required when checking the oil level.

SAE viscosity No. and applicable tempera- ture

1) Filler plug 2) Drain plug

Black plate (354,1)

1) Filler hole 2) Drain hole 3) Oil level

Remove the plug from the filler hole and check the oil level. The oil level should be kept even with the bottom of the filler hole. If the oil level is below the bottom edge of the hole, add oil through the filler hole to raise the level.

CAUTION

. Be careful not to spill rear differ- ential gear oil when adding it. If rear differential gear oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If rear differential gear oil gets on the exhaust pipe, be sure to wipe

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

it off.

. If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together.

Oil grade:

API classification GL-5

SAE viscosity No. and applicable tempera- ture

Black plate (355,1)

Maintenance and service 11-19

Power steering fluid & Checking the fluid level

WARNING

Be careful not because the fluid may be hot.

to burn yourself

CAUTION

11

. When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank. And never use different brands together.

. Avoid spilling fluid when adding

it in the tank.

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11-20 Maintenance and service

. Be careful not

to spill power steering fluid when adding it. If power steering fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If power steering fluid gets on the exhaust pipe, be sure to wipe it off.

The power steering fluid expands greatly as its temperature rises; the fluid level differs according to fluid temperature. Therefore, tank has two different checking ranges for hot and cold fluids.

the reservoir

mended fluid as necessary to bring the level between the “MIN” and “MAX” line. If the fluid level is extreme low, it may indicate possible leakage. Consult your SUBARU dealer for inspection.

& Recommended fluid

Use one of the following types of auto- matic transmission fluid.

SUBARU ATF IDEMITSU ATF HP “Dexron III” Type Automatic Transmis- sion Fluid

Check the power steering fluid level monthly. 1. Park the vehicle on a level surface, and stop the engine. 2. Check the fluid level of the reservoir tank. When the fluid is hot after the vehicle has been run: Check that is between “HOT MIN” and “HOT MAX” on the surface of the reservoir tank. When the fluid is cool before the vehicle is run: Check that the oil is between “COLD MIN” and “COLD MAX” on the surface of the reservoir tank. 3. applicable “MIN”

than the line, add the recom-

the fluid level

is lower

the oil

level

level

If

Black plate (356,1)

Brake fluid & Checking the fluid level

WARNING

to your eyes.

. Never let brake fluid contact your eyes because brake fluid can be harmful If brake fluid gets in your eyes, immedi- ately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable.

. Brake fluid absorbs moisture from the air. Any absorbed moist- ure can cause a dangerous loss of braking performance.

. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

CAUTION

. When adding brake fluid, be care- ful not to allow any dirt into the reservoir.

. Never splash the brake fluid over painted surfaces or rubber parts.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Black plate (357,1)

Maintenance and service 11-21

& Recommended brake fluid

Brake booster

FMVSS No. 116, fresh DOT 3 or DOT 4
brake fluid

CAUTION

Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand.

If the brake booster does not operate as described in the following, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary. 2. With the brake pedal depressed, start the engine. The pedal should move slightly down to the floor. 3. With the brake pedal depressed, stop the engine and keep the pedal depressed for 30 seconds. The pedal height should not change. 4. Start the engine again and run for approximately 1 minute then turn it off. Depress the brake pedal several times to check the brake booster. The brake booster operates properly if the pedal stroke decreases with each depression.

11

Alcohol contained in the brake fluid may damage them.

. Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off.

Check the fluid level monthly.

Check the fluid level on the outside of the reservoir. If the level is below “MIN”, add the recommended brake fluid to “MAX”. Use only brake fluid from a sealed container.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Black plate (358,1)

11-22 Maintenance and service

Brake pedal

Check the brake pedal free play and reserve distance according to the main- tenance schedule in the “Warranty and Maintenance Booklet”.

& Checking the brake pedal

free play

& Checking the brake pedal

reserve distance

Replacement of brake pad and lining

CAUTION

If you continue to drive despite the scraping noise from the audible brake pad wear indicator, it will result in the need for costly brake rotor repair or replacement.

1) More than 2.16 in (55 mm)

Depress the pedal with a force of approxi- mately 66 lbf (294 N, 30 kgf) and measure the distance between the upper surface of the pedal pad and the floor. When the measurement is smaller than the specification, or when the pedal does not operate smoothly, contact with your SUBARU dealer.

1)

0.02 – 0.08 in (0.5 – 2.0 mm)

Stop the engine and firmly depress the brake pedal several times. Lightly pull the brake pedal up with one finger to check the free play with a force of less than 2 lbf (10 N, 1 kgf). the free play is not within proper If specification, contact your SUBARU deal- er.

The front disc brake and the right rear disc brake have audible wear indicators on the brake pads. If the brake pads wear close to their service limit, the wear indicator makes a very audible scraping noise when the brake pedal is applied.

If you hear this scraping noise each time

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

1. Drive the vehicle at a speed of approximately 22 mph (35 km/h). 2. Depress the parking brake pedal SLOWLY and GENTLY. (Pressing with a force of approximately 34 lbf [150 N, 15
kgf].) 3. Drive the vehicle for approximately 220 yards (200 meters) in this condition. 4. Wait 5 to 10 minutes for the parking brake to cool down. Repeat this proce- dure. 5. Check the parking brake stroke. If the parking brake stroke is out of the specified range, adjust it by turning the adjusting nut located on the parking brake pedal.

Parking brake stroke:

5 – 6 notches / 67 lbf (300 N, 30 kgf)

you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible.

& Breaking-in of new brake

pads and linings

When replacing the brake pad or lining, use only genuine SUBARU parts. After replacement, the new parts must be broken in as follows. ! Brake pad and lining While maintaining a speed of 30 to 40
mph (50 to 65 km/h), step on the brake pedal this five or more times. ! Parking brake lining

lightly. Repeat

WARNING

A safe location and situation should be selected for break-in driving.

CAUTION

Pressing the parking brake pedal too forcefully may cause the rear wheels to lock. To avoid this, be certain to press the pedal slowly and gently.

Black plate (359,1)

Maintenance and service 11-23

Parking brake stroke

Check the parking brake stroke according to the maintenance schedule in the “Warranty and Maintenance Booklet”. When the parking brake is properly adjusted, braking power is fully applied by depressing the pedal five to six notches gently but firmly (approximately 67 lbf [300
N, 30 kgf]). the parking brake pedal stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer.

If

11

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

Black plate (360,1)

11-24 Maintenance and service

Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle. ! All season tires The factory-installed tires on your new vehicle are all season tires. All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road conditions. However all season tires do not offer as much traction performance as winter (snow) tires in heavy or loose snow or on icy roads. All season tires are identified by “ALL SEASON” and/or “M+S” (Mud & Snow) on the tire sidewall. ! Summer tires Summer tires are high-speed capability tires best suited for highway driving under dry conditions. Summer tires are inadequate for driving on slippery roads such as on snow- covered or icy roads. If you drive your vehicle on snow-covered or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to

replace all four tires. ! Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads.

& Tire pressure monitoring

system (TPMS)

The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low. The tire pressure monitor- ing system will activate only when the vehicle is driven. Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused by running over a sharp object).

If you adjust the tire pressures in a warm garage and will then drive the vehicle in cold outside air, the resulting drop in tire pressures may cause the low tire pressure warning light to illuminate. To avoid this problem when adjusting the tire pressures in a warm garage, inflate the tires to pressures higher than those shown on the tire placard. Specifically, inflate them by an extra 1 psi (6.9 kPa, 0.07 kgf/cm2) for every difference of 108F (5.68C) between

the temperature in the garage and the temperature outside. By way of example, the following table shows the required tire pressures that correspond to various out- side temperatures when the temperature in the garage is 608F (15.68C). Standard tire pressures: Front: 33 psi (230 kPa, 2.3 kgf/cm2) Rear: 32 psi (220 kPa, 2.2 kgf/cm2) Garage temperature: 608F (15.68C)

Outside

temperature

Adjusted pressure [psi (kPa, kgf/cm2)] Front Rear

308F (−18C)

36 (250, 2.5)

35 (240, 2.4)

108F (−128C)

38

(265, 2.65)

37

(255, 2.55)

−108F (−238C)

40 (280, 2.8)

39 (270, 2.7)

If the low tire pressure warning light illuminates when you drive the vehicle in cold outside air after adjusting the tire pressures in a warm garage, re-adjust the tire pressures using the method described above. Then, increase the vehicle speed to at least 20 mph (32 km/h) and check to see that the low tire pressure warning light turns off a few minutes later. If the low tire pressure warning light does not turn off, the tire pressure monitoring system may

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible.

While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up. After illumination of the low tire pressure warning light, any increase in the tire pressures caused by an increase in the outside air temperature or by an increase in the temperature in the tires can cause the low tire pressure warning light to turn off.

System resetting is necessary when the wheels are changed (for example, a switch to snow tires) and new TPMS valves are installed on the newly fitted wheels. Have this work performed by a SUBARU dealer following wheel replace- ment.

It may not be possible to install TPMS valves on certain wheels that are on the market. Therefore, if you change the wheels (for example, a switch to snow tires), use wheels that have the same part number as the standard-equipment wheels. Without four operational TPMS valve/sensors on the wheels, the TPMS will not fully function and the warning light in the instrument panel will illuminate steadily after blinking for approximately one minute.

When a tire is replaced, adjustments are necessary to ensure continued normal operation of the tire pressure monitoring system. As with wheel replacement, there- fore, you should have the work performed by a SUBARU dealer.

WARNING

If the low tire pressure warning light does not illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blink- ing for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possi- ble. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. If illuminates while driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire

this light still

Black plate (361,1)

Maintenance and service 11-25

as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. the light illuminates steadily after blinking for approximately one minute, promptly contact a SUBARU dealer to have the system inspected.

If

& Tire inspection Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Contact your SUBARU dealer ately if you find any problem. NOTE . When the wheels and tires strike curbs or are subjected to harsh treat- ment as when the vehicle is driven on a rough surface, they can suffer damage – CONTINUED –

immedi-

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11

11-26 Maintenance and service

that cannot be seen with the naked eye. This type of damage does not become evident until time has passed. Try not to drive over curbs, potholes or on other rough surfaces. If doing so is unavoidable, keep the vehicle’s speed down to a walking pace or less, and approach the curbs as squarely as possible. Also, make sure the tires are not pressed against the curb when you park the vehicle. . If you feel unusual vibration while driving or find it difficult to steer the vehicle in a straight line, one of the tires and/or wheels may be damaged. Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected.

& Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’ service lives and is essential for good running perfor- mance. Check and, if necessary, adjust the pressure of each tire (including the spare) at least once a month (for example, during a fuel stop) and before any long journey.

Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the values shown on the tire placard. The tire placard is located on the door pillar on the driver’s side.

Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the outside temperature. It is best to check tire pressure outdoors before driving the vehicle.

When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure.

Black plate (362,1)

NOTE . The air pressure in a tire increases by approximately 4.3 psi (30 kPa, 0.3
kgf/cm2) when the tire becomes warm. . The tires are considered cold when the vehicle has been parked for at least 3 hours or has been driven less than 1
mile (1.6 km).

WARNING

Do not let air out of warm tires to adjust pressure. Doing so will result in low tire pressure.

Incorrect tire pressures detract from con- trollability and ride comfort, and they cause the tires to wear abnormally.

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

. Correct evenly)

tire pressure (tread worn

. Abnormally low tire pressure (tread worn at shoulders)

. Abnormally high tire pressure (tread worn in center)

Black plate (363,1)

Maintenance and service 11-27

Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower.

Rolling resistance is high, so fuel con- sumption is also higher.

is poor. Also,

the tire Ride comfort magnifies the effects of road-surface bumps and dips, possibly resulting in vehicle damage.

WARNING

Driving at high speeds with exces- sively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp in- crease in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident.

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11

11-28 Maintenance and service

that

& Wheel balance Each wheel was correctly balanced when your vehicle was new, but the wheels will become unbalanced as the tires become worn during use. Wheel imbalance causes the steering wheel to vibrate slightly at certain vehicle speeds and detracts from the vehicle’s straight-line stability. It can also cause steering and suspension sys- tem problems and abnormal tire wear. If you suspect the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE Loss of correct wheel alignment* causes the tires to wear on one side and reduces the vehicle’s running stability. Contact your SUBARU dealer if you notice abnormal tire wear. *: The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering perfor- mance.

& Wear indicators

Black plate (364,1)

cause the vehicle to hydroplane. The resulting loss of vehicle control can lead to an accident.

NOTE For safety, inspect the tire tread reg- ularly and replace the tires before their tread wear indicators become visible.

& Tire rotation direction mark

1) New tread 2) Worn tread 3)

Tread wear indicator

Each tire incorporates a tread wear indicator, which becomes visible when the depth of the tread grooves decreases to 0.071 in (1.8 mm). A tire must be replaced when the tread wear indicator appears as a solid band across the tread.

WARNING

When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately. With a tire in this condition, driving at high speeds in wet weather can

Example of tire rotation direction mark 1)

Front

the tire has the rotation direction the tire rotation direction

If specification, mark is placed on its sidewall. When you install a tire that has the tire rotation direction mark, install the tire with

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

the direction mark facing forward.

& Tire rotation

Vehicles equipped with 4 non-unidirec- tional tires 1)

Front

Vehicles equipped with unidirectional tires 1)

Front

Tire wear varies from wheel to wheel. To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,000
km). Move the tires to the positions shown in the illustration each time they are rotated. Replace any damaged or unevenly worn tire at tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tightened.

rotation. After

the time of

After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose.

Black plate (365,1)

Maintenance and service 11-29

& Tire replacement The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbitrarily. The tires fitted as standard equipment are optimally matched to the characteristics of the vehicle and were selected to give the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a size and construction matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard.

Using tires of a non-specified size detracts from controllability, ride comfort, braking performance, speedometer accuracy and odometer accuracy. It also creates incor- rect body-to-tire clearances and inappro- priately changes the vehicle’s ground clearance.

All four tires must be the same in terms of manufacturer, brand (tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment.

For safe vehicle operation, SUBARU recommends replacing all tires at the same time.

four

– CONTINUED –

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

11

11-30 Maintenance and service

WARNING

WARNING

Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper opera- tion and may cause the tires to rub against the wheel well housing dur- ing turns. The resulting loss of vehicle control could lead to an accident.

. All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, de- gree of wear, speed symbol, load index and size. Mixing tires of different types, sizes or degrees of wear can result in damage to the vehicle’s powertrain. Use of different types or sizes of tires can also dangerously reduce controllability and braking per- formance and can lead to an accident.

. Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously re- duce controllability, resulting in an accident.

& Wheel replacement When replacing wheels due, for example, to damage, make sure the replacement wheels match the specifications of the wheels that are fitted as standard equip- ment. Replacement wheels are available from SUBARU dealers.

Black plate (366,1)

Aluminum wheels . Aluminum wheels can be scratched and damaged easily. Handle them care- fully to maintain their appearance, perfor- mance, and safety.

1)

The length of the wheel nut wrench

CAUTION

There are 2 types of wheel nut wrenches that apply to different lengths. For an aluminum wheel vehicle, the 11.2-inch (285 mm) wheel nut wrench is equipped as a mainte- nance tool. And for a chrome plated wheel vehicle, the 13.2-inch (335
mm) wheel nut wrench is equipped

北米Model "A3150BE-A" EDITED: 2009/ 6/ 23

as well. Always use a wheel nut wrench for an aluminum wheel. If you use a wrench for a chrome plated wheel, you cannot tighten it to the specified torque.

. When any of the wheels are removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nuts after driving approximately 600 miles (1,000 km). If any nut is loose, tighten it to the following specified torque. A tightening sequence specification for the wheel nuts can be found in “Flat tires” F9- 6. Wheel nuts tightening torque for alu- minum wheel: 74 to 89 lbf·ft (100 to 120 N·m, 10 to 12
kgf·m) This torque is equivalent to applying approximately 88 to 110 lbs (40 to 50 kg) at the top of the wheel nut wrench. . Never apply oil to the threaded parts, wheel nuts, or the wheel. . Never let the wheel rub against sharp protrusions or curbs. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels.

tapered surface of

Chrome plated wheels (if equipped)

1)

The length of the wheel nut wrench

CAUTION

There are 2 types of wheel nut wrenches that apply to different