Download PDF Manual

check the generator belt. If the belt is loose, broken, missing or if the light remains on, see an authorized NISSAN dealer immediately.


CAUTION


Do not continue driving if the belt is loose, broken or missing.


Low fuel warning light (if so equipped)


This light comes on when the fuel in the tank is low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel remaining in the tank when the fuel gauge needle reaches E (Empty).


Door open warning light


This light comes on when any of the doors are not closed securely while the ignition key is in the ON position. Low washer light (Canada only)


fluid warning


This light comes on when the washer tank fluid is at a low level. Add washer fluid as necessary. See ‘‘Window washer fluid’’ in the ‘‘Do-it-yourself’’ section of this manual. 4-wheel drive indicator light This light comes on when the transfer shift control lever is in the 4H or 4L position.


Instruments and controls 2-9


Z X


WARNING


O When parking always make sure the transfer control lever is in the 2H, 4H or 4L position and the parking brake is applied.


O Failure to engage the transfer con- trol lever in 2H, 4H or 4L could result in the vehicle moving unexpectedly, which could cause serious personal injury or property damage.


Automatic transmission park model) warning light ( This light indicates that the automatic trans- mission parking function is not engaged. If the transfer control lever is not secured in any drive position while the automatic trans- mission selector lever is in the P (Park) position, the transmission will disengage and the vehicle may move unexpectedly. Shift the transfer control lever into the 2H, 4H, or 4L position when the warning light comes on. O When parking, always make sure that the transfer control lever is in 2H, 4H, or 4L and the parking brake is set.


2-10 Instruments and controls


O If the ATP light is ON, this indicates that the automatic transmission P (Park) po- sition will not function and the transfer lever is in the N (Neutral) position.


O Failure to engage the transfer control lever in 2H, 4H, or 4L could result in the vehicle moving unexpectedly, resulting in serious personal injury or property dam- age.


WARNING


O If the ATP light is ON, this indicates that the automatic transmission P (Park) position will not function and the transfer control lever is in the N (Neutral) position.


Automatic transmission oil temperature warning light


model)


This light comes on when the automatic transmission oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off.


CAUTION


Continued vehicle operation when the A/T oil temperature warning light is on may damage the automatic transmis- sion.


Cruise indicator light (if so equipped)


This light comes on while the vehicle speed is controlled by the cruise control system. If the CRUISE indicator blinks, have the sys- tem checked by an authorized NISSAN dealer.


or


Anti-lock brake warn- ing light


If the light comes on while the engine is running, it may indicate a potential problem with the anti-lock brake system. Have the system checked by an authorized NISSAN dealer. If an abnormality occurs in the system, the anti-lock function ceases but the ordinary brakes continue to operate normally. If the light comes on while you are driving, contact an authorized NISSAN dealer for repair.


Z X


Overdrive off indicator light (automatic transmission only) This light comes on when the overdrive switch is pushed to the OFF position. Key reminder chime The chime sounds when the driver’s door is opened and the key is in the ignition switch. Take the ignition key when you leave the vehicle. Light reminder chime A chime sounds if is opened with the headlight switch on unless the ignition key is in the ON position. Turn the headlight switch off when you leave the vehicle. Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard.


the driver’s door


Malfunction indicator (MIL)


light


If the malfunction indicator light comes on steady or blinks while the engine is running, it may indicate a potential emission control problem. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel filler cap is installed and closed tightly, and that the vehicle has at least three gallons of fuel in the fuel tank. lamp After a few driving trips, should turn off if no other potential emission control system problem exists. Operation The malfunction indicator light will come on in one of two ways: O Malfunction indicator lamp on steady − An emission control system malfunction has been detected. Check the fuel filler cap. If the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp


the


does not turn off after a few driving trips, have the vehicle inspected by an autho- rized NISSAN dealer. You do not need to have your vehicle towed to the dealer.


O Malfunction indicator light blinking − An engine misfire has been detected which may damage the emission control sys- tem. To reduce or avoid emission control system damage: O do not drive at speeds above 45 MPH O avoid hard acceleration or deceleration. O avoid steep uphill grades. O if possible, reduce the amount of cargo


(72 km/h).


being hauled or towed.


The malfunction indicator light may stop blinking and come on steady. Have the vehicle inspected by an autho- rized NISSAN dealer. You do not need to have your vehicle towed to the dealer.


CAUTION


Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.


Instruments and controls 2-11


Z X


THEFT WARNING (if so equipped)


O When the


button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder the doors are already locked. The horn may or may not beep once. Refer to ‘‘silencing the horn beep feature’’ later in this section.


that


O If a door is open and you push the button the doors lock but the horn does not chirp and the hazard lights do not flash.


The system can be activated even if the windows are open. 5. Confirm that


the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then begins to flash once every three seconds. The system is now activated. If, during this 30 second time period, a door is unlocked by the key or the multi-remote controller, or the ignition key is turned to ACC or ON, the system will not activate. O If the key is turned slowly when lock- ing the door, the system may not acti- vate. Furthermore, if the key is turned excessively to the unlock position, the system may be deactivated when the


IC0005


The theft warning system provides visual and audio alarm signals if parts of the vehicle are disturbed. How to activate the theft warning system 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all the doors. 4. Push the


button on the multi-remote controller. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.


2-12 Instruments and controls


key is removed. If the indicator light fails to glow for 30 seconds, unlock the door once and lock it again.


O Even when the driver and/or passen- gers are in the vehicle, the system will activate with all doors and hood closed and locked and with the igni- tion key in the OFF position. Turn the ignition key to ACC or ON to turn the system off.


The theft warning system is NOT activated if one of the following occurs: O A door is unlocked or the ignition key is turned to the ACC or ON position during the 30 seconds in which the SECURITY light stays on.


O The SECURITY light blinks at a steady 1/2 second on - 1/2 second off rate (a door, or the hood is open and the key is not in the ACC or ON position). When the ignition key is turned to the ACC or ON position, the SECURITY light turns off.


Theft warning system operation The theft warning system emits the follow- ing alarm: O The headlights blink and the horn sounds


Z X


intermittently. In addition, the starter mo- tor does not operate.


O The alarm automatically turns off after 2
to 3 minutes. However, the alarm reacti- vates if the vehicle is tampered with again. The alarm can be shut off by unlocking a door with the key or by button on the multi- pressing the remote controller.


The alarm is activated by: O opening a door without using the key (even if the door is unlocked by releasing the inside lock knob).


O opening the hood. How to stop the alarm The alarm stops only by unlocking a door with button on the the key or by pressing the multi-remote controller. The alarm does not stop if the ignition switch is turned to ACC or ON position.


The hazard lights will quickly flash three times to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not silence the horn if the alarm is triggered. If the system does not operate as de- scribed above, have it checked by an authorized NISSAN dealer.


AIC1037


Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the multi-remote controller. To deactivate: Press and hold the buttons for at least two


and seconds. The hazard lights will quickly flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the


and buttons for at least two seconds


once more.


Instruments and controls 2-13


Z X


HEADLIGHT AND TURN SIGNAL SWITCH


light illuminates. Pull it back


on and the to select the low beam. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The day- time running lights operate with the head- light switch in the OFF position or in the position. Turn the headlight switch illumination to the when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime run- ning lights will remain on until the ignition switch is turned off.


position for


full


Lighting Turn the switch to the The front combination, rear combination, license plate and instrument panel lights come on.


position:


position:


Turn the switch to the The headlights come on and all the other lights remain on. To select the high beam function, push the lever forward. The high beam lights come


When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring your- self and others.


AIC1116


WARNING


2-14 Instruments and controls


Z X


Passing signal Pulling the lever toward you turns on the headlight high beam. Turn signal Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signal cancels automatically. Lane change signal To indicate a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch.


FRONT FOG LIGHT SWITCH (if so equipped)


AIC0618


position.


To turn the front fog lights on, rotate the switch to the To turn them off, rotate the switch to the OFF position. The headlight switch must be in the position (low beam headlights on) for the fog lights to operate. The fog lights automatically turn off whenever the high beam headlight function is selected.


Instruments and controls 2-15


Z X


WINDSHIELD WIPER AND WASHER SWITCH


The ignition switch must be in the ON position for the wipers or washer to be activated. Push the lever down to operate the wipers, and pull the lever toward you to operate the washer. Operating the washer automatically cycles the wipers several times. Intermittent wiper operation can be adjusted from 1 to 19 seconds by turning the time control knob (Type B only).


CAUTION


O Do not operate the washer continu-


ously for more than 30 seconds.


O Do not operate the washer if the


reservoir tank is empty.


O Do not fill the window washer reser- voir tank with washer fluid concen- trates at full strength. Some methyl alcohol based washer fluid concen- trates may permanently stain the grille if spilled while filling the win- dow washer reservoir tank.


AIC1118


O Pre-mix washer fluid concentrates with water to the manufacturer’s rec- ommended levels before pouring the fluid into the window washer reser- voir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.


WARNING


In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the wind- shield with the defroster before you wash the windshield.


2-16 Instruments and controls


Z X


REAR WINDOW WIPER AND WASHER SWITCH (if so equipped)


INSTRUMENT BRIGHTNESS CONTROL


CAUTION


O Do not operate the washer continu-


ously for more than 30 seconds.


O Do not operate the washer if the


reservoir tank is empty.


WARNING


In freezing temperatures the washer solution may freeze on the window and obscure your vision. Warm the rear window with the defogger before you wash the rear window.


AIC1117


To operate the wiper, push the switch to the side. The wiper operates intermit-


tently. To operate the washer, push and hold the switch down to the side. The wiper will cycle twice.


AIC1023


The instrument brightness control operates when the light switch is in the or


position.


Turn the control to adjust the brightness of the instrument panel lights.


Instruments and controls 2-17


Z X


REAR WINDOW DEFOGGER SWITCH


HAZARD WARNING FLASHER SWITCH


AIC1004


SIC0050


Push the switch on to warn other drivers when you must stop or park under emer- gency conditions. All turn signal lights flash.


WARNING


O When stalled or stopped on the road- way under emergency conditions, move the vehicle well off the road.


To defog the rear window, start the engine and push the rear window defogger switch on. The rear window defogger indicator light on the switch comes on. Push the switch again to turn the defogger off. The rear window defogger automatically turns off after approximately 15 minutes.


CAUTION


When cleaning the inner side of the window, be careful not to scratch or damage the rear window defogger.


2-18 Instruments and controls


O Do not use the hazard warning flash- ers while moving on the highway unless unusual circumstances force you to drive so slowly that your ve- hicle might become a hazard to other traffic.


O Turn signals do not work when the hazard warning flasher lights are on.


The hazard warning flashers can be actu- ated with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving.


Z X


WARNING


The cigarette lighter should not be used while driving so full attention may be given to vehicle operation.


CAUTION


The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.


CIGARETTE LIGHTER (accessory) AND ASH TRAY


AIC1024


The cigarette lighter element is an acces- sory. A genuine NISSAN cigarette lighter or equivalent can be purchased from an autho- rized NISSAN dealer. The cigarette lighter operates when the ignition switch is in the ACC or ON position. Push the lighter in all the way. When the lighter is heated, it springs out. Return the lighter to its original position after use.


AIC1104


POWER POINT (if so equipped) The power point can be used for powering accessories. They are rated at 12 Volts 120
Watts maximum.


CAUTION


O Take care as the socket and plug may be hot during or immediately after use.


O This power point is not designed for


use with a cigarette lighter unit.


Instruments and controls 2-19


Z X


O Before inserting or disconnecting a plug, be sure to turn off the electrical accessory being used or the ACC power of the vehicle.


O Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may blow.


O When not in use, be sure to close the cap. Do not allow water to contact the socket.


STORAGE COMPARTMENT


A storage compartment center bottom of the instrument panel.


is located in the


AIC1103


Z X


AIC1105
O Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. O Use this power point with the engine running. (If the engine is stopped, this could result in a discharged bat- tery.)


O Avoid using when the air condi- tioner, headlights or rear window de- fogger is on.


2-20 Instruments and controls


TIE DOWN HOOKS


The tie down hooks can be used to secure cargo with ropes or other types of straps.


WARNING


O Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.


O Use suitable ropes and hooks to se-


cure cargo.


O Never allow anyone to ride in the luggage area. It is extremely danger- ous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.


O Do not allow people to ride in any is not area of your vehicle that equipped with seats and seat belts. O Be sure everyone in your vehicle is in a seat and using a seat belt prop- erly.


AIC1106


AIC1107


Do not apply a total load of more than 33
lbs (15kg) to a single hook when secur- ing cargo.


Instruments and controls 2-21


Z X


TONNEAU COVER


CUP HOLDER


AIC1119


The tonneau cover keeps the luggage com- partment contents hidden from the outside.


WARNING


O Never put anything on the tonneau cover, no matter how small. Any ob- ject on it could cause an injury in an accident or sudden stop.


O Do not leave the tonneau cover in the vehicle with it disengaged from the holder.


2-22 Instruments and controls


O Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.


WARNING


The cup holder should not be used while driving so full attention may be given to vehicle operation.


CAUTION


O Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liq- uid is hot, it can scald you or your passenger.


O Use only soft cups in the cup holder. Hard cups can injure you in an acci- dent.


Some cup holders have a rubber insert that can be removed for cleaning and for using larger cups.


Z X


MAP POCKETS


AIC1061


AIC1085


AIC1122


Map pockets are located on the side and back of the passenger seat. The map pocket can be used to store maps.


AIC1025


Instruments and controls 2-23


Z X


DOME LIGHT


MAP LIGHTS (if so equipped)


For information regarding dome light bulb replacement, refer to “Bulb replacement” in the ‘‘Do-it-yourself’’ section of this manual.


CAUTION


Leaving the dome light switch in the ON position for extended periods of time will result in a discharged battery.


IC1235M


The dome light has a three-position switch and operates regardless of ignition key position. O When the switch is in the OFF position, the dome light does not illuminate, re- gardless of door position.


O When the switch is in the center j or DOOR position, the dome light illumi- nates by opening a door.


O When the switch is in the ON position, the dome light illuminates regardless of door position.


2-24 Instruments and controls


AIC0704


To turn on the map lights push the switches. To turn them off, push the switches again.


CAUTION


Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.


Z X


ILLUMINATED ENTRY SYSTEM


The interior lights illuminate when a front, rear or the back door is opened. Once the doors are closed, these lights turn off in 30
seconds or turn off immediately when the key is turned to the ON position. Battery saver If the vehicle doors are not fully closed and the interior lights remain illuminated, they eventually turn off automatically to prevent the battery from becoming discharged. Inte- rior lights that illuminate when doors are opened turn off after approximately 30 min- utes.


MANUAL WINDOWS


POWER WINDOWS (if so equipped)


AIC0648


AIC1039


The side windows can be opened or closed by turning the hand crank on each door. To open a window on the driver side, turn the crank clockwise. To close a window, turn the crank counterclockwise. To open a window on the passenger side, turn the crank counterclockwise. To close a window, turn the crank clockwise.


WARNING


O Make sure that all passengers have their hands, etc. inside the vehicle before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.


O Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents.


Instruments and controls 2-25


Z X


lift


The power windows operate when the igni- tion key is in the ON position. To open the driver window, press the driver switch and hold it down. To close the win- dow, the switch up. The driver side control panel is equipped with switches to open or close all the windows. Locking passenger’s windows When the lock button is depressed, only the driver side window can be opened or closed. Push it in again to cancel the win- dow lock function.


2-26 Instruments and controls


AIC1028


AIC1110


Passenger power window switch The passenger switch opens or closes the passenger window. To open the window, press the switch and hold it down. To close the window, lift the switch up.


Rear power windows The rear power window switches open or close only the corresponding window. To open the window, push the switch and hold it down. To close the window, push the switch up.


Z X


SKYROOF (if so equipped)


AIC1121


AIC1111


AUTOMATIC POWER WINDOW SWITCH To fully open the driver window, completely press the driver window switch down and release it; it need not be held. To stop the window, lift the switch up while the window is opening.


Opening Pull the handle down, then push the handle up to the fully tilted position. The skyroof cannot be removed.


WARNING


In an accident you could be thrown from the vehicle through an open sky- roof. Always use seat belts and child restraints.


CAUTION


O Do not open skyroof when gear bas-


ket is in place.


O Always remove the gear basket be- fore opening skyroof. The skyroof may be scratched if it is opened with the gear basket in place. For instructions to remove the gear basket, refer to ‘‘Roof rack with gear basket’’ in the ‘‘Pre-driving checks and adjustments’’ section of this manual.


O Do not allow anyone to stand up or extend any portion of their body out of the skyroof opening while the ve- hicle is in motion.


O Remove water drops, snow, ice or sand from the skyroof before open- ing.


O Do not place heavy objects on the


skyroof or surrounding area.


Instruments and controls 2-27


Z X


Installing the sun shade 1. Insert the two hooks on the front edge of


sun shade into holders on the sunroof.


2. Align the two lock bolts on the rear edge of sun shade with the lock nuts. Turn each lock bolt clockwise to securely lock the sun shade in place.


AIC1112


AIC1083


Closing Pull the handle forward to unlock, then push the handle up completely to lock the skyroof closed.


WARNING


Do not remove or install the sun shade while driving so full attention may be given to vehicle operation.


Removing the sun shade 1. Turn each lock bolt counterclockwise


while supporting the sun shade.


2. Slide the shade backward to remove it.


2-28 Instruments and controls


Z X


3 Pre-driving checks and adjustments


Key .........................................................................3-2
Door locks ..............................................................3-2
Power door locks (if so equipped) .........................3-3
Child safety rear door lock.....................................3-4
Multi-remote control system (if so equipped).........3-4
Battery replacement ...............................................3-7
Illuminated entry system ........................................3-8
Hood release..........................................................3-9
Glove box ...............................................................3-9


Back door lock......................................................3-10
Roof rack with gear basket (if so equipped)........3-11
Step rail ................................................................3-13
Fuel filler cap........................................................3-14
Tilting steering wheel (if so equipped) .................3-15
Outside mirror remote control (if so equipped)....3-15
Outside mirrors.....................................................3-16
Inside mirror .........................................................3-17
Vanity mirror (if so equipped)...............................3-17


Z X


KEY


DOOR LOCKS


WARNING


O Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.


O Before opening any door, always look for and avoid oncoming traffic. O Do not leave children unattended in- side the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.


APD1025


A key number is supplied with your key. Record the key number and keep it in a safe place (such as your wallet), NOT IN THE VEHICLE. If you lose your keys, see an authorized NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by an authorized NISSAN dealer or locksmith.


3-2 Pre-driving checks and adjustments


APD1033


Locking doors with key To lock the door, turn the key towards the front of the vehicle. To unlock, turn it to- wards the rear. On power door lock equipped models, lock- ing the driver’s door simultaneously locks all doors.


Z X


AIC1012


APD1077


APD1014


Locking doors without key To lock the doors without the key, push the inside lock knob to the lock position, then close the door. When locking the door this way, be certain not to leave the key inside the vehicle.


POWER DOOR LOCKS (if so equipped) The power door lock system allows you to lock or unlock all doors simultaneously. Turning the key to the front of the vehicle locks all doors. Turning the key one time to the rear of the vehicle unlocks that door. From that posi- tion, returning the key to neutral (where the key can only be removed and inserted) and turning it to the rear again within 5 seconds unlocks all doors. The selective unlock func- tion and locking all doors can be operated from the driver, passenger, or back door.


To lock the doors without a key, push the door lock button (driver or passenger side) or the door lock knob (driver or passenger side), then close the door. When locking the doors this way, be certain not to leave the key inside the vehicle. If the key is in the ignition, all doors will unlock automatically.


Pre-driving checks and adjustments 3-3


Z X


MULTI-REMOTE CONTROL SYSTEM (if so equipped) It is possible to lock/unlock all doors and activate the panic alarm by using the remote controller. Be sure to remove the key from the vehicle before locking the doors. The remote controller can operate at a distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends on the conditions around the vehicle. As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact an authorized NISSAN dealer.


CAUTION


Listed below are conditions or occur- rences which will damage the remote controller: O Do not allow the remote controller to


become wet.


O Do not drop the remote controller.


APD1078


CHILD SAFETY REAR DOOR LOCK Child safety locks help prevent the rear doors from being opened accidentally, es- pecially when small children are in the ve- hicle. The child safety lock levers are located on the edge of the rear doors. When the lever is in the lock position, the door can only be opened from the out- side.


3-4 Pre-driving checks and adjustments


O Do not strike the remote controller


sharply against another object.


O Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).


Locking doors 1. Close all windows. 2. Remove the key from the ignition switch. 3. Close the hood and all the doors. 4. Push the


button on the multi-remote controller. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. The horn may or may not beep once. Refer to “Silencing the horn beep feature” later in this section.


O When the


button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder the doors are already locked.


that


O If a door is open and you push the lock but the


button, the doors will


Z X


2. Push the


button on the multi- remote controller again within five sec- onds. All doors unlock.


3. The interior lights illuminate for 30 sec- onds when the interior light switch is in the O or DOOR position.


The interior lights can be turned off without waiting 30 seconds by inserting the key into the ignition or locking the doors with the multi-remote controller or pushing the interior light switch to the OFF position. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the panic alarm to call attention as follows: 1. Push the


button on the remote con-


troller for longer than 1.5 seconds.


2. The theft warning alarm and headlights


will stay on for 30 seconds.


APD1079


horn will not beep and the hazard lights will not flash.


Unlocking doors 1. Push the


button on the multi- remote controller. Only the driver’s side door unlocks.


3. The panic alarm stops when: O it has run for 30 seconds, or O the


button is pressed, on the multi-remote controller.


the


or


Pre-driving checks and adjustments 3-5


Z X


The hazard lights will quickly flash three times to confirm that the horn beep feature has been reactivated. Deactivating the horn feature does not si- lence the horn if the alarm is triggered.


AIC1037


Silencing the horn beep feature If desired, the horn beep feature can be deactivated using the multi-remote control- ler. To deactivate: Press and hold the


and


together for at least two seconds.


The hazard lights will quickly flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the


and together for at least two seconds


once more.


3-6 Pre-driving checks and adjustments


Z X


BATTERY REPLACEMENT


Replace the battery in the multi-remote con- troller as follows: 1. Open the lid using a coin. 2. Replace the battery with a new one. Recommended battery: Sanyo CR2025


or equivalent.


3. Close the lid securely.


APD1087


4. Press the


button, then the


button two or three times to check the multi- remote controller operation.


If the battery is removed for any reason other than replacement, perform step 4
above. O An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. O The multi-remote controller is water- resistant; however, if it does get wet, immediately wipe completely dry.


O The operational range of the multi- remote controller extends to approxi- mately 33 ft (10 m) from the vehicle. This range may vary with conditions.


FCC Notice: Changes or modifications not expressly approved by the manufacturer for com- pliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this


Pre-driving checks and adjustments 3-7


Z X


device must accept any interference re- ceived including interference that may cause undesired operation of the device.


ILLUMINATED ENTRY SYSTEM


The interior lights illuminate when a front, rear or the back door is opened. Once the doors are closed, these lights turn off in 30
seconds or turn off immediately when the key is turned to the ON position. Battery saver If the vehicle doors are not fully closed and the interior lights remain illuminated, they eventually turn off automatically to prevent the battery from becoming discharged. Inte- rior lights that illuminate when doors are opened turn off after approximately 30 min- utes.


3-8 Pre-driving checks and adjustments


Z X


HOOD RELEASE


GLOVE BOX


APD1080


APD0601


WARNING


O Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.


O If you see steam or smoke coming to


from the engine compartment, avoid injury do not open the hood.


1. Pull the hood lock release handle located below the driver side instrument panel; the hood then springs up slightly.


2. Lift the lever at the front of the hood with


your fingertips and raise the hood.


3. Insert the support rod into the slot in the


front edge of the hood.


4. When closing the hood, reset the support rod to its original position, lower the hood to approximately 12 inches (30.5 cm) above the latch and release it. This al- lows proper engagement of the hood latch.


Open the glove box by pulling the handle.


WARNING


Keep glove box lid closed while driving to prevent injury in an accident or a sudden stop.


Pre-driving checks and adjustments 3-9


Z X


BACK DOOR LOCK


APD1081
O Do not drive with the back door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “Starting and driving” section for exhaust gas.


To unlock the back door turn the key clock- wise. To open the back door lift up on the door handle and lift the door up. To close, lower and push the door down securely. To lock the back door, turn the key counter- clockwise.


WARNING


O Always be sure the back door has been closed securely to prevent it from opening while driving.


3-10 Pre-driving checks and adjustments


Z X


ROOF RACK WITH GEAR BASKET (if so equipped)


Always evenly distribute cargo on the roof rack. The maximum total load is 125 lb (57 kg) evenly distributed, including gear basket. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Ratings


(GAWR front and rear). The GVWR and GAWR are located on the Safety Compli- ance Certification Label (located on the driver’s side door jamb pillar). For more information regarding GVWR and GAWR, refer to the “Technical and customer infor-


AIC1109


mation” section of this manual. WARNING


Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.


CAUTION


Use care when placing or removing items from the roof rack or gear basket. If you cannot comfortably lift the items onto the roof rack or gear basket from the ground, use a ladder or stool.


Pre-driving checks and adjustments 3-11


Z X


ACE1051


Getting the roof rack torxdriver 1. Open the back door. 2. Roll back the cargo area carpet. 3. Remove the roof rack torxdriver.


3-12 Pre-driving checks and adjustments


The front and rear crossbars can be ad- justed forward, backward, or be removed. Use the torxdriver located in the tool kit to loosen both crossbar adjusting screws. Position the crossbar as needed and then tighten the crossbar adjusting screws. Place


AIC1146


your cargo between the bars, and secure with rope. Always check the tightness of the cross bar adjusting screws.


Z X


STEP RAIL


APD1092


The roof rack is equipped with a removable gear basket. The maximum gear basket load is 30 lb (13.6 kg) evenly distributed. The gear basket can be removed by un- screwing the four hold down bolts.


The step rail has a front and rear step for assisting passengers to get into and out of the vehicle.


APD1088


Pre-driving checks and adjustments 3-13


Z X


FUEL FILLER CAP


APD1082


The fuel filler cap is a screw-on ratcheting type. Turn the cap counter clockwise to remove. Tighten the cap clockwise until ratcheting clicks are heard.


WARNING


O Gasoline is extremely flammable and highly explosive under certain con- ditions. You could be burned or se- riously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.


3-14 Pre-driving checks and adjustments


O Fuel may be under pressure. Turn the cap one-half turn and wait for any ‘‘hissing’’ sound to stop to pre- from spraying out and vent causing possible personal injury. Then remove the cap.


fuel


O Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refuel- ing may cause fuel overflow, result- ing in fuel spray and possibly fire.


O Use only an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An in- correct cap can result in a serious malfunction and possible injury.


O Never pour fuel into the throttle body


to attempt to start your vehicle.


CAUTION


O If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.


O Tighten until the fuel filler cap clicks. Failure to tighten the fuel filler cap properly may cause the mal- function indicator lamp (MIL) to illu- minate. If the lamp illuminates because the fuel filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few driving trips. If the lamp does not turn off after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.


O For additional information, see the (Malfunction indicator lamp (MIL)( in the (Instruments and Controls( sec- tion earlier in this manual.


Z X


TILTING STEERING WHEEL (if so equipped)


OUTSIDE MIRROR REMOTE CONTROL (if so equipped)


APD1083


PD1238M


APD1039


Put the fuel filler cap in the cap holder while refueling.


the lock lever down and adjust


Tilt operation Pull the steering wheel up or down to the desired position. Push the lock lever up firmly to lock the steering wheel in place.


WARNING


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


the right or left side mirror,


Push the right or left side of the switch to adjust then control the lever. The ignition switch must be in the ON or ACC position for the power mirrors to oper- ate.


Pre-driving checks and adjustments 3-15


Z X


OUTSIDE MIRRORS


WARNING


Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.


APD1090


APD1096


3-16 Pre-driving checks and adjustments


Z X


INSIDE MIRROR


VANITY MIRROR (if so equipped)


APD1097


AIC0703


AIC0710


Folding outside mirror Push the mirror backward to fold it.


The night position reduces glare from the headlights of vehicles behind you.


A vanity mirror is located on the rear side of the passenger sunvisor.


WARNING


Use the night position only when nec- essary because it reduces rear view clarity.


Pre-driving checks and adjustments 3-17


Z X


MEMO


3-18 Pre-driving checks and adjustments


Z X


4 Heater, air conditioner and audio systems


Ventilators...............................................................4-2
Heater and air conditioner......................................4-3
Controls ..................................................................4-3
Heater operation ....................................................4-4
Air conditioner operation (if so equipped)..............4-5
Air flow charts.........................................................4-6
Audio system........................................................4-10
AM-FM radio with cassette player .......................4-10
Cassette tape operation.......................................4-13
FM-AM radio with compact disc (CD) player (if so equipped) ....................................................4-15
Compat disc CD player operation........................4-19


CD care and cleaning ..........................................4-20
AM-FM radio with compact disc player (if so equipped) ....................................................4-22
Compact disc (CD) player operation....................4-25
CD care and cleaning ..........................................4-26
AM-FM radio with cassette player and compact disc player (if so equipped)...................4-28
Cassette tape operation.......................................4-32
Compact disc (CD) player operation....................4-33
CD care and cleaning ..........................................4-35
Antenna ................................................................4-35
Car phone or CB radio.........................................4-36


Z X


VENTILATORS


Adjust air flow direction by moving the ven- tilators slides and ventilator assemblies.


AHA1099


4-2 Heater, air conditioner and audio systems


Z X


HEATER AND AIR CONDITIONER


WARNING


O The air conditioner cooling function operates only when the engine is running. O Do not


leave children, unreliable adults, or pets alone in your vehicle. On hot sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.


O Do not use the recirculation mode for long periods as it may cause the


Air control dial This dial allows you to select the air flow outlets.


— Air flows from center and side


ventilators.


— Air flows from center and side ventilators and the front and rear floor outlets.


— Air flows mainly from the front and


rear floor outlets.


— Air flows from defrost outlets and


the front and rear floor outlets.


— Air flows mainly from defrost outlets.


Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air.


Air recirculation button (if so equipped)


NOTE: The air recirculation feature is available only on those vehicles equipped with air conditioning.


AHA1151


interior air to become stale and the windows to fog up.


O Positioning of the heater or air con- ditioner controls should not be done while driving, in order that full atten- tion may be given to the driving operation.


CONTROLS Fan control dial This dial controls fan speed.


turns the fan on and off, and


Heater, air conditioner and audio systems 4-3


Z X


OFF position (indicator light off): Outside air is drawn into the passenger compartment and distributed through the selected outlets. Use the OFF position for normal heater or air conditioner operation. ON position (indicator light on): Interior air is recirculated inside the vehicle. Push the button to the on position when: O driving on a dusty road. O to prevent traffic fumes from entering the


passenger compartment.


O for maximum cooling when using the air


conditioner.


The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct most of the hot air to the front and rear floor outlets. Rear passenger heat is provided by the front system through floor outlets located under both front seats. A small amount of air also flows from the defrost outlets. 1. Push the


button (if so equipped) to


the off position for normal heating.


2. Turn the air control dial to the


sition.


po-


3. Turn the fan control dial to the desired


position.


2. Turn the air control dial to the


po-


sition.


3. Turn the fan control dial to the desired


position.


4. Turn the temperature control dial to the


desired position.


Defrosting/defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air control dial to the


posi-


tion.


2. Turn the fan control dial to the desired


position.


3. Turn the temperature control dial to the


desired position.


Air conditioner button (if so equipped) Start the engine, move the fan control dial to the desired (one to four) position, and push the air conditioner button to turn on the air conditioner. The indicator light comes on when the air conditioner is operating. To turn off the air conditioner, push the button again. 4-4 Heater, air conditioner and audio systems


4. Turn the temperature control dial to the desired position between the middle and the hot position.


Ventilation This mode directs outside air from the side and center vents. 1. Push the


button (if so equipped) to


the off position.


temperature


When the position is selected, the air conditioner automatically turns on (however the indicator light will not illuminate) if the outside than 45°F(7°C). This dehumidifies the air which helps The mode automatically turns off, allow- ing outside air to be drawn into the passen- ger compartment to further improve the defogging performance.


windshield.


is more


defog


the


Z X


Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets. 1. Push the


button (if so equipped) to


the off position.


2. Turn the air control dial to the


posi-


tion.


3. Turn the fan control dial to the desired


position.


4. Turn the temperature control dial to the


the desired position.


Heating and defrosting/defogging This mode directs a portion of the air to the defrost outlets to defrost/defog the win- dows, and also directs air to the front and rear floor outlets to heat the cabin. 1. Turn the air control dial to the


po-


sition.


2. Turn the fan control dial to the desired


position.


3. Turn the temperature control dial to the desired position between the middle and the hot position.


position is selected, the air When the conditioner automatically turns on (however the indicator light will not illuminate) if the outside temperature is more than 45°F (7°C). This dehumidifies the air which helps mode au- defog the windshield. The tomaticallly turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging perfor- mance. Operating tips Clear snow and ice from the wiper blades and air inlet in front of the wind- shield. This improves heater operation. AIR CONDITIONER OPERATION (if so equipped) Start the engine, move the fan control dial to the desired (one to four) position, and push in the air conditioner button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function op- erates only when the engine is running.


Cooling This mode directs cooled and dryed air to the side and center vents to cool and dehu- midify the cabin. 1. Push the 2. Turn the air control dial to the


button to the off position. posi-


tion.


3. Turn the fan control dial to the desired


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Turn the temperature control dial to the


desired position.


For quick cooling when the outside tem- perature is high, push the button to the ON position. Be sure to return the air recir- culation button to the OFF position for nor- mal cooling. Dehumidified heating This mode directs warmed and dryed air to the front and rear floor outlets to heat and dehumidify the cabin. 1. Push the


button to the off position.


Heater, air conditioner and audio systems 4-5


Z X


2. Turn the air control dial to the


po-


sition.


3. Turn the fan control dial to the desired


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Turn the temperature control dial to the


desired position.


Dehumidified defrosting/defogging This mode directs warmed and dryed air to the defrost outlets to defrost/defog the win- dows. 1. Turn the air control dial to the


posi-


tion.


2. Turn the fan control dial to the desired


position.


3. Push on the air conditioner button. The


indicator light comes on.


4. Turn the temperature control dial to the


desired position.


AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recir- culation switch should always be in the OFF position for heating and defrosting.


perature is more than 45°F(7°C). This de- humidifies the air which helps defog the mode automatically windshield. The turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance. Operating tips O Keep windows and sunroof closed while


the air conditioner is in operation.


O After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.


O The air conditioning system should be operated for approximately ten min- utes at least once a month. This helps prevent damage to the system due to lack of lubrication.


When the or positions in be- tween are selected, the air conditioner au- tomatically turns on (however the indicator light will not illuminate) if the outside tem- 4-6 Heater, air conditioner and audio systems


O If


the engine coolant


temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See ‘‘If your vehicle overheats’’ in the ‘‘In case of emergency’’ section of this manual.


Z X


AHA1150


AHA1147
Heater, air conditioner and audio systems 4-7


Z X


4-8 Heater, air conditioner and audio systems


AHA1148


AHA1149


Z X


Servicing air conditioner The air conditioner system in your NISSAN is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants causes severe damage to your air conditioner system. See “Air conditioner system refrigerant and lubricant recommen- dations” in the ‘‘Technical and consumer information’’ section of this manual. An authorized NISSAN dealer will be able to service your environmentally ‘‘friendly’’ air conditioner system.


WARNING


The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done by an experienced technician with proper equipment.


AHA1134


Heater, air conditioner and audio systems 4-9


Z X


AUDIO SYSTEM


4-10 Heater, air conditioner and audio systems


AHA1004


AM-FM RADIO WITH CASSETTE PLAYER ONzOFF/VOL control knob Turn the ignition key to the ACC or ON position, then push the ONzOFF/VOL con- trol knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or cassette) which was playing immediately before the system was turned off resumes playing. When no cassette is loaded, the radio comes on. Pushing the ONzOFF/VOL con- trol knob again turns the system off. Turn the ONzOFF/VOL control knob to ad- just the volume. Clock operation Pressing the CLOCK button alternates the clock and the radio/cassette tape options in the display. Clock set Depressing the CLOCK and the buttons together sets hours. Depressing the CLOCK and


buttons together sets minutes.


Z X


Clock priority mode In this mode the clock is shown in the display. If any radio or cassette tape func- tions are activated, the radio (or cassette tape) display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. Radio/Cassette tape priority mode In this mode, the radio station illuminates in the display during radio operation. During cassette tape operation, TAPE illuminates in the display. Selecting the desired band Push the to FM1 or FM2 reception. The FM stereo indicator, ST, illuminates dur- ing FM stereo reception. When the stereo broadcast signal is weak, the radio automati- cally changes from stereo to monaural re- ception. Radio reception is affected by station signal strength, distance from radio transmitter,


button to change from AM


influences.


buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. TUNE buttons


SCAN tuning Push and hold the


tuning button for more than 1.5 seconds. SCAN illu- minates in the display window. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.


WARNING


The radio should not be tuned while driving so full attention may be given to vehicle operation.


and


Use the buttons for manual tuning. To move quickly through the channels, hold either of the tune buttons down for more than 1.5 seconds. SEEK tuning Push the for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station. Pushing the button again continues the SEEK function. Once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcast station.


tuning button


Heater, air conditioner and audio systems 4-11


Z X


FM2. The selected band illuminates in the display.


2. Tune to the desired station. 3. Push the desired station select button for more than 2 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.


4. When the sound resumes, memorizing is


complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired sta- tions.


AHA1045


Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push 4-12 Heater, air conditioner and audio systems


to select AM, FM1, or


AHA1027


Adjusting tone quality and speaker balance To adjust BASSzTREBzFADERzBAL (Bass, Treble, Fader, Balance), press the AUDIO button until the desired mode (BAS, TRE, FAD or BAL) appears in the display. Press the button to adjust Bass (BAS) and Treble (TRE) to the desired level. Use the button to adjust Fader or Balance modes. Fader (FAD) adjusts the sound level between the front and rear speakers and Balance (BAL) adjusts the


or


or


Loading...
x