Login- Download PDF Manual
-
Instrument cluster display
Practical hints
Car care
Technical
data
Index
133
J_C208_II.book Seite 134 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
134
Fader1
Centering all audio functions
Press the AUD key repeatedly until “FADER” appears on the display. Press the “R” key to move the sound to the rear speakers or the “F” key to
move the sound to the front speakers.
Push and hold down the “AUD” key. All audio functions (bass, treble, balance and fader) are set to center or flat positions, and
the volume is adjusted to a pre-set level.
Balance
Press the AUD key repeatedly until “BALANCE” appears in the display. Press the “L” key to move the
sound to the left speaker or the “R” key to move the sound to the right speaker.
1 not available on all models
J_C208_II.book Seite 135 Donnerstag, 31. Mai 2001 10:13 10
Radio mode
Selecting radio mode Press
button.
Selecting the band
Manual tuning
or
Press either the
button. Step-by-step tuning in ascending or descending order of frequency will take place.
Press the key located below the desired band. The band selected is shown in the top line of the display.
The first three tuning steps will take place without muting. The radio will then be muted and high-speed tuning will take place until the button is released. The following tuning intervals will be shown on the display:
FM AM WB
200 kHz 10 kHz Channels 1-7
Frequency ranges:
FM AM WB
87.9 - 107.9 MHz 530 - 1710 kHz approx. 162 MHz
Seek tuning Press either the to the next receivable station.
or
button. The radio will tune
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
135
J_C208_II.book Seite 136 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Scan tuning
Press the SC key. Each strong receivable station on the band selected will be tuned in for 8 seconds. The first scan will tune only the stations with a high signal strength. The second scan will tune every receivable station. By pressing either the buttons, or the “SC” key the scan mode
or
can be cancelled.
136
Storing stations Hold the number button down for approximately 2 seconds. The currently displayed frequency is stored on the selected station button. The storage procedure is confirmed by a short signal tone.
Retrieving a station from memory Press the desired station button.
Station memory
Ten stations can be stored in the AM and FM bands via the alpha-numeric keypad. The “0” button corresponds to location 10. Weatherband (WB) channels 1 to 7 can be retrieved via the alpha- numeric keypad and are preset at the factory.
Direct frequency input (AM and FM only)
Select the band. Press the “ button and enter the desired frequency using the alpha-numeric keypad. Frequencies outside of the frequency ranges (frequencies specified on page 135) will not be accepted. The frequency input mode is cancelled if no button is pressed within 4 seconds.
J_C208_II.book Seite 137 Donnerstag, 31. Mai 2001 10:13 10
Cassette mode
Note: Vehicles equipped with the COMAND system do not come with a factory installed cassette mechanism. A standard 1/8” stereo phono plug for auxiliary audio input (located in glove box) is provided for connection of a portable battery operated cassette player or any other portable device which uses a headphone output. Please refer to the COMAND operating manual for information concerning the activation of the audio input.
Playing cassettes Press the “TAPE” button. When the eject (EJ) key is pressed, the display folds down and the cassette slot becomes visible. Push the cassette into the slot until it engages. The cassette will be pulled in automatically.
Notes: Do not press directly on the radio display face. Return the display panel to its normal position by folding it back up and pressing gently on the display frame to lock in place.
When playing mono recorded tapes (e.g. books) through a stereo system the sound from one track might bleed to the other track, despite setting the balance to the full left or full right speakers.
Important! If the display is in the down position for more than 20 seconds, 2 successive beeps will be heard. This will continue at 5 second intervals until the display is returned to its normal position.
The radio will switch to cassette mode. Track 1 will be played and “SIDE 1” displayed. Track 1 is the side of the cassette which is facing upwards. The cassette deck will automatically detect the type of tape and switch the equalization automatically. A cassette symbol in the display indicates that a tape is in the mechanism. This symbol appears in all modes but not in cassette mode. The cassette will not be ejected when the radio is switched off or another mode is selected.
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
137
J_C208_II.book Seite 138 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
138
Track selection
If a cassette is in the mechanism, cassette mode can be selected by using the “TAPE” button. If no cassette has been inserted, the display will show “NO TAPE”.
Press the track selection (TRK) key. The current track will be displayed as “SIDE 1” or “SIDE 2”. The track will be changed automatically at the end of the tape.
Cassette eject Press the eject (EJ) key. The display will fold down and the cassette will be ejected. Remove the cassette, then fold the display back up manually. The radio will switch back to radio mode automatically.
Note: The cassette will not be ejected when the radio is switched off.
Important! If the display is in the down position for more than 20 seconds, 2 successive beeps will be heard. This will continue at 5 second intervals until the display is returned to its normal position.
button.
Track search forwards/backwards Press the “SEEK FWD” will be shown on the display and the track search will run the tape forwards to the start of the next track. Press the “SEEK RWD” will be shown on the display and the track search will run the tape backwards to the start of the track currently playing. Track search can be interrupted by pressing the same button again.
button.
J_C208_II.book Seite 139 Donnerstag, 31. Mai 2001 10:13 10
Note: The beginning of a track can only be located if there is a break of at least 4 seconds between tracks.
Scanning
Fast forward/reverse
button.
Press the “FORWARD” will appear on the display and fast forward will start. Press the “REWIND” will appear on the display and fast reverse will start.
button.
Fast forward/reverse is stopped by pressing the same button again, or it will stop automatically at the beginning or the end of the tape. The track will automatically change at the end or beginning of the tape and play will begin.
Press the “SC” key. Each track on the cassette will be played for 8 seconds in ascending order.
Note: The beginning of a track can only be located if there is a break of at least 4 seconds between tracks. Scan will be interrupted if the buttons or the “SC” key is pressed.
Dolby NR1 (noise reduction system)
To enable optimum reproduction of cassettes recorded using the Dolby B system, press the “AUD” key followed by the NR key so the
“NR” in the display is not highlighted. To turn off Dolby B noise reduction, press the “NR” key so the “NR” in the display is highlighted.
1 Dolby and the double-D symbol Ù are trademarks of Dolby laboratories Licensing Corporation. The Dolby noise reduction system is manufactured under licence from Dolby Laboratories Licensing Corporation.
139
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 140 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
CD mode
General notes on CD mode Should excessive temperatures occur while in CD mode, “TEMP HIGH” will appear in the display and muting will take place. The unit will then switch back to radio mode until the temperature has decreased to a safe operating level. Should temperatures occur while in CD mode which are too low, “TEMP LOW” will be displayed, but the CD will play. It will be sensitive to skipping if you are driving over rough roads. Handle CDs carefully to prevent interference during playback. Avoid fingerprints and dust on CDs. Do not write on the CDs or apply any label to the CDs. Clean CDs from time to time with a commercially available cleaning cloth. No solvents, anti-static sprays, etc. should be used. Replace the CD in its container after use. Protect CDs from heat and direct sunlight.
140
Only use CDs, which bear the label shown and that conform to the compact disc digital audio standard (IEC 60908). Use of CDs which do not meet this standard may cause damage to the
CD changer. Do not play single-CDs (80 mm) with an adapter.
Warning! The CD changer1 is a Class 1 laser product. There is a danger of invisible laser radiation if the cover is opened or damaged. Do not remove the cover. The CD changer1 does not contain any parts which can be serviced by the user. For safety reasons, have any service work which may be necessary performed only by qualified personnel.
1 Optional equipment
J_C208_II.book Seite 141 Donnerstag, 31. Mai 2001 10:13 10
CD changer installed
Loading/emptying the CD magazine Slide the changer door to the right and press the eject button . The magazine will be ejected. Remove the magazine. Pull out the CD tray until its stop is reached and place the CDs in the recess of the tray, label side up. Push the tray into the magazine in the direction shown by the arrow. Insert the loaded magazine into the changer.
Important! Close the door after the magazine has been inserted.
1 CD changer1 2 CD magazine 3 CD tray 4 CD If a CD changer1 is installed, it can be operated from the front control panel of the radio. A loaded magazine must be installed for CD playing.
1 Optional equipment
Playing CDs Press the “CD” button. The CD most recently played will start at the point where it was last switched off. CDs stored in the magazine can be selected by using the station preset buttons 1-6.
The magazine slot number of the selected CD will then be displayed after “CD”. The number of the track being played will be displayed after “TRACK”.
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
141
J_C208_II.book Seite 142 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
142
If there is no CD in the selected magazine slot, “NO CD” and the corresponding slot number will be displayed
(e.g.“NO CD3”). After the last track on a CD has been played, the next CD will automatically be selected and played.
button. The next track on the CD will be
Skipping tracks forwards/backwards Press the played. Press the button. If the track has been playing for more than 10 seconds, it will revert to the start of that track. If it has been playing for less than ten seconds it will revert to the preceding track. To skip several tracks, the respective button must be pressed until the desired track is reached. If the beginning or end of the CD is reached during the search, the first or last track will be played.
Fast forward/reverse Press the forward. Press the reverse.
button and hold it down for audible fast
button and hold it down for audible
The search will stop when the button is released. The relative time of the track will be displayed during the search. The search mode will
cancel if the beginning or end of the CD is reached.
Scanning Press the SC key. Each track will be played for 8 seconds in ascending order. The search will stop at the track in question if the “SC” key is pressed.
buttons or the
J_C208_II.book Seite 143 Donnerstag, 31. Mai 2001 10:13 10
Random play/repeat function The tracks of the current CD are played in random order when the random feature (RDM) is selected. Press the RDM key to switch on, and press RDM again to switch off.
Direct track selection Tracks can be selected directly using the buttons on the alpha-numeric keypad. Press the “ function button, followed by the track number.
When the repeat function (RPT) has been selected, a particular track can be played for as many times as desired. Press the RPT key to switch
on, and press RPT again to switch off.
Note: Both functions cannot be used simultaneously.
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
143
J_C208_II.book Seite 144 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Telephone operation Various functions of the Mercedes-Benz integrated cellular telephone 1 can be performed and displayed via the car radio. Further instructions for operating the car telephone can be found in the operation guide for the cellular telephone 1.
Switching the telephone on and off
Switching on: Press the
button, “TEL” appears in the corner of the display. Switching off: Press and hold
button until the telephone symbol “TEL” no
the longer appears in the display, or press the “PWR” button on the phone’s keypad.
1 Optional equipment
144
Entering telephone number and starting dialing process
Enter the desired telephone number using the alpha- numeric keypad. The number can have up to 32 digits, but only 13 of these can be
displayed. The dialing process is started by pressing the SND button. The entered number can be corrected using the “CLR” key.
Press the CLR key briefly - and the last digit will be deleted. Press the CLR key longer - and
the complete number will be deleted.
Calling up the phone book The numbers stored in the telephone memory can be called up via either name or number entries. The memory contents from the portable phone must be downloaded and the telephone menu must be selected in order to call up the phone book. Refer to the “Memory download” section of the cellular telephone operation guide for more information.
J_C208_II.book Seite 145 Donnerstag, 31. Mai 2001 10:13 10
Switching between name search and number search Press ABC key - Name search Press NUM key - Number search
Placing a call
When a number or a name has been selected using the method described above, press the SND key.
Manual repeat dialing (redial) The last number entered can be re-selected by pressing the SND key once and the call can be placed by pressing the SND key a second time. The last dialed telephone number is shown on the display. Using the
button, the numbers stored in the re-dial
or
memory of the telephone can be selected.
The abbreviation L and the number in the memory are shown in the top line of the display.
Searching and selecting phone book entries by name Press the ABC key. The current name is shown on the display. The stored entries in alphabetical order can be selected using the button. By pressing the buttons, the stored entries can be selected
or
or
according to alphabetical initial letters (e.g. A-Adam, B-Brown, M-Miller).
Searching and selecting phone book entries by number Press the NUM key. The current number is shown on the display. The stored entries can be selected in numerical order using the pressing the can be selected in increments of 5 (e.g. Entry no. 2, Entry no. 7, etc.).
buttons, the stored entries
button. By
or
or
Audio system
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
145
J_C208_II.book Seite 146 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Audio system
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
146
Component malfunctions The radio, CD changer1, and Mercedes-Benz integrated cellular telephone1 are part of a fiberoptic networked system. Failure of one of the components can lead to malfunctions of the other components. Please contact your authorized Mercedes-Benz Center or call 1-800-FOR-MERCedes for more information in the event of a malfunction.
1 Optional equipment
Accepting incoming call in telephone mode With an incoming call, the ringing tone will be heard and the message “CALL” appears in the display. Press the SND key to answer the call.
Accepting incoming call in tape, CD or radio mode If the telephone is activated in the background (telephone symbol in the display), then a switch is made automatically to telephone when an incoming call is received. The audio source is muted, the ringing tone is heard and the message “CALL” appears. After the call has been terminated, the previously selected audio source is resumed.
Terminating call A current call can be terminated by pressing the END key.
J_C208_II.book Seite 147 Donnerstag, 31. Mai 2001 10:13 10
Power windows
Power window switches located on center console
P54.25-2031-26
Turn electronic key in steering lock to position 1 or 2. Press switch in to resistance point: k to open j to close
Release switch when window is in desired position.
Warning! When closing the windows, be sure that there is no danger of anyone being harmed by the closing procedure. In case of obstruction, the automatic reversal will not operate if a window is being closed by pressing the switch to its resistance point and holding it there, or when using the remote control. The closing procedure can be immediately reversed by either pressing the switch k or pressing button Πon the remote control, and holding it. When leaving the vehicle, always remove the electronic key from the steering lock, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment can cause serious personal injury.
Interior equipment
147
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 148 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
148
Express opening and closing of front door windows Press switch k or j past resistance point and release — window opens or closes completely. To interrupt procedure, briefly press k or j. If the upward movement of the window is blocked during the closing procedure, the window will stop during the last few inches before closure and open slightly. When pressing and holding the switch j to close the window, and upward movement of the window is blocked during the last few inches before closure, it will stop but not open slightly.
Warning! When leaving the vehicle, always remove the electronic key from the steering lock and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment can cause serious personal injury.
Note: The power windows can also be opened or closed with the infrared remote control while unlocking or locking the vehicle doors or trunk, see page 31. If the express closing function of the door windows is interrupted, press and hold the switch j to close the window completely. The automatic full closing procedure of the window should now be reactivated.
Synchronizing power windows If the power supply was interrupted (battery disconnected or low), the windows cannot be opened or closed by the express feature. To resynchronize the express feature, press j side of power window switch until the window is completely closed and hold for additional 2 seconds. Repeat procedure for each window. The automatic full opening and closing procedure of the windows should now be restored.
J_C208_II.book Seite 149 Donnerstag, 31. Mai 2001 10:13 10
Sliding/pop-up roof (optional on model CLK 430, standard on model CLK 55 AMG)
1 to slide roof open 2 to slide roof closed 3 to raise roof at rear 4 to lower roof at rear
Turn electronic key in steering lock to position 1 or 2. The switch is illuminated when the exterior lamps are switched on (except standing lamps).
Warning! When closing the sliding/pop-up roof, be sure that there is no danger of anyone being harmed by the closing procedure. The closing procedure can be immediately reversed by either moving the switch in direction (1) or (3) or pressing button Πon the remote control, and holding it.
Notes: The sliding/pop-up roof can be opened or closed manually should an electrical malfunction occur, see page 286. The sliding/pop-up roof can also be closed with the infrared remote control while locking the vehicle doors or trunk, see page 31.
Interior equipment
149
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 150 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
150
Synchronizing sliding/pop-up roof If the power supply was interrupted (battery disconnected or low), or if the sliding/pop-up roof is blocked during closing/opening procedure, the system has to be synchronized. To do so, turn electronic key in steering lock to position 2, move and hold switch in direction (3) until the sliding/pop-up roof is completely raised at rear, and hold for additional 1 second.
With the roof closed or tilted open, a screen can be slid into the roof opening to guard against sun rays. When sliding the roof open, the screen will also retract.
P68.00-2101-26
Express opening of sliding/pop-up roof Move switch past resistance point and release — the sliding/pop-up roof slides open automatically. To interrupt procedure, briefly move switch in any direction.
J_C208_II.book Seite 151 Donnerstag, 31. Mai 2001 10:13 10
Interior lighting
1 Automatic interior lighting
Press once and the automatic interior lighting is activated. Interior lamps are switched on, and off (soft fade) delayed, when unlocking or locking the vehicle, or when opening or closing a door. However, there will be no (soft fade) delay when the electronic key is in steering lock position 2. Press again and interior lamps remain switched off, even when centrally unlocking or opening a door.
Interior equipment
151
2 Press to switch interior and reading lamps on or off. 3 Press to switch rear passenger compartment lamp
on or off.
4 Press to switch reading lamp on or off.
Entrance lamps, exit lamps in doors The lamps are switched on and off by the door contact switches.
Note: To prevent the vehicle battery from being discharged, with doors open all interior lamps go out after approximately 5 minutes.
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 152 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
152
Rear window sunshade (optional on model CLK 430, standard CLK 55 AMG)
Sun visors
The switch is located on the center console. Turn electronic key in steering lock to position 1 or 2.
P54.25-2032-26
1 Hold to raise 2 Hold to lower
Always raise the sunshade fully for its support against the window frame.
Swing sun visors down to protect against sun glare. If sunlight enters through a side window, disengage visor from inner mounting, pivot it to the side, and slide it to the desired position.
J_C208_II.book Seite 153 Donnerstag, 31. Mai 2001 10:13 10
Illuminated vanity mirrors
Interior
Warning! To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things. Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs. Do not place anything on the shelf below the rear window. Luggage nets cannot secure hard or heavy objects.
Storage compartments, armrest and cup holder
Warning! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident and sudden maneuvers.
With the visor engaged in its inner mounting, the lamp is switched on by opening the cover.
Warning! Do not use the vanity mirror while driving.
The lamp goes out automatically after approximately 5 minutes.
Interior equipment
153
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 154 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
Glove box
154
Storage compartments in center console
P68.00-2067-26
1 Unlocking: Turn mechanical key to vertical position
and remove.
2 Locking: Turn mechanical key to the right and
remove.
3 Opening: Pull on handle.
The glove box can be locked and unlocked with the mechanical key. See page 25 for instructions on how to remove the mechanical key from the electronic key (e.g. for valet parking service).
To open compartment in armrest: Press button (4) and lift lid. To open compartment under armrest: Press button (5) and lift lid. To close: Lower lid until it engages in lock. To open cover: Touch top of cover (6) slightly. The cover opens automatically.
J_C208_II.book Seite 155 Donnerstag, 31. Mai 2001 10:13 10
Cup holder in center console
To open cup holder: Briefly press button (7). The cup holder opens automatically. To store cup holder: Push button (7) down until cup holder engages. Close cover (6).
Notes: The right claw is adjustable to accommodate most container sizes. An additional second (smaller size) container can be placed in the cup holder. Spilling liquids (e.g. soda or coffee) could restrict the movement of the claw. Refer to page 296 for cleaning the cup holder.
Caution! Keep cup holder closed while traveling. Place only containers that fit into the cup holder to prevent spills. Do not fill containers to a height where the contents could spill during vehicle maneuvers, especially hot liquids.
Interior equipment
155
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 156 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
156
Cup holder in rear bench armrest
Caution! Keep cup holders closed while traveling. Place only containers that fit into the cup holder to prevent spills. Do not fill containers to a height where the contents could spill during vehicle maneuvers, especially hot liquids.
Briefly press drawer (1) and pull out to its detent.
J_C208_II.book Seite 157 Donnerstag, 31. Mai 2001 10:13 10
Ashtrays
Center console, front By touching the bottom of the cover lightly, the ashtray opens automatically.
Prior to removing the ashtray insert, move the gear selector lever to position “N”.
Warning! Remove front ashtray only with vehicle standing still. With the gear selector lever in position “N”, turn off the engine and set the parking brake. Otherwise the vehicle might move as a result of unintended contact with the gear selector lever.
To remove ashtray: Push sliding knob (1) toward the right to eject the insert.
To install ashtray: Install insert into ashtray frame and push down to engage.
Interior equipment
157
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 158 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
Rear seats
158
To remove ashtray: Push cover (2) down and pull out insert (3).
To install ashtray: Push ashtray down to engage.
J_C208_II.book Seite 159 Donnerstag, 31. Mai 2001 10:13 10
Lighter
Turn electronic key in steering lock to position 1 or 2. Push in lighter (1); it will pop out automatically when hot.
Warning! Never touch the heating element or sides of the lighter, they are extremely hot, hold at knob only. When leaving the vehicle always remove the electronic key from the steering lock. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.
The lighter socket can be used to accommodate electrical accessories up to maximum 85 W.
Interior equipment
159
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 160 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
160
Enlarged cargo area – split folding rear seat backrest
1 Locking handle, left backrest 2 Locking handle, right backrest 3 Pass-through The two sections can be folded down separately to enlarge the cargo area.
4 Indicator, right backrest lock, visible in unlocked
position
5 Indicator, left backrest lock, visible in unlocked
position
J_C208_II.book Seite 161 Donnerstag, 31. Mai 2001 10:13 10
Fold down: Pull locking handle and fold backrest forward.
Set up: Pull backrest up until it locks in its upright position. Check for secure locking by pushing and pulling on the backrest.
Warning! Always lock backrest in its upright position when rear seat bench is occupied by passengers, cargo is being carried in the trunk, or the extended cargo area is not in use.
Note: To prevent unauthorized persons from access to the trunk, always lock backrest in its upright position.
Interior equipment
161
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 162 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Interior equipment
162
Loading instructions
P82.55-2002-26
The total load weight including vehicle occupants and luggage/cargo should not exceed the vehicle capacity weight indicated on the certification label which can be found on the left door pillar.
The handling characteristics of a fully loaded vehicle depend greatly on the load distribution. It is therefore recommended to load the vehicle according to the illustrations shown, with the heaviest items being placed towards the front of the vehicle. Always place items being carried against front or rear seat backrests, and fasten them as securely as possible. The heaviest portion of the cargo should always be kept as low as possible since it influences the handling characteristics of the vehicle.
Notes: The trunk is the preferred place to carry objects. The enlarged cargo area should only be used for items which do not fit in the trunk alone.
J_C208_II.book Seite 163 Donnerstag, 31. Mai 2001 10:13 10
Warning! In an accident, during hard braking or sudden maneuvers, loose items will be thrown around inside the vehicle, and can cause injury to vehicle occupants unless the items are securely fastened in the vehicle. To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things. Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs. Do not place anything on the shelf below the rear window. Never drive vehicle with trunk lid open while pass- through is not closed and seat backrest sections not locked in their upright positions. Deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
Cargo tie down rings
1 Ring Carefully secure cargo by applying even load on all four rings with rope of sufficient strength to hold down the cargo.
Interior equipment
163
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 164 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Telephone
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Parcel net in front passenger footwell A small convenience parcel net is located in the front passenger footwell. It is for small and light items, such as road maps, mail, etc..
Warning! Do not place heavy or fragile objects, or objects having sharp edges, in the parcel net. In an accident, during hard braking or sudden maneuvers, they could be thrown around inside the vehicle, and cause injury to vehicle occupants.
Note: With large objects stored in the parcel net do not slide the seat fully forward, it could damage them.
164
Telephone, general
Warning! A driver’s attention to the road must always be his/ her primary focus when driving. For your safety and the safety of others, we recommend that you pull over to a safe location and stop before placing or taking a telephone call. If you choose to use the telephone while driving, please use the hands-free device and only use the telephone when road and traffic conditions permit. Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle. Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of approximately 50 feet (approximately 14 m) every second. Never operate radio transmitters equipped with a built-in or attached antenna (i.e. without being connected to an external antenna) from inside the vehicle while the engine is running. Doing so could lead to a malfunction of the vehicle’s electronic system, possibly resulting in an accident and personal injury.
J_C208_II.book Seite 165 Donnerstag, 31. Mai 2001 10:13 10
Cellular telephone The vehicle is prepared for the installation of a cellular telephone. For further information and installation contact your authorized Mercedes-Benz Center.
Warning! Some jurisdictions prohibit the driver from using a cellular telephone while driving a vehicle. Whether or not prohibited by law, for safety reasons, the driver should not use the cellular telephone while the vehicle is in motion. Stop the vehicle in an safe location before answering or placing a call.
Telephone
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
165
J_C208_II.book Seite 166 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Garage door opener
166
Garage door opener
1 Signal transmitter keys 2 Indicator lamp 3 Portable remote control transmitter
The built-in remote control is capable of operating up to three separately controlled objects.
Warning! When programming a garage door opener, the door moves up or down. When programming or operating the remote control make sure there is no possibility of anyone being harmed by the moving door.
Notes: Certain types of garage door openers are incompatible with the integrated opener. If you should experience difficulties with programming the transmitter, contact your authorized Mercedes-Benz Center, or call Mercedes-Benz Customer Assistance Center (in the USA only) at 1-800-FOR-MERCedes, or Customer Service (in Canada) at 1-800-387-0100.
J_C208_II.book Seite 167 Donnerstag, 31. Mai 2001 10:13 10
For operation in the USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized modification to this device could void to the user’s authority to operate the equipment.
Programming or reprogramming the integrated remote control:
1. Turn electronic key in steering lock to position 1
or 2.
2. Hold the end of the hand-held transmitter of the
device you wish to train approximately 2 to 5 inches (5 cm to 12 cm) away from the surface of the integrated remote control located on the inside rear view mirror, keeping the indicator lamp in view.
3. Using both hands, simultaneously push the hand- held transmitter button and the desired integrated remote control button. Do not release the buttons until completing step 4.
4. The indicator lamp on the integrated remote control
will flash, first slowly and then rapidly. When the indicator lamp flashes rapidly, both buttons may be released (the rapid flashing lamp indicates successful programming of the new frequency signal). To program the remaining two buttons, follow steps 1 though 4.
Note: If after repeated attempts, you do not successfully program the integrated remote control device to learn the signal of the hand-held transmitter, the garage door opener could be equipped with the “rolling code feature”.
Garage door opener
167
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
J_C208_II.book Seite 168 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Garage door opener
168
Rolling code programming: To train a garage door opener (or other rolling code devices) with the rolling code feature, follow these instructions after completing the “Programming” portion of this text. (A second person may make the following training procedures quicker and easier.)
1. Locate training button on the garage door opener
motor head unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the transmitting button, reference to garage door opener operator’s manual. 2. Press “training” button on the garage door opener
motor head unit (which activated the “training light”). Note: Following step 2, there are 30 seconds to initiate step 3.
3. Firmly press and release the programmed
integrated remote control transmit button. Press and release same button a second time to complete the training process. (Some garage door openers may require you to do this procedure a third time to complete the training.)
4. Confirm the garage door operation by pressing the
programmed button on the integrated remote control transmitter.
Canadian programming: During programming, your hand-held transmitter may automatically stop transmitting. Continue to press and hold the integrated remote control transmitter button (note steps 2 through 4 in the “Programming” portion) while you press and re-press (“cycle”) your hand-held transmitter every two seconds until the frequency signal has been learned. The indicator lamp will flash slowly and then rapidly after several seconds upon successful training.
J_C208_II.book Seite 169 Donnerstag, 31. Mai 2001 10:13 10
Operation of remote control:
Erasing the remote control memory:
1. Turn electronic key in steering lock to position 1
or 2.
1. Turn electronic key in steering lock to position 1
or 2.
2. Select and press the appropriate button to activate the remote controlled device. The integrated remote control transmitter continues to send the signal as long as the button is pressed – up to 20 seconds.
2. Simultaneously holding down the left and right side
buttons for approximately 20 seconds, or until the control lamp blinks rapidly, will erase the codes of all three channels.
Garage door opener
169
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
170
J_C208_II.book Seite 170 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Ski sack (optional on model CLK 430)
P91.10-2056-26
P91.10-2061.26
Unfolding and loading
1. Fold armrest (1) down. 2. Swing cover (2) down. 3. Pull ski sack into passenger compartment and
unfold.
4. Swing flap (3) in trunk up (a magnet will hold flap
in its top position).
5. Slide skis into ski sack.
Warning! The ski sack is designed for up to two pairs of skis. Do not load the ski sack with other objects. Always fasten the ski sack securely. In an accident, an unfastened ski sack can cause injury to vehicle occupants.
J_C208_II.book Seite 171 Donnerstag, 31. Mai 2001 10:13 10
P91.10-2063-26
6. Wrap strap around ski sack and armrest (4). 7. Close clasp (arrow up) and pull strap (5) tight
(arrow down) to immobilize skis.
8. Connect snap hook (6) of front strap to eye (7)
located on center tunnel in front of rear seat bench.
Ski sack
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
171
J_C208_II.book Seite 172 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
172
P91.10-2048-26
P91.10-2058-26
Unloading and folding
1. Loosen strap, open clasp by pressing tabs (arrows)
together, and unload skis.
2. Close flap in trunk. 3. Disconnect snap hook from eye located on center
tunnel in front of rear seat bench.
4. Fold and flatten ski sack lengthwise. 5. Wrap strap with snap hook around ski sack. 6. Fold back the reinforced ski sack tip (8), then
continue to roll up the ski sack tightly.
J_C208_II.book Seite 173 Donnerstag, 31. Mai 2001 10:13 10
7. Place rear strap in fold of ski sack.
8. Place folded ski sack inside recess of backrest.
P91.10-2060-26
P91.10-2057-26
Ski sack
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
173
J_C208_II.book Seite 174 Donnerstag, 31. Mai 2001 10:13 10
Instruments and controls
Ski sack
Operation
Driving
Instrument cluster display
Practical hints
Car care
Technical
data
Index
174
Removal of ski sack For removal of ski sack we recommend that you contact an authorized Mercedes-Benz Center.
Warning! Never drive vehicle with trunk lid open while the ski sack is removed. Deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.
9. Close ski sack compartment cover.
P91.10-2059-26
Note: To prevent unauthorized persons from obtaining access to the trunk, always close the pass-through.
J_C208_II.book Seite 175 Donnerstag, 31. Mai 2001 10:13 10
Driving
Control and operation of
radio transmitters ..................... 176
The first 1 000 miles
(1 500 km) .................................177
Maintenance ...................................177
Catalytic converter ........................ 178
Emission control ............................179
Tele Aid ........................................... 180
Steering lock ................................... 190
Starting and turning offthe engine .................................. 192
Automatic transmission ............... 193
Parking brake .................................202Cruise control ................................. 212
Brake assist system(BAS) ........................................... 214
Antilock brake system
(ABS) ........................................... 216
Electronic stability program
(ESP) ........................................... 218
What you should know
at the gas station .......................222
Check regularly and
before a long trip ......................224
Driving instructions ...................... 203
Drive sensibly – save fuel ........ 203
Drinking and driving ................ 203
Pedals .......................................... 203
Power assistance ........................ 204
Brakes .......................................... 204
Driving off ................................... 205
Parking ........................................ 206
Tires ............................................. 206
Snow chains ............................... 209
Winter driving instructions ................................ 209
Deep water ...................................210
Passenger compartment ............211
Traveling abroad .........................211Contents – Driving
175
Instruments and controls
Operation
Driving
Instrument cluster display
Practical hints
Car care
