Login- Download PDF Manual
-
installing a child-restraint system on the front passenger seat, install the child-restraint system on the rear seat and consult an Authorized Mazda Dealer as soon as possible.
Driver and front passenger buckle switches The buckle switches on the front seat belts detect whether or not the front seat belts are securely fastened and further control the deployment of the air bags.
2-50
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page63
Thursday, July 7 2005 1:2 PMBlack plate (63,1)
Essential Safety Equipment SRS Air Bags
qHow the Side and Curtain Air Bags Work When air bag crash sensors detect a side impact of greater than moderate force, an electrical current is sent to the inflators. Gases are produced to inflate the side and curtain air bags and after the inflation, the side and curtain air bags quickly deflate. The side and curtain air bags will function only once. After that, the side and curtain air bags will not work again and must be replaced. Only an Authorized Mazda Dealer can replace the systems.
The side and curtain air bag will deploy only on the side the vehicle receives the force of the impact.
WARNING
Damaged Side and Curtain Air Bag Wiring under the Front Seats: Placing luggage or other objects under the front seats is dangerous. The side and curtain air bag wiring could be damaged, and in the event of a side collision, the side and curtain air bags may not deploy, which could result in death or serious injury. To prevent damage to the side and curtain air bag wiring, do not place luggage or other objects under the front seats.
qAir Bag Activation/Deactivation
NOTE
If the front passenger seat weight sensors detect a total seated weight on the front passenger seat is less than approximately 42 kg (93 lb), the front passenger front and side air bags and seat belt pretensioner may not inflate (page 2-46).
Form No.8U01-EA-05H
2-51
Mazdaspeed6_8U01-EA-05H_Edition1 Page64
Thursday, July 7 2005 1:2 PMBlack plate (64,1)
Essential Safety Equipment SRS Air Bags
Front air bag activation A greater than moderate impact will cause the front air bags to inflate in the following cases: l Hitting a solid wall straight on at
greater than about 22 km/h (14 mph).
l Hitting a curb, pavement edge or hard
object.
l Driving into a big hole or hitting the far
side of a hole.
Limitations to front air bag activation Depending on the severity of impact, the front air bags may not inflate in the following cases: l Impacts involving trees or poles cause severe cosmetic damage but may not have enough stopping force to activate the air bag.
l Landing hard or the vehicle falling.
l Frontal offset impact to the vehicle may not provide the stopping force necessary for air bag deployment.
l Frontal impact within about a 30
degree range from head-on to the vehicle.2-52
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page65
Thursday, July 7 2005 1:2 PMBlack plate (65,1)
Essential Safety Equipment SRS Air Bags
l Rear-ending or running under a truck's tail gate may not provide the stopping force necessary for air bag deployment.
Side and curtain air bag activation Greater than moderate impact to one side of the vehicle (driver or passenger side areas) will cause the side and curtain air bags on that side to inflate, but it will not normally deploy the front air bags.
Non-activation of front air bags Front air bags will not normally inflate in the following cases: l Collision from the rear.
l Impact to the side, but it may deploy
the side and curtain air bags.
Limitations to side and curtain air bag activation Depending on the severity of impact, the side and curtain air bags may not inflate in the following cases: l Frontal offset impact may not provide enough side impact to deploy the side and curtain air bags.
l Vehicle roll-over, may deploy the side
and curtain air bags but not the front air bags.
l Side impacts involving trees or poles
can cause severe cosmetic damage but may not have enough impact force to activate the side and curtain air bags.
Form No.8U01-EA-05H
2-53
Mazdaspeed6_8U01-EA-05H_Edition1 Page66
Thursday, July 7 2005 1:2 PMBlack plate (66,1)
Essential Safety Equipment SRS Air Bags
l Vehicle roll-over may not provide
enough side force to deploy the side and curtain air bags.
l Side impacts with two-wheeled
vehicles may not provide enough force to deploy the side and curtain air bags.
Non-activation of side and curtain air bag The side and curtain air bags will not normally inflate in the following cases: l Collision from the rear.
l Collision from the front, but it may
deploy the front air bags.
2-54
Form No.8U01-EA-05H
qConstant Monitoring The following components of the air bag systems are monitored by a diagnostic system:
l SAS unit l Front air bag sensor l Air bag modules l Side crash sensors l Front seat belt pretensioners l Related wiring l Driver seat slide position sensor l Front passenger seat weight sensors l Driver and front passenger seat belt
buckle switches
The diagnostic module continuously monitors the system's readiness. This begins when the ignition switch is turned to the ON position and continues while the vehicle is being driven.
qAir Bag/Front Seat Belt
Pretensioner System Warning Light
If the air bag/front seat belt pretensioner system is normal, the warning light illuminates when the ignition switch is turned to the ON position or after the engine is cranked. After about 6 seconds it goes out.
Mazdaspeed6_8U01-EA-05H_Edition1 Page67
Thursday, July 7 2005 1:2 PMBlack plate (67,1)
Essential Safety Equipment SRS Air Bags
A system malfunction is indicated when the warning light constantly flashes, constantly illuminates or doesn't illuminate at all when the ignition switch is turned to the ON position. If any of these occur, consult an Authorized Mazda Dealer as soon as possible. The system may not work in an accident.
l Front passenger air bag deactivation
indicator light does not illuminate when the ignition switch is turned to the ON position or does not illuminate as indicated in the chart. For more details about this indicator light and this chart, refer to “Front passenger seat weight sensors” (page 2-46).
WARNING
WARNING
Self-Servicing the Air Bag/ Pretensioner Systems: Self-servicing or tampering with the systems is dangerous. An air bag/ pretensioner could accidentally activate or become disabled. This could cause serious injuries. Never tamper with the systems and always have an Authorized Mazda Dealer perform all servicing and repairs.
qMaintenance The air bag systems do not require regular maintenance. But if any of the following occurs, take your vehicle to an Authorized Mazda Dealer as soon as possible: l The air bag system warning light
flashes.
l The air bag system warning light
remains illuminated.
l The air bag system warning light does not illuminate when the ignition switch is turned to the ON position. l The air bags have deployed.
Damaged Air Bag/Seat Belt Pretensioner System Components: Expended or damaged air bag or seat belt pretensioner units must be replaced after any collision which caused them to deploy or damage them. Only a trained Authorized Mazda Dealer can fully evaluate these systems to see that they will work in the next accident. Driving with an expended or damaged air bag or pretensioner units will provide you reduced protection in the next accident and you could be injured or killed.
Removing Interior Parts: Removing any components such as the front seats, front dashboard, the steering wheel or parts on the front and rear window pillars and along the roof edge, containing air bag parts or sensors is dangerous. These parts contain essential air bag components. The air bag could accidentally activate and cause serious injuries. Always have an Authorized Mazda Dealer remove these parts.
Form No.8U01-EA-05H
2-55
Mazdaspeed6_8U01-EA-05H_Edition1 Page68
Thursday, July 7 2005 1:2 PMBlack plate (68,1)
Essential Safety Equipment SRS Air Bags
WARNING
Air Bag Disposal: Improper disposal of an air bag or a vehicle with live air bags in it can be extremely dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
NOTE
If it becomes necessary to have the components or wiring system for the supplementary restraint system modified to accommodate a person with certain medical conditions in accordance with a certified physician, contact an Authorized Mazda Dealer, refer to “Customer Assistance (U.S.A.)” (page 9-2).
2-56
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page69
Thursday, July 7 2005 1:2 PMBlack plate (69,1)
3 Knowing Your Mazda
Explanation of basic operations and controls; opening/closing and adjustment of various parts.
Advanced Keyless Entry and Start System ................................ 3-2
Advanced Keysí ...................................................................... 3-2
Operation Using Advanced Keyless Functions ......................... 3-7
Operation Using Advanced Key Functions ............................. 3-13
Warning and Beep Sounds ...................................................... 3-16
Setting Change (Function Customization) .............................. 3-18
User Mis-Operation Warning Indicators ................................. 3-19Doors and Locks ......................................................................... 3-20
Keys ........................................................................................ 3-20
Keyless Entry System (with Retractable Type Key) ............... 3-21
Door Locks ............................................................................. 3-26
Trunk Lid ................................................................................ 3-29
Inside Trunk Release Lever ..................................................... 3-33
Power Windows ...................................................................... 3-34
Opening/Closing the Power Windows from Outside .............. 3-39
Fuel-Filler Lid and Cap ........................................................... 3-42
Hood ....................................................................................... 3-44
Moonroofí ............................................................................. 3-45Security System ........................................................................... 3-47
Immobilizer System (with Advanced Key) ............................. 3-47
Immobilizer System (without Advanced Key) ........................ 3-50
Theft-Deterrent System ........................................................... 3-53Steering Wheel and Mirrors ...................................................... 3-55
Steering Wheel ........................................................................ 3-55
Mirrors .................................................................................... 3-55íSome models.
3-1
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page70
Thursday, July 7 2005 1:2 PMBlack plate (70,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Advanced Keysí
The advanced keyless functions (advanced keyless entry and start system) enables the following operations while the advanced key is being carried (page 3-7). l Locking/unlocking the doors and the trunk lid without operating the key. l Starting the engine without operating the key. The advanced key enables additional functions other than those with the advanced keyless functions (page 3-13). l The following operations are possible using the keyless entry system from a distance
(Lock/Unlock/Panic button): l Locking/unlocking the doors and the trunk lid. l Opening the power windows. l Turning on the alarm.
l Locking/unlocking the doors and the trunk lid, or starting the engine using the auxiliary
key.
WARNING
Keys and Children: Leaving children in a vehicle with the key is dangerous. This could result in someone being badly injured or even killed. These new kinds of keys are fascinating to children. They could play with power windows or other controls, or even make the vehicle move. Don't leave the keys in your vehicle with children and keep them in a place where your children will not find or play with them.
Use of Advanced Key Near Medical Equipment: Radio waves from the advanced key may affect medical equipment such as pacemakers. Before using the advanced key near people who use medical equipment, ask the medical equipment manufacturer or your physician if radio waves from the advanced key will affect the equipment.
NOTE
l The driver must carry the advanced key to ensure the system functions properly. l Refer to Immobilizer System (page 3-47) for information regarding keys and engine
starting.
l Refer to Theft-Deterrent System (page 3-53) for information regarding keys and the
prevention of vehicle and vehicle contents theft.
3-2
íSome models.
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page71
Thursday, July 7 2005 1:2 PMBlack plate (71,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Your Mazda has two kinds of keys.
Master key
Panic button
Lock button
Unlock button
Valet key
Auxiliary key
Operation indicator light
Here's what the keys are used for:
Key code number plate
Lock Operates
Master key
Valet key
Ignition switch and steering column lock
Driver's door Glove box Trunk lid
Yes Yes Yes Yes
Yes Yes No No
If you must leave your vehicle with another person, such as a parking attendant, protect items by locking the glove box, and trunk lid with the master key. Keep that key and give the other person only the valet key.
A code number is stamped on the plate attached to the key set; detach this plate and store it in a safe place (not in the vehicle) for use if you need to make a replacement key.
Also write down the code number and keep it in another safe and handy place, but not in the vehicle.
If your key is lost, consult your Authorized Mazda Dealer with the code number ready.
Form No.8U01-EA-05H
3-3
Mazdaspeed6_8U01-EA-05H_Edition1 Page72
Thursday, July 7 2005 1:2 PMBlack plate (72,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
CAUTION
l Because the advanced key uses low-intensity radio waves, it may not function
correctly under the following conditions: l The advanced key is carried with communication devices such as cellular phones. l The advanced key contacts or is covered by a metal object. l The advanced key is near electronic devices such as personal computers. l Non-Mazda genuine electronic equipment is installed in the vehicle. l There is equipment which discharges radio waves near the vehicle.
If the vehicle is near equipment such as wireless pay devices installed at certain gas stations.
l The advanced key may consume battery power excessively if it receives high-
intensity radio waves. Do not place the advanced key near electronic devices such as televisions or personal computers.
l To avoid damage to the advanced key, DO NOT:
l Drop the advanced key. l Get the advanced key wet. l Disassemble the advanced key. l Expose the advanced key to high temperatures on places such as the dashboard or
hood, under direct sunlight.
l Place heavy objects on the advanced key. l Put the advanced key in an ultrasonic cleaner. l Put any magnetized objects close to the advanced key.
NOTE
l Battery life is about one year. Replace the battery when the KEY indicator light
(green) flashes in the instrument cluster. Refer to Advanced Key Dead Warning on page 3-17.
l Additional advanced keys can be obtained at an Authorized Mazda Dealer. Up to 6
advanced keys can be used with the advanced keyless functions per vehicle.
3-4
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page73
Thursday, July 7 2005 1:2 PMBlack plate (73,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
qAdvanced Key Maintenance
CAUTION
l Make sure the battery is installed
with the correct pole facing upward. Battery leakage could occur if it is not installed correctly.
l When replacing the battery, be
careful not to bend the electrical terminals or get oil on them. Also be careful not to get dirt in the transmitter as it could be damaged. l There is the danger of explosion if
the battery is not correctly replaced.
l Replace only with the same type battery (CR2025 or equivalent).
l Dispose of used batteries according
to the following instructions.
Insulate the plus and minus terminals of the battery using cellophane or equivalent tape.
l Never disassemble. l Never throw the battery into fire
or water.
l Never deform or crush.
The following conditions indicate that the battery power is low: l The KEY indicator light (green) flashes
in the instrument cluster when the engine is turned off.
l The system does not operate and the
operation indicator light does not flash when the buttons are pressed.
l The system's operational range is
reduced.
Replacing the battery at an Authorized Mazda Dealer is recommended to prevent damage to the advanced key. If replacing the battery by yourself, follow the instruction below.
Replacing the advanced key battery
1. Pull out the auxiliary key.
2. Release the cap using a flathead
screwdriver, then rotate and remove the cap.
Cap
CAUTION
Do not turn the cap excessively. The cap may be damaged.
3-5
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page74
Thursday, July 7 2005 1:2 PMBlack plate (74,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
3. Insert a flathead screwdriver into the
crack and press the battery out.
4. Insert the new battery (CR2025 or equivalent) with the positive pole ( facing the (
) mark on the cap.
qService If you have a problem with the advanced keyless functions, consult an Authorized Mazda Dealer.
If your advanced key is lost or stolen, bring all remaining advanced keys to an Authorized Mazda Dealer as soon as possible for a replacement and to make the lost or stolen advanced key inoperative.
CAUTION
Radio equipment like this is governed by laws in the United States. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
5. Rotate and close the cap.
Cap
6. Reinsert the auxiliary key.
3-6
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page75
Thursday, July 7 2005 1:2 PMBlack plate (75,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
NOTE
The system may not operate if you are too close to the windows, door handles, or trunk lid.
Starting the engine The operational range for starting the engine includes nearly the entire cabin area except for the trunk.
Interior transmitter
Operational range
Operation Using Advanced Keyless Functions qOperational Range The system operates only when the driver is in the vehicle or within operational range while the advanced key is being carried.
NOTE
When the battery power is low, or in places where there are high-intensity radio waves or noise, the operational range may become narrower or the system may not operate.
Locking, unlocking the doors and the trunk lid The operational range for locking/ unlocking the doors is up to 80 cm (2.6 ft) from the center of the front door handles. The operational range for locking/ unlocking the trunk lid is up to 80 cm (2.6
ft) from the center of the trunk lid.Exterior transmitter
Operational range
Form No.8U01-EA-05H
3-7
Mazdaspeed6_8U01-EA-05H_Edition1 Page76
Thursday, July 7 2005 1:2 PMBlack plate (76,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
qLocking, Unlocking with Request
Switch
All doors and the trunk lid can be locked/ unlocked by pressing the request switch on the front doors or the trunk lid while the advanced key is being carried. Front doors
Request switch
Trunk lid
Request switch
To lock To lock the doors and the trunk lid, press the request switch. A beep sound will be heard once and the hazard warning lights will flash once.
NOTE
l The trunk is out of the operational range, however, starting the engine may be possible.
l The engine may not start if the advanced key is placed in the following areas: l Around the dashboard
In the storage compartments such as the glove box
l On the rear parcel shelf
l Starting the engine may be possible even if the advanced key is outside of the vehicle and extremely close to a door and window, however, always start the engine from the driver's seat. If the vehicle is started and the advanced key is not in the vehicle, the vehicle will not restart after it is shut off and the ignition switch is turned to the lock position.
l If the advanced key is detected
within operational range, the operation indicator light flashes momentarily.
3-8
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page77
Thursday, July 7 2005 1:2 PMBlack plate (77,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
To unlock
Driver's door request switch To unlock the driver's door, press the request switch. A beep sound will be heard twice and the hazard warning lights will flash twice. To unlock all doors and the trunk lid, press the request switch again within 5
seconds and two more beep sounds will be heard.Front passenger door/trunk lid request switch To unlock the doors and the trunk lid, press the request switch. A beep sound will be heard twice and the hazard warning lights will flash twice.
NOTE
l The request switch on the trunk lid
can also set so that it cannot be unlocked with the valet key, refer to Trunk Security (page 3-31).
l The request switch on the driver's
door can be used to close the power windows, refer to Opening/Closing Power Windows from Outside (page 3-39).
l Confirm that all doors and the trunk
lid are securely locked.
l All doors and the trunk lid cannot be
locked when any door or the trunk lid is open.
l A beep sound is heard for
confirmation when the doors and the trunk lid are locked/unlocked using the request switch. If your prefer, the beep sound can be turned off (page 3-18).
Form No.8U01-EA-05H
NOTE
l The setting can be changed so that
the doors and the trunk lid are locked automatically without pressing the request switch. (Auto-lock function) A beep sound is heard when all doors and the trunk lid are closed while the advanced key is being carried. All doors and the trunk lid are locked automatically after about 3 seconds when the advanced key is out of the operational range. Also, the hazard warning lights flash once. (Even if the driver is in the operational range, all doors and the trunk lid are locked automatically after about 30 seconds.) If you are out of the operational range before the doors and the trunk lid are completely closed, the auto- lock function will not work. Always make sure that all doors and the trunk lid are locked before leaving the vehicle (page 3-18). The auto-lock function does not close the power windows.
l After unlocking doors and the trunk lid by pressing the request switch, all doors and the trunk lid will automatically lock and the hazard warning light will flash if any of the following operations are not performed within about 30 seconds. l A door or the trunk lid is opened. l The auxiliary key is inserted into
the ignition switch.
l The start knob is pushed.
3-9
Mazdaspeed6_8U01-EA-05H_Edition1 Page78
Thursday, July 7 2005 1:2 PMBlack plate (78,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
NOTE
If turning the ignition switch is difficult, jiggle the steering wheel from side to side.
ACC(Accessory) The steering wheel unlocks and some electrical accessories will operate.
NOTE
The Advanced Keyless Entry System does not function in the ACC position, and the doors will not lock/unlock even if they have been locked manually or the advanced key is carried away from the vehicle.
ON This is the normal running position after the engine is started. The warning lights (except brakes) should be inspected before the engine is started (page 5-24).
NOTE
When the ignition switch is turned to the ON position, the sound of the fuel pump motor operating near the fuel tank can be heard. This does not indicate an abnormality.
START The engine is started in this position. It will crank until you release the start knob; then it returns to the ON position. The brake warning light can be checked after the engine is started (page 5-24).
qStarting the Engine Ignition Switch Positions Without a traditional key, some of the ignition switch functions are different.
Start knob
LOCK(Released) The steering wheel locks to help protect against theft.
LOCK(Depressed) The ignition switch can be turned to the ACC position when the KEY indicator light (green) illuminates in the instrument cluster.
WARNING
Not Setting the Parking Brake: Leaving the driver's seat without setting the parking brake is dangerous. Unexpected vehicle movement could occur if the parking brake is not set. This could cause an accident. Before leaving the driver's seat, always set the parking brake and make sure the shift lever is in 1 or R.
3-10
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page79
Thursday, July 7 2005 1:2 PMBlack plate (79,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Starting the Engine
NOTE
l Engine-starting is controlled by the
spark ignition system. This system meets all Canadian Interference-Causing Equipment Standard requirements regulating the impulse electrical field strength of radio noise.
l The advanced key must be carried
because the advanced key carries an immobilizer chip that must communicate with the engine controls at short range.
l When starting the engine, be sure the start knob is securely attached before trying to operate it. If the knob becomes detached from the ignition switch, re-attach it by pushing it on to the ignition switch.
5. Depress the clutch pedal all the way
and shift into neutral. Keep the clutch pedal depressed while cranking the engine.
NOTE
The starter will not operate if the clutch pedal is not depressed all the way.
6. Push the start knob slowly all the way
in.
7. Verify that the KEY indicator light
(green) illuminates in the instrument cluster. The KEY warning light (red) means you cannot continue to start the engine (page 3-19).
1. Make sure the advanced key is being
carried.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Depress the brake pedal.
Form No.8U01-EA-05H
3-11
Mazdaspeed6_8U01-EA-05H_Edition1 Page80
Thursday, July 7 2005 1:2 PMBlack plate (80,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
CAUTION
Don't try the starter for more than 10
seconds at a time. If the engine stalls or fails to start, wait 10 seconds before trying again. Otherwise, you may damage the starter and drain the battery.10. After starting the engine, let it idle for
about 10 seconds.
NOTE
l In extremely cold weather, below _18° C (0° F), or after the vehicle has not been driven in several days, let the engine warm up without operating the accelerator.
l Whether the engine is cold or warm,
it should be started without use of the accelerator.
Turning off the engine
1. Turn the ignition switch from the ON
position to the ACC position.
NOTE
When the engine is turned off and the ignition switch it turned from the ACC position to the LOCK position, the KEY indicator light (green) flashes in the instrument cluster for about 30
seconds if the battery power of the advanced key is low. Replace the battery with a new one. Refer to Battery Replacement (page 3-6).2. Push in the start knob from the ACC
position and turn it to the LOCK position.
NOTE
In the following cases, the KEY warning light (red) illuminates and the engine will not start. l The advanced key battery is dead. l The advanced key is out of
operational range.
l The advanced key is placed in areas where it is difficult for the system to detect the signal (page 3-7).
l A key from another manufacturer
similar to the advanced key is in the operational range.
8. Turn the ignition switch to the ACC position while pushing the start knob in.
9. Turn the ignition switch from the ACC
position to the START position and hold (up to 10 seconds at a time) until the engine starts.
3-12
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page81
Thursday, July 7 2005 1:2 PMBlack plate (81,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
CAUTION
When leaving the vehicle, make sure the ignition switch is turned to the LOCK position.
NOTE
l When turning the ignition switch to
the LOCK position, the ignition switch has to be pushed in from the ACC position and turned. Without being pushed in, the ignition switch stops at the ACC position and the vehicle battery may be discharged if the ignition switch is left in the ACC position. When leaving the vehicle, make sure the ignition switch is turned to the LOCK position.
l If the vehicle is left with the ignition switch not in the LOCK position, a beep sound is heard and the indicator light flashes to notify the driver. Refer to Warning Beep (page 3-16).
Operation Using Advanced Key Functions qKeyless Entry System This system remotely locks and unlocks the doors and the trunk lid, and opens the power windows. It can also help you signal for attention. Press the button slowly and carefully.
NOTE
l The keyless entry system is designed
to operate up to about 2.5 m (8 ft) from the center of the vehicle, but this may vary due to local conditions.
l The system does not operate when
the ignition switch is not in the LOCK position or the start knob is pushed in.
l With the start knob installed in the LOCK position, the system is fully operational. If the ignition switch is not in the LOCK position or the start knob is pushed in, the system does not operate.
l All doors and the trunk lid cannot be
locked by pressing the lock button while any door or the trunk lid is open. The hazard warning lights will also not flash.
l If the transmitter does not operate
when pressing a button or the operational range becomes too small, the battery may be dead. To install a new battery, refer to Maintenance (page 3-5).
3-13
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page82
Thursday, July 7 2005 1:2 PMBlack plate (82,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
The operation indicator light flashes when the buttons are pressed.
Lock button To lock the doors and the trunk lid, press the lock button. A beep sound will be heard once and the hazard warning lights will flash once.
To confirm that all doors and the trunk lid have been locked, press the lock button again within 5 seconds. If they are closed and locked, the horn will sound.
NOTE
l All doors and the trunk lid cannot be
locked when any door or the trunk lid is open.
l Confirm that all doors and the trunk lid are locked visually or audibly by use of the double click.
Unlock button To unlock the driver's door, press the unlock button. A beep will be heard twice and the hazard warning lights will flash twice.
To unlock all doors and the trunk lid, press the unlock button again within 5
seconds and two more beep sounds will be heard.NOTE
After unlocking with the transmitter, all doors and the trunk lid will automatically lock if one of the doors or the trunk lid is not opened within about 30 seconds.
Transmitter
Lock button
Unlock button
Panic button
NOTE
l (U.S.A.)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
l (CANADA)
This device complies with RSS-210
of Industry CANADA. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.NOTE
The unlock button can be used to open the power windows, but the lock button cannot be used to close the power windows. Refer to Opening/Closing Power Windows from Outside (page 3-39).
3-14
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page83
Thursday, July 7 2005 1:2 PMBlack plate (83,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Panic button If you witness from a distance someone attempting to break into or damage your vehicle, pressing the panic button will activate the vehicle's alarm.
NOTE
The panic button will work whether any door or the trunk lid is open or closed.
(Turning on the alarm) Pressing the panic button for 1 second or more will trigger the alarm for about 2
minutes and 30 seconds, and the following will occur: l The horn sounds intermittently. l The hazard warning lights flash.NOTE
However, if the driver is too close to the vehicle the panic button may not function.
(Turning off the alarm) The alarm stops by pressing any button on the transmitter.
qAuxiliary Key Function Use the auxiliary key stored in the advanced key in the event of a dead battery or malfunction.
Removing the auxiliary key Pull out the auxiliary key from the advanced key.
Locking, unlocking the doors The doors can be locked/unlocked using the auxiliary key, refer to Locking, Unlocking with Key (page 3-26).
Locking, unlocking the trunk lid The trunk lid can be locked/unlocked using the auxiliary key, refer to Locking, Unlocking with Key (page 3-29).
Starting the engine The engine can be started with the auxiliary key, refer to Starting the Engine (page 5-4).
3-15
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page84
Thursday, July 7 2005 1:2 PMBlack plate (84,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Warning and Beep Sounds qSystem Malfunction Warning Beep If any malfunction occurs in the advanced keyless function, the KEY warning light (red) in the instrument cluster illuminates continuously and beep sounds will be heard.
CAUTION
If the KEY warning light (red) remains illuminated, do not continue to drive the vehicle with the advanced keyless function. Park the vehicle in a safe place and use the auxiliary key to continue driving the vehicle. Have the vehicle inspected at an Authorized Mazda Dealer as soon as possible. Refer to Ignition Switch (page 5-2).
qStart Knob Not in LOCK
Warning Beep
If the start knob is in the ACC position and the driver's door is opened, a continuous beep sound will be heard to notify the driver that the start knob has not been returned to the LOCK position. In this case, the keyless entry system does not operate.
qAdvanced Key Removed from
Vehicle Warning Beep
Under the following conditions, a beep will be heard 3 times and the KEY warning light (red) will flash continuously when the start knob has not been returned to the LOCK position to notify the driver that the advanced key has been removed. The KEY warning light (red) will stop flashing when the advanced key is back inside the vehicle: l The start knob has not been returned to the LOCK position, the driver's door is open, and the advanced key is removed from the vehicle. However the beep will be heard continuously when the start knob is in the ACC position and the door is open due to the activation of the warning beep indicating that the start knob is not in the LOCK position.
l The start knob has not been returned to
the LOCK position and all the doors are closed after removing the advanced key from the vehicle.
NOTE
Because the advanced key utilizes low- intensity radio waves, the Advanced Key Removed From Vehicle Warning may activate if the advanced key is carried together with a metal object or it is placed in a poor signal reception area.
3-16
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page85
Thursday, July 7 2005 1:2 PMBlack plate (85,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
qEngine Start Not Permitted Warning Under the following conditions, the KEY warning light (red) flashes to inform the driver that the start knob will not rotate to the ACC position even if it is pushed in from the LOCK position. l The advanced key battery is dead. l The advanced key is not within
operational range.
l The advanced key is placed in areas where it is difficult for the system to detect the signal (page 3-7).
l A key from another manufacturer
similar to the advanced key is in the operational range.
qRequest Switch Inoperable
Warning Beep
Under the following conditions, if the request switch for a front door or the trunk lid is pressed while the advanced key is being carried, a beep will be heard 3 times to indicate that the front doors and the trunk lid cannot be locked. l There is a separate advanced key in the
vehicle.
l A door or the trunk lid is open (door
ajar included).
l The start knob has not been returned to
the LOCK position.
l The auxiliary key is inserted into the
ignition switch.
qAdvanced Key Battery Dead
Warning
When the start knob is returned to the ACC or LOCK position from the ON position, the KEY indicator light (green) flashes for approximately 30 seconds indicating that the remaining battery power is low. Replace with a new battery before the advanced key becomes unusable. Refer to Advanced Key Maintenance (page 3-5).
NOTE
The advanced key can be set so that the KEY indicator light (green) does not flash even if the battery power is low. Refer to Setting Change (page 3-18).
Form No.8U01-EA-05H
3-17
Mazdaspeed6_8U01-EA-05H_Edition1 Page86
Thursday, July 7 2005 1:2 PMBlack plate (86,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
Setting Change (Function Customization)
The following function settings are possible. Settings can be changed for each registered advanced key. These settings can only be changed by an Authorized Mazda Dealer.
Setting
Function
Advanced key battery dead indicator Lock/unlock operation confirmation beep sound*1
Autolock function
KEY indicator light (green) flashes to indicate that the advanced key battery power is low. A beep sound is heard to confirm that all doors or the trunk lid have been locked/unlocked. When all doors and the trunk lid are closed and the advanced key is being carried and out of operational range, all doors and the trunk lid automatically lock after 3 seconds. (Even if the driver is in the operational range, all doors and the trunk lid are locked automatically after about 30 seconds.)
At Initial Setting
After Setting
Change
Activated
Deactivated
Activated
Deactivated
Deactivated
Activated
*1 : When the autolock function is operating, the warning sound will be heard regardless of the setting.
3-18
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page87
Thursday, July 7 2005 1:2 PMBlack plate (87,1)
Knowing Your Mazda Advanced Keyless Entry and Start System
User Mis-Operation Warning Indicators
Under the following conditions, warning beeps are heard and a warning/indicator light in the instrument cluster illuminates to notify the driver of improper operation of the advanced key to prevent theft of the vehicle (page 3-16).
Warning condition
Check
When a door is open, a continuous beep sound will be heard. When a door is open, 3 beep sounds are heard, and the KEY warning light (red) in the instrument cluster flashes. When a door is closed, a beep sound is heard 3 times, and the KEY warning light (red) in the instrument cluster flashes.
When attempting to lock the doors, a beep sound is heard 3 times.
When the KEY indicator light (green) flashes in the instrument cluster.
When the KEY warning light (red) remains illuminated in the instrument cluster.
Check whether the start knob has been returned to the LOCK position.
Check whether the advanced key has been removed from the vehicle.
Check whether the advanced key has been removed from the vehicle.
Check whether the advanced key has been left in the vehicle. Check whether the start knob has been returned to the LOCK position. Check whether a door or the trunk lid is open. The advanced key battery power is low. Replace the battery with a new one. Refer to Advanced Key Maintenance on page 3-5. The advanced key is malfunctioning. Park the vehicle in a safe place, and use the auxiliary key to continue driving the vehicle. Have the vehicle inspected at an Authorized Mazda Dealer as soon as possible.
Form No.8U01-EA-05H
3-19
Mazdaspeed6_8U01-EA-05H_Edition1 Page88
Thursday, July 7 2005 1:2 PMBlack plate (88,1)
Knowing Your Mazda Doors and Locks
Keys
WARNING
Keys and Children: Leaving children in a vehicle with the key is dangerous. This could result in someone being badly injured or even killed. These new kinds of keys are fascinating to children. They could play with power windows or other controls, or even make the vehicle move. Don't leave the keys in your vehicle with children and keep them in a place where your children will not find or play with them.
NOTE
l If your vehicle is equipped with the
advanced key, refer to Advanced Keys (page 3-2).
l Refer to Immobilizer System (page
3-50) for information regarding keys and engine starting.
l Refer to Theft-Deterrent System
(page 3-53) for information regarding keys and the prevention of vehicle and vehicle contents theft.
3-20
Form No.8U01-EA-05H
Your Mazda has two kinds of keys.
Master key (Retractable type key)
Valet key
Key code number plate
Here's what the keys are used for:
Lock Operates
Master key Valet key
Ignition switch and steering column lock
Driver's door Glove box Trunk lid
Yes
Yes Yes Yes
Yes
Yes No No
If you must leave your vehicle with another person, such as a parking attendant, protect items by locking the glove box and trunk lid with the master key. Keep that key and give the other person only the valet key.
A code number is stamped on the plate attached to the key set; detach this plate and store it in a safe place (not in the vehicle) for use if you need to make a replacement key.
NOTE
Write down the code number and keep it in a separate safe and convenient place, but not in the vehicle. If your key is lost, consult your Authorized Mazda Dealer and have your code number ready.
Mazdaspeed6_8U01-EA-05H_Edition1 Page89
Thursday, July 7 2005 1:2 PMKey extend/retract method (Retractable type key) To extend the key, press the release button.
To retract the key, press the release button and rotate the key into the holder.
Black plate (89,1)
Knowing Your Mazda Doors and Locks
Keyless Entry System (with Retractable Type Key)
This system remotely locks and unlocks the doors and the trunk lid, and opens the power windows. It can also help you signal for attention. Press the button slowly and carefully.
CAUTION
To avoid damage to the transmitter, do not: l Drop it. l Get it wet. l Disassemble it. l Expose it to heat or sunlight.
Form No.8U01-EA-05H
3-21
Mazdaspeed6_8U01-EA-05H_Edition1 Page90
Thursday, July 7 2005 1:2 PMBlack plate (90,1)
Knowing Your Mazda Doors and Locks
NOTE
l The keyless entry system is designed
to operate up to about 2.5 m (8 ft) from the center of the vehicle, but this may vary due to local conditions.
l The system doesn't operate when the
key is in the ignition switch.
l Doors and the trunk lid cannot be locked by pressing the lock button while any other door or the trunk lid is open. Also, the hazard warning lights will not flash.
l If the transmitter does not operate
when pressing a button or the operation range becomes too small, the battery may be dead. To install a new battery, refer to Maintenance (page 3-23).
l Additional transmitters can be
obtained at an Authorized Mazda Dealer. Up to 3 transmitters can be used with the keyless entry system per vehicle. Bring all transmitters to an Authorized Mazda Dealer when the electronic codes need to be reset.
3-22
Form No.8U01-EA-05H
qTransmitter
Lock button
Unlock button
Operation indicator light
Panic button
NOTE
l (U.S.A.)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
l (CANADA)
This device complies with RSS-210
of Industry CANADA. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.NOTE
The unlock button can be used to open the power windows, but the lock button cannot be used to close the power windows. Refer to Opening/Closing Power Windows from Outside (page 3-39).
Black plate (91,1)
Knowing Your Mazda Doors and Locks
Panic button If you witness from a distance someone attempting to break into or damage your vehicle, pressing the panic button will activate the vehicle's alarm.
NOTE
The panic button will work whether any door or the trunk lid is open or closed.
Turning on the alarm Pressing the panic button for 1 second or more will trigger the alarm for about 2
minutes and 30 seconds, and the following will occur: l The horn sounds intermittently. l The hazard warning lights flash.Turning off the alarm Press any button on the transmitter.
qTransmitter Maintenance If the buttons on the transmitter are inoperable and the operation indicator light does not flash, the battery may be dead. Replace with a new battery before the transmitter becomes unusable.
Mazdaspeed6_8U01-EA-05H_Edition1 Page91
Thursday, July 7 2005 1:2 PMThe operation indicator light flashes when the buttons are pressed.
Lock button To lock the doors and the trunk lid, press the lock button and the hazard warning lights will flash once.
To confirm that all doors and the trunk lid have been locked, press the lock button again within 5 seconds. If they are closed and locked, the horn will sound.
NOTE
l All doors and the trunk lid cannot be
locked when any door or the trunk lid is open and the key is in the ignition switch.
l Confirm that all doors and the trunk lid are locked visually or audibly by use of the double click.
Unlock button To unlock the driver's door, press the unlock button and the hazard warning lights will flash twice.
To unlock all doors and the trunk lid, press the unlock button again within 5
seconds.NOTE
After unlocking with the transmitter, all doors and the trunk lid will automatically lock if one of the doors or the trunk lid is not opened within about 30 seconds.
Form No.8U01-EA-05H
3-23
Mazdaspeed6_8U01-EA-05H_Edition1 Page92
Thursday, July 7 2005 1:2 PMBlack plate (92,1)
Knowing Your Mazda Doors and Locks
CAUTION
l Install the battery with the positive
) facing down. Battery pole ( leakage could occur if it is not installed correctly.
l When replacing the battery, be
careful not to bend the electrical terminals or get oil on them. Also be careful not to get dirt in the transmitter as it could be damaged. l There is the danger of explosion if
the battery is not correctly replaced.
l Replace only with the same type battery (CR1620 or equivalent).
l Dispose of used batteries according
to the following instructions.
Insulate the plus and minus terminals of the battery using cellophane or equivalent tape.
l Never disassemble. l Never throw the battery into fire
and/or water.
l Never deform or crush.
Replacing the transmitter battery
1. Unfold the key (page 3-20).
2. Insert a small screwdriver into the slot
and push the tab to remove the key from the transmitter.
Tab
3. Insert a small screwdriver into the slot
and gently pry open the transmitter.
4. Press the portion of the battery
indicated by A and remove the battery.
3-24
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page93
Thursday, July 7 2005 1:2 PMBlack plate (93,1)
Knowing Your Mazda Doors and Locks
NOTE
If it is difficult to remove the battery by pressing with a finger, use a small screwdriver to press out the battery.
5. Put in the new battery (CR1620 or equivalent) with the positive pole ( facing down.
CAUTION
Radio equipment like this is governed by laws in the United States. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
6. Align the front and back covers and
snap the transmitter shut.
7. Install the key to the transmitter.
qService If you have a problem with the keyless entry system, consult an Authorized Mazda Dealer.
If your transmitter is lost or stolen, bring all remaining transmitters to an Authorized Mazda Dealer as soon as possible for a replacement and to make the lost or stolen transmitter inoperative.
Form No.8U01-EA-05H
3-25
Mazdaspeed6_8U01-EA-05H_Edition1 Page94
Thursday, July 7 2005 1:2 PMBlack plate (94,1)
Knowing Your Mazda Doors and Locks
Door Locks
WARNING
Unattended Children and Pets: Leaving a child or an animal unattended in a parked vehicle is dangerous. In hot weather, temperatures inside a vehicle can become high enough to cause brain damage or even death. Always take all children and animals with you or leave a responsible person with them.
Keys and Children: Leaving children in a vehicle with the key is dangerous. This could result in someone being badly injured or even killed. They could play with power windows or other controls, or even make the vehicle move. Don't leave the keys in your vehicle with children and keep them in a place where your children will not find or play with them.
Unlocked Doors: Unlocked doors in a moving vehicle are dangerous. Passengers can fall out if a door is accidentally opened and can more easily be thrown out in an accident. So keep all doors locked when driving.
3-26
Form No.8U01-EA-05H
WARNING
Vehicles Left Unlocked: Leaving your vehicle unlocked is dangerous as children could lock themselves in a hot vehicle, which could result in death. Also, a vehicle left unlocked becomes an easy target for thieves and intruders. Always close all the windows, lock the doors and take the key with you when leaving your vehicle unattended.
qLocking, Unlocking with Key The driver's door can be locked/unlocked with the key. Turn the key toward the front to unlock, toward the back to lock.
Unlock
Lock
qLocking, Unlocking with Request
Switch (with Advanced Key)
The doors can be locked/unlocked by operating the request switch while carrying the advanced key outside the vehicle, refer to Operations Using Advanced Keyless Functions (page 3-7).
Mazdaspeed6_8U01-EA-05H_Edition1 Page95
Thursday, July 7 2005 1:2 PMqLocking, Unlocking with
Transmitter (with Advanced Key)
The doors can be locked/unlocked by operating the keyless entry system transmitter, refer to Keyless Entry System (page 3-13).
qLocking, Unlocking with Transmitter
(with Retractable Type Key)
The doors can be locked/unlocked by operating the keyless entry system transmitter, refer to Keyless Entry System (page 3-21).
qLocking, Unlocking with Door-
Lock Knob
To lock any door from the inside, push the door-lock knob. To unlock, pull it out. This does not operate the other door locks.
Lock
Unlock
Form No.8U01-EA-05H
Black plate (95,1)
Knowing Your Mazda Doors and Locks
To lock any door with the door-lock knob from the outside, push the door-lock knob to the lock position and close the door. This does not operate the other door locks.
Door-lock knob
NOTE
When locking the doors this way, be careful not to leave the key inside the vehicle.
qPower Door Locks Vehicle lock-out prevention (With advanced key) The vehicle lock-out prevention feature prevents you from locking yourself out of the vehicle. All doors and the trunk lid will automatically unlock if they are locked using the power door locks with any door or the trunk lid open. (Without advanced key) The vehicle lock-out prevention feature prevents you from locking yourself out of the vehicle. With the key in the ignition switch, all doors and the trunk lid will automatically unlock if they are locked using the power door locks with any door or the trunk lid open.
3-27
Mazdaspeed6_8U01-EA-05H_Edition1 Page96
Thursday, July 7 2005 1:2 PMBlack plate (96,1)
Knowing Your Mazda Doors and Locks
Locking, unlocking with key All doors and the trunk lid lock automatically when the driver's door is locked with the key. All doors and the trunk lid unlock when the driver's door is unlocked and the key is held in the unlock position for one second or longer.
Locking, unlocking with door-lock switch All doors and the trunk lid lock automatically when LOCK is pushed. They all unlock when the unmarked part of the door-lock switch is pushed.
Unlock
Lock
Locking, unlocking with request switch (with advanced key) All doors and the trunk lid can be locked/ unlocked by operating the request switch while carrying the advanced key outside the vehicle, refer to Operations Using Advanced Keyless Functions (page 3-7).
Locking, unlocking with transmitter (with advanced key) All doors and the trunk lid can be locked/ unlocked by operating the keyless entry system transmitter, refer to Keyless Entry System (page 3-13).
Locking, unlocking with transmitter (with retractable type key) All doors and the trunk lid can be locked/ unlocked by operating the keyless entry system transmitter, refer to Keyless Entry System (page 3-21).
Unlock
NOTE
Lock
Holding the key in the unlocked position in the driver's door lock for about a second unlocks all doors and the trunk lid. To unlock only the driver's door, insert the key into the driver's door lock and turn the key briefly to the unlock position and then immediately return it to the center position.
3-28
Form No.8U01-EA-05H
Mazdaspeed6_8U01-EA-05H_Edition1 Page97
Thursday, July 7 2005 1:2 PMqRear Door Child Safety Locks These locks are intended to help prevent children from accidentally opening the rear doors. Use them both whenever a child rides in the vehicle.
If you slide the child safety lock to the lock position before closing that door, the door cannot be opened from the inside. The door can be opened only by pulling the outside handle.
Lock
Unlock
Form No.8U01-EA-05H
Black plate (97,1)
Knowing Your Mazda Doors and Locks
Trunk Lid
WARNING
Open Trunk and Exhaust Gas: Exhaust gas in the cabin of a vehicle is dangerous. This gas contains CO (carbon monoxide), which is colorless, odorless, and highly poisonous. If inhaled, it can cause loss of consciousness and death. Because exhaust gas can get into the cabin through an open trunk, keep the trunk closed when driving.
qLocking, Unlocking with Key To lock the trunk lid, insert the master key into the key slot and return it counterclockwise, then turn it to the center position and remove it.
Lock
Unlock
To unlock the trunk lid, insert the master key into the key slot and turn it clockwise, then return it to the center position and remove it.
The trunk lid can be locked/unlocked by inserting the key into the driver's door key slot, refer to Power Door Locks (page 3-27).
3-29
Mazdaspeed6_8U01-EA-05H_Edition1 Page98
Thursday, July 7 2005 1:2 PMBlack plate (98,1)
qOpening and Closing the Trunk
WARNING
Trunk Access and Children: Leaving the trunk lid open or leaving children in the vehicle with the keys is dangerous. Children could open the trunk lid and climb inside resulting in possible injury or death from heat exposure. Close the trunk lid, lock the rear seatbacks and do not allow children to play inside the vehicle.
Unattended Children and Pets: Leaving children or animals unattended in a parked vehicle is dangerous. Babies left sleeping and children who lock themselves in cars or trunks can die very quickly from heat prostration. Don't leave your children or pets alone in a car at any time. Don't leave the car, the rear folding seats or the trunk unlocked. Always keep the car from being a tempting place to play by locking rear seats, doors and the trunk, and keeping the keys where children can not play with them.
CAUTION
For vehicles equipped with a rear spoiler, do not lift the trunk lid by the spoiler. Lifting up the trunk lid by the rear spoiler could cause damage to the rear spoiler and the trunk lid.
Knowing Your Mazda Doors and Locks
qLocking, Unlocking with Request
Switch (with Advanced Key)
The trunk lid can be locked/unlocked by
