2008 Mercedes-benz CLS Class Owners Manual

! Do not sit on or lean your body weight against the armrest when it is folded down, as you could otherwise damage it.

1 Tab 왘 Pull tab 1 upward. 왘 Fold the covering forward.

Controls in detail Useful features

Opening 왘 Press button 1 right or left and fold

cover 2 sideward.

i The mobile phone cradle (컄 page 253), the Roadside Assistance button • and the Infor- mation button ¡ (컄 page 256) are located below the cover 2.

Rear storage compartment in the rear center console

1 Power outlet (컄 page 250) 2 Cover 왘 Slide cover 2 back.

244

Ruffled storage bags

Ruffled storage bags are located on the back of the front seats.

Warning!

Do not place objects with a combined weight of more than 4.4 lb (2 kg) into the ruffled storage bag. Otherwise, the Occu- pant Classification System OCS (컄 page 71) may not be able to properly approximate the occupant weight category.

The ruffled storage bag is intended for stor- ing light-weight items only.

Controls in detail Useful features

Heavy objects, objects with sharp edges or fragile objects may not be transported in the parcel net. In an accident, during hard brak- ing, or sudden maneuvers, they could be thrown around inside the vehicle and cause injury to vehicle occupants.

The ruffled storage bag cannot protect transported goods in the event of an acci- dent.

Parcel net in front passenger footwell

Warning!

The parcel net is intended for storing light-weight items only.

Heavy objects, objects with sharp edges or fragile objects may not be transported in the parcel net. In an accident, during hard brak- ing, or sudden maneuvers, they could be thrown around inside the vehicle and cause injury to vehicle occupants.

The parcel net cannot protect transported goods in the event of an accident.

A small convenience parcel net is located in the front passenger footwell. It is for small and light items, such as road maps, mail, etc.

245

Controls in detail Useful features

Cup holders

Warning!

In order to help prevent spilling liquids on vehicle occupants and/or vehicle equip- ment, only use containers that fit into the cup holder. Use lids on open containers and do not fill containers to a height where the contents, especially hot liquids, could spill during braking, vehicle maneuvers, or in an accident. Liquids spilled on vehicle occu- pants may cause serious personal injury. Liquids spilled on vehicle equipment may cause damage not covered by the Mercedes-Benz Limited Warranty.

The cup holder must be extended when in use with bottles.

When not in use, keep the cup holder closed. An open cup holder may cause injury to you or others when contacted during braking, vehicle maneuvers, or in an acci- dent.

Keep in mind that objects placed in the cup holder may come loose during braking, vehi- cle maneuvers, or in an accident and be thrown around in the vehicle interior. Objects thrown around in the vehicle interi- or may cause an accident and/or serious personal injury.

Cup holder in the center console

Extending the cup holder

왘 Briefly press mark on cup holder.

The cup holder automatically extends upward.

Retracting the cup holder 왘 Press mark on cup holder and push cup

holder in until it engages.

246

Removing the cup holder

Cup holder in the rear center console

i The cup holder can be removed for cleaning. Clean the cup holder with clear, lukewarm water. 왘 Extend cup holder (컄 page 246). 왘 Press mark on cup holder and remove

cup holder by pulling it upward.

Reinstalling the cup holder 왘 Insert cup holder into opening.

! Make sure that the cup holder is correctly positioned in the guide while you are reinstalling it. Otherwise the cup holder can be damaged. 왘 Press mark on cup holder and press cup holder downward until it engages.

1 Cover 왘 Slide cover 1 forward.

Removing cup holder

i The cup holder can be removed for cleaning. Clean the cup holder with clear, lukewarm water.

Controls in detail Useful features

1 Cup holder 2 Locking pin 왘 Move pin 2 in direction of arrow to un-

lock the cup holder.

왘 With the cup holder unlocked, take cup

holder 1 out upwards.

Reinstalling cup holder 왘 Insert cup holder 1. 왘 Move pin 2 against direction of arrow

to lock the cup holder.

247

Controls in detail Useful features

Cup holder in the rear seat armrest

Ashtrays

Removing ashtray insert

Center console ashtray

Warning!

Remove front ashtray only with vehicle standing still. Set the parking brake to secure vehicle from movement. Move gear selector lever to position N. With gear selec- tor lever in position N, turn off the engine.

왘 Secure vehicle from movement by set- ting the parking brake. Move the gear selector lever to position N. Now you have more room to take out the insert.

왘 Push sliding button 2 to the right and

hold.

왘 Grip and remove insert from ashtray

frame.

왘 Briefly press the front of the rear arm-

rest. The cup holder extends automatically.

1 Cover 2 Sliding button

Opening ashtray 왘 Briefly press the marking on the bot-

tom of cover 1. The ashtray opens automatically.

248

Controls in detail Useful features

Reinstalling ashtray insert 왘 Install insert by pushing it back into

frame until it engages again.

Opening rear seat ashtray 왘 Briefly press the top of ashtray 3.

Cigarette lighter

The ashtray opens.

Warning!

Rear door ashtray

1 Chrome bar 2 Insert slides out 3 Ashtray

Removing ashtray insert 왘 Pull chrome bar 1 in direction of ar-

row. Remove insert 2 upwards from ash- tray frame.

Reinstalling ashtray insert 왘 Install insert by pushing it back into ashtray frame until it engages again.

Never touch the heating element or sides of the lighter; they are extremely hot. Hold the knob only.

Make sure that any children traveling with you do not injure themselves or start a fire with the hot cigarette lighter.

When leaving the vehicle, always remove the SmartKey or the SmartKey with KEYLESS-GO* from the starter switch, take it with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. A child’s unsupervised access to a vehicle could re- sult in an accident and/or serious personal injury.

249

Controls in detail Useful features

The cigarette lighter is located in the cen- ter console compartment in front of the center armrest (컄 page 30).

1 Cigarette lighter 왘 Switch on the ignition (컄 page 38). 왘 Push in cigarette lighter 1.

The lighter will pop out automatically when hot.

250

! The lighter socket can be used to accommodate 12V DC electrical accessories (up to a maximum 85 W) designed for use with the standard “cigarette lighter” plug type. Keep in mind, however, that connecting accessories to the lighter socket (for example extensive con- necting and disconnecting, or using plugs that do not fit properly) can damage the lighter socket. With the socket damaged, the lighter may no longer be able to be placed in the heating (pushed-in) position, or the lighter may pop out too early with the lighter not hot enough. To help avoid damaging the cigarette lighter socket, we recommend connecting 12V DC elec- trical accessories designed for use with a stan- dard “cigarette lighter” plug type to the 12V power outlets (컄 page 250) in your vehicle whenever possible.

Power outlets

! Make sure no fluids come into contact with the power outlet, as this could cause a short cir- cuit.

Power outlet in rear center console 1 Power outlet 2 Cover 왘 Slide cover 2 back.

i Make sure the override switch is not activat- ed (컄 page 87). The power outlet in the rear cen- ter console will not function if the override switch is activated.

Heated steering wheel (Canada only)

The steering wheel heating warms up the leather area of the steering wheel. The stalk is on the lower left-hand side of the steering wheel.

Power outlet in trunk 1 Power outlet

i The power outlet can be used to accommo- date 12-V DC electrical accessories (e.g. air pump, auxiliary lamps) up to a maximum 180 W.

1 Switching on 2 Switching off 3 Indicator lamp

Controls in detail Useful features

Switching on 왘 Switch on the ignition (컄 page 38). 왘 Turn switch at the tip of stalk in direc-

tion of arrow 1. The steering wheel is heated. Indicator lamp 3 comes on.

i The steering wheel heating is temporarily suspended while indicator lamp 3 remains on when 앫 the temperature of the vehicle interior is

above 86°F (30°C)

앫 the temperature of the steering wheel is

above 95°F (35°C)

When these conditions do not apply anymore, steering wheel heating continues.

251

Controls in detail Useful features

Switching off 왘 Turn switch at the tip of stalk in direc-

tion of arrow 2. The heated steering wheel is switched off. Indicator lamp 3 goes out.

i Indicator lamp 3 flashes or goes out 앫 in case of power surge or undervoltage 앫 in case of a steering wheel heating malfunc-

tion

i The steering wheel heating switches off au- tomatically when you remove the SmartKey from the starter switch or, on vehicles with KEYLESS-GO*, when you switch off the ignition (컄 page 61) and open the driver’s door. For information on steering wheel, see “Multifunction steering wheel” (컄 page 140).

Floormats

Warning!

Whenever you are using floormats, make sure there is enough clearance and that the floormats are securely fastened.

Floormats should always be securely fas- tened using eyelets 2 and retainer pins 1. Before driving off, check that the floormats are securely in place and adjust them if nec- essary. A loose floormat could slip and hinder proper functioning of the pedals.

Do not place several floormats on top of each other as this may impair pedal movement.

252

1 Retainer pins 2 Eyelets

i To install or remove the floormat more easi- ly, move the driver’s seat or front passenger seat as far to the rear as possible (컄 page 42).

Removing 왘 Pull floormats off of retainer pins 1. 왘 Remove the floormats.

Installing 왘 Lay down the floormat. 왘 Press the floormat eyelets 2 onto re-

tainer pins 1.

Telephone*

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or serious personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit, should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. The external antenna must be approved by Mercedes-Benz. Please contact an autho- rized Mercedes-Benz Center for informa- tion on the installation of an approved external antenna. Refer to the radio trans- mitter operation instructions regarding use of an external antenna.

Warning!

Please do not forget that your primary re- sponsibility is to drive the vehicle. A driver’s attention to the road must always be his/her primary focus when driving. For your safety and the safety of others, we rec- ommend that you pull over to a safe location and stop before placing or taking a tele- phone call. If you choose to use the telephone1 while driving, please use the hands-free device and only use the telephone when road, weather and traffic conditions permit. Some jurisdictions prohibit the driver from using a mobile telephone while driving a vehicle.

Only operate the COMAND (Cockpit Man- agement and Data System)1 if road, weather and traffic conditions permit.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

1 Observe all legal requirements.

Controls in detail Useful features

When the mobile phone is inserted in the cradle, you can operate the telephone us- ing the following devices: 앫 mobile phone keypad 앫 COMAND (see separate operating in-

structions)

앫 buttons s and t on the multi-

function steering wheel

앫 Voice Control* (see separate operating

instructions)

See also separate operating manual for in- structions on how to use the mobile phone.

i Various mobile phone cradles can be in- stalled in the cockpit. These mobile phone cra- dles can be obtained from an authorized Mercedes-Benz Center. The functions and services available to you while using the mobile phone depend on your service provider and the type of mobile phone you are using.

253

Controls in detail Useful features

The cradle is located in the center armrest. 왘 Open the telephone compartment un-

der center armrest (컄 page 243).

Inserting mobile phone in mobile phone cradle Once the mobile phone has been inserted in the mobile phone cradle, calls can only be made via the Voice Control*.

! Do not try to remove the mobile phone along with the cradle. You could otherwise damage the mobile phone cradle. 왘 If applicable, remove the cover for the external antenna connection from the back of the mobile phone and store it in a safe place. Be sure to comply with the mobile phone’s operating instructions, as well.

254

The mobile phone is linked to the hands-free device and the multifunc- tion steering wheel. The battery is charged depending on its charge status and the position of the SmartKey in the starter switch. The charge procedure will be indicated in the mobile phone’s display.

You can place or receive phone calls. You can control other functions of the mobile phone via the control system (컄 page 166), COMAND or Voice Control* (see separate operating instructions).

i When you take the SmartKey or SmartKey with KEYLESS-GO* out of the starter switch, the mobile phone remains switched on for approxi- mately 10 minutes. If you place or receive a call during this time, the mobile phone switches off 10 minutes after the call has been completed.

Example illustration 1 Insert the mobile phone 2 Connector contact 3 Mobile phone cradle 왘 Slide the lower end of the mobile phone

into connector contact 2 on cradle 3.

왘 Push the top of the mobile phone in di- rection of arrow 1, until the lug on the mobile phone release button engages. The mobile phone is connected to the network via the external antenna.

Controls in detail Useful features

Removing mobile phone from mobile phone cradle

Changing mobile phone cradle If you require a different cradle for your mobile phone, remove the present cradle before installing a new one.

Removing an existing mobile phone cradle

왘 Press release button in direction of

arrow 1 and take mobile phone cradle 3 out in direction of arrow 2.

Installing a different mobile phone cradle

Example illustration 1 Release catch for mobile phone 2 Mobile phone cradle

i When using a flip-style mobile phone, open flip top before removing from the cradle while a call is connected. Otherwise, the call will be dis- connected. 왘 Press release catch in direction of

arrow 1 and take mobile phone out of mobile phone cradle 2.

Example illustration 1 To release the mobile phone cradle 2 To remove the mobile phone cradle 3 Mobile phone cradle

Example illustration 1 Contact plate 2 Recesses 3 Mobile phone cradle 왘 Insert mobile phone cradle 3 into

recesses 2 of contact plate 1.

왘 Push mobile phone cradle 3 forward

until it engages.

255

왘 To activate, press the SOS button, the

Roadside Assistance button • or the Information button ¡, depend- ing on the type of response required.

i The SOS button is located in the overhead control panel (컄 page 258). The Roadside Assistance button • and the Information button ¡ are located below the center armrest cover (컄 page 243).

Controls in detail Useful features

Tele Aid

! The initial activation of the Tele Aid system may only be performed by completing the sub- scriber agreement and placing an acquaintance call using button ¡. Failure to complete ei- ther of these steps will result in a system that is not activated. If you have any questions regarding activation, please call the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada).

Shortly after the completion of your Tele Aid acquaintance call, you will receive a user ID and password. By visiting www.mbusa.com and selecting “Tele Aid” (USA only), you will have access to account information, remote door unlock and more.

256

The Tele Aid system (Telematic Alarm Identification on Demand) The Tele Aid system consists of three types of response: 앫 automatic and manual emergency 앫 roadside assistance 앫 information The Tele Aid system is operational provid- ing that the vehicle’s battery is charged, properly connected, not damaged and cel- lular and GPS coverage is available. The speaker volume of a Tele Aid call can be adjusted when using the volume control on the COMAND System or on the multi- function steering wheel. To raise, turn the rotary volume control on COMAND System clockwise or press button æ on the multifunction steering wheel. To lower, turn the rotary volume control on COMAND System control counterclock- wise or press button ç on the multi- function steering wheel.

Controls in detail Useful features

! The Tele Aid system utilizes the cellular net- work for communication and the GPS (Global Po- sitioning System) satellites for vehicle location. If either of these signals are unavailable, the Tele Aid system may not function and if this oc- curs, assistance must be summoned by other means.

i When a Tele Aid call has been initiated, the COMAND System audio is muted and the select- ed mode (radio, tape or CD) pauses. The optional cellular phone (if installed) and inserted in cradle switches off. If you must use this phone, we rec- ommend that you use it only with the vehicle at a standstill in a safe location. Remove the phone from the cradle and place the call. The naviga- tion* system (if engaged) will continue to run. The multifunction display in the instrument clus- ter is available for use, and spoken commands are only available by pressing the RPT button on the COMAND System. A pop-up window will ap- pear in the COMAND System display to indicate that a Tele Aid call is in progress. After the Tele Aid call has ended, the optional cellular phone switches on again. A PIN entry might be neces- sary.

System self-check Initially, after switching on ignition, mal- functions are detected and indicated (the indicator lamps in the SOS button, the Roadside Assistance button • and the Information button ¡ stay on longer than 10 seconds or do not come on). The message Malfunction Service Required appears in the multifunction display.

Warning!

If the indicator lamps on the SOS button, on the Roadside Assistance button, and/or on the Information button remain illuminated continuously in red and/or the message Malfunction Service Required is displayed in the multifunction display after the system self-check, a malfunction in the system has been detected.

If a malfunction is indicated as outlined above, the system may not operate as expected. Have the system checked at the nearest Mercedes-Benz Center as soon as possible.

Emergency calls An emergency call is initiated automatical- ly following an accident in which the emer- gency tensioning devices (ETDs) or air bags deploy. An emergency call can also be initiated manually by opening the cover next to the interior rear view mirror labeled SOS, then briefly pressing the button located under the cover. See (컄 page 258) for instructions on initiating an emergency call manually. Once the emergency call is in progress, the indicator lamp on the SOS button will begin to flash. The message Connecting Call appears in the multi- function display. When the connection is established, the message Call Connected appears in the multifunction display. All in- formation relevant to the emergency, such as the location of the vehicle (determined by the GPS satellite location system), vehi- cle model, identification number and color are generated.

257

Controls in detail Useful features

A voice connection between the Response Center and the occupants of the vehicle will be established automatically soon af- ter the emergency call has been initiated. The Response Center will attempt to determine more precisely the nature of the accident provided they can speak to an occupant of the vehicle. The Tele Aid system is available if 앫 it has been activated and is operation- al. Activation requires a subscription for monitoring services, connection and cellular air time

앫 the relevant cellular phone network

and GPS signals are available and pass the information on to the response cen- ter

i Location of the vehicle on a map is only pos- sible if the vehicle is able to receive signals from the GPS satellite network and pass the informa- tion on to the Response Center.

Warning!

If the indicator lamp in the SOS button is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an emergency call (e.g. the rele- vant cellular phone network is not available). The message Call Failed appears in the multifunction display for approximately 10 seconds.

Should this occur, assistance must be sum- moned by other means.

258

Initiating an emergency call manually

1 Cover 2 SOS button 왘 Briefly press on cover 1.

The cover will open.

왘 Press SOS button 2 briefly.

The indicator lamp in SOS button 2 will flash until the emergency call is concluded.

왘 Wait for a voice connection to the

Response Center.

왘 Close cover 1 after the emergency

call is concluded.

Warning!

If you feel at any way in jeopardy when in the vehicle (e.g. smoke or fire in the vehicle, vehicle in a dangerous road location), please do not wait for voice contact after you have pressed the emergency button. Carefully leave the vehicle and move to a safe loca- tion. The Response Center will automatically contact local emergency officials with the vehicle’s approximate location if they re- ceive an automatic SOS signal and cannot make voice contact with the vehicle occu- pants.

Roadside Assistance button • The Roadside Assistance button • is located below the center armrest cover. 왘 Open the storage compartment under

the center armrest (컄 page 243).

왘 Press and hold button (for longer than

2 seconds). A call to a Mercedes-Benz Roadside Assistance dispatcher will be initiated. The button will flash while the call is in progress. The message Connecting Call will appear in the multifunction display.

When the connection is established, the message Call Connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and location (subject to availability of cellular and GPS signals).

i While the call is connected you can change to the navigation menu by pressing NAVI button on the COMAND System unit.

Controls in detail Useful features

A voice connection between the Roadside Assistance dispatcher and the occupants of the vehicle will be established. 왘 Describe the nature of the need for

assistance.

The Mercedes-Benz Roadside Assistance dispatcher will either dispatch a qualified Mercedes-Benz technician or arrange to tow your vehicle to the nearest Mercedes-Benz Center. For services such as labor and/or towing, charges may ap- ply. Refer to the Roadside Assistance Man- ual for more information. These programs are only available in the USA: 앫 Sign and Drive services: Services such as jump start, a few gallons of fuel or the replacement of a flat tire with the vehicle spare tire are obtainable.

259

Controls in detail Useful features

i The indicator lamp on the Roadside Assistance button • remains illuminated in red for approximately 10 seconds during the sys- tem self-check after switching on the ignition (to- gether with the SOS button and the Information button ¡). See system self-check (컄 page 257) if the indi- cator lamp does not come on in red or stays on longer than approximately 10 seconds. If the indicator lamp on the Roadside Assistance button • is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate a Roadside Assistance call (e.g. the rele- vant cellular phone network was not available). The message Call Failed appears in the mul- tifunction display. Roadside Assistance calls can be terminated us- ing the t button on the multifunction steer- ing wheel or the END Button on the COMAND System.

260

Information button ¡ The Information button ¡ is located below the center armrest cover. 왘 Open the storage compartment under

the center armrest (컄 page 243).

왘 Press and hold button (for longer than

2 seconds). A call to the Customer Assistance Center will be initiated. The button will flash while the call is in progress. The message Connecting Call will appear in the multifunction display.

When the connection is established, the message Call Connected appears in the multifunction display. The Tele Aid system will transmit data generating the vehicle identification number, model, color and lo- cation (subject to availability of cellular and GPS signals).

i While the call is connected, you can change to the navigation menu by pressing NAVI button on the COMAND System.

A voice connection between the Customer Assistance Center representative and the occupants of the vehicle will be estab- lished. Information regarding the operation of your vehicle, the nearest Mercedes-Benz Center or Mercedes-Benz USA products and services is available to you. For more details concerning the Tele Aid system, please visit www.mbusa.com and use your ID and password (sent to you sep- arately) to learn more (USA only).

i The indicator lamp in the Information button ¡ remains illuminated in red for ap- proximately 10 seconds during the system self-check after switching on the ignition (togeth- er with the SOS button and the Roadside Assistance button •). See system self-check (컄 page 257) if the indi- cator lamp does not come on in red or stays on longer than approximately 10 seconds.

If the indicator lamp in the Information button ¡ is flashing continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an Information call (e.g. the relevant cel- lular phone network is not available). The mes- sage Call Failed appears in the multifunction display. Information calls can be terminated using the t button on the multifunction steering wheel or the END Button on the COMAND Sys- tem. ! If the indicator lamps do not start flashing after pressing one of the buttons or remain illu- minated (in red) at any time, the Tele Aid system has detected a malfunction or the service is not currently active, and may not initiate a call. Con- tact your authorized Mercedes-Benz Center and have the system checked or contact the Re- sponse Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada) as soon as pos- sible.

Call priority If other service calls such as a Roadside Assistance call or Information call are active, an Emergency call is still possible. In this case, the Emergency call will take priority and override all other active calls.

i The indicator lamp in the respective button flashes until the call is concluded. Emergency calls can only be terminated by a Response Cen- ter or Customer Assistance Center representa- tive, whereas Roadside Assistance and Information calls can also be terminated by pressing button t on the multifunction steer- ing wheel or using the END button on the COMAND System.

! If the indicator lamp continues to flash or the system does not reset, contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada), or Mercedes-Benz Customer Assistance at 1-800-FOR-MERCedes (1-800-367-6372) in the USA or Customer Ser- vice at 1-800-387-0100 in Canada.

Controls in detail Useful features

Remote door unlock In case you have locked your vehicle unin- tentionally (e.g. SmartKey inside vehicle), and the reserve SmartKey is not handy: 왘 Contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your pass- word which you provided when you completed the subscriber agreement. 왘 Then return to your vehicle and pull the tailgate recessed handle for minimum of 20 seconds until the SOS button is flashing. The message Connecting Call ap- pears in the multifunction display.

As an alternative, you may unlock the vehi- cle via Internet using the ID and password sent to you shortly after the completion of your acquaintance call. The Response Center will then unlock your vehicle with the remote door unlocking feature.

261

Controls in detail Useful features

i The remote door unlock feature is available if the relevant cellular phone network is avail- able. The SOS button will flash and the message Connecting Call will appear in the multifunc- tion display to indicate receipt of the door unlock command. Once the vehicle is unlocked, a Response Center specialist may attempt to establish voice contact with the vehicle occupants. If the tailgate recessed handle was pulled for more than 20 seconds before door unlock autho- rization was received by the Response Center, you must wait 15 minutes before pulling the tail- gate recessed handle again.

262

Garage door opener

The integrated remote control is capable of operating up to three separately controlled devices. It provides a convenient way to re- place up to three hand-held remote con- trols used to operate devices such as garage door openers, gate openers, or oth- er devices compatible with HomeLink® or some other systems. Before the integrated remote control can be used, it must be programmed to the ga- rage door opener, gate operator or other device you wish to operate. See the follow- ing instructions for programming informa- tion.

Stolen Vehicle Recovery services In the event your vehicle was stolen: 왘 Report the incident to the police. The police will issue a numbered incident report.

왘 Pass this number on to the

Mercedes-Benz Response Center along with your password issued to you when you subscribed to the service. The Response Center will then attempt to covertly contact the vehicle’s Tele Aid system. Once the vehicle is located, the Response Center will contact the local law enforcement and you. The vehicle’s location will only be provided to law enforcement.

i When the anti-theft alarm or the tow-away alarm stays on for more than 30 seconds, a call is initiated automatically to the Response Cen- ter. See anti-theft alarm system (컄 page 97).

Warning!

Before programming the integrated remote control to a garage door opener or gate operator, make sure people and objects are out of the way of the device to prevent po- tential harm or damage. When programming a garage door opener, the door moves up or down. When programming a gate operator, the gate opens or closes.

Do not use the integrated remote control with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object – signaling the door to stop and reverse – does not meet current U.S. federal safety standards.

When programming a garage door opener, park the vehicle outside the garage.

Indicator lamp

Interior rear view mirror with integrated re- mote control 2 3 4 Signal transmitter button Needed for programming (not part of vehi- cle equipment):

Hand-held remote control of ga- rage door opener, gate operator or other device Hand-held remote control but- ton

Controls in detail Useful features

Do not run the engine while programming the integrated remote control. Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause unconsciousness and possible death.

Programming integrated remote control Step 1: 왘 Switch on the ignition (컄 page 38).

컄컄

263

Controls in detail Useful features

컄컄

Step 2: 왘 If you have previously programmed a signal transmitter button and wish to retain its programming, proceed to step 3. If you are programming the integrated remote control for the first time, press and hold the two outer signal transmit- ter buttons 2 and 4 and release them only when indicator lamp 1 be- gins to flash after approximately 20 seconds (do not hold the button for longer than 30 seconds). This proce- dure erases any previous settings for all three channels and initializes the memory. If you later wish to program a second and/or third hand-held transmitter to the remaining two signal transmitter buttons, do not repeat this step and be- gin directly with step 3.

Step 3: 왘 Hold the end of hand-held remote

control 5 of the device you wish to train approximately 2 to 5 in (5 to12 cm) away from the signal trans- mitter button (2, 3 or 4) to be pro- grammed, while keeping indicator lamp 1 in view.

Step 4: 왘 Using both hands, simultaneously

press hand-held remote control button 6 and the desired signal trans- mitter button (2, 3 or 4). Do not release the buttons until step 5 is com- pleted. Indicator lamp 1 will flash, first slowly and then rapidly.

i Indicator lamp 1 flashes immediately the first time the signal transmitter button is pro- grammed. If this button has already been pro- grammed, the indicator lamp will only start flashing after 20 seconds.

Step 5: 왘 After indicator lamp 1 changes from a slow to a rapidly flashing light, release the hand-held remote control button and the signal transmitter button.

Step 6: 왘 Press and hold the just-trained signal transmitter button (2, 3 or 4) and observe indicator lamp 1. If indicator lamp 1 stays on constantly, programming is complete and your device should activate when the respective signal transmitter button (2, 3 or 4) is pressed and re- leased.

i If indicator lamp 1 flashes rapidly for about 2 seconds and then turns to a constant light, continue with programming steps 8 through 12 as your garage door opener may be equipped with the “rolling code” feature.

Step 7: 왘 To program the remaining two signal transmitter buttons, repeat the steps above starting with step 3.

264

Rolling code programming To train a garage door opener (or other rolling code devices) with the rolling code feature, follow these instructions after completing the “Programming” portion (steps 1 through 6) of this text. (A second person may make the following training procedures quicker and easier.) Step 8: 왘 Locate “training” button on the garage

door opener motor head unit. Exact location and color of the button may vary by garage door opener brand. Depending on manufacturer, the “training” button may also be referred to as “learn”or “smart” button. If there is difficulty locating the transmitting button, refer to the garage door opener operator’s manual.

Step 9: 왘 Press the “training” button on the ga-

rage door opener motor head unit. The “training light” is activated.

You have 30 seconds to initiate the follow- ing two steps. Step 10: 왘 Return to the vehicle and firmly press, hold for 2 seconds and release the pro- grammed signal transmitter button (2, 3 or 4).

Step 11: 왘 Press, hold for 2 seconds and release same signal transmitter button a sec- ond time to complete the training pro- cess.

i Some garage door openers (or other rolling code equipped devices) may require you to press, hold for 2 seconds and release the same signal transmitter button a third time to com- plete the training process.

Step 12: 왘 Confirm the garage door operation by pressing the programmed signal trans- mitter button (2, 3 or 4).

Controls in detail Useful features

Step 13: 왘 To program the remaining two signal transmitter buttons, repeat the steps above starting with step 3.

Gate operator/Canadian programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission which may not be long enough for the integrated signal transmitter to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. If you live in Canada or if you are having difficulties programming a gate operator (regardless of where you live) by using the programming procedures, replace step 4 with the following:

265

Controls in detail Useful features

Step 4: 왘 Press and hold the signal transmitter button (2, 3 or 4). Do not release this button until it has been successful- ly trained.

왘 While still holding down the signal transmitter button (2, 3 or 4), “cycle” your hand-held remote control button 6 as follows: Press and hold button 6 for 2 seconds, then release it for 2 seconds, and again press and hold it for 2 seconds. Repeat this se- quence on the hand-held remote con- trol until the frequency signal has been learned. Upon successful training, indi- cator lamp 1 will flash slowly and then rapidly after several seconds.

왘 Proceed with programming step 5 and

step 6 to complete.

266

i Upon completion of programming the inte- grated remote control, make sure you retain the hand-held remote control that came with the ga- rage door opener, gate operator or other device. You may need it for use in other vehicles, for fu- ture programming of an integrated remote con- trol, or simply for continued use as a hand-held remote control to operate the respective device in other situations.

Reprogramming a single signal trans- mitter button To program a device using a signal trans- mitter button previously trained, follow these steps: 왘 Switch on the ignition (컄 page 38). 왘 Press and hold the desired signal transmitter button (2, 3 or 4). Do not release the button.

왘 Indicator lamp 1 will begin to flash af- ter 20 seconds. Without releasing the signal transmitter button, proceed with programming starting with step 3.

Operation of integrated remote control 왘 Switch on the ignition (컄 page 38). 왘 Select and press the appropriate inte- grated signal transmitter button (2, 3 or 4) to activate the remote con- trolled device. The integrated remote control trans- mitter continues to send the signal as long as the button is pressed – up to 20 seconds.

Erasing integrated remote control memory 왘 Switch on the ignition (컄 page 38). 왘 Simultaneously press and hold outer signal transmitter buttons 2 and 4, for approximately 20 seconds, until indicator lamp 1 flashes rapidly. Do not hold for longer than 30 seconds. The codes of all three channels are erased.

i If you sell your vehicle, erase the codes of all three channels.

Programming tips If you are having difficulty programming the integrated remote control, here are some helpful tips: 앫 Check the frequency of hand-held re- mote control 5 (typically located on the reverse side of the remote). The in- tegrated remote control is compatible with radio-frequency devices operating between 280-390 MHz.

앫 Put a new battery in hand-held remote control 5. This will increase the likeli- hood of the hand-held remote control sending a faster and more accurate sig- nal to the integrated remote control.

앫 While performing step 3, hold

hand-held remote control 5 at differ- ent lengths and angles from the signal transmitter button (2, 3 or 4) you are programming. Attempt varying an- gles at the distance of 2 to 5 in (5 to 12 cm) away or the same angle at vary- ing distances.

앫 If another hand-held remote control is available for the same device, try the programming steps again using that other hand-held remote control. Make sure new batteries are in the hand-held remote control before beginning the procedure.

앫 Straighten the antenna wire from the

garage door opener assembly. This may help improve transmitting and/or receiving signals.

i Certain types of garage door openers are in- compatible with the integrated remote control. If you should experience further difficulties with programming the integrated remote control, contact an authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Cen- ter (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.

Controls in detail Useful features

i USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer-

ence, and

(2) this device must accept any interference re-

ceived, including interference that may cause undesired operation.

Any unauthorized modification to this device could void the user’s authority to operate the equipment.

i Canada only: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undesired operation of the device. Any unauthorized modification to this device could void the user’s authority to operate the equipment.

267

268

Operation

The first 1000 miles (1500 km) Driving instructions At the gas station Engine compartment Tires and wheels Winter driving Maintenance Vehicle care

269

Operation The first 1000 miles (1500 km)

In the “Operation” section you will find de- tailed information on operating, maintain- ing and caring for your vehicle.

270

! Additional instructions for AMG vehicles: 앫 During the first 1000 miles (1500 km), do not exceed a speed of 85 mph (140 km/h).

앫 During this period, avoid engine speeds

above 4500 rpm in each gear.

All of the above instructions, as may apply to your vehicle type, also apply when driv- ing the first 1000 miles (1500 km) after the engine or the rear differential has been replaced.

i Always obey applicable speed limits.

The more cautiously you treat your vehicle during the break-in period, the more satis- fied you will be with its performance later on. 앫 Drive your vehicle during the first

1000 miles (1500 km) at varying but moderate vehicle and engine speeds. 앫 During this period, avoid heavy loads

(full throttle driving) and excessive engine speeds (no more than 2/3 of maximum rpm in each gear).

앫 Avoid accelerating by kickdown. 앫 Do not attempt to slow the vehicle

down by shifting to a lower gear using the gear selector lever.

앫 Select gear 3, 2 or 1 only when driving

at moderate speeds (for hill driving).

앫 Select C as the preferred shift program (컄 page 175) for the first 1000 miles (1500 km).

After 1000 miles (1500 km) you may grad- ually increase vehicle and engine speeds to the permissible maximum.

Operation Driving instructions

Drinking and driving

Pedals

Warning!

Warning!

Make sure that absolutely no objects are ob- structing the pedals range of movement. Keep the driver’s footwell clear of all obsta- cles. If there are any floormats or carpets in the footwell, make sure that the pedals still have sufficient clearance.

Drinking and driving and/or taking drugs and driving are very dangerous combina- tions. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgment.

The possibility of a serious or even fatal ac- cident are greatly increased when you drink or take drugs and drive.

Do not drink or take drugs and drive or allow anyone to drive who has been drinking or taking drugs.

왔 Driving instructions Drive sensibly – save fuel

Fuel consumption, to a great extent, de- pends on driving habits and operating con- ditions. To save fuel you should: 앫 Keep tires at the recommended infla-

tion pressures.

앫 Remove unnecessary loads. 앫 Remove roof rack when not in use. 앫 Allow engine to warm up under low

load use.

앫 Avoid frequent acceleration and decel-

eration.

앫 Have all maintenance work performed at the intervals specified in the Mainte- nance Booklet and as required by the Maintenance System. Contact an authorized Mercedes-Benz Center.

Fuel consumption is also increased by driv- ing in cold weather, in stop-and-go traffic, on short trips and in hilly area.

271

Operation Driving instructions

Power assistance

Brakes

Warning!

Warning!

With the engine not running, there is no power assistance for the brake and steering systems. In this case, it is important to keep in mind that a considerably higher degree of effort is necessary to brake and steer the vehicle.

After driving in heavy rain for some time without applying the brakes or through wa- ter deep enough to wet brake components, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain expected braking ef- fect. Maintain a safe distance from vehicles in front.

Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads.

It can also result in the brakes overheating, thereby significantly reducing their effec- tiveness. It may not be possible to stop the vehicle in sufficient time to avoid an acci- dent.

! Because the ESP® operates automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO* start/stop button in position 0 or 1) when testing the brakes on a brake test dy- namometer and such testing should be no longer than 10 seconds. Active braking action through ESP® may other- wise seriously damage the brake system which is not covered by the Mercedes-Benz Limited War- ranty.

To help prevent brake disk corrosion after driving on wet road surfaces (particularly salted roads), it is advisable to brake the vehicle with considerable force prior to parking. The heat generated serves to dry the brakes. If your brake system is normally only sub- jected to moderate loads, you should occa- sionally test the effectiveness of the brakes by applying above-normal braking pressure at higher speeds. This will also enhance the grip of the brake pads.

272

Warning!

Make sure not to endanger any other road users when carrying out these braking ma- neuvers.

Refer to the description of the Brake Assist System (BAS) (컄 page 90).

Operation Driving instructions

Brake pad wear or a leak in the system may be the reason for low brake fluid in the res- ervoir. The brake fluid level in the reservoir may be too low if the brake warning lamp in the instrument cluster comes on and an acoustic warning sounds although the parking brake is released (컄 page 347). Observe additional messages in the multi- function display that may appear (컄 page 374). Have the brake system inspected immedi- ately. Contact an authorized Mercedes-Benz Center. All checks and service work on the brake system should be carried out by qualified technicians only. Contact an authorized Mercedes-Benz Center. Only install brake pads and brake fluid recommended by Mercedes-Benz.

Warning!

If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired. This could result in an accident.

Be certain to read and observe the warning notices on brake pad replacement (컄 page 373).

! When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces brake pad wear.

After hard braking, it is advisable to drive on for some time, rather than immediately park, so that the air stream will cool down the brakes faster.

273

Operation Driving instructions

High-performance brake system (CLS 63 AMG only) The high-performance brake system is de- signed to operate under the extremely high operating demands required to accommo- date the performance capabilities of the vehicle. The brakes may produce a squeak- ing-type noise depending on the 앫 vehicle speed 앫 brake force applied 앫 ambient conditions, e.g. temperature

and humidity

As with any brake system, the wear of indi- vidual brake system components such as brake pads or disks strongly depends on your driving style and the conditions under which you operate the vehicle. Thus, a driv- ing style calling for high demand braking will cause your vehicle’s brakes to wear more quickly.

274

Warning!

Driving off

New vehicle brake pads and discs, and replacement brake pads and discs may take several hundred miles of driving until they provide optimum braking efficiency. Until that time, you may need to use increased brake pedal pressure while braking. Please be aware of this and adjust your driving and braking accordingly during this break-in period.

Excessive high demand braking will cause correspondingly high brake wear. Please be attentive to the brake warning lamp in the instrument cluster and brake condition mes- sages in the multifunction display. Especial- ly for high performance driving, it is important to maintain and have the brake system checked regularly.

Apply the brakes to test them briefly after driving off. Perform this procedure only when the road is clear of other traffic. Warm up the engine smoothly. Do not place full load on the engine until the oper- ating temperature has been reached. When starting off on a slippery surface, do not allow a drive wheel to spin for an ex- tended period with the ESP® switched off. Doing so may cause serious damage to the drive train which is not covered by the Mercedes-Benz Limited Warranty.

! When driving off on a slippery surface, do not allow a drive wheel to spin for an extended period with the ESP® switched off. Doing so may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited War- ranty.

! Simultaneously depressing the accelerator pedal and applying the brake reduces engine performance and causes premature brake and drivetrain wear.

Parking

Warning!

Do not park this vehicle in areas where com- bustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

To reduce the risk of personal injury, or damage to the vehicle drivetrain, as a result of vehicle movement, before turning off the engine and leaving the vehicle always: 앫 Keep right foot on brake pedal. 앫 Firmly depress parking brake pedal. 앫 Move the gear selector lever to

position P.

앫 Slowly release brake pedal.

앫 Slowly release brake pedal. 앫 When parked on an incline, turn front

wheel towards the road curb.

앫 Turn the SmartKey in the starter switch to position 0 and remove the SmartKey from the starter switch, or press KEYLESS-GO* start/stop button (vehi- cles with KEYLESS-GO*).

앫 Take the SmartKey or the SmartKey with KEYLESS-GO* with you and lock vehicle when leaving.

Tires

Warning!

If you feel a sudden significant vibration or ride disturbance, or you suspect that possi- ble damage to your vehicle has occurred, you should turn on the hazard warning flash- ers, carefully slow down, and drive with cau- tion to an area which is a safe distance from the road.

Operation Driving instructions

Inspect the tires and the vehicle underbody for possible damage. If the vehicle or tires appear unsafe, have the vehicle towed to the nearest Mercedes-Benz Center or tire dealer for repairs.

Treadwear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and become visible at a tread depth of approx- imately 1/16 in (1.6 mm), at which point the tire is considered worn and should be re- placed. The treadwear indicator appears as a solid band across the tread.

275

Operation Driving instructions

Warning!

Warning!

Tire traction

Although the applicable federal motor vehi- cle safety laws consider a tire to be worn when the treadwear indicators (TWI) be- come visible at approximately 1/16 in (1.6 mm), we recommend that you do not allow your tires to wear down to that level. As tread depth approaches 1/8 in (3 mm), the adhesion properties on a wet road are sharply reduced.

Depending upon the weather and/or road surface (conditions), the tire traction varies widely.

Specified tire inflation pressures must be maintained. This applies particularly if the tires are subjected to high loads (e.g. high speeds, heavy loads, high ambient temper- atures).

Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build-up and possibly a fire.

For more information, see “Tires and wheels” (컄 page 293).

Hydroplaning

Depending on the depth of the water layer on the road, hydroplaning may occur, even at low speeds and with new tires. Reduce vehicle speed, avoid track grooves in the road and apply brakes cautiously in the rain.

The safe speed on a wet, snow covered or icy road is always lower than on a dry road. You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point.

Warning!

If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution.

276

Operation Driving instructions

Mercedes-Benz recommends winter tires (컄 page 328) with a minimum tread depth of approximately 1/6 in (4 mm) on all four wheels for the winter season to make sure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance compared to summer tires. Stopping distance, however, is still considerably greater than when the road is not covered with snow or ice. Exercise appropriate caution.

! Avoid spinning of a drive wheel. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited War- ranty.

Tire speed rating

Regardless of the tire speed rating, local speed limits should be obeyed. Use pru- dent driving speeds appropriate to prevail- ing conditions.

Warning!

Even when permitted by law, never operate a vehicle at speeds greater than the maxi- mum speed rating of the tires.

Exceeding the maximum speed for which tires are rated can lead to sudden tire fail- ure, causing loss of vehicle control and pos- sibly resulting in an accident and/or personal injury and possible death, for you and for others.

An electronic speed limiter prevents your vehicle from exceeding a speed of: 앫 CLS 550

CLS 550 (Sport Package*): 130 mph (210 km/h)

앫 CLS 63 AMG:

155 mph (250 km/h)

앫 CLS 63 AMG (Performance Package*):

186 mph (300 km/h)

The factory equipped tires on your vehicle may have a tire speed rating above the maximum speed permitted by the elec- tronic speed limiter. Make sure your tires have the required tire speed rating as specified for your vehicle in the “Technical data” section (컄 page 438), for example when purchasing new tires.

277

Operation Driving instructions

For information on how to identify the tire speed rating on a tire’s sidewall, see “Tire size designation, load and speed rating” (컄 page 314). If you are uncertain about the correct read- ing of the information given on a tire’s side- wall, any authorized Mercedes-Benz Center will be glad to assist you.

i For information on speed rating for winter tires, see “Winter driving” (컄 page 328). For additional general information on tire speed markings on tire sidewall, see “Tire speed rating” (컄 page 316).

Winter driving instructions

The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move gear selector lever to position N. Try to keep the vehicle under control by cor- rective steering action.

i For more information on driving with snow chains, see “Snow chains” (컄 page 329).

Warning!

On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehi- cle control. Your vehicle’s ABS will not pre- vent this type of control loss.

Road salts and chemicals can adversely affect braking efficiency. Increased pedal force may become necessary to produce the normal braking effect. Depressing the brake pedal periodically when traveling at length on salt-strewn roads can bring road-salt-impaired braking efficiency back to normal. If the vehicle is parked after being driven on salt-treated roads, the braking efficien- cy should be tested as soon as possible after driving is resumed.

278

Operation Driving instructions

Warning!

Warning!

Standing water

Make sure not to endanger any other road users when carrying out these braking ma- neuvers.

Warning!

If the vehicle becomes stuck in snow, make sure that snow is kept clear of the exhaust pipe and from around the vehicle with the engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and possible death.

To assure sufficient fresh air ventilation, open a window slightly on the side of the ve- hicle not facing the wind.

The outside temperature indicator is not de- signed to serve as an ice-warning device and is therefore unsuitable for that purpose. Indicated temperatures just above the freez- ing point do not guarantee that the road sur- face is free of ice.

For more information, see “Winter driving” (컄 page 328).

! Do not drive through flooded areas or water of unknown depth. Before driving through water, determine its depth. Never accelerate before driving into water. The bow wave could force wa- ter into the engine and auxiliary equipment, thus damaging them. If you must drive through standing water, drive slowly to prevent water from entering the pas- senger compartment or the engine compart- ment. Water in these areas could cause damage to electrical components or wiring of the engine or transmission, or could result in water being in- gested by the engine through the air intake caus- ing severe internal engine damage. Any such damage is not covered by the Mercedes-Benz Limited Warranty.

279

Operation Driving instructions

Passenger compartment

Warning!

Always fasten items being carried as secure- ly as possible.

In an accident, during hard braking or sud- den maneuvers, loose items will be thrown around inside the vehicle, and cause injury to vehicle occupants unless the items are securely fastened in the vehicle.

The trunk is the preferred place to carry objects.

Driving abroad

Abroad, there is an extensive Mercedes-Benz service network at your disposal. If you plan to drive into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from your authorized Mercedes-Benz Center.

280

Control and operation of radio transmitter

COMAND, radio and telephone*

Warning!

Please do not forget that your primary re- sponsibility is to drive the vehicle safely. Only operate the COMAND (Cockpit Management and Data System), radio or telephone1 if road, weather and traffic con- ditions permit.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

1 Observe all legal requirements.

Telephones and two-way radios

Warning!

Never operate radio transmitters equipped with a built-in or attached antenna (i.e. with- out being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunc- tion of the vehicle’s electronic system, pos- sibly resulting in an accident and/or personal injury.

Radio transmitters, such as a portable tele- phone or a citizens band unit should only be used inside the vehicle if they are con- nected to an antenna that is installed on the outside of the vehicle. Refer to the radio transmitter operation instructions regarding use of an external antenna.

Operation Driving instructions

Catalytic converter

Your Mercedes-Benz is equipped with monolithic-type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions. Keep your vehicle in proper operating condition by following our rec- ommended maintenance instructions as outlined in your Maintenance Booklet.

! To prevent damage to the catalytic convert- ers, only use premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, exces- sive unburned fuel may reach the catalytic con- verter, causing it to overheat, which could potentially start a fire.

Warning!

As with any vehicle, do not idle, park or operate this vehicle in areas where combus- tible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Emission control

Certain parts of the engine and the emis- sion control system serve to keep the toxic components of the exhaust gases within permissible limits required by law. These systems will function properly only when maintained strictly according to fac- tory specifications. Any adjustments on the engine should, therefore, be carried out only by qualified Mercedes-Benz Cen- ter authorized technicians.

Engine adjustments should not be altered in any way. Moreover, the specified service procedures must be carried out regularly according to Mercedes-Benz servicing requirements. For details refer to the Maintenance Booklet.

Warning!

Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide (CO), and inhaling it can cause un- consciousness and possible death.

Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one win- dow fully open at all times.

281

Operation Driving instructions

Coolant temperature

During severe operating conditions and stop-and-go city traffic, the coolant tem- perature may rise close to approximately 248°F (120°C). The engine should not be operated with the coolant temperature over 248°F (120°C). Doing so may cause serious engine damage which is not covered by the Mercedes-Benz Limited Warranty.

Warning!

앫 Driving when your engine is badly over-

heated can cause some fluids, which may have leaked into the engine com- partment, to catch fire. You could be seriously burned.

앫 Steam from an overheated engine can cause serious burns and can occur just by opening the engine hood. Stay away from the engine if you see or hear steam coming from it.

Turn off the engine, get out of the vehicle and do not stand near the vehicle until the engine has cooled down.

282

왔 At the gas station Refueling

Warning!

Gasoline is highly flammable and poisonous. It burns violently and can cause serious per- sonal injury.

Never allow sparks, flame or smoking mate- rials near gasoline!

Turn off the engine before refueling.

Whenever you are around gasoline, avoid in- haling fumes and skin or clothing contact, extinguish all smoking materials.

Direct skin contact with fuels and the inha- lation of fuel vapors can damage your health.

! Damage resulting from the use of non ap- proved fuels or fuel additives or resulting from mixing gasoline with diesel fuel is not covered by the Mercedes-Benz Limited Warranty.

The fuel filler flap is located on the right-hand side of the vehicle towards the rear. Locking/unlocking the vehicle with the remote control automatically locks/unlocks the fuel filler flap.

i In case that the central locking system does not release the fuel filler flap, or the opening mechanism is clamping, notify Roadside Assis- tance or an authorized Mercedes-Benz Center.

Operation At the gas station

1 Fuel filler flap 2 Fuel filler cap 3 Holder 왘 Turn the engine off. 왘 Vehicles with SmartKey: Remove the

SmartKey from the starter switch. Vehicles with KEYLESS-GO*: Open the driver’s door (this puts the starter switch in position 0, same as with the SmartKey removed from the starter switch). The driver’s door then can be closed again.