2001 Nissan Frontier Owners Manual

WARNING

c The pre-tensioner seat belt cannot be reused after activation. It must be replaced together with the retractor and buckle as a unit.

collision

c If the vehicle becomes involved in a frontal pre- tensioner is not activated, be sure to have system checked and, if necessary, replaced by your NISSAN dealer.

pre-tensioner

but

the

the

c No unauthorized changes should be made to any components or wiring of the pre-tensioner seat belt sys- tem. This is to prevent accidental activation of the pre-tensioner seat- belt or damage to the pre-tensioner seat belt operation. Tampering with the pre-tensioner seat belt system

The pre-tensioner is encased with the seat belt’s retractor. These seat belts are used the same as conventional seat belts. When the pre-tensioner seat belt activates, smoke is released and a loud noise may be heard. The smoke is not harmful, but care should be taken not to intentionally inhale it as it may cause irritation and choking. If any abnormality occurs in the pre- tensioner system, the supplemental air bag warning light will flash intermittently after the ignition key is turned to the ON or START position. the pre- tensioner seat belt will not function properly. When selling your vehicle, we request that you inform the buyer about the pre- tensioner seat belt system and guide the buyer to the appropriate sections in this Owner’s Manual.

In this case,

may result in serious personal in- jury.

c Work around and on the pre- tensioner system should be done by an authorized NISSAN dealer. Instal- lation of electrical equipment should also be done by an authorized NIS- SAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pre- tensioner seat belt system.

c If you need to dispose of the pre- tensioner or scrap the vehicle, con- tact an authorized NISSAN dealer. Correct pre-tensioner disposal pro- cedures are set forth in the appropri- ate NISSAN Service Manual. Incor- rect disposal procedures could cause personal injury.

The front seat pre-tensioner seat belt sys- tem activates in conjunction with the supple- mental air bag. Working with the seat belt retractor, it helps tighten the seat belt the instant the vehicle becomes involved in certain types of collisions.

1-16 Seats, restraints and supplemental air bag systems

Z X

PASSENGER SUPPLEMENTAL AIR BAG ON/OFF SWITCH AND LIGHT (except Crew Cab models)

WARNING

Air bags and seat belts are designed to work as a unit. Do not switch the air bag OFF unless you meet federal govern- ment criteria. Switching off the air bag may increase the risk of serious or fatal injuries in a collision where the air bag would have inflated.

In rare instances, some passengers are exposed to serious injury risks from inflating air bags, especially if not properly re- strained. The U.S. and Canadian federal governments recognize other limited circum- stances in which an air bag could reduce safety. The passenger air bag ON/OFF switch is, therefore, allowed in models with- out full rear seats. Because the overall ben- efits of air bags are great, in most situations air bags should not be switched off unless special government criteria exist. The passenger air bag ON/OFF switch is located in the center of the instrument panel, near the ashtray. It can be used to Seats, restraints and supplemental air bag systems 1-17

WRS0060

Z X

turn the passenger supplemental air bag OFF. The ON/OFF switch should ONLY be used to turn the passenger supplemental air bag OFF when the following government criteria exists:

c Infants (less than 1 year old) in rear facing child restraints MUST be placed in the front passenger seat.

c Children ages 1-12 years MUST be

placed in the front passenger seat.

c The passenger has a medical condition which, according to a physician, causes the air bag to pose a special risk and makes the potential harm from the air- bag greater than the potential harm from turning off the air bag.

Seat belts and child restraints should al- ways be properly used. See “Precautions on seat belt usage” and “Child restraints” later in this section for details. To turn the passenger supplemental air bag OFF, insert the ignition key in the passenger supplemental air bag ON/OFF switch and turn the switch clockwise to the OFF position. Then remove the key. When the ignition is turned to the ON or START position the 1-18 Seats, restraints and supplemental air bag systems

passenger air bag OFF indicator light will illuminate to indicate the air bag is OFF. To turn the passenger supplemental air bag ON, insert the ignition key in the passenger supplemental air bag ON/OFF switch and turn the switch counter clockwise to the ON position. Then remove the key. When the ignition is turned to the ON or START posi- tion the passenger air bag OFF indicator light will illuminate for 7 seconds to indicate the system is working properly and then go out to indicate that the passenger supplemental air bag is ON. When the switch is turned to the ON posi- tion, the passenger supplemental air bag is enabled and could inflate in a frontal colli- sion. When the switch is turned to the OFF the passenger supplemental air position, bag is disabled and will not inflate in a frontal collision. The passenger supplemen- tal air bag OFF indicator light on the instru- ment panel illuminates when the passenger supplemental air bag ON/OFF switch is turned to the OFF position. The driver’s side supplemental air bag always remains en- abled and is not affected by the passenger supplemental air bag ON/OFF switch. The passenger supplemental air bag light,

displaying OFF in the center of the instru- ment panel, monitors the position of the passenger supplemental air bag ON/OFF switch. When the ignition key is in the ON or START position, illuminates for about 7 seconds and then turns off if the air bag is ON/OFF switch is in the ON position, or stays on if the passenger supplemental air bag ON/OFF switch is in the OFF posi- tion.

the light

WARNING

c Do not switch the air bag OFF unless you meet the federal government cri- teria outlined previously. This ve- hicle (except Crew Cab models) is equipped with seat belts with a (load limiter( feature. The seat belts are designed to work with the air bags to reduce the risk of injury in a colli- sion. The seat belts are designed to release additional belt webbing dur- ing some collisions to reduce the concentration of force on the occu- pant’s chest area. In a collision with the airbag turned OFF, the seat belt may allow the occupant enough for- ward movement to incur serious or fatal injuries.

Z X

c If the supplemental air bag warning light located in the instrument panel next to the speedometer comes on when the passenger supplemental air bag OFF light is also illuminated, something may be wrong with the air bag system. Infants, children ages 1-12 or persons with special medical conditions should not use the front passenger seat until the system is checked by your NISSAN dealer.

c Keep the passenger supplemental air bag ON/OFF switch turned ON unless a rear-facing child restraint must be used in the front seat, if children ages 1-12 must be placed in the front seat, or if the passenger has a medical condition, which, ac- cording to a physician, causes the air bag to pose a special risk of harm (the federal government criteria). If the switch is OFF, the air bag will not inflate in a collision as designed and the extra protection provided by the air bag may be lost.

c Be sure to turn the passenger supplemental air bag ON/OFF switch OFF when using a rear facing child restraint in the front passenger seat. If it is not OFF, the air bag may inflate in a collision. The force of the rapidly inflating air bag could cause serious injury or kill the child in the child restraint. Children ages 1-12 and persons with special medical condi- tions may also be at risk from an inflating air bag.

Seats, restraints and supplemental air bag systems 1-19

Z X

SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental air bag system are placed in the vehicle as shown in the illustration.

1-20 Seats, restraints and supplemental air bag systems

WRS0061

WRS0062

SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light, displaying in the instrument panel, monitors the circuits of the supplemental air bag and pre-tensioner seat belt systems. The circuits monitored by the supplemental air bag warning light are the diagnosis sen- sor unit, the supplemental air bag modules, pre-tensioner seat belts and all related wir- ing. When the ignition key is in the ON or START position, the supplemental air bag warning

Z X

light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following system conditions occur, the supplemental air bag and pre- tensioner seat belt systems need servicing and should be taken to an authorized NISSAN dealer: c The supplemental air bag warning light remains on after approximately 7 sec- onds.

c The supplemental air bag warning light

flashes intermittently.

c The supplemental air bag warning light

does not come on at all.

Under these conditions, the Supplemental Restraint System (supplemental air bag or pre-tensioner seat belt systems) may not function properly. It must be checked and repaired.

WARNING

is on,

it could mean that

If the supplemental air bag warning light the supplemental air bag or pre-tensioner seat belt systems will not operate in an accident.

Repair and replacement procedure The supplemental air bag modules are de- signed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred. Repair and replacement of the supplemen- tal air bag system should be done only by an authorized NISSAN dealer. To ensure long-term functioning, the supplemental air bag system must be inspected 10 years after the date of manufacture noted on the certification label located on the driver side door jamb pillar. When maintenance work is required on the vehicle, the supplemental air bag system and related parts should be pointed out to the person conducting the maintenance.

The ignition key must always be in the LOCK position when working under the hood or inside the vehicle.

WARNING

c Once the supplemental air bag in- flates, the supplemental air bag module will not function again and should be replaced by an authorized NISSAN dealer. The supplemental air bag module cannot be repaired.

c The supplemental air bag system should be inspected by an autho- rized NISSAN dealer if there is any damage to the front end portion of the vehicle, or replaced if the supple- mental air bag has inflated.

an

c If you need to dispose of the supple- mental air bag or scrap the vehicle, contact authorized NISSAN dealer. Correct supplemental air bag disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal proce- dures could cause personal injury.

Seats, restraints and supplemental air bag systems 1-21

Z X

SEAT BELTS

ARS1154

ARS1100

WARNING

PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured in an acci- dent and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Most U.S. States and Canadian prov- inces or territories specify that seat belts be worn at all times when a vehicle is being driven. 1-22 Seats, restraints and supplemental air bag systems

c Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be prop- erly restrained and, if appropriate, in child restraints.

c The seat belt should be properly ad- justed to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an acci- dent. Serious injury or death can occur if the seat belt is not worn properly.

c Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoul- der.

c Position the lap belt as low and snug as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of inter- nal injuries in an accident.

Z X

ARS1103

c Be sure the seat belt tongue is se- curely fastened to the proper buckle. c Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness.

c Do not allow more than one person

to use the same seat belt.

c Never carry more people in the ve-

hicle than there are seat belts.

c Never allow anyone to ride in the cargo area or in a slide-in camper or other type cargo area cover while the vehicle is in motion. These areas do not con- tain seat belts. It is not designed for passengers. They could be injured in sudden braking or a collision.

c If the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened, it may indi- cate a malfunction in the system. Have the system checked by an au- thorized NISSAN dealer.

c All seat belt assemblies including retractors and attaching hardware should be inspected by an autho- rized NISSAN dealer after any colli- sion. NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col- lision was minor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use during a collision should also be inspected and replaced if either dam- age or improper operation is noted.

CHILD SAFETY Children need adults to help protect them. They need to be properly restrained. The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for chil- dren who outgrow rear facing child re- straints.

WARNING

c Be sure to turn the passenger supplemental air bag ON/OFF switch OFF when using a rear facing child restraint in the front passenger seat in models so equipped. If it is not OFF, the air bag may inflate in a collision. The force of the rapidly inflating air bag could cause serious injury or kill the child in the child restraint. See (Passenger supple- mental air bag ON/OFF switch and light( earlier in this section.

c In crew cab models, never install a rear facing child restraint in the front passenger seat. An inflating

Seats, restraints and supplemental air bag systems 1-23

Z X

supplemental air bag could seri- ously injure or kill your child. A rear facing child restraint must only be used in the rear seat.

c Do not install a child restraint in the jump seats (King Cab model). These seats are not suitable for child re- straint installation.

c Do not install a child restraint in the center position of the front bench- seat if the type of restraint used interferes with operation of the driv- ing controls.

c Infants and children need special protection. The vehicle’s seat belts may not fit them properly. The shoul- der belt may come too close to the- face or neck. The lap belt may not fitover their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal in- jury. Always use appropriate child restraints.

All U.S. states and Canadian provinces or territories require the use of approved child restraints for infants and small children. See

later in this section for

‘‘Child restraints’’ more information. In addition, there are many types of child restraints available for larger children which should be used for maximum protection. NISSAN recommends that all pre-teen children be restrained in the rear seat if possible. According to accident statis- tics, children are safer when properly restrained in the rear seat than in the front seat. This is especially important because your vehicle has a supplemental re- straint system (Supplemental air bag system) for the front passenger (For pre- cautions, see ‘‘Supplemental restraint system’’ earlier in this section). Also, see ‘‘Passenger air bag ON/OFF switch and light’’ earlier in this section. Infants and small children NISSAN recommends that infants and small children be seated in child restraints that comply with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. You should choose a child restraint which fits your vehicle and always follow the manufacturer’s instruc- tions for installation and use.

Larger children Children who are too large for child re- straints should be seated and restrained by the seat belts which are provided. If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially avail- able) may help overcome this. The booster seat should raise the child so the shoulder belt is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Mo- tor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.

WARNING

Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is mov- ing. The child could be seriously in- jured or killed in an accident or sudden stop.

1-24 Seats, restraints and supplemental air bag systems

Z X

PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug, and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific rec- ommendations. INJURED PERSONS NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recom- mendations.

you could be thrown into it and re- ceive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. c For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat and adjust the seat belt properly.

Fastening the seat belts 1. Adjust the seat. 2. Slowly pull the seat belt out of the retrac- tor and insert the tongue into the buckle until you hear and feel the latch engage. The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and allows you some freedom of movement in the seat.

ARS1104

THREE-POINT TYPE SEAT BELT WITH RETRACTOR

WARNING

c Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be prop- erly restrained and, if appropriate, in a child restraint.

c Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident

Seats, restraints and supplemental air bag systems 1-25

Z X

See ‘‘Child restraints ’’ later in this section for more information. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passen- ger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension.

ARS1189

3. Position the lap belt portion low on the

hips as shown.

4. Pull the shoulder belt portion toward the

retractor to take up extra slack.

The front passenger seat belt has a cinch- ing mechanism for child restraint installa- tion. It is referred to as the automatic locking mode. When the cinching mechanism is activated the seat belt cannot be extracted again until the seat belt tongue is detached from the buckle and the seat belt is fully retracted.

1-26 Seats, restraints and supplemental air bag systems

ARS1054

Unfastening the seat belt To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts. Checking seat belt operation Seat belt retractors are designed to lock seat belt movement by two separate meth- ods: 1) When the seat belt is pulled quickly from

the retractor.

2) When the vehicle slows down rapidly. To increase your confidence in the seat

Z X

belts, check the operation as follows. c Grasp the shoulder belt and pull quickly forward. The retractor should lock and restrict further belt movement. the retractor does not

lock during this If check, or if you have any questions about seat belt operation, see an authorized NISSAN dealer.

WRS0083

WRS0084

Shoulder belt height adjustment (For front seats) The shoulder belt anchor height should be adjusted to the position best for you. (See ‘‘Precautions on seat belt usage’’ earlier in this section.) To adjust, pull out or squeeze the adjustment button and move the shoul- der belt anchor to the desired position, so the belt passes over the center of the shoul- der. The belt should be away from your face and neck, but not falling off of your shoulder. Release the adjustment button to lock the shoulder belt anchor into position.

Seats, restraints and supplemental air bag systems 1-27

Z X

WARNING

c After adjustment, release the adjust- ment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position.

c The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the en- tire restraint system and increase the chance or severity of injury in an accident.

c Do not sit on the armrest. The arm- rest is not a seating surface. Using the armrest as a seating surface may cause serious injury in an accident.

On 60/40 bench seat equipped models, the center seat belt buckle and tongue are identified by the word CENTER. The center seat belt tongue can only be fastened into the center seat belt buckle. Pull down and latch the armrest/storage compartment lid and push up the arm rest assembly to the upright position.

WRS0064

TWO-POINT TYPE SEAT BELT WITHOUT RETRACTOR (Center of 60/40 bench seat)

WARNING

c Do not install a child restraint in the center position of the front seat if the type of restraint used interferes with operation of the driving controls.

1-28 Seats, restraints and supplemental air bag systems

Z X

c Do not install a child restraint in the center position of the front bench seat if the type of restraint used interferes with operation of the driv- ing controls.

c Serious or fatal injury could occur.

Selecting the correct set of seat belts The center seat belt buckle and tongue are identified by the word CENTER. The center seat belt tongue can only be fastened into the center seat belt buckle.

ARS1055

Fastening the seat belts 1. Insert the tongue into the buckle until you

hear and feel the latch engage.

WRS0065

TWO-POINT TYPE SEAT BELT WITHOUT RETRACTOR (Jump seat and center of bench seat)

WARNING

c Do not install a child restraint in the jump seats (King Cab model). These seats are not suitable for child re- straint installation.

Seats, restraints and supplemental air bag systems 1-29

Z X

ARS1238

ARS1076

ARS1057

2. Tighten the belt by pulling the free end of

the belt away from the tongue.

3. Position the lap belt low on the hips as

illustrated.

4. Loosen the belt by holding the tongue at a right angle to the belt, then pull on the belt.

1-30 Seats, restraints and supplemental air bag systems

Z X

is not possible to properly fit

SEAT BELT EXTENDERS If, because of body size or driving position, it the lap- shoulder belt and fasten it, an extender is available which is compatible with the in- stalled seat belts. The extender adds ap- proximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position. See an autho- rized NISSAN dealer for assistance if the extender is required.

ARS1058

WARNING

Unfastening the seat belt To unfasten the belt, press the button on the buckle.

c Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts.

c Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.

SEAT BELT MAINTENANCE c To clean the seat belt webbings, apply a mild soap solution or any solution recommended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry.

c If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoul- der belt guide with a clean, dry cloth.

c Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt assembly should be re- placed.

Seats, restraints and supplemental air bag systems 1-31

Z X

CHILD RESTRAINTS

ARS1098

PRECAUTIONS ON CHILD RESTRAINTS

WARNING

c Infants and small children should always be placed in an appropriate child restraint while riding in the ve- hicle. Failure to use a child restraint can result in serious injury or death. c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult

to resist the forces of a severe acci- dent. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.

c In Crew Cab models, never install a rear facing child restraint in the front passenger seat. An inflating supple- mental air bag could seriously injure or kill your child. A rear facing child restraint must only be used in the rear seat.

c Never install a rear-facing child re- straint in the front seat of a model equipped with a supplemental air bag ON/OFF switch unless you first turn OFF the air bag. An inflating air bag could seriously injure or kill your child. See ‘‘Passenger supple- mental air bag ON/OFF switch and light’’ earlier in this section.

c An improperly installed child re- straint could lead to serious injury or death in an accident.

c In general, child restraints are de- signed to be installed with a lap belt or the lap portion of a three-point type seat belt.

c Nissan recommends that the child restraint be installed in the rear seat. According to accident statistics, children are safer when properly re- strained in the rear seat than in the- front seat.

Child restraints for infants and small chil- dren of various sizes are offered by several manufacturers. When selecting any child restraint, keep the following points in mind: 1) Choose only a restraint with a label cer- tifying that it complies with Federal Motor Vehicle Safety Standard 213 or Cana- dian Motor Vehicle Safety Standard 213. 2) Check the child restraint in your vehicle to be sure it is compatible with the vehi- cle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recommended practice J1819 for child restraint installation.

3) If the child restraint is compatible with your vehicle, place your child in the child

1-32 Seats, restraints and supplemental air bag systems

Z X

restraint and check the various adjust- ments to be sure the child restraint is compatible with your child. Always follow all of the recommended procedures.

All U.S. states and provinces of Canada require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated.

WARNING

c Do not install a child restraint in the jump seats (King Cab model). These seats are not suitable for child re- straint installation.

c Do not install a child restraint in the center position of the front bench seat if the type of restraint used interferes with operation of the driv- ing controls.

c Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.

c Follow all of

the child restraint manufacturer’s instructions for in- stallation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.

c If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.

c Adjustable seatbacks should be po- sitioned to fit the child restraint, but as upright as possible.

c After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary or put the restraint in another seat and test it again.

c For a front facing child restraint, if the seat position where it is installed has a 3-point type lap/shoulder belt, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoul- der belt behind the child restraint. If you must install a front-facing child restraint in the front seat, see (Instal- lation on front passenger seat( later in this section for details.

c When your child restraint is not in use, keep it secured with a seat belt to prevent from being thrown around in case of a sudden stop or accident.

it

CAUTION

Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.

Seats, restraints and supplemental air bag systems 1-33

Z X

ARS1247

ARS1169

ARS1170

INSTALLATION ON REAR BENCH SEAT CENTER POSI- TION (Crew Cab models only) Front facing When you install a child restraint in the rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. Always follow the restraint manufacturer’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.

1-34 Seats, restraints and supplemental air bag systems

Z X

ARS1171

ARS1248

ARS1173

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely in place.

5. If it is not secure, try to tighten the belt again, or put the restraint in another seat. 6. Check to make sure the child restraint is

properly secured prior to each use.

Rear facing When you install a child restraint in the rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. Always follow the restraint manufacturer’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

Seats, restraints and supplemental air bag systems 1-35

Z X

ARS1174

ARS1175

3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.

4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely in place.

5. If it is not secure, try to tighten the belt again, or put the restraint in another seat. 6. Check to make sure the child restraint is

properly secured prior to each use.

1-36 Seats, restraints and supplemental air bag systems

INSTALLATION ON REAR BENCH SEAT OUTBOARD POSI- TIONS (Crew Cab models only) Front facing

WARNING

c The three-point belt in your vehicle is equipped with an automatic lock- ing mode retractor which must be used when installing a child re- straint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

Z X

ARS1176

ARS1177

ARS1178

When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. Always follow the restraint manufactur- er’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the belt is fully retracted.

Seats, restraints and supplemental air bag systems 1-37

Z X

ARS1179

ARS1180

4. Allow the belt to retract. Pull up on the shoulder belt to remove any slack in the belt. If necessary to ensure the child re- straint is secure, pull the shoulder belt through the seat belt tongue beyond the stitching in the belt. After the seat belt is fully retracted and the child restraint is removed from the seat, the stitching on the shoulder belt can be pulled back through the seat belt tongue. The stitching locates the seat belt tongue near the top of the seat back for easy access for rear seat passengers.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retrac- tor, the retractor is in the automatic lock- ing mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.

1-38 Seats, restraints and supplemental air bag systems

After the child restraint is removed and the seat belt is fully retracted the automatic locking mode (child restraint mode) is can- celed. Rear facing

WARNING

c The three-point belt in your vehicle is equipped with an automatic lock- ing mode retractor which must be used when installing a child re- straint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The seat could tip over or otherwise be unse- cured and cause injury to the child in a sudden stop or collision.

Z X

ARS1181

ARS1182

ARS1183

When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. Always follow the restraint manufactur- er’s instructions.

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel it engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the belt is fully retracted.

Seats, restraints and supplemental air bag systems 1-39

Z X

After the child restraint is removed and the seat belt is fully retracted the automatic locking mode (child restraint mode) is can- celed.

ARS1184

ARS1185

4. Allow the belt to retract. Pull up on the shoulder belt to remove any slack in the belt. If necessary to ensure the child re- straint is secure, pull the shoulder belt through the seat belt tongue beyond the stitching in the belt. After the seat belt is fully retracted and the child restraint is removed from the seat, the stitching on the shoulder belt can be pulled back through the seat belt tongue. This stitching locates the seat belt tongue near the top of the seat back for easy access for rear seat passengers.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retrac- tor, the retractor is in the automatic lock- ing mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.

1-40 Seats, restraints and supplemental air bag systems

Z X

WRS0074

TOP TETHER STRAP CHILD RESTRAINT If your child restraint has a top tether strap, it must be secured to the provided anchor point. Secure the child restraint with a seat belt. Secure the top tether strap to the anchor bracket. Tighten the strap according to manufacturer instructions to remove any slack.

WARNING

c Do not install a child restraint in the center position of the front bench seat if the type of restraint used interferes with operation of the driv- ing controls.

c Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances is it to be used for adult seat belts or harnesses.

ARS1244

Anchor point locations Anchor points are located under the rear window. The back panel carpet has flaps to allow access to the anchor points and are marked with the label shown. Regular and King Cab vehicles equipped with bench seats will have both the center and outer anchor points. Regular and King Cab ve- hicles with bucket seats will only have the outer anchor point. Crew Cab vehicles will have all three anchor points. If you have any questions when install- ing a top strap child restraint, consult your NISSAN dealer for details.

Seats, restraints and supplemental air bag systems 1-41

Z X

ARS1245

WRS0094

ARS1109

1-42 Seats, restraints and supplemental air bag systems

INSTALLATION ON FRONT PASSENGER SEAT Front facing (Three-point type with retractor)

WARNING

c If so equipped, keep the passenger supplemental air bag ON/OFF switch turned ON unless a rear-facing child restraint is used in the front seat. If the switch is OFF, the air bag will not inflate in a collision as designed.

Z X

if you must

c NISSAN recommends that child re- straints be installed in the rear seat. However, install a forward-facing child restrain in the front passenger seat, move the pas- senger seat to the rear most posi- tion.

c Never install a rear facing child re- straint in the front seating position of crew cab models. Install a rear facing child restraint in the rear seat only. The force of the inflating air bag could cause serious injury or kill the child in the child restraint.

c The three-point belt in your vehicle is equipped with a locking mode re- tractor which must be used when installing a child restraint.

c Failure to use the retractor’s locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision. c If the supplemental air bag warning light located in the instrument panel

next to the speedometer comes on- when the passenger supplemental air bag OFF indicator light is also illumi- nated, something may be wrong with the supplemental air bag system. Do not use a child restraint in the front passenger seat until the system is checked by your NISSAN dealer.

ARS1093

If you choose to install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. Move the seat to the rearmost position. Always follow the re- straint manufacturer’s instructions.

Seats, restraints and supplemental air bag systems 1-43

Z X

ARS1073

ARS1034

ARS1074

2. Route the seat belt tongue through the child restraint and insert the belt tongue into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the belt is fully retracted.

4. Allow the belt to retract. Pull up on the

belt to remove any slack in the belt.

1-44 Seats, restraints and supplemental air bag systems

Z X

ARS1111

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securely held in place.

6. Check that the retractor is in the auto- matic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retrac- tor, the retractor is in the automatic lock- ing mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps three through six.

After the child restraint is removed and the seat belt is fully retracted, the automatic locking mode (child restraint mode) is can- celed. Rear facing (Three-point type with retractor, except Crew Cab models)

WARNING

c Never install a rear facing child re- straint in the front seating position of crew cab models. Install a rear facing child restraint in the rear seat only. The force of the inflating air bag could cause serious injury or kill the child in the child restraint.

c If so equipped, keep the passenger supplemental air bag ON/OFF switch turned ON unless a rear-facing child restraint is used in the front seat. If the switch is OFF, the air bag will not inflate in a collision as designed.

c Be sure to turn the passenger supplemental air bag ON/OFF switch OFF when using a rear facing child restraint in the front passenger seat. If it is not OFF, the air bag may inflate in a collision. The force of the rapidly inflating air bag could cause serious injury or kill the child in the child restraint. See ‘‘Passenger supple- mental air bag ON/OFF switch and light’’ earlier in this section.

c If the supplemental air bag warning light located in the instrument panel next to the speedometer comes on when the passenger supplemental air bag OFF indicator light is also illumi- nated, something may be wrong with the air bag system. Do not use a child restraint in the front passenger seat until the system is checked by your NISSAN dealer.

c The passenger three-point seat belt is equipped with an automatic lock- ing mode retractor which must be used when installing a child re- straint.

Seats, restraints and supplemental air bag systems 1-45

Z X

c Failure to use the automatic locking mode will result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.

ARS1105

ARS1106

If you choose to install a child restraint, follow these steps: 1. Position the child restraint on the front passenger seat. Always follow the re- straint manufacturer’s instructions.

2. Route the seat belt tongue through the child restraint and insert the belt tongue into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.

1-46 Seats, restraints and supplemental air bag systems

Z X

ARS1092

ARS1107

ARS1108

3. Pull on the shoulder belt until all of the belt is fully extended. At this time, the belt retractor is in the automatic locking mode (child restraint mode). It reverts back to emergency locking mode when the belt is fully retracted.

4. Allow the belt to retract. Pull up on the

belt to remove any slack in the belt.

5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure it is securly held in place.

6. Ensure the retractor is in the automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the automatic locking mode.

7. Check to make sure the child restraint is properly secured prior to each use. If the lap belt is not locked, repeat steps three through six.

Seats, restraints and supplemental air bag systems 1-47

Z X

After the child restraint is removed and the seat belt is fully retracted the automatic locking mode (child restraint mode) is can- celed.

1-48 Seats, restraints and supplemental air bag systems

Z X

2 Instruments and controls

Meters and gauges ................................................2-2
Speedometer and odometer .............................2-3
............................................2-3
Tachometer........................................................2-5
Engine coolant temperature gauge...................2-5
Fuel gauge ........................................................2-6
Warning/indicator lights and chimes ......................2-7
Checking bulbs..................................................2-7
Warning lights....................................................2-8
Indicator lights .................................................2-10
Chimes.............................................................2-12
Security system ..................................................2-12
Vehicle security system (if so equipped) ........2-12
Windshield wiper and washer switch...................2-15
Switch operation..............................................2-16

Rear window defogger switch (Crew Cab models only).........................................................2-16
Headlight and turn signal switch..........................2-17
Headlight switch ..............................................2-17
Turn signal switch............................................2-18
Front fog light switch (if so equipped)..................2-18
Hazard warning flasher switch.............................2-19

Horn......................................................................2-19
Power point (if so equipped)................................2-20
Cigarette lighter (accessory) and ash tray...........2-20
Storage.................................................................2-21

Storage compartment (Crew Cab models only) ....................................................2-21
Cup holders (if so equipped)...........................2-21
Glove box ........................................................2-22
Grocery hooks (King Cab only).......................2-23
Windows...............................................................2-23
Power windows (if so equipped) .....................2-23
Manual windows..............................................2-25
Rear sliding window (if so equipped)..............2-25
Sunroof (if so equipped).......................................2-25
Tilting the sunroof............................................2-25
Removing/installing..........................................2-26
Interior lights.........................................................2-28
Map lights (if so equipped)...................................2-29
Illuminated entry system ......................................2-29
Battery saver ...................................................2-29

Z X

Z X

METERS AND GAUGES

2-2 Instruments and controls

WIC0055

Z X

SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). Odometer/Twin trip odometer The odometer records the total distance the vehicle has been driven.

WIC0056

Instruments and controls 2-3

Z X

The trip odometer records the distance of individual trips. Before each trip reset the trip odometer.

Push the reset knob to change the display as follows: ODO (odometer)!TRIP A!TRIP B!ODO. Push and hold the reset knob for more than 1 second to reset either trip odometer.

2-4 Instruments and controls

AIC1120

Z X

WIC0057

WIC0058

TACHOMETER The tachometer indicates engine speed in revolutions per minute (r/min).

CAUTION

When engine speed approaches the red zone, shift to a higher gear. Oper- ating the engine in the red zone may cause serious engine damage.

ENGINE COOLANT TEMPERA- TURE GAUGE The gauge indicates the engine coolant temperature. The engine coolant temperature varies with the outside air temperature and driving con- ditions.

CAUTION

If the gauge indicates engine coolant temperature over the normal range, stop the vehicle as soon as safely pos- sible. If the engine is overheated, con- tinued operation of the vehicle may seriously damage the engine. See the ‘‘In case of emergency’’ section for immediate action required.

Instruments and controls 2-5

Z X

CAUTION

malfunction indicator

c If the vehicle runs out of fuel, the lamp (MIL) may come on. Refuel as soon as possible. After a few driving trips, the lamp should turn off. If the lamp remains on after a few driving trips, have the vehicle inspected by an authorized NISSAN dealer.

c For additional information, see the (Malfunction indicator lamp (MIL)( later in this section.

WIC0059

FUEL GAUGE The gauge indicates the APPROXIMATE fuel level in the tank. The gauge may move slightly during brak- ing, turning, acceleration, or going up or down hills. The gauge needle returns to empty (E) after the ignition key is turned OFF. Refill the fuel tank before the gauge registers E (Empty).

2-6 Instruments and controls

Z X

WARNING/INDICATOR LIGHTS AND CHIMES

Turn signal/hazard indicator lights

or

Brake warning light

High beam indicator light

Seat belt reminder light and chime

Engine oil pressure warning light

Low washer fluid warning light (Canada only)

4-wheel drive indicator light

model)

CRUISE main switch indicator light (if so equipped)

Cruise SET indicator light (if so equipped)

Overdrive off indicator light (automatic transmission only)

Charge warning light

Malfunction indicator lamp (MIL)

Low fuel warning light

or

Anti-lock brake warning light

Supplemental air bag warning light

Passenger supplemental air bag OFF indicator light (except crew cab models)

Automatic transmission park warning light (

model)

Automatic transmission oil tempera- ture warning light (

model)

Door open warning light (if so equipped)

CHECKING BULBS Apply the parking brake and turn the ignition key to ON without starting the engine. The following lights come on:

or

or

If the driver side seat belt is fastened the

light will not come on.

The following lights come on briefly and then go off:

If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly.

Instruments and controls 2-7

Z X

WARNING LIGHTS

or

Anti-lock brake warn- ing light

If the light comes on while the engine is running, it may indicate the anti-lock brake system is not functioning properly. Have the system checked by an authorized NISSAN dealer. If an abnormality occurs in the system, the anti-lock function ceases but the ordinary brakes continue to operate normally. If the light comes on while you are driving, contact an authorized NISSAN dealer for repair.

Automatic transmission oil temperature warning light

model)

This light comes on when the automatic transmission oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off.

2-8 Instruments and controls

CAUTION

Continued vehicle operation when the A/T oil temperature warning light is on may damage the automatic transmis- sion.

Automatic transmission park model) warning light ( This light indicates that the automatic trans- mission parking function is not engaged. If the transfer control lever is not secured in any drive position while the automatic trans- mission selector lever is in the P (Park) position, the transmission will disengage and the vehicle may move unexpectedly. Shift the transfer control lever into the 2H, 4H, or 4L position when the warning light comes on. c When parking, always make sure that the transfer control lever is in 2H, 4H, or 4L and the parking brake is set.

c If the ATP light is ON, this indicates that the automatic transmission P (Park) po- sition will not function and the transfer lever is in the N (Neutral) position.

c Failure to engage the transfer control lever

in 2H, 4H, or 4L could result in the vehicle moving unexpectedly, resulting in serious personal injury or property damage.

WARNING

c If the ATP light is ON, this indicates that the automatic transmission P (Park) position will not function and the transfer control shift lever is in the N (Neutral) position.

or

Brake warning light

functions for both the parking

This light brake and the foot brake systems. When the ignition key is in the ON position, the light comes on when the parking brake is applied and also warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See ‘‘Brake and clutch fluid’’ in the ‘‘Do-it-yourself’’ section of this manual.

Z X

2. If the brake fluid level is correct, have the warning system checked by an autho- rized NISSAN dealer.

WARNING

c Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise have your vehicle towed because driving it could be danger- ous.

c Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop- ping distance and require greater pedal effort as well as pedal travel. c If the brake fluid level is below the MINIMUM or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at an authorized NISSAN dealer.

Charge warning light

If this light comes on while the engine is running, it may indicate the charging system

is not functioning properly. Turn the engine off and check the generator belt. If the belt is loose, broken, missing or if the light remains on, see an authorized NISSAN dealer im- mediately.

CAUTION

Do not continue driving if the belt is loose, broken or missing.

‘‘Engine oil’’ in the ‘‘Do-it-yourself’’ section of this manual.

CAUTION

Running the engine with the oil pres- sure warning light on could cause seri- ous damage to the engine almost im- mediately. Turn off the engine as soon as it is safe to do so.

Door open warning light (if so equipped)

This light comes on when any of the doors are not closed securely while the ignition key is in the ON position.

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call an autho- rized NISSAN dealer. The oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. See

Low fuel warning light

This light comes on when the fuel in the tank is low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel remaining in the tank when the fuel gauge needle reaches E (Empty).

Low washer light (Canada only)

fluid warning

This light comes on when the washer tank fluid is at a low level. Add washer fluid as necessary. See ‘‘Window washer fluid’’ in the ‘‘Do-it-yourself’’ section of this manual.

Instruments and controls 2-9

Z X

Seat belt warning light and chime

The light and chime remind you to fasten your seat belts. The light illuminates when- ever the ignition key is turned to ON or START, and remains illuminated until the driver’s seat belt is fastened. At the same time, the chime sounds for about seven seconds unless the driver seat belt is se- curely fastened. Refer to “Seat belts” in the “Seats, restraints and supplemental air bag systems” section for precautions on seat belt usage.

c The supplemental air bag warning light remains on after approximately 7 sec- onds.

c The supplemental air bag warning light

flashes intermittently.

c The supplemental air bag warning light

does not come on at all.

Unless checked and repaired, the supplemen- tal air bag system and/or the pre-tensioner seat belts may not function properly. For additional details, see the ‘‘Seats, restraints and supplemental air bag systems’’ section of this manual.

Supplemental air bag warning light

When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental air bag and pre-tensioner seat belt systems need servicing and your vehicle must be taken to an authorized authorized NISSAN dealer: 2-10 Instruments and controls

WARNING

is on,

If the supplemental air bag warning light the supplemental air bag will not operate in an accident.

it could mean that

Passenger supplemental air bag OFF indicator light (ex- cept Crew Cab models)

The passenger supplemental air bag is equipped with an ON/OFF switch. The switch is located in the center of the instru-

ment panel, near the ashtray. When the switch is turned to the ON position, the passenger supplemental air bag is enabled and could inflate in a frontal collision. When the switch is turned to the OFF position, the passenger supplemental air bag is disabled and will not inflate in a frontal collision. The passenger supplemental air bag OFF indi- cator light on the instrument panel illumi- nates when the passenger supplemental air bag ON/OFF switch is turned to the OFF position. The driver’s side supplemental air bag always remains enabled and is not affected by the passenger supplemental air bag ON/OFF switch. The key for the pas- senger supplemental air bag ON/OFF switch should not be left in the switch. Remove the key after turning the switch in the desired position. Do not leave a key in the switch. See “Passenger supplemental air bag ON/OFF switch and light” in the 9Seats, restraints and supplemental air bag systems9 section for details. INDICATOR LIGHTS

Cruise main switch indicator light (if so equipped)

The light comes on when the cruise control main switch is pushed. The light goes out

Z X

when the main switch is pushed again. While the cruise main switch indicator light comes on, the cruise control system is operational.

Cruise set indicator light (if so equipped)

The light comes on while the vehicle speed is controlled by the cruise control system. If the light blinks while the engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by your NISSAN dealer.

4-wheel drive indicator light This light comes on when the transfer shift control lever is in the 4H or 4L position.

WARNING

c When parking always make sure the transfer control lever is in the 2H, 4H or 4L position and the parking brake is applied.

c Failure to engage the transfer con- trol lever in 2H, 4H or 4L could result in the vehicle moving unexpectedly, which could cause serious personal injury or property damage.

High beam indicator light

This blue light comes on when the headlight high beams are on and goes out when the low beams are selected. The high beam indicator light also comes on when the passing signal is activated.

Malfunction indicator lamp (MIL)

If this indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control mal- function. The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel filler cap is installed and closed tightly, and that the vehicle has at least three gallons of fuel in the fuel tank.

the

lamp After a few driving trips, should turn off if no other potential emission control system malfunction exists. Operation The malfunction indicator lamp will come on in one of two ways: c Malfunction indicator lamp on steady − An emission control system malfunction has been detected. Check the fuel filler cap. filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few lamp does not driving trips. If the turn off after a few driving trips, have the vehicle inspected by an authorized NIS- SAN dealer. You do not need to have your vehicle towed to the dealer.

the fuel

If

c Malfunction indicator lamp blinking − An engine misfire has been detected which may damage the emission control sys- tem. To reduce or avoid emission control system damage: c do not drive at speeds above 45 MPH

(72 km/h).

c avoid hard acceleration or deceleration. c avoid steep uphill grades. c if possible, reduce the amount of cargo Instruments and controls 2-11

Z X

CHIMES Brake pad wear warning The disc brake pads have audible wear warnings. When a brake pad requires re- placement, it makes a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the warning sound is heard. Key reminder chime The chime sounds when the driver’s door is opened and the key is left in the ignition switch. Take the ignition key when you leave the vehicle. Light reminder chime A chime sounds if is opened with the headlight switch on unless the ignition key is in the ON position. Turn the headlight switch off when you leave the vehicle.

the driver’s door

being hauled or towed.

The malfunction indicator lamp may stop blinking and come on steady. Have the vehicle inspected by an autho- rized NISSAN dealer. You do not need to have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system.

Overdrive off indicator light (automatic transmission only)

This light comes on when the overdrive switch is pushed to the OFF position.

Turn signal/hazard indicator lights

These lights flash when the turn signal switch or hazard switch is turned on.

2-12 Instruments and controls

SECURITY SYSTEM

IC0005

VEHICLE SECURITY SYSTEM (if so equipped) The vehicle security system provides visual and audio alarm signals if parts of the vehicle are disturbed.

Z X

LIC0071

Security indicator light The security indicator light shows the status of the vehicle security system. The light operates whenever the ignition switch is in the LOCK, OFF, or ACC posi- tion. The vehicle security system has four phases. For each phase the operation of the security indicator light is different.

How to activate the vehicle security system 1. Close all windows. (The system can be the windows are

activated even if open.)

2. Remove the key from the ignition switch. 3. Close the hood and all doors. The doors can be locked using the key, power door lock switch or multi-remote controller. Multi-remote controller operation: c Push the LOCK button on the multi- remote controller. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked.

c When the LOCK button is pushed with all doors locked, the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked. The horn may or may not beep once. Refer to ‘‘silencing the horn beep feature’’ later in this section.

4. Confirm that

the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then Instruments and controls 2-13

Z X