Login- Download PDF Manual
-
Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle. Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-105.
5-105
Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get approved cleaning products from your dealer/retailer. See Vehicle Care/Appearance Materials on page 5-109. If your vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible.
5-106
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts.
Windshield, Backglass, and Wiper Blades Clean the outside of the windshield and backglass with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. Wash the windshield thoroughly when you clean the blades. Bugs, road grime, sap and a buildup of vehicle wash/wax treatments may cause wiper streaking. Replace the wiper blades if they are worn or damaged. Wipers can be damaged by: (cid:127) Extreme dusty conditions (cid:127) Sand and salt (cid:127) Heat and sun (cid:127) Snow and ice, without proper removal
If you use strong soaps, chemicals,
Aluminum Wheels Notice: Chrome wheels and other chrome trim may be damaged if you do not wash your vehicle after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust. Always wash your vehicle’s chrome with soap and water after exposure. Notice: abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, you could damage the surface of the wheel(s). The repairs would not be covered by your warranty. Use only approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only.
The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged. Do not use chrome polish on aluminum wheels. Notice: automatic car wash that has silicone carbide tire cleaning brushes, you could damage the aluminum or chrome-plated wheels. The repairs would not be covered by your warranty. Never drive a vehicle equipped with aluminum or chrome-plated wheels through an automatic car wash that uses silicone carbide tire cleaning brushes.
If you drive your vehicle through an
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
5-107
At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer/retailer or an underbody car washing system can do this for you.
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on the vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, Saab will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.
Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer/retailer. Larger areas of finish damage can be corrected in your dealer’s/retailer’s body and paint shop.
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection.
5-108
Vehicle Care/Appearance Materials
Description
Usage
Description
Usage
Swirl Remover Polish
Polishing Cloth Wax-Treated
Tar and Road Oil Remover
Interior and exterior polishing cloth.
Removes tar, road oil, and asphalt.
Chrome Cleaner and Polish
Use on chrome or stainless steel.
White Sidewall Tire Cleaner
Removes soil and black marks from whitewalls.
Vinyl Cleaner
Cleans vinyl.
Glass Cleaner
Chrome and Wire Wheel Cleaner
Finish Enhancer
Removes dirt, grime, smoke and fingerprints.
Removes dirt and grime from chrome wheels and wire wheel covers.
Removes dust, fingerprints, and surface contaminants. Spray on and wipe off.
Cleaner Wax
Foaming Tire Shine Low Gloss
Wash Wax Concentrate
Spot Lifter
Odor Eliminator
Removes swirl marks, fine scratches, and other light surface contamination.
Removes light scratches and protects finish.
Cleans, shines, and protects in one step. No wiping necessary.
Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free.
Quickly removes spots and stains from carpets, vinyl, and cloth upholstery.
Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.
5-109
Vehicle Identification
Vehicle Identification Number (VIN)
This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Certification/Tire and Service Parts labels and the certificates of title and registration.
Engine Identification The eighth character in your VIN is the engine code. This code helps you identify your vehicle’s engine, specifications, and replacement parts. See Capacities and Specifications on page 5-122 for your vehicle’s engine code.
Service Parts Identification Label This label is on the inside of the glove box. It is very helpful if you ever need to order parts. The label has the following information: (cid:127) Vehicle Identification Number (VIN) (cid:127) Model designation (cid:127) Paint information (cid:127) Production options and special equipment Do not remove this label from the vehicle.
5-110
Electrical System
Add-On Electrical Equipment Notice: Do not add anything electrical to your vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage your vehicle and the damage would not be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Add-on equipment can drain your vehicle’s battery, even if your vehicle is not operating. Your vehicle has an airbag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-66.
Headlamps The headlamp wiring is protected by fuses, one for each headlamp, in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have your headlamp wiring checked right away.
Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed.
5-111
Power Windows and Other Power Options Circuit breakers in the fuse block protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed or goes away.
Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.
If you ever have a problem on the road and don’t have a spare fuse, you can borrow one that has the same amperage. Just pick some feature of your vehicle that you can get along without — like the radio or cigarette lighter — and use its fuse, if it is the correct amperage. Replace it as soon as you can.
Engine Compartment Fuse Block The engine compartment fuse block is located in the engine compartment, on the passenger side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. Notice: Spilling liquid on any electrical components on your vehicle may damage it. Always keep the covers on any electrical component.
5-112
4.2L L6 Engine
Fuses
Usage
Electronically Controlled Air Suspension
Passenger Side Headlamp High-Beam
Fuses
Usage
Passenger Side Headlamp Low-Beam
Trailer Back-Up
5-113
Fuses
Usage
Fuses
Usage
10
11
12
13
15
16
18
19
20
21
22
23
Driver Side Headlamp High-Beam
Driver Side Headlamp Low-Beam
Windshield Wiper
Automatic Transfer Case
Windshield Washer
Powertrain Control Module B
Fog Lamps
Stoplamp
Cigarette Lighter
Electric Adjustable Pedals
Ignition B
Airbag System
Electric Brake
Cooling Fan
Horn
Ignition E
Electronic Throttle Control
5-114
24
25
26
27
28
29
30
31
50
51
52
53
54
57
59
Instrument Panel Cluster/Driver Information Center (DIC)
Brake Transmission Shift Interlock
Transmission Control Module (TCM) Canister
Backup
Powertrain Control Module 1
Oxygen Sensor
Air Conditioning
Truck Body Controller 1
Passenger Side Trailer Turn
Driver Side Trailer Turn
Hazard Flashers
Headlamp Driver Module
Air Injection Reactor Solenoid
Ignition A1
Regulated Voltage Control
J-Case Fuses
Usage
Relays
Usage
14
32
33
34
35
36
56
58
62
Trailer Stoplamp/Turn Signal
Trailer
Antilock Brake System
Ignition A
Driver Side Headlamp
Blower Motor
Air Pump
Passenger Side Headlamp
Vehicle Stability Enhancement System (StabiliTrak®)
Relays
Usage
37
38
39
40
41
Headlamp Washer
Rear Windshield Wiper/Washer
Fog Lamps
Horn
Fuel Pump
42
43
44
45
46
47
49
55
59
60
61
62
Windshield Washer
High-Beam Headlamp
Air Conditioning
Cooling Fan
Headlamp Driver Module
Starter
Electric Adjustable Pedals
Air Injection Reactor Solenoid
Low-Beam Headlamp
Ignition 1
Powertrain
Vehicle Stability Enhancement System (StabiliTrak®)
Misc.
48
Usage
Instrument Panel Battery
5-115
5.3L V8 and 6.0L V8 Engine
Fuses
Usage
Electrically Controlled Air Suspension
Passenger Side Headlamp High-Beam
5-116
Fuses
Usage
Passenger Side Headlamp Low-Beam
Trailer Back-Up
Fuses
Usage
Fuses
Usage
10
11
12
13
14
15
16
18
19
Driver Side Headlamp High-Beam
Driver Side Headlamp Low-Beam
Windshield Wiper
Automatic Transfer Case
Windshield Washer
Powertrain Control Module B
Fog Lamps
Stoplamp
Cigarette Lighter
Ignition Coils
Transmission Control Module/Canister
Ignition B
Airbag System
Electric Brake
20
21
22
23
24
25
26
27
28
29
30
31
50
51
Cooling Fan
Horn
Ignition E
Electronic Throttle Control
Instrument Panel Cluster/Driver Information Center
Brake Transmission Shift Interlock
Engine 1
Backup
Engine Control Module 1
Engine Control Module
Air Conditioning
Injector Bank A
Passenger Side Trailer Turn
Driver Side Trailer Turn
5-117
Fuses
Usage
J-Case Fuses
Usage
52
53
54
55
56
57
58
59
61
66
Hazard Flashers
Transmission
Oxygen Sensor B
Oxygen Sensor A
Injector Bank B
Headlamp Driver Module
Truck Body Controller 1
Electric Adjustable Pedals
Ignition A1
Regulated Voltage Control
J-Case Fuses
Usage
17
32
33
Trailer Turn Signal, Stoplamps
Trailer
Antilock Brake System
5-118
34
35
36
62
65
Ignition A
Blower Motor
Driver Side Headlamp
Passenger Side Headlamp
Vehicle Stability Enhancement System (StabiliTrak®)
Relays
Usage
37
38
39
40
41
42
43
Headlamp Washer
Rear Wiper
Fog Lamps
Horn
Fuel Pump
Windshield Washer
High-Beam Headlamp
Rear Underseat Fuse Block The rear underseat fuse block is located on the driver side of the vehicle, under the second row seat. Pull the seat cushion forward to access the fuse block.
Relays
Usage
44
45
46
47
49
60
63
64
Air Conditioning
Cooling Fan
Headlamp Driver Module
Starter
Electric Adjustable Pedals
Powertrain
Low-Beam Headlamp
Ignition 1
Misc.
48
Usage
Instrument Panel Battery
5-119
Fuses
Usage
01
02
03
04
05
06
07
08
09
10
11
12
13
14
1516
17
18
19Passenger Door Control Module Driver Door Control Module Liftgate Module 2
Truck Body Controller 3
Blank Blank Truck Body Controller 2
Power Seats Rear Wiper Driver Door Module Amplifier Passenger Door Module Blank Driver Side Rear Parking Lamps Blank Vehicle Center High-Mounted Stoplamp (CHMSL) Passenger Side Rear Parking Lamps Locks Liftgate Module/Driver Seat Module5-120
Fuses
Usage
Fuses
20
21
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37Blank Locks Blank Unlock Ignition 0
Overhead Battery/OnStar® System Rainsense™ Wipers Sunroof Accessory Parking Lamps Truck Body Controller Accessory Truck Body Controller 5
Front Wipers Ignition 3
Vehicle Stop Transmission Control Module Heat Ventilation Air Conditioning B38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53Usage Front Parking Lamps Rear Left Turn Signal Heat, Ventilation, Air Conditioning 1
Front Right Turn Signal Radio Trailer Park Rear Right Turn Signal Blank Auxiliary Power 1
Blank Ignition 0
Not Used Blank Front Left Turn Signal Brakes Truck Body Controller 45-121
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information.
Application
Capacities
English
Metric
Air Conditioning Refrigerant R134a
Cooling System
4.2L L6 Engine
5.3L V8 Engine
6.0L V8 Engine
Engine Oil with Filter
4.2L L6 Engine
5.3L V8 Engine
6.0L V8 Engine
5-122
For the air conditioning system refrigerant charge amount, see the refrigerant caution
label located under the hood. See your dealer
for more information.
9.7 qt
11.2 qt
11.2 qt
7.0 qt
6.0 qt
6.0 qt
9.2 L
10.6 L
10.6 L
6.6 L
5.7 L
5.7 L
Application
Fuel Tank
AWD Transfer Case Lubricant
Transmission (Drain and Refill)
Capacities
English
22.0 gal
2.0 qt
5.0 qt
Metric
83.3 L
1.8 L
4.7 L
Wheel Nut Torque
140 Y All capacities are approximate. When adding, be sure to fill to the appropriate level, as recommended in this manual. Recheck the fluid level after filling.
100 lb ft
Engine Specifications
Engine
VIN Code
Transmission
Spark Plug Gap
VORTEC™ 4.2L L6
VORTEC™ 5.3L V8
6.0L V8
Automatic
Automatic
Automatic
0.040 inches (1.01 mm)
0.040 inches (1.01 mm)
0.040 inches (1.01 mm)
5-123
✍ NOTES
5-124
Section 6
Maintenance Schedule
Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
Using the Maintenance Schedule ......................6-2
Scheduled Maintenance ...................................6-3
Additional Required Services ............................6-6
Maintenance Footnotes ...................................6-7Owner Checks and Services ............................6-8
At Each Fuel Fill ............................................6-9
At Least Once a Month ...................................6-9
At Least Once a Year ...................................6-10
Recommended Fluids and Lubricants ...............6-12
Maintenance Replacement Parts .....................6-14
Engine Drive Belt Routing ..............................6-15
Maintenance Record .....................................6-166-1
Maintenance Schedule
Introduction Important: Keep engine oil at the proper level and change as recommended.
Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance might not be covered by warranty.
Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.
6-2
Using the Maintenance Schedule We want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather. You might use your vehicle in making deliveries. Or you might drive it to work, to do errands, or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You might need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your dealer/retailer. This schedule is for vehicles that:
carry passengers and cargo within recommended limits. You will find these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 4-22. are driven on reasonable road surfaces within legal driving limits. use the recommended fuel. See Gasoline Octane on page 5-5.
(cid:127) (cid:127) (cid:127) The services in Scheduled Maintenance on page 6-3
should be performed when indicated. See Additional Required Services on page 6-6 and Maintenance Footnotes on page 6-7 for further information.{CAUTION:
Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your dealer/retailer to have a qualified technician do the work. See Doing Your Own Service Work on page 5-4.
Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your dealer/ retailer do these jobs. When you go to your dealer/retailer for your service needs, you will know that trained and supported service technicians will perform the work using genuine parts.
Owner Checks and Services on page 6-8 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-14. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine parts from your dealer/retailer.
Scheduled Maintenance When the CHANGE ENGINE OIL DIC message comes on, it means that service is required for your vehicle. See DIC Warnings and Messages on page 3-48. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. Your dealer/retailer has trained service technicians who will perform this work using genuine parts and reset the system.
6-3
If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil Life System on page 5-22 for information on the Engine Oil Life System and resetting the system. When the CHANGE ENGINE OIL DIC message appears, certain services, checks, and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II,
and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I — Use Maintenance I if the message comes on within 10 months since the vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the message comes on 10 months or more since the last service or if the message has not come on at all for one year.
Scheduled Maintenance
Service
Maintenance I Maintenance II
Change engine oil and filter. See Engine Oil on page 5-18. Reset oil life system. See Engine Oil Life System on page 5-22. An Emission Control Service.
Visually check for any leaks or damage. See footnote (j).
Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 5-24. See footnote (k).
Rotate tires and check inflation pressures and wear. See Tire Inspection and Rotation on page 5-75 and “Tire Wear Inspection” in At Least Once a Month on page 6-9.
•
•
•
•
•
•
•
6-4
Scheduled Maintenance (cont’d) Service
Maintenance I Maintenance II
Inspect brake system. See footnote (a).
Check engine coolant and windshield washer fluid levels and add fluid as needed.
Perform any needed additional services. See “Additional Required Services” in this section.
Inspect suspension and steering components. See footnote (b).
•
•
•
Inspect engine cooling system. See footnote (c).
Inspect wiper blades. See footnote (d).
Inspect restraint system components. See footnote (e).
Lubricate body components. See footnote (f).
Check transmission fluid level and add fluid as needed. See footnote (g).
•
•
•
• • • • • •
6-5
Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.
Service and Miles (Kilometers)
Additional Required Services 75,000
25,000
(40 000)50,000
(80 000)(120 000)
•
•
•
•
•
•
•
•
•
Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-24. Change automatic transmission fluid and filter (severe service). See footnotes (g) and (h). Change automatic transmission fluid and filter (normal service). See footnote (g). Automatic transfer case only: Change transfer case fluid. See footnote (g). Replace spark plugs. An Emission Control Service. V8 engine only: Inspect spark plug wires. An Emission Control Service.
6-6
100,000
(160 000)125,000
(200 000)150,000
(240 000)•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Additional Required Services (cont’d)
Service and Miles (Kilometers)
Engine cooling system service (or every five years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. See footnote (l).
25,000
(40 000)50,000
(80 000)75,000
(120 000)
100,000
(160 000)125,000
(200 000)150,000
(240 000)•
•
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. (c) Visually inspect hoses and have them replaced if they are cracked, swollen, or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine parts as needed. To help ensure proper operation, a pressure test
of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year. (d) Inspect wiper blades for wear, cracking, or contamination. Clean the windshield and wiper blades, if contaminated. Replace wiper blades that are worn or damaged. See Windshield Wiper Blade Replacement on page 5-57 and Windshield, Backglass, and Wiper Blades on page 5-106 for more information. (e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also see Checking the Restraint Systems on page 1-68.
6-7
(f) Lubricate all key lock cylinders, hood latch assembly, secondary latch, pivots, spring anchor, release pawl, rear compartment hinges, outer liftgate handle pivot points, rear door detent link, roller mechanism, liftgate handle pivot points, latch bolt, fuel door hinge, cargo door hinge, locks, and folding seat hardware. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better, and not stick or squeak. (g) Inspect hoses for cracks, chafing, leaks, kinks, and proper installation. (h) Change automatic transmission fluid and filter if the vehicle is mainly driven under one or more of these conditions:
− In heavy city traffic where the outside temperature
regularly reaches 90°F (32°C) or higher.
− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police,
or delivery service.
(i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 5-28
for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck. Pressure test the cooling system and pressure cap. (j) A fluid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the fluid level checked. Add fluid if needed. (k) If you drive regularly under dusty conditions, inspect the filter at each engine oil change. (l) Visually inspect belt for fraying, excessive cracks, or obvious damage. Replace belt if necessary.Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability, and emission control performance of your vehicle. Your dealer/retailer can assist you with these checks and services. Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12.
6-8
It is important to check the engine oil
At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Notice: regularly and keep it at the proper level. Failure to keep the engine oil at the proper level can cause damage to the engine not covered by your warranty. Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-18. Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 5-28. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer fluid reservoir and add the proper fluid if necessary.
At Least Once a Month Tire Inflation Check Inspect your vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Inflation - Tire Pressure on page 5-67. Check to make sure the spare tire is stored securely. See Changing a Flat Tire on page 5-86. Tire Wear Inspection Tire rotation may be required for high mileage highway drivers prior to the Engine Oil Life System service notification. Check the tires for wear and, if necessary, rotate the tires. See Tire Inspection and Rotation on page 5-75.
6-9
At Least Once a Year Starter Switch Check
{CAUTION:
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before you start, be sure you have enough room
around the vehicle.
2. Firmly apply both the parking brake and the regular
brake. See Parking Brake on page 2-28. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.
3. Try to start the engine in each gear. The vehicle should start only in PARK (P) or NEUTRAL (N). If the vehicle starts in any other position, contact your dealer/retailer for service.
Automatic Transmission Shift Lock Control System Check
{CAUTION:
When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.
1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
2. Firmly apply the parking brake. See Parking Brake
on page 2-28. Be ready to apply the regular brake immediately if the vehicle begins to move.
3. With the engine off, turn the ignition to ON/RUN, but do not start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), contact your dealer/retailer for service.
6-10
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position.
The ignition should turn to LOCK/OFF only when the shift lever is in PARK (P). The ignition key should come out only in LOCK/OFF.
Contact your dealer/retailer if service is required. Parking Brake and Automatic Transmission Park (P) Mechanism Check
{CAUTION:
When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake.
To check the parking brake’s holding ability: With the engine running and the transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only. To check the PARK (P) mechanism’s holding ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.
Contact your dealer/retailer if service is required. Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.
6-11
(cid:127) (cid:127) (cid:127) (cid:127) Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer.
Usage
Fluid/Lubricant
Engine Oil
(Except 6.0L V8
Engine)Engine Oil (6.0L V8
Engine Only)
Engine oil which meets Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-18. The engine requires a special engine oil meeting Standard GM4718M. Oils meeting this standard can be identified as synthetic, and should also be identified with the American Petroleum Institute (API) Certified for Gasoline Engines starburst symbol. However, not all synthetic API oils with the starburst symbol will meet this standard. Look for and use only an oil that meets Standard GM4718M. For the proper viscosity, see Engine Oil on page 5-18.
6-12
Usage
Fluid/Lubricant
Engine Coolant
Hydraulic Brake
System
Windshield
Washer
Parking Brake Cable Guides
Power Steering
System
Automatic
Transmission
Key Lock Cylinders
Chassis
Lubrication
Front Axle
50/50 mixture of clean, drinkable water and use only DEX-COOL® Coolant. See Engine Coolant on page 5-28. Delco® Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.
Windshield Washer Solvent.
Chassis Lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Power Steering Fluid (Part No. U.S. 89021184, in Canada 89021186). DEXRON®-VI Automatic Transmission Fluid. Multi-Purpose Lubricant, Superlube (Part No. U.S. 12346241, in Canada 10953474). Chassis Lubricant meeting requirements of NLGI #2, Category LB or GC-LB. SAE 75W-90 Synthetic Axle Lubricant (Part No. U.S. 89021677, in Canada 89021678) meeting specifications.
Usage
Fluid/Lubricant
Usage
Fluid/Lubricant
Rear Axle
Transfer Case
Hood Latch Assembly, Secondary
Latch, Pivots, Spring Anchor, and Release
Pawl
SAE 75W-90 Synthetic Axle Lubricant (Part No. U.S. 89021677, in Canada 89021678) meeting specifications. With a complete drain and refill add 4 ounces (118 ml) of Limited-Slip Axle Lubricant Additive (Part No. U.S. 1052358, in Canada 992694) where required. See Rear Axle on page 5-50. AUTO-TRAK II Fluid (Part No. U.S. 12378508, in Canada 10953626).
Lubriplate Lubricant Aerosol meeting requirements of NLGI #2, Category LB or GC-LB.
Hood and Door Hinges, Body Door Hinge Pins, Liftgate
Hinge and Linkage,
Folding Seats,
and Fuel
Door Hinge
Multi-Purpose Lubricant, Superlube (Part No. U.S. 12346241, in Canada 10953474).
Outer Tailgate Handle Pivot Points and
Hinges
Weatherstrip Conditioning
Weatherstrip
Squeaks
Multi-Purpose Lubricant, Superlube (Part No. U.S. 12346241, in Canada 10953474).
Weatherstrip Lubricant (Part No. U.S. 3634770, in Canada 10953518) or Dielectric Silicone Grease (Part No. U.S. 12345579, in Canada 992887). Synthetic Grease with Teflon, Superlube (Part No. U.S. 12371287, in Canada 10953437).
6-13
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer.
Part
Part Number
ACDelco® Part Number
Automatic Transmission Filter Kit
Engine Air Cleaner/Filter
Engine Oil Filter
4.2L L6
5.3L V8; 6.0L V8
Spark Plugs
4.2L L6
5.3L V8; 6.0L V8
Wiper Blades
Front – 22 inches (56 cm)
Rear – 13 inches (33 cm)
6-14
24208576
15036141
89017342
89017524
12598004
12571164
15214346
15232655
TF337
A2014C
PF61
PF48
41-103
41-985
—
—
Engine Drive Belt Routing
4.2L V6 Engine
5.3L V8 and 6.0L V8 Engines
6-15
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record
6-16
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record (cont’d)
6-17
Date
Odometer Reading
Serviced By
Maintenance I or Maintenance II
Services Performed
Maintenance Record (cont’d)
6-18
Section 7
Customer Assistance Information
Customer Assistance and Information ...............7-2
Customer Satisfaction Procedure ......................7-2
Online Owner Center ......................................7-3
Customer Assistance for TextTelephone (TTY) Users ................................7-4
Customer Assistance Offices ............................7-4
Roadside Assistance Program ..........................7-4
Scheduling Service Appointments .....................7-7
Courtesy Transportation ...................................7-7
Collision Damage Repair .................................7-9Reporting Safety Defects ................................7-12
Reporting Safety Defects to the
United States Government ..........................7-12
Reporting Safety Defects to the
Canadian Government ................................7-12
Reporting Safety Defects to Saab ...................7-12
Service Publications Ordering Information .........7-13
Vehicle Data Recording and Privacy ................7-14
Event Data Recorders ...................................7-14
OnStar® ......................................................7-15
Navigation System ........................................7-15
Radio Frequency Identification (RFID) ..............7-157-1
Customer Assistance and Information
Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Saab. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur. If your concern has not been resolved to your satisfaction, the following steps should be taken:
STEP ONE: Discuss your concern with a member of dealership management. Normally, concerns can be quickly resolved at that level. If the matter has already been reviewed with the sales, service or parts manager, contact the owner of the dealership or the general manager.
STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the Saab Customer Assistance Center, in the U.S., by calling 1-800-955-9007. In Canada, contact Saab Customer Assistance Centre by calling 1-800-263-1999
(English and French).7-2
We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have the following information available to give the Customer Assistance Representative: (cid:127) Your name, address and daytime phone number. (cid:127) Vehicle Identification Number (VIN). This is available from the vehicle registration or title, or the plate at the top left of the instrument panel and visible through the windshield. The name of the selling dealership and location.
(cid:127) Vehicle delivery date and present mileage
(kilometers).
(cid:127) Nature and details of the problem you are
experiencing.
When contacting Saab, please remember that your concern will likely be resolved at a dealer’s facility. That is why we suggest you follow Step One first if you have a concern. If after contacting the Saab Customer Assistance Center your concern has not been resolved, please refer to the “Dispute Resolution Process” found in your Saab Consumer’s Guide.
(cid:127) Online Owner Center (United States only) The Owner Center is a resource for your Saab ownership needs. Specific vehicle information can be found in one place. The Online Owner Center allows you to: (cid:127) Get e-mail service reminders. (cid:127) Access information about your specific vehicle,
including tips and videos and an electronic version of this owner manual.
(cid:127) Keep track of your vehicle’s service history and
maintenance schedule. Find Saab dealers for service nationwide.
(cid:127) Receive special promotions and privileges only
available to members.
Refer to www.saabusa.com on the web for updated information and to register your vehicle.
My GM Canada (Canada only) My GM Canada is a password-protected section of gmcanada.com where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease. Here are a few of the valuable tools and services you will have access to:
− My Showroom: Find and save information on
vehicles and current offers in your area.
− My Dealers/Retailers: Save details such as address and phone number for each of your preferred GM Dealers or Retailers.
− My Driveway: Receive service reminders and
helpful advice on owning and maintaining your vehicle.
− My Preferences: Manage your profile, subscribe to
E-News and use tools and forms with greater ease.
To sign up to My GM Canada, visit the My GM Canada section within www.gmcanada.com.
7-3
(cid:127) Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Saab has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Saab by dialing: 1-866-612-0380. (TTY users in Canada can dial 1-800-263-3830.)
Customer Assistance Offices Saab encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Saab, refer to the addresses below. United States — Customer Assistance
Saab Customer Assistance Center Saab Cars USA, Inc. 4405-A International Boulevard Norcross, GA 30093
www.Saab.com 1-800-955-9007
1-866-612-0380 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-852-9001Canada — Customer Assistance
General Motors of Canada, Limited Customer Assistance Centre, CA1-163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7
www.gmcanada.com 1-800-263-1999 (English and French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800Roadside Assistance Program For vehicles purchased in the U.S., call 1-800-852–9001. For vehicles purchased in Canada, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year. As the owner of a new Saab vehicle, you are automatically enrolled in the Saab Roadside Assistance program. Who is Covered? Roadside Assistance coverage is for the vehicle operator, regardless of ownership. In Canada, a person driving this vehicle without the consent of the owner is not eligible for coverage.
7-4
Services Provided The following services are provided in the U.S. and Canada up to 5 years/100,000 miles (160 000 km), whichever occurs first, and in Canada only, up to a maximum coverage of $100. These services are provided at a nominal charge if the vehicle is no longer within the Powertrain warranty.
Fuel Delivery: Delivery of enough fuel for the vehicle to get to the nearest service station (approximately $5 Canada). In Canada, service to provide diesel may be restricted. For safety reasons, propane and other alternative fuels will not be provided through this service. Lock-out Service: Lock-out service will be covered at no charge if you are unable to gain entry into your vehicle. A remote unlock may be available if you have an active OnStar® subscription. To ensure security, the driver must present personal identification before lock-out service is provided. In Canada, the vehicle registration is also required. (cid:127) Emergency Tow From a Public Roadway or
Highway: Tow to the nearest dealership for warranty service or in the event of a vehicle-disabling crash. Winch-out assistance is provided when the vehicle is mired in sand, mud, or snow.
Flat Tire Change: Installation of a spare tire in good condition, when equipped and properly inflated, is covered at no charge. The customer is responsible for the repair or replacement of the tire if not covered by a warrantable failure. Jump Start: A battery jump start will be covered at no charge if the vehicle does not start. Trip Interruption Benefits and Assistance: In the event of a warranty related vehicle disablement, while en route and over 100 miles, for U.S. customers, and 250 kilometres, for Canadian customers, from the original point of departure, you may qualify for trip interruption expense assistance. This assistance covers reasonable reimbursement of up to a maximum of $1000 for U.S. customers, and $500 for Canadian customers, to assist you with some of the unplanned expense incurred within three days of the disablement you may incur while waiting for your vehicle to be repaired. Original detailed receipts and a copy of the repair order are required. In Canada, pre-authorization is also required. Trip Routing Service: Upon request, Roadside Assistance will send you detailed, computer personalized maps, highlighting your choice of either the most direct route or the most scenic route to your destination, anywhere in North America, along with helpful travel information pertaining to your trip.
7-5
(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) Please allow three weeks before your planned departure date. In Canada, trip routing requests will be limited to six per calendar year. Alternative Service (Canada only) There may be times when Roadside Assistance cannot provide timely assistance. Your advisor may authorize you to secure local emergency road service, and you will be reimbursed up to $100 upon submission of the original receipt to Roadside Assistance.
In many instances, mechanical failures may be covered. However, any cost for parts and labor not covered by warranty are the responsibility of the vehicle owner or driver. Saab and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims become excessive in frequency or type of occurrence.
Calling For Assistance For prompt and efficient assistance when calling, please provide the following to the Roadside Assistance Representative: (cid:127) Your name, home address, and home telephone
number Telephone number of your location Location of the vehicle
(cid:127) Model, year, color, and license plate number of the
vehicle
(cid:127) Odometer reading, Vehicle Identification Number
(VIN), and delivery date of the vehicle
(cid:127) Description of the problem
7-6
(cid:127) (cid:127) Towing and Road Service Exclusions Specifically excluded from Roadside Assistance coverage are towing or services for vehicles operated on a non-public roadway or highway, fines, impound towing caused by a violation of local, Municipal, State, Provincial, or Federal law, and mounting, dismounting or changing of snow tires, chains, or other traction devices. Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Saab and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification.
