Login- Download PDF Manual
-
Checking compatibility
If this symbol appears on the package or in the instructions supplied with the original hand-held transmitter, you can assume that the radio remote control device is compatible with the integrated universal remote control. For additional information, please contact your MINI dealer or call: 1-800-355-3515. You can also obtain information on the Internet at: www.MINI.com or
76
Programming
1 Memory buttons 2 LED
Fixed-code hand-held transmitters 1. Switch on the ignition, page 38. 2. When starting operation for the first time:
Press both outer memory buttons 1 for approx. 20 seconds until the LED 2 flashes rapidly. All stored programs are cleared.
3. Hold the original hand-held transmitter at a distance of approx. 2 in to 12/5 to 30 cm in from the memory buttons 1.
The required distance between the hand-held transmitter and the mem- ory buttons 1 depends on the system of the respective original hand-held transmitter used.<
4. Simultaneously press the transmit key on the original hand-held transmitter and the desired memory button 1 on the integrated universal remote control. The LED 2 flashes slowly at first. As soon as the LED 2 flashes rapidly, release both buttons. If the LED 2 does not flash rapidly after approx. 15 sec- onds, alter the distance.
5. To program other original hand-held trans-
mitters, repeat steps 3 and 4.
The corresponding memory button 1 is now programmed with the signal of the original hand-held transmitter. You can operate the system with the engine running or with the ignition switched on.
If the system fails to function even after repeated programming, check whether
the original hand-held transmitter uses an alter- nating-code system. To do so, either read the instructions for the original hand-held transmit- ter or hold down the programmed memory button 1 of the integrated universal remote con- trol. If the LED 2 on the integrated universal remote control flashes rapidly and then remains lit for about two seconds, the original hand-held transmitter uses an alternating-code system. If it uses an alternating-code system, program the memory buttons 1 as described under Alternat- ing-code hand-held transmitters.<
Alternating-code hand-held transmitters To program the integrated universal remote control, consult the operating instructions for the device to be set. You will find information there on the possibilities for synchronization or programming of additional hand-held transmit- ters. When programming hand-held transmitters that employ an alternating code, please observe the following supplementary instructions:
The corresponding memory button 1 is now programmed with the signal of the original hand-held transmitter.
Clearing stored programs Press both outer memory buttons 1 for approx. 20 seconds until the LED 2 flashes: all stored programs are cleared. It is not possible to clear individual programs.
Reassigning individual programs 1. Hold the original hand-held transmitter at a distance of approx. 2 in to 12/5 to 30 cm in from the memory buttons 1.
The required distance between the hand-held transmitter and the mem- ory buttons 1 depends on the system of the respective original hand-held transmitter used.<
2. Press the desired memory button 1 of the
3.
integrated universal remote control. If the LED 2 flashes slowly after approx. 20 seconds, press the transmit key of the original hand-held transmitter and release both buttons as soon as the LED 2 flashes rapidly. If the LED 2 does not flash rapidly after approx. 15 seconds, alter the distance and repeat this step.
Programming will be easier with the aid of a second person.<
Glove compartment
1. Park your vehicle within the range of the
remote-controlled device.
2. Program the integrated universal remote control as described above in the section Fixed-code hand-held transmitters.
3. Locate the button on the receiver of the
device to be set, e.g. on the drive unit. 4. Press the button on the receiver of the device to be set. After step 4, you have approx. 30 seconds for the next step 5.
5. Press the programmed memory button 1 of
the integrated universal remote control three times.
Opening
Press the button to open the cover. The light in the glove compartment comes on.
77
Closing Fold cover up.
To prevent injury in the event of an acci- dent, close the glove compartment after
use while the vehicle is being driven.<
Ventilation* Depending on your vehicle's equipment, the glove compartment can be ventilated and, if the cooling function* is switched on, can also be cooled.
Opening Rotate the switch in the direction of the arrow.
Closing Rotate the switch in the opposite direction of the arrow until it is in the vertical position. Depending on the temperature setting of the air conditioning or the automatic climate control, high temperatures may result in the glove com- partment.
Center armrest*
Storage compartment The center armrest between the front seats con- tains either a compartment or the cover for the mobile phone base plate* or the snap-in adapter*.
78
Opening The cover slides along guide rails and can be opened fully by pushing it back and lifting it.
Closing Push the cover forwards.
Connection for external audio device > iPods/iPhones or USB devices such as MP3 players and USB memory sticks: connect via the USB audio interface.
> iPhone/mobile phone music players: con- nect via the snap-in adapter*, refer to the separate Owner's Manual. Playback is only possible if there is no device connected to the USB audio interface.
Connecting via the USB audio interface
1 Connection for audio playback:
TRS connector 1/8"/3.5 mm
2 USB interface*
Apple iPod/iPhone To connect the device, use the special cable adapter for the Apple iPod/iPhone, available from your dealer. The cable adapter is required for a flawless connection. For additional information, contact your MINI dealer or visit the Internet at www.MINI.com/ usb To play audio tracks over the car's speaker sys- tem, connect the iPod to ports 1 and 2. The iPod/iPhone's menu structure is supported by the USB audio interface.
USB device To play audio tracks over the car's speaker sys- tem, connect the USB device to port 2.
Notes
Do not expose the audio device to extreme environmental conditions, e.g. very high temperatures, refer to the Owner's Manual of the audio device. Otherwise, the audio device may become damaged, which could compromise safety while driving.< > The USB audio interface supplies the con-
nected audio devices with power, provided that this is supported by the audio device. Therefore, do not connect the USB audio device to the power socket in the vehicle during operation.
> Do not forcibly connect the plug to the USB
interface.
> Do not connect devices such as fans or
lamps to the USB audio interface.
> Do not connect USB hard disks. > Do not use the USB audio interface to charge
external devices.
Storage compartments
In the vehicle interior Depending on your vehicle's equipment, you will find storage compartments in the doors, next to the rear seats and in the center console*.
Nets* are located in the passenger footwell and on the backs of the front seat backrests.
Storage compartment on the front passenger side*
Opening Briefly press the bottom edge of the cover.
Closing Push the cover back into its original position.
To prevent injury in the event of an acci- dent, close the storage compartment after
use while the vehicle is being driven.<
Clothes hooks There are clothes hooks on the grab handles in the rear passenger compartment.
Items of clothing hung from the hooks must not obstruct the driver's view. Do not hang heavy objects from the hooks; otherwise, they could endanger the car's occupants, e.g. in case of heavy braking or sudden swerving.<
In the cargo bay Depending on your vehicle's equipment, you have the following storage options: > Umbrella holder* under the loading sill in
front of the warning triangle
> Storage compartment under the level load
floor*
> Removable box with lid* under the level
load floor, e.g. for wet or dirty items
> Storage compartment in the splitdoor > Net* on the cargo bay floor for smaller objects; for attaching to the lashing eyes
79
s
When leaving the car, always remove the key so that children cannot operate the cigarette lighter and burn themselves.<
Connecting electrical appliances In your MINI, you can use electrical devices such as a flashlight, car vacuum cleaner, etc., up to approx. 200 watts at 12 volts, as long as one of the following sockets is available. Avoid damag- ing the sockets by attempting to insert plugs of unsuitable shape or size.
Cigarette lighter socket Remove the lighter* or cover from the socket.
Power socket in cargo bay
By way of example, the illustration shows the cargo bay in the MINI. Pull out the cover.
Cupholders and ashtray*
Cupholders Two cupholders are located in the front of the center console; another is in the rear at the back of the center console. There are two additional cupholders in the arm rests in the rear.
Do not place glass containers in the cup- holders, as this increases the risk of injury
in the event of an accident.<
Ashtray* The ashtray is located in one of the cupholders in the center console.
Emptying Remove the entire ashtray.
Lighter With the engine running or the ignition switched on, press in the cigarette lighter. The lighter can be pulled out as soon as it pops back out.
Hold or touch the hot cigarette lighter by the knob only. Holding or touching it in
other areas could result in burns.
80
E
81
AT A GLANCE
CONTROLS
DRIVING TIPS
DRIVING TIPS
MOBILITY
REFERENCE
Things to remember when driving
Break-in period Moving parts need breaking-in time to adjust to each other. Please follow the instructions below in order to achieve the optimal service life and economy of operation for your vehicle.
Following part replacement The same break-in procedures should be observed if any of the components mentioned above have to be renewed in the course of the vehicle's operating life.
Engine and differential Always obey all official speed limits.
Up to 1,200 miles/2,000 km Drive at varying engine and road speeds, but do not exceed the following: > Gasoline engine
4,500 rpm or 100 mph/160 km/h
Avoid full-throttle operation and use of the transmission's kickdown mode.
After driving 1,200 miles/2,000 km Engine and vehicle speeds can be gradually increased.
Tires Due to technical factors associated with their manufacture, tires do not achieve their full trac- tion potential until after an initial break-in period. Therefore, drive cautiously during the first 200 miles/300 km.
Brake system Brakes require an initial break-in period of approx. 300 miles/500 km to achieve optimized contact and wear patterns between brake pads and rotors. Drive cautiously during this break-in period.
Clutch The function of the clutch reaches its optimal level only after a distance driven of approx. 300 miles/500 km. During this break-in period, engage the clutch gently.
84
General driving notes
Close splitdoor
Drive the vehicle only when the splitdoor is closed. Otherwise, exhaust fumes could
penetrate the interior of the vehicle.< If special circumstances make it absolutely nec- essary to drive with the splitdoor open: 1. Close all windows and the glass sunroof*. 2. Switch off the recirculated-air mode and sig- nificantly increase the air flow rate of the air conditioner or automatic climate control, page 72 or 74.
Hot exhaust system
In all vehicles, extremely high tempera- tures are generated in the exhaust sys- tem. Do not remove the heat shields installed adjacent to various sections of the exhaust sys- tem, and never apply undercoating to them. When driving, standing at idle and while park- ing, take care to avoid possible contact between the hot exhaust system and any highly flamma- ble materials such as hay, leaves, grass, etc. Such contact could lead to a fire, with the risk of seri- ous personal injuries and property damage. Do not touch hot exhaust tail pipes. Otherwise, there is a risk of burns.<
Hydroplaning
When driving on wet or slushy roads, reduce road speed. If you do not, a wedge
of water can form between tires and road sur- face. This situation, known as hydroplaning, can cause partial or complete loss of tire contact with the road surface, so that the car cannot be steered or braked properly.<
The risk of hydroplaning increases with declining tread depth on the tires, refer also to Tread depth on page 102.
Driving through water
Drive through water on the road only if it is not deeper than 1 ft/30 cm, and then only
at walking speed at the most. Otherwise, the vehicle's engine, the electrical systems and the transmission may be damaged.<
Parking brake on inclines
On inclines, do not hold the vehicle with the clutch; use the parking brake. Other-
wise, greater clutch wear will result.< For information on driving off using Hill Assist*, refer to page 58.
Braking safely Your MINI is equipped with ABS. If you are in a situation which requires full braking, it is best to brake using maximum brake pressure. Since the vehicle maintains steering responsiveness, you can still avoid possible obstacles with a mini- mum of steering effort. The pulsation of the brake pedal, together with the sound of hydraulic regulation, indicates that ABS is actively taking effect.
Driving in wet conditions When roads are wet or there is heavy rain, briefly exert gentle pressure on the brake pedal every few miles. Monitor traffic conditions to ensure that this maneuver does not endanger other road users. The heat generated in this process helps dry the pads and rotors to ensure that Then full braking force will be immediately avail- able when it is needed.
Hills
To prevent overheating and the resulting reduced efficiency of the brake system, drive long or steep downhill gradients in the gear in which the least braking is required. Even light but consistent brake pressure can lead to high temperatures, brake wear and possibly even brake failure.<
You can increase the engine's braking effect by shifting down, all the way to first gear if neces- sary. This strategy helps you avoid placing excessive loads on the brake system. Downshift- ing in manual mode of the automatic transmis- sion, page 41.
Never drive with the clutch held down, with the transmission in neutral or with
the engine switched off; otherwise, engine brak- ing action will not be present or there will be no power assistance to the brakes or steering. Never allow floor mats, carpets or any other objects to protrude into the area around the pedals; otherwise, pedal function could be impaired.<
Corrosion on brake rotors When the vehicle is driven only occasionally, during extended periods when the vehicle is not used at all, and in operating conditions where brake applications are less frequent, there is an increased tendency for corrosion to form on rotors, while contaminants accumulate on the brake pads. This occurs because the minimum pressure which must be exerted by the pads during brake applications to clean the rotors is not reached. Should corrosion form on the brake rotors, the brakes will tend to respond with a pulsating effect that even extended application will fail to cure.
When the vehicle is parked Condensation forms while the automatic climate control is in operation, and then exits under the vehicle. Traces of condensed water under the vehicle are therefore normal. In the MINI Cooper S, the coolant pump may continue to run for some time after the engine is switched off. This will generate noise in the engine compartment.
85
Cargo loading
To avoid loading the tires beyond their approved carrying capacity, never over- load the vehicle. Overloading can lead to over- heating and increases the rate at which damage develops inside the tires. The ultimate result can assume the form of a sudden blowout.<
Avoid fluid spills in the cargo bay as they could damage the vehicle.<
Cargo bay cover
Do not place any objects on the cover; otherwise, they could endanger the car's occupants, e.g. in the case of braking or sudden swerving, or they may damage the cover.< The cargo bay cover can be locked in intermedi- ate positions 1 to 3.
To load bulky luggage, the cover can be removed. 1. Pull on the handle, arrow 1, to detach the
cargo bay cover.
Expanding the cargo bay The rear set backrest is split. Both sides can be folded separately to expand the cargo bay. If necessary, remove the third head restraint, refer to Head restraints, Removing page 31.
By way of example, the illustration shows the cargo compartment in the MINI. 1. Pull the lever. 2. Fold rear seat backrests forward.
When folding the backrest back up, make sure that the seat's locking mechanisms
engage properly. Otherwise, cargo could be thrown around in the event of sharp braking or swerving and endanger the occupants.<
Adjusting rear seat backrest* Expand the cargo bay by raising the split rear seat backrests to a steeper angle.
2. Lift the cargo bay cover up out of the hold-
backrest forward.
By way of example, the illustration shows the cargo compartment in the MINI. 1. Pull the lever, arrow 1, and fold the rear seat
ers, arrows 2.
86
2. Fold up the lever of the backrest lock until it
audibly engages, arrow 2.
3. Fold back the backrest until it engages.
If the rear seat backrests are positioned at a steeper angle, do not install child-
3. Fold up the eyelets on the rear seat and
hook the partition net into them, arrow 2.
restraint systems in the rear of the vehicle as their protective features may be ineffective.<
Level load floor*
The maximum load of the level load floor is 165 lbs/75 kg. Do not exceed a maxi- mum permissible load of 55 lbs/25 kg for the storage compartment beneath the level load floor; otherwise, damage can occur.<
Partition net*
Ensure that the partition net is firmly attached; otherwise, injuries may occur.< The partition net can be mounted in the cargo bay or behind the front seats.
In the cargo bay 1. Fold the rear seat backrest forward if neces-
sary, page 86.
Raise the level load floor and fold it up toward the front, arrow.
Removing 1. Fold up the level load floor. 2. Pull the load floor back slightly. 3. Then take it out toward the top.
Determining cargo limit
2.
Insert each partition net mounting pin all the way into its respective rear mount in the headliner, arrow 1, and push it forward.
3. Hang the hooks of the partition net into the
eyelets on the cargo bay floor, arrow 2.
Behind the front seats
1. Fold down the rear seat backrests, refer to
2.
Expanding the cargo bay. Insert each partition net mounting pin all the way into its respective front mount in the headliner, arrow 1, and push it forward.
1. Locate the following statement on your
vehicle's placard*:
The combined weight of occupants and cargo should never exceed
XXX kg or YYY lbs. Otherwise, the vehicle may be damaged and unstable driving con- ditions may result.<
87
2. Determine the combined weight of the
driver and passengers that will be riding in your vehicle.
3. Subtract the combined weight of the driver and passengers from XXX kilograms or YYY pounds.
4. The resulting figure equals the available
amount of cargo and luggage load capacity. For example, if the XXX amount equals 1,400 lbs and there will be four 150 lbs pas- sengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs: 1,400 lbs minus 750 lbs = 650 lbs.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. If your vehicle will be towing a trailer, part of the load from your trailer will be transferred to your vehicle. Consult the manual for transporting a trailer to determine how this may reduce the available cargo and luggage load capacity of your vehicle.
6.
Load
The permissible load is the sum of the occu- pants' weights and the weight of the cargo. The greater the weight of the occupants, the less cargo/luggage can be transported.
Stowing cargo > Position heavy objects as low and as far for- ward as possible, ideally directly behind the rear seat backrests.
> Cover sharp edges and corners.
88
> For very heavy cargo when the rear seat is not occupied, secure each safety belt in the respective opposite buckle.
> Do not stack higher than the top edge of the
backrests.
> Use the partition net, refer to page 87.
Ensure that no objects can penetrate through the net.
Securing cargo
By way of example, the illustration shows the cargo compartment in the MINI. > Secure smaller and lighter items using
retaining or draw straps*.
> Heavy-duty cargo straps* for securing larger
and heavier objects are available at your MINI dealer. Four lashing eyes are provided for attaching the cargo straps. Two of them are located on the forward wall of the cargo bay. Comply with the information enclosed with the load-securing devices.
Always position and secure the cargo as described above, so that it cannot endan- ger the car's occupants, for example if sudden braking or swerves are necessary. Do not exceed the approved gross weight and axle loads, page 144; otherwise, the vehicle's
operating safety is no longer assured and the vehicle will not be in compliance with the certifi- cation regulations. Heavy or hard objects should not be carried loose inside the car, since they could be thrown around, for example as a result of heavy braking, sudden swerves, etc., and endanger the occu- pants. Do not secure cargo using the fastening points for the tether strap, page 36; they may become damaged.<
The roof load must be distributed uniformly and should not be too large in area. Heavy items should always be placed at the bottom. When loading, make sure that there is sufficient space for the movement of the glass sunroof. Fasten roof-mounted cargo correctly and securely to prevent it from shifting or falling off during the trip. Drive smoothly. Avoid sudden acceleration and braking maneuvers, and take corners gently.
Roof-mounted luggage rack* A special rack system is available as an option for your MINI. Your MINI dealer will be glad to advise you. Comply with the installation instruc- tions supplied with the rack system.
Mounting points
By way of example, the illustration shows the roof of the MINI. Remove the cover panel.
Loading roof-mounted luggage rack Because roof racks raise the vehicle's center of gravity when loaded, they have a major effect on vehicle handling and steering response. You should therefore always remember not to exceed the approved roof load capacity, the approved gross vehicle weight or the axle loads when loading the rack. You can find the applicable data under Weights on page 144.
Saving fuel Fuel consumption depends on a number of dif- ferent factors. The implementation of certain measures, your driving style and regular mainte- nance can have an influence on fuel consump- tion and on the environmental impact.
Remove unnecessary cargo Additional weight increases fuel consumption.
Remove attached parts no longer in use Remove auxiliary mirrors, roof- or rear-mounted luggage racks whenever you are not using them. Attached parts on the vehicle affect its aerody- namics and increase fuel consumption.
Check tire inflation pressure regularly Check and, if necessary, correct tire inflation pressure at least twice a month and before start- ing on a long trip. Low inflation pressure increases rolling resis- tance and thus leads to greater fuel consump- tion and tire wear.
Drive off immediately Do not wait for the engine to warm up while the vehicle remains stationary. Start driving right away, but at moderate engine speeds. This is the fastest way for the cold engine to reach its oper- ating temperature.
89
Think ahead while driving Avoid unnecessary acceleration and braking by maintaining a suitable distance to the vehicle driving ahead. Driving smoothly and anticipating impending traffic situations reduces fuel consumption.
Avoid high engine speeds Use first gear only for driving off. In second and higher gears, accelerate smoothly to a suitable engine and road speed. In doing so, avoid high engine speeds and shift up early. When you reach your desired traveling speed, shift to the highest suitable gear and drive at constant speed. As a rule: driving at low engine speeds lowers fuel consumption and reduces wear.
Coasting When approaching a red traffic light, take your foot off the accelerator and let the vehicle coast to a halt in the highest suitable gear. On a downhill gradient, take your foot off the accelerator and let the vehicle coast in a suitable gear. Fuel supply is shut off automatically when the vehicle is coasting.
Switch off the engine during lengthy stops Switch off the engine when stopping for lengthy periods, e.g. at traffic lights, railroad crossings or in traffic jams.
Have the vehicle serviced Have your vehicle serviced regularly to achieve good economy and a long vehicle life. The man- ufacturer of your MINI recommends having the vehicle serviced by a MINI dealer. Also note the MINI Maintenance System, page 108.
90
E
91
AT A GLANCE
CONTROLS
DRIVING TIPS
MOBILITY
MOBILITY
REFERENCE
g
Refueling
Switch off the engine before refueling; otherwise, fuel cannot be added to the
tank and a message will be displayed.<
Take all precautionary measures and observe all applicable regulations when handling fuel. Do not carry any spare fuel con- tainers in your vehicle. They can develop a leak and cause an explosion or cause a fire in the event of an accident.<
Fuel filler flap
Opening
1. Open the fuel filler flap. 2. Turn the gas cap counterclockwise. 3. Place the gas cap in the bracket attached to
the fuel filler flap.
Closing Fit the cap and turn it clockwise until you clearly hear a click.
Do not pinch the band attached to the cap; otherwise, the cap cannot be closed properly and fuel vapors can escape. A message will be displayed if the gas cap is loose or miss- ing.<
94
Manually releasing the fuel filler flap In the event of an electrical malfunction, you can manually unlock the fuel filler flap:
Pull on the green knob with the fuel pump sym- bol; the fuel filler flap opens.
Observe the following when refueling
Take all precautionary measures and observe all applicable regulations when handling fuel; otherwise, there is a danger of personal injury and property damage.< When refueling, insert the filler nozzle com- pletely into the filler pipe. Avoid lifting the filler nozzle while filling the tank, as that would lead to > premature pump shutoff > reduced efficiency of the fuel-vapor recov-
ery system.
The fuel tank is full when the filler nozzle clicks off the first time.
Fuel tank capacity
If the range displayed is less than 30 miles/50 km, be sure to refuel; other- wise, engine functions are not guaranteed and damage could occur.< Approx. 13.2 US gallons/50 liters, including the reserve capacity of 2.1 US gallons/8 liters.
Fuel specifications
Do not use leaded gasoline; otherwise, permanent damage to the catalytic con-
verter will result. Do not fill the tank with E85, i.e. fuel containing 85% ethanol, nor with FlexFuel. Otherwise, the engine and fuel supply system will be dam- aged.<
Required fuel
Super Premium gasoline/AKI 91
This gasoline is highly recommended. However, you may also use gasoline with less AKI. The minimum AKI Rating is: > Cooper S, John Cooper Works: 89
> Cooper: 87
If you use gasoline with this minimum AKI Rat- ing, the engine may produce knocking sounds when starting at high outside temperatures. This has no effect on the engine life.Do not use any gasoline below the speci- fied minimum fuel grade. Otherwise, the
engine could be damaged.<
Use high-quality brands Field experience has indicated significant differ- ences in fuel quality: volatility, composition, additives, etc., among gasolines offered for sale in the United States and Canada. Fuels contain- ing up to and including 10% ethanol or other oxygenates with up to 2.8% oxygen by weight, that is, 15% MTBE or 3% methanol plus an equivalent amount of co-solvent, will not void the applicable warranties with respect to defects in materials or workmanship.
The use of poor-quality fuels may result in drivability, starting and stalling problems especially under certain environmental condi- tions such as high ambient temperature and high altitude. Should you encounter drivability problems which you suspect could be related to the fuel you are using, we recommend that you respond by switching to a recognized high-quality brand
such as gasoline that is advertised as Top Tier Detergent Gasoline. Failure to comply with these recommendations may also result in unscheduled maintenance.<
95
Wheels and tires
Tire inflation pressures
Information for your safety It is not merely the tires' service life, but also driving comfort and, to a great extent, driving safety that depend on the condition of the tires and the maintenance of the specified tire pres- sure.
Checking pressure
Check the tire inflation pressure regularly and correct it, if necessary: at least twice a month and before starting long trips. If you fail to observe this precaution you may be driving on tires with incorrect tire pressures, a condition that can not only compromise your vehicle's driving stability, but also lead to tire damage and the risk of an accident. Do not drive with deflated, i.e. flat tires, except when using run- flat tires. A flat tire will seriously impair your vehicle's handling and braking response. Attempts to drive on a flat tire can lead to loss of control over the vehicle.< Check the tire inflation pressures only on cold tires. This means after a maximum of 1.25 miles/ 2 km driving or when the vehicle has been parked for at least 2 hours. When tires are warm, the tire inflation pressure is higher.
After adjusting the tire inflation pressure, reinitialize the flat tire monitor, page 59,
or reset the Tire Pressure Monitor, page 61.<
Checking the tire inflation pressure of the compact tire* To check the inflation pressure, fold up the level load floor. Remove the onboard vehicle tool kit and the space-saver spare tire, refer to page 121.
Inflation pressure specifications The tables below provide all the correct inflation pressures for the specified tire sizes at ambient temperature.
96
The tire inflation pressures apply to the tire sizes approved and the tire brands recommended by the manufacturer of your MINI. Your MINI dealer will be glad to advise you.< For correct identification of the right tire infla- tion pressures, observe the following: > Tire sizes for your vehicle > Load conditions > Maximum allowable driving speed
Tire inflation pressures for driving up to 100 mph or 160 km/h For normal driving up to 100 mph or 160 km/h and to achieve optimum driving comfort, adjust pressures to the respective tire inflation pres- sures listed on the following pages in the col- umns for traveling speeds up to a maximum of 100 mph or 160 km/h. These tire inflation pressures can also be found on the driver's side door post when the driver's door is open.
The maximum permitted speed for these tire inflation pressures is 100 mph or
160 km/h. Do not exceed this speed; otherwise, tire damage and accidents may occur.<
Tire inflation pressures for driving above 100 mph or 160 km/h
In order to drive at maximum speeds in excess of 100 mph or 160 km/h, adjust pressures to the respective tire inflation pres- sures listed on the following pages in the col-
umns for traveling speeds including those exceeding 100 mph or 160 km/h. Otherwise, tire damage and accidents could occur.< Observe all national and local maximum speed limits; otherwise, violations of the law could occur.
97
MINI Cooper Clubman tire inflation pressures
Tire size
Pressure specifications in psi/kPa
Speeds up to a
max. of
100 mph/160 km/h
Speeds including those exceeding 100 mph/160 km/h
All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature
195/55 R 16 87 H 195/55 R 16 87 H RSC 195/55 R 16 87 H M+S RSC 195/55 R 16 87 V M+S RSC
175/65 R 15 84 T M+S 175/65 R 15 84 H M+S 175/65 R 15 84 H 175/60 R 16 82 H M+S RSC 205/45 R 17 84 V RSC 205/45 R 17 84 V M+S RSC 205/40 R 18 82 W RSC
Emergency wheel: 115/ 70 R 15 90 M
32/220
32/220
35/240
38/260
35/240
35/240
38/260
41/280
60/420
60/420
60/420
60/420
More details on the permissible load and weights can be found on page 144.
98
MINI Cooper S Clubman tire inflation pressures
Tire size
Pressure specifications in psi/kPa
Speeds up to a
max. of
100 mph/160 km/h
Speeds including those exceeding 100 mph/160 km/h
All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature
195/55 R 16 87 V RSC 195/55 R 16 87 H M+S RSC 195/55 R 16 87 V M+S RSC
205/45 R 17 84 V RSC 205/45 R 17 84 V M+S RSC 205/40 R 18 82 W RSC 175/60 R 16 82 H M+S RSC
35/240
35/240
38/260
41/280
38/260
38/260
41/280
44/300
More details on the permissible load and weights can be found on page 144.
99
MINI John Cooper Works Clubman tire inflation pressures
Tire size
Pressure specifications in psi/kPa
Speeds up to a
max. of
100 mph/160 km/h
Speeds including those exceeding 100 mph/160 km/h
All pressure specifications in the table are indicated in psi/kilopascal with cold tires. Cold = ambient temperature
185/50 R 17 86 H M+S XL RSC 205/45 R 17 84 V M+S RSC 205/45 R 17 84 W RSC
38/260
38/260
39/270
45/310
205/40 R 18 82 W RSC
41/280
41/280
42/290
48/330
More details on the permissible load and weights can be found on page 144.
100
Tire coding Knowledge of the labeling on the side of the tire makes it easier to identify and choose the right tires.
Tire size
Speed code letter Q = up to 100 mph or 160 km/h T = up to 118 mph or 190 km/h H = up to 131 mph or 210 km/h V = up to 150 mph or 240 km/h W = up to 167 mph or 270 km/h Y = up to 186 mph or 300 km/h
Tire Identification Number Tires with DOT codes meet the guidelines of the US Department of Transportation. DOT code:
DOT xxxx xxx 0810
Uniform Tire Quality Grading For instance: Manufacturer's code for tire make Tire size and tire design Tire age Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Tread wear 200 Traction AA Temperature A
DOT Quality Grades Tread wear Traction AA A B C Temperature A B C
All passenger car tires must conform to Federal Safety Requirements in addition
to these grades.<
Tread wear The tread wear grade is a comparative rating based on the wear rate of the tire when tested
under controlled conditions on a specified gov- ernment test course. For example, a tire graded 150 would wear one and one-half (1γ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, how- ever, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
Traction The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test sur- faces of asphalt and concrete. A tire marked C may have poor traction performance.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, corner- ing, hydroplaning, or peak traction characteris- tics.<
Temperature The temperature grades are A, the highest, B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sus- tained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent lev- els of performance on the laboratory test wheel that exceed the minimum required by law. The temperature grade for this tire is established for a tire that is properly
inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure.<
101
RSC - run-flat tires* You will recognize run-flat tires by a circular symbol containing the letters RSC on the side of the tire, page 103.
M+S Winter and all-season tires. These have better winter properties than sum- mer tires.
XL Designation for specially reinforced tires.
Tire condition Inspect your tires regularly for tread wear, signs of damage and for foreign objects lodged in the tread. Check the tread depth.
Tread depth The tread depth should not drop below 1/8 in/ 3 mm, although, for example, European legisla- tion only specifies a minimum tread depth of 1/16 in/1.6 mm. At tread depths below 1/8 in/ 3 mm there is an increased risk of high-speed hydroplaning, even when only small amounts of water are present on the road surface.
Winter tires When winter tires wear down past a tread depth of 1/6 in/4 mm, they become perceptibly less suitable for winter conditions. In the interest of safety, new tires should be installed.
Minimum tread depth
the letters TWI, for Tread Wear Indicator, on the tire's sidewalls identify tires that incorporate these wear indicators. When tire tread is worn down to the level of the wear indicators, the remaining tread depth is 1/16 in/1.6 mm.
Tire damage Due to low-profile tires, please note that wheels, tires and suspensions parts are more susceptible to road hazards and consequential damages. Unusual vibrations encountered during normal vehicle operation can indicate tire failure or some other vehicle defect. This can, for exam- ple, be caused by driving over curbs. The same applies to any other abnormal road behavior, such as pulling severely to the right or left.
In these cases, reduce speed immediately and have wheels and tires thoroughly
checked. To do so, drive carefully to the nearest MINI dealer or tire shop that works according to MINI repair procedures with correspondingly trained personnel. If necessary, have the vehicle towed there. Otherwise, tire damage can be extremely dan- gerous for vehicle occupants and other road users.<
Tire age The manufacturing date of tires is contained in the tire coding: DOT ... 0810 means that the tire was manufac- tured in week 8 of 2010. For various reasons, such as the development of brittleness, the manufacturer of your MINI rec- ommends tire replacement after no more than 6 years, regardless of the actual wear of the tires.
Wear indicators in the base of the tread groove are distributed around the tire's circumference;
102
Run-flat tires*
The symbol identifying run-flat tires is a circle with the letters RSC on the sidewall. Run-flat tires comprise a conditionally self-sup- porting tire and a special rim. The reinforcement in the sidewalls ensures that the tire can con- tinue to be used subject to certain restrictions, even if depressurized. For information on continuing to drive with a flat tire, refer to Indication of a flat tire, page 60.
New wheels and tires
Have new wheels and tires mounted only by your MINI dealer or a specialized tire shop that has specially trained personnel work- ing in accordance with the specifications of the MINI manufacturer. If this work is not carried out properly, there is a danger of subsequent dam- age and related safety hazards. Make sure that the new wheels are balanced.<
Retreaded tires
The manufacturer of your MINI recom- mends that you avoid using retreaded tires, as this could impair driving safety. The causes for this include potentially different tire casing structures and often wide variations in tire age, which can result in a limited service life.<
Correct wheels and tires
The manufacturer of your MINI recom- mends mounting only wheels and tires
that it has specifically approved for use on your
