Download PDF Manual

I If done incorrectly, jump starting can lead to a battery explosion, resulting in severe injury or death. It could also damage your vehicle.


I Explosive hydrogen gas is always present in the vicinity of the battery. Keep all sparks and flames away from the battery.


I Do not allow battery fluid to come into contact with eyes, skin, cloth or painted surfaces. Battery fluid is a corrosive sulphuric acid solution which can cause severe burns. If the fluid should come into contact with anything, immediately flush the con- tacted area with water. I Keep battery out of


the reach of


children.


Z 02.7.12/A33-D/V5.0 X


SCE0040


Stowing the damaged tire and tools Securely store the spare tire and jacking equipment in the vehicle.


WARNING


I Always make sure that the spare tire and jacking equipment are properly secured after use. Such items can become dangerous projectiles in an accident or sudden stop.


I The T-type spare tire and small size


6-6 In case of emergency


I The booster battery must be rated at 12 volts. Use of an improperly rated battery can damage your vehicle.


I Whenever working on or near a bat- tery, always wear suitable eye protec- tors (for example, goggles or indus- trial safety spectacles) and remove rings, metal bands, or any other jew- elry. Do not lean over the battery when jump starting.


I Do not attempt to jump start a frozen battery. It could explode and cause serious injury.


I Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it.


SCE0392


the N (Neutral) position (On automatic transmission models, move the selector lever to the P (Park) position). Switch off all unnecessary electrical (light, heater, air conditioner, etc.).


systems


3. Remove vent caps on the battery (if so equipped). Cover the battery with an old cloth to reduce explosion hazard.


4. Connect jumper cables in the sequence as


illustrated.


WARNING


Always follow the instructions below. Failure to do so could result in damage to the charging system and cause per- sonal injury.


1. If the booster battery is in another vehicle, position the two vehicles to bring their bat- teries into close proximity to each other. Do not allow the two vehicles to touch. 2. Apply parking brake. Move the shift lever to


In case of emergency 6-7


Z 02.7.12/A33-D/V5.0 X


7. After starting your engine, carefully discon- nect the negative cable and then the posi- tive cable.


8. Replace the vent caps (if so equipped). Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid.


PUSH STARTING


Do not start the engine by pushing.


CAUTION


I Automatic transmission models can- not be push started. This may cause transmission damage.


I Three way catalyst equipped models should not be started by pushing since the three way catalyst may be damaged.


I Never try to start the vehicle by tow- ing it; when the engine starts, the forward surge could cause the ve- hicle to collide with the tow vehicle.


CAUTION


I Always connect positive (+) to posi- tive (+) and negative (−) to body ground (for example, strut mounting bolt, etc. — not to the battery).


I Make sure that cables do not touch moving parts in the engine compart- ment and that clamps do not contact any other metal.


5. Start the engine of the other vehicle and let


it run for a few minutes.


6. Keep the engine speed of the other vehicle at about 2,000 rpm, and start your engine in the normal manner.


CAUTION


Do not keep starter motor engaged for more than 10 seconds. If the engine does not start right away, turn the key off and wait 3 to 4 seconds before trying again.


6-8 In case of emergency


Z 02.7.12/A33-D/V5.0 X


contact with, or to get caught in the cooling fan, or drive belt.


I The engine cooling fan can start at any time when the coolant tempera- ture is high.


6. After the engine cools down, check the coolant level in the reservoir tank with the engine running. Add coolant to the reservoir tank if necessary. Have your vehicle re- paired at the nearest NISSAN dealer.


IF YOUR VEHICLE OVERHEATS


WARNING


I Do not continue to drive if your ve- hicle overheats. Doing so could cause a vehicle fire.


I To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radia- tor cap is removed, pressurized hot water will spurt out, possibly causing serious injury.


I Do not open the hood if steam is


coming out.


If your vehicle is overheating (indicated by an extremely high temperature gauge reading), or if you feel a lack of engine power, detect abnormal noise, etc., take the following steps:


1. Move the vehicle safely off the road, apply the parking brake and move the shift lever to the N (Neutral) position (automatic trans- mission to the P (Park) position). Do not stop the engine.


2. Turn off the air conditioner switch. Open all the windows, move the heater or air condi-


tioner temperature control to maximum hot and fan control to high speed.


3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. Wait until no steam or coolant can be seen before pro- ceeding.


4. Open the engine hood.


WARNING


If steam or water is coming from the engine, stand clear to prevent getting burned.


5. Visually check if the cooling fan is running. The radiator hoses and radiator should not leak water.


If coolant is leaking or the cooling fan does not run, stop the engine.


WARNING


I Be careful not to allow your hands, hair, jewelry or clothing to come into


In case of emergency 6-9


Z 02.7.12/A33-D/V5.0 X


TOWING YOUR VEHICLE


When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instruc- tions are available from an authorized NISSAN dealer. Local service operators are generally familiar with the applicable laws and proce- dures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service opera- tor tow your vehicle. It is advisable to have the service operator carefully read the following precautions.


WARNING


I Never ride in a vehicle that is being


towed.


I Never get under your vehicle after it


has been lifted by a tow truck.


CAUTION


I When towing, make sure that


the transmission, axles, steering system


6-10 In case of emergency


and powertrain are in working condi- tion. If any unit is damaged, dollies must be used.


I Always attach safety chains before


towing.


SCE0202


TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as illustrated.


Z 02.7.12/A33-D/V5.0 X


ground or four wheels on the ground (forward or backward) as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the rear wheels raised, always use towing dollies under the front wheels.


I When towing automatic transmission models with the front wheels on tow- ing dollies, or when towing manual transmission models with the front wheels on the ground: I Turn the ignition key to the OFF position, and secure the steering wheel in a straight ahead position with a rope or similar device. Never secure the steering wheel by turning the ignition key to the LOCK position. This may damage the steering lock mechanism.


I Move the gearshift lever to the N


(Neutral) position.


I When towing automatic or manual


transmission models with the rear wheels on the ground (if you do not use towing dollies): Always release the parking brake.


VEHICLE RECOVERY (Freeing a stuck vehicle) I Tow chains or cables must be attached only to the main structural members of the ve- hicle.


I Pulling devices should be routed so they do not touch any part of the suspension, steer- ing, brake or cooling systems.


I Always pull the cable straight out from the front or rear of the vehicle. Never pull on the vehicle at an angle.


I Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.


I Stand clear of an stuck vehicle.


In case of emergency 6-11


Z 02.7.12/A33-D/V5.0 X


SCE0199


CAUTION


I Never tow automatic transmission models with the front wheels on the


WARNING


Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be dam- aged.


6-12 In case of emergency


Z 02.7.12/A33-D/V5.0 X


7 Appearance and care


Cleaning exterior ....................................................... 7-2
Washing................................................................ 7-2
Waxing.................................................................. 7-2
Removing spots.................................................... 7-3
Underbody ............................................................ 7-3
Glass .................................................................... 7-3
Aluminum alloy wheels......................................... 7-4
Chrome parts........................................................ 7-4
Cleaning interior ........................................................ 7-4


Floor mats ............................................................ 7-4
Seat belts ............................................................. 7-5
Corrosion protection.................................................. 7-5


Most common factors contributing to vehicle corrosion............................................................... 7-5
Environmental factors influence the rate of corrosion............................................................... 7-5
To protect your vehicle from corrosion ................ 7-6


Z 02.7.12/A33-D/V5.0 X


CLEANING EXTERIOR


MAI0001


In order to maintain the appearance of your vehicle, it is important to take proper care of it.


In the following cases, please wash your ve- hicle as soon as possible to protect the paint surface. I After a rainfall to prevent possible damage


from acid rain


I After driving on coastal roads I When contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface


I When dust or mud builds up on the surface


7-2 Appearance and care


Whenever possible, store or park your vehicle inside a garage or in a covered area.


When it is necessary to park outside, park in a shady area or protect the vehicle with a body cover. Be careful not to scratch the paint surface when putting on or removing the body cover. WASHING Thoroughly rinse surface dirt off the vehicle with a wet sponge and plenty of clean water. Clean the vehicle thoroughly using a mild soap such as Nissan Car Wash, or a general pur- pose dishwashing liquid mixed with clean, lukewarm (never hot) water.


CAUTION


I Do not use strong household soap, strong chemical detergents, gasoline or solvents.


I Do not wash the vehicle in direct sunlight or while the vehicle body is hot, as the surface may become water-spotted.


I Avoid using tight-napped or rough cloths, such as washing mitts. Care must be taken when removing caked-on dirt or other foreign sub- stances so that the paint surface is not scratched or damaged.


Rinse the vehicle again with plenty of clean water.


Inside flanges, seams and folds on the doors, hatches and hood are particularly vulnerable to the effects of road salt. Therefore, these areas must be regularly cleaned. Make sure that the drain holes in the lower edge of the door are open. Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt. Avoid leaving water spots on the paint surface by using a damp chamois to dry the vehicle. WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance. After waxing, polishing is recommended to remove built-up residue and to avoid a weathered appearance. If you wish to wax your vehicle, only use a wax


Z 02.7.12/A33-D/V5.0 X


specified for use over clear coats, such as Nissan Liquid or Spray Wax. Your NISSAN dealer can assist you in choosing the proper product. I Wax your vehicle only after a thorough washing. Follow the instructions supplied with the wax.


I Do not use a wax containing any abrasives, cutting compounds or cleaners that may damage the vehicle finish.


I If the surface does not polish easily, use a


road tar remover and wax again.


Machine compounding or aggressive pol- ishing on a base coat/clear coat paint finish may dull the finish or leave swirl marks. REMOVING SPOTS Remove tar and oil spots, industrial dust, in- sects, and tree sap as quickly as possible from the surface of the paint to avoid lasting dam- age or staining. Special cleaning products are available at your NISSAN dealer or any auto- motive accessory store. UNDERBODY In areas where road salt is used in winter, the underbody must be cleaned regularly. This will prevent dirt and salt from building up and


causing underbody and suspension corrosion. Before the winter period and again in the spring, the underseal must be checked and, if necessary, re-treated.


SAI0014A


GLASS When cleaning the rear window, it may be easier to clean if the high-mounted stop light is removed first.


Be careful when removing the high-mounted stop light to reduce the risk of damaging the high-mounted stop light wires. The high-mounted stop light must be properly reinstalled before driving your vehicle. Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner Appearance and care 7-3


Z 02.7.12/A33-D/V5.0 X


FLOOR MATS The use of Genuine Nissan floor mats can extend the life of your vehicle carpet and make it easier to clean the interior. No matter what mats are used, be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation. Mats should be maintained with regular cleaning and replaced if they become excessively worn.


CLEANING INTERIOR


Occasionally remove loose dust from the inte- rior trim, plastic parts and seats using a vacuum cleaner or soft brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry soft cloth. Before using any fabric protector, read the manufacturer’s rec- ommendations. Some fabric protectors con- tain chemicals that may stain or bleach the seat material. Use a cloth dampened only with water, clean the meter and gauge lens.


to


CAUTION


I Never use gasoline, thinner, or any


similar material.


I The leather seats should be regularly coated with a leather wax like saddle soap. Never use car wax.


I Never use fabric protectors unless recommended by the manufacturer. I Do not use glass or plastic cleaner on meter or gauge lens covers. It may damage the lens cover.


and a soft cloth will easily remove this film.


CAUTION


When cleaning the inside of the window, do not use sharp-edged tools, abrasive cleaners or chlorine based disinfectant cleaners. They could damage the elec- trical conductors, radio antenna ele- ments or rear window defogger ele- ments.


ALUMINUM ALLOY WHEELS Wash regularly, especially during winter months in areas where road salt is used. Salt could discolor the wheel if not removed. CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish.


7-4 Appearance and care


Z 02.7.12/A33-D/V5.0 X


SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solu- tion. Allow the belts to dry completely before using them.


WARNING


Do not allow wet belts to roll up in the retractor. NEVER use bleach, dye, or chemical solvents since these may se- verely weaken the seat belt webbing.


CORROSION PROTECTION


MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION: I The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas.


I Damage to paint and other protective coat- ings caused by gravel and stone chips or minor traffic accidents.


ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION: Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate corro- sion. Wet floor coverings will not dry com- pletely inside the vehicle, and should be re- moved for drying to avoid floor panel corrosion. Relative humidity Corrosion will be accelerated in areas of high relative humidity, especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used.


Appearance and care 7-5


Z 02.7.12/A33-D/V5.0 X


SAI0012


Floor mat positioning aid (Driver side only) This model includes a front floor mat bracket to act as a floor mat positioning aid. NISSAN floor mats have been specially designed for your vehicle model. The driver’s side floor mat has a grommet hole incorporated in it. Simply position the mat by placing the floor mat bracket through the floor mat grommet hole while centering the mat in the floorpan contour. Periodically check to make certain that the mats are properly positioned.


Temperature A temperature increase will accelerate the rate of corrosion to those parts which are not well ventilated. Air pollution Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use will accelerate the corrosion process. Road salt will also accelerate the disintegration of paint surfaces. TO PROTECT YOUR VEHICLE FROM CORROSION: I Wash and wax your vehicle often to keep


the vehicle clean.


I Always check for minor damage to the paint


and repair it as soon as possible.


I Keep drain holes at the bottom of the doors


open to avoid water accumulation.


I Check the underbody for accumulation of sand, dirt or salt. If present, wash with water as soon as possible.


CAUTION


I NEVER remove dirt, sand or other debris from the passenger compart- ment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom.


I Never allow water or other liquids to come in contact with electronic com- ponents inside the vehicle as this may damage them.


Chemicals used for road surface de-icing are extremely corrosive. They accelerate corro- sion and deterioration of underbody compo- nents such as the exhaust system, fuel and brake lines, brake cables, floor pan and fend- ers. In winter, the underbody must be cleaned periodically. For additional protection against rust and cor- rosion, which may be required in some areas, consult your local NISSAN dealer.


7-6 Appearance and care


Z 02.7.12/A33-D/V5.0 X


8 Maintenance and do-it-yourself


Maintenance requirements........................................ 8-2
General maintenance................................................ 8-2
Explanation of general maintenance items.......... 8-2
Maintenance precautions .......................................... 8-5
Engine compartment check locations ....................... 8-7
Engine cooling system .............................................. 8-8
Checking engine coolant level ............................. 8-8
Changing engine coolant ..................................... 8-9
Engine oil ................................................................ 8-10
Checking engine oil level ................................... 8-10
Changing engine oil ........................................... 8-11
Changing engine oil filter ................................... 8-12
Automatic transmission fluid ................................... 8-12
Temperature conditions for checking................. 8-13
Power steering fluid ................................................ 8-14
Brake and clutch fluid ............................................. 8-14
Window washer fluid ............................................... 8-15
Battery ..................................................................... 8-15
Drive belts ............................................................... 8-17
Spark plugs ............................................................. 8-17
Replacing spark plugs........................................ 8-18


Air cleaner ............................................................... 8-18
Windshield wiper blades ......................................... 8-19
Cleaning ............................................................. 8-19
Replacing............................................................ 8-20
Parking brake and brake pedal............................... 8-21
Checking parking brake ..................................... 8-21
Checking brake pedal ........................................ 8-21
Brake booster ..................................................... 8-22
Fuses....................................................................... 8-22
Engine compartment .......................................... 8-22
Passenger compartment .................................... 8-24
Keyfob battery replacement .................................... 8-24
Lights....................................................................... 8-26
Headlights........................................................... 8-27
Exterior and interior lights .................................. 8-28
Wheels and tires ..................................................... 8-33
Tire pressure ...................................................... 8-33
Types of tires...................................................... 8-33
Tire chains.......................................................... 8-34
Changing wheels and tires................................. 8-35


Z 02.7.12/A33-D/V5.0 X


MAINTENANCE REQUIREMENTS


Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that scheduled maintenance, as well as gen- eral maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives the proper maintenance care. You are a vital link in the maintenance chain. Scheduled maintenance: For your convenience, both required and op- tional scheduled maintenance items are de- scribed and listed in your “Service and Main- tenance Guide”. You must refer to that guide to ensure that necessary maintenance is per- formed on your NISSAN at regular intervals. General maintenance: General maintenance includes those items which should be checked during normal day- to-day operation of the vehicle. They are es- sential if your vehicle is to continue to operate properly. It is your responsibility to perform these procedures regularly as prescribed. 8-2 Maintenance and do-it-yourself


Performing general maintenance checks re- quire minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, your NISSAN dealer. Where to go for service: If maintenance service is required or your vehicle appears to malfunction, have the sys- tems checked and tuned by an authorized NISSAN dealer. NISSAN technicians are well-trained special- ists and are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training pro- grams. They are completely qualified to work on NISSAN vehicles before they work on your vehicle, rather than after they have worked on it. You can be confident that your NISSAN deal- er’s service department performs the best job to meet the maintenance requirements of your vehicle — in a reliable and economic way.


GENERAL MAINTENANCE


During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smell, be sure to check for the cause or have your NISSAN dealer check it promptly. In addition, you should notify your NISSAN dealer if you think that repairs are required. When performing any checks or maintenance work, closely observe the “Maintenance pre- cautions” later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS Additional information on the following items with “*” is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Tires*: Check the pressure with a gauge at least once a month and always prior to long distance trips. If necessary, adjust the pres- sure in all tires, including the spare, to the pressure specified. Check carefully for dam- age, cuts or excessive wear. Wheel nuts*: When checking the tires, make sure no nuts are missing, and check for any


Z 02.7.12/A33-D/V5.0 X


loose nuts. Tighten if necessary. Tire rotation*: Tires should be rotated every 7,500 miles (12,000 km). Wheel alignment and balance: If the vehicle pulls to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment.


If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed.


For additional information regarding tires, refer to “Important Tire Safety Information” in the Warranty Information Booklet (US) or “Tire Safety Information” in the Warranty and Road- side Assistance Information booklet (Canada). Windshield: Clean the windshield on a regu- lar basis. Check the windshield at least every six months for cracks or other damage. Have a damaged windshield repaired by a qualified repair facility. Windshield wiper blades*: Check for cracks or wear if they do not wipe properly. Doors and engine hood: Check that all doors and the engine hood operate smoothly as well as the trunk lid or back hatch. Also make sure that all latches lock securely. Lubricate if nec-


essary. Make sure that the secondary latch keeps the hood from opening when the pri- mary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication fre- quently. Lights*: Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Warning lights and chimes: Make sure that all warning lights and chimes are operating properly. Windshield wiper and washer*: Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster: Check that the air comes out of the defroster outlets properly and in good quantity when operating the heater or air conditioner. Steering wheel: Check for changes in the


steering conditions, such as excessive free play, hard steering or strange noises. Seats: Check seat position controls such as seat adjusters, seatback recliner, etc. to en- sure they operate smoothly and that all latches lock securely in every position. Check that the head restraints move up and down smoothly and that the locks (if equipped) hold securely in all latched positions. Seat belts: Check that all parts of the seat belt system (for example, buckles, anchors, adjust- ers and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Accelerator pedal: Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mats away from the pedal. Clutch pedal*: Make sure the pedal operates smoothly and check that it has the proper free play. Brakes: Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster*: Check the pedal for smooth operation and make sure it has the proper distance under it when depressed fully. Check the brake booster function. Be sure to Maintenance and do-it-yourself 8-3


Z 02.7.12/A33-D/V5.0 X


important to remove these substances, other- wise rust will form on the floor pan, frame, fuel lines and around the exhaust system. At the end of winter, the underbody should be thor- oughly flushed with plain water, being careful to clean those areas where mud and dirt may accumulate. For additional information, see “Cleaning exterior” in the “7. Appearance and care” section. Fluid leaks: Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately.


keep floor mats away from the pedal. Parking brake*: Check that the lever has the proper travel and make sure that the vehicle is held securely on a fairly steep hill when only the parking brake is applied. Automatic transaxle P (Park) position mechanism: On a fairly steep hill check that the vehicle is held securely with the selector lever in the P (Park) position without applying any brakes. Under the hood and the vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). Windshield washer fluid*: Check that there is adequate fluid in the tank. Engine coolant level*: Check the coolant level when the engine is cold. Radiator and hoses: Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, dete- rioration or loose connections. Brake and clutch fluid levels*: Make sure that the brake and clutch fluid levels are be- tween the MAX and MIN lines on the reservoir. 8-4 Maintenance and do-it-yourself


Battery*: Check the fluid level in each cell. It should be between the MAX and MIN lines. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Engine drive belts*: Make sure that no belt is frayed, worn, cracked or oily. Engine oil level*: Check the level on the dipstick after parking the vehicle on a level spot and turning off the engine. Power steering fluid level* and lines: Check the level in the reservoir tank with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Automatic transaxle fluid level*: Check the level on the dipstick after putting the selector lever in P (Park) position with the engine idling. Exhaust system: Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust immediately locate the trouble and correct it. (See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas (carbon mon- oxide).) Underbody: The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very


fumes,


Z 02.7.12/A33-D/V5.0 X


MAINTENANCE PRECAUTIONS


When performing any inspection or mainte- nance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed.


WARNING


I Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the ve- hicle from moving. For a manual transmission, move the shift lever to N (Neutral) position. For an automatic transmission, move the selector lever to P (Park) position.


I Be sure the ignition key is OFF or LOCK when performing any parts re- placement or repairs.


I Your vehicle is equipped with an au- tomatic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the engine is not run- ning. To avoid injury, always discon-


nect the negative battery cable before working near the fan.


I If you must work with the engine running, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.


I It is advisable to secure or remove any loose clothing and any jewelry, such as rings, watches, etc. before working on your vehicle.


I Always wear eye protection when-


ever you work on your vehicle.


I If you must run the engine in an enclosed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.


I Never get under the vehicle while it is supported only by a jack. If it is nec- essary to work under the vehicle, support it with safety stands.


I Keep smoking materials, flame and sparks away from fuel and the bat-


tery.


I On gasoline engine models with the Multiport Fuel Injection (MFI) System, the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.


CAUTION


I Do not work under the hood while the engine is hot. Turn off the engine and wait until it cools down.


I Never connect or disconnect either the battery or any transistorized com- ponent connector while the ignition key is on.


I Never leave the engine or the auto- matic transmission related compo- nent harness connector discon- nected while the ignition key is on.


I Avoid direct contact with used engine oil and coolant. Improperly disposed


Maintenance and do-it-yourself 8-5


Z 02.7.12/A33-D/V5.0 X


engine oil, engine coolant and/or other vehicle fluids can hurt the envi- ronment. Always conform to local regulations for disposal of vehicle fluid.


This “8. Maintenance and do-it-yourself” sec- tion gives instructions regarding only those items which are relatively easy for an owner to perform. is also A genuine NISSAN Service Manual available. See “Owner’s Manual/Service Manual order information” in the “9. Technical and consurner information” section. You should be aware that incomplete or im- proper servicing may result in operating diffi- culties or excessive emissions, and could af- fect your warranty coverage. If in doubt about any servicing, have it done by your NISSAN dealer.


8-6 Maintenance and do-it-yourself


Z 02.7.12/A33-D/V5.0 X


ENGINE COMPARTMENT CHECK LOCATIONS


SDI1337
Maintenance and do-it-yourself 8-7


Z 02.7.12/A33-D/V5.0 X


WARNING


I Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. Wait until the engine and radiator cool down.


I See “If your vehicle overheats” in the


“6. In case of emergency” section.


I The radiator is equipped with a pres- sure cap. To prevent engine damage, use only a genuine NISSAN radiator cap.


ENGINE COOLING SYSTEM


The engine cooling system is filled at the factory with a high-quality, year-round, anti- freeze coolant solution. The anti-freeze solu- tion contains rust and corrosion inhibitors, therefore additional cooling system additives are not necessary.


CAUTION


When adding or replacing coolant, be sure to use only a genuine NISSAN anti- freeze coolant or equivalent with the proper mixture ratio of 50% anti-freeze and 50% demineralized water/distilled water. The use of other types of coolant solutions may damage your engine cooling system.


Outside temperature


down to


°C


−35


°F


−30


Anti- freeze


Deminer-


alized water/ distilled water


50%


50%


8-8 Maintenance and do-it-yourself


SDI0960


CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold. If the coolant level is below MIN, add coolant up to the MAX level. If the reservoir tank is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level. If the engine cooling system frequently requires coolant, have it checked by your NISSAN dealer.


Z 02.7.12/A33-D/V5.0 X


I Improper servicing can result in reduced heater performance and engine overheat- ing.


WARNING


I To avoid being scalded, never change the coolant when the engine is hot. I Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.


I Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.


I Keep coolant out of reach of children


SDI0114


CHANGING ENGINE COOLANT I Major cooling system repairs should be performed by your NISSAN dealer. The service procedures can be found in the appropriate NISSAN Service Manual.


and pets.


1. Perform the following procedure to open


the heater water cock. I Turn the ignition key from OFF to ON. I Move the heater or air conditioner tem- perature control dial to the maximum hot position then turn the ignition key to OFF.


2. Open radiator drain valve at the bottom of


radiator, and remove radiator filler cap.


I Be careful not to allow coolant to con-


tact drive belts.


I Waste coolant must be disposed of properly. Check your local regulations. 3. Close the radiator drain valve securely after


the coolant is drained.


4. Fill the radiator slowly with the proper mix- ture of anti-freeze solution and demineral- ized water/distilled water. Fill the reservoir tank up to the MAX level. Then install the radiator filler cap.


5. Start


the engine and warm it up until


it reaches normal operating temperature. Then race the engine 2 or 3 times under no load. Watch the engine coolant gauge for signs of overheating.


temperature


6. Stop the engine. After it completely cools down, refill the radiator up to the filler opening. Fill the reservoir tank up to the MAX level. Check the drain valve for any sign of leakage.


7. Recheck the coolant level after the vehicle


has been driven for a day.


Maintenance and do-it-yourself 8-9


Z 02.7.12/A33-D/V5.0 X


ENGINE OIL


CAUTION


Oil level should be checked regularly. Operating with insufficient amount of oil can damage the engine, and such dam- age is not covered by warranty.


SDI0115


SDI0534


CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and


apply parking brake. 2. Run the engine until


temperature.


it reaches operating


3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil pan.


4. Remove the dipstick and wipe it clean.


Reinsert it all the way.


8-10 Maintenance and do-it-yourself


5. Remove the dipstick again and check the oil level. It should be between the H and L marks. If the oil level is below the L mark, remove the oil filler cap and pour recom- mended oil through the opening. Do not overfill.


6. Recheck oil level with dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.


Z 02.7.12/A33-D/V5.0 X


SDI0974


CHANGING ENGINE OIL 1. Park the vehicle on a level surface and


apply the parking brake.


2. Run the engine until


temperature.


it reaches operating


3. Turn the engine off and wait more than 10


minutes.


4. Place a large drain pan under the drain


plug.


5. Remove the oil filler cap.


6. Remove the drain plug with a wrench and


completely drain the oil.


If oil filter is to be changed, remove and replace it at this time. See later in “Engine oil” for changing engine oil filter.


CAUTION


Be careful not to burn yourself, as the engine oil is hot.


I Waste oil must be disposed of properly. I Check your local regulations. 7. Clean and re-install the drain plug with a new washer. Securely tighten the drain plug with a wrench. Drain plug tightening torque:


22 to 29 ft-lb (29 to 39 N(cid:215) m)


Do not use excessive force.


8. Refill engine with recommended oil and


install the cap securely. See recommended fuel/lubricants” in the “9. Technical and consumer information” section for drain and


“Capacities


and


refill capacity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine the proper amount of oil in the engine.


9. Start the engine.


Check for leakage around the drain plug. Correct as required.


10.Turn the engine off and wait more than 10
level with the dip-


minutes. Check the oil stick. Add engine oil if necessary.


11.Dispose of waste oil properly.


WARNING


I Prolonged and repeated contact with used engine oil may cause skin can- cer.


I Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.


I Keep used engine oil out of reach of


children.


Maintenance and do-it-yourself 8-11


Z 02.7.12/A33-D/V5.0 X


CAUTION


Be careful not to burn yourself, as the engine oil may be hot.


4. Wipe the engine oil filter mounting surface


with a clean rag. Be sure to remove any old rubber gasket remaining on the mounting surface of the engine.


SDI0975


5. Coat the rubber gasket on the new filter


with clean engine oil.


CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and


apply the parking brake.


2. Turn the engine off. 3. Loosen the oil filter with an oil filter wrench. (Depending on the engine model, a special cap type wrench may be required. See your NISSAN dealer if in doubt.) Remove the oil filter by turning it by hand.


8-12 Maintenance and do-it-yourself


6. Screw in the oil filter until a slight resistance is felt, then tighten additionally more than 2/3 turn. Oil filter tightening torque:


10.85 to 15.19 ft-lb (14.7 to 20.6 N(cid:215) m)


7. Start


the engine and check for leakage


around the oil filter. Correct as required.


8. Turn the engine off and wait several min- utes. Check the oil level. Add engine oil if necessary.


AUTOMATIC TRANSMISSION FLUID


SDI1051


WARNING


I When engine is running, keep hands, jewelry and clothing away from any moving parts such as cooling fan and drive belt.


I Automatic transmission fluid is poi- sonous and should be stored care- fully in marked containers out of the reach of children.


Z 02.7.12/A33-D/V5.0 X


TEMPERATURE CONDITIONS FOR CHECKING I The fluid level should be checked using the HOT range on the dipstick after the follow- ing conditions have been met: a) the engine should be warmed up to


operating temperature.


b) the vehicle should be driven at least 5


minutes.


c) the automatic transmission fluid should be warmed to between 122 and 176°F (50 and 80°C).


I The fluid can be checked at fluid tempera- tures of 86 to 122°F (30 to 50°C) using the COLD range on the dipstick after the en- gine is warmed up and before driving. How- ever, the fluid should be re-checked using the HOT range.


1. Park the vehicle on a level surface and set


the parking brake.


2. Start the engine and then move the selector lever through each gear range. Move the selector lever to P (Park) position after you have moved it through all ranges.


CAUTION


transmission


I Do not overfill. I Use only NISSAN Matic D (Continen- tal US and Alaska) or Canada Nissan automatic fluid. DexronTMIII/MerconTM or equivalent may also be used. Outside the conti- nental US and Alaska contact a NISSAN dealer for more information regarding suitable fluids, including recommended brand(s) of DexronTM III/MerconTM automatic transmission fluid.


NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the accurate fluid level cannot be read. You should wait until the fluid has cooled down (about 30 minutes).


SDI1343


3. Check the fluid level with the engine idling. 4. Remove the dipstick and wipe it clean with


lint-free paper.


5. Reinsert the dipstick into the charging pipe


as far as it will go.


6. Remove the dipstick and note the reading. If the level is at the low side of either range, add fluid to the charging pipe.


Maintenance and do-it-yourself 8-13


Z 02.7.12/A33-D/V5.0 X


POWER STEERING FLUID


BRAKE AND CLUTCH FLUID


tem and affect the vehicle’s stopping ability.


CAUTION


Do not spill the fluid on painted sur- faces. This will damage the paint. If fluid is spilled, wash with water.


SDI1076


SDI0119


Check the fluid level in the reservoir tank. The fluid level should be checked using the HOT range at fluid temperatures of 122 to 176°F (50 to 80°C) or using the COLD range at fluid temperatures of 32 to 86°F (0 to 30°C).


Check the fluid level in the reservoir. If the fluid is below the MIN line or the brake warning light comes on, add DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be thoroughly checked by your NISSAN dealer.


CAUTION


I Do not overfill. I Use Genuine Nissan PSFII or equiva-


lent.


8-14 Maintenance and do-it-yourself


WARNING


Use only new fluid. Old, inferior, or con- taminated fluid may damage the brake and clutch systems. The use of im- proper fluids can damage the brake sys-


Z 02.7.12/A33-D/V5.0 X


WINDOW WASHER FLUID


BATTERY


WARNING


Anti-freeze is poisonous and should be stored carefully in marked containers out of the reach of children.


CAUTION


Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint.


SDI0961A


Add fluid when the low washer fluid warning light comes on. Add a washer solvent to the water for better cleaning. In the winter season, add a windshield washer anti-freeze. Follow the manufacturer’s instructions for the mixture ratio.


I Keep the battery surface clean and dry. Any corrosion should be washed off with a solution of baking soda and water.


I Make certain the terminal connections are


clean and securely tightened.


I If the vehicle is not to be used for 30 days or longer, disconnect the (—) negative battery terminal cable to prevent discharging it.


WARNING


I Do not expose the battery to flames or electrical sparks. Hydrogen gas generated by battery action is explo- sive. Do not allow battery fluid to contact your skin, eyes, fabrics, or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.


I Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the bat-


Maintenance and do-it-yourself 8-15


Z 02.7.12/A33-D/V5.0 X


JUMP STARTING If jump starting is necessary, see “Jump start- ing” in the “6. In case of emergency” section. If the engine does not start by jump starting, the battery may have to be replaced. Contact your NISSAN dealer.


tery which can generate heat, reduce battery life, and in some cases lead to an explosion.


I When working on or near a battery, always wear suitable eye protection and remove all jewelry.


I Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after han- dling.


I Keep the battery out of the reach of


children.


DI0137M


Check the fluid level in each cell. It should be between the MAX and MIN lines. If it is necessary to add fluid, add only distilled water to bring the level to the indicator in each filler opening. Do not overfill. Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. 1. Remove the cell plugs. 2. Add distilled water up to the MAX level. 3. Tighten cell plugs.


8-16 Maintenance and do-it-yourself


Z 02.7.12/A33-D/V5.0 X


DRIVE BELTS


SPARK PLUGS


2. Have the belts checked regularly for condi-


tion and tension.


WARNING


SDI0141


WARNING


Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.


1. Visually inspect each belt for signs of un- usual wear, cuts, fraying, oil adhesion or looseness. If the belt is in poor condition or loose, have it replaced or adjusted by your NISSAN dealer.


Be sure the engine and ignition switch are off and that the parking brake is engaged securely.


CAUTION


Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.


Maintenance and do-it-yourself 8-17


Z 02.7.12/A33-D/V5.0 X


AIR CLEANER


not only cleans the air, it stops flame if the engine backfires. If it is not there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed and be care- ful when working on the engine with the air cleaner removed.


I Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.


SDI0145


SDI0963


REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace the platinum- tipped spark plugs as frequently as the con- ventional type spark plugs since they will last much longer. Follow the maintenance sched- ule but, do not reuse them by cleaning or regapping. If replacement is required, see your NISSAN dealer for servicing. Always platinum-tipped spark plugs.


replace with


recommended


The filter element should not be cleaned and reused. Replace it according to the mainte- nance intervals. See the separate Service and Maintenance Guide. When replacing the filter, wipe the inside of the air cleaner housing and the cover with a damp cloth.


WARNING


I Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner


8-18 Maintenance and do-it-yourself


Z 02.7.12/A33-D/V5.0 X


gent. Then rinse the blade with clear water. If your windshield is still not clear after cleaning the blades and using the wiper, replace the blades.


WINDSHIELD WIPER BLADES


CAUTION


I After wiper blade replacement, return the wiper arm to its original position.


Otherwise it may be damaged when the engine hood is opened.


I Make sure the wiper blade contacts the glass, otherwise the arm may be damaged from wind pressure.


I Worn windshield wiper blades can damage the windshield and impair driver vision.


CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield.


Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water.


Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter-


Maintenance and do-it-yourself 8-19


Z 02.7.12/A33-D/V5.0 X


REPLACING Replace the wiper blades if they are worn. 1. Pull the wiper arm. 2. Push the lock pin, then remove the wiper


blade.


3. Insert the new wiper blade to the wiper arm


until a click sounds.


8-20 Maintenance and do-it-yourself


DI1018M


SDI0146


If you wax the surface of the hood, be careful not to let wax get into the washer nozzle. This may clog the nozzle that could cause improper windshield washer opera- tion. If wax gets into the nozzle, unclog it with a needle or small pin.


Z 02.7.12/A33-D/V5.0 X


PARKING BRAKE AND BRAKE PEDAL


SDI0125


DI1020MH


CHECKING PARKING BRAKE From the released position, pull the parking brake lever up slowly and firmly. If the number of clicks is out of the range listed above, see your NISSAN dealer.


CHECKING BRAKE PEDAL With the engine running, check the distance between the upper surface of the pedal and the metal floor. If it is out of the range shown above, see your NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The disc-type brakes self-adjust every time the brake pedal is applied.


WARNING


See your NISSAN dealer and have it checked if the brake pedal height does not return to normal.


Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires replacement, it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indi- cator sound is heard. Under some driving or climate conditions, oc- casional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For additional information, see the separate Service and Maintenance Guide.


Maintenance and do-it-yourself 8-21


Z 02.7.12/A33-D/V5.0 X


BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the times. When brake brake pedal several pedal movement (distance of travel) re- mains the same from one pedal application to the next, continue on to the next step.


2. While depressing the brake pedal, start the engine. The pedal height should drop a little.


3. With the brake pedal depressed, stop the engine. Keeping the pedal depressed for about 30 seconds, the pedal height should not change.


4. Run the engine for one minute without depressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradu- ally with each depression as the vacuum is released from the booster.


If the brakes do not operate properly, see your NISSAN dealer.


8-22 Maintenance and do-it-yourself


FUSES


CAUTION


Never use a fuse of higher amperage rating than that specified on the fuse box cover. This could damage the elec- trical system or cause a fire.


SDI0964


ENGINE COMPARTMENT If any electrical equipment does not operate, check for an open fuse.


1. Be sure the ignition key and headlight


switch are OFF.


2. Open the engine hood.


3. Remove the fusible link cover.


4. Remove the fuse with the fuse puller.


5. If the fuse is open, replace it with a new


fuse.


6. If a new fuse also opens, have the electrical


Z 02.7.12/A33-D/V5.0 X


system checked and repaired by your NISSAN dealer.


SDI0965


Fusible links If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts.


Maintenance and do-it-yourself 8-23


Z 02.7.12/A33-D/V5.0 X


KEYFOB BATTERY REPLACEMENT


SDI0966


SPA1374


Replace the battery as follows:


1. Open the lid using a suitable tool.


2. Replace the battery with a new one.


Recommended battery: Sanyo CR2025 or equivalent


Z 02.7.12/A33-D/V5.0 X


PASSENGER COMPARTMENT If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition key and the headlight


switch are OFF.


2. Pull to open the fuse box lid. 3. Remove the fuse with the fuse puller. 4. If the fuse is open, replace it with a new


fuse.


5. If a new fuse also opens, have the electrical system checked and repaired by your NISSAN dealer.


8-24 Maintenance and do-it-yourself


Industry Canada. Operation is subject to the following two conditions: (1) This de- vice may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation of the device.


Make sure that the ¯ bottom case.


3. Close the lid securely.


side faces the


4. Push the keyfob button two or three times


to check its operation.


See your NISSAN dealer if you need any assistance for replacement. If the battery is removed for any reason other than replacement, perform step 4
above. I Be careful not to touch a circuit board


and a battery terminal.


I An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal.


I The keyfob is water-resistant; however, if it does get wet, immediately wipe com- pletely dry.


I When changing batteries, do not let dust


or oil get on the keyfob.


FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of


Maintenance and do-it-yourself 8-25


Z 02.7.12/A33-D/V5.0 X


LIGHTS


8-26 Maintenance and do-it-yourself


SDI1336


Z 02.7.12/A33-D/V5.0 X


HEADLIGHTS Replacing the xenon headlight bulb — low beam


WARNING


HIGH VOLTAGE


When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at an autho- rized NISSAN dealer. For additional in- formation, see “Headlight and turn signal switch” in the “2. Instruments and controls” section.


Replacing the halogen headlight bulb — high beam The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. A bulb can be replaced from inside the engine compartment without removing the headlight assembly.


CAUTION


High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.


When handling the bulb, do not touch the glass envelope.


SDI1333


1. Disconnect the battery negative cable. 2. Turn the connector to loosen it. 3. Remove the headlight bulb. Do not shake


or rotate the bulb when removing it.


4. Install the new bulb in the reverse order of


removal.


Aiming is not necessary after replacing the bulb. When aiming adjustment is neces- sary, contact your NISSAN dealer.


Maintenance and do-it-yourself 8-27


Z 02.7.12/A33-D/V5.0 X


CAUTION


EXTERIOR AND INTERIOR LIGHTS


Item


Wattage (W)


Bulb No.


I Do not touch the bulb. I Use the same number and wattage as


Front turn signal


Clearance light


originally installed: Wattage 60
Bulb no. HB3


I Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the headlight.


8-28 Maintenance and do-it-yourself


Front side marker light


Front fog light (if so equipped)


Rear combination light


Turn signal


Stop/Tail


Back-up


Rear side marker light


License plate light


High-mounted stop light (if so equipped)


Interior light


Front personal light


Step light


Trunk light


Vanity mirror light (if so equipped)


T20


T10


T10


T20


T20


T16


T10


T20


161


158



21


3.8


See an authorized NISSAN


dealer for assistance.


21


21/5


13


3.8


21


10


10


2.7


3.4


1.4


Z 02.7.12/A33-D/V5.0 X


MDI0006


Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.


SDI1334


SDI0969
Maintenance and do-it-yourself 8-29


Z 02.7.12/A33-D/V5.0 X


8-30 Maintenance and do-it-yourself


SDI0970


Z 02.7.12/A33-D/V5.0 X


SDI1335
Maintenance and do-it-yourself 8-31


Z 02.7.12/A33-D/V5.0 X


SDI0333A


8-32 Maintenance and do-it-yourself


SDI1340


SDI0756


Z 02.7.12/A33-D/V5.0 X


WHEELS AND TIRES


DI1033M


If you have a flat tire, see “Flat tire” in the “6. In case of emergency” section. TIRE PRESSURE Maximum inflation pressure Do not exceed the maximum inflation pres- sures shown on the side wall of the tire. Tire inflation pressure Check the tire pressure (including spare) at least once a month and always prior to long distance trips. Incorrect tire pressure may ad- versely affect tire life and vehicle handling. Tire pressure should be checked when tires are COLD. Tires are considered COLD after the


vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. COLD tire pressures are shown on the tire placard affixed to the console box lid.


WARNING


I Improperly inflated tires can fail sud-


denly and cause an accident.


I The vehicle capacity weight is indi- cated on the tire placard. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire fail- ure, or unfavorable handling charac- teristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components. I Before taking a long trip, or whenever you have loaded your vehicle heavily, use a tire pressure gauge to ensure that the tire pressure is at the speci- fied level.


I Do not drive your vehicle over 85


MPH (140 km/h) unless it is equipped with high speed capability tires. Driv- ing faster than 85 MPH (140 km/h) may result in tire failure, loss of con- trol and possible injury.


I For additional information regarding tires, refer to “Important Tire Safety Information” in the Warranty Informa- tion Booklet (US) or “Tire Safety In- formation” in the Warranty Informa- tion booklet (Canada).


TYPES OF TIRES


CAUTION


I When changing or replacing tires, be sure all four tires are of the same type (i.e., summer, all season or snow) and construction. Your NISSAN dealer may be able to help you with informa- tion about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may


Maintenance and do-it-yourself 8-33


Z 02.7.12/A33-D/V5.0 X


ing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class S chains. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manu- facturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action dam- age to the fenders or undercarriage. If pos- sible, avoid fully loading your vehicle when using tire chains. In addition, drive at a re- duced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and perfor- mance may be adversely affected. Never install tire chains on a T-type spare tire. Do not use the chains on dry roads.


not match the potential maximum ve- hicle speed. Never exceed the maxi- mum speed rating of the tire.


I For additional information regarding tires, refer to “Important Tire Safety Information” in the Warranty Informa- tion Booklet (US) or “Tire Safety In- formation” in the Warranty Informa- tion booklet (Canada).


Loading...
x