Login- Download PDF Manual
-
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.
1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Push the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place.
To sound the horn, push the horn pad.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (7,1)
Climate control
Air conditioner button ........................................ Temperature sensors .........................................
4-10
4-11Operating tips for heater and air
conditioner ...................................................... Cleaning ventilation grille................................... Efficient cooling after parking in direct
sunlight ...........................................................
Lubrication oil circulation in the refrigerant
circuit.............................................................. Checking air conditioning system before summer season ............................................................ Cooling and dehumidifying in high humidity and low temperature weather conditions ................. Air conditioner compressor shut-off when engine is heavily loaded.............................................. Refrigerant for your climate control system ........ Air filtration system (if equipped)..................... Replacing an air filter.........................................
4-11
4-114-11
4-12
4-12
4-12
4-12
4-12
4-12
4-13Ventilator.............................................................. Air flow selection ................................................ Center and side ventilators..................................
Manual climate control system
(if equipped) ..................................................... Control panel ...................................................... Heater operation ................................................. Air conditioner operation.....................................
Automatic climate control system
(if equipped) ..................................................... Control panel ...................................................... To use as full-automatic climate control
system..............................................................
4-2
4-2
4-34-3
4-3
4-5
4-74-8
4-84-8
To use as semi-automatic climate control
system.............................................................. 4-8
Fan speed control dial......................................... 4-9
Temperature control dial...................................... 4-9
Air flow control dial............................................. 4-9
Air inlet selection button .................................... 4-10北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (150,1)
4-2 Climate control
Ventilator & Air flow selection
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Center and side ventilators ! Center ventilators
! Side ventilators
Move the tab up and down or right and left to adjust the flow direction.
1) Open 2) Close 3)
Thumbwheel
Move the tab up and down or right and left to adjust the flow direction. To open or close the ventilator, turn the thumbwheel up or down.
Black plate (151,1)
Climate control 4-3
Manual climate control sys- tem (if equipped) & Control panel
Temperature control dial Fan speed control dial
1) 2) 3) Air flow control dial 4) Rear window defogger button (Refer to
the “Rear window defogger button” in chapter 3.)
5) Air conditioner button 6) Air inlet selection button ! Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red side (warm).
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
4-4 Climate control
! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. ! Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel
outlets.
: Air flows through the instrument panel
outlets and the foot outlets.
: Air flows through the foot outlets and some through the windshield defroster outlets.
mode. In this state, you cannot select “recir- culation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air condi- tioner compressor by pressing the air conditioner button. ! Air conditioner button
: Air
flows through the windshield
defroster outlets and foot outlets.
: Air
flows through the windshield
defroster outlets. NOTE When the dial is placed in the “ ” or “ ” position, the air conditioner com- pressor operates automatically regard- less of the position of the air condi- tioner button to defog the windshield quickly. However the indicator on the air conditioner button will not come on. At the same time, the air inlet selection to “outside air” is automatically set
The air conditioner operates only when the engine is running.
Push the air conditioner button while the fan is in operation to turn on the air conditioner. The indicator light will come on.
Push it again to turn off the air conditioner.
Black plate (152,1)
! Air inlet selection button
ON position (Recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON posi- tion. The indicator light will come on. Place the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road.
OFF position (Outside air): Outside air is drawn into the passenger compartment. Push the air inlet selection button again to the OFF position. The indicator light will go off. Place the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
WARNING
Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
& Heater operation ! Defrosting or defogging the wind-
shield
the way to the right. 3. Set the fan speed control dial to the highest speed.
” or “
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates regardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding thumbwheel down.
To direct warm air to the windshield and front door windows: 1. Set the air flow control dial to the “ position. 2. Turn the temperature control dial all
”
Black plate (153,1)
Climate control 4-5
! Heating and defrosting
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to the “ position. 2. Set the temperature control dial to the most comfortable level. 3. Set the fan speed control dial to the desired speed.
”
” or “
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates regardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time.
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (154,1)
4-6 Climate control
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding thumbwheel down. ! Heating
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding thumbwheel down. ! Bi-level heating
desired speed.
Setting the temperature control dial fully turned to the red area or blue area decreases the temperature difference between the air from the instrument panel outlets and the air from the foot outlets. ! Ventilation
To direct warm air toward the floor: 1. Set the air inlet selection button to the OFF position. 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial to the most comfortable level. 4. Set the fan speed control dial to the desired speed.
”
This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the OFF position. 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the
”
To force outside air through the instrument panel outlets: 1. Set the air inlet selection button to the OFF position. 2. Set the air flow control dial to the “ position. 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed.
”
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (155,1)
Climate control 4-7
red side. 3. Set the fan speed control dial at the highest speed.
in the “
The air conditioner compressor automati- cally operates when the air flow control ” position to dial set provide better defogging performance. However, the air conditioner indicator light does not come on at this time.
” or “
When driving on a dusty road, set the air inlet selection button to the “ON” position.
WARNING
Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
& Air conditioner operation ! Cooling or dehumidifying
through the instrument panel outlets: 1. Set the air inlet selection button to the OFF position. 2. Set the air flow control dial to the “ position. 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue side. 5. Set the fan speed control dial at the highest speed.
”
! Defrosting or defogging
1) ON position
For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow
To direct warm air to the windshield and front door windows: 1. Set the air flow control dial to the “ position. 2. Set the temperature control dial to the
”
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
4-8 Climate control
Automatic climate control system (if equipped)
Although this climate control system can be used as a full-automatic climate control system, it can also, if desired, be used as a semi-automatic climate control system. When it is used as a full-automatic climate control system, the outlet air temperature, fan speed, air flow distribution, air inlet control, and air conditioner compressor operation are all automatically controlled to maintain a constant, comfortable tem- perature inside the vehicle. NOTE . Operate the automatic climate con- trol system when the engine is running. . When the engine coolant is cold, the blower does not run. . In the “AUTO” mode, when the air temperature in the passenger compart- ment is sufficiently cool, the air condi- tioner compressor does not operate. For efficient defogging or dehumidify- ing in cold weather, press the “A/C” button to operate the air conditioner compressor. . Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres-
sor automatically and the “A/C” indi- cator light on the control panel comes on.
& Control panel
Temperature control dial Fan speed control dial
1) 2) 3) Air flow control dial 4) Rear window defogger button (Refer to
the “Rear window defogger button” in chapter 3.)
5) Air inlet selection button 6) Air conditioner button
& To use as full-automatic cli-
mate control system
Place the temperature control dial in the position for your desired temperature, then
Black plate (156,1)
set the other dials and buttons as de- scribed in the following. The system’s functions will then switch to AUTO mode and be controlled automatically. . Air flow control dial: AUTO position . Fan speed control dial: AUTO position . Air inlet selection button: Press for at least 1 second. (Indicator will flash twice.) . Air conditioner button: Press for at least 1 second. (Indicator will flash twice.)
& To use as semi-automatic
climate control system
Each function can be individually set to AUTO mode independently of the others. Any function set to AUTO mode is con- trolled automatically. Any function not set to AUTO mode can be manually adjusted as desired. The temperature can be set within a range of 65 to 858F (20 to 308C).
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Fan speed control dial
NOTE With the fan speed control dial in the AUTO position and the air flow control dial in the “ ”, or “ ” position, the fan does not operate during engine warm-up until the engine coolant tem- perature exceeds approx. 1228F (508C).
”, “
& Temperature control dial
The fan operates only with the ignition switch in the “ON” position. The fan speed control dial is used to select the AUTO (automatic control) mode or to select the desired fan speed. The dial’s positions and their functions are as follows: OFF: The fan does not operate. AUTO: The fan speed is adjusted auto- matically in accordance with the air temperature inside and outside the pas- senger compartment, the intensity of sun- light, and other factors. SUBARU recom- mends using the AUTO position. Other positions: The fan speed can be adjusted in seven steps.
This dial is used to set the desired interior temperature. With the dial set to your desired temperature, the system automa- tically adjusts the temperature of air supplied from the outlets such that the desired temperature is achieved and maintained. If the dial is turned fully counterclockwise, the system gives maximum cooling per-
Black plate (157,1)
Climate control 4-9
formance. If the dial is turned fully clock- wise, the system gives maximum heating performance.
& Air flow control dial
This dial has the following six positions. The outlets from which air is supplied in each position are as follows: AUTO: The air flow control is adjusted automatically in accordance with the air temperature inside and outside the pas- senger compartment, the intensity of sun- light, and other factors. SUBARU recom- mends using the AUTO position.
: Instrument panel outlets
Instrument panel outlets and foot
outlets
: Foot outlets and windshield defroster – CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
4-10 Climate control
outlets (relatively little air from windshield defroster outlets)
: Windshield defroster outlets and foot
outlets
: Windshield defroster outlets
NOTE When the dial is placed in the “ ” or “ ” position, the air conditioner com- pressor operates automatically to de- fog the windshield quickly. At the same time, the air inlet selection is automa- tically set to “outside air” mode.
& Air inlet selection button
ON position (Recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON position
for fast cooling with the air conditioner or when driving on a dusty road. The indicator light will come on. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will go off. AUTO: When the air inlet selection button is pressed for at the indicator flashes twice. The air inlet control is then adjusted automatically in accor- dance with the air temperature inside and outside the passenger compartment, the intensity of sunlight, and other factors. Pressing the air inlet selection button cancels the AUTO mode. SUBARU re- commends using the AUTO position.
least 1 second,
WARNING
Continued operation in the ON posi- tion may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
Black plate (158,1)
& Air conditioner button
The button’s positions and their functions are as follows: ON: The air conditioner operates while the fan is running. Push the button to select this position. The indicator light will come on. OFF: The air conditioner does not oper- ate. Push the button again to select position. The indicator light will go off. AUTO: When the button is pressed for at least 1 second, the indicator flashes twice. The air conditioner compressor operation is then adjusted automatically in accor- dance with the air temperature inside and outside the passenger compartment, the intensity of sunlight, and other factors.
this
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Pressing the button cancels the AUTO mode. SUBARU recommends using the AUTO position. NOTE The air conditioner’s compressor does not operate with an outside tempera- ture of 328F (08C) or lower.
& Temperature sensors
the sensors, observe the following pre- cautions: – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors.
The sensors are located as follows: – Solar sensor: beside the windshield defroster grille. – Interior air temperature sensor: near the ignition switch. – Outside temperature sensor: behind the front grille.
Interior air temperature sensor
1) 2) Solar sensor
The automatic climate control system employs several sensors. These sensors are delicate. treated properly and become damaged, the sys- tem may not be able to control the interior temperature correctly. To avoid damaging
they are not
If
Black plate (159,1)
Climate control 4-11
Operating tips for heater and air conditioner & Cleaning ventilation grille
Always keep the front ventilation inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser.
& Efficient cooling after parking
in direct sunlight
After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Air conditioner compressor
shut-off when engine is heavily loaded
To improve acceleration and gas mileage, the air conditioner compressor is designed to temporarily shut off during air condi- tioner operation whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.
& Refrigerant for your climate
control system
Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
4-12 Climate control
heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cooling efficiency.
& Lubrication oil circulation in
the refrigerant circuit
Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil.
& Checking air conditioning
system before summer sea- son
Check the air conditioner unit for refriger- ant leaks, hose conditions, and proper operation each spring. Have your SUBARU dealer perform this check.
& Cooling and dehumidifying in
high humidity and low tem- perature weather conditions Under certain weather conditions (high relative humidity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
Black plate (160,1)
Air filtration system (if equipped)
If your vehicle’s air conditioning system is equipped with an air filtration system, replace the filter element according to the replacement schedule shown in the following. This schedule should be fol- lowed to maintain the filter’s dust collec- tion ability. Under extremely dusty condi- tions, the filter should be replaced more frequently. is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit.
It
Replacement schedule:
Every 12 months or 7,500 miles (12,000
km) whichever comes firstCAUTION
Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter: – Reduction of the air flow through
the vents.
– Windshield gets easily fogged or
misted.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained.
& Replacing an air filter
Black plate (161,1)
Climate control 4-13
one.
CAUTION
The arrow mark on the filter must point UP.
1) Air filter cover
2. Remove the air filter cover.
1. Remove the glove box. (1) Open the glove box. (2) Remove the nine screws securing the glove box.
1) Air filter cover
4. Reinstall the air filter cover.
1) Air filter element 2) Arrow mark
3. Replace the air filter element with new
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
4-14 Climate control
5. Reinstall the glove box. 6. Close the glove box.
1) Service label 2) Caution label
7. LABEL installation
the information on the
(1) Fill out service label (small). (2) Attach the service label to the driver side door pillar and the caution label the instrument panel.
to the driver side end of
Black plate (162,1)
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (9,1)
Audio
Antenna system .................................................. FM reception ....................................................... Installation of accessories.................................. Audio set ............................................................. Type A audio set ................................................. Type B audio set ................................................. In-dash 6 CD auto changer (Optional audio unit – if equipped)....................................................... Type A audio set (if equipped) ........................... Radio operation................................................... Compact disc player operation ............................
5-2
5-2
5-2
5-3
5-3
5-35-3
5-4
5-4
5-7CD changer control (if optional in-dash CD
changer is connected) .......................................
Type B audio set (if equipped).......................... Radio operation ................................................. Built-in CD changer control................................ Auxiliary unit and satellite radio operation.......... In-dash 6 CD auto changer (if equipped)......... Loading and unloading compact discs ...............
Precautions to observe when handling a
compact disc...................................................
5-9
5-11
5-11
5-15
5-20
5-23
5-235-25
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (166,1)
ing area, atmospheric conditions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary static, flutter or station inter- ference. reception continues to be unsatisfactory, switch to a stronger station.
If
Installation of accessories
Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or they are not suited for the vehicle.
if
5-2 Audio
Antenna system
The antenna is printed on the inner surface of the left side rear quarter window glass.
CAUTION
Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.
& FM reception Although FM is normally static free, reception can be affected by the surround-
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Audio set
& Type B audio set
Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details.
& Type A audio set
Black plate (167,1)
Audio 5-3
& In-dash 6 CD auto changer
(Optional audio unit – if equipped)
. Radio operation: refer to page 5-11
. Built-in CD changer operation: refer to page 5-15
. Auxiliary unit operation: refer to page 5- 20. Inserting and removing a disc or all discs: refer to page 5-23
. Radio operation: refer to page 5-4
. Compact disc player operation: refer to page 5-7
. CD changer control: refer to page 5-9北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (168,1)
5-4 Audio
Type A audio set (if equipped)
(1) Power switch, Volume control, Tone/
Fader/Balance control dial
The radio will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation
(2) BAND button (3) Tuning buttons (4) Preset buttons (5) AUDIO button (6) SCAN button
! Power switch and volume/bass/tre-
ble/fader/balance control (PWR/ VOL)
The dial (1) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. ! Tone and balance control The “VOLUME” control knob normally function as volume control. This knob become a control for Treble, Bass, Fader or Balance when you select the appro- priate audio mode. Choose desired volume level for each mode by turning the “VOLUME” control knob. The control function returns to volume control mode after approximately 5 seconds. To change control modes: Each brief the “AUDIO” button changes press of control modes in the following sequence starting from volume control mode. (When the radio is first the control
turned on,
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
mode is in the volume control.)
Display
Control mode
Black plate (169,1)
Audio 5-5
VOL
BAS
TRE
BAL
FAD
Volume control
Bass control
Treble control Balance control
Fader control
Turn counterclockwise
Turn clockwise
For less volume
For less bass sound
For less treble sound
For more volume
For more bass sound
For more treble sound
To increase left speaker volume and de- crease right speaker volume
To increase rear speaker volume and decrease front speaker volume
To increase right speaker volume and decrease left speaker volume To increase front speaker volume and decrease rear speaker volume
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-6 Audio
! FM/AM band selection button
(BAND)
Push the “BAND” button when the radio is on to select FM1, FM2 or AM band reception. Each time this button is pressed, the band will change in the following order:
The display indicates which one is cur- rently selected. ! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. ! Tuning (TUNE) ! Manual tuning (TUNE) Push the “ ” side of the tuning button (3) to increase the tuning frequency and press the “ the button to decrease it. Each time the button is pressed, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM wave- band. ! Seek tuning If is pressed for longer than half of a second, the radio will begin to automatically search for receiva-
the tuning button (3)
” side of
tuning to select
ble frequencies and will stop at the first one found. This function may not be available, however, when radio signals In such a situation, perform are weak. manual the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (6) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop- erly if the station reception is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (4) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset.
Black plate (170,1)
! How to preset stations 1. Press the “BAND” selection button to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (6) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (4) for at least 2 seconds to store the frequency. At this time, there will momentarily be no sound from the radio. the button is pressed for the preceding selection will remain in memory.
less than 2 seconds,
If
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. this occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
If is necessary to reset
it
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Compact disc player operation
Black plate (171,1)
Audio 5-7
(7) Disc slot (8) CD button (9) Eject button (10) Fast-forwarding and track up button (11) Fast-reversing and track down button (12) Random button (13) Repeat button (14) Scan button (15) PWR (power) switch
! To play back a compact disc ! When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A single CD (8 cm/3 inch CD) may also be used without any adapter. NOTE . Make sure to always insert a disc If a disc is with the label side up. inserted with the label side down, it might be ejected or the player might shut off. . After the last song finishes, the player will automatically return to track 1 (the first song on the disc).
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-8 Audio
! When CD is in the player Press the “CD” button (8). The display will show “CD-IN” and the player will start playback. NOTE After the last song finishes, playback will automatically return to track 1 (the first song on the disc). ! To stop playback of a CD When the “PWR” button (15) is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. ! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (11) to skip to the beginning of the current track. Each time this side of the button is pressed, the indicated track number will decrease.
” side of
” side of
the button (11)
the button (10)
! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Briefly press the “RPT” button (13) while a song is playing to play the song repeat- edly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. ! Random playback Briefly press the “RAND” button (12) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. the random mode, press the To cancel button again. Then the “RAND” indicator goes out, and normal playback mode is restored.
Black plate (172,1)
! Scan Briefly press the “SCAN” button (14), and you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored. ! To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
” (9). The disc will be ejected.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& CD changer control (if optional in-dash CD changer is con-
nected)
An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or unload CDs). See your SUBARU dealer for more information.
Black plate (173,1)
Audio 5-9
(16) CD button (17) Track selection buttons (18) RAND (Random) button (19) RPT (Repeat) button (20) SCAN button
! To start playback When the “CD” button (16) is pressed, the CD changer will start playback. The dis- play shows the current disc number, track number and the elapsed time during playback. NOTE . If a disc is in the player, the “DISC” button is used to change from CD player operation to DISC changer op- eration. Each time the “DISC” button is pressed, the operating mode will change alternately. . At the end of the disc, the player automatically continues with the next disc. . After playback on the last disc finishes, playback will automatically return to the first disc. . If you have loaded fewer than 6
discs, any missing disc is automati- cally skipped.– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-10 Audio
! Selection of a desired disc You can select a desired disc from among the discs contained in the CD changer only by pressing the corresponding num- ber on one of the disc select buttons. If you are to listen to the 5th disc in the CD changer, press the “5” button of the disc select buttons. All other discs in the CD changer can also be selected in a similar way. NOTE . No disc change takes place if the button corresponding to the storage tray in which no disc is loaded is pressed. . If the disc select button correspond- ing to the disc now in playback is pressed again, the disc will be replayed from its beginning. ! To select a song from its beginning ! Forward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (17) to skip to the beginning of the current
the disc,
” side of
the button (17)
track. Each time this side of the button is pressed, the indicated track number will decrease. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ continuously to fast-forward the disc. Release the button to stop fast-forwarding. If you continue fast-forwarding to the end of the CD changer will auto- matically stop fast-forwarding and start playback beginning with the first track on the current disc. ! Fast-reversing Press the “ continuously to fast-reverse the disc. Release the button to stop fast-reversing. If you continue fast-reversing to the beginning of the disc, the CD changer will automatically stop fast-reversing and start playback beginning with the first track on the current disc. ! Repeat playback Press the “RPT” button (19) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and
the button (17)
” side of
Black plate (174,1)
normal playback mode is restored. ! Random playback Press the “RAND” button (18) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored. ! Scan (a convenient way to become
familiar with a disc)
1. Press the “SCAN” button (20). – The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all programs. Then, normal playback starts. 2. Press the “SCAN” button again when you hear a track you like. – Normal playback resumes.
! To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Type B audio set (if equipped)
The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation
Black plate (175,1)
Audio 5-11
(1) Power switch, Volume, Brightness con-
trol dial
(2) FM/AM selection button (3) Seek button (4) Scan button (5) Sound/Tune control dial (6) Preset buttons
! Power switch and volume/bright-
ness control (POWER/VOL/ BRIGHT)
The dial (1) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial, and the volume is controlled by turning the dial. ! Sound control and tune/folder se-
lect/channel control (SOUND/TUNE/ FOLDER/CH)
The dial (5) is used for selecting the sound control mode with each brief press of the dial, and for adjusting each level by turning it. It is also used for tuning the radio/folder selection (only when playing MP3 or WMA)/channel selection (satellite radio*) when the “FM/AM”, “CD/AUX” and “SAT” are selected. (*: Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer.)
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (176,1)
5-12 Audio
Display
Control mode
BASS
MIDDLE
TREBLE
FADER
BALANCE
VOLUME
Bass control
Midrange control
Treble control Fader control
Balance control
Turn counterclockwise
Turn clockwise
For less bass sound
For more bass sound
For less midrange sound
For more midrange sound
For less treble sound
For more treble sound
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
To increase left speaker volume and de- crease right speaker volume
To increase right speaker volume and decrease left speaker volume
Volume control
For less volume
For more volume
! Sound control The dial (5) controls the Bass, Midrange, Treble, Balance and Fader when you select the appropriate sound control mode. Choose the desired setting for each mode by depressing the “SOUND” control dial function
(5). The control
returns to last mode after approximately 5 seconds. To change control modes: Each brief press of the “SOUND” button (5) changes control modes in the following sequence starting from bass control mode.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
! Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims when the light switch is in the “ ” or “ ” position. If this makes the display difficult to read, press the volume dial for more than 2 seconds to return the display to original brightness. Subsequently pressing the volume dial again for more than 2 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” position makes the radio display dim again. ! FM/AM selection button (FM/AM) Push the “FM/AM” button (2) when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:
” or “
The display indicates which one is cur- rently selected. ! Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. ! Manual tuning (TUNE) Turn the tuning dial (5) clockwise to increase the tuning frequency and turn
the dial counterclockwise to decrease it. Each click the dial is turned, the frequency changes 10 kHz in the AM waveband and 0.2 MHz in the FM waveband. ! Seek tuning When the “ ” side of the “SEEK/TRACK/ CAT” button (3) is depressed, the radio will begin to automatically seek up for recei- vable frequencies and will stop at the first one found. For the “ ” side, the radio will begin to automatically seek down. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (4) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at a receivable station for 5 seconds while displaying the frequency by blinking, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may
Black plate (177,1)
Audio 5-13
not function properly if the station recep- tion is weakened by distance from the station or proximity to tall buildings and hills. ! Selecting preset stations Presetting a station with a preset button (6) allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. ! How to preset stations 1. Press the “FM/AM” button (2) to select AM, FM1 or FM2 reception. 2. Press the “SCAN” button (4) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (6) for at least 2 seconds to store the frequency. The frequency of the station will flash once on the display at this time.
NOTE . If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the this preset buttons are cleared. occurs, the preset buttons. . If a cell phone is placed near the radio, it may cause the radio to emit
If is necessary to reset
it
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (178,1)
5-14 Audio
noise when the phone receives calls. This noise does not indicate a problem with the radio.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
& Built-in CD changer control
Black plate (179,1)
Audio 5-15
(7) CD button (8) Eject button (9) Disc slot (10) Track selection buttons (11) Repeat/Random button (12) Disc number indicator (13) Load button (14) Folder selection dial (15) Disc selection buttons (16) Display button
NOTE . Make sure to always insert a disc If a disc is with the label side up. inserted with the label side down, it might be ejected or the player might shut off. . If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. . The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones. . 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected.
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
Black plate (180,1)
5-16 Audio
it means that
! How to insert a CD(s) ! Inserting a CD 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator associated with the If no indicator idle position will blink. blinks, there is no idle position in the magazine. 2. When “IN” is displayed, insert the disc. Once you have inserted the disc, the disc number indicator will stop blinking. The disc will be then automatically drawn in, and the player will begin to play back the first track of the disc. . To insert more discs in succession, repeat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc within 15 seconds after you have pressed the “LOAD” button and “IN” is displayed, the player will begin to play back the first track of the last disc you have inserted. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter the standby mode. Press the “CD/AUX” button (7) to start playback.
! Inserting a disc in a desired position 1. Briefly press the “LOAD” button (13). If the magazine in the player has an idle position where you can insert a disc, the disc number indicator (12) associated with the idle position will blink. 2. Press the disc selection button (15) at the position where you want to insert a disc. The associated disc number indica- tor will blink. 3. If you insert a disc during the 15- second period while “IN” is displayed, the disc will be automatically drawn in, and the player will start playback of the disc, beginning with the first track. . To insert more discs in succession, repeat Steps 1 and 3. . While the player is in the loading mode, if you press the “FM/AM” button (2), the player will enter standby mode. Press the “CD/AUX” button (7) to start playback.
! Loading all the magazine (Full disc
loading mode) If you continue to press the “LOAD” 1. button (13) for more than 2 seconds, the player will enter the full disc loading mode. 2. The disc number indicator (12) asso- ciated with the idle position will blink. The magazine will be loaded with discs in the
ascending order of position number. 3. When the loading of a disc is com- plete, the next disc number indicator (12) will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15-second interval, the full disc loading mode will be can- celed, and the player will start playback of the disc inserted first.
! How to play back a CD or make a
pause
! When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first track. ! When there are CDs loaded: Depress the “CD/AUX” button to turn on the CD (when the last mode of the player is CD) and press a desired one of the disc select buttons (15). The player will then start playback of the selected CD, begin- ning with the first track.
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
! To select a track from its beginning ! Forward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase. ! Backward direction Briefly press the “ ” side of the button (10) to skip to the beginning of the current track. Each time the button is pressed, the indicated track number will decrease. ! To select a folder (for MP3/WMA
audio)
” side of
Turn the “TUNE/FOLDER/CH” dial (14) to select the folder. ! Fast-forwarding and fast-reversing ! Fast-forwarding Press the “ the button (10) continuously to fast-forward the disc. Release the button to stop fast-forwarding. ! Fast-reversing Press the “ the button (10) continuously to fast-reverse the disc. Release the button to stop fast-reversing. ! Repeat playback Depress the “RPT/RDM” button (11) while a song is playing to play the song
” side of
repeatedly. Each time this button is pressed, the repeat play mode will change in the following order:
The “RPT” indicator will come on and the song will be played continuously. When the “RPT” the repeat OFF is selected, indicator goes out and normal playback mode is restored. . The repeat play mode will be can- celled if you perform any of the follow- ing steps:
– Press the “RPT/RDM” button to select the repeat OFF. – Press the eject button. – Press the “LOAD” button. – Select the radio mode. – Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position. ! Random playback Press the “RPT/RDM” button (11) for more than 2 seconds while a disc is being played back to play all songs on the disc in a random order.
Black plate (181,1)
Audio 5-17
The “RDM” indicator will come on and all songs on the disc will be played in a random order. When the random OFF is the “RDM” indicator goes out selected, and normal playback mode is restored. . The random play mode will be cancelled if you perform any of the following steps:
– Press the “RPT/RDM” button to select the random OFF. – Press the eject button. – Press the “LOAD” button. – Select the radio mode. – Turn the “TUNE/FOLDER/CH” dial (for MP3/WMA audio). – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position.
! How to unload CDs from the player ! Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the disc select button (15) of the disc whose disc number indicator (12) is ON. 2. Press the eject button (8). Then the disc number indicator associated with the
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-18 Audio
disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1 and 2. If you press the eject button after turning OFF the ignition switch, only one disc will be ejected.
! Ejecting all discs from the player (All
disc ejection mode) If you continue to press the eject 1. button (8) for more than 2 seconds, the player will enter the all disc ejection mode. 2. Remove the disc that has been the display indicates “CD ALL ejected, EJECT” (when the ignition switch is in the “Acc” position) and disc indicator will blink. The other discs loaded will then be ejected one after another. If you do not remove the ejected disc within 15 sec- onds, the “All disc ejection mode” will be canceled.
NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
CAUTION
Do not attempt to insert two or more discs into the slot at a time. Doing
so can cause mechanical damage to the CD changer.
! Title display selection If you briefly press the “DISP” button (16) during playback, the indication will change to the next one in the following sequence. . For MP3/WMA:
. For Satellite radio:
The display mode that you selected will not be changed until you select the display mode again. When you depress the “DISP” button for more than 2 seconds, the title will be scrolled so you can see all of it. You will see 12 characters at a time. . The page scroll mode will be can- celled if you perform any of the follow- ing steps:
– When you do not operate any button within 10 seconds. – Press any button to select an- other play mode. – Press the eject button.
Black plate (182,1)
– Press the disc selection button. – Select the radio mode. – Press the “ – Turn off the power of the audio equipment. – Turn the ignition switch to the “LOCK” position.
” button.
” or “
NOTE When the disc has no title, the display indicates “NO TITLE”. ! When the following messages are
displayed
the following messages is If one of displayed while operating the CD player, determine the cause based on the follow- ing information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed This message means that there is a mechanical error. Depress the eject button to unload the disc. Check the disc for damage or deformation, and also check that the correct disc is inserted. Do not try to unload the disc forcibly. 8 cm/3 inch CDs are not supported, and if inserted, they will be immediately ejected and this the disc message will be displayed. cannot be unloaded or the message
If
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
remains displayed, please contact your SUBARU dealer. ! When “CHECK DISC” is displayed Press the eject button to unload the discs. Check that the disc is not damaged or scratched, and also check that the disc is inserted correctly. Some CD-RW discs may be causing this message to appear. Check that the disc type (i.e., 8 cm/3 inch CDs are not supported) and data format are correct. This player can only play MP3
and WMA data formats. If the disc cannot be unloaded or the message remains displayed, please contact your SUBARU dealer.Black plate (183,1)
Audio 5-19
– CONTINUED –
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
5-20 Audio
& Auxiliary unit and satellite radio operation
Black plate (184,1)
(17) AUX button (18) Category button (19) Scan button (20) Satellite radio* button (21) Category selection button (22 Preset buttons (23) Channel selection dial
(*: Use of satellite radio requires a tuner, antenna and a service contract. For de- tails, please contact your SUBARU deal- er.) NOTE . For use of the In-dash CD changer, refer to the section of “In-dash 6 CD auto changer” in this chapter. . Use of satellite radio requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer. . The “AUX mode” can be used when the appropriate device is connected to the AUX jack. . The output sound of the portable audio player is not loud, and the sound via the vehicle’s speakers that are connected to the vehicle audio set is very quiet. If you turn up the volume of the audio set, the volume becomes louder. However, when you change the audio to the radio mode or to a CD player, the sound becomes a lot louder. Remember to turn down the
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
volume when you change between them. ! AUX audio jack (if equipped) The AUX (auxiliary) audio jack is located behind the lid under the climate controls. Push gently on the lid to open it.
! Satellite Radio mode (if equipped) Press the “SAT” button (20) to select the “Satellite radio mode” (when the SR-BB is connected). ! Sirius satellite radio Sirius satellite radio is a recent innovation that allows the listener to experience digital sound quality and to have a greater variety of channels to choose from (more than 160 channels with the relevant subscription). Use of satellite radio (Sirius) requires a tuner, antenna and a service contract. For details, please contact your SUBARU dealer or visit Sirius Satellite Radio at www.sirius.com or call 1-888-539-SIRIUS (7474) for more information. Sirius, the Sirius dog logo, channel names and logos are trademarks of SIRIUS Satellite Radio Inc. ! Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may obstruct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result loss include driving near a wall, steep cliff or hill, or driving on the lower level of a multi- tiered road or inside a parking garage.
in signal
Black plate (185,1)
Audio 5-21
To help reduce this condition, satellite radio providers have installed ground- based repeaters in heavily populated areas. However, you may still experience reception problems in some areas. ! Displaying satellite radio ID of tuner When you activate satellite radio, you should have your satellite radio tuner ID ready because each tuner is identified by its unique satellite radio tuner ID. The satellite radio ID will be needed when you activate satellite radio and receive satellite radio customer support. The satellite radio ID can be found on the audio display by tuning the channel to “0”. Turn the “TUNE/FOLDER/CH” dial (23) to select the satellite radio channel. ! Channel selection Turn the “TUNE/FOLDER/CH” dial (23) to select the radio channel. Turn the tuning dial clockwise to change the channel upward and turn the dial counterclockwise to change the channel downward with each click of the dial. ! Category selection Press the “SEEK/TRACK/CAT” button (18) radio channel. Press the “ ” side of the button (18) to change the category upward and the “ ” side of the button to downward – CONTINUED –
the category of
to select
北米Model "A8130BE-B" EDITED: 2007/ 7/ 25
selection, channel scan) are performed only in the selected category. To cancel the category mode, press the “CAT” button (21) for at least 2 seconds again. ! Band selection Push the “SAT” button (20) when the radio is on to select SR1, SR2 or SR3 reception. Each time this button is pressed, the band will change in the following order:
! AUX mode Press the “CD/AUX” button (17) to select the “AUX mode” (when the AUX unit is connected to the AUX jack).
5-22 Audio
with each press of the button. ! Channel preset Presetting a channel with a preset button (22) allows you to select that station in a single operation. Up to six SR1, SR2 and SR3 channels each may be preset. Press one of the preset buttons for at least 2 seconds to store the channel. The number of the channel will flash once on the display, and the unit produces a beep sound at this time. ! Channel scan Press the “SCAN” button (19) to change the radio to the SCAN mode. In this mode, the radio scans through the channel until a station is found. The radio will stop at the
