Download PDF Manual


5-73


4. Then use the wheel wrench to loosen all the wheel


nuts. Don’t remove them yet.


5. Position the jack and raise the jack head until it fits firmly into the notch in the vehicle’s frame nearest the flat tire. Put the compact spare tire near you.


5-74


{CAUTION:


Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.


{CAUTION:


Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.


6. Raise the vehicle by turning the wheel wrench clockwise. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to fit underneath the wheel well.


7. Remove all of the wheel nuts. 8. Remove the flat tire.


5-75


9. Remove any rust or dirt


from the wheel bolts, mounting surfaces and spare wheel.


{CAUTION:


Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if you need to, to get all the rust or dirt off.


{CAUTION:


Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.


10. Install the compact spare tire.


5-76


11. Put the wheel nuts back on with the rounded end of


the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.


12. Lower the vehicle by turning the wheel wrench


counterclockwise. Lower the jack completely.


5-77


13. Tighten the wheel nuts


firmly in a crisscross sequence, as shown.


{CAUTION:


Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification. See “Capacities and Specifications” in the Index for wheel nut torque specification.


Improperly tightened wheel nuts can lead


Notice: to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque specification. See “Capacities and Specifications” in the Index for the wheel nut torque specification. Notice: Wheel covers will not fit on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare.


5-78


Storing the Flat Tire and Tools


{CAUTION:


Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


Store the flat tire in the compact spare tire compartment. Place the tire in the compartment, then secure the adapter and wing nut. Place the cover and the nut on top of the flat tire. Store the jack and the wrench in the foam tray.


A. Nut B. Cover C. Wing Bolt D. Adapter


E. Wrench F. Jack G. Tool Tray H. Flat Tire


5-79


Storing the Spare Tire and Tools


{CAUTION:


Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.


The compact spare tire is for temporary use only. Replace the compact spare tire with a full-size tire as soon as you can. See Compact Spare Tire on page 5-80. Store the compact spare tire and tools as shown in the diagram.


5-80


Tire


F. Jack G. Tool Tray H. Compact Spare


A. Nut B. Cover C. Wing Bolt D. Adapter E. Wrench Compact Spare Tire Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa).


After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can finish your trip and have your full-size tire repaired or replaced where you want. Of course, it’s best to replace your spare with a full-size tire as soon as you can. Your spare will last longer and be in good shape in case you need it again. Notice: When the compact spare is installed, don’t take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle. Don’t use your compact spare on other vehicles. And don’t mix your compact spare tire or wheel with other wheels or tires. They won’t fit. Keep your spare tire and its wheel together. Notice: Tire chains won’t fit your compact spare. Using them can damage your vehicle and can damage the chains too. Don’t use tire chains on your compact spare.


Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into flames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings and instructions. And always open your doors or windows when you are cleaning the inside. Never use these to clean your vehicle: • Gasoline • Benzene • Naphtha • Carbon Tetrachloride • Acetone • Paint Thinner • Turpentine • Lacquer Thinner • Nail Polish Remover


5-81


They can all be hazardous — some more than others — and they can all damage your vehicle, too. Do not use any of these unless this manual says you can. In many uses, these will damage your vehicle: • Alcohol • Laundry Soap • Bleach • Reducing Agents


Cleaning the Inside of Your Vehicle Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl, leather, plastic and painted surfaces with a clean, damp cloth. Cleaning Fabric/Carpet Your dealer has cleaners for the cleaning of fabric and carpet. They will clean normal spots and stains very well. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 5-88.


5-82


Here are some cleaning tips: • Always read the instructions on the cleaner label. • Clean up stains as soon as you can — before


they set.


• Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean


area often. A soft brush may be used if stains are stubborn.


• If a ring forms on fabric after spot cleaning, clean


the entire area immediately or it will set.


Using Cleaner on Fabric 1. Vacuum and brush the area to remove any


loose dirt.


2. Always clean a whole trim panel or section. Mask


surrounding trim along stitch or welt lines.


3. Follow the directions on the container label. 4. Apply cleaner with a clean sponge. Do not saturate


the material and do not rub it roughly.


5. As soon as you have cleaned the section, use a


sponge to remove any excess cleaner.


6. Wipe cleaned area with a clean, water-dampened


towel or cloth.


7. Wipe with a clean cloth and let dry.


Special Fabric Cleaning Problems Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: 1. Carefully scrape off excess stain, then sponge the


soiled area with cool water.


2. If a stain remains, follow the cleaning instructions


described earlier.


3. If an odor lingers after cleaning vomit or urine, treat


the area with a water and baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water.


4. Let dry. Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: 1. Carefully scrape off excess stain. 2. Clean with cool water and allow to dry completely. 3. If a stain remains, follow the cleaner instructions


described earlier.


Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You


may have to do this more than once.


• Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner. See your dealer for this product.


Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth. Then, let the leather dry naturally. Do not use heat to dry. • For stubborn stains, use a leather cleaner. • Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather.


• Soiled or stained leather should be cleaned


immediately. If dirt is allowed to work into the finish, it can harm the leather.


5-83


Care of Safety Belts Keep belts clean and dry.


{CAUTION:


Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.


Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. See Recommended Fluids and Lubricants on page 6-12.


Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions. Cleaning Interior Plastic Components Use only a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface finish. Cleaning Glass Surfaces Glass should be cleaned often. GM Glass Cleaner or a liquid household glass cleaner will remove normal tobacco smoke and dust films on interior glass. See Vehicle Care/Appearance Materials on page 5-88. Notice: glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the rear window defogger and the integrated radio antenna. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner.


If you use abrasive cleaners when cleaning


5-84


Cleaning the Outside of Your Vehicle The paint finish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Do not wash your vehicle in the direct rays of the sun. Use a car washing soap. Do not use strong soaps or chemical detergents. Be sure to rinse the vehicle well, removing all soap residue completely. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 5-88. Do not use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle.


Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “Washing Your Vehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 5-88. Your vehicle has a “basecoat/clearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on your vehicle.


5-85


Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your vehicle garaged or covered whenever possible. Cleaning Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid. The windshield is clean if beads do not form when you rinse it with water.


Grime from the windshield will stick to the wiper blades and affect their performance. Clean the blade by wiping vigorously with a cloth soaked in full-strength windshield washer solvent. Then rinse the blade with water. Check the wiper blades and clean them as necessary; replace blades that look worn. Cleaning Aluminum Wheels Keep your wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied. The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels. Do not take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels.


5-86


Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.


Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.


Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials avaliable from your dealer. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.


Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of the frame should be loosened before being flushed. Your dealer or an underbody car washing system can do this for you.


Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, GM will repair, at no charge to the owner, the surfaces of new vehicles damaged by this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever occurs first.


5-87


Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products.


Vehicle Care/Appearance Materials


(cont’d)


Description


Usage


Vehicle Care/Appearance Materials


Swirl Remover Polish


Description


Polishing Cloth Wax-Treated Tar and Road Oil Remover Chrome Cleaner and Polish White Sidewall Tire Cleaner


Vinyl Cleaner


Glass Cleaner


Chrome and Wire Wheel Cleaner


Finish Enhancer


Usage


Interior and exterior polishing cloth. Removes tar, road oil and asphalt. Use on chrome or stainless steel. Removes soil and black marks from whitewalls. Cleans vinyl tops, upholstery and convertible tops. Removes dirt, grime, smoke and fingerprints. Removes dirt and grime from chrome wheels and wire wheel covers. Removes dust, fingerprints, and surface contaminants. Spray on wipe off.


5-88


Cleaner Wax


Foaming Tire Shine Low Gloss


Wash Wax Concentrate


Spot Lifter


Odor Eliminator


Removes swirl marks, fine scratches and other light surface contamination. Removes light scratches and protects finish. Cleans, shines and protects in one easy step, no wiping necessary. Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Quickly and easily removes spots and stains from carpets, vinyl and cloth upholstery. Odorless spray odor eliminator used on fabrics, vinyl, leather and carpet.


See your General Motors parts department for these products. See Recommended Fluids and Lubricants on page 6-12.


Vehicle Identification


Vehicle Identification Number (VIN)


This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The 8th character in your VIN is the engine code. This code will help you identify your engine, specifications and replacement parts.


Service Parts Identification Label You’ll find this label on the bottom of your spare tire cover. It’s very helpful if you ever need to order parts. On this label is: • your VIN, • the model designation, • paint information and • a list of all production options and special


equipment.


Be sure that this label is not removed from the vehicle. Electrical System


Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should. Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Air Bag-Equipped Vehicle on page 1-60.


5-89


Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed.


Power Windows and Other Power Options A circuit breaker in the fuse panel protects the power windows. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed.


Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible links. This greatly reduces the chance of damage caused by electrical problems. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a new one of the identical size and rating. There are three fuse blocks in your vehicle: two instrument panel fuse blocks and the engine compartment fuse block. There are four spare fuses located in the driver’s side instrument panel end cap for your use. Instrument Panel Fuse Blocks There are two fuse panels for your vehicle. One is located on the driver’s side of the instrument panel and the other is located on the passenger’s side.


5-90


Instrument Panel Fuse Block (Driver’s Side) Your vehicle may not be equipped with all the fuses and features listed.


Fuses


WIPER


Usage


Windshield Wiper Motor, Washer Pump


Trunk Release Relay/Motor, Audio Amplifier/RFA


TRUNK REL/RADIO AMP TURN LPS PWR MIRROR Power Mirrors


Turn Signal Lamps


Fuses


AIR BAG BFC BATT PCM ACC DR LOCK IPC/BFC ACC STOP LPS HAZARD LPS IPC/HVAC BATT


Circuit Breakers PWR SEAT


Relay


TRUNK REL DR UNLOCK DR LOCK DRIVER DR UNLOCK


Usage


Air Bags Body Computer (BFC) Power Control Module (PCM) Door Lock Motors Cluster, Body Computer (BFC) Stop Lamps Hazard Lamps HVAC Head, Cluster, Data Link Connector


Power Seats


Usage


Usage


Trunk Relay Door Unlock Relay Door Lock Relay


Driver’s Door Unlock Relay


5-91


Instrument Panel Fuse Block (Passenger’s Side) Your vehicle may not be equipped with all the fuses and features listed.


Fuse INST LPS CRUISE SW LPS


CRUISE SW


HVAC BLOWER CRUISE FOG LPS INT LPS RADIO BATT SUNROOF


Usage Interior Lamp Dimming Steering Wheel Cruise Control Switch Lamps Steering Wheel Cruise Control Switches


HVAC Blower Motor


Cruise Control Fog Lamps Interior Courtesy Lamps Radio, XM™ Satellite Radio/DAB Power Sunroof


Circuit Breaker Usage


PWR WNDW Power Windows


Relay


FOG LPS


Usage Fog Lamps


5-92


Engine Compartment Fuse Block Your vehicle may not be equipped with all the fuses and features listed. The engine compartment fuse block is located on the driver’s side of the vehicle, near the battery.


Fuse


Usage


Ignition Switch Right Electrical Center-Fog Lamps, Radio, Body Function Control Module, Interior Lamps Left Electrical Center-Stop Lamps, Hazard Lamps, Body Function Control Module, Cluster, Climate Control System Anti-Lock Brakes Left Electrical Center-Power Seats, Power Mirrors, Door Locks, Trunk Release, Audio Amplifier, Remote Keyless Entry Not Used Ignition Switch Cooling Fan #1


Relays


Usage


10
11
12
13
14
15


Rear Defog Not Used Starter (V6 only) Cooling Fan #1
HVAC Blower (Climate Control) Cooling Fan #2
Cooling Fan


5-93


Relays


Usage


Fuses


Usage


16
17
18
19
20
21
22


Fuses 23–32


33


34


35
36


37


38
39
40


Air Conditioning Compressor Not Used Fuel Pump Automatic Headlamp System Automatic Headlamp System Horn Daytime Running Lamps (DRL)


Usage


Spare Fuse Holder Rear Defog Accessory Power Outlets, Cigarette Lighter Generator Not Used Air Conditioning Compressor, Body Function Control Module Automatic Transaxle Powertrain Control Module (PCM) Anti-Lock Brakes (ABS)


41


42


43
44
45


46


47


48
49
50
51
52
53
54
55
56
57


Ignition System Back-Up Lamps, Brake Transaxle Shift Interlock Horn PCM Parking Lamps Climate Control System, Air Conditioning Canister Vent Valve, Exhaust Oxygen Sensors Fuel Pump, Injectors Not Used Right Headlamp Left Headlamp Cooling Fan #2
HVAC Blower (Climate Control) Crank (V6 only) Cooling Fan #2 Ground Fuse Puller for Mini Fuses Not Used


5-94


Capacities and Specifications All capacities are approximate. When adding, be sure to fill to the appropriate level or as recommended in this manual.


Capacities


Capacities


Application


Air Conditioning Refrigerant R134a Use Refrigerant Oil, R134a Systems


Automatic Transaxle Complete Overhaul


Cooling System


2.2L L4 † Engine 3400 V6 Engine


Engine Oil with Filter


2.2L L4 † Engine 3400 V6 Engine


Fuel Tank


Manual Transaxle


Complete Overhaul


Wheel Nut Torque †ECOTEC™


English


1.4 lbs.


9.5 quarts


8.6 quarts 13.6 quarts


5.0 quarts 4.0 quarts


14.1 gallons


1.8 quarts


100 lb-ft


Metric


0.6 kg


9.0 L


8.2 L 12.9 L


4.8 L 3.8 L


53.4 L


1.7 L


140 Y


5-95


See Recommended Fluids and Lubricants on page 6-12.


Engine


2.2L L4 †


3400 V6


Engine Specifications


VIN Code


Transaxle Automatic


Manual


Automatic


Manual


Spark Plug Gap


0.042 inch (1.06 mm)


0.060 inch (1.52 mm)


5-96


Section 6


Maintenance Schedule


Maintenance Schedule ......................................6-2
Introduction ...................................................6-2
Maintenance Requirements ..............................6-2
Your Vehicle and the Environment ....................6-2
Using Your Maintenance Schedule ....................6-3
Scheduled Maintenance ...................................6-4
Additional Required Services ............................6-6
Maintenance Footnotes ...................................6-7


Owner Checks and Services ............................6-8
At Each Fuel Fill ............................................6-8
At Least Once a Month ...................................6-9
At Least Once a Year .....................................6-9
Recommended Fluids and Lubricants ...............6-12
Normal Maintenance Replacement Parts ..........6-13
Maintenance Record .....................................6-14


6-1


Maintenance Schedule


Introduction Important: Keep engine oil at the proper level and change as recommended.


Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details.


Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance may not be covered by warranty.


Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance is important. Improper vehicle maintenance can even affect the quality of the air we breathe. Improper fluid levels or the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to keep your vehicle in good condition, be sure to maintain your vehicle properly.


6-2


Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of all the different ways people use their vehicles, maintenance needs vary. You may need more frequent checks and replacements. So please read the following and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your GM Goodwrench dealer. This schedule is for vehicles that: • carry passengers and cargo within recommended


limits. You will find these limits on the tire and loading information label. See Loading Your Vehicle on page 4-34.


• are driven on reasonable road surfaces within legal


driving limits.


• use the recommended fuel. See Gasoline Octane


on page 5-4.


The services in Scheduled Maintenance on page 6-4
should be performed when indicated. See Additional Required Services on page 6-6 and Maintenance Footnotes on page 6-7 for further information.


{CAUTION:


Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your GM Goodwrench dealer to have a qualified technician do the work.


Some maintenance services can be complex. So, unless you are technically qualified and have the necessary equipment, you should have your GM Goodwrench dealer do these jobs. When you go to your GM Goodwrench dealer for your service needs, you will know that GM-trained and supported service technicians will perform the work using genuine GM parts. If you want to get service information, see Service Publications Ordering Information on page 7-12.


6-3


Owner Checks and Services on page 6-8 tells you what should be checked, when to check it and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, fluids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Normal Maintenance Replacement Parts on page 6-13. When your vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle. We recommend the use of genuine GM parts.


Scheduled Maintenance When the CHANGE OIL light comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year. However, your engine oil and filter must be changed at least once a year and at this time the system must be reset. Your GM Goodwrench dealer has GM-trained service technicians who will perform this work using genuine GM parts and reset the system.


If the engine oil life system is ever reset accidentally, you must service your vehicle within 3,000 miles (5 000 km) since your last service. Remember to reset the oil life system whenever the oil is changed. See Engine Oil on page 5-15 for information on the Engine Oil Life System and resetting the system. When the CHANGE OIL light appears, certain services, checks and inspections are required. Required services are described in the following for “Maintenance I” and “Maintenance II.” Generally, it is recommended that your first service be Maintenance I, your second service be Maintenance II and that you alternate Maintenance I and Maintenance II thereafter. However, in some cases, Maintenance II may be required more often. Maintenance I — Use Maintenance I if the CHANGE OIL light comes on within ten months since vehicle was purchased or Maintenance II was performed. Maintenance II — Use Maintenance II if the previous service performed was Maintenance I. Always use Maintenance II whenever the light comes on ten months or more since the last service or if the light has not come on at all for one year.


6-4


Service


Maintenance I Maintenance II


Change engine oil and filter. Reset oil life system. See Engine Oil on page 5-15. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner filter. If necessary, replace filter. See Engine Air Cleaner/Filter on page 5-20. An Emission Control Service. See footnote †. Rotate tires and check inflation pressures and wear. See Tires on page 5-54. Inspect brake system. See footnote (a). Check engine coolant and windshield washer fluid levels and add fluid as needed. Perform any needed additional services. See “Additional Required Services” in this section. Inspect suspension and steering components. See footnote (b). Inspect engine cooling system. See footnote (c). Inspect wiper blades. See footnote (d). Inspect restraint system components. See footnote (e). Lubricate body components. See footnote (f). Inspect throttle system. See footnote (g).


• • • • • •



• • • • • •


• • • • • • •


6-5


Additional Required Services The following services should be performed at the first maintenance service (I or II) after the indicated miles (kilometers) shown for each item.


25,000
(41 500)


50,000
(83 000)


75,000


(125 000)


100,000
(166 000)


125,000
(207 500)


150,000
(240 000)


























Service


Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner filter. See Engine Air Cleaner/Filter on page 5-20. An Emission Control Service. Change automatic transaxle fluid and filter (severe service only). See footnote (h). Replace spark plugs. Inspect spark plug wires (V6 only). An Emission Control Service. Engine cooling system service (or every 5 years, whichever occurs first). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service.


6-6


Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded. (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose or missing part or signs of wear. Inspect power steering lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. (c) Visually inspect hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year.


(d) Visually inspect wiper blades for wear or cracking. Replace blade inserts that appear worn or damaged or that streak or miss areas of the windshield. (e) Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced. Also look for any opened or broken air bag coverings, and have them repaired or replaced. (The air bag system does not need regular maintenance.) (f) Lubricate all key lock cylinders, door hinges and latches, hood hinges and latches and trunk lid hinges and latches. More frequent lubrication may be required when exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth will make them last longer, seal better and not stick or squeak. (g) Check system for interference or binding and for damaged or missing parts. Replace parts as needed. Replace any components that have high effort or excessive wear. Do not lubricate accelerator or cruise control cables.


6-7


(h) Change automatic transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions:


− In heavy city traffic where the outside temperature


regularly reaches 90°F (32°C) or higher.


− In hilly or mountainous terrain. − When doing frequent trailer towing. − Uses such as found in taxi, police or delivery


service.


If you do not use your vehicle under any of these conditions, the fluid and filter do not require changing. (i) Drain, flush and refill cooling system. See Engine Coolant on page 5-23 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and filler neck. Pressure test the cooling system and pressure cap. (j) A fluid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the fluid level checked. Add fluid if needed.


Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench dealer can assist you with these checks and services.


Be sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Recommended Fluids and Lubricants on page 6-12.


It is important to check your oil regularly


At Each Fuel Fill It is important to perform these underhood checks at each fuel fill. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-15 for further details. Notice: and keep it at the proper level. Failure to keep your engine oil at the proper level can cause damage to your engine not covered by your warranty. Engine Coolant Level Check Check the engine coolant level and add DEX-COOL® coolant mixture if necessary. See Engine Coolant on page 5-23 for further details. Windshield Washer Fluid Level Check Check the windshield washer fluid level in the windshield washer tank and add the proper fluid if necessary.


6-8


At Least Once a Month Tire Inflation Check Visually inspect your tires and make sure tires are inflated to the correct pressures. Don’t forget to check your spare tire. See Tires on page 5-54 for further details. Cassette Tape Player Service Clean cassette tape player. Cleaning should be done every 50 hours of tape play. See Audio System(s) on page 3-39 for further details.


At Least Once a Year Starter Switch Check


{CAUTION:


When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before you start, be sure you have enough room


around the vehicle.


2. Firmly apply both the parking brake and the regular


brake. See Parking Brake on page 2-27 if necessary. Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts.


3. Try to start the engine in each gear. The starter should work only in PARK (P) or NEUTRAL (N). If the starter works in any other position, contact your GM Goodwrench dealer for service.


6-9


Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to OFF in each shift lever position. • With an automatic transaxle, the key should turn to OFF only when the shift lever is in PARK (P). The key should come out only in OFF.


• With a manual transaxle, the key should turn to OFF only when the shift lever is in reverse. The key should come out only in OFF.


Contact your GM Goodwrench dealer if service is required.


Automatic Transaxle Shift Lock Control System Check


{CAUTION:


When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured.


1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.


2. Firmly apply the parking brake. See Parking Brake


on page 2-27 if necessary. Be ready to apply the regular brake immediately if the vehicle begins to move.


3. With the engine off, turn the key to the ON position,


but don’t start the engine. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), contact your GM Goodwrench dealer for service.


6-10


Parking Brake and Automatic Transaxle Park (P) Mechanism Check


{CAUTION:


When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.


Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With


the engine running and transaxle in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the parking brake only.


• To check the PARK (P) mechanism’s holding


ability: With the engine running, shift to PARK (P). Then release the parking brake followed by the regular brake.


Contact your GM Goodwrench dealer if service is required. Underbody Flushing Service At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.


6-11


Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer.


Usage


Engine Oil


Engine Coolant


Hydraulic Brake


System


Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol. To determine the proper viscosity for your vehicle’s engine, see Engine Oil on page 5-15. 50/50 mixture of clean, drinkable water and use only DEX-COOL® Coolant. See Engine Coolant on page 5-23. Delco Supreme 11 Brake Fluid or equivalent DOT-3 brake fluid.


Windshield


Washer Solvent GM Optikleen® Washer Solvent.


Hydraulic


Clutch System


Hydraulic Clutch Fluid (GM Part No. U.S. 12345347 in Canada 10953517) or equivalent DOT-3
brake fluid.


6-12


Usage


Fluid/Lubricant


Power Steering


System


Manual Transaxle Automatic Transaxle


Key Lock Cylinders


Hood Latch Assembly, Secondary


Latch, Pivots, Spring Anchor and Release


Pawl


GM Power Steering Fluid (GM Part No. U.S. 89021184, in Canada 89021186). DEXRON®-III Automatic Transmission Fluid. DEXRON®-III Automatic Transmission Fluid. Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474).


Lubriplate Lubricant Aerosol (GM Part No. U.S. 12346293, in Canada 992723) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB.


Hood and Door


Hinges


Weatherstrip Conditioning


Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Dielectric Silicone Grease (GM Part No. U.S. 12345579, in Canada 992887).


Normal Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer.


Part Engine Air Cleaner/Filter


2.2 L L4† Engine 3400 V6


Engine Oil Filter


2.2 L L4† Engine 3400 V6


Spark Plugs


2.2 L L4† Engine 3400 V6


Windshield Wiper Blades


Passenger’s Side — 17.0 inches (43.0 cm) Driver’s Side — 22.0 inches (56.0 cm)


†ECOTEC™


GM Part No.


ACDelco® Part No.


25098845
25161977


24460713
25010792


A1172C A1279C


PF2244G


PF47


25337472 (Platinum Plug) 12568387 (Platinum Plug)


41–981 (Platinum Plug) 41–10 (Platinum Plug)


Type — Shepherd’s Hook


22121329
22155307


— —


6-13


Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. Also, you should retain all maintenance receipts.


Date


Odometer Reading


Serviced By


Maintenance I or Maintenance II


Services Performed


Maintenance Record


6-14


Date


Odometer Reading


Serviced By


Maintenance I or Maintenance II


Services Performed


Maintenance Record (cont’d)


6-15


Date


Odometer Reading


Serviced By


Maintenance I or Maintenance II


Services Performed


Maintenance Record (cont’d)


6-16


Section 7


Customer Assistance Information


Customer Assistance Information ......................7-2
Customer Satisfaction Procedure ......................7-2
Online Owner Center ......................................7-4
Customer Assistance for Text Telephone


(TTY) Users ...............................................7-4
Customer Assistance Offices ............................7-4
GM Mobility Program for Persons with


Disabilities ..................................................7-6
Roadside Assistance Program ..........................7-6
Courtesy Transportation ...................................7-8
Vehicle Data Collection and Event Data


Records ...................................................7-10


Reporting Safety Defects ................................7-11


Reporting Safety Defects to the United States


Government ..............................................7-11


Reporting Safety Defects to the Canadian


Government ..............................................7-11
Reporting Safety Defects to General Motors .....7-12
Service Publications Ordering Information .........7-12


7-1


Customer Assistance Information


Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Oldsmobile. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur. If your concern has not been resolved to your satisfaction, the following steps should be taken:


STEP ONE: Discuss your concern with a member of dealership management. Normally, concerns can be quickly resolved at that level. If the matter has already been reviewed with the sales, service or parts manager, contact the owner of the dealership or the general manager.


STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the Oldsmobile Customer Assistance Center by calling 1-800-442-6537. In Canada, contact GM of Canada Customer Communication Centre in Oshawa by calling 1-800-263-3777 (English) or 1-800-263-7854 (French).


We encourage you to call the toll-free number in order to give your inquiry prompt attention. Please have the following information available to give the Customer Assistance Representative: • Vehicle Identification Number (This is available from the vehicle registration or title, or the plate at the top left of the instrument panel and visible through the windshield.)


• Dealership name and location • Vehicle delivery date and present mileage When contacting Oldsmobile, please remember that your concern will likely be resolved at a dealer’s facility. That is why we suggest you follow Step One first if you have a concern.


7-2


STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you should file with the BBB Auto Line Program to enforce any additional rights you may have. Canadian owners refer to your Warranty and Owner Assistance Information booklet for information on the Canadian Motor Vehicle Arbitration Plan (CAMVAP).


The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to filing a court action, use of the program is free of charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you.


You may contact the BBB Auto Line Program using the toll-free telephone number or write them at the following address:


BBB Auto Line Program Council of Better Business Bureaus, Inc. 4200 Wilson Boulevard Suite 800
Arlington, VA 22203-1804
Telephone: 1-800-955-5100


This program is available in all 50 states and the District of Columbia. Eligibility is limited by vehicle age, mileage and other factors. General Motors reserves the right to change eligibility limitations and/or discontinue its participation in this program.


7-3


Online Owner Center The Owner Center is a resource for your GM ownership needs. You can find your specific vehicle information all in one place. The Owner Center allows you to: • Get e-mail service reminders. • Access information about your specific vehicle,


including tips and videos and an electronic version of this owner’s manual. (United States only)


• Keep track of your vehicle’s service history and


maintenance schedule.


• Find GM dealers for service nationwide. • Receive special promotions and privileges only


available to members. (United States only)


Refer to the web for updated information. To register your vehicle, visit www.MyGMLink.com. (United States) or My GM Canada within www.gmcanada.com (Canada).


Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Oldsmobile has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Oldsmobile by dialing: 1-800-833-OLDS (6537). (TTY users in Canada can dial 1-800-263-3830.)


Customer Assistance Offices Oldsmobile encourages customers to call the toll-free number for assistance. If a U.S. customer wishes to write to Oldsmobile, the letter should be addressed to Oldsmobile’s Customer Assistance Center.


7-4


United States – Customer Assistance


Oldsmobile Customer Assistance Center P.O. Box 33171
Detroit, MI 48232-5171
1-800-442-6537
1-800-833-6537 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-442-OLDS (6537) Fax Number: 313-381-0022


Overseas – Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) – Customer Assistance


General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740
Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000
Long Distance: 011-52-53 29 0 800


From Puerto Rico:


1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022


From U.S. Virgin Islands:


1-800-496-9994
Fax Number: 313-381-0022


Canada – Customer Assistance


General Motors of Canada Limited Customer Communication Centre, 163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7
1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs) Roadside Assistance: 1-800-268-6800


7-5


GM Mobility Program for Persons with Disabilities


This program, available to qualified applicants, can reimburse you up to $1,000
toward eligible aftermarket driver or passenger adaptive equipment you may require for your vehicle (hand controls, wheelchair/ scooter lifts, etc.).


This program can also provide you with free resource information, such as area driver assessment centers and mobility equipment installers. The offer is available for a limited period of time from the date of vehicle purchase/lease. For more details, or to determine your vehicle’s eligibility, see your GM dealer or call the GM Mobility Assistance Center at 1-800-323-9935. Text telephone (TTY) users, call 1-800-833-9935. GM of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. All TTY users call 1-800-263-3830.


7-6


Roadside Assistance Program Security While You Travel 1-800-442-OLDS (6537) As the proud owner of a new Oldsmobile vehicle, you are automatically enrolled in the Oldsmobile Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road. Oldsmobile’s Roadside Assistance toll-free number is staffed by courteous and capable Roadside Assistance Representatives who are available 24 hours a day, 365 days a year. We will provide the following services during the Bumper-to-Bumper warranty period, at no expense to you: • Fuel delivery • Lock-out service (identification required) • Tow to the nearest dealership for warranty service or


in the event of a vehicle-disabling accident


• Flat tire change • Jump starts • Minor repairs to disabled vehicles


• Assistance when vehicle is mired in sand, mud or


snow


• Trip routing • Trip interruption expense benefits • Dealership locator service Oldsmobile Roadside Assistance specifically excludes coverage for mounting, dismounting or changing of snow tires, chains or other traction devices. In some cases, where service is impractical, the driver may be authorized to obtain other service for which reimbursement is provided. In many instances, mechanical failures are covered under Oldsmobile’s comprehensive warranty. However, when other services are utilized, our Roadside Assistance Representatives will explain any payment obligations you might incur. For prompt and efficient assistance when calling, please provide the following to the Roadside Assistance Representative: • Location of vehicle • Telephone number of your location • Vehicle model, year and color


• Mileage of vehicle • Vehicle Identification Number (VIN) • Vehicle license plate number Oldsmobile reserves the right to limit services or reimbursement to an owner or driver when, in Oldsmobile’s judgement, the claims become excessive in frequency or type of occurrence. While we hope you never have the occasion to use our service, it is added security while traveling for you and your family. Remember, we’re only a phone call away. Oldsmobile Roadside Assistance: 1-800-442-OLDS (6537), text telephone (TTY) users, call 1-888-889-2438. Canadian Roadside Assistance Vehicles purchased in Canada have an extensive roadside assistance program accessible from anywhere in Canada or the United States. Please refer to the Warranty and Owner Assistance Information book.


7-7


Courtesy Transportation Oldsmobile has always exemplified quality and value in its offering of motor vehicles. To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles. The Courtesy Transportation program is offered to retail purchase/lease customers in conjunction with the Bumper-to-Bumper coverage provided by the New Vehicle Limited Warranty. Several transportation options are available when warranty repairs are required. This will reduce your inconvenience during warranty repairs. Plan Ahead When Possible When your vehicle requires warranty service, you should contact your dealer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer can help minimize your inconvenience. If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership, let them know this, and ask for instructions.


If the dealer requests that you simply drop the vehicle off for service, you are urged to do so as early in the work day as possible to allow for same day repair. Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Oldsmobile helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Participating dealers can provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule. This includes a one way or round trip shuttle ride to a destination up to 10 miles from the dealership. Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, reimbursement (five days maximum) may be available for the use of public transportation such as taxi or bus. In addition, should you arrange transportation through a friend or relative, reimbursement for reasonable fuel expenses (five day maximum) may be available. Claim amounts should reflect actual costs and be supported by original receipts.


7-8


Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum of $30 a day and must be supported by receipts. This requires that you sign and complete a rental agreement and meet state, local and rental vehicle provider requirements. Requirements vary and may include minimum age requirements, insurance coverage, credit card, etc. You are responsible for fuel usage charges and may also be responsible for taxes, levies, usage fees, excessive mileage or rental usage beyond the completion of the repair. Generally it is not possible to provide a like-vehicle as a courtesy rental. Additional Program Information Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information.


Courtesy Transportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for specific information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. Canadian Vehicles: For warranty repairs during the Complete Vehicle Coverage period of the General Motors of Canada New Vehicle Limited Warranty, alternative transportation may be available under the Courtesy Transportation Program. Please consult your dealer for details. General Motors reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion.


7-9


Vehicle Data Collection and Event Data Records Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations. Some information may be stored during regular operations to facilitate repair of detected malfunctions; other information is stored only in a crash or near crash event by computer systems commonly called event data recorders (EDR). In a crash or near crash event, computer systems, such as the Airbag Sensing and Diagnostic Module (SDM) in your vehicle may record information about the condition of the vehicle and how it was operated, such as engine speed, brake applications, throttle position, vehicle speed, seat belt usage, airbag readiness, airbag performance data, and the severity of a collision. This information has been used to improve vehicle crash performance and may be used to improve crash performance of future vehicles and driving safety. Unlike


7-10


the data recorders on many airplanes, these on-board systems do not record sounds, such as conversation of vehicle occupants. To read this information, special equipment is needed and access to the vehicle or the SDM is required. GM will not access information about a crash event or share it with others other than • with the consent of the vehicle owner or, if the


vehicle is leased, with the consent of the lessee,


• in response to an official request of police or similar


government office,


• as part of GM’s defense of litigation through the


discovery process, or


• as required by law. In addition, once GM collects or receives data, GM may • use the data for GM research needs, • make it available for research where appropriate


confidentiality is to be maintained and need is shown, or


• share summary data which is not tied to a specific


vehicle with non-GM organizations for research purposes.


Others, such as law enforcement, may have access to the special equipment that can read the information if they have access to the vehicle or SDM. If your vehicle is equipped with OnStar, please check the OnStar subscription service agreement or manual for information on its operations and data collection. Reporting Safety Defects


Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying General Motors. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or General Motors.


To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in the Washington, D.C. area) or write to:


NHTSA, U.S. Department of Transportation Washington, D.C. 20590


You can also obtain other information about motor vehicle safety from the hotline.


Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited. You may write to:


Transport Canada 330 Sparks Street Tower C Ottawa, Ontario K1A 0N5


7-11


Transmission, Transaxle, Transfer Case Unit Repair Manual This manual provides information on unit repair service procedures, adjustments, and specifications for GM transmissions, transaxles, and transfer cases. RETAIL SELL PRICE: $50.00
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).


Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-442-6537, or write: Oldsmobile Customer Assistance Center P.O. Box 33171
Detroit, MI 48232-5171


In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French). Or, write: General Motors of Canada Limited Customer Communication Centre 163-005
1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7


Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle, suspension, brakes, electrical, steering, body, etc. RETAIL SELL PRICE: $120.00


7-12


Owner’s Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner’s manual will include the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner’s Manual, and Warranty Booklet. RETAIL SELL PRICE: $35.00
Without Portfolio: Owner’s Manual only. RETAIL SELL PRICE: $25.00
Current and Past Model Order Forms Service Publications are available for current and past model GM vehicles. To request an order form, please specify year and model name of the vehicle.


ORDER TOLL FREE: 1-800-551-4123
Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: www.helminc.com Or you can write to:


Helm, Incorporated P. O. Box 07130
Detroit, MI 48207


Prices are subject to change without notice and without incurring obligation. Allow ample time for delivery. Note to Canadian Customers: All listed prices are quoted in U.S. funds. Canadian residents are to make checks payable in U.S. funds.


7-13


✍ NOTES


7-14


A


Accessory Power Outlets ................................. 3-18
Adding Washer Fluid ....................................... 5-36
Additional Program Information ........................... 7-9
Additives, Fuel ................................................. 5-5
Add-On Electrical Equipment ............................ 5-89
Adjusting the Speakers


(Balance/Fade) ............................ 3-42, 3-47, 3-58


Air Bag


Readiness Light .......................................... 3-26


Air Bag System, Supplemental Restraint


System (SRS) ............................................. 1-54
Air Cleaner/Filter, Engine ................................. 5-20
Airbag Sensing and Diagnostic Module (SDM) .... 7-10
AM ............................................................... 3-67
Antenna, Backglass ......................................... 3-69
Antenna, XM™ Satellite Radio Antenna System .. 3-69
Anti-lock Brake System (ABS) ............................ 4-7
Anti-Lock Brake System Warning Light ............... 3-29
Appearance Care ............................................ 5-81
Care of Safety Belts .................................... 5-84
Chemical Paint Spotting ............................... 5-87
Cleaning the Inside of Your Vehicle ................ 5-82
Cleaning the Outside of Your Vehicle .............. 5-85
Finish Damage ............................................ 5-87
Sheet Metal Damage ................................... 5-87
Underbody Maintenance ............................... 5-87
Vehicle Care/Appearance Materials ................ 5-88
Weatherstrips .............................................. 5-84


Ashtrays ........................................................ 3-19
Audio System(s) ............................................. 3-39
Backglass Antenna ...................................... 3-69
Care of Your Cassette Tape Player ................ 3-67
Care of Your CD Player ............................... 3-68
Care of Your CDs ........................................ 3-68
Chime Level Adjustment ............................... 3-69
Radio with Cassette and CD ......................... 3-55
Radio with CD .................................... 3-40, 3-45
Setting the Time for Radios with Radio Data


Loading...
x