2006 Nissan Murano Owners Manual

墌 05.8.26/Z50-D/V5.0 墍

AUTOMATIC DRIVE POSITIONER (if so equipped) The automatic drive positioner system has two features: 쐌 Entry/exit function 쐌 Memory storage ENTRY/EXIT FUNCTION This system is designed so that the driver’s seat and outside mirror will automatically move when the selector lever is in the P (Park) position. This allows the driver to get into and out of the driver’s seat more easily.

The driver’s seat will slide backward:

The driver’s seat will slide backward when the driver’s door is opened with the ignition switch (knob) in the LOCK position.

The driver’s seat will return to the previous position: 쐌 When the key is inserted into the ignition switch after closing the driver’s door, or when the driver’s door is closed after inserting the key into the ignition switch.

The entry/exit feature can be canceled. See “4. Display screen, heater, air conditioner and audio systems” section of this manual. The entry/exit function can be activated or can- celled by pressing and holding the SET switch for more than 10 seconds while the ignition key is in the LOCK position. The indicator light will blink once when the function is cancelled, and light will blink twice when the the indicator function is activated. the battery cable is disconnected, or if the fuse opens, the entry/exit function will be cancelled. In such a case, after connecting the battery or replacing with a new fuse, open and close the driver’s door more than two times with the ignition key or ignition switch in the LOCK position to activate the entry/exit function.

If

쐌 When the ignition switch is pushed with the (Intelligent Key

closed.

driver’s equipped model)

door

쐌 When the key or ignition switch is turned to

the ON position.

SPA2185

MEMORY STORAGE Two positions for the driver’s seat, pedals (Brake and Accelerator) and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory system.

1. Set the selector lever to the P (Park) position.

2. Adjust the driver’s seat, pedals (Brake and Accelerator) and outside mirrors to the de- sired positions by manually operating each adjusting switch. For additional information, see “Seats” in the “1. Safety — seats, seat belts and supplemental restraint system” Pre-driving checks and adjustments 3-33

墌 05.8.26/Z50-D/V5.0 墍

section and “Pedal position adjustment” and “Outside mirrors” earlier in this section.

3. Turn the ignition ON.

4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second.

The indicator light for the pushed memory switch will come on and stay on for approxi- mately 5 seconds after pushing the switch. After the indicator light goes off, the selected positions are stored in the selected memory (1 or 2).

If memory is stored in the same memory switch, the previous memory will be deleted. Linking a remote keyless entry to a stored memory position A remote keyless entry can be linked to a stored memory position with the following procedure. 1. Follow the steps for storing a memory posi-

tion.

for

light

2. While the indicator

the memory switch being set is illuminated for 5 seconds, push the unlock button on the remote keyless entry. The indicator light will blink. After the indicator light goes off, the remote keyless entry is linked to that memory setting.

3-34 Pre-driving checks and adjustments

With the key removed from the ignition switch, push the unlock button on the keyfob. The driver’s seat, pedals (Brake and Accelerator) and outside mirrors will move to the memorized position. Confirming memory storage 쐌 Turn the ignition switch to the ON position and push the SET switch. If the main memory has not been stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indicator light will stay on for approxi- mately 5 seconds.

Selecting the memorized position 1. Set the sift selector lever to the P (Park)

position.

2. Turn the ignition ON. 3. Push the memory switch (1 or 2) fully for at

least 1 second. The driver’s seat, pedals (Brake and Accel- erator) and outside mirrors will move to the memorized position with the indicator light flashing, and then the light will stay on for approximately 5 seconds. SYSTEM OPERATION The automatic drive positioner system will not

work or will stop operating under the following conditions: 쐌 when the vehicle speed is above 4 MPH (7

km/h).

쐌 when any two or more of

the memory switches and the SET switch is simulta- neously pushed while the automatic drive positioner is operating.

쐌 when the adjusting switch for the driver’s seat, pedals and outside mirror are operated while the automatic drive positioner is oper- ating.

쐌 when the memory switch (1 or 2) and the least 1

SET switch is not pushed for at second.

쐌 when the seat has been already moved to the

memorized position.

쐌 when no seat position is stored in the

memory switch.

쐌 when the engine is started while moving the

automatic drive positioner.

쐌 when the shift selector lever is moved from the P position to any other position (However, it will not be cancelled if the switch is pushed while the seat is returning to the previous positions (entry/exit function).).

墌 05.8.26/Z50-D/V5.0 墍

MEMO

Pre-driving checks and adjustments 3-35

墌 05.8.26/Z50-D/V5.0 墍

MEMO

3-36 Pre-driving checks and adjustments

墌 05.8.26/Z50-D/V5.0 墍

4 Display screen, heater, air conditioner and

audio systems

Safety note .............................................................................. 4-2
Control panel buttons — without navigation system.... 4-2
How to use joystick and “ENTER” button................. 4-3
How to use “BACK” button .......................................... 4-3
How to use “TRIP” button............................................. 4-3
How to use “FUEL ECON” button.............................. 4-3
Clock ................................................................................... 4-4
How to use “E/M” button .............................................. 4-4
How to use “MAINT” (Maintenance) button ............. 4-4
Maintenance notice ......................................................... 4-5
How to use “SETTING” button .................................... 4-6
“DAY/NIGHT” button.................................................... 4-10
Control panel buttons — with navigation system ....... 4-11
How to use joystick and “ENTER” button .............. 4-11
How to use “BACK” button........................................ 4-11
Setting up the start-up screen................................... 4-12
How to use the “TRIP” button ................................... 4-12
Maintenance notice....................................................... 4-14
How to use the “SETTING” button .......................... 4-15
“DAY/NIGHT” button.................................................... 4-19
Rear view monitor (if so equipped) ................................ 4-19
How to read the displayed lines................................ 4-20

Rear view monitor setting............................................ 4-20
Operating tips................................................................. 4-20
Ventilators.............................................................................. 4-21
Heater and air conditioner (Automatic) ......................... 4-23
Automatic operation...................................................... 4-24
Manual operation ........................................................... 4-25
Operating tips................................................................. 4-25
In-cabin microfilter......................................................... 4-26
Servicing air conditioner.................................................... 4-26
Audio system ........................................................................ 4-27
FM radio reception........................................................ 4-27
AM radio reception ....................................................... 4-28
Satellite radio reception............................................... 4-28
Audio operation precautions....................................... 4-28
FM-AM-SAT radio with CD player .......................... 4-33
FM-AM-SAT radio with cassette player and CD changer ............................................................................ 4-37
CD care and cleaning .................................................. 4-42
Steering switch for audio control (if so equipped)......................................................................... 4-43
Antenna ............................................................................ 4-44
Car phone or CB radio .................................................... 4-44

墌 05.8.26/Z50-D/V5.0 墍

SAFETY NOTE

CONTROL PANEL BUTTONS — WITHOUT NAVIGATION SYSTEM

WARNING

쐌 Positioning of the heating or air con- ditioning controls and display con- trols should not be done while driv- ing, in order that full attention may be given to the driving operation.

쐌 Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock.

쐌 Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in acci- dent, fire or electric shock.

쐌 In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell com- ing from it, stop using the system immediately and contact a NISSAN dealer. Ignoring such conditions may lead to accidents, fire, or electrical shock.

1. “TRIP” button

2. “FUEL ECON” button

3. Clock adjust button

4. “TRIP RESET” button

SAA1352

5. “E/M” button

6. “DAY/NIGHT” button

7. “BACK” button

8. JOYSTICK and “ENTER” button

4-2 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

9. “SETTING” button 10. “MAINT” maintenance button Make sure the engine is running before using this system. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick. Push the “ENTER” button only when the use of it is instructed on the display. HOW TO USE “BACK” BUTTON Finish setup: If you push the “BACK” button after the setup is completed, the display will return to the previous screen.

SAA1317

SAA1318

HOW TO USE “TRIP” BUTTON When the “TRIP” button is pushed, the following modes will display on the screen. TRIP 1 (TIME, DIST, AVG) → TRIP 2 (TIME, DIST, AVG) → OFF Elapsed Time, Driving Distance and Average Speed will be displayed. To reset, select the “Reset” key using the joy- stick and push the “ENTER” button, or push the “TRIP RESET” or “TRIP” button for more than approximately 1.5 seconds.

HOW TO USE “FUEL ECON” BUTTON Average Fuel Economy and Distance to Empty will be displayed for reference when the “FUEL ECON” button is pushed. To reset, select the “Reset” key using the joy- stick and push the “ENTER” button, or push the “TRIP RESET” or “TRIP” button for more than approximately 1.5 seconds.

Display screen, heater, air conditioner and audio systems 4-3

墌 05.8.26/Z50-D/V5.0 墍

To finish the adjusting, push the “BACK” button or the screen will return to normal after 10
seconds. The clock can be adjusted on the setting display. See the “HOW TO USE “SETTING” BUTTON” later in this section. HOW TO USE “E/M” BUTTON You can change the unit as follows using the “E/M” (English/Metric) button. Unit: US — Mile, °F, MPG

Metric — km, °C, L/100 km

SAA1353

CLOCK The digital clock displays time when the ignition switch is in ACC or ON. If the battery cable is disconnected, the clock will not indicate the correct time. Readjust the time. Adjusting the time To adjust the time, push the “H” or “M” button for more than approximately 1.5 seconds. The time indicator will flash. Push the H button to adjust the hour. Push the M button to adjust the minute. 4-4 Display screen, heater, air conditioner and audio systems

SAA1319

HOW TO USE “MAINT” (Maintenance) BUTTON Maintenance and tire pressure information (if so equipped) will be displayed when the “MAINT” button is pushed.

To display the setting of the maintenance inter- val, select the “Engine Oil” or “Tire Rotation” key using the joystick and push the “ENTER” button.

the maintenance interval, select

To set the “Maintenance Schedule” key by using the joy- stick and move the joystick to the right or left.

To reset the maintenance interval, select the

墌 05.8.26/Z50-D/V5.0 墍

The “MAINTENANCE NOTICE” screen displays each time the key is turned ON until one of the following conditions are met: 쐌 “RESET” is selected. 쐌 “Display Maintenance Notification” is set

OFF.

쐌 the maintenance interval is set again.

SAA1320

SAA1354

“Reset” key using the joystick and push the “ENTER” button. To display the MAINTENANCE NOTICE, auto- matically when setting trip distance is reached, select the “Display Maintenance Notification” key and push the “ENTER” button.

MAINTENANCE NOTICE The “MAINTENANCE NOTICE” screen (“EN- GINE OIL” or “TIRE ROTATION”) will be auto- matically displayed as shown when both of the following conditions are met: 쐌 the vehicle is driven the set distance and the

ignition switch is turned OFF.

쐌 the ignition key is turned ON the next time the

vehicle will be driven.

To return to the previous display after the “MAINTENANCE NOTICE” screen is displayed, push the “PREV” button.

Display screen, heater, air conditioner and audio systems 4-5

墌 05.8.26/Z50-D/V5.0 墍

TIRE or CHECK ALL TIRE) is displayed on the screen: FLAT TIRE — low tire pressure.

WARNING

쐌 When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the TPMS.

the proper operation of

SAA1321

Tire pressure information (if so equipped) Pressure indication in ** psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly. The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of low tire pressure, a message (FLAT 4-6 Display screen, heater, air conditioner and audio systems

SAA1355

HOW TO USE “SETTING” BUTTON The SETTINGS screen will appear when the “SETTING” button is pushed.

墌 05.8.26/Z50-D/V5.0 墍

Display Off: To turn off the screen, push the “SETTING” button and select the “Display” key and “Display Off” key. The indicator of the “Display Off” will turn on. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5
seconds after the operation is finished. To turn on the screen, push the “SETTING” button and select the “Display” key and “Display Off” key, then set the screen to on by pushing the “ENTER” button. Setting Audio or HVAC display: Choose the “Audio” or “HVAC” (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC (heater, air conditioner) setting condition will normally appear on the screen. To return to the setting screen, push the “SETTING” button or “BACK” button.

SAA1356

“Display” settings The DISPLAY SETTINGS screen will appear when selecting the “Display” key and pushing the “ENTER” button. Brightness/Contrast/Screen Background: To adjust the brightness and contrast of the screen, select the “Brightness/Contrast/Screen Background” key and push the “ENTER” button. Then you can adjust the brightness to Darker or Brighter, the contrast to Lower or Higher using the joystick.

SAA1357

Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the “Vehicle Elec- tronic Systems” key with the joystick and push- ing the “ENTER” button. You can set operating conditions. To set an operating condition, select the appli- cable item using the joystick, and push the “ENTER” button. The indicator light alternately turns on and off each time the “ENTER” button is pushed. Indicator light is illuminated. — ON

the various electronic systems

Display screen, heater, air conditioner and audio systems 4-7

墌 05.8.26/Z50-D/V5.0 墍

the Intelligent Key to return to the previ- ous mode.

Auto Re-Lock Time:

The length of the auto door re-lock time can be set. Select the “Auto Re-Lock Time” key, then move the joystick and push the ENTER button to adjust the time. Sensitivity of Automatic Headlights:

Automatic light illumination can be set as de- sired.

Select the “Sensitivity of Automatic Headlights” key, then move the joystick to the left (lower) or right (higher). Automatic Headlights Off Delay:

You can control how long it takes the automatic turn off timer to extinguish the headlights in the AUTO position.

Select the “Automatic Headlights Off Delay” key, then move the joystick to the left or right to adjust the timer. Intelligent Key Lock Response — Sound (if so equipped):

The sound pattern of the Intelligent request switch operation can be set as desired. Select the “Intelligent Key lock response — Sound” key,

SAA1358

SAA1389

Indicator light is not illuminated. — OFF Adjust driver seat when exiting vehicle: The driver’s seat automatically moves back and returns to the original position for ease of exit and entry. Selective door unlock: This key can switch the unlock doors of the 1st unlocking operation as follows: ON (Only the driver side door) ←→ OFF (All the doors)

Keyless Remote Response — Horn*:

This key changes the horn chirp mode that occurs when pushing the LOCK button on the keyfob or the Intelligent Key. Keyless Remote Response — Lights*:

This key changes the hazard indicator flash mode that occurs when pushing the LOCK or UNLOCK button on the keyfob or the Intelligent Key. * Even if you change the horn chirp or the hazard flash with the keyfob or the Intel- ligent Key, the change may not be re- flected in the display. Use the keyfob or

4-8 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

then push the ENTER button to change the sound pattern. Intelligent Key Unlock Response — Beep Sound (if so equipped): The beep sounds when unlocking door with the Intelligent request switch can be turned on or off. Return All Settings to Default: When this key is selected and turned on using the “ENTER” button, all settings made by VEHICLE ELECTRONICS will return to the initial conditions.

SAA1327

SAA1353

System settings Language/Unit: The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pushing the “ENTER” button. Language: English or French Unit: US — Mile, °F, MPG

Metric — km, °C, L/100 km

You can select the language and unit using the joystick and “ENTER” button.

Clock: Adjusting the time Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time. The time will change step by step. After completion of the setting, push the “BACK” button.

Display screen, heater, air conditioner and audio systems 4-9

墌 05.8.26/Z50-D/V5.0 墍

“DAY/NIGHT” BUTTON To change the display brightness, push the “DAY/NIGHT” button. Pushing the button again will change the display to DAY or NIGHT dis- play. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the “BACK” button is pushed, the display will return to the previous display. Pushing the “DAY/NIGHT” button for more than approximately 1.5 seconds will turn the display off. The screen will change to “CONFIRM DIS- PLAY OFF YES or NO”.

4-10 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

CONTROL PANEL BUTTONS — WITH NAVIGATION SYSTEM

1. “DAY/NIGHT” button 2. “BACK” button 3. Joystick and “ENTER” button 4. “SETTING” button 5. “TRIP” button 쎻A : For Navigation system control buttons; refer to the separate Navigation System Owner’s Manual.

When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick and push the “ENTER” button for operation. HOW TO USE “BACK” BUTTON This has two functions. 쐌 Go back to the previous display (cancel). If you push the “BACK” button during setup, the setup will be canceled and/or the display will return to the previous screen.

SAA1316

Display screen, heater, air conditioner and audio systems 4-11

墌 05.8.26/Z50-D/V5.0 墍

HOW TO USE THE “TRIP” BUTTON When the “TRIP” button is pushed, the following modes will display on the screen. Warning message (if there are any) → TRIP 1 → TRIP 2 → FUEL ECONOMY → MAINTE- NANCE.

쐌 Finish setup. If you push the “BACK” button after the setup is completed, the setup will start over, and the display will return to the climate control or Audio mode, and Navigation screen. SETTING UP THE START-UP SCREEN When you turn the ignition switch to ACC, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the “I AGREE” (English) or “ENTER” (Franc¸ ais) key then push the “ENTER” button. If you do not push the “ENTER” button, this system will not proceed to the next step display. If you do not push the button or select the screen key for more than 1 minute on the TRIP, SETTING or START-UP screen, the screen will change to TRIP screen automatically. To proceed to the next step, refer to the separate Navigation System Owner’s Manual.

SAA1317

“TRIP” information Elapsed Time, Driving Distance and Average Speed will be displayed. To reset, select the “Reset” key using the joy- stick and push the “ENTER” button or push the “TRIP” button for more than approximately 1.5
seconds.

4-12 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

SAA1318

SAA1319

SAA1320

“FUEL ECONOMY” information Average Fuel Economy and Distance to Empty will be displayed for reference. To reset, select the “Reset” key using the joy- stick and push the “ENTER” button or push the “TRIP” button for more than approximately 1.5
seconds.

“MAINTENANCE” information You can set the engine oil and the tire rotation interval. And the tire pressure will appear on the screen (if the tire pressure system is equipped). To display the setting of the maintenance inter- val, select the “Engine Oil” or “Tire Rotation” key using the joystick and push the “ENTER” button.

the maintenance interval, select

the To set “Maintenance Schedule” key by using the joy- stick and move the joystick to the right or left. To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button. To display the MAINTENANCE NOTICE, auto- matically when setting trip distance is reached, select the “Display Maintenance Notification” key and push the “ENTER” button.

Display screen, heater, air conditioner and audio systems 4-13

墌 05.8.26/Z50-D/V5.0 墍

The “MAINTENANCE NOTICE” screen displays each time the key is turned ON until one of the following conditions are met: 쐌 “RESET” is selected. 쐌 “Display Maintenance Notification” is set

OFF.

쐌 the maintenance interval is set again.

SAA1354

MAINTENANCE NOTICE The “MAINTENANCE NOTICE” screen (“EN- GINE OIL” or “TIRE ROTATION”) will be auto- matically displayed as shown when both of the following conditions are met: 쐌 the vehicle is driven the set distance and the

ignition switch is turned OFF.

쐌 the ignition key is turned ON the next time the

vehicle will be driven.

To return to the previous display after the “MAINTENANCE NOTICE” screen is displayed, push the “BACK” button.

4-14 Display screen, heater, air conditioner and audio systems

SAA1321

Tire pressure information (if so equipped) To view “TIRE PRESSURE” information, push the “TRIP” button repeatedly until the “MAINTE- NANCE” screen is displayed. Select “TIRE PRESSURE” using the joystick and push the “ENTER” button.

Pressure indication in ** psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual

墌 05.8.26/Z50-D/V5.0 墍

order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of displayed on the screen: FLAT TIRE — low tire air pressure.

low tire pressure, a message is

WARNING

쐌 When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

쐌 Replacing tires with those not origi- nally specified by NISSAN could af- fect the TPMS.

the proper operation of

SAA1322

SAA1323

* — Refer to the separate Navigation System Owner’s Manual. HOW TO USE THE “SETTING” BUTTON The SETTINGS screen will appear when the “SETTING” button is pushed.

“Display” settings The DISPLAY SETTINGS screen will appear when selecting the “Display” key and pushing the “ENTER” button. Brightness/Contrast/Map Background:

To adjust the brightness and contrast of the screen, select the “Brightness/Contrast/Map Background” key and push the “ENTER” button. Then you can adjust the brightness to Darker or Brighter, the contrast to Lower or Higher using the joystick.

The Map Background is related to the navigation

Display screen, heater, air conditioner and audio systems 4-15

墌 05.8.26/Z50-D/V5.0 墍

system. Refer to the separate Navigation System Owner’s Manual. Display Off: To turn off the screen, push the “SETTING” button and select the “Display” key and “Display Off” key. The indicator of the “Display Off” will turn on. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5
seconds after the operation is finished on the map display in the Audio, HVAC (Heater and air conditioner). To turn on the screen, push the “SETTING” button and select the “Display” key and “Display Off” key, then set the screen to on by pushing the “ENTER” button. Setting Audio or HVAC display: Choose the “Audio” or “HVAC” (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC (heater, air conditioner) setting condition will normally appear on the screen. To return to the setting screen, push the “SETTING” button or “BACK” button.

SAA1324

SAA1325

Indicator light is not illuminated. — OFF Selective door unlock: This key can switch the unlock doors of the 1st unlocking operation as follows: ON (Only the driver side door) ←→ OFF (All the doors)

Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the “Vehicle Elec- tronic Systems” key with the joystick and push- ing the “ENTER” button.

the various electronic systems

You can set operating conditions. To set an operating condition, select the appli- cable item using the joystick, and push the “ENTER” button. The indicator light alternately turns on and off each time the “ENTER” button is pushed. Indicator light is illuminated. — ON

4-16 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

then push the ENTER button to change the sound pattern. Intelligent Key Unlock Response — Beep Sound (if so equipped): The beep sounds when unlocking door with the Intelligent request switch can be turned on or off. Return All Settings to Default: When this key is selected and turned on using the “ENTER” button, all settings made by VEHICLE ELECTRONICS will return to the initial conditions.

the Intelligent Key to return to the previ- ous mode.

Auto Re-Lock Time:

The length of the auto door re-lock time can be set. Select the “Auto Re-Lock Time” key, then move the joystick and push the ENTER button to adjust the time. Sensitivity of Automatic Headlights:

Automatic light illumination can be set as de- sired.

Select the “Sensitivity of Automatic Headlights” key, then move the joystick to the left (lower) or right (higher). Automatic Headlights Off Delay:

You can control how long it takes the automatic turn off timer to extinguish the headlights in the AUTO position.

Select the “Automatic Headlights Off Delay” key, then move the joystick to the left or right to adjust the timer. Intelligent Key Lock Response — Sound (if so equipped):

The sound pattern of the Intelligent request switch operation can be set as desired. Select the “Intelligent Key lock response — Sound” key,

SAA1326

Keyless Remote Response — Horn*:

This key changes the horn chirp mode that occurs when pushing the LOCK button on the keyfob or the Intelligent Key. Keyless Remote Response — Lights*:

This key changes the hazard indicator flash mode that occurs when pushing the LOCK or UNLOCK button on the keyfob or the Intelligent Key. * Even if you change the horn chirp or the hazard flash with the keyfob or the Intel- ligent Key, the change may not be re- flected in the display. Use the keyfob or

Display screen, heater, air conditioner and audio systems 4-17

墌 05.8.26/Z50-D/V5.0 墍

ON: The displayed time advances by one hour. OFF: The current time is displayed. Adjusting the time to the GPS Select the “Auto Adjust” key. The time will be reset to the GPS time.

SAA1327

SAA1328

System settings Language/Unit: The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pushing the “ENTER” button. Language: English or French Unit: US — Mile, °F, MPG

Metric — km, °C, L/100 km

You can select the language and unit using the joystick and “ENTER” button.

Clock:

Adjusting the time

Select the “Hours” or “Minutes” key and move the joystick to the right or left to adjust the time.

The time will change step by step.

After completion of the setting, push the “BACK” button. Setting daylight saving time

Turn ON or OFF daylight saving time.

Every time the “Daylight Saving Time” key is selected, the light turns ON and OFF alternately.

4-18 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

쐌 “Newfoundland” zone After selection, the CLOCK SETTINGS screen will appear. The GPS time (manual time) corresponding to the selected zone will be displayed. “Pacific” zone has been set as the initial (default) setting. Beep setting: When Beep setting is on (indicator light on), a beep will sound if any audio button is pushed. “DAY/NIGHT” BUTTON To change the display brightness, push the “DAY/NIGHT” button. Pushing the button again will change the display to DAY or NIGHT dis- play. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the “BACK” button is pushed, the display will return to the previous display.

REAR VIEW MONITOR (if so equipped) When the selector lever is shifted into the R (Reverse) position, the monitor display shows view to the rear of the vehicle.

The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper and may not detect objects close to the bumper or on the ground.

WARNING

쐌 The rear view camera is a conve- nience but it is not a substitute for proper backing. Always turn and check that it is safe to do so before backing up. Always back up slowly. 쐌 Objects viewed in the rear view moni- tor differ from actual distance be- cause a wide-angle lens is used. Ob- jects in the rear view monitor will appear visually opposite like ones viewed in the inside and outside mir- rors.

쐌 Make sure that the lift gate is se-

curely closed when backing up.

Display screen, heater, air conditioner and audio systems 4-19

墌 05.8.26/Z50-D/V5.0 墍

SAA1329

Selecting the time zone

1. Select the “Select Time Zone” key.

The TIME ZONE screen will appear.

2. Select one of the following zones depending

on the current location.

쐌 “Pacific” zone 쐌 “Mountain” zone 쐌 “Central” zone 쐌 “Eastern” zone 쐌 “Atlantic” zone

쐌 Underneath the bumper and the cor- ner areas of the bumper cannot be viewed on the rear view monitor be- cause of its monitoring range limita- tion.

쐌 Do not put anything on the rear view camera. The rear view camera is in- stalled above the license plate.

쐌 When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, wa- ter may enter the camera unit caus- ing water condensation on the lens, a malfunction, fire or an electric shock. 쐌 Do not strike the camera. It is a pre- cision instrument. Otherwise, it may malfunction or cause damage result- ing in a fire or an electric shock.

CAUTION

There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from it.

SAA0889

HOW TO READ THE DISPLAYED LINES Lines which indicate the vehicle clearance and distances to objects with reference to the bumper line 쎻A are displayed on the monitor. They are indicated as reference distances to objects. Displayed lines indicate distances 1.5
feet (red) 쎻1 , 3 feet (yellow) 쎻2 , 7 feet (green) 쎻3 and 10 feet (green) 쎻4 from the lower part of the bumper line 쎻A . The vehicle clearance lines are wider than the actual clearance.

REAR VIEW MONITOR SETTING

WARNING

Do not adjust the Brightness, Contrast, Tint and Color of the rear view monitor while the vehicle is moving. Make sure the parking brake is firmly applied and the engine is not running.

To adjust the Brightness, Contrast, Tint and Color of the rear view monitor, push the “SET- TING” button with the rear view monitor on, select the item key and adjust the level using the joystick. OPERATING TIPS 쐌 When the selector lever is shifted to R, the monitor screen automatically changes to the rear view monitor mode. However, the radio can be heard.

쐌 It may take some time until the rear view monitor is displayed after the selector lever has been shifted to R. Objects may be dis- torted momentarily until the rear view monitor screen is displayed completely. When the selector lever is returned to a position other than R, it may take some time until the screen

4-20 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

changes. Objects on the screen may be distorted until they are completely displayed. 쐌 When the temperature is extremely high or low, the screen may not clearly display ob- jects. This is not a malfunction.

쐌 When strong light directly enters the camera,

objects may not be displayed clearly.

쐌 Vertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction.

쐌 The screen may flicker under light. This is not a malfunction.

fluorescent

쐌 The colors of objects on the rear view monitor may differ somewhat from those of the actual object.

쐌 When the contrast of objects is low at night, pushing the “ENTER” button may not change the brightness.

쐌 Objects on the monitor may not be clear in a

dark place or at night.

쐌 If dirt, rain or snow attaches to the camera, the rear view monitor may not clearly display objects. Clean the camera.

쐌 Do not use alcohol, benzine or thinner to clean the camera. This will cause discolora- tion. To clean the camera, wipe with a cloth

VENTILATORS

dampened with diluted mild cleaning agent and then wipe with a dry cloth.

쐌 Do not damage the camera as the monitor

screen may be adversely affected.

쐌 Do not use body wax on the camera window. Wipe off any wax with a clean cloth damp- ened with mild detergent diluted with water.

Center ventilators

SAA1064

Display screen, heater, air conditioner and audio systems 4-21

Side ventilators

SAA1065A

墌 05.8.26/Z50-D/V5.0 墍

Rear ventilator (if so equipped)

Open or close, and/or adjust the air flow direc- tion of ventilators.

SAA1066

: This symbol indicates that the vents are closed when the vent switch is moved to the left.

: This symbol indicates that the vents are open when the vent switch is moved to the right.

4-22 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

HEATER AND AIR CONDITIONER (Automatic)

8. Temperature control knob (driver only, or

driver and passenger)

9. “OFF” button for climate control system 10. Fan speed control knob 11. “DUAL” passenger side temperature con-

trol ON/OFF button

12. Temperature control knob (passenger side)

1. “AUTO” climate control ON button 2. “

” fresh air button

3. “

4. “

” air recirculation button

” front defroster button

SAA0641

5. “

” rear window defroster switch; refer to the “2. Instrument and controls” section.

6. “A/C” air conditioner ON/OFF button 7. “MODE” manual air flow control button

Display screen, heater, air conditioner and audio systems 4-23

墌 05.8.26/Z50-D/V5.0 墍

WARNING

쐌 The air conditioner cooling function operates only when the engine is running.

쐌 On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals. Do not leave children or adults who would normally require the assistance of others in your ve- hicle. Unattended pets should also not be left alone.

쐌 Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

쐌 Positioning of the heater and/or air conditioner controls should not be done while driving so that full atten- tion may be given to vehicle operation.

Start the engine and operate the controls to

activate the air conditioner. AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Push the AUTO button on. (AUTO will be

displayed.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 Adjust the temperature set dial to about 75°F

(24°C) for normal operation.

쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.

3. You can individually set driver and front pas- senger side temperature using each tem- perature control knob. When the DUAL but- ton is pushed or passenger side temperature control knob is turned, the DUAL indicator will come on. To turn off the passenger side temperature control, push the DUAL button.

Heating (A/C OFF) The air conditioner does not activate. When you need to heat only, use this mode.

1. Push the A/C button.

(A/C OFF will be

displayed and A/C indicator will turn off.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.

쐌 Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.

쐌 Not recommended if windows fog up. Dehumidified defrosting or defogging FRONT defroster button on. 1. Push the (The indicator light on the button will come on.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 To quickly remove ice from the outside of the windows, turn the fan speed control knob to right and set to the maximum position.

쐌 As soon as possible after the windshield is

4-24 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

clean, push the AUTO button to return to the auto mode. 쐌 When the

front defroster button is pushed, the air conditioner will automatically be turned on at outside temperatures above 23°F (−5°C) to defog the windshield, and the air recirculate mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.

to manually

MANUAL OPERATION Fan speed control Turn the fan control button control the fan speed. Push the AUTO button to return to automatic control of the fan speed. Air recirculation Push the air recirculation button to recir- culate interior air inside the vehicle. The indicator light on the cannot be activated The air recirculation when the air conditioner is in the front defrosting mode

button will come on.

To turn the system off Push the OFF button. OPERATING TIPS When the engine coolant temperature and out- side air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, the air flow from the foot outlets will operate normally.

Fresh air Push the button to draw outside air into the passenger compartment. The indicator light on the button will come on. Automatic intake air control In the AUTO mode, the intake air will be con- the trolled automatically. To manually control intake air, push the air recirculate or fresh air button. To return to the automatic control mode, push the indicator-illuminated but- ton for about 2 seconds. The indicator lights (both air recirculate and fresh air buttons) will flash twice, and then the intake air will be controlled automatically. Air flow control Pushing the MODE manual air button selects the air outlet to:

flow control

: Air flows from center and side ventila-

tors.

: Air flows from center and side ventila-

tors and foot outlets.

: Air flows from foot outlets and side

ventilators.

: Air flows from defroster,

and side ventilators.

foot outlets

Display screen, heater, air conditioner and audio systems 4-25

墌 05.8.26/Z50-D/V5.0 墍

decreases significantly or if windows fog up easily when operating the heater or air conditioning system.

SAA0642

The sensor on the instrument panel helps main- tain a constant temperature; do not put anything on or around this sensor. IN-CABIN MICROFILTER The air conditioning system is equipped with an in-cabin microfilter which collects dirt, pollen, dust, etc. To make sure the air conditioner heats, defogs, and ventilates efficiently, replace the filter according to the specified maintenance intervals listed in your Service and Maintenance Guide. To replace the filter, contact a NISSAN dealer. The filter should be replaced if the air flow 4-26 Display screen, heater, air conditioner and audio systems

SERVICING AIR CONDITIONER

The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricants are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubri- cants will cause severe damage to your air conditioning system. See “Capacities and rec- ommended fuel/lubricants” in the “9. Technical and consumer information” section for air con- ditioning system refrigerant and lubricant recom- mendations.

A NISSAN dealer will be able to service your environmentally friendly air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equip- ment.

墌 05.8.26/Z50-D/V5.0 墍

AUDIO SYSTEM

Turn the ignition switch to ACC or ON and push the power on switch to turn on the radio. If you listen to the radio with the engine not running, the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external in- fluences. Intermittent changes in reception qual- ity normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your radio system is equipped with state-of-the- art electronic circuits to enhance radio recep- tion. These circuits are designed to extend re- ception range, and to enhance the quality of that reception. However there are some general characteristics of FM, AM and satellite radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These characteristics are completely normal in a given reception area, and do not indicate any malfunc- tion in your radio system. Remember that a moving vehicle is not the ideal place to listen to a radio. Because of the move- ment, reception conditions will constantly

change. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception.

SAA0306

FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.

Fade and drift: As your vehicle moves away from

Display screen, heater, air conditioner and audio systems 4-27

墌 05.8.26/Z50-D/V5.0 墍

a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position, usually in conjunction with increased distance from the station transmitter, static or flutter can be heard. This can be reduced by adjusting the treble control counterclockwise to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and re- flected signals reach the receiver at the same time. The signals may cancel each other, result- ing in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical 4-28 Display screen, heater, air conditioner and audio systems

power lines, electric signs and even traffic lights. SATELLITE RADIO RECEPTION When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON for satellite radio to receive all of the neces- sary data. The satellite radio mode will be skipped or “NO SAT” will be displayed unless the optional sat- ellite receiver and antenna are installed, and an XM or SIRIUSTM satellite radio service sub- scription is active.

Satellite radio performance may be effected if cargo carried on the roof rack blocks the satellite radio signal. If possible, do not put cargo over the satellite radio antenna. AUDIO OPERATION PRECAUTIONS Cassette player 쐌 To maintain good quality

sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length. 쐌 Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and

away from direct sunlight, heat, dust, moisture and magnetic sources.

쐌 Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

쐌 Do not use cassettes with labels which are peeling and loose. If used, the label could jam in the player.

쐌 If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.

쐌 Over a period of time, the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape is played. This residue accumulation can cause weak or wavering sound, and should be removed periodically with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.

墌 05.8.26/Z50-D/V5.0 墍

쐌 During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player com- pletely.

쐌 The player may skip while driving on

rough roads.

쐌 The CD player sometimes cannot func- tion when the compartment tempera- ture is extremely high. Decrease the temperature before use.

쐌 Do not expose the CD to direct sunlight. 쐌 CDs that are of poor quality, dirty, scratched, covered with fingerprints, or that have pin holes may not work prop- erly.

쐌 The following CDs may not work prop-

erly: • Copy control compact discs (CCCD) • Recordable compact discs (CD-R) • Rewritable compact discs (CD-RW)

쐌 Do not use the following CDs as they may cause the CD player to malfunction. • 3.1 in (8 cm) discs with an adapter • CDs that are not round

• CDs with a paper label • CDs that are warped, scratched, or

have abnormal edges

쐌 CDs with MP3 or WMA format cannot be

written by this audio system.

쐌 If the CD cannot be played, one of the following messages will be displayed. CHECK DISC: • Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).

• Confirm that the CD is not bent or

warped and it is free of scratches.

PUSH EJECT: This is an error due to the temperature inside the player is too high. Remove the CD by pushing the EJECT button, and after a short time reinsert the CD. The CD can be played when the tem- perature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio sys- tem (only MP3 or WMA CD).

Display screen, heater, air conditioner and audio systems 4-29

墌 05.8.26/Z50-D/V5.0 墍

SAA0480

Compact Disc (CD) player 쐌 Only use high quality 4.7 inches (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging.

쐌 Sampling frequency — The rate at which the samples of a signal are converted from ana- log to digital (A/D conversion) per second. 쐌 Multisession — Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.

쐌 ID3/WMA Tag — The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag information is displayed on the Artist/Track title line on the display.

* Windows and Windows Media are regis- tered trademarks and trademarks in the United States of America and other countries of Microsoft Corporation of the USA.

Compact Disc (CD) with MP3 or WMA Explanation of terms: 쐌 MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD can reduce the file size by approximately 10:1 ratio (Sampling: 44.1
kHz, Bit rate: 128 kbps) with virtually no perceptible loss in quality. MP3 compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn’t hear.

쐌 WMA — Windows Media Audio (WMA) is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.

쐌 Bit rate — Bit rate denotes the number of bits per second used by a digital music files. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.

4-30 Display screen, heater, air conditioner and audio systems

SAA1025

Playback order:

Music playback order of the CD with MP3 or WMA is as illustrated above. 쐌 The folder names of folders not containing MP3/WMA files are not shown in the display.

墌 05.8.26/Z50-D/V5.0 墍

쐌 If there is a file in the top level of the disc,

“Root Folder” is displayed.

쐌 The playback order is the order in which the files were written by the writing software, so the files might not play in the desired order.

Specification chart:

Supported media

Supported file systems

CD, CD-R, CD-RW

ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not sup- ported.

Version

MPEG1, MPEG2, MPEG2.5

MP3

Sampling frequency

8 kHz - 48 kHz

Supported ver- sions*1

Bit rate

Version

8 kbps - 320 kbps, VBR

WMA7, WMA8, WMA9

WMA

Sampling frequency

32 kHz - 48 kHz

Bit rate

48 kbps - 192 kbps, VBR

Tag information (Song title and Artist name)

Folder levels

ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3
only)

Folder levels: 8, Folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder)

Text character number limitation

128 characters

Displayable character codes*2

01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16
Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be

played.

*2 Available codes depend on what kind of media, versions and information are going to be displayed. Display screen, heater, air conditioner and audio systems 4-31

墌 05.8.26/Z50-D/V5.0 墍

Troubleshooting guide:

Symptom

Cannot play

Poor sound quality It takes a relatively long time be- fore the music starts playing.

Music cuts off or skips

Skipping with high bit rate files Move immediately to the next song when playing. The songs do not play back in the desired order.

Cause and Countermeasure

Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player, and if there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played. Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and num- ber of characters for folder names and file names should be in compliance with the specifications. Check if the disc or the file is generated in an irregular format. This may occur depending on the variation or the setting of MP3/WMA writing applications or other text editing applications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. If there are many folder or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing. The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data. When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, “.mp3” or “.wma”, or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software, so the files might not play in the desired order.

4-32 Display screen, heater, air conditioner and audio systems

墌 05.8.26/Z50-D/V5.0 墍

FM-AM-SAT RADIO WITH CD PLAYER No satellite radio reception is available when the SAT band option is selected unless optional satellite receiver and antenna are installed, and an XM® or SIRIUSTM satellite radio service subscription is active.

It may take some time to receive the activation signal after subscribing to the XM or SIRIUSTM satellite radio provider. After receiving the acti- vation signal, an available channel list will be automatically updated in the radio. For XM , turn the ignition switch from the LOCK to ACC position to update the channel list.

Satellite radio is not available in Alaska and Hawaii. Audio main operation POWER/Volume control:

SAA1360

11. RADIO button 12. PAUSE/MUTE button 13. TUNE up/down, TRACK up/down and AU-

DIO button

14. RPT (repeat)/RDM (random) button

Turn the ignition switch to ACC or ON, and then push the POWER button while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. When no CD is loaded, the radio will come on. While the system is on, pushing the POWER button turns the system off. To turn the radio off, push the POWER button. Display screen, heater, air conditioner and audio systems 4-33

墌 05.8.26/Z50-D/V5.0 墍

1. SEEK/TRACK button

2. CD slot

3. Station and preset (FM/AM/SAT)

4. SCAN button

5. CD EJECT button

6. CAT button

7. POWER button/VOLUME control knob

8. DISP (display) button 9. PRESET A⋅B⋅C button 10. CD button

Turn the Volume control knob to adjust volume. AUDIO button/knob:

Push the AUDIO button to change the selecting mode as follows. BASS → TREBLE → FADE → BALANCE → BASS

the

turn the tuning knob within 2 seconds.

Display select:

Display CD text

To indicate the CD text, push the while the CD is playing. The text will change as follows:

button

To adjust Bass, Treble, Fader and Balance, push the AUDIO button until the desired mode BASS, TREBLE, FADE or BALANCE appears in the display. Turn the AUDIO knob to adjust Bass and Treble to the desired level. Use the Tuning knob also to adjust Fader or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. After 10 seconds, the radio or CD display reappears. Once the sound quality is set to the desired level, push the AUDIO button repeatedly until the radio or CD display appears. Display text: To indicate the text, push the AUDIO knob during CD or satellite radio playing. BASS → TREBLE → FADE → BALANCE → Display mode To change the indicated text in display mode, 4-34 Display screen, heater, air conditioner and audio systems

Display FM text To indicate the FM PS name, push the

button while the FM radio is playing.

The name will change as follows: ON → OFF → ON When no data is available, “NO TEXT” will appear. Display satellite radio text To indicate the satellite radio text, push the button while the satellite radio is playing.

The text will change as follows:

When no data is available, “----” will appear. FM-AM-SAT radio operation

FM/AM/SAT radio select:

The satellite radio mode will be skipped unless the optional satellite receiver and antenna are installed, and an XM or SIRIUSTM satellite radio service subscription is active.

Pushing the RADIO button will change the band as follows: AM → FM → SAT (Satellite) When the RADIO button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station played will also come on when the power knob is turned to ON. If a compact disc is playing when the RADIO button is pushed, the compact disc will auto- matically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal the radio will automatically change from stereo to monaural reception.

is weak,

墌 05.8.26/Z50-D/V5.0 墍

TUNE (Tuning):

WARNING

The radio should not be tuned while driving so full attention may be given to vehicle operation.

To tune the radio, turn the TUNE knob to the right or left. Use these buttons for manual tuning.

SEEK tuning: or

for less Push the SEEK button than 0.5 second to tune from high to low or low to high frequencies and stop at the next broad- casting station (channel). Push the SEEK button for more than 0.5 second, to fast tune from high to low or low to high frequencies. SCAN tuning:

or

Push the SCAN tuning button to tune from low to high frequencies and stop at each broadcast- ing station (channel) for 5 seconds. Pushing the button again during this 5 seconds period will stop SCAN tuning and the radio will remain tuned to that station (channel).

If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next station (channel). Station memory operations:

Eighteen (18) stations can be set for the FM, AM and SAT band to the A, B and C preset button.

1. Choose preset channel A, B or C using the

preset select button.

2. Tune to the desired station using the SEEK, SCAN or TUNE button and keep pushing any of the desired station memory buttons (1 to 6) until a beep sound is heard. (The radio mutes when the select button is pushed.)

3. The channel indicator will then come on and the sound will resume. Memorizing is now complete.

4. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse blows, the radio memory will be erased. In that case, reset the desired stations. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) and/or SATELLITE band encoded within a regu- lar radio broadcast. Currently, most RDS sta-

tions are in large cities, but many stations are now considering broadcasting RDS data.

RDS can display: 쐌 Station call sign, such as “WHFR 98.3”. 쐌 Station name, such as “The Groove”. 쐌 Music or programming type such as “Classi-

cal”, “Country”, or “Rock”.

쐌 Traffic reports about delays or construction. If the station broadcasts RDS information, the RDS icon is displayed.

Category (CAT) button:

When the CAT button is pushed for less than 0.5 second, the AM/FM (Satellite) radio frequen- cies (Category) will move to the next/previous step (Category). Push and hold the button for more than 0.5 second to move quickly through the steps (Categories). Compact disc (CD) player operation Turn the ignition switch to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. After loading the disc, the number of tracks on

Display screen, heater, air conditioner and audio systems 4-35

墌 05.8.26/Z50-D/V5.0 墍

the disc and the play time will appear on the display. If the radio is already operating, it will automati- cally turn off and the compact disc will play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

If the system has been turned off while the compact disc was playing, pushing the POWER/VOL control knob will start the com- pact disc. 3.1 inches (8 cm) diameter discs can be used without an adapter.

PLAY:

When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When the CD button is pushed with the com- pact disc loaded with the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play.

FF (Fast Forward), REW (Rewind), APS (Automatic Program Search) FF, APS REW:

(fast forward) or

(rewind) When the button is pushed and hold while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is released, the compact disc will return to normal play speed.

button is pushed for less than When the 0.5 second while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will advance the number of times the button is pushed. (When the last program on the compact disc is skipped through, the first pro- button is gram will be played.) When the pushed for less than 0.5 second, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.

SCAN:

When the SCAN button is pushed while the CD is playing, each track will play for about 10
seconds.

4-36 Display screen, heater, air conditioner and audio systems

To stop scanning, push the SCAN button again.

RPT (Repeat)/RDM (Random):

When the RPT/RDM button is pushed while the compact disc is played, the play pattern can be changed as follows:

CD EJECT:

When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected. When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it.

墌 05.8.26/Z50-D/V5.0 墍

FM-AM-SAT RADIO WITH CASSETTE PLAYER AND CD CHANGER No satellite radio reception is available when the SAT band option is selected unless optional satellite receiver and antenna are installed, and an XM® or SIRIUSTM satellite radio service subscription is active. It may take some time to receive the activation signal after subscribing to the XM or SIRIUSTM satellite radio provider. After receiving the acti- vation signal, an available channel list will be automatically updated in the radio. For XM , turn the ignition switch from the LOCK to ACC position to update the channel list. Satellite radio is not available in Alaska and Hawaii. Audio main operation The tape deck employs a permalloy head which allows for improved reproduction of high fre- quency ranges. Noise is also greatly reduced by the combined use of the Dolby NR (Noise Reduction) system. The auto loudness circuit enhances the low frequency range automatically in both radio reception and tape and CD play- back.

SAA1315

11. CD button 12. RADIO button 13. TAPE EJECT button 14. TAPE button 15. TUNE up/down, TRACK up/down and AU-

DIO button

16. RPT (repeat)/RDM (random) button

Display screen, heater, air conditioner and audio systems 4-37

墌 05.8.26/Z50-D/V5.0 墍

1. CD LOAD button

2. SEEK/TRACK button 3. CD slot 4. Station

and

preset

(FM/AM/SAT)/CD

insert/eject or CD play select button

5. SCAN button

6. CD EJECT button

7. CAT/FOLDER button

8. POWER button/VOLUME control knob

9. DISP (display) button 10. PRESET A⋅B⋅C button

mark.

POWER/Volume control:

Turn the ignition switch to ACC or ON, and then push the POWER button while the system is off to call up the mode (radio, tape or CD) which was playing immediately before the system was turned off. When no CD or tape is loaded, the radio will come on. While the system is on, pushing the POWER button turns the system off. To turn the radio off, push the POWER button. Turn the Volume control knob to adjust the volume. This vehicle has Speed Sensitive control Vol- ume (SSV) for audio. The audio volume changes as the driving speed changes. AUDIO button/knob: Push the AUDIO button to change the selecting mode as follows. BASS → TREBLE → FADE → BALANCE → SSV → NR (when cassette playing) To adjust Bass, Treble, Fader and Balance, push the AUDIO button until the desired mode BASS, TREBLE, FADE or BALANCE appears in the display. Turn the AUDIO knob to adjust Bass and Treble to the desired level. Use the Tuning