Download PDF Manual

are the correct size specified for your Mazda.


WARNING


Incorrect Tire Inflation: Overinflation or underinflation of tires is dangerous. Adverse handling or unexpected tire failure could result in a serious accident. Always inflate the tires to the correct pressure (page 10-5).


Refer to the specification charts (page 10-5).


8-26


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page279
Thursday, July 7 2005 1:4 PM


NOTE


l Always check tire pressure when


tires are cold.


l Warm tires normally exceed


recommended pressures. Don't release air from warm tires to adjust the pressure.


l Underinflation can cause reduced


fuel economy, uneven and accelerated tire wear, and poor sealing of the tire bead, which will deform the wheel and cause separation of tire from rim.


l Overinflation can produce a harsh


ride, uneven and accelerated tire wear, and a greater possibility of damage from road hazards. Keep your tire pressure at the correct levels. If one frequently needs inflating, have it inspected.


Form No.8U01-EA-05H


Black plate (279,1)


Maintenance and Care Owner Maintenance


qTire Rotation To equalize tread wear, rotate the tires every 12,000 km (7,500 miles)/8,000
km*(5,000 miles) or sooner if irregular wear develops. During rotation, inspect them for correct balance. * Unique driving conditions for U.S.A.,


Canada and Puerto Rico


Forward


Do not include (TEMPORARY USE ONLY) spare tire in rotation.


Also, inspect them for uneven wear and damage. Abnormal wear is usually caused by one or a combination of the following:


l Incorrect tire pressure l Improper wheel alignment l Out-of-balance wheel l Severe braking


After rotation, inflate all tire pressures to specification (page 10-5) and inspect the lug nuts for tightness.


CAUTION


Rotate unidirectional tires and radial tires that have an asymmetrical tread pattern or studs only from front to rear, not from side to side. Tire performance will be weakened if rotated from side to side.


8-27


Mazdaspeed6_8U01-EA-05H_Edition1 Page280
Thursday, July 7 2005 1:4 PM


Black plate (280,1)


Maintenance and Care Owner Maintenance


qReplacing a Tire


NOTE


Tires degrade over time, even when they are not being used on the road. It is recommended that tires generally be replaced when they are 6 years or older. Heat caused by hot climates or frequent high loading conditions can accelerate the aging process. You should replace the spare tire when you replace the other road tires due to the aging of the spare tire. Regarding the manufacturing week and year is indicated with 4 digit. Refer to The tire labeling on page 9-18.


qTemporary Spare Tire Inspect the temporary spare tire at least monthly to make sure it's properly inflated and stored.


NOTE


The temporary spare tire condition gradually deteriorates even if it has not been used.


The temporary spare tire is easier to handle because of its construction. It is lighter and smaller than a conventional tire and should be used only for an emergency and only for a short distance.


Use the temporary only until the conventional tire is repaired, which should be as soon as possible.


Maintain its pressure at 420 kPa (4.2
kgf/cm2 or bar, 60 psi).


WARNING


Worn Tires: Driving with worn tires is dangerous. Reduced braking, steering, and traction could result in an accident. Always use tires that are in good condition.


If a tire wears evenly, a wear indicator will appear as a solid band across the tread. Replace the tire when this happens.


Tread wear indicator


New tread


Worn tread


You should replace it before the band is across the entire tread.


8-28


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page281
Thursday, July 7 2005 1:4 PM


CAUTION


l Don't use your temporary spare tire


rim with a snow tire or a conventional tire. Neither will properly fit and could damage both tire and rim.


l The temporary spare tire has a tread


life of less than 5,000 km (3,000
miles). The tread life may be shorter depending on driving conditions.


l The temporary spare tire is for


limited use, however, if the tread wear solid-band indicator appears, replace the tire with the same type of temporary spare (page 8-28).


NOTE


Tires degrade over time, even when they are not being used on the road. It is recommended that tires generally be replaced when they are 6 years or older. Heat caused by hot climates or frequent high loading conditions can accelerate the aging process. You should replace the spare tire when you replace the other road tires due to the aging of the spare tire. Regarding the manufacturing week and year is indicated with 4 digit. Refer to The tire labeling on page 9-18.


Form No.8U01-EA-05H


Black plate (281,1)


Maintenance and Care Owner Maintenance


qReplacing a Wheel


WARNING


Using a Wrong-Sized Wheel: Using a wrong-sized wheel is dangerous. Braking and handling could be affected, leading to loss of control and an accident. Always use wheels of the correct size on your vehicle.


CAUTION


A wrong-sized wheel may adversely affect: l Tire fit l Wheel and bearing life l Ground clearance l Speedometer calibration l Headlight aim l Bumper height


When replacing a wheel, make sure the new one is the same as the original factory wheel in diameter, rim width, and offset.


Proper tire balancing provides the best riding comfort and helps reduce tread wear. Out-of-balance tires can cause vibration and uneven wear, such as cupping and flat spots.


8-29


Mazdaspeed6_8U01-EA-05H_Edition1 Page282
Thursday, July 7 2005 1:4 PM


Black plate (282,1)


Maintenance and Care Owner Maintenance


Light Bulbs


Overhead light/Map lights


Headlights (Low beam)


Parking lights


Headlights (High beam)


Fog lights


Trunk light


High-mount brake light


License plate lights


8-30


Side-marker lights


Front turn signal lights


Brake lights/Taillights


Courtesy lights


Rear turn signal lights Reverse lights Taillights


The equipment and installation position varies according to model and grade.


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page283
Thursday, July 7 2005 1:4 PM


WARNING


Xenon Fusion Bulb Replacement: Replacing the xenon fusion bulbs yourself is dangerous. Because the xenon fusion bulbs require high voltage, you could receive an electric shock if the bulbs are handled incorrectly. Do not replace the xenon fusion bulbs yourself. Consult an Authorized Mazda Dealer when the replacement is necessary.


Handling Halogen Bulbs: When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass. If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit. Never touch the glass portion of the bulb with your bare hands and always wear eye protection when handling or working around halogen bulbs.


Children and Halogen Bulbs: Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way. Always keep halogen bulbs out of the reach of children.


qReplacing Exterior Light Bulbs Replacing the headlight, fog light and parking light bulbs Due to the complexity and difficulty of the procedure, the bulbs should be replaced by an Authorized Mazda Dealer.


Form No.8U01-EA-05H


Black plate (283,1)


Maintenance and Care Owner Maintenance


Front turn signal lights


1. Turn the socket and bulb assembly


counterclockwise and remove it.


2. Remove the bulb by pushing it in


slightly and turning it counterclockwise.


3. Install the new bulb in the reverse order


of removal.


Side-marker lights


1. If you are changing the left side-maker light, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the right side-maker light, turn the steering wheel to the left.


2. Turn the screws counterclockwise and


remove them.


8-31


Mazdaspeed6_8U01-EA-05H_Edition1 Page284
Thursday, July 7 2005 1:4 PM


Black plate (284,1)


Maintenance and Care Owner Maintenance


3. Turn the center section of the plastic


retainers counterclockwise and remove them, and partially peel back the mudguard.


Removal


Installation


4. Turn the socket and bulb assembly


counterclockwise and remove it.


5. Disconnect the bulb from the socket.


Brake lights/Taillights, Rear turn signal lights


1. Pull the center section of the plastic


retainer and remove the retainers and partially open the trunk side trim.


Removal


Installation


2. Turn the socket and bulb assembly


counterclockwise and remove it.


3. Disconnect the bulb from the socket.


Brake lights/Taillights


8-32


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page285
Thursday, July 7 2005 1:4 PM


Black plate (285,1)


Maintenance and Care Owner Maintenance


Rear turn signal lights


3. Disconnect the bulb from the socket.


Reverse lights Taillights


4. Install the new bulb in the reverse order


4. Install the new bulb in the reverse order


of removal.


NOTE


To replace the bulb, contact an Authorized Mazda Dealer.


Reverse lights, Taillights


1. Pull the center section of the plastic


retainer and remove the retainers, then remove the trunk rear trim.


of removal.


License plate lights


1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens by carefully prying on the edge of the lens.


2. Disconnect the bulb by pulling it out.


Removal


Installation


2. Turn the socket and bulb assembly


counterclockwise and remove it.


3. Install the new bulb in the reverse order


of removal.


Form No.8U01-EA-05H


8-33


Mazdaspeed6_8U01-EA-05H_Edition1 Page286
Thursday, July 7 2005 1:4 PM


Black plate (286,1)


Maintenance and Care Owner Maintenance


qReplacing Interior Light Bulbs Overhead light/Map lights (Front)


1. Remove the screws.


2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the trim and gently insert it in the overhead light as shown in the figure, and then remove the overhead light unit.


Overhead light/Map lights (Rear)


1. Wrap a flathead screwdriver with a soft cloth to prevent damage to the trim and gently insert it in the overhead light as shown in the figure, and then remove the overhead light unit.


2. Turn the socket and bulb assembly


counterclockwise and remove it.


3. Disconnect the bulb from the socket.


3. Turn the socket and bulb assembly


counterclockwise and remove it.


4. Disconnect the bulb from the socket.


4. Install the new bulb in the reverse order


of removal.


5. Install the new bulb in the reverse order


of removal.


8-34


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page287
Thursday, July 7 2005 1:4 PM


Black plate (287,1)


Maintenance and Care Owner Maintenance


Courtesy lights, Vanity mirror lights


Trunk light


1. Wrap a small flathead screwdriver with


1. Press both sides of the lens cap to


a soft cloth to prevent damage to the lens and remove the lens by carefully prying on the edge of the lens.


2. Disconnect the bulb by pulling it out.


remove it.


2. Disconnect the bulb by pulling it out.


Courtesy lights


Edge


Vanity mirror lights


3. Install the new bulb in the reverse order


of removal.


3. Install the new bulb in the reverse order


of removal.


Edge


Form No.8U01-EA-05H


8-35


Mazdaspeed6_8U01-EA-05H_Edition1 Page288
Thursday, July 7 2005 1:4 PM


Black plate (288,1)


Maintenance and Care Owner Maintenance


Fuses


Your vehicle's electrical system is protected by fuses.


If any lights, accessories, or controls don't work, inspect the appropriate circuit protector. If a fuse has blown, the inside element will be melted.


If the same fuse blows again, avoid using that system and consult an Authorized Mazda Dealer as soon as possible.


qFuse Replacement Replacing the fuses on the driver's side kick-panel If the electrical system doesn't work, first inspect fuses on the driver's side kick- panel.


1. Turn off the ignition switch and other


switches.


2. Open the fuse panel cover by sliding


the cover straight back toward you.


CAUTION


Pulling the cover off sideways may break the retaining tabs off.


8-36


Form No.8U01-EA-05H


3. Pull the fuse straight out with the fuse


puller provided on the fuse block located in the engine compartment.


4. Inspect it and replace if it's blown.


Normal


Blown


5. Push in a new fuse of the same


amperage rating, and make sure it fits tightly. If it doesn't, have an Authorized Mazda Dealer install it. If you have no spare fuses, borrow one of the same rating from a circuit not essential to vehicle operation, such as the AUDIO or CIGAR circuit.


WARNING


Always replace a fuse with one of the same rating. Otherwise you may damage the electric system.


Mazdaspeed6_8U01-EA-05H_Edition1 Page289
Thursday, July 7 2005 1:4 PM


Replacing the fuses under the hood If the headlights or other electrical components don't work and the fuses in the cabin are OK, inspect the fuse block under the hood. If a fuse is blown, it must be replaced. Follow these steps:


1. Turn off the ignition switch and all


other switches.


2. Remove the fuse block cover.


3. If a fuse is blown, replace it with a new


one of the same amperage rating.


Normal


Blown


NOTE


To replace the MAIN fuse, contact an Authorized Mazda Dealer (page 8-38).


Form No.8U01-EA-05H


Black plate (289,1)


Maintenance and Care Owner Maintenance


8-37


Mazdaspeed6_8U01-EA-05H_Edition1 Page290
Thursday, July 7 2005 1:4 PM


Black plate (290,1)


Maintenance and Care Owner Maintenance


qFuse Panel Description Fuse block (Engine compartment)


DESCRIPTION


FUSE


RATING


PROTECTED COMPONENT


10
11
12
13
14
15
16
17


SPARE SPARE SPARE M DEF



INJ


ENG BAR ENG BB HEAD LR HEAD LL HEAD HL HEAD HR


DRL


HAZARD


STOP ENG+B


ETC


8-38


íSome models.


20A 15A 10A 7.5A ―


15A 15A 5A 15A 15A 10A 10A 15A 10A 20A 10A 10A


Mirror defrosterí






PCM O2 Sensor, EGR control valve Waste gate solenoid, Cooling fan Headlight-low beam (Right) Headlight-low beam (Left) Headlight-high beam (Left) Headlight-high beam (Right) DRLí (Headlight high beams) Turn signal lights Brake lights, Horn PCM, AWD Electronic throttle


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page291
Thursday, July 7 2005 1:4 PM


Black plate (291,1)


Maintenance and Care Owner Maintenance


DESCRIPTION


FUSE


RATING


18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40



IG KEY 1
P.WIND


FUEL PUMP INJ DRIVE



BLOWER


BTN


IG KEY 2
DEFOG


ABS FAN2
FAN1
TAIL


ILLUMI


MAG AUDIO P.SEAT




H/CLEAN


FOG MAIN



30A 30A 30A 30A ―


40A 40A 40A 40A 60A 30A 30A 10A 10A 10A 15A 30A ―



20A 15A 120A


PROTECTED COMPONENT



Engine control, SAS, Instrument cluster, Lighter Power windows Fuel pump Injector



Blower motor Overhead light, Power door lock Wiper and washer, Climate control unit Rear window defroster DSC Cooling fan Cooling fan Taillights, License plate lights Dashboard illumination Magnet clutch Audio system Power seatí





Fog lights For protection of all circuits


íSome models.


8-39


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page292
Thursday, July 7 2005 1:4 PM


Black plate (292,1)


Maintenance and Care Owner Maintenance


Fuse block (Driver's side kick-panel)


DESCRIPTION


FUSE


RATING


PROTECTED COMPONENT


10
11
12
13
14
15
16
17
18


P.WIND IG


P.WIND D.LOCK CIGAR MIRROR


METER ACC


R.CIGAR SPARE


ENGINE IG


SAS


METER IG


WIPER SPARE


A/C SEAT R.WIP ROOM SPARE


8-40


íSome models.


30A 20A 30A 15A 5A 5A 15A 10A 15A 10A 15A 20A 15A 10A 15A 10A 15A 20A




Power door lock Lighter Power control mirror, Audio system Auto light off unit Accessory socket



Engine control system DSC unit, SAS unit Instrument cluster, Reverse lights Windshield wiper and washer



Heater Seat warmerí, Rear window defroster


Overhead light




Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page293
Thursday, July 7 2005 1:4 PM


How to Minimize Environmental Paint Damage


The paintwork on your Mazda represents the latest technical developments in composition and methods of application.


Environmental hazards, however, can harm the paint's protective properties, if proper care is not taken.


Here are some examples of possible damage, with tips on how to prevent them.


qEtching Caused by Acid Rain or


Industrial Fallout


Occurrence Industrial pollutants and vehicle emissions drift into the air and mix with rain or dew to form acids. These acids can settle on a vehicle's finish. As the water evaporates, the acid becomes concentrated and can damage the finish. And the longer the acid remains on the surface, the greater the chance is for damage.


Prevention It is necessary to wash and wax your vehicle to preserve its finish according to the instructions in this section. These steps should be taken immediately after you suspect that acid rain has settled on your vehicle's finish.


Form No.8U01-EA-05H


Black plate (293,1)


Maintenance and Care Appearance Care


qDamage Caused by Bird


Dropping, Insects, or Tree Sap


Occurrence Bird droppings contain acids. If these aren't removed they can eat away the clear and color base coat of the vehicle's paintwork.


When insects stick to the paint surface and decompose, corrosive compounds form. These can erode the clear and color base coat of the vehicle's paintwork if they are not removed.


Tree sap will harden and adhere permanently to the paint finish. If you scratch the sap off while it is hard, some vehicle paint could come off with it.


Prevention It is necessary to have your Mazda washed and waxed to preserve its finish according to the instructions in this section. This should be done as soon as possible.


Bird droppings can be removed with a soft sponge and water. If you are traveling and these are not available, a moistened tissue may also take care of the problem. The cleaned area should be waxed according to the instructions in this section. Insects and tree sap are best removed with a soft sponge and water or a commercially available chemical cleaner.


Another method is to cover the affected area with dampened newspaper for one to two hours. After removing the newspaper, rinse off the loosened debris with water.


8-41


Mazdaspeed6_8U01-EA-05H_Edition1 Page294
Thursday, July 7 2005 1:4 PM


Black plate (294,1)


NOTE


l The paint chipping zone varies with


the speed of the vehicle. For example, when traveling at 90 km/h (56 mph), the paint chipping zone is 50 m (164 ft).


l In low temperatures a vehicle's finish hardens. This increases the chance of paint chipping.


l Chipped paint can lead to rust


forming on your Mazda. Before this happens, repair the damage by using Mazda touch-up paint according to the instructions in this section. Failure to repair the affected area could lead to serious rusting and expensive repairs.


Maintenance and Care Appearance Care


qWater Marks Occurrence Rain, fog, dew, and even tap water can contain harmful minerals such as salt and lime. If moisture containing these minerals settles on the vehicle and evaporates, the minerals will concentrate and harden to form white rings. The rings can damage your vehicle's finish.


Prevention It is necessary to wash and wax your vehicle to preserve its finish according to the instructions in this section. These steps should be taken immediately after you find water marks on your vehicle's finish.


qPaint Chipping Occurrence Paint chipping occurs when gravel thrown in the air by another vehicle's tires hits your vehicle.


How to avoid paint chipping Keeping a safe distance between you and the vehicle ahead reduces the chances of having your paint chipped by flying gravel.


8-42


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page295
Thursday, July 7 2005 1:4 PM


Exterior Care


Follow all label and container directions when using a chemical cleaner or polish. Read all warnings and cautions.


qMaintaining the Finish Washing To help protect the finish from rust and deterioration, wash your Mazda thoroughly and frequently, at least once a month, with lukewarm or cold water.


If the vehicle is washed improperly, the paint surface could be scratched. Here are some examples of how scratching could occur.


Scratches occur on the paint surface when: l The vehicle is washed without first


rinsing off dirt and other foreign matter.


l The vehicle is washed with a rough,


dry, or dirty cloth.


l The vehicle is washed at a car wash that uses brushes that are dirty or too stiff.


l Cleansers or wax containing abrasives


are used.


NOTE


l Mazda is not responsible for


scratches caused by automatic car washes or improper washing.


l Scratches are more noticeable on


vehicles with darker paint finishes.


Form No.8U01-EA-05H


Black plate (295,1)


Maintenance and Care Appearance Care


To minimize scratches on the vehicle's paint finish: l Rinse off any dirt or other foreign


matter using lukewarm or cold water before washing.


l Use plenty of lukewarm or cold water


and a soft cloth when washing the vehicle. Do not use a nylon cloth.


l Rub gently when washing or drying the


vehicle.


l Take your vehicle only to a car wash


that keeps its brushes well maintained.


l Don't use abrasive cleansers or wax


that contain abrasives.


CAUTION


l Don't use steel wool, abrasive cleaners, or strong detergents containing highly alkaline or caustic agents on chrome-plated or anodized aluminum parts. This may damage the protective coating; also, cleaners and detergents may discolor or deteriorate the paint.


l To prevent damaging the antenna,


remove it before entering a car wash facility or passing beneath a low overhead clearance.


Pay special attention to removing salt, dirt, mud, and other foreign material from the underside of the fenders, and make sure the drain holes in the lower edges of the doors and rocker panels are clean.


8-43


Mazdaspeed6_8U01-EA-05H_Edition1 Page296
Thursday, July 7 2005 1:4 PM


Black plate (296,1)


Maintenance and Care Appearance Care


Insects, tar, tree sap, bird droppings, industrial fallout, and similar deposits can damage the finish if not removed immediately. When prompt washing with plain water is ineffective, use a mild soap made for use on vehicles.


Thoroughly rinse off all soap with lukewarm or cold water. Don't allow soap to dry on the finish.


After washing the vehicle, dry it with a clean chamois to prevent water spots from forming.


WARNING


Driving with Wet Brakes: Driving with wet brakes is dangerous. Increased stopping distance or the vehicle pulling to one side when braking could result in a serious accident. Light braking will indicate whether the brakes have been affected. Dry the brakes by driving very slowly and applying the brakes lightly until brake performance is normal.


Waxing Your vehicle needs to be waxed when water no longer beads on the finish. Always wash and dry the vehicle before waxing it. In addition to the vehicle body, wax the metal trim to maintain its luster.


1. Use wax which contains no abrasives. Waxes containing abrasive will remove paint and could damage bright metal parts.


2. Use a good grade of natural wax for


metallic, mica, and solid colors.


8-44


Form No.8U01-EA-05H


3. When waxing, coat evenly with the


sponge supplied or a soft cloth.


4. Wipe off the wax with a soft cloth.


NOTE


A spot remover to remove oil, tar, and similar materials will usually also take off the wax. Rewax these areas even if the rest of the vehicle doesn't need it.


qRepairing Damage to the Finish Deep scratches or chips on the finish should be repaired promptly. Exposed metal quickly rusts and can lead to major repairs.


CAUTION


If your Mazda is damaged and needs metal parts repaired or replaced, make sure the body shop applies anti- corrosion materials to all parts, both repaired and new. This will prevent them from rusting.


qBright-Metal Maintenance l Use tar remover to remove road tar and


insects. Never do this with a knife or similar tool.


l To prevent corrosion on bright-metal


surfaces, apply wax or chrome preservative and rub it to a high luster. l During cold weather or in coastal areas, cover bright-metal parts with a coating of wax or preservative heavier than usual. It would also help to coat them with noncorrosive petroleum jelly or some other protective compound.


Mazdaspeed6_8U01-EA-05H_Edition1 Page297
Thursday, July 7 2005 1:4 PM


CAUTION


Don't use steel wool, abrasive cleaners, or strong detergents containing highly alkaline or caustic agents on chrome- plated or anodized aluminum parts. This may result in damage to the protective coating and cause discoloration or paint deterioration.


qUnderbody Maintenance Road chemicals and salt used for ice and snow removal and solvents used for dust control may collect on the underbody. If not removed, they will speed up rusting and deterioration of such underbody parts as fuel lines, frame, floor pan, and exhaust system, even though these parts may be coated with anti-corrosive material.


Thoroughly flush the underbody and wheel housings with lukewarm or cold water at the end of each winter. Try also to do this every month.


Pay special attention to these areas because they easily hide mud and dirt. It will do more harm than good to wet down the road grime without removing it.


The lower edges of doors, rocker panels, and frame members have drain holes that should not be clogged. Water trapped there will cause rusting.


Form No.8U01-EA-05H


Black plate (297,1)


Maintenance and Care Appearance Care


WARNING


Driving with Wet Brakes: Driving with wet brakes is dangerous. Increased stopping distance or the vehicle pulling to one side when braking could result in a serious accident. Light braking will indicate whether the brakes have been affected. Dry the brakes by driving very slowly and applying the brakes lightly until brake performance is normal.


qAluminum Wheel Maintenance A protective coating is provided over the aluminum wheels. Special care is needed to protect this coating.


NOTE


l Don't use a wire brush or any


abrasive cleaner, polishing compound, or solvent on aluminum wheels. They may damage the coating.


l Only use a mild soap or neutral


detergent and always use a sponge or soft cloth to clean the wheels. Rinse thoroughly with lukewarm or cold water. Also, be sure to clean the wheels after driving on dusty or salted roads. This helps prevent corrosion.


l Avoid washing your vehicle in an automatic car wash that uses high- speed or hard brushes.


l If your aluminum wheels lose luster,


wax the wheels.


8-45


Mazdaspeed6_8U01-EA-05H_Edition1 Page298
Thursday, July 7 2005 1:4 PM


Black plate (298,1)


To keep the fabric looking clean and fresh, take care of it. Otherwise its color will be affected, it can be stained easily, and its fire-resistance may be reduced.


CAUTION


Use only recommended cleaners and procedures. Others may affect appearance and fire-resistance.


qCleaning the Lap/Shoulder Belt


Webbing


Clean the webbing with a mild soap solution recommended for upholstery or carpets. Follow instructions. Don't bleach or dye the webbing; this may weaken it.


After cleaning the belts, thoroughly dry the belt webbing and make sure there is no remaining moisture before retracting them.


WARNING


Damaged Seat Belt: Using damaged seat belts is dangerous. In a collision, damaged belts cannot provide adequate protection. Have an Authorized Mazda Dealer replace damaged belts immediately.


Maintenance and Care Appearance Care


Interior Care qDashboard Precautions Prevent caustic solutions such as perfume and cosmetic oils from contacting the dashboard. They'll damage and discolor it. If these solutions get on the dashboard, wipe them off immediately.


CAUTION


Do not use glazing agents. Glazing agents contain ingredients which may cause discoloration, wrinkling, cracks and peeling.


qCleaning the Upholstery and


Interior Trim


Vinyl Remove dust and loose dirt from vinyl with a whisk broom or vacuum cleaner. Clean vinyl with a leather-and-vinyl cleaner. Leatherí Real leather isn't uniform and may have scars, scratches, and wrinkles. Clean it with a leather cleaner or mild soap.


Wipe it with a damp soft cloth; then dry and buff it with a dry soft cloth. Fabricí Remove dust and loose dirt from fabric with a whisk broom or vacuum cleaner. Clean it with a mild soap solution good for upholstery and carpets. Remove fresh spots immediately with a fabric spot cleaner.


8-46


íSome models.


Form No.8U01-EA-05H


Black plate (299,1)


Maintenance and Care Appearance Care


Mazdaspeed6_8U01-EA-05H_Edition1 Page299
Thursday, July 7 2005 1:4 PM


qCleaning the Window Interiors If the windows become covered with an oily, greasy, or waxy film, clean them with glass cleaner. Follow the directions on the container.


CAUTION


Don't scrape or scratch the inside of the rear window. You may damage the rear window defroster grid.


Form No.8U01-EA-05H


8-47


Mazdaspeed6_8U01-EA-05H_Edition1 Page300
Thursday, July 7 2005 1:4 PM


Black plate (300,1)


8-48


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page301
Thursday, July 7 2005 1:4 PM


Black plate (301,1)


9 Customer Information and Reporting


Safety Defects


Important consumer information including warranties and add-on equipment.


Customer Assistance ............................... 9-2
Customer Assistance (U.S.A.) ............ 9-2
Customer Assistance (Canada) ........... 9-4
Customer Assistance (Puerto Rico) .... 9-7


Mazda Importer/Distributors ................. 9-8
Importer/Distributor ............................ 9-8
Distributor in Each Area ..................... 9-8


Warranty .................................................. 9-9
Warranties for Your Mazda ................. 9-9
Outside the United States .................. 9-10
Outside Canada ................................. 9-11
Registering Your Vehicle in A Foreign Country (Except United States and Canada) ............................................. 9-12
Add-On Non-Genuine Parts and Accessories ....................................... 9-13


Cell Phones ............................................. 9-14
Cell Phones Warning ......................... 9-14


Type Approval of Equipment ............... 9-15
Type Approval of Equipment ............ 9-15


Uniform Tire Quality Grading System (UTQGS) ................................................ 9-16


Uniform Tire Quality Grading System (UTQGS) .......................................... 9-16


Tire Information (U.S.A.) ..................... 9-18
Tire Labeling ..................................... 9-18
Location of the Tire Label (Placard) ............................................ 9-24
Tire Maintenance .............................. 9-27
Vehicle Loading ................................ 9-30
Steps for Determining the Correct Load Limit: ................................................ 9-37


Form No.8U01-EA-05H


Reporting Safety Defects ....................... 9-38
Reporting Safety Defects (U.S.A.) .... 9-38
Reporting Safety Defects (Canada) ... 9-39


Service Publications .............................. 9-40
Service Publications .......................... 9-40


9-1


Mazdaspeed6_8U01-EA-05H_Edition1 Page302
Thursday, July 7 2005 1:4 PM


Black plate (302,1)


Customer Information and Reporting Safety Defects Customer Assistance


Customer Assistance (U.S.A.)


Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps:


qSTEP 1: Contact Your Mazda Dealer Discuss the matter with an Authorized Mazda Dealer. This is the quickest and best way to address the issue. If your concern has not been resolved by the CUSTOMER RELATIONS, SALES, SERVICE, or PARTS MANAGER, then please contact the GENERAL MANAGER of the dealership or the OWNER.


qSTEP 2: Contact Mazda North American Operations If for any reason you feel the need for further assistance after contacting your dealership management, you can reach Mazda North American Operations by one of the following ways.


Log on: at www.mazdaUSA.com


Answers to many questions, including how to locate or contact a local Mazda dealership in the U.S., can be found here.


E-mail: click on “Contact Us” at the bottom of the page at www.mazdaUSA.com


By phone at: 1 (800) 222-5500


By letter at: Attn: Customer Assistance Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618-2922
P.O. Box 19734
Irvine, CA 92623-9734


In order to serve you efficiently and effectively, please help us by providing the following information:


1. Your name, address, and telephone number


2. Year and model of vehicle


9-2


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page303
Thursday, July 7 2005 1:4 PM


Black plate (303,1)


Customer Information and Reporting Safety Defects Customer Assistance


3. Vehicle Identification Number (17 digits, noted on your registration or title or located on


the upper driver's side corner of the dash)


4. Purchase date and current mileage


5. Your dealer's name and location


6. Your question(s)


If you live outside the U.S.A., please contact your nearest Mazda Distributor.


Form No.8U01-EA-05H


9-3


Mazdaspeed6_8U01-EA-05H_Edition1 Page304
Thursday, July 7 2005 1:4 PM


Black plate (304,1)


Customer Information and Reporting Safety Defects Customer Assistance


Customer Assistance (Canada)


qSatisfaction Review Process Your complete and permanent satisfaction is of primary concern to Mazda. All Authorized Mazda Dealers have both the knowledge and tools to keep your Mazda in top condition. In our experience, any questions, problems, or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer. If the cause of your dissatisfaction cannot adequately be addressed by normal dealership procedures, we recommend that you take the following steps:


qSTEP 1: Contact the Mazda Dealer Discuss the matter with a member of dealership management. If the Service Manager has already reviewed your concerns, contact the owner of the dealership or its General Manager.


qSTEP 2: Contact the Mazda Regional Office If you feel that you still require assistance, ask the dealer Service Manager to arrange for you to meet the local Mazda Service Representative. If more expedient, contact Mazda Canada Inc.Regional Office nearest you for such arrangements. Regional Office address and phone numbers are shown (page 9-6).


qSTEP 3: Contact the Mazda Customer Relations Department If still not substantially satisfied, contact the Customer Relations Department, Mazda Canada Inc., 55 Vogell Road, Richmond Hill, Ontario, L4B 3K5 Canada TEL: 1 (800) 263-4680. Provide the Department with the following information:


1. Your name, address and telephone number


2. Year and model of vehicle


3. Vehicle Identification Number (VIN). Refer to the “Vehicle Identification Labels” page


of section 10 of this manual for the location of the VIN.


4. Purchase date


5. Present odometer reading


6. Your dealer's name and location


7. The nature of your problem and/or cause of dissatisfaction


The Department, in cooperation with the local Mazda Service Representative, will review the case to determine if everything possible has been done to ensure your satisfaction.


9-4


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page305
Thursday, July 7 2005 1:4 PM


Black plate (305,1)


Customer Information and Reporting Safety Defects Customer Assistance


Please recognize that the resolution of service problems in most cases requires the use of your Mazda dealer's service facilities, personnel and equipment. We urge you to follow the above three steps in sequence for most effective results.


qMediation/Arbitration Program Occasionally a customer concern cannot be resolved through Mazda's Customer Satisfaction Program. If after exhausting the procedures in this manual your concern is still not resolved, you have another option.


Mazda Canada Inc. participates in an arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). CAMVAP will advise you about how your concern may be reviewed and resolved by an independent third party through binding arbitration.


Your complete satisfaction is the goal of Mazda Canada Inc. and our dealers. Mazda's participation in CAMVAP makes a valuable contribution to our achieving that goal. There is no charge for using CAMVAP. CAMVAP results are fast, fair and final as the award is binding on both you and Mazda Canada Inc.


qCanadian Motor Vehicle Arbitration Plan (CAMVAP) If a specific item of concern arises, where a solution cannot be reached between an owner, Mazda, and/or one of it's dealers (that all parties cannot agree upon), the owner may wish to use the services offered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).


CAMVAP uses the services of Provincial Administrators to assist consumers in scheduling and preparing for their arbitration hearings. However, before you can proceed with CAMVAP you must follow your Mazda dispute resolution process as outlined previously.


Form No.8U01-EA-05H


9-5


Mazdaspeed6_8U01-EA-05H_Edition1 Page306
Thursday, July 7 2005 1:4 PM


Black plate (306,1)


Customer Information and Reporting Safety Defects Customer Assistance


CAMVAP is fully implemented in all provinces and territories. Consumers wishing to obtain further information about the Program should contact the Provincial Administrator at 1 (800) 207-0685, or by contacting the Canadian Motor Vehicle Arbitration Plan Office at:


Canadian Motor Vehicle Arbitration Plan 235 Yorkland Boulevard, suite 300
North York, Ontario M2J 4Y8
http://camvap.ca Provincial Administrators may be reached locally as listed below:


Province/Territory


British Columbia & Yukon Territories


Alberta & Northwest Territories


Saskatchewan


Manitoba Ontario


Atlantic Canada


Quebec


qRegional Offices


REGIONAL OFFICES MAZDA CANADA INC.


WESTERN REGION


8171 ACKROYD ROAD


SUITE 2000


RICHMOND B.C.


V6X 3K1


(604) 303-5670


MAZDA CANADA INC.


CENTRAL/ATLANTIC REGION


55 VOGELL ROAD, RICHMOND HILL, ONTARIO, L4B 3K5


(905) 787-7000


MAZDA CANADA INC.


QUEBEC REGION 6111 ROUTE TRANS


CANADIENNE


POINTE CLAIRE, QUEBEC


H9R 5A5


(514) 694-6390


9-6


Form No.8U01-EA-05H


CAMVAP Number 1 (800) 207-0685
1 (800) 207-0685
1 (800) 207-0685
1 (800) 207-0685
1 (800) 207-0685
1 (800) 207-0685
1 (800) 207-0685


AREAS COVERED


ALBERTA,


BRITISH COLUMBIA,


MANITOBA,


SASKATCHEWAN,


YUKON


ONTARIO


QUEBEC,


NEW BRUNSWICK,


NOVA SCOTIA,


PRINCE EDWARD ISLAND,


NEWFOUNDLAND


Mazdaspeed6_8U01-EA-05H_Edition1 Page307
Thursday, July 7 2005 1:4 PM


Black plate (307,1)


Customer Information and Reporting Safety Defects Customer Assistance


Customer Assistance (Puerto Rico)


Your complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps:


qSTEP 1
Discuss the matter with an Authorized Mazda Dealer. This is the quickest and best way to address the issue. If your concern has not been resolved by the CUSTOMER RELATIONS, SALES, SERVICE, or PARTS MANAGER, then please contact the GENERAL MANAGER of the dealership or the OWNER.


qSTEP 2
If, after following STEP 1, you feel the need for further assistance, please contact your area's Mazda representative (Indicated on the next page).


Please help us by providing the following information:


1. Your name, address, and telephone number


2. Year and model of vehicle


3. Vehicle Identification Number (17 digits, noted on your registration or title or located on


the upper driver's side corner of the dash)


4. Purchase date and current mileage


5. Your dealer's name and location


6. Your question(s)


Form No.8U01-EA-05H


9-7


Mazdaspeed6_8U01-EA-05H_Edition1 Page308
Thursday, July 7 2005 1:4 PM


Black plate (308,1)


Customer Information and Reporting Safety Defects Mazda Importer/Distributors


Importer/Distributor


Distributor in Each Area


qCANADA Mazda Canada Inc. 55 Vogell Road, Richmond Hill, Ontario, L4B 3K5 Canada TEL: 1 (800) 263-4680 (in Canada) (905) 787-7000 (outside Canada)


qPUERTO RICO/U.S. Virgin Island Plaza Motors Corp. (Mazda de Puerto Rico) P.O. Box 362722, San Juan, Puerto Rico 00936-2722
TEL: (787) 641-9300


qGUAM Triple J Motors 157 South Marine Drive, Tamuning, GUAM 96911 USA P.O. Box 6066 Tamuning, Guam 96931
TEL: (671) 649-6555


qSAIPAN Pacific International Marianas, Inc. (d.b.a. Midway Motors) P.O. Box 887 Saipan, MP 96950
TEL: (670) 234-7524


Triple J Saipan, Inc. (d.b.a. Triple J Motors) P.O. Box 500487 Saipan, MP 96950-0487
TEL: (670) 234-7133/3051


qAMERICAN SAMOA Polynesia Motors, Inc. P.O. Box 1120, Pago Pago, American Samoa 96799
TEL: (684) 699-9347


qU.S.A. Mazda North American Operations 7755 Irvine Center Drive Irvine, CA 92618-2922 U.S.A. P.O. Box 19734
Irvine, CA 92623-9734 U.S.A. TEL: 1 (800) 222-5500 (in U.S.A.) (949) 727-1990 (outside U.S.A.)


9-8


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page309
Thursday, July 7 2005 1:4 PM


Black plate (309,1)


Customer Information and Reporting Safety Defects Warranty


Warranties for Your Mazda


l New Vehicle Limited Warranty l Distributor Major Component Limited Warranty (Canada only) l Safety Restraint System Limited Warranty l Anti-perforation Limited Warranty l Federal Emission Control Warranty (U.S.A. only)


l Emission Defect Warranty l Emission Performance Warranty


l California Emission Control Warranty (U.S.A. only) l Emission Control Warranty (Canada only) l Replacement Parts and Accessories Limited Warranty l Tire Warranty


NOTE


Detailed warranty information is provided with your Mazda.


Form No.8U01-EA-05H


9-9


Mazdaspeed6_8U01-EA-05H_Edition1 Page310
Thursday, July 7 2005 1:4 PM


Black plate (310,1)


Customer Information and Reporting Safety Defects Warranty


Outside the United States


Government regulations in the United States require that automobiles meet specific emission regulations and safety standards. Therefore, vehicles built for use in the United States may differ from those sold in other countries.


The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries. We strongly recommend that you NOT take your Mazda outside the United States. However, in the event that you are moving to Canada permanently, Mazda vehicles built for use in the United States could be eligible for exportation to Canada with specific vehicle modifications to comply with the Canadian Motor Vehicle Safety requirements (CMVSS).


NOTE


The above is applicable for a permanent import/export situation and not related to travelers on vacation.


You may have the following problems if you do take your vehicle outside of the United States: l Recommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will


affect vehicle performance and damage the emission controls and engine.


l Proper repair facilities, tools, testing equipment, and replacement parts may not be


available.


Please refer to your Manufacturer's Warranty Booklet for more information.


9-10


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page311
Thursday, July 7 2005 1:4 PM


Black plate (311,1)


Customer Information and Reporting Safety Defects Warranty


Outside Canada


Government regulations in Canada require that automobiles meet specific emission regulations and safety regulations. Therefore, vehicles built for use in Canada may differ from those sold in other countries.


The differences may make it difficult or even impossible for your vehicle to receive satisfactory servicing in other countries. We strongly recommend that you NOT take your Mazda outside Canada. However, in the event that you are moving to the United States permanently, Mazda vehicles built for use in Canada could be eligible for exportation to the United States with specific vehicle modifications to comply with the United States Federal Motor Vehicle Safety Standards (FMVSS).


NOTE


The above is applicable for a permanent import/export situation and not related to travelers on vacation.


You may have the following problems if you do take your vehicle outside of Canada: l Recommended fuel may be unavailable. Any kind of leaded fuel or low-octane fuel will


affect vehicle performance and damage the emission controls and engine.


l Proper repair facilities, tools, testing equipment, and replacement parts may not be


available.


Please refer to your Manufacturer's Warranty Booklet for more information.


Form No.8U01-EA-05H


9-11


Mazdaspeed6_8U01-EA-05H_Edition1 Page312
Thursday, July 7 2005 1:4 PM


Black plate (312,1)


Customer Information and Reporting Safety Defects Warranty


Registering Your Vehicle in A Foreign Country (Except United States and Canada)


Government regulations in your country could require that automobiles meet specific emission and safety standards. Vehicles built for your country may differ from those built for other countries. In addition to registration problems, satisfactory service may be difficult or even impossible in another country.


The fuel specified for your vehicle may be unavailable.


Parts, servicing techniques, and tools necessary to maintain and repair your vehicle may be unavailable.


There might not be an Authorized Mazda Dealer in the country you plan to take your vehicle.


The Mazda warranty is valid only in certain countries.


9-12


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page313
Thursday, July 7 2005 1:4 PM


Black plate (313,1)


Customer Information and Reporting Safety Defects Warranty


Add-On Non-Genuine Parts and Accessories Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by Mazda for use with Mazda vehicles. When you install non-genuine parts or accessories, they could affect your vehicle's performance or safety systems; the Mazda warranty doesn't cover this. Before you install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.


WARNING


Installation of Non-Genuine Parts or Accessories: Installation of non-genuine parts or accessories is dangerous. Improperly designed parts or accessories could seriously affect your vehicle's performance or safety systems. This could cause you to have an accident or increase your chances of injuries in an accident. Always consult an Authorized Mazda Dealer before you install non- genuine parts or accessories.


Add-On Electrical and Electronic Equipment: Incorrectly choosing or installing improper add-on equipment or choosing an improper installer is dangerous. Essential systems could be damaged, causing engine stalling, air-bag (SRS) activation, ABS inactivation, or a fire in the vehicle. Be very careful in choosing and installing add-on electrical equipment, such as mobile telephones, two-way radios, stereo systems, and car alarm systems.


Mazda assumes no responsibility for death, injury, or expenses that may result from the installation of add-on non-genuine parts or accessories.


Form No.8U01-EA-05H


9-13


Mazdaspeed6_8U01-EA-05H_Edition1 Page314
Thursday, July 7 2005 1:4 PM


Black plate (314,1)


Customer Information and Reporting Safety Defects Cell Phones


Cell Phones Warning


WARNING


Use of Cell Phones and Other Devices by Driver: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver's hands. Use of these devices will cause the driver to be distracted and could lead to a serious accident. If a passenger is unable to use the device, pull off the right-of-way to a safe area before use. If use of a cell phone is necessary despite this warning, use a hands-free system to at least leave the hands free to drive the vehicle. Never use a cell phone or other electrical devices while the vehicle is moving and, instead, concentrate on the full-time job of driving. Please comply with the legal regulations concerning the use of communication equipment in vehicles in your country.


9-14


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page315
Thursday, July 7 2005 1:4 PM


Black plate (315,1)


Customer Information and Reporting Safety Defects Type Approval of Equipment


Type Approval of Equipment


Immobilizer system


Form No.8U01-EA-05H


9-15


Mazdaspeed6_8U01-EA-05H_Edition1 Page316
Thursday, July 7 2005 1:4 PM


Black plate (316,1)


Customer Information and Reporting Safety Defects Uniform Tire Quality Grading System (UTQGS)


Uniform Tire Quality Grading System (UTQGS) This information relates to the tire grading system developed by the U.S. National Highway Traffic Safety Administration for grading tires by tread wear, traction, and temperature performance.


qTread Wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one-and-a-half times as well on the government course as a tire graded 100.


The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm because of variations in driving habits, service practices and differences in road characteristics and climate.


qTraction-AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.


WARNING


The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include acceleration cornering (turning), hydroplaning, or peak traction characteristics.


qTemperature-A, B, C The temperature grades A (the highest), B, and C, represent the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperatures can lead to sudden tire failure.


Grade C corresponds to a level of performance which all passenger vehicle tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.


9-16


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page317
Thursday, July 7 2005 1:4 PM


Black plate (317,1)


Customer Information and Reporting Safety Defects Uniform Tire Quality Grading System (UTQGS)


WARNING


The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.


These grades will be added to the sidewalls of passenger vehicle tires over the next several years according to a schedule established by the NHTSA and the tire manufacturers.


The grade of tires available as standard or optional equipment on Mazda vehicles may vary with respect to grade.


ALL PASSENGER VEHICLE TIRES MUST CONFORM TO THESE GRADES AND TO ALL OTHER FEDERAL TIRE-SAFETY REQUIREMENTS.


qUniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A


UTQGS MARK (example)


TREADWEAR 200 TRACTION AA


TEMPERATURE A


Form No.8U01-EA-05H


9-17


Mazdaspeed6_8U01-EA-05H_Edition1 Page318
Thursday, July 7 2005 1:4 PM


Black plate (318,1)


Customer Information and Reporting Safety Defects Tire Information (U.S.A.)


Tire Labeling


Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a tire identification number for safety standard certification and in case of a recall.


qInformation on Passenger Vehicle Tires Please refer to the diagram below.


1. TIN: U.S. DOT tire identification number


2. Passenger car tire


3. Nominal width of tire in millimeters


4. Ratio of height to width (aspect ratio)


5. Radial


6. Rim diameter code


7. Load index & speed symbol


8. Severe snow conditions


9. Tire ply composition and materials used


10. Max. load rating


9-18


Form No.8U01-EA-05H


Mazdaspeed6_8U01-EA-05H_Edition1 Page319
Thursday, July 7 2005 1:4 PM


Black plate (319,1)


Customer Information and Reporting Safety Defects Tire Information (U.S.A.)


11. Tread wear, traction and temperature grades


12. Max. permissible inflation pressure


13. SAFETY WARNING


P215/65R15 95H is an example of a tire size and load index rating. Here is an explanation of the various components of that tire size and load index rating. Note that the tire size and load index rating may be different from the example.


Indicates a tire that may be installed on cars, SUVs, minivans and light trucks as designated by the Tire and Rim Association (T&RA).


NOTE


If your tire size does not begin with a letter this may mean it is designated by either ETRTO (European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing Association).


215

Loading...
x