2006 Nissan Armada Owners Manual

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs.

If replacement is required, see your NISSAN dealer for assistance.

WDI0005

REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the (cid:147)NISSAN Service and Maintenance Guide(cid:148). Do not service platinum-tipped spark plugs by cleaning or re- gapping. c Always replace spark plugs with rec-

ommended or equivalent ones.

Maintenance and do-it-yourself 8-15

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

AIR CLEANER

LDI0376
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the (cid:147)NISSAN Service and Mainte- nance Guide.(cid:148) When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.

Loosen the screw.

To remove the air cleaner filter: s1
s2 Disconnect the electrical connector. s3 Unlatch the clips and remove the air cleaner

cover. Remove the air cleaner filter.

8-16 Maintenance and do-it-yourself

WARNING

c Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn(cid:146)t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.

c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of air- borne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the (cid:147)NISSAN Service and Maintenance Guide(cid:148) for change intervals. To replace the filter, perform the following proce- dure:

LDI0480
1. Remove the 2 lower glove box hinge pins sA . Remove the glove box from the opening and let it hang by the cord.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

6. Fill out the date information on the small replacement label and attach it to the glove box lid.

LDI0387
2. Remove the filter cover bolt and remove the

filter cover.

LDI0404

NOTE:

The filters are marked with air flow arrows. The end of the filter with the arrow should face the rear of the vehicle. The arrows should face downward.

3.

Insert the first filter into the housing and slide it over to the right. Insert the second filter into the housing.

4. Replace the filter cover.

5.

Install the glove box door.

Maintenance and do-it-yourself 8-17

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

CAUTION

c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.

c Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.

WINDSHIELD WIPER BLADES

CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.

CAUTION

Worn windshield wiper blades can dam- age the windshield and impair driver vision.

8-18 Maintenance and do-it-yourself

WDI0408

REPLACING Replace the wiper blades if they are worn.

1. Lift the wiper arm away from the windshield. s2 Push the release tab, then move the wiper

blade down the wiper arm to remove.

s3 Remove the wiper blade. 4.

Insert the new wiper blade onto the wiper arm until it clicks into place.

5. Rotate wiper blade so the dimple is in the

groove.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

WDI0378
If you wax the surface of the hood, be careful not to let wax get into the washer nozzle s1 . This may cause clogging or improper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin s2 .

Maintenance and do-it-yourself 8-19

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Rear window wiper blade s1

Lift the wiper arm away from the rear win- dow.

LDI0379

s2 Push the wiper blade in and pivot until the

s3

blade becomes free. Insert a new blade onto the wiper arm and snap into place.

8-20 Maintenance and do-it-yourself

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

PARKING BRAKE AND BRAKE PEDAL

WDI0293

WDI0229

CHECKING PARKING BRAKE From the released position, firmly push the park- ing brake down. If the number of clicks is out of the range listed, see a NISSAN dealer. c 3(cid:150)4 clicks under depressing force of 44.1 lb

(196 N).

CHECKING BRAKE PEDAL With the engine running, check the distance A between the upper surface of the pedal and the metal floor. If it is out of the range shown, see a NISSAN dealer. Distance A: Under depression force of 110 lb (490 N)

3 1/2 in (90 mm) or more Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes.

The front and rear disc-type brakes self-adjust every time the brake pedal is applied.

WARNING

See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148).

Maintenance and do-it-yourself 8-21

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step.

2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, stop the engine. Keep the pedal depressed for about 30 seconds. The pedal height should not change.

4. Run the engine for one minute without de- pressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is re- leased from the booster.

If the brakes do not operate properly, have the brakes checked by a NISSAN dealer.

8-22 Maintenance and do-it-yourself

FUSES

LDI0455
Two types of fuses are used. Type A is used in the fuse boxes in the engine compartment. Type B is used in the passenger compartment fuse box. Type A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type A fuses can be installed in the engine com- partment and passenger compartment fuse boxes.

LDI0457
If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely. Type B fuses cannot be installed in the under- hood fuse boxes. Only use type A fuses in the underhood fuse boxes.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

3. Remove the fuse box cover by pushing the

tab and lifting the cover up.

4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.

LDI0380

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not come on, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the engine hood.

5.

6.

WDI0452
If the fuse is open sA , replace it with a new fuse sB . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.

Maintenance and do-it-yourself 8-23

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

LDI0381

WDI0452

LDI0456

4.

Type A

If the fuse is open sA , replace it with a known good fuse sB .

5. Push the fuse box cover to install. 6.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Type B

PASSENGER COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight

switch are OFF.

2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller. 8-24 Maintenance and do-it-yourself

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

KEYFOB BATTERY REPLACEMENT

Replace the battery in the keyfob as follows: s1 Open the lid using a coin sA . s2 Remove the battery sB . s3

Install a new battery sC with the (cid:147)+(cid:148) facing down.

LDI0484
Recommended battery: CR2025 or equivalent. s4 Close the lid securely. 5. Press the

button, then the

button two or three times to check the key- fob operation.

If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

Maintenance and do-it-yourself 8-25

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

LIGHTS

HEADLIGHTS Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Be- cause the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.

CAUTION

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c When handling the bulb, do not touch

the glass envelope.

c DO NOT TOUCH THE BULB

8-26 Maintenance and do-it-yourself

c Use the same number and wattage as

originally installed: Low beam:

Wattage: 51
Bulb no.: 9006*

High beam:

Wattage: 60
Bulb no.: 9005*

*: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.

c Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture and smoke may enter the headlight body and affect the per- formance of the headlight.

c Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.

FOG LIGHTS (if so equipped) Replacing the fog light bulb

CAUTION

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c When handling the bulb, do not touch

the glass envelope.

c Use the same number and wattage as

originally installed: Wattage 37.5 Bulb No. 899* *: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.

c Do not leave the bulb out of the fog light for a long period of time as dust, mois- ture and smoke may enter the fog light body and affect the performance of the fog light.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

LDI0382

1. Disconnect the negative (-) battery cable.

2. The fog light is accessible in front of the front

tire and behind the bumper.

3. Disconnect the bulb connector s1 . 4. Rotate the bulb counterclockwise and re-

move.

5. Remove by pulling it straight out of the fog light assembly. Do not shake or rotate the bulb when removing it. Do not touch the glass envelope.

6.

Install in the reverse order of removal.

NOTE: To adjust the fog light vertical aim: Access the aiming screw from underneath the front bumper. The aiming screw is located on the bottom of the fog light housing. Turn the screw clockwise to raise the pattern. Turn the screw counterclockwise to lower the pattern.

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.

Headlight assembly

High Low Park/Turn Sidemarker

Side turn signal light* (if so equipped) Front fog light Puddle lamp Room/map lights Personal lights Footwell Glove box light Vanity mirror light Step light Cargo light High-mounted stop light* Rear combination light

Tail/Stop Backup (reversing) Turn

License plate light

60
51
8/27
3.8

(LED)

27
13
3.4
3.4
1.8
3.8

(cid:151)

7/27
18
27

HB3/9005
HB4/9006
3157AK

194

(cid:151)

881
906
(cid:150)

2GL T2P

158
158
(cid:150) 194
28

(cid:151)

3157K

921

3156K

168

* See a NISSAN dealer for replacement.

Always check with the Parts Department at a NISSAN dealer for the latest parts information.

Maintenance and do-it-yourself 8-27

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

1. 2. 3. 4.

Room/map light Front personal lights Step light Puddle lamp/Side turn signal light (if so equipped)

5. High-mount stoplight 6. Cargo light 7. 8. 9. Headlight assembly 10. Fog light

License plate light Rear combination light

8-28 Maintenance and do-it-yourself

LDI0383

WDI0263

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.

first remove the lens,

Indicates bulb removal Indicates bulb installation

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Personal lights (cid:150) Type A Use a cloth s1 to protect the housing.

Vanity mirror

Use a cloth s1 to protect the housing.

LDI0364

LDI0385

Room/map lights

Use a cloth s1 to protect the housing.

LDI0389

Maintenance and do-it-yourself 8-29

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Use a cloth s1 to protect the housing.

Step light

Puddle light

Use a cloth s1 to protect the housing.

Use a cloth s1 to protect the housing.

Cargo light

LDI0341

LDI0388

WDI0233

8-30 Maintenance and do-it-yourself

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

License plate light

LDI0384

Rear combination light

WDI0403

WHEELS AND TIRES

If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Low tire pressure warning system This vehicle is equipped with the low tire pres- sure warning system. It monitors tire pressure of all tires except the spare. When the low tire pressure monitoring system warning light is lit, one or more of your tires is significantly underin- flated. If equipped, the system also displays pres- sure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel.

The low tire pressure warning system will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h). Also, this system may not detect a sudden drop in tire pressure (for ex- ample a flat tire while driving).

For more details, refer to (cid:147)Low tire pressure warn- ing light(cid:148) in the (cid:147)Instruments and controls(cid:148) sec- tion, (cid:148)Tire pressure information(cid:148) in the (cid:147)Display screen, heater, air conditioner and audio sys- tems(cid:148) section, (cid:147)Low tire pressure warning sys- tem(cid:148) in the (cid:147)Starting and driving(cid:148) section, and (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section.

Maintenance and do-it-yourself 8-31

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.

WARNING

c Improperly inflated tires can fail suddenly and cause an accident. c The Gross Maximum Weight rat- ing is located on the FMVSS la- bel. The vehicle weight capacity is indicated on the Tire and Load- ing Information label (if so equipped). Do not load your ve- hicle beyond this capacity. Over- loading your vehicle may result in reduced tire life, unsafe operat- ing conditions due to premature tire failure, or unfavorable han- dling characteristics and could also lead to a serious accident. Loading beyond the specified ca- pacity may also result in failure of other vehicle components.

Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long dis- tance trips. The recommended tire pres- sure specifications are shown on the FM- VSS label or the Tire and Loading Information label (if so equipped) under the 9Recommended Cold Tire Inflation Pressure9 heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds.

8-32 Maintenance and do-it-yourself

c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

c Do not drive your vehicle over 85
MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire fail- ure, loss of control and possible injury.

c For additional

information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.

Safety

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later

in this section. and s7 Spare tire size or compact spare tire size (if so equipped).

s6

LDI0392

Type A

Tire and loading information label (if so equipped) s1 Seating capacity: The maximum num- ber of occupants that should be seated in the vehicle.

s2 Vehicle load limit: See loading infor- mation in the (cid:147)Technical and con- sumer information(cid:148) section.

s3 Original tire size: The size of the tires originally installed on the vehicle at the factory.

s4 Recommended cold tire inflation pressure: Inflate the tires to this pres- sure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicles GVWR.

speeds.

The

Maintenance and do-it-yourself 8-33

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

s4 Original tire size: The size of the tires originally installed on the vehicle at the factory.

s5 Spare tire size or compact spare tire

size (if so equipped).

LDI0434

Tire and loading information label (for US) s1 Seating capacity: The maximum num- ber of occupants that should be seated in the vehicle.

s2 Vehicle load limit: See loading infor- mation in the (cid:147)Technical and con- sumer information(cid:148) section.

8-34 Maintenance and do-it-yourself

Type B

s3 Recommended cold tire inflation pressure: Inflate the tires to this pres- sure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate recom- mended cold tire inflation is set by the manufacturer to provide the best bal- ance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicles GVWR.

speeds.

The

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

LDI0393

Checking tire pressure 1. Remove the valve stem cap from the

tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leak- age.

3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare to the specifica- tion shown on the Tire and Loading Information label.

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.

6. 7. Check the pressure of all other tires,

including the spare.

Size

Front Original Tire: P285/70R17
P265/70R18
Rear Original Tire: P285/70R17
P265/70R18
Spare Tire: P285/70R17
P265/70R18

Cold Tire Inflation Pressure

240 kPa, 35 PSI

240 kPa, 35 PSI

240 kPa, 35 PSI

Maintenance and do-it-yourself 8-35

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

WDI0394

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information iden- tifies and describes the fundamental characteristics of the tire and also pro- vides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

8-36 Maintenance and do-it-yourself

s1 Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is de-

signed for passenger vehicles.

2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.

3. Two-digit number: This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width. 4. R: The 9R9 stands for radial.

WDI0395
5. Two-digit number: This number is the

wheel or rim diameter in inches.

6. Two- or

three-digit number: This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. Tire speed rating. You should not drive the vehicle faster than the tire speed rating.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

s2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Depart- ment Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Num- ber.

2. Two-digit

code: Manufacturer(cid:146)s

identification mark

3. Two-digit code: Tire size

The number of layers or plies of rubber- coated fabric in the tire. Tire manufactur- ers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. s4 Maximum permissible inflation pres- sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible in- flation pressure. s5 Maximum load rating This number indicates the maximum load in kilograms and pounds that can be car- ried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory in- stalled tire. s6 Term of (cid:148)tubeless(cid:148) or (cid:148)tube type(cid:148) Indicates whether the tire requires an in- ner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). s7 The word (cid:148)radial(cid:148)

Maintenance and do-it-yourself 8-37

WDI0396
4. Three-digit code: Tire type code

(Optional)

5. Three-digit code: Date of Manufac-

ture

6. Four numbers represent the week and year the tire was built. For ex- ample, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.

s3 Tire ply composition and material

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

The word 9radial9 is shown if the tire has radial structure. s8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the out- ward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle.

8-38 Maintenance and do-it-yourself

TYPES OF TIRES

WARNING

c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.

c Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.

c Replacing tires with those not originally specified by NISSAN could affect the proper operation of the low tire pres- sure warning system.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ-

ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas. Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.

If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle.

If you do not,

Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or underbody. If possible, avoid fully load- ing your vehicle when using tire chains. In addi- tion, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and performance may be adversely affected. Tire chains must be installed only on the rear wheels and not on the front wheels. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress. Use only the 2WD range when driving on clear paved roads.

If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels.

For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use only SAE class (cid:147)S(cid:148) chains. Class 9S9 chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class (cid:147)S(cid:148) chains are de- signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tire size. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufac- turer to ensure a tight fit. Loose end links of the

WDI0258

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emer- gency(cid:148) section in this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Maintenance and do-it-yourself 8-39

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Wheel nut tightening torque:

98 ft-lb (133 N•m)

The wheel nuts must be kept tight- ened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval.

WARNING

c After rotating the tires, check and

adjust the tire pressure.

c Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

c Do not include the spare tire in

the tire rotation. c For additional

information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.

Safety

c The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced.

c Improper service of the spare tire may result in serious personal in- jury. If it is necessary to repair the spare tire, contact a NISSAN dealer.

c For additional

information re- garding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Information(cid:148) (Canada) in the Warranty Infor- mation Booklet.

Safety

Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

WDI0259

1. Wear indicator 2. Location mark Tire wear and damage

WARNING

c Tires should be periodically in- spected for wear, cracking, bulg- ing or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.

8-40 Maintenance and do-it-yourself

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. is not

retread tires

c The use of recommended. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

WARNING

c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.

c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.

this manual

with

the

Four-wheel drive models

CAUTION

Always use tires of the same type, size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires on the front and rear axles which will cause excessive tire wear and may dam- age the transmission, transfer case and differential gears.

If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.

Maintenance and do-it-yourself 8-41

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .

Care of wheels c Wash the wheels when washing the vehicle

to maintain their appearance.

c Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

c Do not use abrasive cleaners when washing

the wheels.

c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

8-42 Maintenance and do-it-yourself

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation . . . . . . . . . . . 9-5
Recommended SAE viscosity number . . . . . . . . . . . . 9-6
Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . 9-8

When traveling or registering your vehicle in another country . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle identification number (VIN) plate . . . . . . . . . . 9-9
Vehicle identification number (chassis number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Engine serial number. . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . 9-10
Emission control information label . . . . . . . . . . . . . . . 9-10
Tire and loading information label. . . . . . . . . . . . . . . . 9-11
Air conditioner specification label. . . . . . . . . . . . . . . . 9-11

Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
Securing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Loading tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-15
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . 9-15
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Maximum load limits . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Towing load/specification. . . . . . . . . . . . . . . . . . . . . . . 9-17
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
Flat towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Snow plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Emission control system warranty . . . . . . . . . . . . . . . . . . 9-26
Reporting safety defects (US only) . . . . . . . . . . . . . . . . . 9-27
Readiness for inspection/maintenance (I/M) test . . . . . 9-27
Event data recorders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-28
Owner(cid:146)s Manual/Service Manual order information . . . 9-28
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . 9-29

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS

The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the (cid:147)Maintenance and do-it-yourself(cid:148) section to determine the proper refill capacity.

Fuel Engine oil *7

Drain and Refill

With oil filter change Without oil filter change

Capacity (Approximate) US measure 28 gal

Imp measure 23-1/4 gal

6-1/2 qt 6-1/4 qt

5-1/2 qt 5-1/4 qt

Cooling system

With reservoir

3-3/4 gal

3-1/8 gal

Liter 105.8

6.2
5.9

14.4

Automatic transmission fluid Power steering fluid (PSF) Brake fluid Multi-purpose grease Air conditioning system refrigerant Air conditioning system oil Transfer fluid

Refill to the proper level according to the instructions in the (cid:147)Maintenance and do-it-yourself(cid:148) section.

(cid:151) (cid:151) (cid:151) (cid:151)

(cid:151) (cid:151) (cid:151) (cid:151)

(cid:151) (cid:151) (cid:151) (cid:151)

Recommended Fluids and Lubricants

Unleaded gasoline with an octane rating of at least 87 AKI (RON 91)*1

(cid:149) API Certification Mark *2 *3
(cid:149) API grade SG, Energy Conserving II or API grade SH, SJ or SL*2 *3
(cid:149) ILSAC grade GF-II or GF-III*2 *3

50% Genuine NISSAN Long Life Antifreeze/Coolant or equivalent 50% Demineralized or distilled water Genuine NISSAN Matic J ATF *4
Genuine NISSAN PSF or equivalent.*8
Genuine NISSAN Super Heavy Duty Brake Fluid*5 or equivalent DOT 3
NLGI No. 2 (Lithium Soap base) HFC-134a (R-134a)*6
NISSAN A/C System Oil Type S (DH-PS) or equivalent*6
Genuine NISSAN Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid*8, *10
API GL-5 Viscosity SAE 80W-90*9, *10
API GL-5 Viscosity SAE 80W-90*9, *10
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze fluid or equivalent

(cid:151) (cid:151) 4.5

(cid:151) (cid:151) 1 gal

(cid:151) (cid:151) 1-1/4 gal

Front final drive oil Rear final drive oil Windshield washer fluid (shared between front and rear wipers) *1: For further details, see (cid:147)Fuel recommendation.(cid:148) *2: For further details, see (cid:147)Engine oil and oil filter recommendations.(cid:148) *3: For further details, see (cid:147)Recommended SAE viscosity number.(cid:148) *4: Using automatic transmission fluid other than Genuine NISSAN Matic J ATF will cause deterioration in driveability and automatic transmission durability, and may damage the auto- matic transmission, which is not covered by the NISSAN new vehicle limited warranty. *5: Available in mainland USA through your NISSAN dealer. *6: For further details, see (cid:147)Air conditioner specification label.(cid:148) *7: For further details, see (cid:147)Changing engine oil.(cid:148) *8: For Canada, NISSAN Automatic Transmission Fluid (ATF), DEXRON(cid:153) III/MERCON(cid:153), or equivalent ATF may also be used. *9: For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 0(cid:176) C (32(cid:176) F). *10: See your NISSAN dealer for service.

9-2 Technical and consumer information

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91).

CAUTION

c Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.

c Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst.

Reformulated gasoline Some fuel suppliers are now producing reformu- lated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxy- genates such as ethanol, MTBE and methanol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel com-

patibility for your NISSAN cannot be readily de- termined. If in doubt, ask your service station manager.

If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. than methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

c If an oxygenate-blend other

c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not avail- able to ensure that all methanol blends are suitable for use in NISSAN ve- hicles.

fuels,

oxygenate-blend

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel additives (for example, fuel injec- tor cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy (cid:147)spark knock.(cid:148) ((cid:147)Spark knock(cid:148) is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the Technical and consumer information 9-3

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

c U.S. government

regulations require ethanol dispensing pumps to be identi- fied by a small, square, orange and black label with the common abbrevia- tion or the appropriate percentage for that region.

condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible.

ignition timing may result

Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine damage. If any of the above symptoms are en- countered, have your vehicle checked at a NISSAN dealer. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

CAUTION

c Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.

c E-85 is a mixture of approximately 85% 15% unleaded

ethanol

and

fuel gasoline.

9-4 Technical and consumer information

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose engine oil with the cor- rect quality and viscosity to ensure satisfactory engine life and performance. NISSAN recom- mends the use of a low friction oil (energy con- serving oil) in order to improve fuel economy and conserve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage.

Only those engine oils with the American Petro- leum Institute (API) CERTIFICATION MARK on

WTI0082
the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories.

If you cannot find engine oil with the API CERTI- FICATION MARK, use API grade SL Energy Conserving oil. An oil with a single designation SL, or in combination with other categories (for example, SL/CF) may also be used if one with the API CERTIFICATION MARK cannot be found. An ILSAC grade GF-II or GF-III oil can also be used.

NISSAN recommends mineral based oils. These oils must, however, meet the API quality and SAE viscosity ratings specified for your vehicle.

Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not neces- sary when the proper oil type is used and main- tenance intervals are followed.

Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be oper- ated before the next oil change. The chart (cid:147)Rec- ommended SAE viscosity number(cid:148) shows the recommended oil viscosities for the expected ambient temperatures. Choosing an oil viscosity other than that recommended could cause seri- ous engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When re- placing, use a genuine NISSAN oil filter or its equivalent for the reason described in (cid:147)Change intervals(cid:148).

Technical and consumer information 9-5

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using engine oil and filters that are not of the specified quality, or exceeding recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incor- rect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle warranty. Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: c repeated short distance driving at cold out-

side temperatures

c driving in dusty conditions c extensive idling c towing a trailer c stop and go commuting

9-6 Technical and consumer information

ATI1028

RECOMMENDED SAE VISCOSITY NUMBER c SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0(cid:176)F (-18(cid:176)C).

AIR CONDITIONER SYSTEM REFRIGERANT AND OIL RECOMMENDATIONS The air conditioner system in your NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the oil, NISSAN A/C system oil DH-PS or the exact equiva- lents.

CAUTION

The use of any other refrigerant or oil will cause severe damage to the air condition- ing system and will require the replace- ment of all air conditioner system components.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth(cid:146)s ozone layer. Although this refrigerant does not affect the earth(cid:146)s atmosphere, certain government regula- tions require the recovery and recycling of any refrigerant during automotive air conditioner sys- tem service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refriger- ant. Contact a NISSAN dealer when servicing your air conditioner system.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

SPECIFICATIONS

ENGINE

Model

Type Cylinder arrangement Bore x Stroke Displacement Firing order

Idle speed

A/T (in (cid:147)N(cid:148) position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle

Spark plug

Spark plug gap (Nominal)

VK56DE

Gasoline, 4-cycle, DOHC 8-cylinder, V-block, Slanted at 90(cid:176)

in (mm) 3.858 x 3.622 (98 x 92)

cu in (cm3) 338.78 (5,552)

1(cid:150)8(cid:150)7(cid:150)3(cid:150)6(cid:150)5(cid:150)4(cid:150)2

See the (cid:147)Emission Control Information label(cid:148) on the under- side of the hood.

Standard PLFR5A-11

Hot PLFR4A-11
Cold PLFR6A-11

in (mm) 0.043 (1.1)

Camshaft operation The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Timing chain

Technical and consumer information 9-7

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Wheels

Tires

Spare tire

17 x 7.5J 18 x 8.0J

P285/70R17
P265/70R18
Full size

9-8 Technical and consumer information

Overall length Overall width Overall height

2wd with roof rack 4wd with roof rack 2wd without roof rack 4wd without roof rack

Front tread

17 inch tire 18 inch tire

Rear tread

17 inch tire 18 inch tire

Wheelbase

Gross vehicle weight rating Gross axle weight rating

Front Rear

in (mm) 206.9(5,255) in (mm) 78.8(2,001)

in (mm) in (mm) in (mm) in (mm)

77.8(1,977) 78.7(1,998) 75.7(1,922) 76.5(1,944)

in (mm) in (mm)

67.5(1,715) 67.9(1,725)

67.5(1,715) in (mm) in (mm) 67.9(1,725) in (mm) 123.2(3,130) lb (kg) See the (cid:147)F.M.V.S.S.

certification label(cid:148) on the center pillar between the driver(cid:146)s side front and side doors.

lb (kg) lb (kg)

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle(cid:146)s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emis- sion control and safety standards vary according to the country, state, province or district; there- fore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

VEHICLE IDENTIFICATION

LTI0085
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number (VIN) plate is attached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.

LTI0086
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.

Technical and consumer information 9-9

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

WTI0095

WTI0099

LTI0087

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.

EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.

information label

is at-

9-10 Technical and consumer information

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

INSTALLING FRONT LICENSE PLATE

WTI0100
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown.

WTI0155
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is affixed as shown.

LTI0093

Use the following steps to mount the front license plate: 1. Make holes on the plastic finisher at the location mark (small dimple) using a 0.20 in (5 mm) drill. Apply light pressure to the drill. Install the license plate holder using the two screws provided with the holder.

2. Mount the license plate using two M6-

14mm bolts. License plate bolt tightening torque:

3.8 - 4.7 ft-lb (5.10 - 6.37 N•m)

Technical and consumer information 9-11

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

VEHICLE LOADING INFORMATION

WARNING

c It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.

c Be sure everyone in your vehicle is in a seat and using a seat belt properly.

TERMS It is important to familiarize yourself with the following terms before loading your vehicle: c Curb Weight (actual weight of your vehicle) - vehicle weight including: standard and optional equipment, flu- ids, emergency tools, and spare tire assembly. This weight does not in- clude passengers and cargo.

9-12 Technical and consumer information

c GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

c GVWR (Gross Vehicle Weight Rat- ing) - maximum total combined weight of the unloaded vehicle, pas- sengers, trailer tongue load and any other optional equipment. This information is lo- cated on the F.M.V.S.S. label.

luggage,

hitch,

c GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle. This informa- tion is located on the F.M.V.S.S. label. c GCWR (Gross Combined Weight rating) - The maximum total weight rating of the vehicle, passengers, cargo, and trailer.

limit specified of

c Vehicle Capacity Weight, Load limit, Total load capacity - maximum total weight the load (passengers and cargo) for the ve- hicle. This is the maximum combined weight of occupants and cargo that can be loaded into the vehicle. If the

vehicle is used to tow a trailer, the trailer tongue weight must be in- cluded as part of the cargo load. This information is located on the Tire and Loading Information label (if so equipped).

c Cargo capacity - permissible weight of cargo, the subtracted weight of occupants from the load limit.

VEHICLE LOAD CAPACITY Do not exceed the load limit of your ve- hicle shown as 9The combined weight of occupants and cargo9 on the Tire and Loading Information label. Do not exceed the number of occupants shown as 9Seating Capacity9 on Tire and Loading Information label. To get 9the combined weight of occu- pants and cargo9, add the weight of all occupants, then add the total luggage weight. Examples are shown below.

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

Steps for determining correct load limit 1. Locate the statement (cid:147)The combined weight of occupants and cargo should never exceed XXX lbs(cid:148) on your vehicle(cid:146)s placard.

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.

4. The resulting figure equals the avail- able amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capac- ity is 650 lbs. (1400-750 (5 * 150) = 650 lbs) or (640-340 (5 * 70) = 300
kg.)

LTI0152

Technical and consumer information 9-13

Z REVIEW COPY—2006 Armada (wzw) Owners Manual—USA_English (nna) 06/16/05—debbie X

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the available cargo and lug- gage load capacity of your vehicle.

6.

Before driving a loaded vehicle, confirm the you do not exceed the Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR) for your vehicle. See (cid:147)Measurement of Weights(cid:148) later in this section. Also check tires for proper inflation pres- sures. See the Tire and Loading label.

9-14 Technical and consumer information

Cargo area ceiling tie-down hooks

Cargo area floor tie-down hooks

LTI0089

LTI0090

SECURING THE LOAD There are tie down hooks located in the cargo area as shown. The tie down hooks can be used to secure cargo with ropes or other types of straps. Do not apply a total load of more than 55
lbs. (245 N) to a single sA plastic hook or 44
lbs. (196 N) to a single sB plastic hook