2000 Saab 9 3 Owners Manual

Interior equipment, trunk

115

Manually adjusted front seat, Coupé and Convertible versions 1 Release lever, tipping backrest forward 2 Activation of the ”Easy Entry” feature when

the backrest is tipped forward

Activate ”Easy Entry” as follows: 1 Raise the release lever and hold it in its uppermost position until the backrest is tipped forward.

2 Slide the seat forward. The whole seat is

now shifted to its forward position.

Resetting: 1 Slide the seat back to the desired

position.

2 Fold the backrest to the upright position. Lock the front to rear seat adjustment. After resetting you should ensure that the backrest and seat are properly secured.

WARNING

(cid:127) Always check that the catch engages properly after the backrest is raised.

(cid:127) Check also that the seat’s lateral

adjuster is properly secured by trying to shift the seat. Both the backrest and the whole seat must be locked in place; otherwise you are at risk of injury during braking or in a collision.

116

Interior equipment, trunk

Electrically adjustable front seats (certain variants) Both seats can be operated from outside when one of the front doors is opened, to improve access to the car. For safety reasons, if the door is closed, the seat can only be adjusted when the ignition is ON. Note, that both front seats can be adjusted up to 30 seconds after the door has been closed.

WARNING

The seats are actuated by powerful motors. Bear this in mind when adjusting the seat, and make sure that nothing gets caught and damaged. Bear in mind that children can be injured if they play with the electrically-operated seats.

Height Raise the seat by lifting the front switch bar straight up. Lower the seat by pushing the front switch bar down. The same switch bar can be used to adjust the height of the front and rear edges of the seat independently by moving half of the switch in the direction desired.

Legroom adjustment For power seats, slide the switch bar for- ward or rearward to the desired position.

Memory function (certain variants) In some variants the electrically adjustable driver’s seat has a memory function. Three different settings can be programmed. 1 Make the desired adjustments to the

seat setting.

2 Store the setting of the seat by keeping the ”M” depressed and at the same time pressing one of the memory buttons, 1, 2 or 3. The SID will acknowledge stor- age with a chime.

When you next wish to activate the memory function, keep the desired memory button depressed while the seat adopts the pro- grammed settings. To change any of the three programmed settings, repeat stages 1 and 2.

Interior equipment, trunk

117

Backrest rake angle Push the rear lever forward or rearward to adjust the rake angle of the backrest.

118

Interior equipment, trunk

Electrically heated front seats (option on some model vari- ants/markets) Both front seats incorporate heating for the seat cushion and backrest. It is switched on and off using the buttons on the instrument panel. The heating is thermostatically controlled. It comes on when the temperature of the seat cushion goes below 79°F (26°C) and turns off when it reaches 97°F (36°C). Shut off the heating once the seat is warm.

Electrically heated seat cushions in the rear seat (option on some model variants / markets) Electrically heated seat cushions for the two outer seats in the back are available as an option. The ON/OFF control button for the cushion heating is located on the back of the center console. The warming-up time varies with the tem- perature outside. You can also switch the heat off by means of the button. The button has an integral indicator that is illuminated when the heating is on.

Lever for steering-wheel adjustment

Steering-wheel adjustment The steering wheel can be positioned fore-and-aft by pulling the lever to the left. Set the steering wheel to the desired posi- tion and return the lever to the locked status.

WARNING

For safety reasons, you should adjust the steering wheel only while the car is sta- tionary.

Horn signal The horn is operated by pressing at the outer edges of the airbag module in the center of the steering wheel.

Electrical windows

WARNING

(cid:127) Bear in mind the pinch hazard when the side windows are being raised. Make sure that all passengers keep their heads, hands and fingers clear of the window openings before you begin raising the windows.

(cid:127) Always remove the ignition key when leaving the car to avoid the danger of injury arising from unattended children operating the windows.

The electric window motors are equipped with overload protection. If this protection should trip, wait several seconds before operating the electric windows again. To open Press the window symbol on the button. The switches for the front windows have a third position for automatic opening of the window. Press the switch down all the way to lower the window completely. To cancel automatic lowering of the win- dow, lift the switch briefly. To close Lift the symbol side of the button. The actuating motor will be switched off automatically when the window is fully closed or when the switch is released.

Interior equipment, trunk

119

1 Control, sunroof (soft top operation, Convertible) 2 Window switches, front 3 Control for disengaging the window switches at the rear

Child safety: rear windows (ON/OFF) The window switches on the rear doors can be rendered inoperative by the ON/OFF switch in the panel on the center console. When the switch is ON, the rear side win- dows can be operated by the switch on each rear door. When the switch is OFF, the rear side win- dows can only be operated from the panel on the center console.

Extra button for the rear window operator

120

Interior equipment, trunk

Sunroof (option) The sunroof is operated electrically using the ROOF control on the center console. The sunroof can be opened completely or partially. As soon as you release the control the sunroof stops. 1 If you wish to open the sunroof all the way from the closed position, proceed as follows: (cid:127) To open: slide the control rearwards. (cid:127) To close: slide the control forwards. 2 You also have the option of opening the rear edge of the sunroof from the closed position for the purpose of ventilation. (cid:127) To open: slide the control forwards. (cid:127) To close: slide the control rearwards.

But you must release the control after each position so as to shift between the two functions. The sunroof also has an inner sun blind that slides by hand.

WARNING

Be alert to danger of fingers being trapped when operating the sunroof. Always remove the ignition key when leaving the car, to avoid the danger of injury arising from unattended children operating the sunroof.

Emergency operation of the sunroof The sunroof can be operated manually with a screwdriver, e.g. in the case of an electri- cal fault. Slide back the cover on the roof console. Insert a screwdriver into the slot in the center of the motor shaft and turn Turn clockwise to open the sunroof. Turn counterclockwise if the sunroof is open at the rear edge.

Interior equipment, trunk

121

1 Interior lighting is off 2 Lighting comes on when a door is opened 3 Interior lighting on continuously

Interior lighting The interior lighting consists of one dome light in the front and one in the back. The switch for the interior lighting is on the over- head panel next to the rearview mirror. When the switch is in the mid-position (door-activated), the interior lighting will come on: (cid:127) When the car is unlocked from outside. (cid:127) When any door is opened with the ignition

off.

(cid:127) When the ignition key is withdrawn from

the switch.

Rear-seat lighting 1 Reading lights 2 Dome light

Trunk lighting The trunk lighting is switched on and off when you open and close the trunk, if the switching button is set to ON. The lighting can also be switched on and off using the button on the light.

The lighting goes out about 12 seconds after the doors are closed or when the igni- tion is turned on, provided that the switch is in the mid-position. If the doors are left open and the switch is in position 2 or 3 with the ignition off, the inte- rior lighting is turned off automatically after 20 minutes to preserve battery life. The sun visors are equipped with vanity mir- rors. On certain model variants, the sun visors are fitted with vanity lighting, which turns on when the cover is lifted. 9-3 Convertible: see page 52.

122

Interior equipment, trunk

Sun visor with vanity mirror

Cup holder There are two cupholders, one in the fascia under the SID unit and one in the cen- ter-console compartment between the front seats on certain models. Next to the cup holder between the front seats is a coin tray.

Cup holder in the center console

Interior equipment, trunk

123

Front ashtray

Rear ashtray

Ashtrays (accessory) The car is equipped with two ashtrays. One is positioned low down on the dash and the other on the back of the center console. Open the front ashtray by lightly pressing on the front. Remove it by depressing the catch on the underside. You do not need to open it in order to take it out. To replace it, just push it straight in.

Open the rear ashtray by lightly pulling its upper edge rearward. Remove it by depressing the catch and opening it past the catch point. To put it back, align it with the two locating pins on either side of the opening, then push it closed. The cigarette lighter socket can also be used as a power supply for a mobile phone or other electrical accessory.

WARNING

The maximum output that can be taken from the cigarette lighter socket is 240 W (20 A).

Glove compartment 1 To unlock 2 To lock

Glove compartment

WARNING

The glove compartment must be closed while travelling. An open glove-compart- ment door could cause leg injuries in the event of a collision.

There are additional storage pockets on the front edges of the front seats and on the passenger side of the center console.

124

Interior equipment, trunk

Rear-view mirror 1 Day position 2 Night position

Adjusting the door mirrors 1 Select mirror 2 Use touch pad to adjust mirror

Retracting a mirror

Rear-view mirrors The rear-view mirror has day/night positions that can be selected by means of a knob beneath the mirror. Adjust the mirror for best vision in the day position and pull the tab on the bottom of the mirror toward you for the night position.

Door mirrors The door mirrors are electrically adjustable. The controls are on the driver’s door. 1 Use the upper button to select a door

mirror.

2 Use the touch pad to set the mirror ver- tically and horizontally. There are raised points at the 12, 3, 6 and 9 o’clock posi- tions to indicate adjustment points.

If subjected to a certain force, the whole mirror will fold back to prevent injury.

The mirror can also be retracted by hand, which can be useful when parking in con- fined spaces, e.g. on car ferries. Don’t forget to fold the mirrors out again before driving away. The electric heating of the door mirrors is switched on and off with the same button as the heating of the rear window.

NOTE

The door mirrors should be retracted before the car is put through an automatic carwash.

Trunk, Coupé and 5-door

WARNING

When the back seat has been put back in place, make certain that the belt beam is locked firmly on both sides (the red warning tabs must go down). This is vital since the upper anchorages for the safety belts are located in the belt beam. The belts will not restrain a rear seat occupant if the belt beam is not properly latched. When the entire rear seat has been lowered, you must remove the rear window shelf. Otherwise it could come loose and cause per- sonal injury during a collision.

Trunk lid lock Unlock the trunk lid by pressing the lower button on the remote trans- mitter, by pressing the remote release button on the driver’s door or by using the key. The alarm horn sounds three times and the lights flash when the trunk is released with the remote control. Programming features, see page 231.

Interior equipment, trunk

125

Lowering the entire rear seat To lower the rear seat, the front seats must be moved forward if they are in the most rearward position. The seat back must be almost ver- tical. 1 Flip up the seat bottom by pulling the loops located between the

backrest cushions and seat cushions.

2 Rest the seat cushions on edge just behind the front seats. 3 Release the entire backrest cushion, including the belt beam, by pressing in the latch in the handle on the left (driver’s) side. After this has been done, the fact that the belt beam has been released is indicated by the red "warning tabs" popping up on the right and left sides of the beam. For increased load capacity with the backrest cushion down, remove the rear seat head restraints (5).

126

Interior equipment, trunk

4 Lower the entire backrest cushion by pulling this same handle (item 3) forward. At the same time, pivot the beam backwards. IMPORTANT: When you replace the belt beam using the handle (item 3), you must verify that it is properly locked and that the two red "warning tabs" go down (thereby indicating that locking has taken place properly).

5 To increase the volume, the rear head restraints can be removed

before the backrest cushion is lowered.

WARNING

Never leave a child or animal unattended in the car. During sunny weather the temperature in the cabin/luggage compartment can climb to 160-180°F (70-80°C). Small children are very susceptible to heat stroke.

Lowering the right-hand part of the rear seat

WARNING

(cid:127) If the head restraints have been removed, they must be stored safely so that they cannot be thrown about and injure someone while braking or in a collision.

(cid:127) Do not ride in the rear seat without having remounted the head restraints, and making sure they are properly locked in place.

(cid:127) Whenever you handle any system containing moving parts, such as the belt beam, always be careful not to get pinched. (cid:127) Never keep objects on the rear window shelf since they can be thrown forward and cause personal injury during heavy brak- ing or in the event of a collision.

(cid:127) When the back seat has been put back in place, make certain that the belt beam is locked firmly on both sides (the red warn- ing tabs must go down). This is vital since the upper anchor- ages for the safety belts are located in the belt beam. The belts will not restrain a rear seat occupant if the belt beam is not properly latched

To provide more flexibility, the rear seat is divided so that you can lower the narrower (right) part separately. 1 Tilt the seat cushion forward by pulling the loop located between

the backrest and the seat cushion.

2 Stand the seat cushion on end behind the front seats. 3 Release the right backrest cushion by means of the latch on the

belt beam’s right side just behind the head restraint.

4 Lower the right backrest cushion. IMPORTANT: When you replace the right backrest cushion, make certain that it is properly locked.

Warning tabs

Interior equipment, trunk

127

128

Interior equipment, trunk

Removing the parcel shelf 1 Open the trunk lid. 2 Unhook the rubber ties. 3 Lift the rear parcel shelf and pull it away from the guide pins in

the front edge of the shelf support.

Load opening (trunk pass through) A load opening is provided in the backrest so that you can carry long narrow objects. Switch off the engine and set the parking brake before loading or unloading long objects. Otherwise, there is risk that you will inadvert- ently bump the gear/selector lever and the car could start moving. 1 Lower the rear armrest. 2 Open the cover by lifting the locking handle.

Interior equipment, trunk

129

WARNING

WARNING

(cid:127) Never place any objects on top of the rear parcel shelf. In the event of a col- lision, unsecured cargo may present a safety hazard and cause personal injuries to vehicle occupants.

(cid:127) Do not obstruct outward vision or the ability to exit the vehicle when loading the vehicle.

(cid:127) When the rear seat backrest is placed upright after having been folded for- ward, ensure that all rear safety belts are accessible and properly routed.

(cid:127) Make sure that tire pressures are

properly adjusted in accordance with altered vehicle weight (refer to tire pressures in the Specifications sec- tion of this manual).

Load opening: Always secure a load properly. You can, for example, use the hip strap in the center rear safety belt. This will reduce the risk of having the load thrown about during a collision and causing personal injury. Trunk: Lay heavy suitcases flat on the floor. Then place smaller and lighter items of luggage on top. Always secure heavy, bulky loads to the four tie downs in the trunk. This will reduce risk of having them thrown about during heavy braking or during a collision and causing personal injury. When the backrest is lowered, narrow objects can also be thrown around and cause injury. You should thus secure them well. To retain the car’s safe normal handling characteristics, you must be careful not to exceed its maximum load capacity, (see page 220).

Tie downs Four tie downs for securing the load are fitted inside the trunk. Place the load as far in as possible. Trunk lighting To the left in the trunk is a light which goes on and off when the trunk lid is opened and closed. The lighting can also be turned on and off using the button on the light housing. If the trunk lid is left open, the lighting will go off after 20 minutes to prevent the battery from being drained.

130

Interior equipment, trunk

Tools and spare wheel The tool kit and compact spare wheel are kept beneath the carpeting in the trunk.

Rear spoiler, Saab 9-3 Viggen Coupé and 5-door

WARNING

Saab 9-3 Viggen Coupé and 5-door: Avoid placing your hands on the upper part of the rear fender when the tailgate is to be closed because of the risk of getting finger caught between the spoiler and the fender.

Interior equipment, trunk

131

Manually opening the fuel filler door Coupé and 5-door models If the fuel filler door (which is controlled by the central locking system) does not unlock, proceed as follows. Check fuse 20. If it is blown or its replace- ment blows, you can release the lock motor from the door as follows: 1 Use a sharp knife to release the pre-cut rectangle on the right in the upholstery in the trunk so that you can access the two retaining screws that secure the lock motor to the fuel filler door.

2 Unscrew the retaining screws some- what and back them out through the screw holes, whereupon the lock motor will be released from the door.

Manually opening the fuel filler door, Con- vertible, see page 52.

1 Cutout outline in the upholstery of the trunk 2 Undo the retaining screws of the lock motor 3 Remove the screws through the screw

holes

132

Interior equipment, trunk

Starting and driving

Ignition switch ................. 134 Starting the engine.......... 135 Important considerations for driving....................... 136 Engine Break-in Period... 140 Gear changing ................. 141 Manual transmission ...... 141 Automatic transmission . 141 Cruise Control ................. 148 Braking............................. 149 Parking ............................. 151 Economical motoring ..... 153

Starting and driving

133

Driving in cold weather ... 154 Driving in hot weather ..... 156 Towing a trailer ................ 156 Driving with a roof rack load.................................. 158 Towing the car.................. 160 Jump starting ................... 162 Driving considerations with compact spare wheel/tire fitted............... 165 For long trips.................... 165 Driving with the trunk lid open ................................ 166 Driving in deep water....... 166

134

Starting and driving

Ignition switch The single lock used for both the ignition and gear/selector lever is in the center con- sole located between the front seats. Before you can remove the key, the car must be in reverse gear (manual gearbox cars) or the Parking (P) position (cars with automatic transmission). The key for this lock also fits all other locks in the car. The key number is on a small plastic tag delivered together with the keys. Be sure to save this plastic tab since it has the key number on it.

LOCK position Put the gear lever in reverse and turn the ignition key to the LOCK posi- tion. For cars with automatic transmission, select the Parking (P) position and turn the ignition key to the LOCK position. The gear lever is now locked. The key can only be removed when the gear lever is in this position. The parking lights, the hazard warning lights and the interior lighting can still be illuminated.

OFF position Gear lever is not locked (manual transmission). Automatic transmission: gear lever is locked until brake pedal is depressed.

ON position The entire electrical system is operative. Do not leave the key in the ON position while the engine is not running. Turn the key to the LOCK position to disconnect the electrical system. When you turn the key to the ON position, the warnings and indicators in the main instrument light so that you can check to see that they are functioning properly. They are extinguished after approx. 3 seconds.

Start position (ST) The starter motor operates in this position. When you release the key, it springs back to the ON position. Restarting the starter motor is pre- vented. If starting is unsuccessful, you must turn the key back to a posi- tion between OFF and LOCK before you can turn it to the start (ST) position again.

WARNING

(cid:127) Always remove the key before leaving

the car.

(cid:127) Always apply the parking brake before

removing the ignition key.

NOTE

Take care not to spill drinks or to drop crumbs over the ignition switch. If dirt or liquid gets into it, the switch may not operate properly.

If the car does not start If the text "KEY NOT ACCEPTED" appears on the SID when the engine refuses to start, the trouble may be a fault in the transponder of the key or in the receiver of the ignition switch. Proceed as follows: • Turn the key back to the LOCK position. (cid:127) Turn the key to the ON position. (cid:127) Press one of the buttons on the remote

control (the LED on top of the dash stops flashing).

(cid:127) Start the engine. Try the other key. If it works, the trouble is in the first key. Call on an authorized Saab dealer for inspection and correction.

Starting the engine

WARNING

(cid:127) Carbon monoxide (CO) is a colorless, odorless, poisonous gas. Be alert to the danger of CO – always open the garage doors before starting the engine in the garage.

(cid:127) There is also a danger of CO poison- ing if the exhaust system is leaking.

Do not run the starter motor for more than 25 seconds at a time. Wait 20-30 seconds before running the starter again, to give the battery time to recover. Avoid racing the engine or putting a heavy load on it before it has warmed up. Let the engine idle for at least 10 seconds and then drive away as long as the engine oil warning light has gone out to enable the engine to attain its normal temperature as quickly as possible. It is possible for air to enter the lubricating system in conjunction with an oil or oil-filter change, or if the car has been stored for some time. This air can cause the hydraulic cam followers to emit a ticking noise, which can persist for up to 15 minutes after start- ing. Although this is quite normal and does not indicate any malfunction, it is advisable not to exceed 3,000 rpm before the noise has disappeared.

Starting and driving

135

The hydraulic cam lifters are completely service free; the valve clearance is set up at the factory and will not need any subse- quent adjustment. Starting the engine The engine has an automatic choke and should be started as follows: Cars with manual gearbox To start the engine the clutch pedal must be fully depressed. 1 Depress the clutch pedal but do not

touch the accelerator.

2 Start the engine. Let the ignition key

spring back as soon as the engine has started and is running smoothly – at very low temperatures, you may need to run the starter for up to 50 seconds.

Let the engine idle for about 10 seconds. Do not open the throttle wide for at least 2-3 minutes after starting. Cars with automatic transmission The selector lever must be in the P or N position. 1 Keep your foot on the brake pedal. 2 Start the engine. Let the ignition key

spring back as soon as the engine has started and is running smoothly – at very low temperatures, you may need to run the starter for up to 50 seconds.

Let the engine idle for about 10 seconds. Do not open the throttle wide for at least 2–3 minutes after starting.

136

Starting and driving

Useful tips on cold climate starting If the engine has failed to start after several attempts in very cold weather, press and hold the accelerator down to the floor and run the starter for 5–10 seconds. This will prevent the engine being flooded (exces- sively rich fuel-air mixture). Now start the engine in the normal way – do not touch the accelerator. If the engine stalls immediately after starting (e.g. if the clutch was released too quickly), do not touch the accelerator when restarting the engine. Every time the engine is switched off the spark plugs are automatically cleaned. If your attempt to start nevertheless fails, let go of the ignition key and allow it to spring back. This initiates more vigorous cleaning of the sparking plugs which goes on for about 5 seconds. Then start in the ordinary way. Do not touch the accelerator; if the accelerator is pressed to the floor the fuel supply is shut off.

Important considerations for driving The engine-management system in the Saab 9-3 is called Saab Trionic T7. The system manages the ignition, fuel injection and turbo boost pressure. The Trionic T7 system developed by Saab is an intelligent engine-management system designed to achieve optimum drive- ability under differing driving conditions. The system makes adjustments automati- cally, for instance, if the car is being driven at altitude (oxygen-deficient air), for differ- ent grades of fuel (AON 87–93) and for dif- ferent load conditions. 1 Starting and driving (cid:127) Refrain from using full throttle before

the engine has warmed up (before needle is in the mid-range on tempera- ture gauge) to avoid unnecessary wear. If the needle of the pressure gauge repeatedly enters the red zone the engine may suddenly lose power, owing to the intervention of a monitor- ing system which curtails the charging pressure. Get in touch with an autho- rized Saab dealer at once.

(cid:127) A safety function prevents the engine from revving faster than 6,200 rpm by temporarily shutting of the fuel injec- tors.

2 Stopping the engine (cid:127) Do not rev the engine immediately

before switching it off - stop the engine when it is idling.

3 Regulating the charging pressure (cid:127) The system is optimized for fuel with an octane rating of AON 90. For cars with 205 hp engines and the Viggen, the system is optimized for AON 93. One of the advantages of the system is that it enables the engine to be run safely on lower-grade fuel, although not lower than AON 87. However, engine perfor- mance will fall off slightly, and heavy loading should be avoided. For best performance you should use the rec- ommended grade of fuel, AON 90 (205 hp engine and Viggen AON 93).

(cid:127) The maximum boost pressure is

adjusted automatically to the knocking or pinging tendency of the engine. Occasional, short-lived knocking when the engine is under a heavy load is per- fectly normal; the extent will depend on the grade of fuel in the tank.

(cid:127) Isolated instances of knocking are

more likely to occur with low-octane fuel. This controlled form of knocking, followed by a reduction in the boost pressure, is a sign that the wastegate is functioning and is perfectly safe for the engine.

Saab 9-3 Viggen: The Saab 9-3 Viggen has a high-performance engine which means that a certain amount of care should be exercised, in particular when accelerating in the lower gears. This is especially important when the road surface is slippery to avoid the driving wheels losing their grip

NOTE

If constant knocking occurs every time a load is put on the engine, this indicates a malfunction in the system. Have the car checked without delay by an authorized Saab dealer.

NOTE

If the engine is being run with the car on a rolling road or dynamometer, longer than for a standard state emission inspection, to ensure adequate cooling, air must be blown into the engine compartment and under the car at a rate equivalent to the ram-air effect that would be obtained at the corresponding road speed.

Important considerations with cata- lytic converters The catalytic converter is an emission-con- trol device incorporated in the car’s exhaust system. It consists of a metal canister with a honeycomb insert, the cells of which have walls coated in a catalytic layer (mixture of precious metals).

NOTE

Use only unleaded gasoline. Leaded gas- oline is detrimental to the catalyst and oxygen sensor and will seriously impair the function of the catalytic converter.

To ensure that the catalytic converter con- tinues to function properly, and also to avoid damage to the converter and its associated components, the following points must be observed: (cid:127) Have the car serviced regularly in accor-

dance with the service program. The fuel and ignition systems are particularly important in this context.

(cid:127) Always be alert to any misfiring of the

engine (not running on all cylinders) and any loss of power or performance. At the first sign of a malfunction, reduce speed and take the car to an authorized Saab dealer as soon as possible. If the engine fails to start (in very cold weather or if the battery is dead), the car can be push started (manual gearbox only) or started using jumper cables to a donor battery. However, as soon as you

Starting and driving

137

Engine-management system with catalytic converter 1 Engine control module 2 Oxygen sensor (lambda probe) 3 Catalytic converter

have started the engine, it is important that it runs on all cylinders. If it is misfiring, allow it to idle for up to five minutes to give it time to settle and run smoothly. If, after this time, the engine still fails to run prop- erly, turn off the engine and get in touch with an authorized Saab dealer for advice. (cid:127) Never park the car on dry grass or other combustible material. The catalytic con- verter gets very hot and could therefore start a fire.

(cid:127) Never drive off if the engine is misfiring. If you jump start the car when the engine is already up to normal temperature, the engine must start to run on all cylinders.

(cid:127) (cid:127) 138

Starting and driving

Stop jump-starting if the engine fails to start immediately.

NOTE

If the car runs out of fuel, it is possible for air to get into the fuel system. If this happens, the catalytic converter may overheat and be damaged.

(cid:127) Failure to follow these directions could

result in the catalytic converter and asso- ciated components being damaged, and could represent a breach of the warranty conditions.

Refueling Ensure that you are using the correct grade of fuel, unleaded AON 87-93. For optimum performance we recommend: (cid:127) AON 90 for 2.0 Turbo 185 hp. (cid:127) AON 93 for 2.0 Turbo 205 hp and

2.3 Turbo Viggen.

If fuel containing a mixture of alcohol is used, the following restrictions apply: Methanol: max. 5% by volume. Ethanol: max. 10% by volume. MTBE: max. 15% by volume. The fuel filler cap is located in the right rear quarter panel. Switch off engine. Insert the fuel-pump nozzle beyond the flange on the filler pipe. Do not withdraw the nozzle while filling is in progress. Cease refuelling the first time the pump stops.

NOTE

Do not overfill. Fuel should not come right up the filler pipe as expansion room is needed.

Fuel-tank capacity: 17.0 US gal. (64 liters) Screw on the filler cap and keep turning until it has clicked at least three times. Manually opening the fuel filler door, see page 131, Convertible, page 52.

The most effective way to prevent conden- sation forming in the tank (and thus avoid possible running problems) is to keep the tank well filled. Before the onset of freezing temperatures in winter, it may be advisable to add gasoline anti-freeze to the fuel a few times to dispel any condensation in the system.

WARNING

(cid:127) Never use fuel for any purpose other

than as engine fuel.

(cid:127) Gasoline is highly flammable and can

cause severe burns. Never use an exposed flame in the vicinity of gaso- line. Never smoke when filling the vehicle up with gasoline.

NOTE

(cid:127) Fill to maximum filling capacity (cid:127) Stop filling after the first time that the nozzle trips to shut off the flow of fuel

(cid:127) Filling capacity can differ between different fuel stations and outside temperature. Fuel tank volume when nozzle trips to shut off, may vary by 0.5 gal. (2 liters).

(cid:127) Do not fill fuel all the way up the filler pipe. The gasoline must be allowed room for expansion especially during hot weather.

Recommended fuel: The engine in your Saab 9-3 is designed to operate on unleaded gasoline that has an octane rating of: (cid:127) AON 90 (minimum 87) for 185 hp

engines.

(cid:127) AON 93 (minimum 87) for 205 hp engines

and Viggen.

Octane rating is determined according to the formula:

MON + RON

where MON is the Motor Octane Number, and RON is the Research Octane Number. The average of these two values is the octane rating of the gasoline as it appears on the pump at a retail gas station. This value is sometimes referred to as the "Anti-Knock Index" (AKI) or the "Average Octane Number" (AON). To avoid deposit formation on the fuel injec- tors which can cause poor driveability, use only quality gasolines that contain deter- gents and corrosion inhibitors. Because gasolines sold at retail gas stations vary in their composition and quality, you should switch to a different brand if you begin expe- riencing driveability and/or hard starting problems shortly after refueling your car. In recent years, a variety of fuel additives and alcohols or oxygenates have been blended with gasoline. These types of gasolines may

Starting and driving

139

be found in all parts of the United States and Canada, but particularly in geographic areas and cities that have high carbon mon- oxide levels. Saab approves the use of such "reformulated" gasolines in its products, which help in reducing pollution from all motor vehicles, provided that the following blending percentages are met by such fuels: (cid:127) Up to 10% ethanol by volume, with corro-

sion inhibitors.

(cid:127) Up to 15% MTBE by volume (methyl ter-

tiary butyl ether).

(cid:127) Up to 5% methanol by volume, with an

equal amount of a suitable co-solvent and added corrosion inhibitors.

Other, less common, fuel additives used by some gasoline dealers are also acceptable, provided that the resultant gasoline is not more than 2.7% oxygen by weight. In many cases, you may not be able to determine the exact type or percentage by volume of fuel additive in the gasoline you purchase for your car. Some Canadian and U.S. gasolines contain an octane enhancing additive called meth- lycyclopentadienyl manganese tricarbonyl (MMT). If such fuel is used, your emission control system performance may deterio- rate and the malfunction indicator lamp on your instrument panel may turn on. If this occurs, return to your authorized Saab dealer for service. However, these blended gasolines are reg- ulated and should never exceed these rec-

140

Starting and driving

ommended blend percentages and service station operators should know if their gaso- lines contain detergents and oxygenates, and have been reformulated to reduce vehi- cle emissions. Nevertheless, if you begin to notice a problem with the way your car starts or runs shortly after it has been refueled, try a different brand of gasoline.

NOTE

Higher concentrations of methanol than listed above, or the use of methanol- blended gasoline without suitable co-solvents and corrosion inhibitors, can damage your car’s fuel system, leading to the need for repairs which are not covered by Saab’s product warranty.

NOTE

The engine control module (ECM) mon- itoring the engine parameters also stores fault codes. Under certain circumstances, this may cause constant illumination of the Engine malfunction (CHECK ENGINE) lamp , thus indicating a fault that must be checked by your Saab dealer, see page 57. NOTE: always observe the following two measures: (cid:127) Make sure that the fuel filler cap is

screwed on correctly before the engine is started. Screw on the fuel filler cap until you hear three distinct clicks.

(cid:127) Avoid driving with the fuel low level indicator illuminated. The symbol illuminates when less than approxi- mately 2.5 gallons (10 litres) of fuel remains in the tank.

Engine Break-in Period Pistons, cylinder bores and bearings need time to obtain uniform, wear-resistant sur- faces. If a new engine is driven too hard, this grad- ual process of bedding-in will not be possi- ble and the life of the engine will be short- ened. During the first 1,200 miles (2,000 km), do not exceed 5,000 rpm. In addition, refrain from driving the car at full throttle, other than for brief instances, during the first 1,800 miles (3,000 km). Wearing in new brake pads New brake pads take time to bed in, about 90 miles (150 km) if the car is driven largely under stop-and-go conditions or about 300 miles (500 km) of highway driving. To extend the useful life of the pads, avoid hard braking as much as possible. Wear indicators The outer brake pads on the front wheels have acoustic wear indicators, When 3 mm remain on the pads, a scraping or shrieking noise is heard on braking. When this occurs, the pads should be changed as soon as possible. Changing brake pads should only be carried out by an authorized Saab dealer.

Gear changing Manual transmission To start the engine the clutch pedal must be fully depressed. The gear positions are marked on the gear lever. Before reverse (R) can be engaged, you must lift the ring underneath the gear-lever knob. To change gear, fully depress the clutch pedal and then release it smoothly. It is inadvisable to drive with your hand resting on the gear lever, as this can increase the wear on the gearbox. When shifting down from 5th to 4th gear, ease the gear lever straight back, without applying any lateral pressure. This will pre- vent 2nd gear being engaged by mistake, which can result in overreving and possible damage to the engine.

NOTE

When the reverse gear is to be engaged the car must be at a standstill with the accelerator fully released. Lift the reverse lock-out collar and push the gear lever firmly to the right in neutral before easing it into reverse.

Shift-up indicator for improved fuel economy (U.S. models only) Cars equipped with a manual transmission have a "Shift-up" light on the instrument panel. The light begins to work after the vehicle is warmed up and provides you with a good indication when to shift to a higher gear. It is not necessary or recommended to follow the shift-up recommendations in all driving conditions, for example, when driv- ing in heavy urban traffic or steep downhill grades. However, shifting with the light should result in improved fuel economy. Therefore, for reduced fuel consumption and better energy conservation, you should make a habit of shifting before or when the shift-up light comes on.

Starting and driving

141

Automatic transmission

WARNING

(cid:127) Make it a habit to keep your foot on the brake when selecting a drive position, to prevent the car from creeping for- ward (or backwards if reverse is selected).

(cid:127) The car must be at a standstill before P, R or N is selected. You have to have your foot on the brake pedal to move the lever out of park. If the car is still moving when a drive position is subse- quently selected, this could cause an accident or damage the automatic transmission.

(cid:127) Never park the car with the selector lever in a drive position, even if the parking brake is on.

(cid:127) If you want to leave the car with the engine running, move the selector lever to P or N and apply the parking brake.

142

Starting and driving

Selector lever 1 Catch 2 Button for SPORT position 3 Button for WINTER position

R N D 3 2 1

Indication of gear position on the main instrument panel

Detent positions for selector movement

The electronic control module for the auto- matic transmission receives information on engine torque and road speed. It also con- trols the hydraulic pressure in the transmis- sion to ensure that gear changing is as smooth as possible. The position of the selector lever is shown by the symbols adjacent to the lever and also by an indicator on the main instrument panel. The ignition key can only be removed when the selector lever is in the P position.

When the car is stationary, the engine must be idling when the selector lever is moved. You must have your foot on the brake pedal to move the lever out of park. If the accelerator is depressed while the lever is moved, this will result in abnormal wear in the transmission.

NOTE

After selecting a drive position, pause briefly to allow the gear to engage (the car starts to pull a little) before you acceler- ate.

The detent button on the selector lever has to be pressed before the selector can be moved between certain positions. Three modes for the automatic transmis- sion can be selected: Normal, Sport and Winter. The Normal mode, which provides the best fuel economy, is the default setting when the engine is started. Sport mode alters the angle of the throttle valve for increased power compared to the same accelerator position in Normal mode. This means gear changes are made to opti- mize the car’s performance. The SPORT indicator light is shown on the main instru- ment panel; see page 147). The Winter mode is intended for use when pulling away and driving on icy roads. In this mode, the transmission starts in 3rd gear, to

provide better grip, and the WINTER indica- tor appears on the main instrument panel. When the ignition is turned to OFF, the auto- matic transmission will automatically revert to Normal mode (see page 147). Adaptive gear change pattern is a func- tion of the Normal and Sport modes. It allows gear changing to be suited to the pre- vailing driving conditions. The transmission control module senses the engine load and temperature of the transmission and selects one of the four available gear change pat- terns. Unnecessary gear changes and undesired temperature increases in the transmission are avoided. The automatic transmission has a special shift pattern during the first minute after a cold engine is started so that the catalytic converter will reach its correct working tem- perature more rapidly Lock-up function The automatic transmission has a lock-up function, which renders the torque con- verter inoperative in 2nd, 3rd and 4th gears. The result is reduction in the engine speed and, hence, fuel consumption. When the lock-up function comes into oper- ation, it may give the impression of an over- drive being engaged.

Shift Lock override

NOTE

Due to electrical problems it may not be possible to move the selector out of the park position, even if the ignition is ON. If for some reason the selector has to be moved out of the park position (i.e. to tow the car a short distance) do as described below.

1 Apply the parking brake. 2 Make sure the key is in the ON position. 3 Use a small tool such as a screwdriver and push the lever downwards so that the detent button can be pressed approx. 10 mm.

4 Move the selector out of position P to N. 5 Remove the tool. 6 Release the parking brake if the car is to be moved immediately; otherwise keep it applied.

Starting and driving

143

Check fuse No. 1 (see page 189). If the fuse is OK, check the battery voltage. If the problem was cured by changing the fuse or battery, you do not have to contact a Saab dealer. If the fuse blows again as soon as the Shift Lock feature is activated you should contact your Saab dealer.

144

Starting and driving

Automatic transmission fault indicator

NOTE

If the symbol appears on the main instru- ment panel, the system has detected a fault in the automatic transmission or its control module (see page 58). This also means that the Limp-home mode has been selected, to guard against further damage being done to the transmission. In this mode, the automatic transmission starts in 4th gear, and gear changes (if nec- essary) will have to be made manually. It is not possible to select the SPORT or WINTER mode when the Limp-home mode is active. You should have the automatic transmis- sion checked as soon as possible by an authorized Saab dealer. The following gears will be engaged in the respective selector positions when the auto- matic transmission is in the Limp-home mode:

Position R

Gear

Reverse 4th 4th 3rd 3rd

If the control module has actuated the Limp-home function for the automatic transmission, the car will remain in 4th gear when D is selected, making it very sluggish. To overcome this, move the selector lever to position 2.

Overheated transmission oil If the transmission oil becomes overheated while driving, the following message appears on the SID: TRANSMISSION OVERHEATING. In this event, stop the car in a suitable place, switch off the engine, open the hood and wait until the message goes out. When driving subsequent to the transmission oil overheating, select a locked gear position in which the engine speed is about 3,000 rpm. The transmission oil can become very hot when the car is driven with a heavy load; for example, driving with a trailer on hilly roads when the wrong gear has been selected, resulting in many extra gear changes. Select one of the positions 1, 2 or 3. A high outside temperature or a defective oil cooler can also cause the oil temperature to increase. Contact an authorized Saab work- shop, see also page 156.

Driving in hilly country with a heavy load Overheating of the automatic-transmission fluid can occur when the car is towing a heavy load, such as a trailer in hilly country, with the wrong gear selected, resulting in abnormally frequent gear changing. Try selecting position 1, 2 or 3. High ambient temperatures can also increase the temper- ature of the transmission fluid or the oil cooler may be faulty. As the transmission fluid temperature increases, its useful ser- vice life is reduced. Contact an authorized Saab dealer (see also page 156).

WARNING

Remember to use engine-braking (selec- tor position 1, 2, or 3) to spare the brakes when you are driving on a long or steep downhill slope. Select the same gear as you would on the corresponding uphill slope. Brake failure can result from overheated brakes!

Towing Towing a car with automatic transmission, see page 162.

Selector positions

To shift out of the P position you must depress the brake pedal and the ignition must be ON. The parking position (P) must only be selected when the car is at a complete standstill. The selec- tor lever is locked and the transmission is mechanically immobilized. Always apply the park- ing brake after parking the car. The engine can be started. The reverse (R) position must only be selected when the car is at a complete standstill. The detent-release button must be pressed before the selector lever can be moved to R. Wait until reverse gear has engaged (car starts to creep) before touching the accelerator.

In the Neutral position (N), the transmission is dis- engaged from the engine. The engine can be started, but first ensure that the parking brake is on, to prevent the car from moving off unexpect- edly. To prevent the engine and transmission from becoming hotter than necessary, select N for stops other than brief ones, e.g. if stuck in a traffic jam. The normal drive position (D) is recommended for waiting at traffic lights.

Starting and driving

145

The Drive position (D) is the position for normal motoring. Gear changes between 1st and 4th will take place automatically, the timing of which is determined by the throttle (accelerator) position and the speed of the car. After moving the selector lever to D, pause to give the gear time to engage (car starts to pull). In position 3, 4th gear is locked out. The car will start in 1st gear and normal gear changing (up and down) will take place automatically between gears 1, 2 and 3. Position 3 is recommended on roads with fre- quent bends and in congested traffic. Moving the selector lever from D to 3 will cause a downshift to 3rd gear, which will give better engine-braking. Do not move the selector to position 3 at speeds in excess of 90 mph (150 km/h). Position 2 is recommended in hilly country. This gear enables the performance of the engine to be exploited better and also provides effective engine-braking. Normal gear changing (up and down) between 1st and 2nd gear will take place automatically. Third and 4th gears are locked out. Do not move the selector to position 2 at speeds in excess of 70 mph (110 km/h).

146

Starting and driving

Position 1 should be used when maximum engine-braking is required on steep downhill slopes and to avoid frequent gear-changing on steep climbs. Do not move the selector to position 1 at speeds in excess of 30 mph (50 km/h).

If the gear selector lever is moved from position D to 1, a change-down to 3rd gear will occur at about 110 mph (180 km/h). A change-down to 2nd gear will occur at about 75 mph (120 km/h) and to 1st gear at about 40 mph (65 km/h). When position 1 is selected, all the other gears will be locked out. Manual gear-changing is not recommended on slippery roads. 2.0 Turbo 185 hp and 205 hp: If one of the drive wheels spins excessively, the engine torque will be reduced to avoid damaging the transmission Kick-down When the accelerator is pressed down hard, a downshift to the next lower gear will occur to provide maximum acceleration, e.g. for over- taking. The change-up to the next gear again will take place either when the accelerator is released or when maximum engine speed for that gear is reached.

Adaptive gear-change patterns Adaptive gear-change patterns are selected automatically depend- ing on the engine load. This function applies in the Normal and Sport modes. The change occurs at a higher rotation speed and the gear remains engaged for a longer period, if the control module senses that the load does not drop. These change patterns avoid unnecessary gear changes when, for example, driving on long inclines with a trailer, and to prevent overheating of the transmission oil. This function cuts in automatically if the oil becomes too hot, to protect the transmis- sion from serious damage, and lower the oil temperature. The adaptive change pattern function is not activated at speeds over 93 mph (150 km/h). If a pattern is in operation when this speed is exceeded, it will be maintained until the control module senses that a more suitable one can be activated. The adaptive gear-change pattern function is deselected when: (cid:127) Winter mode is selected. (cid:127) The engine is switched off. (cid:127) The load is reduced by so much that this function is no longer

required.

“Automatic transmission fault indicator” appears on the

main instrument panel, see page 144.

(cid:127) The SPORT and WINTER modes

To select Sport mode, press the ”S” button on the selector lever when the selector lever is in position N, D, 3, 2 or 1. In this mode, gear changes will take place at higher engine speeds than in Normal mode, in other words, the transmission will shift up later and shift down earlier for the same throttle (accel- erator) position. The Sport mode will be deselected if: (cid:127) The S button is pressed. (cid:127) The selector lever is moved to position P or R. (cid:127) The engine is switched off. (cid:127) The Winter mode is selected.

“Automatic transmission fault indicator” appears on main instrument panel, see page 144.

Starting and driving

147

The Winter mode facilitates starting off and driv- ing on icy roads. Third gear is selected automati- cally for starting off to reduce wheelspin. Winter mode can be selected when the engine is running by pressing the ”W” button on the selec- tor-lever surround. It cannot be selected when the selector lever is in position 2 or 1. Note: It is still possible to use kick-down in the Winter mode, in which case a change-down to 2nd or 1st will take place. The Winter mode will be deselected if: (cid:127) The W button is pressed. (cid:127) The engine is switched off. (cid:127) The selector lever is moved to position 2 or 1. (cid:127) Kick-down is activated. (cid:127) The automatic-transmission fluid overheats.

“Automatic transmission fault indicator” appears on main instrument panel, see page 144.

(cid:127) (cid:127) Starting and driving

148
Cruise Control

WARNING

(cid:127) Do not use the Cruise-control system on wet or icy roads, in dense traffic or on winding roads

(cid:127) To prevent the system being activated inadvertently, set the control to OFF when you do not want to use the system

The system is operated by means of the controls on the stalk switch: (cid:127) OFF (system is disconnected; the system

is always in the OFF position when the engine is started).

(cid:127) ON (system switched on). (cid:127) SET/+ (to set the desired speed). (cid:127) CANCEL (cancel operation of system,

e.g. to reduce speed temporarily).

(cid:127) RES/– (resume preset speed). When the system is ON, the CRUISE indi- cator light will appear on the main instru- ment panel and will be extinguished when the system is switched OFF. If CANCEL is selected, CRUISE will flash off once.

Temporary increase in speed Press the accelerator to override the preset speed, e.g. for overtaking. When you release the accelerator, the system will revert to the preset speed. To cancel temporarily Move the control stalk to CANCEL (spring-loaded position before OFF posi- tion). This will disengage the system but the preset speed will be retained in the system memory. (The memory is deleted when the engine is switched off.) To re-engage the system To revert to the preset speed, slide the switch to RES/–. This will only operate when the car’s speed is above 25 mph (40 km/h). To reduce the preset speed The cruise-control system will always disen- gage automatically the moment that either the brake pedal or the clutch pedal is depressed. It is also possible to reduce the speed by: (cid:127) Sliding the button to RES/– once will

reduce the speed by 1 mph (1.6 km/h). (cid:127) Holding the button in the RES/– position will effect a gradual reduction in speed until the button is released.

To set the desired speed Move the switch to ON. Accelerate to the desired speed (minimum speed: 25 mph (40 km/h) and press SET/+. To increase the preset speed Accelerate to the desired speed and press SET/+. You can also increase the speed of the car using the SET/+ button. Press it once to increase the speed by 1 mph (1.6 km/h) or hold it in and release when the desired speed is reached.

Disengaging the system The system will be disengaged: (cid:127) When the brake or clutch pedal is

depressed.

(cid:127) When the switch is moved to CANCEL. (cid:127) When the switch is moved to OFF. (cid:127) When the engine is switched off. (cid:127) When the selector lever is moved to posi- tion N (cars with automatic transmission).

Braking To avoid overheating the brakes, (e.g. when negotiating long descents with a drop of several hundred feet), select a low gear to use the braking effect of the engine. If the car has automatic transmission, move the selector lever to position 1 or 2. When driving fast, you can help to prolong the life of the brakes by thinking ahead and braking harder for short periods, rather than braking more moderately over long stretches. Brake pad wear indicators The outboard brake pads on the front wheels incorporate pad-wear indicators. When the lining is down to 3 mm, the pad will produce a screeching, squealing or scraping noise when the brakes are applied. New pads should be installed without delay. Brake pads should only be replaced by an authorized Saab dealer. To ensure optimum brake performance, it is recommended that you use only Saab original brake pads.

Starting and driving

149

WARNING

(cid:127) It is prudent to try your brakes from

time to time, especially when driving in heavy rain, on roads with a lot of sur- face water, or in snow or slush. In such conditions, the brakes may take longer than normal to take effect. To rectify this, touch the brake pedal peri- odically to dry the brakes out.

(cid:127) The same applies after the car has

been washed or when the weather is very humid.

(cid:127) The brakes are power assisted and it should be kept in mind that the servo unit only provides the power assis- tance when the engine is running.

(cid:127) The brake pressure required when the

engine is off,( e.g. when the car is being towed) is roughly four times the normal pedal force required. The pedal also feels hard and unrespon- sive.

150

Starting and driving

ABS brakes

WARNING

(cid:127) The additional safety afforded by the ABS system is not designed to allow drivers to drive faster but to make normal driving safer.

(cid:127) To stop as quickly as possible, without

loss of directional stability, whether the road surface is dry, wet or slippery, press the brake pedal down hard without letting up (do not pump the pedal), declutching simulta- neously, and steer the car to safety.

ABS (Antilock Braking System) modulates the brake pressure to the respective wheels. Wheel sensors detect if a wheel is about to lock, and the control module reduces the pressure to that wheel and then increases it once more until the tendency is detected again. The brake system is equipped with an Elec- tronic Brake-force Distribution device (EBD), which distributes the brake pressure between the front and rear wheels in such a way as to achieve optimum braking perfor- mance regardless of the car’s speed and load. The ABS system has a built-in diagnostic function which will switch on the ABS warn- ing light if a fault is detected in the system (see page 56).

ABS braking - confirmation that the sys- tem is operating

Braking with ABS - evasive steering

The ABS system will not reduce the braking distance on loose gravel or on snow or ice but, because the wheels cannot lock up, some steering control is retained. When the ABS system is working, i.e. mod- ulation of the brake pressure is in progress, the brake pedal will pulsate and a ticking noise will be heard. All this is perfectly nor- mal. Press the pedal down hard (you cannot press too hard) and steer the car to safety.

Do not release the brake pedal before the car has come to a halt or the danger is past! This is critical. If the road is slippery, the ABS system will operate even when only light pressure is applied to the pedal. This means that you can brake gently to test the condition of the road and adapt your driving accordingly. It is well worth practising the use of ABS brakes on a skid pad or other suitable facil- ity.

Parking brake The parking brake lever is located between the front seats. The brake acts on the rear wheels. When the parking brake is on, the indicator lamp on the main instrument panel will be lit. To release the brake, lift the lever slightly, press the pawl button, and let the lever down. Always apply the parking brake when you park.

Parking

WARNING

(cid:127) Park where the vehicle will not create

an obstruction or a hazard to other road users.

(cid:127) Do not park on dry grass or other com-

bustible material. The catalytic con- verter gets very hot and could start a fire.

(cid:127) Do not leave children or pets unat- tended in the car. In warm, sunny weather, the temperature inside the car can reach 160–180°F (70–80°C).

NOTE

(cid:127) Apply the parking brake. (cid:127) Shift into Reverse for manual trans-

mission; for automatic transmission: move selector lever to P (Park)), and remove the ignition key.

(cid:127) Lock the car.

Starting and driving

151

NOTE

Saab 9-3 Viggen: The body design together with the relatively low ground clearance of the car means that great care must be taken during parking to avoid damage to the under part of the bumper.

152

Starting and driving

(cid:127) Wash and wax the car. Clean the rubber seals on the hood, trunk lid and doors, and lubricate them with glycerol (glyc- erin).

(cid:127) After washing the car, dry the brake discs

by taking the car out on the road and applying the brakes a few times.

(cid:127) Fill the fuel tank with fuel to prevent con-

densation forming in it.

1 Pointing downhill and

against the curb – Turn the wheels into the curb and edge the car for- ward until the wheels touch the curb.

2 Pointing uphill and

against the curb – Turn the wheels away from the curb and edge the car back until the wheels touch the curb.

3 Pointing uphill or down-

hill – no curb – Turn the wheels towards the edge of the road. If the car should start rolling, it will not run into the road.

Parking on a hill When parking on a steep hill, turn the front wheels so that they will be blocked by the curb if the car should move.

Long-term parking If the car is not going to be used for some time, e.g. 3–4 months, the following steps