2004 Nissan Maxima Owners Manual

checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte-

nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148). BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step.

2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, stop the engine. Keep the pedal depressed for about 30 seconds. The pedal height should not change.

4. Run the engine for one minute without de- pressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is re- leased from the booster.

If the brakes do not operate properly, have the brakes checked by a NISSAN dealer.

FUSES

LDI0327

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not come on, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the engine hood.

Maintenance and do-it-yourself 8-23

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

3. Remove the fuse box cover by pushing the

tab and lifting the cover up.

4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.

5. 6.

WDI0200
If the fuse is open, replace it with a new fuse. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.

8-24 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

4.

LDI0328
If the fuse is open, replace it with a known good fuse.

5. Push the fuse box cover to install. 6.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

PASSENGER COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight

switch are OFF.

2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller.

Maintenance and do-it-yourself 8-25

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

KEYFOB BATTERY REPLACEMENT

5. Press the LOCK button, then the UNLOCK button two or three times to check the key- fob operation.

If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly ap- proved by the manufacturer for compliance could void the user(cid:146)s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

Replace the battery in the keyfob as follows: s1 Open the lid using a coin. s2 Remove the battery.

8-26 Maintenance and do-it-yourself

s3

WPD0136
Install a new battery with the (cid:147)+(cid:148) facing down.

Recommended battery: Sanyo CR2025 or equivalent. s4 Close the lid securely.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

LIGHTS

HEADLIGHTS Replacing the xenon headlight bulb

WARNING

cHIGH VOLTAGE

When xenon headlights are on, they pro- duce a high voltage. To prevent an electric shock, never attempt to modify or disas- semble. Always have your xenon head- lights replaced at a NISSAN dealer. For additional information, see (cid:147)Headlight and turn signal switch(cid:148) in the (cid:147)Instru- ments and controls(cid:148) section. Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Be- cause the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.

CAUTION

c Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.

c Do not leave the headlight assembly open without a bulb installed for a long period of time. Dust, moisture, smoke, etc. entering the headlight body may affect bulb performance. Remove the bulb from the headlight assembly just before a replacement bulb is installed. c Only touch the plastic base when han- dling the bulb. Never touch the glass envelope. Touching the glass could sig- nificantly affect bulb life and/or head- light performance.

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c Use the same number and wattage as

originally installed: Low beam:

Wattage: 55
Bulb no.: 9012*

High beam:

Wattage: 55
Bulb no.: 9012*

*: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.

Maintenance and do-it-yourself 8-27

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.*

Headlight assembly

High/low (Halogen) High/low (Xenon) Day time running lamp Park/Turn Cornering

Front fog light Front personal/map lights Console box illumination Glove box light (if so equipped) Vanity mirror light Step light Rear personal lamps Rear console box light High-mounted stop light Trunk light Rear combination light

Tail/Stop/Turn Backup (reversing) Sidemarker License plate light

55
35
(cid:150)

27/8
27
55
3.4
(cid:150) 3.4
2.1
3.8
3.4

27/5
13

9012
D2S 1156

1157NA 3156K

H3
(cid:150) 194
158
(cid:150) 194
(cid:150)

W5W 949
158

3057K

912
168
168

*: Always check with the Parts Department at a NISSAN dealer for the latest parts information.

8-28 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Rear personal lights Step light

1. Map light 2. 3. 4. Cornering light 5. 6. 7. 8. High-mount stoplight 9. Headlamp assembly 10. Fog light

Rear combination light License plate light Trunk light

LDI0391

Maintenance and do-it-yourself 8-29

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WDI0263

LDI0338

LDI0339

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.

first remove the lens,

Indicates bulb removal Indicates bulb installation

Front personal/map lights (cid:150) Type A

Use a cloth s1 to protect the housing.

Front personal/map lights (cid:150) Type B

Use a cloth s1 to protect the housing.

8-30 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Vanity mirror light

Use a cloth s1 to protect the housing.

Use a cloth s1 to protect the housing.

Step light

WDI0340

LDI0341

Rear personal light

Use a cloth s1 to protect the housing.

WDI0342

Maintenance and do-it-yourself 8-31

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Rear console box light

Squeeze the tabs on the connector. Pull out the bulb.

LDI0397

Trunk light

WDI0343

High-mounted stop light

WDI0344

8-32 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

WHEELS AND TIRES

If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label (this label is also known as the tire placard) under the 9Recommended Cold Tire Inflation Pressure9
heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. Incorrect tire pressure, including under in- flation, may adversely affect tire life and vehicle handling.

WARNING

c Improperly inflated tires can fail sud-

denly and cause an accident.

c The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components.

c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

c Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury.

Maintenance and do-it-yourself 8-33

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

type a

LDI0392

8-34 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

s6

and s7 . Spare tire size or compact spare tire size (if so equipped)

type b

Tire and loading information label (for US) s1 Seating capacity: The maximum number of occupants that should be seated in the ve- hicle. This example shows 2 for front seats, 3
for rear seats, total 5 occupants.

s2 Vehicle load limit: See loading information in information

the Technical and consumer section.

s3 Original tire size: The size of the tires origi- nally installed on the vehicle at the factory.

LDI0390

s4 Recommended cold tire inflation pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best tire wear and vehicle handling characteristics based on the ve- hicles GVWR.

s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later in this

section.

Maintenance and do-it-yourself 8-35

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.

6. 7. Check the pressure of all other tires, includ-

ing the spare.

Size

P225/55R17
P245/45R18
P225/55R17
P245/45R18
T145/80*17

Cold Tire Infla- tion Pressure 230 kPa, 33 PSI 220 kPa, 32 PSI 230 kPa, 33 PSI 220 kPa, 32 PSI 420 kPa, 60 PSI

Front Original Tire Rear Original Tire Spare Tire

WDI0394

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

LDI0393

Checking tire pressure 1. Remove the valve stem cap from the tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leakage.

3. Remove the gauge.

4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label.

8-36 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WDI0395
6. Two- or three-digit number: This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. Tire speed rating. You should not drive the

vehicle faster than the tire speed rating.

(1) Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is designed for

passenger vehicles.

2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.

3. Two-digit number: This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width.

4. R: The 9R9 stands for radial. 5. Two-digit number: This number is the wheel

or rim diameter in inches.

Maintenance and do-it-yourself 8-37

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

(5) Maximum load rating This number indicates the maximum load in kilo- grams and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire. (6) Term of (cid:148)tubeless(cid:148) or (cid:148)tube type(cid:148) Indicates whether the tire requires an inner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). (7) The word (cid:148)radial(cid:148) The word 9radial9 is shown if the tire has radial structure. (8) Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout Intended Outboard Sidewall is (1) the sidewall that contains a white- wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the outward facing sidewall of an asymmetrical tire that has a par- ticular side that must always face outward when mounted on a vehicle.

this section,

(2) TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Number.

2. Two-digit code: Manufacturer(cid:146)s identifica-

tion mark

3. Two-digit code: Tire size

4. Three-digit code: Tire type code (Optional)

5. Three-digit code: Date of Manufacture

8-38 Maintenance and do-it-yourself

WDI0396
6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003.

(3) Tire ply composition and material The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. (4) Maximum permissible inflation pressure This number is the greatest amount of air pres- sure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

TYPES OF TIRES

WARNING

c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and avail- ability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rat- ing of the tire. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ- ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas.

Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.

If you do not,

If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing

studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use only SAE class (cid:147)S(cid:148) chains. Class (cid:147)S(cid:148) chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class (cid:147)S(cid:148) chains are de- signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tires. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the pos- sibility of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and perfor- mance may be adversely affected.

Maintenance and do-it-yourself 8-39

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Tire chains must be installed only on the front wheels and not on the rear wheels. Never install tire chains on a TEMPORARY USE ONLY spare tire. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress.

WDI0258

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km).

See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual for tire replacing proce- dures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

80 ft-lb (108 N•m)

8-40 Maintenance and do-it-yourself

The wheel nuts must be kept tightened to specifications at all times. It is recom- mended that wheel nuts be tightened to specification at each tire rotation interval.

WARNING

c After rotating the tires, check and ad-

just the tire pressure.

c Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

c Do not include the spare tire in the tire

rotation.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

c The original tires have built-in tread wear indicators. When the wear indica- tors are visible, the tire(s) should be replaced.

c Improper service of the spare tire may result in serious personal injury. If it is necessary to repair the spare tire, con- tact a NISSAN dealer.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

WDI0259

1. Wear indicator 2. Location mark Tire wear and damage

WARNING

c Tires should be periodically inspected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.

WARNING

c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.

c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.

this manual

with

the

Maintenance and do-it-yourself 8-41

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. is not

retread tires

c The use of recommended. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage. c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .

8-42 Maintenance and do-it-yourself

Care of wheels c Wash the wheels when washing the vehicle

to maintain their appearance.

c Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

c Do not use abrasive cleaners when washing

the wheels.

c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

Spare tire (TEMPORARY USE ONLY spare tire) (if so equipped) Observe the following precautions if the TEM- PORARY USE ONLY spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident:

WARNING

c The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid possible tire or differen- tial damage.

c Drive carefully while the TEMPORARY USE ONLY spare tire is installed. Avoid sharp turns and abrupt braking while driving.

c Periodically check spare tire inflation pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar).

c With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 MPH (80 km/h). c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

c Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear.

c Do not use the spare tire on other

vehicles.

c Do not use more than one spare tire at

the same time.

c Do not tow a trailer when the TEMPO- RARY USE ONLY spare tire is installed.

CAUTION

c Do not use tire chains on a TEMPO- RARY USE ONLY spare tire. Tire chains will not fit properly and may cause dam- age to the vehicle.

c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught.

Maintenance and do-it-yourself 8-43

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

MEMO

8-44 Maintenance and do-it-yourself

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation . . . . . . . . . . . 9-5
Recommended SAE viscosity number . . . . . . . . . . . . 9-6
Air conditioner system refrigerant and lubricant recommendations . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8

When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification number (VIN) plate . . . . . . . . . . 9-9
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
F.M.V.S.S. certification label . . . . . . . . . . . . . . . . . . . . 9-10
Emission control information label . . . . . . . . . . . . . . . 9-10

Tire placard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Air conditioner specification label. . . . . . . . . . . . . . . . 9-11
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12
Determining vehicle load capacity . . . . . . . . . . . . . . . 9-12
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Towing load/specification chart . . . . . . . . . . . . . . . . . 9-15
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-18
Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-19
Readiness for inspection/maintenance (I/M) test . . . . . 9-19
Owner(cid:146)s Manual/Service Manual order information . . . 9-20
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-21

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the (cid:147)Maintenance and do-it-yourself(cid:148) section to determine the proper refill capacity.

Fuel Engine oil *8

Drain and Refill

Capacity (Approximate) US measure 20 gal

Imp measure 16-5/8 gal

With oil filter change

Without oil filter change

4-1/4 qt

3-7/8 qt

3-1/2 qt

3-1/4 qt

7-1/4 qt

4 pt

8-5/8 qt

4-7/8 pt

Cooling system

With reservoir

Manual transmission gear oil Automatic transmission fluid

4 Speed

5 Speed

Liter 75.8

4.0

3.7

8.2

2.3

Recommended Fluids and Lubricants

Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1

(cid:149) API Certification Mark *2 *3
(cid:149)API grade SL, Energy Conserving *2 *3
(cid:149) ILSAC grade GF-III*2 *3

50% Genuine NISSAN Long Life Anti-freeze Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Manual Transmission Fluid HQ Multi 75W-85 or equivalent

Refill to the proper level according to the instructions in the (cid:147)Maintenance and do-it-yourself(cid:148) section.

Genuine Nissan Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Trans- mission Fluid.*4
Genuine Nissan Matic K ATF *5
Genuine NISSAN PSF or equivalent.*9
Genuine NISSAN Super Heavy Duty Brake Fluid*6 or equivalent DOT 3 (US FMVSS No. 116) NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a)*7
NISSAN A/C System Lubricant Type DH-PS or equivalent*7
Genuine NISSAN Windshield Washer Concentrate Cleaner & Anti-freeze or equivalent

Power steering fluid (PSF) Brake and clutch fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system lubricants Windshield washer fluid *1: For further details, see (cid:147)Fuel recommendation.(cid:148) *2: For further details, see (cid:147)Engine oil and oil filter recommendations.(cid:148) *3: For further details, see (cid:147)Recommended SAE engine oil viscosity.(cid:148) *4: Dexron(cid:153) III/Mercon(cid:153) or equivalent may also be used. Outside the Continental United States and Alaska contact a NISSAN dealership for more information regarding suitable fluids, including recommended brand(s) of Dexron(cid:153) III/Mercon(cid:153) Automatic Transmission Fluid. *5: Using automatic transmission fluid other than Genuine Nissan Matic K ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic transmission, which is not covered by the NISSAN new vehicle warranty. *6: Available in mainland USA through your NISSAN dealer. *7: For further details, see (cid:147)Air conditioner specification label.(cid:148) *8: For further details, see (cid:147)Changing engine oil.(cid:148) *9: For Canada, NISSAN Automatic Transmission Fluid (ATF), Dexron(cid:153) III/Mercon(cid:153), or equivalent ATF may also be used.

(cid:151) (cid:151) (cid:151) (cid:151)

(cid:151) (cid:151) (cid:151) (cid:151)

(cid:151) (cid:151) (cid:151) (cid:151)

9-2 Technical and consumer information

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).

For improved vehicle performance, NISSAN rec- ommends the use of unleaded premium gasoline with an octane rating of at least 91 AKI number (Research octane number 96).

CAUTION

c Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

c Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.

Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available.

Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com- patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.

If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

c If an oxygenate-blend other

c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and

corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.

fuels,

oxygenate-blend

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips In most parts of North America, you should use unleaded gasoline with an octane rating of at Technical and consumer information 9-3

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

least 87 AKI (Anti-Knock Index) number. How- ever, you may use unleaded gasoline with an octane rating as low as 85 AKI (Anti-Knock Index) number in high altitude areas [over 4,000 ft (1,219 m)] such as: Colorado, Montana, New Mexico, Utah, Wyoming, northeastern Nevada, southern Idaho, western South Dakota, western Nebraska, and the part of Texas which is directly south of New Mexico. Using unleaded gasoline with an octane rating lower than stated above can cause persistent, heavy (cid:147)spark knock.(cid:148) ((cid:147)Spark knock(cid:148) is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible.

ignition timing may result

Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer.

9-4 Technical and consumer information

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the cor- rect quality and viscosity to ensure satisfactory engine life and performance. NISSAN recom- mends the use of a low friction oil (energy con- serving oil) in order to improve fuel economy and conserve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage.

Only those engine oils with the American Petro- leum Institute (API) CERTIFICATION MARK on

WTI0082

the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories.

If you cannot find engine oil with the API CERTI- FICATION MARK, use API grade SL Energy Conserving oil. An oil with a single designation SL, or in combination with other categories (for example, SL/CF) may also be used if one with the API CERTIFICATION MARK cannot be found. An ILSAC grade GF-III oil can also be used.

NISSAN recommends mineral based oils. These oils must, however, meet the API quality and SAE viscosity ratings specified for your vehicle.

Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. The chart (cid:147)Rec- ommended SAE viscosity number(cid:148) shows the recommended oil viscosities for the expected ambient temperatures. Choosing an oil viscosity other than that recommended could cause seri- ous engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in (cid:147)Change intervals(cid:148).

Technical and consumer information 9-5

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle warranty. Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: c repeated short distance driving at cold out-

side temperatures

c driving in dusty conditions c extensive idling c towing a trailer

9-6 Technical and consumer information

ATI1028

RECOMMENDED SAE VISCOSITY NUMBER c SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0(cid:176)F (-18(cid:176)C).

AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the lubricant, NISSAN A/C system oil DH-PS or the exact equivalents.

CAUTION

The use of any other refrigerant or lubri- cant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner system components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth(cid:146)s ozone layer. Although this refrigerant does not affect the earth(cid:146)s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

SPECIFICATIONS

ENGINE

Model

Type Cylinder arrangement Bore x Stroke Displacement Firing order

Idle speed

M/T A/T (in (cid:147)N(cid:148) position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle

Spark plug

Spark plug gap (Nominal)

Camshaft operation

VQ35DE

Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60(cid:176)

in (mm) 3.760 x 3.205 (95.5 x 81.4)

cu in (cm3) 213.45 (3,498) 1(cid:150)2(cid:150)3(cid:150)4(cid:150)5(cid:150)6

See the (cid:147)Emission Control label(cid:148) on the underside of the hood.

Standard PLFR5A-11

Hot PLFR4A-11
Cold PLFR6A-11

in (mm) 0.043 (1.1)

Timing chain

The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Technical and consumer information 9-7

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Wheels

Tires

Spare tire

Speed rating

17 x 7JJ 18 x 7.5JJ

P225/55R17
P245/45R18

Temporary Full size

T145/80*17
17(cid:148) or 18(cid:148)

17(cid:148) 18(cid:148)

*: (cid:147)R(cid:148) or (cid:147)D(cid:148) depending on tire manufacturer

Overall length Overall width Overall height Front tread

17 inch tire 18 inch tire

Rear tread

17 inch tire 18 inch tire

Wheelbase

Gross vehicle weight rating Gross axle weight rating

Front Rear

in (mm) 193.5(4,915) in (mm) 71.7(1,821) 58.3(1,481) in (mm)

in (mm) in (mm)

61.4(1,559) 61.0(1,549)

61.6(1,565) in (mm) in (mm) 61.2(1,554) in (mm) 111.2(2,824) lb (kg) See the (cid:147)F.M.V.S.S.

certification label(cid:148) on the center pillar between the driver(cid:146)s side front and rear doors.

lb (kg) lb (kg)

9-8 Technical and consumer information

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle(cid:146)s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

VEHICLE IDENTIFICATION

LTI0069
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

LTI0070
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.

Technical and consumer information 9-9

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WTI0049

LTI0071

LTI0072

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

F.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Standard (F.M- .V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Num- ber (VIN), etc. Review it carefully.

EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.

information label

is at-

9-10 Technical and consumer information

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

INSTALLING FRONT LICENSE PLATE

LTI0073

TIRE PLACARD The cold tire pressure is shown on the tire plac- ard. The tire placard is located under the center console lid.

LTI0074
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed as shown.

Technical and consumer information 9-11

LTI0075

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Use the following steps to mount the front license plate: Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag: c License plate bracket c License plate bracket screws x 2
c License plate screws x 2
c Screw grommets x 2
1. Make a shallow hole in the bumper fascia at the location marks (small dimples) using a 0.39 in (10 mm) drill. To avoid damaging the area behind the fascia, apply only light pres- sure to the drill. Insert the grommets into the holes in the bumper fascia. Insert a small flat-bladed screwdriver into the grommet hole to turn the threaded part of the grommet 90(cid:176).

2.

3.

4. Mount the license plate bracket using the

two longer screws.

5. Use the two shorter hex head screws to mount the license plate to the license plate bracket.

9-12 Technical and consumer information

VEHICLE LOADING INFORMATION

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a colli- sion, people riding in these areas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a

seat and using a seat belt properly.

TERMS It is important to familiarize yourself with the fol- lowing terms before loading your vehicle: c Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and op- tional equipment, fluids, emergency tools, and spare tire assembly. This weight does not include passengers and cargo.

c GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

c GVWR (Gross Vehicle Weight Rating) - maximum total weight (load) limit specified for the vehicle.

c GAWR (Gross Axle Weight Rating) - maxi- mum weight (load) limit specified for the front or rear axle.

DETERMINING VEHICLE LOAD CAPACITY The load capacity of this vehicle is determined by weight, not by available cargo space. For ex- ample, a luggage rack, bike carrier, cartop carrier or similar equipment does not increase load car- rying capacity of your vehicle.

To determine vehicle load capacity:

Vehicle weight can be determined by using a commercial-grade scale, found at places such as a truck stop, gravel quarry, grain elevator, or a scrap metal recycling facility.

1. Determine the curb weight of your vehicle.

2. Compare the curb weight amount to the GVWR specified for your vehicle to deter- mine how much more weight your vehicle can carry.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

3. After loading (cargo and passengers), re- weigh your vehicle to determine if either GVWR or GAWR for your vehicle is ex- ceeded. remove cargo as necessary. If either the front or rear GAWR is exceeded, shift the load or remove cargo as necessary.

If GVWR is exceeded,

LOADING TIPS c The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S. certi- fication label.

c Do not load the front and rear axle to the

GAWR. Doing so will exceed the GVWR.

WARNING

c Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or col- lision, unsecured cargo could cause personal injury.

c Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

c Overloading not only can shorten the life of your vehicle and the tire, but can also cause unsafe vehicle handling and longer braking distances. This may cause a premature tire failure which could result in a serious accident and personal injury. Failures caused by overloading are not covered by the ve- hicle(cid:146)s warranty.

TOWING A TRAILER

Your new vehicle was designed to be used pri- marily to carry passengers and cargo. Remember that towing a trailer places additional loads on your vehicle(cid:146)s engine, drive train, steering, brak- ing and other systems. A Nissan Trailer Towing Guide (U.S. only) is available from a NISSAN dealer. This guide in- cludes information on trailer towing ability and the special equipment required for proper towing. MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed the value specified in the Towing Load/Specification Chart found later in this section. The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than specified or using improper towing equipment could adversely af- fect vehicle handling, braking and performance.

The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads, but also the places you plan to tow. Tow weights appro- priate for level highway driving may have to be reduced on very steep grades or in low traction situations (for example, on slippery boat ramps).

Technical and consumer information 9-13

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

CAUTION

Vehicle damage resulting from improper towing procedures are not covered by NISSAN warranties. A NISSAN Trailer Towing Guide (U.S. only) containing infor- mation on trailer towing ability and the special equipment required may be ob- tained from a NISSAN dealer.

9-14 Technical and consumer information

CA0009

TI1012M

Tongue load Keep the tongue load between 9 - 11 percent of the total trailer load within the maximum tongue load limits shown in the following Towing Load/Specification Chart. If the tongue load be- comes excessive, rearrange cargo to allow for proper tongue load.

Maximum gross vehicle weight/maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating (GVWR) shown on the F. M. V. S. S. certification label. The gross vehicle weight equals the com- bined weight of the unloaded vehicle, passen- gers, luggage, hitch, trailer tongue load and any other optional equipment. In addition, front or rear gross axle weight must not exceed the gross axle weight rating (GAWR) shown on the F. M. V. S. S. certification label.

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

TOWING LOAD/SPECIFICATION CHART

TOWING LOAD / SPECIFICATION CHART

MAXIMUM TOWING

LOAD

MAXIMUM TONGUE

LOAD

UNIT: lb (kg)

1,000 (454)

100 (45)

TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer. A genuine NISSAN trailer hitch is available from your NISSAN dealer. Make sure the trailer hitch is securely attached to the vehicle, to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks.

CAUTION

c Do not use axle-mounted hitches. c The hitch should not be attached to or the impact-

the operation of

affect absorbing bumper.

c Do not modify the vehicle exhaust sys- tem, brake system, etc. to install a trailer hitch.

c To reduce the possibility of additional damage if your vehicle is struck from the rear, where practical, remove the hitch and/or receiver when not in use. c After the hitch is removed, seal the bolt holes to prevent exhaust fumes, water or dust from entering the passenger compartment.

c Regularly check that all trailer hitch mounting bolts are securely mounted.

Tire pressures c When towing a trailer, inflate the vehicle tires to the recommended cold tire pressure indi- cated on the tire placard.

c Trailer tire condition, size,

load rating and proper inflation pressure should be in accor- dance with the trailer and tire manufacturer(cid:146)s specifications.

Safety chains Always use suitable safety chains between your vehicle and the trailer. The safety chains should be crossed and should be attached to the hitch,

not to the vehicle bumper or axle. Be sure to leave enough slack in the chains to permit turning corners. Trailer lights Trailer lights should comply with federal and/or local regulations. When wiring the vehicle for towing, connect the stop and tail light pickup into the vehicle electrical circuit. Trailer brakes If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed.

WARNING

Never connect a trailer brake system di- rectly to the vehicle brake system. Pre-towing tips c Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition.

c Always secure items in the trailer to prevent

load shift while driving.

Technical and consumer information 9-15

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

c Be certain your rearview mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle. Trailer towing tips In order to gain skill and an understanding of the vehicle(cid:146)s behavior, you should practice turning, stopping and backing up in an area which is free from traffic. Steering stability and braking perfor- mance will be somewhat different than under normal driving conditions. c Always secure items in the trailer to prevent

load shift while driving.

c Avoid abrupt starts, acceleration or stops. c Avoid sharp turns or lane changes. c Always drive your vehicle at a moderate

speed.

c Always block the wheels on both vehicle and trailer when parking. Parking on a slope is not recommended; however, if you must do so, and if your vehicle is equipped with an automatic transmission, first block the wheels and apply the parking brake, and then move the transmission shift selector lever into the P (Park) position. If you move the shift selector lever to the P (Park) posi- tion before blocking the wheels and applying

9-16 Technical and consumer information

the parking brake, could occur.

transmission damage

make a larger than normal turning radius during the turn.

c When going down a hill, shift into a lower gear and use the engine braking effect. When going up a long grade, downshift the transmission to a lower gear and reduce speed to reduce chances of engine over- loading and/or overheating. However, for long steep grades, do not stay in 1st or 2nd gear when driving above 35 MPH (56 km/h). c If the engine coolant rises to an extremely high temperature when the air conditioner system is on, turn off the air conditioner. Coolant heat can be additionally vented by opening the windows, switching the fan control to high and setting the temperature control to the HOT position.

c Trailer towing requires more fuel than normal

circumstances.

c Avoid towing a trailer for your vehicle(cid:146)s first

500 miles (805 km).

c Have your vehicle serviced more often than at intervals specified in the recommended Maintenance Schedule in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148).

c When making a turn, your trailer wheels will be closer to the inside of the turn than your vehicle wheels. To compensate for this,

c Crosswinds and rough roads will adversely affect vehicle/trailer handling, possibly caus- ing vehicle sway. When being passed by larger vehicles, be prepared for possible changes in crosswinds that could affect ve- hicle handling. If swaying does occur, firmly grip the steering wheel, steer straight ahead, and immediately (but gradually) reduce ve- hicle speed. This combination will help sta- bilize the vehicle. Never increase speed.

c Be careful when passing other vehicles. Passing while towing a trailer requires con- siderably more distance than normal pass- ing. Remember, the length of the trailer must also pass the other vehicle before you can safely change lanes.

c To maintain engine braking efficiency and electrical charging performance, do not use 5th gear (manual transmission) or overdrive (automatic transmission).

c Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in reduced braking efficiency.

When towing a trailer, transmission oil/fluid should be changed more fre-

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

Automatic Transmission To tow a vehicle equipped with an automatic transmission, an appropriate vehicle dolly MUST be placed under the towed vehicle(cid:146)s drive wheels. Always follow the dolly manufacturer(cid:146)s recommendations when using their product. Manual Transmission c Always tow with the manual transmission in

Neutral.

c After towing 500 miles, start and idle the engine with the transmission in Neutral for two minutes. Failure to idle the engine after every 500 miles of towing may cause dam- age to internal transmission parts.

quently. For additional information, see the (cid:147)Maintenance and do-it-yourself(cid:148) section earlier in this manual. FLAT TOWING Towing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home.

CAUTION

c Failure to follow these guidelines can result in severe transmission damage. c Whenever flat towing your vehicle, al-

ways tow forward, never backward.

c DO NOT tow any automatic transmis- sion vehicle with all four wheels on the ground (flat towing). Doing so WILL DAMAGE internal transmission parts due to lack of transmission lubrication. c For emergency towing procedures refer to (cid:147)Towing recommended by NISSAN(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

UNIFORM TIRE QUALITY GRADING

DOT (Department of Transportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades.

Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

Treadwear

Treadwear grade is a comparative rating based on tire wear rate when tested under controlled conditions on specified government test courses. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the govern- ment course as a tire graded 100. However, relative tire performance depends on actual driv- ing conditions, and may vary significantly due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction AA, A, B and C

The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire(cid:146)s ability to stop on wet pavement as mea- sured under controlled conditions on specified government test surfaces of asphalt and con- crete. A tire marked C may have poor traction performance.

Technical and consumer information 9-17

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

WARNING

WARNING

The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, ei- ther separately or in combination, can cause heat build-up and possible tire failure.

The traction grade assigned to your ve- hicle tires is based on straight-ahead braking traction tests and does not in- clude acceleration, cornering, hydroplan- ing or peak traction characteristics.

Temperature A, B and C

Temperature grades are A (the highest), B, and C. They represent a tire(cid:146)s resistance to heat build-up, and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high tem- perature can cause tire material to degenerate, reducing tire life. Excessive temperatures can lead to sudden tire failure. Grade C corresponds to a performance level which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades A and B rep- resent higher levels of performance on laboratory test wheels than the minimum required by law.

9-18 Technical and consumer information

EMISSION CONTROL SYSTEM WARRANTY

Your NISSAN vehicle is covered by the following emission warranties: For USA 1. Emission Defects Warranty 2. Emissions Performance Warranty Details of these warranties may be found with other vehicle warranties in your Warranty Infor- mation Booklet which comes with your NISSAN vehicle. If you did not receive a Warranty Informa- tion Booklet, or it is lost, you may obtain a re- placement by writing to: c Nissan North America, Inc.

Consumer Affairs Department P.O. Box 191
Gardena, CA 90248-0191

For Canada Emission Control System Warranty Details of these warranties may be found with other vehicle warranties in your Warranty Infor- mation Booklet which comes with your NISSAN vehicle. If you did not receive a Warranty Informa- tion Booklet, or it is lost, you may obtain a re- placement by writing to: c Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario, L4W 4Z5

Z REVIEW COPY:—2004 Maxima (max) Owners Manual (owners)—USA English (nna) 10/20/03—arosenma X

REPORTING SAFETY DEFECTS (US only)

READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the Na- tional Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or NISSAN. To contact NHTSA, you may call the Auto Safety Hotline toll-free at 1-888-327-4236. You may also write to: NHTSA, U.S. Department of Trans- portation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline. You may notify NISSAN by contacting our Con- sumer Affairs Department, toll-free, at 1-800- NISSAN-1. In Hawaii call 1-808-836-0888.

Due to legal requirements in some states and Canadian Provinces, your vehicle may be re- quired to be in what is called the (cid:147)ready condi- tion(cid:148) for an Inspection/Maintenance (I/M) test of the emission control system.

The vehicle is set to the (cid:147)ready condition(cid:148) when it is driven through certain driving patterns. Usually, the ready condition can be obtained by ordinary usage of the vehicle.

If a powertrain system component is repaired or the battery is disconnected, the vehicle may be reset to a (cid:147)not ready(cid:148) condition. Before taking the I/M test, drive the vehicle through the following pattern to set the vehicle to the ready condition. If you cannot or do not want to perform the driving pattern, a NISSAN dealer can conduct it for you.

WARNING