2010 Mercedes-benz M Class Owners Manual

X Open the front passenger door. X Opening: Open the glove box. X Opening: Insert flat, blunt object as a lever into the edge of fuse box cover : at the position indicated by the arrow.

X Loosen fuse box cover : from the

dashboard using the lever.

X Using your hands, pull fuse box cover :

out and remove.

X Closing: Hook fuse box cover : into holders on the front of the dashboard. X Press fuse box cover : back on until it

engages.

! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

Fuse box in engine compartment X Open the hood.

164_AKB; 7; 31, en-US d2ureepe,

344 Fuses

2009-09-11T12:07:36+02:00 - Seite 344
Version: 2.11.8.1

X Opening: Open the cargo compartment. X Insert a suitable object such as a coin into

the slot of lock :.

X Turn lock : by 90° in direction of arrow. X Remove cover ;. X Closing: Install everything in reverse order.

Emergency engine shutdown If the engine cannot be turned off as described (Y page 108), you may use the following emergency procedure. X Take the fuse chart from the vehicle tool kit

(Y page 268).

X Open the fuse box in engine compartment. X Remove fuse 120.

Find its location in the fuse chart.

Example illustration fuse box ML 350 (ML 350
BlueTEC, ML 550, ML 63 AMG similar) X With a dry cloth, remove any moisture from

fuse box cover :.

X Opening: Pull clamps ; in direction of

arrow.

X Lift fuse box cover : up. X Closing: Make sure the sealing rubber is

positioned properly.

X Press fuse box cover : down and secure

with clamps ;.

! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

X Close the hood after checking or replacing

fuses.

Fuse box in cargo compartment

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 345
Version: 2.11.8.1

Vehicle equipment ............................ 346
Parts service ..................................... 346
Warranty coverage ........................... 346
Identification labels .......................... 346
Vehicle specification ML 350 Blue- TEC 4MATIC (164.125) ..................... 348
Vehicle specification ML 350
(164.156) ........................................... 348
Vehicle specification ML 350
4MATIC (164.186) ............................. 349
Vehicle specification ML 550
4MATIC (164.172) ............................. 350
Vehicle specification ML 63 AMG (164.177) ........................................... 351
Rims and tires ................................... 352
Fuels, coolants, lubricants, etc. ...... 356

345

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 346
Version: 2.11.8.1

346

Identification labels

accordance with the terms of the following warranties: RNew Vehicle Limited Warranty REmission System Warranty REmission Performance Warranty RCalifornia, Connecticut, Maine,

Massachusetts, New York, Pennsylvania, Rhode Island, and Vermont Emission Control Systems Warranty33

RState Warranty Enforcement Laws (Lemon

Laws)

Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center.

Loss of Service and Warranty Information booklet Should you lose your Service and Warranty Information booklet, have an authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.

Identification labels

Vehicle equipment

i This Operator’s Manual describes all

features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.

Parts service

All authorized Mercedes-Benz Centers maintain a stock of Genuine Mercedes-Benz Parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different parts for Mercedes-Benz models are available. Genuine Mercedes-Benz Parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Genuine Mercedes-Benz Parts should be installed. ! Do not use non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz. Doing so could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty. Also, it could compromise the vehicle’s durability or safety.

Warranty coverage

Your vehicle is covered under the terms of the warranties printed in the Service and Warranty Information booklet. Your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed in the vehicle in

33 Applicable to vehicles with gasoline engine only.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 347
Version: 2.11.8.1

Identification labels

347

data shown in the illustration. Refer to certification label on vehicle for actual data specific to your vehicle.

The Vehicle Identification Number (VIN) can be found Ron certification label : on the driver’s door

B-pillar

Ron passenger side underneath the rear seat

(Y page 347)

Ron the lower edge of the windshield

(Y page 347)

Passenger-side rear seat X Fold seat cushion ? forward

(Y page 189).

X Fold carpet A forward in direction of

arrow. VIN B is now visible.

Example certification label (U.S. vehicles) ; Paintwork code = VIN

Example certification label (Canada vehicles) ; Paintwork code = VIN

i Data shown on certification label are for illustration purposes only. These data are specific to each vehicle and may vary from

C Emission control information label, includes both federal and California certification exhaust emission standards

D Engine number (engraved on engine) E VIN (on lower edge of windshield)

i When ordering parts, please specify

vehicle identification and engine number.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 348
Version: 2.11.8.1

348 Vehicle specification ML 350 (164.156)

Vehicle specification ML 350 BlueTEC 4MATIC (164.125)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. Engine ΜL 350 BlueTEC 4MATIC

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 1349
Maximum torque acc. to SAE J 1349

642

Diesel 4-stroke

engine

3.27 in (83.00 mm) 3.62 in (92.00 mm)

182.3 cu in (2 987 cm3)

16.5:1

210 hp/3 400 rpm (157 kW/3 400 rpm)

400 lb-ft/

1 600 - 2 400 rpm

(543 Nm/

1 600 - 2 400 rpm)

Maximum engine speed Firing order Poly-V-belt

4 500 rpm

1-4-2-5-3-6
2 035 mm

Electrical system

ΜL 350 BlueTEC 4MATIC

Alternator Starter motor Battery

14 V/220 A 12 V/2.0 kW 12 V/95 Ah

Main dimensions

ΜL 350 BlueTEC 4MATIC

188.5 in (4 788 mm)

83.6 in (2 124 mm)

Overall vehicle length Overall vehicle width34
Overall vehicle height

71.5 in (1 815 mm)35
69.8 - 73.0 in (1 774 - 1 854 mm)36
Wheelbase 114.8 in (2 915 mm) Track, front 63.7 in (1 619 mm) Track, rear 63.8 in (1 621 mm) Ground clearance 8.3 in (210 mm)35

7.3 - 10.3 in (186 - 261 mm)36
39.0 ft (11.6 m)

Turning circle

Weights ΜL 350 BlueTEC 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 350 (164.156)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ΜL 350

Engine, type Mode of operation

272

4-stroke engine, gasoline injection

No. of cylinders

34 Exterior rear view mirrors folded out. 35 Vehicles with steel suspension. 36 Depending on the set vehicle level (vehicles with air suspension program).

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 349
Version: 2.11.8.1

Vehicle specification ML 350 4MATIC (164.186)

349

Engine ΜL 350

Main dimensions ΜL 350

Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134937
Maximum torque acc. to SAE J 1349

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

10.7:1

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 398 mm

Electrical system ML 350

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

14 V/180 A 12 V/1.4 kW 12 V/70 Ah

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)

188.5 in (4 788 mm)

Overall vehicle length Overall vehicle width38
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 8.3 in (210 mm) Turning circle 39.0 ft (11.6 m)

114.8 in (2 915 mm) 64.0 in (1 627 mm) 64.1 in (1 629 mm)

Weights ΜL 350

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 350 4MATIC (164.186)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ΜL 350 4MATIC 272

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement

4-stroke engine, gasoline injection

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

37 Premium fuel required. Performance may vary with fuel octane rating. 38 Exterior rear view mirrors folded out.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 350
Version: 2.11.8.1

350 Vehicle specification ML 550 4MATIC (164.172)

Engine ΜL 350 4MATIC 10.7:1

Compression ratio Output acc. to SAE J 134939
Maximum torque acc. to SAE J 1349

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 398 mm

Electrical system ML 350 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/70 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions ΜL 350 4MATIC

Wheelbase 114.8 in (2 915 mm) Track, front 64.0 in (1 627 mm) Track, rear 64.1 in (1 629 mm) Ground clearance 8.3 in (210 mm)41

7.3 - 10.3 in (186 - 261 mm)42
39.0 ft (11.6 m)

Turning circle

Weights ΜL 350 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 550 4MATIC (164.172)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ML 550 4MATIC 273

Engine, type Mode of operation

4-stroke engine, gasoline injection

3.86 in (98.00 mm) 3.56 in (90.50 mm)

333.2 cu in (5 461 cm3)

10.7:1

Main dimensions ΜL 350 4MATIC

Overall vehicle length Overall vehicle width40
Overall vehicle height

188.5 in (4 788 mm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)41
69.8 - 73.0 in (1 774 - 1 854 mm)42

No. of cylinders Bore Stroke Total piston displacement Compression ratio

39 Premium fuel required. Performance may vary with fuel octane rating. 40 Exterior rear view mirrors folded out. 41 Vehicles with steel suspension. 42 Depending on the set vehicle level (vehicles with air suspension program).

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 351
Version: 2.11.8.1

Vehicle specification ML 63 AMG (164.177)

351

Main dimensions ΜL 550 4MATIC Track, front 63.7 in (1 619 mm) Track, rear 63.8 in (1 621 mm) Ground clearance 8.3 in (210 mm)45

7.3 - 10.3 in (186 - 261 mm)46
39.0 ft (11.6 m)

6 500 rpm

Turning circle

1-5-4-2-6-3-7-8

2 398 mm

Weights ΜL 550 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 63 AMG (164.177)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ML 63 AMG

Engine ML 550 4MATIC

382 hp/6 000 rpm (285 kW/6 000 rpm)

391 lb-ft/

2 800 - 4 800 rpm

(530 Nm/

2 800 - 4 800 rpm)

Output acc. to SAE J 134943
Maximum torque acc. to SAE J 1349

Maximum engine speed Firing order Poly-V-belt

Electrical system ML 550 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/95 Ah NGK PLKR 7A

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Engine, type Mode of operation

Main dimensions ΜL 550 4MATIC

Overall vehicle length Overall vehicle width44
Overall vehicle height

Wheelbase

188.5 in (4 788 mm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)45
69.8 - 73.0 in (1 774 - 1 854 mm)46
114.8 in (2 915 mm)

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134947

43 Premium fuel required. Performance may vary with fuel octane rating. 44 Exterior rear view mirrors folded out. 45 Vehicles with steel suspension. 46 Depending on the set vehicle level (vehicles with air suspension program). 47 Premium fuel required. Performance may vary with fuel octane rating.

156

4-stroke engine, gasoline injection

4.02 in (102.20 mm) 3.72 in (94.60 mm)

378.8 cu in (6 208 cm3)

11.3:1

503 hp/6 800 rpm (375 kW/6 800 rpm)

164_AKB; 7; 31, en-US d2ureepe,

352 Rims and tires

2009-09-11T12:07:36+02:00 - Seite 352
Version: 2.11.8.1

Engine ML 63 AMG

Weights ML 63 AMG

Maximum torque acc. to SAE J 1349
Maximum engine speed Firing order Poly-V-belt

465 lb-ft/5 200 rpm (630 Nm/5 200 rpm)

7 200 rpm

1-5-4-2-6-3-7-8

2 360 mm

Electrical system ML 63 AMG 14 V/180 A 12 V/2.1 kW 12 V/95 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

NGK ILZKAR 7A10
0.039 in (1.0 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions ML 63 AMG

83.6 in (2 124 mm)

189.7 in (4 818 mm)

Overall vehicle length Overall vehicle width48
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 7.0 - 10.1 in

69.5 - 72.6 in (1 765 - 1 845 mm)49
114.8 in (2 915 mm) 65.5 in (1 664 mm) 65.6 in (1 667 mm)

Turning circle

(177 - 257 mm)49
39.0 ft (11.6 m)

48 Exterior rear view mirrors folded out. 49 Depending on the set vehicle level.

Roof load

max. 220 lb (100 kg)

Rims and tires Notes ! Only use tires which have been tested and

approved by Mercedes-Benz. Tires approved by Mercedes-Benz are developed to provide best possible performance in conjunction with the driving safety systems on your vehicle such as the ABS or the ESP®. Tires specially developed for your vehicle and tested and approved by Mercedes-Benz can be identified by finding the following on the tire’s sidewall: RMO = Mercedes-Benz Original

equipment tires

RMOE = Mercedes-Benz Original Extended

(tires with limited run-flat characteristics) original equipment tires Using tires other than those approved by Mercedes-Benz may result in damage that is not covered by the Mercedes-Benz Limited Warranty.

For information on driving with MOExtended tires, see the “Practical hints” section (Y page 330). i Vehicles with MOExtended system are not factory-equipped with a TIREFIT kit. When retrofitting with tires that do not have run-flat characteristics, you should also equip your vehicle with a TIREFIT kit. TIREFIT kits are available at any authorized Mercedes-Benz Center.

! Using tires other than those approved by

Mercedes-Benz can have detrimental effects, such as

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 353
Version: 2.11.8.1

Rpoor handling characteristics Rincreased noise Rincreased fuel consumption Moreover, tires and rims not approved by Mercedes-Benz may, under load, exhibit dimensional variations and different tire deformation characteristics that could cause them to come into contact with the vehicle body or axle parts. Damage to the tires or the vehicle may be the result.

i Further information on tires and rims is

available at any authorized Mercedes-Benz Center. The Tire and Loading Information placard with the recommended tire inflation pressures for cold tires is located on the driver’s door B-pillar. Supplemental tire inflation pressure information for driving at high speeds or for vehicle loads less than the maximum loaded vehicle condition can be found on the tire inflation pressure label. The tire inflation pressure label is located on the inside of the fuel filler flap. The tire inflation pressure should be checked regularly and should only be adjusted on cold tires. Follow tire manufacturer’s maintenance recommendation included with the vehicle.

For information on recommended tire inflation pressure and supplemental tire inflation pressure information for special driving situations, see (Y page 219). i Please keep in mind that the vehicle must

be equipped Rwith wheels of identical dimensions on

each axle (left and right)

Rwith tires of identical characteristics all around, i.e. summer tires, winter tires, all-season tires, or MOExtended tires etc.

i The following pages also list the approved rim and tire sizes for equipping your vehicle with winter tires. Winter tires are not available as standard or optional factory

Rims and tires

353

equipment, but can be purchased from an authorized Mercedes-Benz Center. Equipping your vehicle with winter tires approved for your vehicle model may require the purchase of rims of the recommended size for use with these winter tires. This depends on vehicle model and the standard or optional factory- equipped wheel rim/tire configuration on your vehicle. For more information contact an authorized Mercedes-Benz Center.

164_AKB; 7; 31, en-US d2ureepe,

354 Rims and tires

Same size tires

Model

18" wheels Rims (light alloy)

Wheel offset Winter tires50,51,52
All-terrain tires50,51,52

Model

19" wheels Rims (light alloy)

Wheel offset All-season tires50
Winter tires50,51

Model

19" wheels Rims (light alloy)

Wheel offset All-season tires50

Winter tires50,51

2009-09-11T12:07:36+02:00 - Seite 354
Version: 2.11.8.1

ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 350 4MATIC (Sport Package) ML 550 4MATIC 8 J x 18 H2
2.36 in (60 mm) 255/55 R18 105H M+Si 255/55 R18 105H M+S

ML 350
ML 350 4MATIC ML 350 BlueTEC 4MATIC53
8 J x 19 H2
2.36 in (60 mm) 255/50 R19 107H XL (Extra Load) M+S 255/50 R19 107H XL (Extra Load) M+Si

ML 350 BlueTEC 4MATIC53
8 J x 19 H2
2.36 in (60 mm) 255/50 R19 107H XL (Extra Load) M+S MOExtended54
255/50 R19 107H XL (Extra Load) M+Si MOExtended54

50 Radial-ply tires. 51 Not available as factory equipment. 52 ML 350 BlueTEC 4MATIC: Standard tire without run-flat characteristics. Equipping the vehicle with TIREFIT

is strongly recommended.

53 ML 350 BlueTEC: Availabilty in Canada depending on vehicle production date. 54 Must be used in conjunction with Advanced Tire Pressure Monitoring System (U.S. vehicles) or tire pressure

loss warning system (Canada vehicles) only.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 355
Version: 2.11.8.1

Rims and tires

355

19"wheels

Model AMG rims (light alloy) Wheel offset All-season tires55
Winter tires55,56

ML 550 4MATIC (Sport Package) 8.5 J x 19 H2
2.28 in (58 mm) 255/50 R19 107H XL (Extra Load) M+S 255/50 R19 107H XL (Extra Load) M+Si

Model

19" wheels AMG rims (light alloy)

Wheel offset Winter tires55,56

ML 63 AMG 9.5 J x 19 H2
1.81 in (46 mm) 285/45 R19 107H M+Si

Model

20" wheels Rims (light alloy)

Wheel offset All-season tires55

ML 350 (Appearance Package) ML 350 4MATIC (Appearance Package) 8.5 J x 20 H2
2.17 in (55 mm) 265/45 R20 108H XL (Extra Load) M+S

Model

20" wheels AMG rims (light alloy)

Wheel offset All-season tires55,57

ML 550 4MATIC (Sport Package) 8.5 J x 20 H2
2.36 in (60 mm) 265/45 R20 108H XL (Extra Load) M+S

Model

20" wheels AMG rims (light alloy)

Wheel offset Summer tires55,57

ML 63 AMG 10 J x 20 H2
1.81 in (46 mm) 295/40 ZR20 106Y

Model

21" wheels AMG rims (light alloy)

Wheel offset Summer tires55,57

ML 63 AMG 10 J x 21 H2
1.81 in (46 mm) 295/35 ZR21 107Y XL (Extra Load)

55 Radial-ply tires. 56 Not available as factory equipment. 57 Must not be used with snow chains.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 356
Version: 2.11.8.1

356 Fuels, coolants, lubricants, etc.

Spare wheel

! Compare the recommended tire inflation pressure for your vehicle with the tire inflation

pressure on the yellow label located on the spare wheel rim. If the tire inflation pressure on the yellow label on the spare wheel rim differs from the values given in this Operator’s Manual, inflate the tire to the recommended tire inflation pressure given on the yellow label on the spare wheel rim.

i Please note that the tire inflation pressure of the spare wheel differs from the tire inflation

pressure of the road tires.

i The ML 350 BlueTEC 4MATIC does not have a spare wheel. Model

ML 63 AMG

Rim Wheel offset Minispare tire58

Collapsible tire58
Recommended tire inflation pressure

ML 350 (all models) ML 550 (all models) 4.0 B x 18 H2
1.58 in (40 mm) T 155/90 D18 113M or T 155/90 R18 113M — 61 psi (4.2 bar)

5.5 B x 19 H2
0.51 in (13 mm) —

185/85-19 104P 51 psi (3.5 bar)

fluids. Otherwise you could endanger persons or the environment. Keep service fluids out of the reach of children. For health reasons, you should prevent service fluids from coming into direct contact with your skin or clothing. If a service fluid is swallowed, contact a physician immediately.

Fuels, coolants, lubricants, etc. Capacities Vehicle components and their respective lubricants must match. Therefore only use products tested and approved by Mercedes- Benz. For information on tested and approved products, contact an authorized Mercedes- Benz Center or visit www.mbusa.com (USA only). G Warning! Comply with all valid regulations with respect to handling, storing, and disposing of service

58 Must not be used with snow chains.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 357
Version: 2.11.8.1

Fuels, coolants, lubricants, etc.

357

Engine with oil filter

Automatic transmission

Front axle

Rear axle

Transfer case

Model

Capacity

9.5 US qt (9.0 l) 10.3 US qt (9.7 l) 9.5 US qt (9.0 l)

ML 350 BlueTEC 4MATIC 9.0 US qt (8.5 l) ML 350 4MATIC 8.5 US qt (8.0 l) ML 350
ML 550 4MATIC ML 63 AMG59
All models, except ML 63 AMG ML 63 AMG60
ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 550 4MATIC ML 63 AMG

9.7 US qt (9.2 l) 1.2 US qt (1.1 l)

ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 550 4MATIC ML 350
ML 63 AMG

ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 550 4MATIC ML 63 AMG

Power steering ML 350

ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 550 4MATIC ML 63 AMG

59 Engine with oil cooler. 60 Automatic transmission with oil cooler.

1.2 US qt (1.1 l)

1.5 US qt (1.4 l) 1.2 US qt (1.1 l)

0.53 US qt (0.5 l)

approx. 1.3 US qt (1.2 l)

approx. 1.05 US qt (1.0 l)

approx. 1.3 US qt (1.2 l)

Fuels, coolants, lubricants, etc. Approved engine oils

MB Automatic Transmission Fluid

Hypoid gear oil

Fuchs Titan EG 5010 D Hypoid gear oil

Fuchs Titan EG 5010 D MB Automatic Transmission Fluid

MB Power Steering Fluid or approved Dexron III ATF MB Power Steering Fluid

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 358
Version: 2.11.8.1

358 Fuels, coolants, lubricants, etc.

Model

Capacity

Brake system

All models

0.63 US qt (0.6 l)

Cooling system ML 350 BlueTEC 4MATIC

ML 350 4MATIC ML 350
ML 550 4MATIC

ML 63 AMG

All models All models, except ML 63 AMG ML 63 AMG

Fuel tank Fuel tank reserve

approx. 10.0 US qt (9.5 l)

approx. 12.7 US qt (12.0 l) approx. 12.2 US qt (11.5 l) 25.1 US gal (95.0 l) approx. 3.4 US gal (13.0 l) approx. 4.0 US gal (15.0 l)

AdBlue® tank

ML 350 BlueTEC 4MATIC 7.0 US gal (26.6 l)

All models

—

All models

7.6 US qt (7.2 l)

Air conditioning system

Washer system and headlamp cleaning system

Fuels, coolants, lubricants, etc. MB Brake Fluid (DOT 4+) MB 325.0
Anticorrosion/ Antifreeze

Gasoline engine: Premium unleaded gasoline (Minimum Posted Octane 91
[Avg. of 96 RON/86 MON]) Diesel engine: ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL (ULSD, 15 ppm SULFUR MAXIMUM) AdBlue® complying with ISO 22241
R134a refrigerant and special PAG lubricant oil (never R 12) MB Windshield Washer Concentrate61
(Y page 364) Washer fluid mixing ratio (Y page 364)

61 Mixed with water or commercially available premixed washer solvent/antifreeze.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 359
Version: 2.11.8.1

Approved engine oils Engine oils are specifically tested for their suitability in our engines and durability for our service intervals. Therefore, only use approved engine oils and oil filters required for vehicles with the Maintenance System. For a listing of approved engine oils and oil filters, contact an authorized Mercedes-Benz Center or visit www.mbusa.com (USA only). ! Using engine oils and oil filters of a

specification other than those expressly required for the Maintenance System, or changing of oil and oil filter at change intervals longer than those called for by the Maintenance System will result in engine or emission control system damage not covered by the Mercedes-Benz Limited Warranty. Please follow Maintenance System recommendations for scheduled oil changes. Failure to do so will result in engine or emission control system damage not covered by the Mercedes-Benz Limited Warranty.

Mercedes-Benz recommends MOBIL OIL. Use the table below to determine the MB sheet number. Model

Engine, type 642

MB sheet number 229.51

ML 350 BlueTEC 4MATIC ML 350 4MATIC ML 350

ML 550 4MATIC ML 63 AMG

272
272

273
156

229.5
229.3/ 229.5
229.5
229.562

i MB sheet numbers are printed on the

outside of oil containers.

Fuels, coolants, lubricants, etc.

359

Viscosity grades for engine oils Using the chart below, select oil viscosity according to the lowest air temperature expected before the next oil change.

Engine oil additives ! Do not blend oil additives with engine oil. They may damage the engine. Damage or malfunctions resulting from blending oil additives are not covered by the Mercedes- Benz Limited Warranty.

Air conditioning refrigerant R134a (HFC) refrigerant and special PAG lubricating oil are used in the air conditioning system. ! Never use R 12 (CFC) or mineral-based lubricating oil. Otherwise damage to the system will occur.

Brake fluid G Warning! During vehicle operation, the boiling point of the brake fluid is continuously reduced through the absorption of moisture from the atmosphere. Under extremely strenuous operating conditions, this moisture content can lead to

62 Restriction: Only SAE 0W-40/SAE 5W-40 engine oils may be used.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 360
Version: 2.11.8.1

360 Fuels, coolants, lubricants, etc.

the formation of bubbles in the system, thus reducing the system’s efficiency. Therefore, the brake fluid must be replaced regularly. Refer to your vehicle’s Maintenance Booklet for replacement interval. Only brake fluid approved by Mercedes-Benz is recommended. Any authorized Mercedes- Benz Center will provide you with additional information.

Premium unleaded gasoline (gasoline engine) G Warning! Gasoline is highly flammable and poisonous. It burns violently and can cause serious personal injury. Never allow sparks, flames or smoking materials near gasoline! Turn off the engine before refueling. Whenever you are around gasoline, avoid inhaling fumes and any skin or clothing contact. Extinguish all smoking materials. Direct skin contact with fuels and the inhalation of fuel vapors are damaging your health.

! To maintain the engine’s durability and performance, premium unleaded gasoline must be used. If premium unleaded gasoline is not available and low octane gasoline is used, follow these precautions: RHave the fuel tank only partially filled

with unleaded regular gasoline and fill up with premium unleaded gasoline as soon as possible.

RAvoid full throttle driving and abrupt

acceleration.

RDo not exceed an engine speed of

3 000 rpm if the vehicle is loaded with a

light load such as two persons and no luggage.

RDo not exceed 2/3 of maximum

accelerator pedal position if the vehicle is fully loaded or operating in mountainous terrain.

Fuel requirements Gasoline engine Only use premium unleaded gasoline. The octane number (posted at the pump) must be 91 min. It is an average of both the Research Octane Number (RON) and the Motor Octane Number (MON): (RON+MON)/2. This is also known as the ANTI-KNOCK INDEX. Reformulated gasolines (RFG) and/or unleaded gasoline containing oxygenates such as ethanol, TAME, ETBE, IPA, IBA, and TBA can be used provided the ratio of any one of these oxygenates to gasoline does not exceed 10%; MTBE must not exceed 15%. The ratio of methanol to gasoline must not exceed 3% plus additional cosolvents. Using mixtures of ethanol and methanol is not allowed. Gasohol, which contains 10% ethanol and 90% unleaded gasoline, can be used. These blends must also meet all other fuel requirements, such as resistance to spark knock, boiling range, vapor pressure, etc.

Diesel engine Only use commercially available vehicular ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL (ULSD, 15 ppm SULFUR MAXIMUM) that meets the ASTM D975 standard. Failure to use ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL (ULSD) can severely damage the vehicle’s exhaust after-treatment device. To prevent malfunctions, diesel fuel with improved cold flow characteristics is offered in the winter months. Check with your fuel retailer.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 361
Version: 2.11.8.1

! Do not fill the tank with gasoline. Do not blend diesel fuel with gasoline or kerosene. The fuel system and engine will otherwise be damaged, which is not covered by the Mercedes-Benz Limited Warranty.

For further information on diesel fuel pump labeling, contact an authorized Mercedes- Benz Center or visit www.mbusa.com (USA only). Biodiesel (FAME = Fatty Acid Methyl Ester) containing fuels Mercedes-Benz USA approves the use of B5
(standard ULSD which may contain a maximum of 5% biodiesel) in all Common-rail injection (CDI) and BlueTEC diesel engines. Diesel fuels containing a higher percentage of biodiesel, e.g. B20, as well as straight biodiesel may cause severe damage to your engine/fuel system and are not approved. Please ask your service station personnel for further information. If the B5 biodiesel blend is not sufficiently labeled to clearly indicate that it meets the ULSD standard, please do not use it. The Mercedes-Benz Limited Warranty does not cover damages caused by the use of fuels not meeting Mercedes-Benz approved fuel standards.

Gasoline additives (gasoline engine) A major concern among engine manufacturers is carbon build-up caused by gasoline. Mercedes-Benz recommends only the use of quality gasoline containing additives that prevent the build-up of carbon deposits. After an extended period of using fuels without such additives carbon deposits can build up, especially on the intake valves and in the combustion area, leading to engine performance problems such as: RWarm-up hesitation RUnstable idle

Fuels, coolants, lubricants, etc.

361

RKnocking/pinging RMisfire RPower loss In areas where carbon deposits may be encountered due to lack of availability of gasoline which contains these additives, the use of Mercedes-Benz approved additives is recommended. Contact an authorized Mercedes-Benz Center or visit www.mbusa.com (USA only) for a listing of approved products. Follow directions on the product label. Do not blend other fuel additives with fuel. This only results in unnecessary cost and may be harmful to the engine operation. ! Damage or malfunction resulting from

poor fuel quality or from blending additional fuel additives other than those tested and approved by us for use on Mercedes-Benz vehicles are not covered by the Mercedes- Benz Limited Warranty or by any pre-owned or Extended Limited Warranties.

AdBlue® AdBlue® is a non-flammable, non-toxic, colorless and odorless, water-soluble liquid. ! Only use AdBlue® complying with

ISO 22241. Do not blend with additives.

! Rinse surfaces that have come into

contact with AdBlue®, or remove AdBlue® with a moist cloth and cold water immediately. If AdBlue® has crystallized already, use cold water and a sponge. AdBlue® residues will crystallize and soil the affected surfaces.

High ambient temperatures If AdBlue® in the reservoir heats up to above 122‡ (50†) for a long period of time, for example due to direct sunlight, ammonia gas

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 362
Version: 2.11.8.1

362 Fuels, coolants, lubricants, etc.

vapors may escape when opening the AdBlue® tank. G Warning! When opening the filler cap of the AdBlue® tank ammonia gas vapors may escape. Refill AdBlue® in a well ventilated area only. Ammonia gas vapors have a pungent odor and are particularly irritating for your skin, mucous membranes, and eyes. Inhaling ammonia gas vapors will cause burning eyes, nose, and throat, as well as coughing and watering eyes.

Low ambient temperatures AdBlue® freezes at a temperature of approximately 12‡ (-11†). Your vehicle is factory equipped with an AdBlue® preheating system. The vehicle can thus be operated at temperatures below 12‡ (-11†).

Special additives ! Only use AdBlue® complying with ISO 22241. Do not add additives to AdBlue® and do not dilute AdBlue® with water. Otherwise, the BlueTEC exhaust gas aftertreatment system could be damaged. Damage caused by using additives or diluting with water are not covered by the Mercedes-Benz Limited Warranty.

Purity The purity of AdBlue® is of particular importance for avoiding malfunctions in the exhaust gas aftertreatment. If AdBlue® is pumped out of the tank, e.g. during repair work, the same liquid must not be used to refill the tank as its purity is no longer guaranteed. ! Impurities caused for example by other

service products, cleaning agents, and dust result in increased emissions, malfunctions, catalyst damage, or engine damage.

Coolants The engine coolant is a mixture of water and anticorrosion/antifreeze, which provides: RCorrosion protection RFreeze protection RBoiling protection (by increasing the boiling

point)

The cooling system was filled at the factory with a coolant providing freeze protection to approximately -35‡ (-37†) and corrosion protection. ! Add premixed coolant solution only.

Adding water and MB 325.0 Anticorrosion/ Antifreeze separately from each other, could cause engine damage not covered by the Mercedes-Benz Limited Warranty.

If the antifreeze mixture is effective to -35‡ (-37†), the boiling point of the coolant in the pressurized cooling system is reached at approximately 266‡ (130†). The coolant solution must be used year round to provide the necessary corrosion protection and increase boil-over protection. Refer to the Maintenance Booklet for replacement interval. Coolant system design and coolant used determine the replacement interval. The replacement interval published in the Maintenance Booklet is only applicable if MB 325.0 Anticorrosion/Antifreeze solution or other Mercedes-Benz approved products of equal specification are used to renew the coolant concentration or bring it back up to the proper level. For information on other Mercedes-Benz approved products of equal specification, contact an authorized Mercedes-Benz Center or visit www.mbusa.com (USA only). To provide important corrosion protection, the solution must be at least 50% anticorrosion/antifreeze (equivalent to freeze protection to approximately -35‡ [-37†]).

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 363
Version: 2.11.8.1

Fuels, coolants, lubricants, etc.

363

If you use a solution that is more than 55% anticorrosion/antifreeze (freeze protection to approximately -49‡ [-45†]), the engine temperature will increase due to the lower heat transfer capability of the solution. Therefore, do not use more than this amount of anticorrosion/antifreeze. If the coolant level is low, water and MB 325.0
Anticorrosion/Antifreeze should be used to bring it up to the proper level (have cooling system checked for signs of leakage). Please make sure the mixture is in accordance with label instructions. The water in the cooling system must meet minimum requirements, which are usually satisfied by normal drinking water. If you are not sure about the water quality, contact an authorized Mercedes-Benz Center.

Anticorrosion/antifreeze Your vehicle contains a number of aluminum parts. The use of aluminum components in motor vehicle engines necessitates that anticorrosion/antifreeze coolant used in such engines be specifically formulated to protect the aluminum parts. Failure to use such anticorrosion/antifreeze coolant will result in a significantly shortened service life. Therefore, the following product is strongly recommended for use in your vehicle: MB 325.0 Anticorrosion/Antifreeze agent. Before the start of the winter season (or once a year in hot southern regions), you should have the anticorrosion/antifreeze concentration checked. The coolant is also regularly checked each time you bring your vehicle to an authorized Mercedes-Benz Center for service.

Cooling system

Model

ML 350 BlueTEC 4MATIC ML 350
ML 350 4MATIC ML 550 4MATIC ML 63 AMG

Approximate freeze protection -35‡ (-37†) 5.0 US qt (4.75 l)

-49‡ (-45†) 5.5 US qt (5.2 l)

6.3 US qt (6.0 l) 6.1 US qt (5.8 l)

7.0 US qt (6.6 l) 6.8 US qt (6.4 l)

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 364
Version: 2.11.8.1

364 Fuels, coolants, lubricants, etc.

Washer system and headlamp cleaning system G Warning! Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/ antifreeze on hot engine parts, because it may ignite and burn. You could be seriously burned.

X Use MB Windshield Washer Concentrate

“MB SummerFit”.

X Mix with water for temperatures above

freezing point.

X Mix with commercially available premixed

washer solvent/antifreeze for temperatures below freezing point.

Washer fluid mixing ratio For temperatures above the freezing point: 1 part “MB SummerFit” to 100 parts water (1.34 fl oz [40 ml] “MB SummerFit” to 1 gal [4.0 l] water) For temperatures below freezing point: 1 part “MB SummerFit” to 100 parts solvent (1.34 fl oz [40 ml] “MB SummerFit” to 1 gal [4.0 l] solvent)

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 365
Version: 2.11.8.1

Service and Literature Your authorized Mercedes-Benz Center has trained technicians and Genuine Mercedes- Benz Parts to service your vehicle properly. For expert advice and quality service, contact an authorized Mercedes-Benz Center. If you are interested in obtaining service literature for your vehicle, please contact an authorized Mercedes-Benz Center. We consider this the best way for you to obtain accurate information for your vehicle. For further information you can find us on the Mercedes-Benz web site www.mbusa.com (USA only) or www.mercedes-benz.ca (Canada only). G Warning! To help avoid personal injury, be extremely careful when performing any service work or repairs. Improper or incomplete service or the use of incorrect or inappropriate parts or materials may damage the vehicle or its equipment, which may in turn result in personal injury. If you have any questions about carrying out any type of service, turn to the advice of an authorized Mercedes-Benz Center. We reserve the right to make changes in design and equipment. Therefore, information, illustrations and descriptions in this Operator’s Manual might differ from your vehicle. Reprinting, translation and copying, even of excerpts, is not permitted without our prior authorization in writing. Press time September 11, 2009
GSP/OIS Printed in U. S. A.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 366
Version: 2.11.8.1

É1645841383}ËÍ 1645841383

Order no. 6515 4317 13 Part no. 164 584 13 83 Edition B 2010