Login- Download PDF Manual
-
schedule in the “Warranty and Maintenance Booklet”.
– CONTINUED –
11-19
FORESTER (NA) A8050BE–A (ENG.)
B Recommended spark plugs
RC10YC4 (Champion) BKR6E-11 (NGK) BKR5E-11 (NGK)
Drive belts
The alternator, power steering pump, and air conditioner compressor de- pend on drive belts. Satisfactory performance requires that belt tension be correct.
HGA005BB
Deflection
in. (mm)
New belt
0.28 — 0.35
(7.0 — 9.0)0.30 — 0.33
(7.5 — 8.5)Used belt
0.35 — 0.43
(9.0 — 11.0)0.35 — 0.40
(9.0 — 10.0)To check belt tension, place a straightedge (ruler) across two adjacent pulleys and apply a force of 98 N (22 lb, 10 kg) midway between the pulleys by using a spring scale. Belt deflection should be the amount
11-20
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
specified. If a belt is loose, cracked, or worn, contact your SUBARU dealer.
Manual transmission oil
B Checking the oil level Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine.
Upper level
Lower level
HSA002CB
OM-H0210
2. Pull out the dipstick, wipe it clean, and insert it again. 3. Pull out the dipstick again and check the oil level on it. If it is below the lower level, add oil through the dipstick hole to bring the level up to the upper level.
B Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together.
11
Oil grade: API classification GL-5
– CONTINUED –
11-21
FORESTER (NA) A8050BE–A (ENG.)
SAE viscosity No. and Applicable Temperature
OM-H0205
Automatic transmission fluid
B Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the dipstick.
Though the fluid level can be checked without warming up the fluid on the “COLD” range, we recommend checking the fluid level when the fluid is at operating temperature.
n Checking the fluid level when the fluid is hot Check the fluid level monthly. 1. Drive the vehicle several miles to raise the temperature of the transmission fluid up to normal operating temperature; 140 to 176°F (60 to 80 °C) is normal. 2. Park the vehicle on a level surface and set the parking brake. 3. First shift the selector lever in each position. Then shift it in the “P” position, and run the engine at idling speed.
11-22
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
HSA002DB
HBA008BB
4. Pull out the dipstick and check the fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended au- tomatic transmission fluid up to the upper level.
n Checking the fluid level when the fluid is cold When the fluid level has to be checked without time to warm up the automatic transmission, check to see that the fluid level is between the lower level and upper level on the “COLD” range. If it is below that range, add fluid up to the upper level. Be careful not to overfill.
B Recommended fluid
“Dexron III” Type Automatic Transmission Fluid
11
– CONTINUED –
11-23
FORESTER (NA) A8050BE–A (ENG.)
Front differential gear oil (Automatic transmission vehicles)
B Checking the oil level Check the differential oil level monthly.
HSA002EB
HBA010BB
1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again. 3. Pull out the dipstick again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.
B Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together.
Oil grade: API classification GL-5
11-24
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
SAE viscosity No. and Applicable Temperature
OM-H0212
Rear differential gear oil
B Checking the oil level
CAUTION
If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.
Your vehicle may be equipped with a rear differential protector. The differential protector provides protection to the rear differential assem- bly during off-road use. Removal of the rear differential protector is not required when checking the oil level.
11
– CONTINUED –
11-25
FORESTER (NA) A8050BE–A (ENG.)
Filler hole
Oil level
Drain hole
HB0077
Filler hole
Drain hole
HB0078
Remove the plug from the filler hole and check the oil level. The oil level should be kept even with the bottom of the filler hole. If the oil level is below the bottom edge of the hole, add oil through the filler hole to raise the level.
B Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together.
Oil grade: API classification GL-5
SAE viscosity No. and Applicable Temperature
OM-H0205
11-26
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Power steering fluid
The power steering fluid expands greatly as its temperature rises; the fluid level differs according to fluid temperature. Therefore, the dipstick has two different checking ranges for hot and cold fluids.
B Checking the fluid level when the fluid is hot
WARNING
Be careful not to burn yourself because the fluid may be hot.
CAUTION
D When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank. And never use different brands together. D Avoid spilling fluid when adding it in the tank.
Check the power steering fluid level monthly. 1. Drive the vehicle several miles to raise the temperature of the pow- er steering fluid up to normal operating temperature, about 140°F (60°C). 2. Park the vehicle on a level surface, and stop the engine. 3. Turn the reservoir cap counterclockwise to remove the fluid level dipstick, wipe the dipstick clean, and reinsert it.
11
Specified range
HS0185
Specified range
HS0186
– CONTINUED –
11-27
FORESTER (NA) A8050BE–A (ENG.)
4. Remove the dipstick again and check the fluid level on it. If it is below the lower level of the “HOT” range, add the recommended steering fluid up to the specified range of the dipstick.
If the fluid level is extreme low, it may indicate possible leakage. Con- sult your SUBARU dealer for inspection.
B Checking the fluid level when the fluid is cold When the fluid level has to be checked without warming up the power steering system (approximately 70°F [21°C]), read the fluid level on the “COLD” range.
B Recommended fluid
“Dexron III” Type Automatic Transmission Fluid
Brake fluid
B Checking the fluid level
WARNING
D Never let brake fluid contact your eyes because brake fluid can be harmful to your eyes. If brake fluid gets in your eyes, immedi- ately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable. D Brake fluid absorbs moisture from the air. Any absorbed mois- ture can cause a dangerous loss of braking performance. D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.
11-28
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
CAUTION
D Never use different brands of brake fluid together. D When adding brake fluid, be careful not to allow any dirt into the reservoir. D Never splash the brake fluid over painted surfaces or rubber parts. Alcohol contained in the brake fluid may damage them.
Check the fluid level monthly.
HSA004BB
Check the fluid level on the outside of the reservoir. If the level is be- low “MIN”, add the recommended brake fluid to “MAX”. Use only brake fluid from a sealed container.
B Recommended brake fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluid
11
– CONTINUED –
11-29
FORESTER (NA) A8050BE–A (ENG.)
Clutch fluid
WARNING
Never let clutch fluid contact your eyes because clutch fluid can be harmful to your eyes. If clutch fluid gets in your eyes, immedi- ately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is advisable.
CAUTION
D Clutch fluid absorbs moisture from the air. Any absorbed moisture can cause improper clutch operation. D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. D Never use different brands of clutch fluid together. D When clutch fluid is added, be careful not to allow any dirt into the tank.
Check the fluid level on the outside of the reservoir. If the level is below “MIN” level mark, add the recommended clutch fluid to “MAX” level mark. Use only clutch fluid from a sealed container.
HSA002FB
11-30
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
B Recommended clutch fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluid
Brake booster
If the brake booster does not operate as described below, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary. 2. With the brake pedal depressed, start the engine. The pedal should move slightly down to the floor. 3. With the brake pedal depressed, stop the engine and keep the pedal depressed for 30 seconds. The pedal height should not change. 4. Start the engine again and run for about one minute then turn it off. Depress the brake pedal several times to check the brake booster. Brake booster operates properly if the pedal stroke decreases with each depression.
Battery
WARNING
D Before beginning work on or near any battery, be sure to extin- guish all cigarettes, matches, and lighters. Never expose a bat- tery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. D For safety, in case an explosion does occur, wear eye protec- tion or shield your eyes when working near any battery. Never lean over a battery. D Do not let battery fluid contact eyes, skin, fabrics, or paint be- cause battery fluid is a corrosive acid. If battery fluid gets on your skin or in your eyes, immediately flush the area with water thor- oughly. Seek medical help immediately if acid has entered the eyes.
– CONTINUED –
11-31
11
FORESTER (NA) A8050BE–A (ENG.)
D To lessen the risk of sparks, remove rings, metal watchbands, and other metal jewelry. Never allow metal tools to contact the positive battery terminal and anything connected to it WHILE you are at the same time in contact with any other metallic portion of the vehicle because a short circuit will result. D Keep everyone including children away from the battery. D Charge the battery in a well-ventilated area. D Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after han- dling.
CAUTION
Never use more than 10 amperes when charging the battery be- cause it will shorten battery life.
B Checking the fluid level
Cap
Upper level
Lower level
OM-H1048
It is unnecessary to periodically check the battery fluid level or peri- odically refill with distilled water. However, if the battery fluid level is below the lower level, remove the cap. Fill to the upper level with distilled water.
11-32
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Windshield washer fluid
CAUTION
Never use engine coolant as washer fluid because it could cause paint damage.
Check the level of the washer fluid at each fuel stop. If the level is low, fill the fluid up to the neck of the reservoir. Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing temperature varies according to how much it is diluted, as indicated below.
Washer Fluid Concentration
Freezing Temperature
30% 50% 100%
10.4°F (–12°C) –4 °F (–20°C) –49°F (–45°C)
11
HS0189
– CONTINUED –
11-33
FORESTER (NA) A8050BE–A (ENG.)
Replacement of windshield wiper blades
Grease, wax, insects, or other materials on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water.
CAUTION
Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.
If you cannot eliminate the streaking even after following this method, replace the wiper blades using the following procedures: 1. Raise the wiper arm off the windshield. 2. Remove the wiper blade assembly by holding its pivot area and push- ing it in the direction shown by the arrow while depressing the wiper blade stopper.
Stopper
HS0190
3. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the metal support.
11-34
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Metal support
HS0191
4. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.
Metal spines
HS0192
5. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks. Be sure to position the claws at the end of the metal support between the stoppers on the rubber as shown. If the rubber is not retained properly, the wiper blade may scratch the windshield.
11
– CONTINUED –
11-35
FORESTER (NA) A8050BE–A (ENG.)
Stopper
HS0193
HS0194
6. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 7. Lower the wiper arm.
11-36
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Brake pedal
Check the brake pedal free play and reserve distance according to the maintenance schedule in the “Warranty and Maintenance Booklet”.
B Checking the brake pedal free play
0.04 — 0.12 in (1.0 — 3.0 mm)
OM-H0224
Stop the engine and firmly depress the brake pedal several times. Lightly press the brake pedal down with one finger to check the free play with a force of less than 10 N (2 lb, 1 kg). If the free play is not within proper specification, contact your SUBARU dealer.
B Checking the brake pedal reserve distance
More than 2.56 in (65 mm)
11
Depress the pedal with a force of approximately 294 N (66 lb, 30 kg)
OM-H0225
– CONTINUED –
11-37
FORESTER (NA) A8050BE–A (ENG.)
and measure the distance between the upper surface of the pedal pad and the floor. When the measurement is smaller than the specification, or when the pedal does not operate smoothly, contact with your SUBARU dealer.
Clutch pedal (Manual transmission vehicles)
Check the clutch pedal free play and reserve distance according to the maintenance schedule in the “Warranty and Maintenance Booklet”.
B Checking the clutch function Check the clutch engagement and disengagement. 1. With the engine idling, check that there are no abnormal noises when the clutch pedal is depressed, and that shifting into 1st or re- verse feels smooth. 2. Start the vehicle by releasing the pedal slowly to check that the en- gine and transmission smoothly couple without any sign of slippage.
B Checking the clutch pedal free play
0.16 — 0.51 in (4.0 — 13.0 mm)
OM-H0224
Lightly press the clutch pedal down with your finger until you feel re- sistance, and check the free play. If the free play is not within proper specification, contact your SUBARU dealer.
11-38
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Replacement of brake pad and lining
CAUTION
If you continue to drive despite the scraping noise from the audi- ble brake pad wear indicator, it will result in the need for costly brake rotor repair or replacement.
OM-H0163
The front disc brakes and the right side rear disc brake have audible wear indicators on the brake pads. If the brake pads wear close to their service limit, the wear indicator makes a very audible scraping noise when the brake pedal is applied.
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as pos- sible.
B Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts. After replacement, the new parts must be broken in as follows:
n Brake pad and lining While maintaining a speed of 30 to 40 mph (50 to 65 km/h), step on the brake pedal lightly. Repeat this five or more times.
11
– CONTINUED –
11-39
FORESTER (NA) A8050BE–A (ENG.)
n Parking brake lining
WARNING
A safe location and situation should be selected for break-in driv- ing.
CAUTION
Pulling the parking brake lever too forcefully may cause the rear wheels to lock. To avoid this, be certain to pull the lever up slowly and gently.
1. Drive the vehicle at a speed of about 22 mph (35 km/h). 2. With the parking brake release button pushed in, pull the parking brake lever SLOWLY and GENTLY. (Pulling with a force of approxi- mately 147 N [33 lb, 15 kg].) 3. Drive the vehicle for about 220 yards (200 meters) in this condition. 4. Wait 5 to 10 minutes for the parking brake to cool down. Repeat this procedure. 5. Check the parking brake stroke. If the parking brake stroke is out of the specified range, adjust it by turning the adjusting nut located on the parking brake lever.
Parking brake stroke: 7 — 8 notches / 196 N (44 lb, 20 kg)
Parking brake stroke
Check the parking brake stroke according to the maintenance schedule in the “Warranty and Maintenance Booklet”. When the parking brake is properly adjusted, braking power is fully applied by pulling the lever up seven to eight notches gently but firmly (about 196 N, 44 lb, 20 kg). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer.
11-40
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
7 to 8 notches
HS0199
Tires and wheels
J Types of tires
B All season tires All season tires are designed to provide an adequate measure of trac- tion, handling and braking performance in year-round driving includ- ing snowy and icy road conditions. However all season tires do not have adequate traction performance compared with winter (snow) tires in heavy or loose snow or on icy road. All season tires are identified by “ALL SEASON” and/or “M+S” (Mud & Snow) on the tire sidewall.
B Summer tires Summer tires are high-speed capability tires best suited for highway driving under dry conditions. Summer tires are inadequate for driving on slippery roads such as on snow-covered or icy roads. If you drive your vehicle on snow-covered or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to replace all four tires.
11
– CONTINUED –
11-41
FORESTER (NA) A8050BE–A (ENG.)
B Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not have adequate performance compared with summer tires and all season tires on roads other than snow-covered and icy roads.
J Tire inspection Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Contact your SUBARU dealer immediately if you find any problem.
NOTE D When the wheels and tires strike curbs or are subjected to harsh treatment as when the vehicle is driven on a rough surface, they can suffer damage that cannot be seen with the naked eye. This type of damage does not become evident until time has passed. Try not to drive over curbs, potholes or other rough surfaces. If doing so is un- avoidable, keep the vehicle’s speed down to a walking pace or less, and approach the curbs as squarely as possible. Also, make sure the tires are not pressed against the curbs when you park the ve- hicle. D If you feel unusual vibration while driving or find it difficult to steer the vehicle in a straight line, one of the tires and/or wheels may be damaged. Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected.
J Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’ service lives and is essential for good running performance. Check and, if nec- essary, adjust the pressure of each tire (including the spare) at least once a month (for example, during a fuel stop) and before any long jour- ney.
Check the tire pressures when the tires are cold. Use a pressure gauge to adjust the tire pressures to the values shown on the tire placard. The tire placard is located on the door pillar on the driver’s side.
11-42
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
HS0251
Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the ambient tempera- ture. It is best to check tire pressure outdoors before driving the vehicle.
When a tire becomes warm, the air inside it expands, causing the tire pressure to increase. Be careful not to mistakenly release air from a warm tire to reduce its pressure.
NOTE D The air pressure in a tire increases by approximately 4.3 psi (30
kPa, 0.3 kg/cm2) when the tire becomes warm. D The tires are considered cold when the vehicle has been parked for at least three hours or has been driven less than one mile (1.6
km).WARNING
Do not let air out of warm tires to adjust pressure. Doing so will result in low tire pressure.
11
Incorrect tire pressures detract from controllability and ride comfort, and they cause the tires to wear abnormally.
– CONTINUED –
11-43
FORESTER (NA) A8050BE–A (ENG.)
D Correct tire pressure (tread worn evenly)
HGB033AA
Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower.
D Abnormally low tire pressure (tread worn at shoulders)
HSB012AA
Rolling resistance is high, so fuel consumption is also higher.
11-44
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
D Abnormally high tire pressure (tread worn in center)
HSB013AA
Ride comfort is poor. Also, the tire magnifies the effects of road-sur- face bumps and dips, possibly resulting in vehicle damage.
If the tire placard shows tire pressures for the vehicle when fully loaded and for the vehicle when towing a trailer, adjust the tire pressures to the values that match current loading conditions.
WARNING
Driving at high speeds with excessively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident.
J Wheel balance Each wheel was correctly balanced when your vehicle was new, but the wheels will become unbalanced as the tires become worn during use. Wheel imbalance causes the steering wheel to vibrate slightly at certain vehicle speeds and detracts from the vehicle’s straight-line stability. It can also cause steering and suspension systems problems and abnor- mal tire wear. If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation.
– CONTINUED –
11-45
11
FORESTER (NA) A8050BE–A (ENG.)
NOTE Loss of correct wheel alignment* causes the tires to wear on one side and reduces the vehicle’s running stability. Contact your SUBARU dealer if you notice abnormal tire wear.
* : The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering performance.
J Wear indicators Each tire incorporates a tread wear indicator, which becomes visible when the depth of the tread grooves decreases to 0.063 in. (1.6 mm). A tire must be replaced when the tread wear indicator appears as a solid band across the tread.
A) New tread B) Worn tread 1) Tread wear indicator
OM-H0231
WARNING
When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immedi- ately. With a tire in this condition, driving at high speeds in wet weather can cause the vehicle to hydroplane. The resulting loss of vehicle control can lead to an accident.
NOTE For safety, inspect the tire tread regularly and replace the tires be- fore their tread wear indicators become visible.
11-46
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
J Tire rotation
OM-H0230
Tire wear varies from wheel to wheel. To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,500 km). Rotating the tires involves switching the front and rear tires on the right-hand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle. (Each tire must be kept on its original side of the vehicle.) Replace any damaged or unevenly worn tire at the time of rotation. After tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tightened. After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose.
J Tire replacement The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbitrarily. The tires fitted as standard equipment are optimally matched to the characteristics of the vehicle and were selected to give the best possible combination of running per- formance, ride comfort, and service life. It is essential for every tire to have a size and construction matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard. Using tires of a non-specified size detracts from controllability, ride com- fort, braking performance, speedometer accuracy and odometer accu-
– CONTINUED –
11-47
11
FORESTER (NA) A8050BE–A (ENG.)
racy. It also creates incorrect body-to-tire clearances and inappropriately changes the vehicle’s ground clearance.
All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equipment.
For safe vehicle operation, SUBARU recommends replacing all four tires at the same time.
WARNING
D All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, degree of wear, speed symbol, load index and size. Mixing tires of different types, sizes or degrees of wear can result in damage to the vehicle’s power train. Use of dif- ferent types or sizes of tires can also dangerously reduce con- trollability and braking performance and can lead to an accident. D Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously reduce controllability, resulting in an accident.
J Wheel replacement When replacing wheels due, for example, to damage, make sure the re- placement wheels match the specifications of the wheels that are fitted as standard equipment. Replacement wheels are available from SUBARU dealers.
WARNING
Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper op- eration and may cause the tires to rub against the wheel well housing during turns. The resulting loss of vehicle control could lead to an accident.
11-48
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Aluminum wheels (If equipped)
Aluminum wheels can be scratched and damaged easily. Handle them carefully to maintain their appearance, performance, and safety.
D When any of the wheels is removed and replaced for tire rotation or to change a flat, always check the tightness of the wheel nuts after driving approximatly 600 miles (1,000 km). If any nut is loose, tighten it to the specified torque. D Never apply oil to the threaded parts, wheel nuts, or tapered surface of the wheel. D Never let the wheel rub against sharp protrusions or curbs. D Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. D When wheel nuts, balance weights, or the center cap are replaced, be sure to replace them with genuine SUBARU parts designed for alumi- num wheels.
Fuses
11
HS0202
HS0203
The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse boxes. If any lights, accessories or other electrical controls do not operate, in- spect the corresponding fuse. If a fuse has blown, replace it.
– CONTINUED –
11-49
FORESTER (NA) A8050BE–A (ENG.)
Good
Blown
HS0204
CAUTION
Never replace a fuse with one having a higher rating or with mate- rial other than a fuse because serious damage or a fire could re- sult.
B Fuse box (behind the coin tray) 1. Turn the ignition switch to the “LOCK” position and turn off all elec- trical accessories.
HS0202
2. Open the coin tray and pull it horizontally to remove it. 3. Determine which fuse may be blown. The back side of the coin tray and the “Fuse and circuits” section in chapter 12 in this manual show the circuit for each fuse.
11-50
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Fuse puller
HS0207
HSB011BB
4. Pull out the fuse with the fuse puller. The fuse puller is stored in the main fuse box cover in the engine compartment. 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. The spare fuses are stored in the main fuse box cover in the engine compartment. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs.
B Main fuse box (in the engine compartment) 1. Turn the ignition switch to the “LOCK” position and turn off all elec- trical accessories. 2. Open the engine hood. 3. Remove the main fuse box cover. 4. Determine which fuse may be blown. The fuse box cover and “Fuse and circuits” section in chapter 12 in this manual show the cir- cuit for each fuse.
11
– CONTINUED –
11-51
FORESTER (NA) A8050BE–A (ENG.)
Fuse puller
HS0207
HSB011BB
5. Pull out the fuse with the fuse puller provided in the main fuse box cover. 6. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. The spare fuses are stored in the main fuse box cover in the engine compartment. 7. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs.
11-52
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
Main fuse
HS0203
The main fuses are designed to melt during an overload to prevent dam- age to the wiring harness and electrical equipment. Check the main fuses if any electrical component fails to operate (except the starter mo- tor) and other fuses are good. A melted main fuse must be replaced. Use only replacements with the same specified rating as the melted main fuse. If a main fuse blows after it is replaced, have the electrical system checked by your nearest SUBARU dealer.
Installation of accessories
Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
11
– CONTINUED –
11-53
FORESTER (NA) A8050BE–A (ENG.)
Replacing bulbs
HSF015FB
Wattage (12V-8W) (12V-8W)
(12V-27/8W Amber) (12V-51W) (12V-60/55W) (12V-13W) (12V-18W) (12V-21W Amber) (12V-21/5W) (12V-5W) (12V-5W)
HSF014CB
Bulb No. — —
1157NA 9006
HB2 (H4) 912
921
— 7443
168
1681 Spot light 2 Room light 3 Front turn signal, parking light
and front side marker light
4 Fog light 5 Headlight 6 High mount stop light 7 Backup light 8 Rear turn signal light 9 Brake/tail light Q Tail light W License plate light
11-54
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
J Headlight
CAUTION
Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface develop into hot spots, caus- ing the bulb to break. If there are finger prints or grease on the bulb surface, wipe them away with a soft cloth moistened with al- cohol.
NOTE If headlight aiming is required, consult your SUBARU dealer for proper adjustment of the headlight aim.
HSB004BB
HSB005BB
1. Disconnect the electrical connector, then remove the rubber cover. 2. Remove the retainer spring. 3. Replace the bulb, then set the retainer spring securely. 4. Install the rubber cover with the top mark facing up, then reconnect the electrical connector.
11
– CONTINUED –
11-55
FORESTER (NA) A8050BE–A (ENG.)
J Fog light (if equipped)
CAUTION
Halogen light bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface develop into hot spots, causing the bulb to break. If there are finger prints or grease on the bulb sur- face, wipe them away with a soft cloth moistened with alcohol.
B To remove and install the fog light protector
HS0213
HS0214
1. Unhook the lower part of the fog light protector by pulling the hook down. 2. Pull the protector to remove it. 3. To install the protector, first insert the upper part of the protector into the gap between the fog light and body, then push the lower part of the protector until it clicks. 4. Make sure that the protector is locked in place by pulling it lightly.
11-56
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
B Bulb replacement
HS0215
HSB006BA
1. Remove the fog light protector. 2. Remove the fog light assembly by removing the two screws. 3. Disconnect the connector. 4. Remove the fog light bulb by turning it counterclockwise. 5. Replace the bulb with a new one. Then reconnect the connectors and reinstall the removed parts in the reverse order of removal.
J Front turn signal, parking light and front side marker
light
11
HS0217
1. Remove the front turn signal light assembly mounting screw located at the top of the headlight assembly using a phillips screwdriver. 2. Move the front turn signal light assembly forward until it pops out from
– CONTINUED –
11-57
FORESTER (NA) A8050BE–A (ENG.)
the fender. 3. Remove the bulb holder from the front turn signal light assembly by turning it counterclockwise. 4. Pull the bulb out of the socket. Install a new bulb. 5. Set the bulb holder into the front turn signal light assembly and turn it clockwise until it locks. 6. Set the front turn signal light assembly into the fender. Tighten the mounting screw.
J Rear combination lights
B Brake/tail and rear turn signal light
HS0218
HSB007BA
1. Unlatch the rear combination light cover by pulling the knob. Open the cover up. 2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 3. Remove the bulb from the socket. Turn signal: Pushing it and turning counterclockwise. Brake/tail: Pull the bulb out of the socket. Install a new bulb. 4. Set the bulb holder into the rear combination light assembly and turn it clockwise until it locks. 5. Close the cover and latch the lock.
11-58
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
B Back-up/tail light (in the rear gate)
HSB002BB
HSA020BA
1. Remove the rear combination light cover by prying the edge of the cover with screwdriver. 2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 3. Pull the bulb out of socket. Install a new bulb. 4. Set the bulb socket into the rear combination light and turn it clock- wise untill it locks.
J License plate light
11
HS2009CA
1. Remove the mounting screws using a phillips screwdriver. 2. Remove the cover and lens. 3. Pull the bulb out of the socket. Install a new bulb.
– CONTINUED –
11-59
FORESTER (NA) A8050BE–A (ENG.)
4. Reinstall the lens and cover. 5. Tighten the mounting screws.
J Interior light and luggage compartment light
HS0221
HSA005BA
HS0223
1. Remove the lens by prying the edge of the lens with a regular screw- driver. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the lens.
11-60
FORESTER (NA) A8050BE–A (ENG.)
Maintenance and service
J Spot light
HSA006BA
1. Remove the lens by prying the edge of the lens with a regular screw- driver. 2. Remove the plate by removing a mounting screw. 3 Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the plate and the lens.
J High mount stop light
11
OM-H0355
1. Remove the mounting screw covers by prying on the edge with a screwdriver. 2. Remove the mounting screws using a phillips screwdriver and then remove the high mount stop light cover. 3. Pull the bulb out of the socket. Install a new bulb.
– CONTINUED –
11-61
FORESTER (NA) A8050BE–A (ENG.)
4. Reinstall the cover. 5. Tighten the mounting screws then reinstall the covers.
NOTE Other bulbs may be difficult to replace. Have your SUBARU dealer replace these bulbs if necessary.
11-62
FORESTER (NA) A8050BE–A (ENG.)
Specifications
Specifications Dimensions Engine Electrical system Capacities Tires Wheel alignment Fuses and circuits
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse panel located behind the coin tray Fuse panel located in the engine compartment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulb chart Vehicle identification
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-2
12-2
12-2
12-2
12-3
12-3
12-3
12-4
12-4
12-6
12-7
12-812
FORESTER (NA) A8050BE–A (ENG.)
Specifications
These specifications are subject to change without notice.
J Dimensions Overall length Overall width Overall height Ground clearance Front tread Rear tread Wheelbase
J Engine
Engine model Engine type
Engine displacement Bore Stroke Compression ratio Firing order
J Electrical system
Battery Type
Reserve capacity Cold cranking ampere Alternator Spark plugs
Spark plug gap
12-2
175.6 in. (4,460 mm) 68.3 in. (1,735 mm) 62.8 in. (1,595 mm) 7.5 in. (190 mm) 58.1 in. (1,475 mm) 57.7 in. (1,465 mm) 99.4 in. (2,525 mm)
EJ251
Horizontally opposed, liquid cooled 4 cylinder, 4 stroke gasoline engine 149.9 cu in. (2,457 cc) 3.92 in. (99.5 mm) 3.11 in. (79.0 mm) 10.0 : 1
1 - 3 - 2 - 4MT: 55D23L, AT: 75D23L MT: 99 min., AT: 118 min. MT: 356 amp., AT: 520 amp. 12V - 75A RC10YC4 (Champion), BKR6E-11 (NGK), BKR5E-11 (NGK) 0.039 to 0.043 in. (1.0 to 1.1 mm)
FORESTER (NA) A8050BE–A (ENG.)
Specifications
J Capacities
Fuel tank Engine oil Manual transmission oil Automatic transmission fluid AT differential gear oil AWD rear differential gear oil Power steering fluid Engine coolant
15.9 US gal (60 liter, 13.2 Imp gal) 4.2 US qt (4.0 liter, 3.5 Imp qt) 3.7 US qt (3.5 liter, 3.1 Imp qt) 9.8 US qt (9.3 liter, 8.2 Imp qt) 1.3 US qt (1.2 liter, 1.1 Imp qt) 0.8 US qt (0.8 liter, 0.7 Imp qt) 0.7 US qt (0.7 liter, 0.6 Imp qt) 6.6 US qt (6.2 liter, 5.5 Imp qt)
J Tires
Type Size
Pressure
Wheel size
Steel belted radial, Tubeless P205/70 R15 95S P215/60 R16 94H See the tire inflation pressure label located under the driver’s door latch. 15 x 6J, 16 x 61/2 JJ
J Wheel alignment
Toe
Camber
Front Rear Front Rear
0 " 0.12 in. (0 " 3 mm) 0.08 " 0.12 in. (2 " 3 mm) –0°15’ –0°35’
12
– CONTINUED –
12-3
FORESTER (NA) A8050BE–A (ENG.)
Fuses and circuits
J Fuse panel located behind the coin tray
1 2 3 4 5 6
7 8 9 Q
W E
T Y U I O P
Fuse panel
Fuse rating Circuit
HS0224
D Heater fan
D Heater fan
D Power door lock
D Cigarette lighter D Remote controlled rear view mirrors
D Tail light D Parking light
D SRS airbag
D Fog light
D ABS solenoid
D Radio D Clock
15A
15A
15A
20A
10A
15A
15A
20A
15A
10
Empty
12-4
FORESTER (NA) A8050BE–A (ENG.)
Specifications
Fuse panel
Fuse rating
Circuit
11
12
13
14
15
16
17
18
19
15A
10A
15A
Empty
20A
20A
15A
15A
20A
D Engine ignition system D SRS airbag
D Illumination brightness control
D Wiper deicer
D Windshield wiper and washer D Rear window wiper and washer
D Brake light
D Air conditioner
D Backup light D Cruise control D ABS control
D Rear accessory power socket D Seat heater
12
– CONTINUED –
12-5
FORESTER (NA) A8050BE–A (ENG.)
J Fuse panel located in the engine compartment
FWD socket
D F
Main fuse
HS0225
Fuse panel
Fuse rating Circuit
20A
20A
20A
15A
15A
10A
10A
15A
15A
20A
15A
D Radiator cooling fan (Main)
D Radiator cooling fan (Sub)
D Rear window defogger
D Hazard warning flasher D Horn
D Meter D SRS airbag system warning light
D Automatic transmission control unit
D Alternator
D Headlight (right side)
D Headlight (left side)
D Lighting switch
D Clock D Interior light
20
21
22
23
24
25
26
27
28
29
30
12-6
FORESTER (NA) A8050BE–A (ENG.)
Specifications
Wattage 12V-8W 12V-8W
12V-27/8W Amber 12V-51W 12V-60/55W 12V-21/5W 12V-21W Amber 12V-18W 12V-13W 12V-5W 12V-5W
Bulb No. — —
1157NA 9006
HB2 (H4) 7443
— 921
912
168
168Bulb chart
Description Spot light Room light Front turn signal, parking light and front side marker light Fog light Headlight Brake/tail light Rear turn signal light Backup light High mount stop light License plate light Tail light
12
– CONTINUED –
12-7
FORESTER (NA) A8050BE–A (ENG.)
Vehicle identification
Emission control label
Vacuum hose piping label
Vehicle identification number plate
Tire inflation pressure label
Vehicle identification number
Model number plate
Certification plate
Bar cord label
HS0226
12-8
FORESTER (NA) A8050BE–A (ENG.)
Consumer information and Reporting safety defects
Uniform tire quality grading standards
Treadwear Traction AA, A, B, C Temperature A, B, C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reporting safety defects (USA)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-2
13-2
13-2
13-3
13-413
FORESTER (NA) A8050BE–A (ENG.)
For U.S.A. The following information has been compiled according to Code of Fed- eral Regulations “Title 49, Part 575”.
Uniform tire quality grading standards
This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance. This is to aid the consumer in making an informed choice in the purchase of tires. Quality grades can be found where applicable on the tire sidewall be- tween the tread shoulder and maximum section width. For example:
Treadwear 200 Traction AA Temperature A
The quality grades apply to new pneumatic tires for use on passenger cars. However, they do not apply to deep tread, winter type snow tires, space-saver or temporary use spare tires, tires with nominal rim diame- ters of 12 inches or less, or to some limited production tires.
DOT quality grades – All passenger car tires must confirm to Federal Safety Requirements in addition to these grades.
J Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified govern- ment test course. For example, a tire graded 150 would wear one and one-half (1-1/2) times as well on the government course as a tire graded 100. The rela- tive performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to varia- tions in driving habits, service practices and differences in road charac- teristics and climate.
J Traction AA, A, B, C The traction grades, from highest to lowest, are AA, A, B and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of as-
13-2
FORESTER (NA) A8050BE–A (ENG.)
Consumer information and Reporting safety defects
phalt and concrete. A tire marked C may have poor traction perfor- mance.
WARNING
The traction grade assigned to this tire is based on straightahead braking traction tests, and does not include acceleration, corner- ing, hydroplaning, or peak traction characteristics.
J Temperature A, B, C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of perfor- mance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher lev- els of performance on the laboratory test wheel than the minimum re- quired by law.
WARNING
The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive loading, either separately or in combina- tion, can cause heat buildup and possible tire failure.
13
– CONTINUED –
13-3
FORESTER (NA) A8050BE–A (ENG.)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABS (Anti-lock Brake System) ABS warning light (for vehicles with ABS) Accessory power socket Air cleaner element Air conditioner operation Air filtration system (if equipped) Aluminum wheels (If equipped) Antenna system Ashtray AT OIL TEMPerature warning light (for AT vehicles) Audio set Automatic/Emergency Locking Retractor (A/ELR) Automatic transmission Automatic transmission fluid
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Brake booster Brake fluid Brake pedal Brake system Brake system warning light Braking Braking tips Bulb chart
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacities Cargo anchorage eyelets Cargo area light Catalytic converter CD player (if equipped) Center console Charge warning light CHECK ENGINE warning light/Malfunction indicator lamp
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . .
14-2
7-23
3-13
6-8
11-18
4-10
4-12
11-49
5-2
6-13
3-13
5-3
1-12
7-14
11-2211-31
11-31
11-28
11-37
7-22
3-14
7-22
7-22
12-712-3
6-18
6-16
8-4
5-42
6-3
3-12
3-11FORESTER (NA) A8050BE–A (ENG.)
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child restraint systems Child safety locks Cigarette lighter (if equipped) Cleaning aluminum wheels Cleaning fog light lens Cleaning the interior Clock Clutch fluid Clutch pedal (Manual transmission vehicles) Coat hook Coin tray Cooling system Corrosion protection Cruise control (if equipped) Cup holder
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-25
2-19
6-11
10-3
10-4
10-6
6-8
11-30
11-38
6-14
6-5
11-14
8-15, 10-4
7-28
6-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
Dashboard storage compartment (if equipped) Dimensions Disc brake pad wear warning indicators Door locks Door open warning lights Door storage compartment Drive belts Driving in foreign countries Driving tips for AWD vehicles
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical system Emergency Locking Retractor (ELR) Engine Engine compartment overview Engine coolant Engine exhaust gas (Carbon monoxide) Engine hood Engine oil
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4
12-2
7-23
2-3
3-15
6-5
11-20
8-5
8-612-2
1-11
12-2
11-8
11-15
8-3
11-6
11-914-3
14
FORESTER (NA) A8050BE–A (ENG.)
Engine overheating Exterior care
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastening the seatbelt Flat tires Fog light (if equipped) Fog light switch (if equipped) Front differential gear oil
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Automatic transmission vehicles)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seats Front turn signal, parking light and front side marker light Front-wheel drive warning light (for AT vehicles) Fuel Fuel economy hints Fuel filler lid and cap Fuel gauge Fuel requirements Fuse panel located behind the coin tray Fuse panel located in the engine compartment Fuses Fuses and circuits
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
Gauges Glove compartment GVWR and GAWR (Gross Vehicle Weight Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
and Gross Axle Weight Rating)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-10
10-21-13
9-2
11-56
3-2011-24
1-2
11-57
3-15
7-2
8-2
7-4
3-8
7-2
12-4
12-6
11-49
12-43-6
6-38-17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hazard warning flasher Headlight Heater operation Heating and air conditioning control system High beam indicator High mount stop light
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5, 9-2
11-55
4-6
4-4
3-15
11-6114-4
FORESTER (NA) A8050BE–A (ENG.)
Horn
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index
3-28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch Illumination brightness control In-dash 6 CD auto changer 1 (if equipped) Inside mirror Installation of accessories Interior light
