2010 Mercedes-benz M Class Owners Manual

of 10 seconds or until the engine runs surge-free.

If the engine does not start: X Turn the SmartKey in the starter switch

once more to position 2 for at least 10 seconds.

X Return the SmartKey in the starter switch

to position 0.

X Turn the SmartKey in the starter switch once more to position 3 and hold it there for a maximum of 10 seconds or until the engine runs surge-free.

X If necessary, repeat the above steps. If the engine still does not start after 3 attempts: Do not make any further attempts to start the engine. Contact an authorized Mercedes- Benz Center or call Roadside Assistance (Y page 201). i When the malfunction indicator lamp

= (USA only) or ; (Canada only) in the instrument cluster has been illuminated for the above condition, it will remain illuminated until the engine was cycled on and off four times in a row.

AdBlue® (diesel engine only)

The BlueTEC exhaust gas aftertreatment system requires a reducing agent (AdBlue®) in order to function properly. Refilling with AdBlue® is part of the regular maintenance service work. A tankful of AdBlue® should suffice until the next maintenance service under normal driving conditions. When the AdBlue® tank is low, the message Check Additive See Operator’s Manual appears in the multifunction display. When the AdBlue® level drops to the minimum level, the message Remaining Starts: 20 appears in the multifunction display.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 332
Version: 2.11.8.1

332 AdBlue® (diesel engine only)

i When the message Remaining Starts: 20 appears in the multifunction display, you can start the engine 20 more times. If you do not add AdBlue®, the engine cannot be started beyond that point. Fill the AdBlue® tank with approximately 1 gal (3.79 l) AdBlue® (corresponds to approximately 2 AdBlue® refill containers) or have the AdBlue® tank filled by an authorized Mercedes-Benz Center.

i For refilling outside the maintenance service intervals, refill the AdBlue® tank with approximately 1 gal (3.79 l) AdBlue® (corresponds to approximately 2 AdBlue® refill containers).

Always use the particular AdBlue® refill containers for refilling outside the maintenance service interval. Contact an authorized Mercedes-Benz Center or call Roadside Assistance if necessary (Y page 201). Additional information on BlueTEC exhaust gas aftertreatment and AdBlue® is available at any authorized Mercedes-Benz Center.

Refilling with AdBlue® G Warning! Make sure RAdBlue® does not come into contact with

skin, eyes, or clothing

Rto keep AdBlue® out of the reach of children

If you and/or others have come into contact with AdBlue®: RIf AdBlue® has gotten into contact with

eyes, flush with plenty of water immediately and seek medical help.

RClean affected skin immediately with plenty

of water.

RIf AdBlue® was swallowed, rinse mouth

immediately with plenty of water and drink plenty of water. Consult a physician. G Warning! When opening the filler cap of the AdBlue® tank ammonia gas vapors may escape. Refill AdBlue® in a well ventilated area only. Ammonia gas vapors have a pungent odor and are particularly irritating for your skin, mucous membranes, and eyes. Inhaling ammonia gas vapors will cause burning eyes, nose, and throat, as well as coughing and watering eyes.

! Only use AdBlue® complying with ISO 22241. Do not add additives to AdBlue® and do not dilute AdBlue® with water. Otherwise, the BlueTEC exhaust gas aftertreatment system could be damaged. Damage caused by using additives or diluting with water are not covered by the Mercedes-Benz Limited Warranty.

! Rinse surfaces that have come into

contact with AdBlue®, or remove AdBlue® with a moist cloth and cold water immediately. If AdBlue® has crystallized already, use cold water and a sponge. AdBlue® residues will crystallize and soil the affected surfaces.

! AdBlue® is not a fuel additive and must

not be added to the diesel fuel tank. If AdBlue® reaches the diesel fuel tank, the engine could be damaged which is not covered by the Mercedes-Benz Limited Warranty.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 333
Version: 2.11.8.1

AdBlue® (diesel engine only)

333

For more information on AdBlue®, see (Y page 361). The AdBlue® filler neck is located under the cargo compartment floor. X Switch off the ignition. X Open the tailgate (Y page 75). X Lift the cargo compartment floor

(Y page 268).

X Turn AdBlue® filler cap cover : counterclockwise and remove it.

X Turn AdBlue® filler cap ;

counterclockwise and open it. Filler cap ; is tethered with a plastic strap.

X Pull dust cap off of AdBlue® refill container

=.

X Place AdBlue® refill container = on the

filler neck as illustrated and tighten it moderately (hand-tight) by turning it clockwise.

! Make sure to tighten the AdBlue® refill container only moderately, i.e. hand-tight, as you could otherwise damage it.

X Push AdBlue® refill container = down.

The AdBlue® tank is filled. This may take up to 1 minute.

i When you stop pushing the AdBlue® refill

container down, the filling process is stopped and you can remove the refill container.

X Release AdBlue® refill container =. X Turn AdBlue® refill container = counterclockwise and remove it.

X Place AdBlue® filler cap ; (Y page 332) on

filler neck and turn it clockwise.

164_AKB; 7; 31, en-US d2ureepe,

334 Battery

X Place AdBlue® filler cap cover : as

illustrated and turn it clockwise to its stop.

X Lower cargo compartment floor. X Close the tailgate. X Drive the vehicle at a speed of at least 10 mph (16 km/h). The message Check Additive See Operator’s Manual disappears after approximately 1 minute. i If the message Check Additive See Operator’s Manual still appears in the multifunction display, refill with one more container of AdBlue®.

i Have the AdBlue® level checked and, if necessary, filled completely afterward at an authorized Mercedes-Benz Center.

Battery Safety notes A battery should always be sufficiently charged in order to achieve its rated service life. Refer to Maintenance Booklet for battery maintenance intervals. If you use your vehicle mostly for short- distance trips, you will need to have the battery charge checked more frequently. When replacing a battery, always use a battery approved by Mercedes-Benz. If you do not intend to operate your vehicle for an extended period of time, contact an authorized Mercedes-Benz Center about steps you need to observe. G Warning! HYBRID vehicles: It is imperative that you read the HYBRID Supplemental Operating Instructions included in your vehicle literature portfolio. You may otherwise not recognize potential danger.

2009-09-11T12:07:36+02:00 - Seite 334
Version: 2.11.8.1

G Warning! Observe all safety instructions and precautions when handling automotive batteries.

Risk of explosion.

Fire, open flames and smoking are prohibited when handling batteries. Avoid creating sparks. Battery acid is caustic. Do not allow it to come into contact with skin, eyes or clothing. Wear suitable protective clothing, especially gloves, apron and faceguard. Wear eye protection. Rinse any acid spills immediately with clear water. Contact a physician if necessary. Keep children away.

Follow the instructions in this Operator’s Manual.

A battery contains materials that can harm the environment if disposed of improperly. A large 12 V storage battery contains lead. Recycling of the battery is the preferred method of disposal. Many states (USA only) or provinces (Canada only) require sellers of batteries to accept the old battery for recycling. G Warning! Failure to follow these instructions can result in severe injury or death. Never lean over batteries while connecting. You might get injured.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 335
Version: 2.11.8.1

Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking etc. G Warning! Do not place metal objects on the battery as this could result in a short circuit. Use leak-proof batteries only to avoid the risk of acid burns in the event of an accident. Take care that you do not become statically charged, e.g. by wearing synthetic clothing or rubbing against textiles. For this reason, you also should not pull or push the battery over carpets or other synthetic materials. Never touch the battery first. First touch the outside body of the vehicle in order to release any possible electrostatic charges. Do not rub the battery with rags or cloths. The battery could explode if touched due to electrostatic charge or due to spark formation.

! The battery is a Valve-Regulated Lead Acid (VRLA) battery, also referred to as “fleece” battery. Such batteries do not require topping-up of the electrolyte level. VRLA batteries therefore do not have cell caps and the battery cover is non-removable. Do not attempt to open the battery as otherwise the battery will be damaged. VRLA batteries do not require topping-up of the electrolyte level. They cannot be opened to check the electrolyte level. However, the battery condition must be checked periodically by performing a battery conductance test. Refer to Maintenance Booklet for battery condition testing intervals.

Battery

335

The factory-equipped battery may only be replaced with a battery that Rhas the same security features Ris of identical size Ris of identical voltage Ris of identical capacity

! As any other battery, the battery may

discharge if you do not operate the vehicle for an extended period of time. Have the battery disconnected at a qualified workshop or an authorized Mercedes-Benz Center in such a case. You may also connect an accessory battery charge unit expressly approved by Mercedes-Benz for your vehicle model to maintain the battery charge. Contact an authorized Mercedes- Benz Center for further information. The battery, the battery ventilation hose and the lateral plug must always be securely installed when the vehicle is in operation.

! Never loosen or detach battery terminal clamps while the engine is running or the SmartKey is in the starter switch or KEYLESS-GO button is in position 1. Otherwise the alternator and other electronic components could be severely damaged. Have the battery checked regularly at an authorized Mercedes-Benz Center. Refer to Maintenance Booklet for maintenance intervals or contact an authorized Mercedes-Benz Center for further information.

i After battery power was interrupted, do

the following: RSet the clock (Y page 132).

Vehicles with COMAND system with navigation module: Time and date are set automatically.

RSynchronize the door windows

(Y page 102).

164_AKB; 7; 31, en-US d2ureepe,

336

Jump starting

2009-09-11T12:07:36+02:00 - Seite 336
Version: 2.11.8.1

RSynchronize the power tilt/sliding

sunroof (Y page 186).

RSynchronize the exterior rear view

mirrors (Y page 91).

Charging the battery G Warning! Never charge a battery while still installed in the vehicle unless the accessory battery charge unit approved by Mercedes-Benz is being used. Gases may escape during charging and could cause an explosion that may result in personal injury, paint damage or corrosion. An accessory battery charge unit specially adapted for Mercedes-Benz vehicles and tested and approved by Mercedes-Benz is available. It permits the charging of the battery in its installed position. Contact an authorized Mercedes-Benz Center for information and availability. Charge battery in accordance with the separate instructions for the accessory battery charger. Have the battery charged at an authorized Mercedes-Benz Center. If you charge the battery yourself, follow the operating instructions for your charging device. Only use a battery charge unit with a maximum charging voltage of 14.8 V. X Charge battery in accordance with the

instructions of the battery charger manufacturer.

Jump starting

G Warning! Failure to follow these directions will cause damage to the electronic components, and

can lead to a battery explosion and severe injury or death. Never lean over batteries while connecting or jump starting. You might get injured. Battery fluid contains sulfuric acid. Do not allow this fluid to come in contact with eyes, skin or clothing. In case it does, immediately flush affected area with water, and seek medical help if necessary. A battery will also produce hydrogen gas, which is flammable and explosive. Keep flames or sparks away from battery, avoid improper connection of jumper cables, smoking, etc. Attempting to jump start a frozen battery can result in it exploding, causing personal injury. Read all instructions before proceeding. G Warning! HYBRID vehicles: It is imperative that you read the HYBRID Supplemental Operating Instructions included in your vehicle literature portfolio. You may otherwise not recognize potential danger.

! Do not tow-start the vehicle. You could

otherwise seriously damage the automatic transmission which is not covered by the Mercedes-Benz Limited Warranty.

! Jump starting should only be performed using the jump-start terminals located in the engine compartment. Avoid repeated and lengthy starting attempts. Do not attempt to start the engine using a battery quick-charge unit. If the engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized Mercedes-Benz Center. Excessive unburned fuel generated by repeated failed starting attempts may

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 337
Version: 2.11.8.1

Jump starting 337

damage the catalytic converter31 and may present a fire risk. Make sure the jumper cables do not have loose or missing insulation. Make sure the cable clamps do not touch any other metal part while the other end is still attached to a battery.

If the battery is discharged, the engine can be started with jumper cables and the fully charged battery of another vehicle or an equivalent starter pack. Observe the following: RAccess to the battery is not possible on all vehicles. If you cannot access the battery of the other vehicle, provide jump start power by an external battery or starter pack.

RJump starting should only be performed

when the engine and catalytic converter32
are cold.

RDo not start the engine if the battery is

frozen. Let the battery thaw out first.

ROnly jump start from batteries with the

same voltage rating (12 V). Jump starting

with a more powerful battery could damage the vehicle’s electrical system. Such damage will not be covered by the Mercedes-Benz Limited Warranty.

ROnly use jumper cables with sufficient

cross-section and insulated terminal clamps.

RAlways make sure the jumper cables are not on or near pulleys, fans or other parts that move when an engine is started or running.

RShould the battery be drained completely, let the donating power source charge the vehicle for several minutes before reattempting the starting process.

The jump-start contacts are located in the engine compartment on the passenger side. X Make sure the two vehicles do not touch. X Switch off all electrical consumers. X Engage the parking brake. X Make sure the automatic transmission is in

park position P.

X Open the hood (Y page 213).

31 Vehicles with gasoline engine only. 32 Vehicles with gasoline engine only.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 338
Version: 2.11.8.1

338 Towing the vehicle

Position C represents the charged battery of another vehicle or an equivalent starter pack. X Flip up cover : of positive terminal = in

direction of arrow.

! Never invert the terminal connections! X Connect positive terminal ; of charged

battery C with positive terminal = with a jumper cable. Clamp the cable to positive terminal ; of charged battery C first. X Start engine of the vehicle with charged

battery C and run at idle speed.

X Slide cover A from negative terminal B in

direction of arrow.

X Connect negative terminal ? of charged battery C with negative terminal B with a jumper cable. Clamp the cable to negative terminal ? of charged battery C first.

X Start engine of the vehicle with the

discharged battery and run at idle speed. You can now turn on the electrical consumers. Do not switch on the headlamps under any circumstances.

X Remove the jumper cables from negative

terminals ? and B first.

X Remove the jumper cables from positive

terminals ; and =. You can now switch on the headlamps. X Close cover : of positive terminal =. X Slide cover A back onto negative terminal

B.

X Have the battery checked at the nearest

authorized Mercedes-Benz Center.

Towing the vehicle Safety notes Mercedes-Benz recommends that the vehicle be transported with all wheels off the ground using flatbed or appropriate wheel lift/dolly equipment. This method is preferable to other types of towing. G Warning! HYBRID vehicles: It is imperative that you read the HYBRID Supplemental Operating Instructions included in your vehicle literature

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 339
Version: 2.11.8.1

Towing the vehicle 339

portfolio. You may otherwise not recognize potential danger.

! To prevent damage during transport, do

not tie down vehicle by its chassis or suspension parts.

If circumstances do not permit the recommended towing methods, the vehicle may be towed with all wheels on the ground only so far as necessary to have the vehicle moved to a safe location where the recommended towing methods can be employed. ! Before towing the vehicle observe the

following instructions: RDo not tow-start the vehicle. You could

otherwise seriously damage the automatic transmission which is not covered by the Mercedes-Benz Limited Warranty.

RDo not tow with sling-type equipment. Towing with sling-type equipment over bumpy roads will damage radiator and supports.

RTowing of the vehicle should only be

done using the properly installed towing eye bolt. Never attach a tow cable, tow rope or tow rod to the vehicle chassis, frame or suspension parts.

G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

! Avoid pulling the vehicle abruptly or

diagonally, since it could result in damage to the chassis alignment.

! Do not use the towing eye bolt for

recovery, as this could damage the vehicle. If in doubt, recover the vehicle with a crane.

i If the battery is disconnected or

discharged Rthe SmartKey will not turn in the starter

switch

Rthe automatic transmission will remain in

park position P

For more information see “Battery” (Y page 334) or “Jump starting” (Y page 336).

Installing towing eye bolt Depending on whether you are towing a vehicle or you are being towed, the towing eye bolt can be screwed into threaded holes which are located behind covers on each bumper. The towing eye bolt is supplied with the vehicle tool kit, located in the cargo compartment underneath the cargo compartment floor (Y page 268). X Take the towing eye bolt out of the space underneath the cargo compartment floor.

Removing cover in front bumper

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 340
Version: 2.11.8.1

340 Towing the vehicle

Vehicles with AMG Sport Package X Press mark on cover : as indicated by the

arrow.

X Lift cover : off to reveal the threaded hole

for the towing eye bolt.

Removing cover in rear bumper G Warning! In order to avoid possible serious burns or injury, use extreme caution when removing the rear cover, because the rear exhaust pipe is extremely hot.

Vehicles with Sport Package

Vehicles with AMG Sport Package X Press mark on cover : as indicated by the

arrow.

X Vehicles with Sport Package: Pry

cover : with a flat, blunt object as a lever. X Vehicles with AMG Sport Package: Press mark on cover : as indicated by the arrow. X Lift cover : off to reveal the threaded hole

for the towing eye bolt.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 341
Version: 2.11.8.1

Fixing towing eye bolt

Example illustration front bumper X Take the towing eye bolt and, if so

equipped, the wheel wrench from the vehicle tool kit.

X Screw towing eye bolt ; clockwise into

threaded hole to its stop.

X Insert wheel wrench into towing eye and tighten towing eye bolt ; by turning it clockwise.

or X If your vehicle is not equipped with a wheel

wrench, use a suitable object to turn the towing eye bolt.

Removing towing eye bolt X Loosen towing eye bolt ; by turning it

counterclockwise.

X Unscrew towing eye bolt ;. X Reinstalling cover: Engage cover :

(Y page 339) at top and press at bottom. X Store the towing eye bolt ; and wheel

wrench back into the vehicle tool kit.

Towing with one axle raised ! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

! Vehicles with 4MATIC: Do not tow with

one axle raised. Doing so could damage the

Towing the vehicle 341

transfer case, which is not covered by the Mercedes-Benz Limited Warranty. All wheels must be on or off the ground. Observe instructions for towing the vehicle with all wheels on the ground.

When towing the vehicle with one axle raised, the wheels on the ground have to move freely. Therefore follow the respective steps below, after the front or the rear axle being raised:

Towing with the front axle raised X Switch off the automatic central locking

X Switch on the hazard warning flasher

(Y page 135).

(Y page 96).

X Make sure the automatic transmission remains in neutral position N. Observe instructions, see “Remaining in neutral position N” (Y page 111).

! Because the ESP® operates

automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the vehicle is being towed with one axle raised. Active braking action through the ESP® may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.

! Keep in mind that it is important for the SmartKey to be left in starter switch with the ignition switched off. As soon as the SmartKey is removed from the starter switch the automatic transmission will shift to park position P.

164_AKB; 7; 31, en-US d2ureepe,

342 Fuses

Towing with the rear axle raised X Switch off the ignition and remove the

SmartKey from the starter switch.

X Switch on the hazard warning flasher

(Y page 96).

X Take the SmartKey or SmartKey with

KEYLESS-GO with you when leaving the vehicle.

Towing with all wheels on the ground G Warning! If circumstances require towing the vehicle with all wheels on the ground, always tow with a tow bar if: Rthe engine will not run Rthere is a malfunction in the brake system Rthere is a malfunction in the power supply

or in the vehicle’s electrical system

This is necessary to adequately control the towed vehicle. Prior to towing the vehicle with all wheels on the ground, make sure the SmartKey is in starter switch position 2. G Warning! With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle. Adapt your driving accordingly.

X Make sure the ignition is switched on. X With the vehicle at a standstill, depress the

brake pedal and keep it pressed.

X Shift the automatic transmission into

neutral position N.

X Release the brake pedal. X If engaged, release the parking brake. X Switch on the hazard warning flasher

(Y page 96).

2009-09-11T12:07:36+02:00 - Seite 342
Version: 2.11.8.1

! Keep in mind that it is important to have

the ignition switched on. Removing the SmartKey from the starter switch or opening a front door with the ignition switched off will automatically shift the automatic transmission into park position P.

! The vehicle may be towed only for

distances up to 30 miles (50 km) and at a speed not to exceed 30 mph (50 km/h).

i While being towed with the hazard

warning flasher in use, use the combination switch in the usual manner to signal turns. Only the selected turn signal will operate. Upon canceling the turn signal, the hazard warning flasher will operate again.

Stranded vehicle Freeing a stranded vehicle, on which the wheels are dug into sand or mud, should be done with the greatest of care, especially if the vehicle is heavily loaded. Note the following when freeing a stranded vehicle: RAvoid pulling the vehicle abruptly or

diagonally, since it could result in damage to the chassis alignment.

RNever try to free a vehicle that is still

coupled to a trailer.

RIf possible, a vehicle equipped with a trailer hitch receiver should be pulled backward in its own previously made tracks.

Fuses Introduction The electrical fuses in your vehicle serve to switch off malfunctioning power circuits. If a fuse is blown, the components and systems secured by that fuse will stop operating.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 343
Version: 2.11.8.1

G Warning! Only use fuses approved by Mercedes-Benz with the specified amperage for the system in question and do not attempt to repair or bridge a blown fuse. Using other than approved fuses or using repaired or bridged fuses may cause an overload leading to a fire, and/or cause damage to electrical components and/or systems. Have the cause determined and remedied by an authorized Mercedes-Benz Center. A blown fuse must be replaced by an appropriate spare fuse (recognizable by its color or the fuse rating given on the fuse) of the amperage recommended in the fuse chart. Any Mercedes-Benz Center will be glad to advise you on this subject. i In case of a blown fuse contact Roadside

Assistance or an authorized Mercedes- Benz Center.

If a newly inserted fuse blows again, have the cause determined and rectified by an authorized Mercedes-Benz Center. The fuse chart is located in the cargo compartment with the vehicle tool kit (Y page 268). The fuse chart explains the fuse allocation and fuse amperages.

Before replacing fuses X Engage the parking brake. X Make sure the automatic transmission is in

park position P. The transmission position indicator in the multifunction display should be on P. X Switch off all electrical consumers. X Turn off the engine. X Remove the SmartKey from the starter

switch.

X Vehicles with KEYLESS-GO: Open the

driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door then can be closed again.

Fuses

343

Fuse box in passenger compartment ! Do not use sharp objects such as a

screwdriver to open the fuse box cover in the dashboard. You could damage the fuse box cover or the dashboard.

The fuse box is located behind a cover in the dashboard on the front passenger side.

X Open the front passenger door. X Opening: Open the glove box. X Opening: Insert flat, blunt object as a lever into the edge of fuse box cover : at the position indicated by the arrow.

X Loosen fuse box cover : from the

dashboard using the lever.

X Using your hands, pull fuse box cover :

out and remove.

X Closing: Hook fuse box cover : into holders on the front of the dashboard. X Press fuse box cover : back on until it

engages.

! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

Fuse box in engine compartment X Open the hood.

164_AKB; 7; 31, en-US d2ureepe,

344 Fuses

2009-09-11T12:07:36+02:00 - Seite 344
Version: 2.11.8.1

X Opening: Open the cargo compartment. X Insert a suitable object such as a coin into

the slot of lock :.

X Turn lock : by 90° in direction of arrow. X Remove cover ;. X Closing: Install everything in reverse order.

Emergency engine shutdown If the engine cannot be turned off as described (Y page 108), you may use the following emergency procedure. X Take the fuse chart from the vehicle tool kit

(Y page 268).

X Open the fuse box in engine compartment. X Remove fuse 120.

Find its location in the fuse chart.

Example illustration fuse box ML 350 (ML 350
BlueTEC, ML 550, ML 63 AMG similar) X With a dry cloth, remove any moisture from

fuse box cover :.

X Opening: Pull clamps ; in direction of

arrow.

X Lift fuse box cover : up. X Closing: Make sure the sealing rubber is

positioned properly.

X Press fuse box cover : down and secure

with clamps ;.

! The fuse box cover must be properly

positioned as described. Otherwise, moisture or dirt could enter the fuse box and possibly impair fuse operation.

X Close the hood after checking or replacing

fuses.

Fuse box in cargo compartment

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 345
Version: 2.11.8.1

Vehicle equipment ............................ 346
Parts service ..................................... 346
Warranty coverage ........................... 346
Identification labels .......................... 346
Vehicle specification ML 350 Blue- TEC 4MATIC (164.125) ..................... 348
Vehicle specification ML 350
(164.156) ........................................... 348
Vehicle specification ML 350
4MATIC (164.186) ............................. 349
Vehicle specification ML 550
4MATIC (164.172) ............................. 350
Vehicle specification ML 63 AMG (164.177) ........................................... 351
Rims and tires ................................... 352
Fuels, coolants, lubricants, etc. ...... 356

345

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 346
Version: 2.11.8.1

346

Identification labels

accordance with the terms of the following warranties: RNew Vehicle Limited Warranty REmission System Warranty REmission Performance Warranty RCalifornia, Connecticut, Maine,

Massachusetts, New York, Pennsylvania, Rhode Island, and Vermont Emission Control Systems Warranty33

RState Warranty Enforcement Laws (Lemon

Laws)

Replacement parts and accessories are covered by the Mercedes-Benz Parts and Accessories warranties, copies of which are available at any authorized Mercedes-Benz Center.

Loss of Service and Warranty Information booklet Should you lose your Service and Warranty Information booklet, have an authorized Mercedes-Benz Center arrange for a replacement. It will be mailed to you.

Identification labels

Vehicle equipment

i This Operator’s Manual describes all

features, standard or optional, potentially available for your vehicle at the time of purchase. Please be aware that your vehicle might not be equipped with all features described in this manual.

Parts service

All authorized Mercedes-Benz Centers maintain a stock of Genuine Mercedes-Benz Parts required for maintenance and repair work. In addition, strategically located parts distribution centers provide quick and reliable parts service. More than 300 000 different parts for Mercedes-Benz models are available. Genuine Mercedes-Benz Parts are subjected to stringent quality inspections. Each part has been specifically developed, manufactured or selected for and adapted to Mercedes-Benz vehicles. Therefore, Genuine Mercedes-Benz Parts should be installed. ! Do not use non-genuine Mercedes-Benz parts and accessories not authorized by Mercedes-Benz. Doing so could damage the vehicle, which is not covered by the Mercedes-Benz Limited Warranty. Also, it could compromise the vehicle’s durability or safety.

Warranty coverage

Your vehicle is covered under the terms of the warranties printed in the Service and Warranty Information booklet. Your authorized Mercedes-Benz Center will exchange or repair any defective parts originally installed in the vehicle in

33 Applicable to vehicles with gasoline engine only.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 347
Version: 2.11.8.1

Identification labels

347

data shown in the illustration. Refer to certification label on vehicle for actual data specific to your vehicle.

The Vehicle Identification Number (VIN) can be found Ron certification label : on the driver’s door

B-pillar

Ron passenger side underneath the rear seat

(Y page 347)

Ron the lower edge of the windshield

(Y page 347)

Passenger-side rear seat X Fold seat cushion ? forward

(Y page 189).

X Fold carpet A forward in direction of

arrow. VIN B is now visible.

Example certification label (U.S. vehicles) ; Paintwork code = VIN

Example certification label (Canada vehicles) ; Paintwork code = VIN

i Data shown on certification label are for illustration purposes only. These data are specific to each vehicle and may vary from

C Emission control information label, includes both federal and California certification exhaust emission standards

D Engine number (engraved on engine) E VIN (on lower edge of windshield)

i When ordering parts, please specify

vehicle identification and engine number.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 348
Version: 2.11.8.1

348 Vehicle specification ML 350 (164.156)

Vehicle specification ML 350 BlueTEC 4MATIC (164.125)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment. Engine ΜL 350 BlueTEC 4MATIC

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 1349
Maximum torque acc. to SAE J 1349

642

Diesel 4-stroke

engine

3.27 in (83.00 mm) 3.62 in (92.00 mm)

182.3 cu in (2 987 cm3)

16.5:1

210 hp/3 400 rpm (157 kW/3 400 rpm)

400 lb-ft/

1 600 - 2 400 rpm

(543 Nm/

1 600 - 2 400 rpm)

Maximum engine speed Firing order Poly-V-belt

4 500 rpm

1-4-2-5-3-6
2 035 mm

Electrical system

ΜL 350 BlueTEC 4MATIC

Alternator Starter motor Battery

14 V/220 A 12 V/2.0 kW 12 V/95 Ah

Main dimensions

ΜL 350 BlueTEC 4MATIC

188.5 in (4 788 mm)

83.6 in (2 124 mm)

Overall vehicle length Overall vehicle width34
Overall vehicle height

71.5 in (1 815 mm)35
69.8 - 73.0 in (1 774 - 1 854 mm)36
Wheelbase 114.8 in (2 915 mm) Track, front 63.7 in (1 619 mm) Track, rear 63.8 in (1 621 mm) Ground clearance 8.3 in (210 mm)35

7.3 - 10.3 in (186 - 261 mm)36
39.0 ft (11.6 m)

Turning circle

Weights ΜL 350 BlueTEC 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 350 (164.156)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ΜL 350

Engine, type Mode of operation

272

4-stroke engine, gasoline injection

No. of cylinders

34 Exterior rear view mirrors folded out. 35 Vehicles with steel suspension. 36 Depending on the set vehicle level (vehicles with air suspension program).

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 349
Version: 2.11.8.1

Vehicle specification ML 350 4MATIC (164.186)

349

Engine ΜL 350

Main dimensions ΜL 350

Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134937
Maximum torque acc. to SAE J 1349

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

10.7:1

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 398 mm

Electrical system ML 350

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

14 V/180 A 12 V/1.4 kW 12 V/70 Ah

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)

188.5 in (4 788 mm)

Overall vehicle length Overall vehicle width38
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 8.3 in (210 mm) Turning circle 39.0 ft (11.6 m)

114.8 in (2 915 mm) 64.0 in (1 627 mm) 64.1 in (1 629 mm)

Weights ΜL 350

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 350 4MATIC (164.186)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ΜL 350 4MATIC 272

Engine, type Mode of operation

No. of cylinders Bore Stroke Total piston displacement

4-stroke engine, gasoline injection

3.66 in (92.90 mm) 3.39 in (86.00 mm)

213.5 cu in (3 498 cm3)

37 Premium fuel required. Performance may vary with fuel octane rating. 38 Exterior rear view mirrors folded out.

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 350
Version: 2.11.8.1

350 Vehicle specification ML 550 4MATIC (164.172)

Engine ΜL 350 4MATIC 10.7:1

Compression ratio Output acc. to SAE J 134939
Maximum torque acc. to SAE J 1349

268 hp/6 000 rpm (200 kW/6 000 rpm)

258 lb-ft/

2 400 - 5 000 rpm

(350 Nm/

2 400 - 5 000 rpm)

Maximum engine speed Firing order Poly-V-belt

6 500 rpm

1-4-3-6-2-5
2 398 mm

Electrical system ML 350 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/70 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

Bosch Y 7 MPP33
0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions ΜL 350 4MATIC

Wheelbase 114.8 in (2 915 mm) Track, front 64.0 in (1 627 mm) Track, rear 64.1 in (1 629 mm) Ground clearance 8.3 in (210 mm)41

7.3 - 10.3 in (186 - 261 mm)42
39.0 ft (11.6 m)

Turning circle

Weights ΜL 350 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 550 4MATIC (164.172)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ML 550 4MATIC 273

Engine, type Mode of operation

4-stroke engine, gasoline injection

3.86 in (98.00 mm) 3.56 in (90.50 mm)

333.2 cu in (5 461 cm3)

10.7:1

Main dimensions ΜL 350 4MATIC

Overall vehicle length Overall vehicle width40
Overall vehicle height

188.5 in (4 788 mm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)41
69.8 - 73.0 in (1 774 - 1 854 mm)42

No. of cylinders Bore Stroke Total piston displacement Compression ratio

39 Premium fuel required. Performance may vary with fuel octane rating. 40 Exterior rear view mirrors folded out. 41 Vehicles with steel suspension. 42 Depending on the set vehicle level (vehicles with air suspension program).

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 351
Version: 2.11.8.1

Vehicle specification ML 63 AMG (164.177)

351

Main dimensions ΜL 550 4MATIC Track, front 63.7 in (1 619 mm) Track, rear 63.8 in (1 621 mm) Ground clearance 8.3 in (210 mm)45

7.3 - 10.3 in (186 - 261 mm)46
39.0 ft (11.6 m)

6 500 rpm

Turning circle

1-5-4-2-6-3-7-8

2 398 mm

Weights ΜL 550 4MATIC

Roof load

max. 220 lb (100 kg)

Vehicle specification ML 63 AMG (164.177)

The quoted data apply only to the standard vehicle. Contact an authorized Mercedes- Benz Center for the corresponding data of all special bodies and special equipment.

Engine ML 63 AMG

Engine ML 550 4MATIC

382 hp/6 000 rpm (285 kW/6 000 rpm)

391 lb-ft/

2 800 - 4 800 rpm

(530 Nm/

2 800 - 4 800 rpm)

Output acc. to SAE J 134943
Maximum torque acc. to SAE J 1349

Maximum engine speed Firing order Poly-V-belt

Electrical system ML 550 4MATIC 14 V/180 A 12 V/1.4 kW 12 V/95 Ah NGK PLKR 7A

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

0.031 in (0.8 mm)

15 - 18 lb-ft (20 - 25 Nm)

Engine, type Mode of operation

Main dimensions ΜL 550 4MATIC

Overall vehicle length Overall vehicle width44
Overall vehicle height

Wheelbase

188.5 in (4 788 mm)

83.6 in (2 124 mm)

71.5 in (1 815 mm)45
69.8 - 73.0 in (1 774 - 1 854 mm)46
114.8 in (2 915 mm)

No. of cylinders Bore Stroke Total piston displacement Compression ratio Output acc. to SAE J 134947

43 Premium fuel required. Performance may vary with fuel octane rating. 44 Exterior rear view mirrors folded out. 45 Vehicles with steel suspension. 46 Depending on the set vehicle level (vehicles with air suspension program). 47 Premium fuel required. Performance may vary with fuel octane rating.

156

4-stroke engine, gasoline injection

4.02 in (102.20 mm) 3.72 in (94.60 mm)

378.8 cu in (6 208 cm3)

11.3:1

503 hp/6 800 rpm (375 kW/6 800 rpm)

164_AKB; 7; 31, en-US d2ureepe,

352 Rims and tires

2009-09-11T12:07:36+02:00 - Seite 352
Version: 2.11.8.1

Engine ML 63 AMG

Weights ML 63 AMG

Maximum torque acc. to SAE J 1349
Maximum engine speed Firing order Poly-V-belt

465 lb-ft/5 200 rpm (630 Nm/5 200 rpm)

7 200 rpm

1-5-4-2-6-3-7-8

2 360 mm

Electrical system ML 63 AMG 14 V/180 A 12 V/2.1 kW 12 V/95 Ah

Alternator Starter motor Battery Spark plugs, type Spark plugs, electrode gap Spark plugs, tightening torque

NGK ILZKAR 7A10
0.039 in (1.0 mm)

15 - 18 lb-ft (20 - 25 Nm)

Main dimensions ML 63 AMG

83.6 in (2 124 mm)

189.7 in (4 818 mm)

Overall vehicle length Overall vehicle width48
Overall vehicle height Wheelbase Track, front Track, rear Ground clearance 7.0 - 10.1 in

69.5 - 72.6 in (1 765 - 1 845 mm)49
114.8 in (2 915 mm) 65.5 in (1 664 mm) 65.6 in (1 667 mm)

Turning circle

(177 - 257 mm)49
39.0 ft (11.6 m)

48 Exterior rear view mirrors folded out. 49 Depending on the set vehicle level.

Roof load

max. 220 lb (100 kg)

Rims and tires Notes ! Only use tires which have been tested and

approved by Mercedes-Benz. Tires approved by Mercedes-Benz are developed to provide best possible performance in conjunction with the driving safety systems on your vehicle such as the ABS or the ESP®. Tires specially developed for your vehicle and tested and approved by Mercedes-Benz can be identified by finding the following on the tire’s sidewall: RMO = Mercedes-Benz Original

equipment tires

RMOE = Mercedes-Benz Original Extended

(tires with limited run-flat characteristics) original equipment tires Using tires other than those approved by Mercedes-Benz may result in damage that is not covered by the Mercedes-Benz Limited Warranty.

For information on driving with MOExtended tires, see the “Practical hints” section (Y page 330). i Vehicles with MOExtended system are not factory-equipped with a TIREFIT kit. When retrofitting with tires that do not have run-flat characteristics, you should also equip your vehicle with a TIREFIT kit. TIREFIT kits are available at any authorized Mercedes-Benz Center.

! Using tires other than those approved by

Mercedes-Benz can have detrimental effects, such as

164_AKB; 7; 31, en-US d2ureepe,

2009-09-11T12:07:36+02:00 - Seite 353
Version: 2.11.8.1

Rpoor handling characteristics Rincreased noise Rincreased fuel consumption Moreover, tires and rims not approved by Mercedes-Benz may, under load, exhibit dimensional variations and different tire deformation characteristics that could cause them to come into contact with the vehicle body or axle parts. Damage to the tires or the vehicle may be the result.

i Further information on tires and rims is

available at any authorized Mercedes-Benz Center. The Tire and Loading Information placard with the recommended tire inflation pressures for cold tires is located on the driver’s door B-pillar. Supplemental tire inflation pressure information for driving at high speeds or for vehicle loads less than the maximum loaded vehicle condition can be found on the tire inflation pressure label. The tire inflation pressure label is located on the inside of the fuel filler flap. The tire inflation pressure should be checked regularly and should only be adjusted on cold tires. Follow tire manufacturer’s maintenance recommendation included with the vehicle.

For information on recommended tire inflation pressure and supplemental tire inflation pressure information for special driving situations, see (Y page 219). i Please keep in mind that the vehicle must

be equipped Rwith wheels of identical dimensions on

each axle (left and right)

Rwith tires of identical characteristics all around, i.e. summer tires, winter tires, all-season tires, or MOExtended tires etc.

i The following pages also list the approved rim and tire sizes for equipping your vehicle with winter tires. Winter tires are not available as standard or optional factory

Rims and tires

353

equipment, but can be purchased from an authorized Mercedes-Benz Center. Equipping your vehicle with winter tires approved for your vehicle model may require the purchase of rims of the recommended size for use with these winter tires. This depends on vehicle model and the standard or optional factory- equipped wheel rim/tire configuration on your vehicle. For more information contact an authorized Mercedes-Benz Center.

164_AKB; 7; 31, en-US d2ureepe,

354 Rims and tires