Download PDF Manual

Push the tuning switch ( ) for more than 1.5 seconds to seek the next or previ- ous radio station. FF, REW (tape and CD): Push the tuning switch ( ) for less 1.5 seconds to return to the beginning of the present program or skip to the next program. Push several times to skip back or skip through programs. The automatic program search searches for the blank intervals between selections on cassette tapes. If there is a blank interval within a program


or


or there is no interval between programs, the system may not stop in the desired or expected location.


When playing a tape, push the tuning switch ) for more than 1.5 seconds to rewind or fast forward the tape.


or


To stop the FF or REW function, press the or


button for less than 1.5 seconds again.


) for more than 1.5 seconds to change


When playing a CD in the CD changer (if so equipped), push the tuning switch ( or between discs when multiple CDs are loaded. ANTENNA Window antenna The antenna pattern is printed inside the rear window.


CAUTION


c Do not place metalized film near the rear window glass or attach any metal parts to it. This may cause poor recep- tion or noise.


LHA0269


POWER on/off switch Tuning switch


Volume control switch 1. 2. MODE select switch 3. 4. STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off.


4-32 Display screen, heater, air conditioner and audio systems


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


CAR PHONE OR CB RADIO


c When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna. Lightly wipe along the antenna with a dampened soft cloth.


When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may ad- versely affect the engine control system and other electronic parts.


WARNING


c A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some juris- dictions prohibit the use of cellular tele- phones while driving.


c If you must make a call while your ve- hicle is in motion, the hands free cellu- lar phone operational mode (if so equipped) is highly recommended. Ex- ercise extreme caution at all times so full attention may be given to vehicle operation.


c If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.


CAUTION


c Keep the antenna as far away as pos- control


sible from the electronic modules.


c Keep the antenna wire more than 8 in (20 cm) away from the electronic con- trol system harnesses. Do not route the antenna wire next to any harness.


c Adjust the antenna standing-wave ratio as recommended by the manufacturer. c Connect the ground wire from the CB


radio chassis to the body.


c For details, consult a NISSAN dealer.


Display screen, heater, air conditioner and audio systems 4-33


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


MEMO


4-34 Display screen, heater, air conditioner and audio systems


5 Starting and driving


Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2
Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2
Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Avoiding collision and rollover. . . . . . . . . . . . . . . . . . . . 5-3
Drinking alcohol/drugs and driving. . . . . . . . . . . . . . . . 5-3
Ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Automatic transmission. . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Manual transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Key positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Nissan vehicle immobilizer system (NVIS) . . . . . . . . . 5-5
Before starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Driving the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Automatic transmission (if so equipped). . . . . . . . . . . 5-7
Manual transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Cruise control (if so equipped) . . . . . . . . . . . . . . . . . . . . . 5-13
Precautions on cruise control . . . . . . . . . . . . . . . . . . . 5-13
Cruise control operations. . . . . . . . . . . . . . . . . . . . . . . 5-14


Break-in schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Increasing fuel economy. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Parking/parking on hills. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Power steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Brake precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Anti-lock brake system (ABS) . . . . . . . . . . . . . . . . . . . 5-18
Traction control system (TCS) (if so equipped) . . . . . . . 5-19
Vehicle dynamic control (VDC) system (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
Cold weather driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Freeing a frozen door lock . . . . . . . . . . . . . . . . . . . . . . 5-21
Anti-freeze. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Draining of coolant water . . . . . . . . . . . . . . . . . . . . . . . 5-21
Tire equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
Special winter equipment. . . . . . . . . . . . . . . . . . . . . . . 5-22
Driving on snow or ice . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
Engine block heater (if so equipped) . . . . . . . . . . . . . 5-23


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.


c Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in- jured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children(cid:146)s access to car keys.


EXHAUST GAS (carbon monoxide)


WARNING


c Do not breathe exhaust gases; they con- tain colorless and odorless carbon mon- oxide. Carbon monoxide is dangerous. It can cause unconsciousness or death.


5-2 Starting and driving


c If you suspect that exhaust fumes are entering the vehicle, drive with all win- dows fully open, and have the vehicle inspected immediately.


c Do not run the engine in closed spaces


such as a garage.


c Do not park the vehicle with the engine running for any extended length of time. c Keep the trunk lid closed while driving, otherwise exhaust gases could be drawn into the passenger compart- ment. If you must drive with the trunk lid open, follow these precautions: 1. Open all the windows. 2. Set the


air recirculation but- ton to off and the fan control dial to high to circulate the air.


c If electrical wiring or other cable con- nections must pass to a trailer through the seal on the trunk lid or the body, follow the manufacturer(cid:146)s recommen- dation to prevent carbon monoxide en- try into the vehicle.


c The exhaust system and body should be inspected by a qualified mechanic whenever:


a. The vehicle is raised for service. b. You suspect that exhaust fumes are passenger


into


the


entering compartment.


c. You notice a change in the sound of


the exhaust system.


d. You have had an accident involving damage to the exhaust system, un- derbody, or rear of the vehicle.


THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.


WARNING


c The exhaust gas and the exhaust sys- tem are very hot. Keep people, animals or flammable materials away from the exhaust system components.


c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


CAUTION


c Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst(cid:146)s ability to help reduce exhaust pollutants.


c Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driv- ing if the engine misfires, or if notice- able loss of performance or other un- usual are detected. Have the vehicle inspected promptly by a NISSAN dealer.


conditions


operating


c Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the three-way catalyst.


c Do not race the engine while warming it


up.


c Do not push or tow your vehicle to start


the engine.


AVOIDING COLLISION AND ROLLOVER


DRINKING ALCOHOL/DRUGS AND DRIVING


WARNING


WARNING


Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.


Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any ve- hicle, loss of control could result in a colli- sion with other vehicles or objects, or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide side- ways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over- the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the (cid:147)Safety (cid:150) Seats, seat belts and supplemental re- straint system(cid:148) section of this manual, and also instruct your passengers to do so. Seat belts help reduce the risk of injury in collisions and rollovers. In a rollover crash, an unbelted or improperly belted person is significantly more likely to be injured or killed than a person properly wearing a seat belt.


Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.


NISSAN is committed to safe driving. However, you must choose not to drive under the influence of alcohol. Every year thousands of people are injured or killed in alcohol-related accidents. Al- though the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don(cid:146)t mix! And that is true for drugs, too (over-the-counter, pre- scription, and illegal drugs). Don(cid:146)t drive if your ability to operate your vehicle is impaired by alco- hol, drugs, or some other physical condition.


Starting and driving 5-3


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


IGNITION SWITCH


WSD0041


AUTOMATIC TRANSMISSION The ignition lock is designed so the key cannot be turned to the LOCK position and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the selector lever is not returned to P (Park) position, the key cannot be moved to the LOCK position.


5-4 Starting and driving


When the ignition is in the OFF position, the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left. If the key will not turn from the LOCK posi- tion, turn the steering wheel to the left or right while turning the key to unlock the key cylinder.


WARNING


Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


To remove the key from the ignition switch:


1. Shift the selector lever to the P (Park) posi-


tion with the key in the ON position.


2. Turn the key to the LOCK position.


3. Remove the key from the ignition.


If the selector lever is shifted to the P (Park) posi- tion after the key is turned to the OFF position or when the key cannot be turned to the LOCK posi- tion, proceed as follows to remove the key.


1. Move the shift selector lever into the P (Park)


position.


2. Turn the ignition key slightly toward the ON


position.


3. Turn the key to the LOCK position. 4. Remove the key. The shift selector lever is designed so it cannot moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF position or if the key is removed from the switch. The shift selector lever can be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ACC positions. The OFF position is indicated by a (cid:147)1(cid:148) on the key cylinder.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


WSD0058


MANUAL TRANSMISSION The ignition switch includes a device that helps prevent accidental removal of the key while driv- ing.


The key can only be removed when the ignition switch is in the LOCK position.


On manual transmission models, to turn the igni- tion key to LOCK position from ACC or ON position, turn the key to OFF, push the key in, then turn the key to LOCK.


In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position.


To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steer- ing wheel slightly right and left.


WARNING


Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury. KEY POSITIONS LOCK: Normal parking position (0) OFF: (Manual transmission model) (1) The engine can be turned off without locking the steering wheel. ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON: Normal operating position (3) This position turns on the ignition system and the electrical accessories.


START: (4) This position starts the engine. As soon as the engine has started, release the key. It automati- cally returns to the ON position. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The NISSAN Vehicle Immobilizer System (NVIS) will not allow the engine to start without the use of the registered NVIS key. If the engine fails to start using the registered NVIS key, it may be due to interference caused by an- other NVIS key, an automated toll road device or automated payment device on the key ring. Restart the engine using the following procedures: 1. Leave the ignition switch in the ON position


for approximately 5 seconds.


2. Turn the ignition switch to the OFF or LOCK position and wait approximately 10 seconds.


3. Repeat step 1 and 2 again. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered NVIS key.


If this procedure allows the engine to start, NISSAN recommends placing the registered NVIS key on a separate key ring to avoid interfer- ence from other devices.


Starting and driving 5-5


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


BEFORE STARTING THE ENGINE


STARTING THE ENGINE


c Make sure the area around the vehicle is


clear.


c Check fluid levels such as engine oil, cool- ant, brake and clutch fluid, and window washer fluid as frequently as possible, or at least whenever you refuel.


c Check that all windows and lights are clean. c Visually inspect tires for their appearance and condition. Also check tires for proper inflation.


c Lock all doors. c Position seat and adjust head restraints. c Adjust inside and outside mirrors. c Fasten seat belts and ask all passengers to


do likewise.


c Check the operation of warning lights when the key is turned to the ON (3) position. See (cid:147)Warning/indicator lights and audible re- minders(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual.


5-6 Starting and driving


1. Apply the parking brake. 2. Automatic transmission:


Move the shift selector lever to P (Park) or N (Neutral). P (Park) is recommended. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the OFF position or if the key is removed from the ignition switch.


The starter is designed not to operate if the shift selector lever is in any of the driving positions.


Manual transmission:


Move the shift lever to N (Neutral). Depress the clutch pedal to the floor while cranking the engine. The starter is designed not to operate unless the clutch pedal is fully de- pressed.


3. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.


c If the engine is very hard to start in ex- tremely cold weather or when restarting, depress the accelerator pedal a little (ap- proximately 1/3 to the floor) and hold it and then crank the engine. Release the key and the accelerator pedal when the engine starts.


c If the engine is very hard to start because it is flooded, depress the accelerator pedal all the way to the floor and hold it. Crank the engine for 5-6 seconds. After cranking the engine, release the accel- erator pedal. Crank the engine with your foot off the accelerator pedal by turn- ing the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure.


CAUTION


Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10
seconds before cranking again, otherwise the starter could be damaged.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


4. Allow the engine to idle for at least 30 sec- onds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the engine running for a minimum of 2(cid:150)3 minutes before shutting it off. Starting and stopping the engine over a short period of time may make the vehicle more difficult to start.


DRIVING THE VEHICLE


AUTOMATIC TRANSMISSION (if so equipped)


WARNING


c Do not depress the accelerator pedal while shifting from P (Park) or N (Neu- tral) to R (Reverse), D (Drive), 2 or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident.


c Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.


c Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.


CAUTION


c When stopping the vehicle on an uphill grade, do not hold the vehicle by de- pressing the accelerator pedal. The foot brake should be used for this purpose. c Do not downshift abruptly on slippery roads. This may cause a loss of control.


The automatic transmission in your vehicle is electronically controlled to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle 1. After starting the engine, fully depress the foot brake pedal before attempting to move the shift selector lever out of the P (Park) position.


2. Keep the foot brake pedal depressed and move the shift selector lever into a driving gear.


3. Release the foot brake, then gradually start


the vehicle in motion.


The automatic transmission is designed so the foot brake pedal MUST be depressed before shifting from P (Park) to any drive position while the ignition switch is in the ON position. The shift selector lever cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to the LOCK, OFF or ACC position or if the key is removed.


Starting and driving 5-7


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


LSD0071


Shifting After starting the engine, fully depress the brake pedal and move the shift selector lever out of the P (Park) position.


WARNING


Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage.


If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or 5-8 Starting and driving


R (Reverse):


CAUTION


Use this position only when the vehicle is completely stopped.


Use this position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the selector lever from P (Park), N (Neutral) or any drive position to R (Reverse). N (Neutral): Neither forward nor reverse gear is engaged. The engine can be started in this position. You may shift to N (Neutral) and restart a stalled engine while the vehicle is moving. D (Drive): Use this position for all normal forward driving.


any D (Drive) position, the shift selector lever cannot be moved to P (Park). Additionally, the key cannot be turned to the LOCK position and be removed from the ignition switch. If this occurs, perform the following steps:


1. Apply the parking brake when the vehicle is


stopped.


2. Turn the key to the ON position.


3. Depress the foot brake pedal.


4. Move the shift selector lever to P (Park) or N (Neutral) to restart the vehicle (P is pre- ferred). Move the shift selector lever to P (Park) to park the vehicle and turn the igni- tion key to the LOCK position to remove the key.


P (Park):


Use this selector position when the vehicle is parked or when starting the engine. Make sure the vehicle is completely stopped. The brake pedal must be depressed to move the se- lector lever from N (Neutral) or any drive position to P (Park). Apply the parking brake. When parking on a hill, apply the parking brake first, then move the shift selector lever into the P (Park) position.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


LSD0071


Manual shift mode When the selector lever is shifted from D to the manual shift gate with the vehicle stopped or while driving, the transmission enters the manual shift mode. Shift ranges can be selected manu- ally.


In the manual shift mode, the shift range is dis- played on the position indicator in the meter. When shifting the shift lever to the manual shift gate, the position indicator first displays M4
(Fourth)


Shift ranges up or down one by one as follows: M1ˆ! M2 ˆ! M3 ˆ! M4 ˆ! M5


M5 (Fifth):


Use this position for all normal forward driving. M4 (Fourth):


For driving up or down long slopes where engine braking would be advantageous. M3 (Third) and M2 (Second):


Use for hill climbing or engine braking on downhill grades. M1 (First):


Use this position when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. c Remember not to drive at high speeds for extended periods of time in lower than M4
range. This reduces fuel economy.


When shifting up: Move the selector lever to the + (up) side. (Shifts to higher range.) When shifting down: Move the selector lever to the 2 (down) side. (Shifts to lower range.) c The transmission will automatically down- shift the gears. (For example, if you select the


3rd range, the transmission will shift down between the 3rd and 1st gears.)


c Moving the selector lever rapidly to the same side twice will shift the ranges in succession.


When canceling the manual shift mode: Return the selector lever to the D position to return the transmission to the normal driving mode. c In the manual shift mode, the transmis- sion may not shift to the selected gear. This helps maintain driving perfor- mance and reduces the chance of ve- hicle damage or loss of control.


c In the manual shift mode, the transmis- sion may shift up automatically to a higher range than selected if the en- gine speed is too high. When the ve- hicle speed decreases, the transmis- sion automatically shifts down and shifts to 1st gear before the vehicle comes to a stop.


Starting and driving 5-9


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


LSD0072


Shift lock release If the battery is discharged, the shift selector lever may not be moved from the P (Park) position even with the brake pedal depressed.


To move the shift selector lever, release the shift lock. The shift selector lever can be moved to N (Neutral). However, the steering wheel will be locked unless the ignition switch is turned to the ON position. This allows the vehicle to be moved if the battery is discharged.


To push the shift lock release, complete the fol- lowing procedure:


5-10 Starting and driving


1. Turn the ignition key to the LOCK position


and remove the key


2. Apply the parking brake.


3. Remove the shift


lock release cover as


shown.


4.


Insert a small screwdriver in the shift lock release slot and push down.


5. Move the shift selector lever to the N (Neu- tral) position while holding down the shift lock release.


6. Turn the key to the ON position to unlock the steering wheel. Now the vehicle may be moved to the desired location.


If the shift selector lever cannot be moved out of P (Park), have a NISSAN dealer check the auto- matic transmission system as soon as possible.


WARNING


If the selector lever cannot be moved from the P (Park) position while the engine is running and the brake pedal is depressed, the stop lights may not work. Malfunction- ing stop lights could cause an accident injuring yourself and others.


Accelerator downshift (cid:151) in D position (cid:151) For passing or hill climbing, depress the accel- erator pedal to the floor. This shifts the transmis- sion down into a lower gear, depending on the vehicle speed. Fail-safe When the fail-safe operation occurs, please note that the 4(cid:150)speed automatic transmission will be locked in third gear. For the 5(cid:150)speed automatic transmission, the transmission will be locked in any of the gears according to the condition. If the vehicle is driven under extreme con- ditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated. This will occur even if all electrical circuits are functioning properly. In this case, turn the ignition key OFF and wait for 3 seconds. Then turn the key back to the ON position. The vehicle should return to its normal operating con- dition. If it does not return to its normal operating condition, have a NISSAN dealer check the transmission and repair it if nec- essary.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


MANUAL TRANSMISSION


WARNING


c Do not downshift abruptly on slippery roads. This may cause a loss of control. c Do not over-rev the engine when shift- ing to a lower gear. This may cause a loss of control or engine damage.


CAUTION


c Do not rest your foot on the clutch pedal while driving. This may cause clutch damage.


c Fully depress the clutch pedal before shifting to help prevent transmission damage.


c Stop your vehicle completely before


shifting into R (Reverse).


c When the vehicle is stopped with the engine running (for example, at a stop light), shift to N (Neutral) and release the clutch pedal with the foot brake applied.


LSD0073


Shifting To change gears, or when upshifting or down- shifting, depress the clutch pedal fully, shift into the appropriate gear, then release the clutch slowly and smoothly.


This vehicle is equipped with a short throw shifter manual transmission. To ensure smooth gear changes, fully depress the clutch pedal before operating the shift lever. If the clutch pedal is not fully depressed before the transmission is shifted, a gear noise may be heard. Transmission damage may occur.


Start the vehicle in 1st gear and shift to 2nd, 3rd, 4th and 5th up to 6th gear in sequence according to vehicle speed.


To back up, lift up on the reverse lever and then move it to the R (Reverse) position after stopping the vehicle completely.


If it is difficult to move the shift lever into R (Reverse) or 1 (1st), shift into N (Neutral), then release the clutch pedal. Depress the clutch pedal again and shift into R (Reverse) or 1 (1st). Suggested upshift speeds The following are suggested vehicle speeds for shifting into a higher gear. These suggestions relate to fuel economy and vehicle performance. Actual upshift speeds will vary according to road conditions, the weather and individual driving habits. For quick acceleration in low altitude areas (less than 4,000 ft [1219 m]) and normal accelera- tion in high altitude areas (over 4,000 ft [1219 m]):


GEAR CHANGE


MPH (km/h)


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th


15 (24) 25 (40) 40 (64) 45 (72) 50 (80)


Starting and driving 5-11


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


PARKING BRAKE


WARNING


c Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident.


c Do not release the parking brake from


outside the vehicle.


c Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged.


c Do not leave children unattended in a vehicle. They could release the parking brake and cause an accident.


For quick acceleration in high altitude areas (over 4,000 ft [1219 m]): GEAR CHANGE


MPH (km/h)


1st to 2nd 2nd to 3rd 3rd to 4th 4th to 5th 5th to 6th


15 (24) 25 (40) 40 (64) 45 (72) 50 (80)


Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will en- sure safe operation. Do not over-rev the engine when shifting to a lower gear as it may cause engine damage or loss of vehicle control.


GEAR


1st 2nd 3rd 4th 5th 6th


MPH (km/h)


35 (56) 57 (92) 80 (128)


(cid:151) (cid:151) (cid:151)


5-12 Starting and driving


LSD0074


To engage: Pull the lever up sA . To release:


1. Firmly apply the foot brake. 2. Manual transmission models:


Place the shift lever in the N (Neutral) posi- tion. Automatic transmission models: Move the shift selector lever to the P (Park) position.


3. While pulling up on the parking brake lever slightly, push the button and lower com- pletely sB .


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


CRUISE CONTROL (if so equipped)


4. Before driving, be sure the brake warning


light goes out.


pushing


c The SET indicator light may blink when the cruise control main switch is turned ON while ACCEL/RES, COAST/SET, or CANCEL switch (located on the steering wheel). To properly set the cruise control system, use the following pro- cedures.


the


LSD0075


ACCEL/RES switch 1. 2. COAST/SET switch 3. ON/OFF switch 4. CANCEL switch PRECAUTIONS ON CRUISE CONTROL c If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the instrument panel then blinks to warn the driver.


c If the SET indicator light blinks, turn the cruise control main switch off and have the system checked by a NISSAN dealer.


WARNING


Do not use the cruise control when driving under the following conditions: c When it is not possible to keep the


vehicle at a set speed.


c In heavy traffic or in traffic that varies in


speed.


c On winding or hilly roads. c On slippery roads (rain, snow, ice, etc.). c In very windy areas. Doing so could cause a loss of vehicle control and result in an accident.


Starting and driving 5-13


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


CAUTION


On manual transmission models, do not shift into N (Neutral) without depressing the clutch pedal when the cruise control is set. Should this occur, depress the clutch pedal and turn the main switch off imme- diately. Failure to do so may cause engine damage. CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed be- tween 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the main switch. The CRUISE indicator light in the instru- ment panel comes on. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. c To pass another vehicle, depress the ac- celerator pedal. When you release the pedal, the vehicle returns to the previously set speed.


5-14 Starting and driving


c The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control.


To cancel the preset speed, use one of the following three methods. c Push the CANCEL button; the SET indicator


light in the instrument panel goes out.


c Tap the brake pedal; the SET indicator light


goes out.


c Turn the main switch off. Both the CRUISE indicator light and SET indicator light in the instrument panel go out.


The cruise control is automatically canceled and the SET light in the instrument panel goes out if: c you depress the brake or clutch pedal while pushing the ACCEL/RES or SET/COAST switch. The preset speed is deleted from memory.


c the vehicle slows down more than 8 MPH


(13 km/h) below the set speed.


c you depress the clutch pedal (manual trans- mission), or move the shift selector lever to N (Neutral) (automatic transmission).


To reset at a faster cruising speed, use one of the following three methods. c Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.


c Push and hold the ACCEL/RES switch. When the vehicle attains the speed you de- sire, release the switch.


c Push and release the ACCEL/RES switch. Each time you do this, the set speed in- creases by about 1 MPH (1.6 km/h).


To reset at a slower cruising speed, use one of the following three methods. c Lightly tap the brake pedal. When the ve- hicle attains the desired speed, push the COAST/SET switch and release it.


c Push and hold the COAST/SET switch. Re- lease the switch when the vehicle slows to the desired speed.


c Push and release the COAST/SET switch. Each time you do this, the set speed de- creases by about 1 MPH (1.6 km/h).


To resume the preset speed, push and re- lease the ACCEL/RES switch. The vehicle re- turns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


BREAK-IN SCHEDULE


INCREASING FUEL ECONOMY


CAUTION


During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and en- sure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in short- ened engine life and reduced engine performance. c Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm.


c Do not accelerate at full throttle in any gear. c Avoid quick starts. c Avoid hard braking as much as possible. c Do not tow a trailer for the first 500 miles (800 km). Your engine, axle or other parts could be damaged.


c Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position.


c When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag.


c Use the recommended viscosity engine oil. See (cid:147)Engine oil and oil filter recommenda- tion(cid:148) in (cid:147)Technical and consumer informa- tion(cid:148) later in this manual.


c Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. c Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles.


c Use a proper gear range which suits road conditions. On level roads, shift into high gear as soon as possible.


c Avoid unnecessary engine idling. c Keep your engine tuned up. c Follow the recommended periodic mainte-


nance schedule.


c Keep the tires inflated to the correct pres- sure. Low tire pressure increases tire wear and lowers fuel economy.


c Keep the wheels in correct alignment. Im- proper alignment increases tire wear and lowers fuel economy.


c Air


conditioner operation


fuel economy. Use the air conditioner only when necessary.


lowers


Starting and driving 5-15


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


PARKING/PARKING ON HILLS


2. Manual transmission models:


Place the shift lever in the R (Reverse) posi- tion. When parking on an uphill grade, place the shift lever in 1st gear. Automatic transmission models: Move the shift selector lever to the P (Park) position.


3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated. c HEADED DOWNHILL WITH CURB: sA


Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.


c HEADED UPHILL WITH CURB: sB


Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb.


c HEADED UPHILL OR DOWNHILL, NO


CURB: sC Turn the wheels toward the side of the road so the vehicle will move away from the cen- ter of the road if it moves.


4. Turn the ignition key to the LOCK position


and remove the key.


WARNING


c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


c Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for automatic transmission models or in an appropriate gear for manual transmis- sion models. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in an accident.


5-16 Starting and driving


WSD0050


Make sure the shift lever has been pushed as far forward as it can go and cannot be moved without depressing the foot brake pedal.


c Never leave the engine running while


the vehicle is unattended.


c Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls. Unattended children could become involved in seri- ous accidents.


1. Firmly apply the parking brake.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


POWER STEERING


BRAKE SYSTEM


The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.


WARNING


If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be much harder to operate.


The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. BRAKE PRECAUTIONS Vacuum assisted brakes The brake booster aids braking by using engine vacuum. If the engine stops, you can stop the vehicle by depressing the brake pedal. However, greater foot pressure on the brake pedal will be required to stop the vehicle and stopping dis- tance will be longer. Using the brakes Avoid resting your foot on the brake pedal while driving. This will overheat the brakes, wear out the brakes and pads faster, and reduce gas mileage.


To help reduce brake wear and to prevent the brakes from overheating, reduce speed and downshift to a lower gear before going down a slope or long grade. Overheated brakes may reduce braking performance and could result in loss of vehicle control.


WARNING


c While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accel- erating could cause the wheels to skid and result in an accident.


c If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder.


Wet brakes When the vehicle is washed or driven through water, the brakes may get wet. As a result, your braking distance will be longer and the vehicle may pull to one side during braking.


To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. Parking brake break-in Break-in the parking brake shoes whenever the stopping effect of the parking brake is weakened or whenever the parking brake shoes and/or drum/rotors are replaced, in order to assure the best brake performance.


Starting and driving 5-17


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKE SYSTEM (ABS) The anti-lock brake system controls the brakes so the wheels do not lock when braking abruptly or when braking on slippery surfaces. The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding. By preventing wheel lockup, the system helps the driver main- tain steering control and helps to minimize swerv- ing and spinning on slippery surfaces. Using the system Depress the brake pedal and hold it down.


WARNING


in


result


increased


Do not pump the brake pedal. Doing so may stopping distances. Normal operation The anti-lock brake system does not operate at speeds below 3 - 6 MPH (5 - 10 km/h). (The speeds vary according to road conditions.) When driving, the anti-lock brake system con- trols the wheels so they will not lock when brak- 5-18 Starting and driving


ing abruptly or when braking on a slippery road. Thus, difficult steering and swerving of the ve- hicle due to locked wheels is minimized. The system detects the wheel rotation rate and elec- tronically controls the pressure applied to each brake. Slight vibration on the brake pedal accom- panied by noise usually occurs while the ABS system is operating. Such vibration and noise encountered during abrupt braking is not a prob- lem, but indicates that the system is functioning properly. However, the pulsation may indicate that road conditions are hazardous and extra care is required while driving. Self-test feature The anti-lock brake system consists of electronic sensors and hydraulic solenoids controlled by a computer. The computer has a built-in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse. When the self-test occurs, you may hear a (cid:145)(cid:145)clunk(cid:146)(cid:146) noise and/or feel a pulsa- tion in the brake pedal. This is normal and is not an indication of any malfunction. If the computer senses any malfunction, it switches the anti-lock brake system off and turns on the ABS brake warning light on the instrument panel. The brake system then operates normally, but without anti- lock assistance.


If the light comes on during the self-test or while driving, take the vehicle to a NISSAN dealer for repair.


WARNING


c The anti-lock brake system is a sophis- ticated device, but it cannot prevent ac- cidents resulting from careless or dan- gerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces, but remember that the stopping distance on slippery sur- faces will be longer than on normal surfaces even with the anti-lock brake system. Stopping distances may also be longer on rough, gravel or snow cov- ered roads, or if you are using tire chains. Tire type and condition may also affect braking effectiveness. Always maintain a safe distance from the ve- hicle in front of you. Ultimately, the re- sponsibility for safety of self and others rests in the hands of the driver.


c Tire type and condition of tires may also


affect braking effectiveness.


c When replacing tires, install the speci-


fied size of tires on all four wheels.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


c When installing a spare tire, make sure it is the proper size and type as speci- fied on the tire placard. For tire placard location information, refer to (cid:147)Tire plac- ard(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.


c Refer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) sec- tion of this manual.


TRACTION CONTROL SYSTEM (TCS) (if so equipped)


When accelerating on slippery surfaces the tire may spin or slip. With the vehicle traction control system (TCS), sensors detect these movements and control the braking and engine output to help improve vehicle stability while accelerating. c When the traction control system is operat- ing, the slip indicator in the instrument panel blinks.


c If the slip indicator blinks, the vehicle is un- der slippery conditions. Be sure to drive carefully. See (cid:147)Slip indicator light(cid:148) and (cid:147)Trac- tion control system (TCS) off indicator light(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual.


c If a malfunction occurs in the system, lights


the come on in the meter panel.


indicator


and


As long as these lights are on, the traction control function is canceled. The vehicle will behave like a vehicle without the system.


WARNING


c The traction control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques. Reduce vehicle speed and be especially careful when driving and cornering on slippery sur- faces and always drive carefully.


c If brake related parts such as brake pads, rotors and calipers are not stan- dard equipment or are extremely dete- riorated, the traction control system may not operate properly and the indicator light may come on.


c Do not modify the vehicle(cid:146)s suspension. If suspension parts such as shock ab- sorbers, struts, springs and bushings are not standard equipment or are ex- tremely deteriorated, the traction con- trol system may not operate properly and the indicator light may come on.


Starting and driving 5-19


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


c When driving on extremely inclined sur- faces such as higher banked corners, the traction control system may not op- indicator erate properly and the light may come on. Do not drive on these types of roads.


c If wheels or tires other than the recom- mended ones are used, the traction control system may not operate prop- erly and the indicator light may come on.


c The traction control system is not a sub- stitute for winter tires or tire chains on a snow covered road.


VEHICLE DYNAMIC CONTROL (VDC) SYSTEM (if so equipped)


When accelerating or driving on slippery sur- faces, the tires may spin or slide. With the Vehicle Dynamic Control (VDC) system, sensors detect these movements and control the braking and engine output to help improve vehicle stability. c When the vehicle dynamic control (VDC) system is operating, the slip indicator in the instrument panel blinks.


c If the slip indicator blinks, the road condi- tions are slippery. Be sure to adjust your speed and driving to these conditions. See (cid:147)Slip indicator light(cid:148), and (cid:147)Vehicle dynamic control (VDC) off indicator light(cid:148) in the (cid:147)In- struments and controls(cid:148) section.


c Indicator light


and


in the system, indicator lights come


If malfunction occurs the on in the instrument panel. As long as these indicator lights are on, the traction control function is canceled.


If the vehicle is operated with the vehicle dynamic control system OFF using the VDC OFF switch, VDC functions will be turned off. The VDC sys- tem will still try to transfer power from a slipping drive wheel to one with more traction when the VDC system switch is OFF. The Slip indicator will flash if wheel spin is detected. The ABS will still operate with the VDC system off.


5-20 Starting and driving


When the VDC system is operating, you may feel a pulsation in the brake pedal and hear a noise or vibration from under the hood. This is normal and indicates that the VDC system is working prop- erly.


The computer has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle forward or in reverse at a slow speed. When the self-test occurs, you may hear a clunk noise and/or feel a pulsation in the brake pedal. This is normal and is not an indication of a malfunction.


WARNING


c The vehicle dynamic control system is designed to help improve driving stabil- ity but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques. Reduce vehicle speed and be especially careful when driving and cornering on slippery sur- faces and always drive carefully.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


c If wheels or tires other than the recom- mended ones are used, the vehicle dy- namic control system may not operate properly and the vehicle dynamic con- trol off indicator light may come on.


c The vehicle dynamic control system is not a substitute for winter tires or tire chains on a snow covered road.


c If brake related parts such as brake pads, rotors and calipers are not stan- dard equipment or are extremely dete- riorated, the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indica- tor light may come on.


c Do not modify the vehicle(cid:146)s suspension. If suspension parts such as shock ab- sorbers, struts, springs, stabilizer bars and bushings are not NISSAN approved for your vehicle or are extremely dete- riorated the vehicle dynamic control system may not operate properly. This could adversely affect vehicle handling performance, and the VDC OFF indica- tor light may come on.


c When driving on extremely inclined sur- faces such as higher banked corners, the vehicle dynamic control system may not operate properly and the VDC OFF indicator light may come on. Do not drive on these types of roads.


c When driving on an unstable surface such as a turntable, ferry, elevator or ramp, the vehicle dynamic control off indicator light may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface


COLD WEATHER DRIVING


FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply de-icer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole. ANTI-FREEZE In the winter when it is anticipated that the tem- perature will drop below 32(cid:176)F (0(cid:176)C), check the anti-freeze to assure proper winter protection. For details, see (cid:145)(cid:145)Engine cooling system(cid:146)(cid:146) in the (cid:145)(cid:145)Main- tenance and do-it-yourself(cid:146)(cid:146) section of this manual. BATTERY If the battery is not fully charged during extremely cold weather conditions, the battery fluid may freeze and damage the battery. To maintain maxi- mum efficiency, the battery should be checked regularly. For details, see (cid:145)(cid:145)Battery(cid:146)(cid:146) in the (cid:145)(cid:145)Mainte- nance and do-it-yourself(cid:146)(cid:146) section of this manual. DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see (cid:145)(cid:145)Changing engine coolant(cid:146)(cid:146) in the (cid:145)(cid:145)Maintenance and do-it-yourself(cid:146)(cid:146) section of this manual.


Starting and driving 5-21


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pave- ment. However, the performance of these tires will be substantially reduced in snowy and icy conditions. If you operate your ve- hicle on snowy or icy roads, NISSAN recom- mends the use of MUD & SNOW or ALL SEASON TIRES on all four wheels. Please consult a NISSAN dealer for the tire type, size, speed rating and availability informa- tion.


2. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.


Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires.


3. Tire chains may be used.


5-22 Starting and driving


CAUTION


Tire chains/cables cannot be installed on P245/45R18 size tires. Installation of the tire chains/cables on P245/45R18 size tires will cause damage to the vehicle. If you plan to use tire chains/cables, you should install P225/55R17 size tires on your vehicle.


Use of tire chains may be prohibited accord- ing to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s sug- gestions. Use only SAE Class (cid:147)S(cid:148) chains. Class (cid:147)S(cid:148) chains are used on ve- hicles with restricted tire to vehicle clear- ance. Vehicles that can use Class (cid:147)S(cid:148) chains are designed to meet the minimum clear- ances between the tire and the closest ve- hicle suspension or body component re- quired to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain ten- sioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be


secured or removed to prevent the possibil- ity of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addi- tion, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. Never install tire chains on spare tires. Do not use tire chains on dry roads.


SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter: c A scraper and stiff-bristled brush to remove ice and snow from the windows and wiper blades.


c A sturdy, flat board to be placed under the


jack to give it firm support.


c A shovel to dig the vehicle out of snowdrifts. c Extra window washer fluid to refill the reser-


voir tank.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


DRIVING ON SNOW OR ICE


WARNING


c Wet ice (32(cid:176)F, 0(cid:176)C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or (cid:147)grip(cid:148) under these conditions. Try to avoid driving on wet the road is salted or sanded.


ice until


c Whatever the condition, drive with cau- tion. Accelerate and slow down with care. If accelerating or downshifting too fast, the drive wheels will lose even more traction.


c Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement.


c Allow greater following distances on


slippery roads.


c Do not use the cruise control on slip-


pery roads.


c Snow can trap dangerous exhaust gases under your vehicle. Keep snow clear of the exhaust pipe and from around your vehicle.


ENGINE BLOCK HEATER (if so equipped) An engine block heater to assist in extreme cold temperature starting is available through a NISSAN dealer.


WARNING


Do not use your heater with an un- grounded electrical two- pronged (cheater) adapters. You can be injured by an electrical shock if you use an ungrounded connection.


system or


c Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reach- ing it. Try not to brake while on the ice, and steering avoid maneuvers.


sudden


any


Starting and driving 5-23


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/07/05—tbrooks X


MEMO


5-24 Starting and driving


6 In case of emergency


Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8


If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
Towing your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Towing recommended by NISSAN . . . . . . . . . . . . . . 6-10
Vehicle recovery (freeing a stuck vehicle) . . . . . . . . . 6-11


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


FLAT TIRE


CHANGING A FLAT TIRE If you have a flat tire, follow the instructions be- low. Stopping the vehicle 1. Safely move the vehicle off the road and


away from traffic.


2. Turn on the hazard warning flashers. 3. Park on a level surface and apply the parking brake. Shift the manual transmission into R (Reverse), or the automatic transmission into P (Park).


4. Turn off the engine. 5. Raise the hood to warn other traffic and to signal professional road assistance person- nel that you need assistance.


6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle.


6-2 In case of emergency


WARNING


c Make sure the parking brake is securely applied and the manual transmission is shifted into R (Reverse), or the auto- matic transmission into P (Park).


c Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.


c Never change tires if oncoming traffic is close to your vehicle. Wait for profes- sional road assistance.


WCE0044


Blocking wheels Place suitable blocks s1 at both the front and back of the wheel diagonally opposite the flat tire s2 to prevent the vehicle from moving when it is jacked up.


WARNING


Be sure to block the wheel as the vehicle may move and result in personal injury.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


LCE0074


LCE0075


LCE0076


Getting the spare tire and tools Open the trunk. Lift the trunk floor carpeting and spare tire cover. Remove the jack s1 and wheel nut wrench s2 from the tool box. Remove the spare tire.


Type A


Type B


In case of emergency 6-3


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


c Use the correct jack-up points. Never use any other part of the vehicle for jack support.


c Never jack up the vehicle more than


necessary.


c Never use blocks on or under the jack. c Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for slip differentials.


vehicles


limited


with


c Do not allow passengers to stay in the


vehicle while it is on the jack.


c Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move.


CE1089


Jacking up vehicle and removing the damaged tire


WARNING


c Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands.


c Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The jack is designed for lifting only your vehicle during a tire change.


6-4 In case of emergency


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions.


1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground.


LCE0020
2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. Align the jack head between the two notches in the front or the rear as shown. Also fit the groove of the jack head between the notches as shown. The jack should be used on firm and level ground.


3. To lift the vehicle, securely hold the jack lever and rod with both hands. Carefully raise the vehicle until the tire clears the ground. Re- move the wheel nuts, and then remove the tire.


WCE0056


Installing the spare tire The spare tire is designed for emergency use. See specific instructions under the heading (cid:147)Wheels and tires(cid:148) in the (cid:147)Mainte- nance and do-it-yourself(cid:148) section of this manual.


1. Clean any mud or dirt from the surface be-


tween the wheel and hub.


2. Carefully put the spare tire on and tighten


the wheel nuts finger tight.


3. With the wheel nut wrench, tighten wheel nuts alternately and evenly as illustrated until they are tight.


In case of emergency 6-5


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


4. Lower


the vehicle slowly until


the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated (sA , sB , sC , sD , sE ). Lower the vehicle completely.


WARNING c Incorrect wheel nuts or


improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.


c Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.


c Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).


As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.


Wheel nut tightening torque:


80 ft-lb (108 N•m)


The wheel nuts must be kept tightened to specification at all is recom- mended that wheel nuts be tightened to specifications at each lubrication interval. 6-6 In case of emergency


times.


It


Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire placard affixed to the center console. 5. Securely store the flat tire and jacking equip-


ment in the vehicle.


6. Place the spare tire cover and the trunk floor


carpeting over the damaged tire.


7. Close the trunk.


WARNING


c Always make sure that the spare tire and jacking equipment are properly se- cured after use. Such items can become dangerous projectiles in an accident or sudden stop.


c The spare tire is designed for emer- gency use. See specific instructions un- der the heading (cid:147)Wheels and tires(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section of this manual.


JUMP STARTING


To start your engine with a booster battery, the instructions and precautions below must be fol- lowed.


WARNING


c If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.


c Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.


c Do not allow battery fluid to come into contact with eyes, skin, clothing or painted surfaces. Battery fluid is a cor- rosive sulfuric acid solution which can cause severe burns. If the fluid should come into contact with anything, imme- diately flush the contacted area with water.


c Keep battery out of


children.


the reach of


c The booster battery must be rated at 12
volts. Use of an improperly rated battery can damage your vehicle.


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


c Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting.


c Do not attempt to jump start a frozen battery. It could explode and cause se- rious injury.


c Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it.


WARNING


Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury.


1.


If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries near each other. Do not allow the two vehicles to touch.


WCE0054
2. Apply the parking brake. Move the shift lever to N (Neutral) (manual transmission) or to P (Park) (automatic transmission). Switch off all unnecessary electrical systems (lights, heater, air conditioner, etc.).


3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.


4. Connect jumper cables in the sequence il-


lustrated (sA , sB , sC , sD ).


In case of emergency 6-7


Z REVIEW COPY—2005 Maxima (max) Owners Manual—USA_English (nna) 03/08/05—tbrooks X


8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.


PUSH STARTING


CAUTION


c Automatic transmission models cannot be push-started or tow-started. At- tempting to do so may cause transmis- sion damage.


c Three-way catalyst equipped models should not be started by pushing. The three-way catalyst may be damaged.


c Never try to start the vehicle by towing it. When the engine starts, the forward surge could cause the vehicle to collide with the tow vehicle.


CAUTION


c Always connect positive (1) to positive (1) and negative (2) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) (cid:151) not to the battery.


c Make sure the jumper cables do not

Loading...
x