2012 Mercedes-benz CL Class Owners Manual

? To store the current speed or to call up

the last stored speed

A To set the specified minimum distance

Switching on DISTRONIC PLUS, storing the current speed and maintaining it Important safety notes G WARNING The vehicle can be braked when DISTRONIC PLUS is activated. For this reason, deactivate DISTRONIC PLUS if the vehicle is to be set in motion by other means (e.g. in a car wash or by towing).

In order to activate DISTRONIC PLUS, the following conditions must be fulfilled: Rthe engine must be started. It may take up

to two minutes after pulling away before DISTRONIC PLUS is operational.

Rthe electric parking brake must be

released.

RESP® must be activated but not

intervening.

Rthe transmission must be in position D. Rthe hood must be closed. Rthe driver's door must be closed when you shift from P to D or your seat belt must be fastened.

Rthe front-passenger door must be closed. Rthe vehicle must not skid. Activating while driving When driving at speeds below 20 mph (30 km/h), you can only activate DISTRONIC PLUS if the vehicle in front has been detected and is shown in the multifunction display. If the vehicle in front is no longer detected and shown, DISTRONIC PLUS is deactivated and a warning tone sounds.

296 Driving systems

X Briefly pull the cruise control lever towards you ?, or briefly press up : or down ;. DISTRONIC PLUS is selected.

X Keep the cruise control lever pressed

up : or down ; until the desired speed is set.

X Remove your foot from the accelerator

pedal. Your vehicle adapts its speed to that of the vehicle in front, but only up to the desired stored speed. i If you do not fully release the accelerator pedal, the DISTRONIC PLUS Override message is shown in the multifunction display. The set distance to a slower- moving vehicle in front will then not be maintained. You will be driving at the speed you determine by the position of the accelerator pedal.

Activating when driving towards a stationary vehicle If the vehicle in front of you is stationary, you can only activate DISTRONIC PLUS once your vehicle is stationary as well. X Briefly pull the cruise control lever towards you ?, or briefly press up : or down ;. DISTRONIC PLUS is selected.

i DISTRONIC PLUS can only be activated at under 20 mph (30 km/h) if a vehicle in front has been detected. Therefore, the DISTRONIC PLUS distance display in the instrument cluster should be activated (Y page 341).

X Keep the cruise control lever pressed

up : or down ; until the desired speed is set.

i You can use the cruise control lever to set

the stored speed and the control on the cruise control lever to set the specified minimum distance (Y page 298).

Pulling away X If the vehicle in front pulls away: remove

your foot from the brake pedal.

X Briefly pull the cruise control lever towards

you ?.

or X Accelerate briefly.

Your vehicle pulls away and adapts its speed to that of the vehicle in front.

Driving If there is no vehicle in front, DISTRONIC PLUS operates in the same way as cruise control. If a slower-moving vehicle is detected in front, DISTRONIC causes your vehicle to brake. This maintains the preset distance to the vehicle in front. If DISTRONIC PLUS detects a faster-moving vehicle in front, it increases the driving speed of your vehicle, but only up to the desired speed you have stored. G WARNING If you depress the brake, DISTRONIC PLUS is deactivated unless your vehicle is stationary. DISTRONIC PLUS then no longer brakes your vehicle. In such cases, control the distance from vehicles travelling in front with the brake alone. You could otherwise cause an accident and thereby injure yourself and others. The driver remains fully responsible for the vehicle's distance from other vehicles, the speed being driven and for braking in good time.

Changing lanes If you wish to change to the passing lane (in left-hand-drive vehicles, the passing lane is the left-hand lane), DISTRONIC PLUS supports you if: Ryou are driving faster than 40 mph

(60 km/h).

RDISTRONIC PLUS is maintaining the

distance to a vehicle in front.

Driving systems

297

Ryou switch on the appropriate turn signals. RDISTRONIC PLUS does not detect a danger

of collision.

If these conditions are met, your vehicle is accelerated. Acceleration will be interrupted if changing lanes takes too long or if the distance between your vehicle and the vehicle in front becomes too small. G WARNING DISTRONIC PLUS and Active Blind Spot Assist are only aids designed to assist driving. They do not relieve you of the responsibility of paying attention. The driver remains fully responsible for the vehicle's distance from other vehicles, the vehicle's speed and for braking in good time. Always pay attention to traffic conditions and your surroundings. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.

Stopping G WARNING Never get out of the vehicle when DISTRONIC PLUS is activated. DISTRONIC PLUS must also never be operated, activated or deactivated by a passenger or from outside the vehicle. DISTRONIC PLUS does not replace the electric parking brake and must not be used for parking. The DISTRONIC PLUS braking effect is canceled and the vehicle can start moving if: RDISTRONIC PLUS is deactivated using the

cruise control lever.

Ryou accelerate. Rthere is a malfunction in the system or an

interruption in the power supply, e.g. battery failure.

Rthe electrical system in the engine

compartment, the battery or the fuses are tampered with.

Rthe battery is disconnected.

If you wish to leave the vehicle or park it, deactivate DISTRONIC PLUS and secure the vehicle against rolling away.

If DISTRONIC PLUS detects that the vehicle in front is stopping, it brakes your vehicle until it is stationary. Once your vehicle is stationary, it remains stationary and you do not need to depress the brake. i After a time, the electric parking brake

secures the vehicle and relieves the service brake.

i Depending on the specified minimum

distance, your vehicle will come to a standstill at a sufficient distance behind the vehicle in front. The specified minimum distance is set using the control on the cruise control lever.

Setting a speed G WARNING Keep in mind that it may take a brief moment until the vehicle has made the necessary adjustments. Increase or decrease the set vehicle speed to a value that the prevailing road conditions and legal speed limits permit. Otherwise, sudden and unexpected acceleration or deceleration of the vehicle could cause an accident and/ or serious injury to you and others.

X Press the cruise control lever up : for a higher speed or down ; for a lower speed. X Keep the cruise control lever pressed until

the desired speed is reached.

X Release the cruise control lever.

The new speed is stored. DISTRONIC PLUS is activated and adjusts the vehicle's speed to the new speed stored.

see this distance in the multifunction display (Y page 299). G WARNING It is up to the driver to exercise discretion to select the appropriate setting given road conditions, traffic, driver's preferred driving style and applicable laws and driving recommendations for safe following distance.

X To increase: turn control ; in direction

=. DISTRONIC PLUS then maintains a greater distance between your vehicle and the vehicle in front.

X To decrease: turn control ; in

direction :. DISTRONIC PLUS then maintains a shorter distance between your vehicle and the vehicle in front.

i Make sure that you maintain a sufficient and safe distance from the vehicle in front. Adjust the distance to the vehicle in front if necessary.

298 Driving systems

Making adjustments in 1 mph (Canada: 1 km/h) increments X Briefly press the cruise control lever to the pressure point, up : for a higher speed or down ; for a lower speed. The last speed stored is increased or reduced.

Making adjustments in 5 mph (Canada: 10 km/h) increments X Briefly press the cruise control lever

beyond the pressure point, up : for a higher speed or down ; for a lower speed. The last speed stored is increased or reduced.

Storing the current speed or calling up a stored speed G WARNING The set speed stored in memory should only be set again if prevailing road conditions and legal speed limits permit. Possible acceleration or deceleration differences arising from returning to the preset speed could cause an accident and/or serious injury to you and others.

X Briefly pull the cruise control lever towards

you ?.

X Remove your foot from the accelerator

pedal. DISTRONIC PLUS is activated. The first time it is activated, the current speed is stored. Otherwise, it sets the vehicle cruise speed to the previously stored value.

Setting the specified minimum distance You can set the specified minimum distance for DISTRONIC PLUS by varying the time span between one and two seconds. With this function, you can set the minimum distance that DISTRONIC PLUS keeps to the vehicle in front, dependent on vehicle speed. You can

DISTRONIC PLUS displays in the speedometer

Driving systems

299

When you switch on DISTRONIC PLUS, triangle ; shows the stored speed. i For design reasons, the speed displayed in the speedometer may differ slightly from the speed set for DISTRONIC PLUS.

If DISTRONIC PLUS detects a vehicle in front, the speedometer dial lights up between speed of the vehicle in front : and stored speed ;.

DISTRONIC PLUS displays in the multifunction display General notes You can select the distance display in the Assistance menu (Y page 341) of the on- board computer. Display when DISTRONIC PLUS is deactivated X Select the Distance Display function using the on-board computer (Y page 341).

When DISTRONIC PLUS is deactivated, you will see the following in the multifunction display:

: Symbol for activated PRE-SAFE® Brake ; Vehicle in front, if detected = Distance indicator, current distance to

the vehicle in front

? Specified minimum distance to the

vehicle in front; adjustable

A Own vehicle Display when DISTRONIC PLUS is activated X Select the Distance Display function using the on-board computer (Y page 341).

You will see the stored speed for about five seconds when you activate DISTRONIC PLUS. After this time, you will see the following in the multifunction display while DISTRONIC PLUS is activated:

: DISTRONIC PLUS activated ; Own vehicle = Specified minimum distance to the

vehicle in front; adjustable ? Vehicle in front, if detected

300 Driving systems

Deactivating DISTRONIC PLUS

There are several ways to deactivate DISTRONIC PLUS: X Briefly press the cruise control lever

forwards :.

or X Brake, unless the vehicle is stationary. When you deactivate DISTRONIC PLUS, the DISTRONIC PLUS Off message is shown in the multifunction display for approximately five seconds. i The last speed stored remains stored until

you switch off the engine.

i DISTRONIC PLUS is not deactivated if you

depress the accelerator pedal. If you accelerate to overtake, DISTRONIC PLUS adjusts the vehicle's speed to the last speed stored after you have finished overtaking.

DISTRONIC PLUS is automatically deactivated if: Ryou engage the electric parking brake or if

the vehicle is automatically secured with the electric parking brake. Ryou are driving slower than

15 mph (25 km/h) and there is no vehicle in front, or if the vehicle in front is no longer detected.

RESP® intervenes or you deactivate ESP®. Rthe transmission is in the P, R or N position. Ryou switch off the radar sensor system

(Y page 344).

Ryou pull the cruise control lever towards you in order to pull away and the front- passenger door is open. Rthe vehicle has skidded. If DISTRONIC PLUS is deactivated, you will hear a warning tone. The DISTRONIC PLUS Off message is shown in the multifunction display for approximately five seconds. G WARNING The DISTRONIC PLUS switches off and releases the brakes when the vehicle decelerates below the minimum speed of 20 mph (30 km/h) by operation of the system unless the DISTRONIC PLUS detects a vehicle directly ahead of you. At that time the driver must apply the brakes in order to reduce vehicle speed further or bring it to a stop.

Tips for driving with DISTRONIC PLUS Important safety notes The following contains descriptions of certain road and traffic conditions in which you must be particularly attentive. In such situations, brake if necessary. DISTRONIC PLUS is then deactivated. G WARNING The DISTRONIC PLUS works to maintain the speed selected by the driver unless a moving obstacle proceeding directly ahead of it in the same travel direction is detected (e.g. following another vehicle ahead of you at your set distance). This means that: RYour vehicle can pass another vehicle after

you have changed lanes.

RWhile in a sharp turn or if the preceding vehicle is in a sharp turn, the DISTRONIC PLUS could lose sight of the preceding vehicle. Your vehicle could then accelerate to the previously selected speed.

The DISTRONIC PLUS regulates only the distance between your vehicle and those directly ahead of it. It may not register stationary objects in the road, e.g.: Ra stopped vehicle in a traffic jam Ra disabled vehicle Ran oncoming vehicle The driver must always be alert, observe all traffic and intercede as required by means of steering or braking the vehicle. G WARNING The DISTRONIC PLUS should not be used in snowy or icy road conditions.

Cornering, going into and coming out of a bend

Driving systems

301

DISTRONIC PLUS may not detect vehicles traveling on a different line. The distance to the vehicle in front will be too short. Other vehicles changing lane

DISTRONIC PLUS has not detected the vehicle cutting in yet. The distance to this vehicle will be too short. Narrow vehicles

The ability of DISTRONIC PLUS to detect vehicles when cornering is limited. Your vehicle may brake unexpectedly or late. Vehicles traveling on a different line

DISTRONIC PLUS has not yet detected the vehicle in front on the edge of the road, because of its narrow width. The distance to the vehicle in front will be too short.

302 Driving systems

Obstructions and stationary vehicles

DISTRONIC PLUS does not brake for obstacles or stationary vehicles. If, for example, the detected vehicle turns a corner and reveals an obstacle or stationary vehicle, DISTRONIC PLUS will not brake for these. Crossing vehicles

The vehicle is kept stationary without the driver having to depress the brake pedal. The braking effect is canceled and the HOLD function deactivated when you depress the accelerator pedal to pull away.

Activation conditions You can activate the HOLD function if: Rthe vehicle is stationary. Rthe driver's door is closed or your seat belt

is fastened.

Rthe electric parking brake is released. Rthe hood is closed. Rthe transmission is in position R, N or D. The trunk lid must be closed in position R.

RDISTRONIC PLUS is deactivated.

Activating the HOLD function X Make sure that the activation conditions

are met.

X Depress the brake pedal.

DISTRONIC PLUS may mistakenly detect vehicles that are crossing your lane. Activating DISTRONIC PLUS at traffic lights with crossing traffic, for example, could cause your vehicle to pull away unintentionally.

HOLD function General notes The HOLD function can assist the driver in the following situations: Rwhen pulling away, especially on steep

slopes

Rwhen maneuvering on steep slopes Rwhen waiting in traffic

X Quickly depress the brake pedal further until HOLD display : appears in the instrument cluster. The HOLD function is activated. You can release the brake pedal.

i If depressing the brake pedal the first

time does not activate the HOLD function, wait briefly and then try again. G WARNING The vehicle's brakes are applied when the HOLD function is activated. For this reason, deactivate the HOLD function if the vehicle is to be set in motion by other means (e.g. in a car wash or by towing).

Deactivating the HOLD function The HOLD function is deactivated automatically if: Ryou accelerate and the transmission is in

position D or R.

Ryou shift the transmission to position P. Ryou apply the brakes again with a certain amount of pressure until HOLD disappears from the instrument cluster.

Ryou secure the vehicle using the electric

parking brake.

Ryou activate DISTRONIC PLUS. i After a time, the electric parking brake

secures the vehicle and relieves the service brake. G WARNING Never get out of the vehicle when the HOLD function is activated. The HOLD function must never be operated or deactivated by a passenger or from outside the vehicle. The HOLD function does not replace the electric parking brake and must not be used for parking. The braking effect of the HOLD function is canceled and the vehicle could roll away if: Rthe HOLD function is deactivated by

depressing the accelerator pedal or the brake pedal.

Rthere is a malfunction in the system or an

interruption in the power supply, e.g. battery failure.

Rthe electrical system in the engine

compartment, the battery or the fuses are tampered with.

Rthe battery is disconnected.

Driving systems

303

AIRMATIC Vehicle level Important safety notes Your vehicle regulates its height automatically. All-round self-leveling ensures the best possible suspension and constant ground clearance, even with a laden vehicle. When you drive fast, the vehicle is lowered automatically to improve driving safety and to reduce fuel consumption. The following vehicle levels are possible: Rnormal Rraised: the vehicle is raised by about 1.20 in (30 mm) when compared with the normal level

Rlowered: the vehicle is lowered by about 0.40 in (10 mm) when compared with the normal level

The "Normal" and "Raised" vehicle levels can be set manually. The "Lowered” vehicle level is set automatically at speeds over 60 mph (100 km/h). Setting the vehicle level Select the "Normal" setting for normal road surfaces and "Raised" for driving with snow chains or on particularly poor road surfaces. Your selection remains stored even if you remove the SmartKey from the ignition lock. G WARNING To help avoid personal injury, keep hands and feet away from wheel housing area, and stay away from under the vehicle when lowering the vehicle chassis.

304 Driving systems

The damping is tuned individually to each wheel and depends on: Ryour driving style, e.g. sporty Rthe road surface condition, e.g. bumps Ryour individual selection, i.e. sports or

comfort

Your selection remains stored even if you remove the SmartKey from the ignition lock.

Sports tuning The firmer suspension tuning in Sport mode ensures even better contact with the road. Select this mode when employing a sporty driving style, e.g. on winding country roads. X If indicator lamp ; is not lit: press

button :. Indicator lamp ; lights up. Sports suspension tuning is selected. The AIRMATIC SPORT message appears in the multifunction display.

Comfort tuning In Comfort mode, the driving characteristics of your vehicle are more comfortable. Select this mode if you prefer a more comfortable driving style, but also when driving fast on straight roads, e.g. highways. X If indicator lamp ; is lit: press

button :. Indicator lamp ; goes out. Comfort tuning is selected. The AIRMATIC COMFORT message appears in the multifunction display.

Setting raised level X Start the engine. If indicator lamp ; is not lit: X Press button :.

Indicator lamp ; lights up. The vehicle height is adjusted to raised level. The Vehicle rising message appears in the multifunction display.

The "Raised level" setting is canceled if you: Rdrive at speeds above approximately

75 mph (120 km/h)

Rdrive about 3 minutes at speeds above

50 mph (80 km/h)

The "Raised level" remains active when you are not driving within these speed ranges. Setting the normal level X Start the engine. If indicator lamp ; is lit: X Press button :.

Indicator lamp ; goes out. The vehicle is adjusted to normal level.

Suspension tuning General notes The Adaptive Damping System (ADS) automatically controls the calibration of the dampers and springs.

Driving systems

305

Active Body Control (ABC) Vehicle level Your vehicle automatically adjusts its ride height to improve driving safety and reduce fuel consumption. Depending on the vehicle height that has been set, the vehicle automatically adjusts its height dependent on the current speed. As speed increases, the vehicle is lowered by up to 0.4 in (10 mm). As the speed is reduced, the vehicle is raised up to the set vehicle height. G WARNING The vehicle is lowered when the engine is switched off. Therefore, make sure that nobody is in the vicinity of the wheel housing or under the vehicle when you switch off the engine. Otherwise, limbs could become trapped.

! The vehicle is lowered when the engine is switched off. Make sure when parking that you position your vehicle so that it does not make contact with the curb as the vehicle is lowered. Your vehicle could otherwise be damaged.

i For AMG vehicles: when the engine is switched off, the vehicle is lowered by approx. 0.2 in (5 mm). Setting the vehicle level Select the "Normal" setting for normal road surfaces and "Raised" for driving with snow chains or on particularly poor road surfaces. G WARNING To help avoid personal injury, keep hands and feet away from wheel housing area, and stay away from under the vehicle when lowering the vehicle chassis.

Your selection remains stored even if you remove the SmartKey from the ignition lock.

Setting raised level X Start the engine. If indicator lamp ; is not lit: X Press button :.

Indicator lamp ; lights up. The vehicle height is adjusted to raised level.

Setting the normal level X Start the engine. If indicator lamp ; is lit: X Press button :.

Indicator lamp ; goes out. The vehicle is adjusted to normal level.

Suspension tuning The electronically controlled ABC suspension system works continuously. This improves driving safety and comfort. The ABC suspension system is tuned individually to each wheel and depends on: Ryour driving style, e.g. sporty Rthe road surface condition, e.g. bumps Ryour individual selection, i.e. sports or

comfort

Rthe vehicle load Your selection remains stored even if you remove the SmartKey from the ignition lock.

306 Driving systems

whenever a drive wheel spins due to insufficient grip. G WARNING If a drive wheel is spinning due to insufficient traction: RWhile driving off, apply as little throttle as

possible.

RWhile driving, ease up on the accelerator

pedal.

RAdapt your speed and driving style to the

prevailing road conditions.

Failure to observe these guidelines could cause the vehicle to skid. The 4MATIC cannot prevent accidents resulting from excessive speed.

! Never tow the vehicle with one axle

raised. This may damage the transfer case. Damage of this sort is not covered by the Mercedes-Benz Limited Warranty. All wheels must remain either on the ground or be fully raised. Observe the instructions for towing the vehicle with all wheels in full contact with the ground.

i In wintry driving conditions, the maximum

effect of 4MATIC can only be achieved if you use winter tires (M+S tires), with snow chains if necessary.

PARKTRONIC Important safety notes G WARNING The PARKTRONIC is a supplemental system. It is not intended to, nor does it replace, the need for extreme care. The responsibility during parking and other critical maneuvers always remains with the driver. G WARNING Make sure no persons or animals are in or near the area in which you are parking/ maneuvering. Otherwise, they could be injured.

Sports tuning The firmer suspension tuning in Sport mode ensures even better contact with the road. Select this mode if you prefer a firmer suspension tuning. X If indicator lamp ; is not lit: press

button :. Indicator lamp ; lights up. You have selected the suspension for a sporty driving style. The ABC Active Body Control SPORT message appears in the multifunction display.

Comfort tuning In Comfort mode, the driving characteristics of your vehicle are more comfortable. Select this mode if you prefer a more comfortable driving style. X If indicator lamp ; is lit: press

button :. Indicator lamp ; goes out. You have selected the suspension for a comfortable driving style. The ABC Active Body Control COMFORT message appears in the multifunction display.

4MATIC (permanent four-wheel drive) 4MATIC ensures that all four wheels are permanently driven. Together with ESP®, it improves the traction of your vehicle

Driving systems

307

PARKTRONIC is an electronic parking aid with ultrasonic sensors. It indicates visually and audibly the distance between your vehicle and an object. PARKTRONIC is activated automatically when you: Rswitch on the ignition Rshift the transmission to position D, R or N Rrelease the electric parking brake PARKTRONIC is deactivated at speeds above 11 mph (18 km/h). It is reactivated at lower speeds. PARKTRONIC monitors the area around your vehicle using six sensors in the front bumper and four sensors in the rear bumper.

Side view

: Sensors in the front bumper, left-hand

side (example)

Range of the sensors General notes The sensors must be free of dirt, ice and slush; otherwise they may not function correctly. Clean the sensors regularly, taking care not to scratch or damage them (Y page 418).

Top view Front sensors Center

Corners

Rear sensors Center

Corners

Approximately 40 in (approximately 100 cm) Approximately 24 in (approximately 60 cm)

Approximately 48 in (approximately 120 cm) Approximately 32 in (approximately 80 cm)

! When parking, pay particular attention to objects above or below the sensors, such as flower pots or trailer drawbars. PARKTRONIC does not detect such objects when they are in the immediate vicinity of the vehicle. You could damage the vehicle or the objects. The sensors may not detect snow and other objects that absorb ultrasonic waves.

308 Driving systems

Ultrasonic sources such as an automatic car wash, the compressed-air brakes on a truck or a pneumatic drill could cause PARKTRONIC to malfunction. PARKTRONIC may not function correctly on uneven terrain.

Minimum distance Center

Corners

Approximately 8 in (approximately 20 cm) Approximately 8 in (approximately 20 cm)

If there is an obstacle within this range, the relevant warning displays light up and a warning tone sounds. If the distance falls below the minimum, the distance may no longer be shown.

Warning displays The warning displays show the distance between the sensors and the obstacle. The warning display for the front area is in the instrument cluster. The warning display for the rear area is located on the headliner in the rear compartment.

yellow segments showing operational readiness = light up. The selected transmission position determines which warning display is active when the engine is running. Transmission position

Warning display

Front area activated Rear and front areas activated If the electric parking brake is engaged: no areas are activated If the electric parking brake is released: rear and front areas are activated No areas activated

One or more segments light up as the vehicle approaches an obstacle, depending on the vehicle's distance from the obstacle. When the first red segment lights up, you hear an intermittent warning for about two seconds. From the second red segment, you hear a continuous warning. This indicates that you have now reached the minimum distance.

Deactivating/activating PARKTRONIC

Warning display for the front area : Segments on the left-hand side of the

vehicle

; Segments on the right-hand side of the

vehicle

= Segments showing operational readiness The warning display for each side of the vehicle is divided into five yellow and two red segments. PARKTRONIC is operational if

: To deactivate/activate PARKTRONIC ; Indicator lamp

Driving systems

309

If indicator lamp ; lights up, PARKTRONIC is deactivated. i PARKTRONIC is automatically activated when you turn the SmartKey to position 2
in the ignition lock.

310 Driving systems

Problems with PARKTRONIC

Problem Only the red segments in the PARKTRONIC warning displays are lit. You also hear a warning tone for approximately two seconds. PARKTRONIC is deactivated after approximately 20 seconds, and the indicator lamp in the PARKTRONIC button lights up.

Only the red segments in the PARKTRONIC warning displays are lit. PARKTRONIC is deactivated after approximately 20
seconds.

Possible causes/consequences and M Solutions PARKTRONIC has malfunctioned and has switched off. X If problems persist, have PARKTRONIC checked at a qualified

specialist workshop.

The PARKTRONIC sensors are dirty or there is interference. X Clean the PARKTRONIC sensors (Y page 418). X Switch the ignition back on. The problem may be caused by an external source of radio or ultrasound waves. X See if PARKTRONIC functions in a different location.

Parking Guidance Important safety notes Parking Guidance is an electronic parking aid with ultrasound. Ultrasound is used to measure the road on both sides of the vehicle. A suitable parking space is indicated by the parking symbol. You receive steering instructions when parking. You may also use PARKTRONIC (Y page 306). G WARNING Parking Guidance is merely an aid and may display parking spaces that are not suitable for parking, for example: Rno-parking areas Rparking spaces with unsuitable surfaces

(road surface)

Rdriveways Rentrances and exits Parking Guidance detects and measures potential parking spaces while driving past. Changes to the parking space after this point are not taken into account, for example if the vehicle in front of or behind the parking space changes position or objects in the parking space are moved. Even when using Parking Guidance, you are still responsible for driving carefully. If you rely on Parking Guidance alone, you could cause an accident and injure yourself and others. Safety always remains your responsibility and you must continue paying careful attention to your immediate surroundings when parking and maneuvering.

Driving systems

311

G WARNING Objects located above the height range of Parking Guidance will not be detected when the parking space is measured. These objects are not taken into account when the parking procedure is calculated, e.g. overhanging loads, tail sections or loading ramps of goods vehicles. Under some circumstances, Parking Guidance might therefore issue steering instructions too soon. This may lead to a collision. For this reason, you should avoid using Parking Guidance in such situations. G WARNING Make sure that no persons or animals are in the maneuvering range. Otherwise, they could be injured.

! Pay particular attention to low objects or

objects with flat surfaces, such as trailer drawbars, posts, cross beams and curbs. These types of objects cannot be detected by Parking Guidance and may damage the vehicle.

When PARKTRONIC is deactivated, Parking Guidance is also unavailable. Use Parking Guidance for parking spaces: Rthat are parallel to the direction of travel Rthat are on straight roads, not bends Rthat are on the same level as the road, i.e. not on the pavement, for example. Parking Guidance may not detect flat curbs

Parking tips: Ron narrow roads, drive past the parking

space as close as possible.

Rparking spaces that are littered, overgrown

or partially occupied by trailer drawbars might be identified incorrectly or not at all. Rsnowfall or heavy rain may lead to a parking

space being measured inaccurately.

Rpay attention to the PARKTRONIC

(Y page 308) warning messages during the parking procedure.

Rwhen transporting a load which protrudes from your vehicle, you must not use Parking Guidance.

Rnever use Parking Guidance with snow

chains or an emergency spare wheel installed.

Rmake sure that the tire pressures are

always correct. This has a direct effect on the steering instructions.

Rthe way your vehicle is positioned in the parking space after parking is dependent on various factors. These include the position and shape of the vehicles parked in front and behind it and the conditions of the location. In some cases, Parking Guidance may guide you too far or not far enough into a parking space. In some cases, it may also lead you across or onto the curb. If necessary, cancel the parking procedure with Parking Guidance.

! If unavoidable, you should drive over

obstacles such as curbs slowly and not at a sharp angle. Otherwise, you may damage the wheels or tires.

Detecting a parking space

: Detected parking space on the left ; Parking symbol = Detected parking space on the right Parking Guidance is automatically activated when you drive forwards. The system is operational at speeds of up to approximately 22 mph (35 km/h). While in operation, the system independently locates and measures parking spaces on both sides of the vehicle. At speeds below 19 mph (30 km/h), you see white parking symbol ; in the instrument cluster as a status indicator. Parking

312 Driving systems

Guidance only shows parking spaces on the passenger side in the default setting. Parking spaces on the driver's side are displayed as soon as the turn signal on the driver's side is activated. To park on the driver's side, you must leave the driver's side turn signal switched on until you have engaged reverse gear. If a parking space is detected, parking symbol ; changes to blue. Additionally, an arrow pointing right = or left : is shown. Parking Guidance will only detect parking spaces: Rthat are closed in at the back Rthat are parallel to the direction of travel Rthat are at least 5 ft (1.5 m) wide Rthat are at least 4.3 ft (1.3 m) longer than

your vehicle

A parking space is displayed while you are driving past it, and until you are approximately 50 ft (15 m) away from it.

Parking The following instructions refer to parking in a space on the front-passenger side. To park in a space on the driver's side, mirror the instructions. G WARNING The Parking Guidance is only an aid and may not detect all obstacles. The Parking Guidance does not relieve you of the responsibility to pay attention. You are always responsible for safety and must continue to pay attention to your immediate surroundings when parking and maneuvering. Otherwise, you could endanger yourself and others.

X Stop the vehicle when the blue parking space symbol shows the desired parking space in the instrument cluster.

X Engage reverse gear. The multifunction display shows the message: Check surroundings Confirm with OK. X Press a on the multifunction steering

wheel to confirm. The display in the instrument cluster switches to Parking Guidance.

: Green lane ; White bracket marking the target position X Depending on the distance, you may have

to reverse along the lane towards the parking space. This is indicated by green lane :. Continue backing up until you hear a tone. Stop; the parking position has been reached and is marked by white bracket ; with an arrow for the target position.

Driving systems

313

Countersteering

Steering tips : Red lane indicating the route the vehicle

will take with the steering wheel in its current position

; Yellow lane indicating the route the

vehicle will take when you have turned the steering wheel in the required direction X Turn the steering wheel while the vehicle is

stationary until red lane : and yellow lane ; overlap. Lane ; is then marked in green and you hear a tone. If the parking space is inside the area displayed, the end of the green lane is marked with a white bracket and an arrow showing the target position.

Backing up into a parking space

: Red lane indicating the route the vehicle

will take with the steering wheel in its current position

; Yellow lane indicating the route the

vehicle will take when you have turned the steering wheel in the required direction X Turn the steering wheel while the vehicle is

stationary until red lane : and yellow lane ; overlap. Lane ; is then marked in green and you hear a tone. A white arrow and white bracket are shown to indicate the target position.

Driving to the final position

: Lane turns green when the steering wheel

is turned in the correct direction

X Keep the steering wheel in that position

and reverse carefully.

X Stop as soon as you hear a tone.

The vehicle has reached the position in which you need to countersteer.

: Lane turns green when the steering wheel

is turned in the correct direction

X Keep the steering wheel turned in that direction and reverse carefully until you have reached the final position. The Parking Guidance finished message appears in the multifunction display and a tone sounds.

314 Driving systems

The rear view camera is located in the handle strip of the trunk lid.

Final position Depending on the size of the parking space, you may now be in an angled position in the parking space. If possible, Parking Guidance will guide you as far back as possible towards the rear limit of the parking space. X Maneuver to the final position if necessary. X Always observe the warning messages

displayed by PARKTRONIC (Y page 308).

Canceling Parking Guidance X Press the PARKTRONIC button on the

dashboard (Y page 308). Parking Guidance is canceled immediately and PARKTRONIC is deactivated.

Parking Guidance is canceled automatically if it is no longer possible to guide you into the parking space, or if a malfunction occurs. The parking space symbol goes out and a warning tone sounds. The Parking Guidance Canceled message appears in the multifunction display.

Rear view camera Important safety notes The rear view camera is an optical parking aid. It shows the area behind your vehicle in the COMAND display. G WARNING Make sure that no persons or animals are in the maneuvering range. Otherwise, they could be injured.

: Rear view camera

View through the camera The area behind the vehicle is displayed in a mirror-inverted manner, as in the rear-view mirror. G WARNING The rear view camera is only an aid and may display obstacles Rfrom a distorted perspective Rinaccurately Rmay not display obstacles at all The rear view camera does not relieve you of the responsibility to be cautious. Take care and pay careful attention. The rear view camera may not show objects which are Rvery close to the rear bumper Runder the rear bumper Rabove the trunk handle You are responsible for safety at all times and must continue to pay attention to the immediate surroundings when parking and maneuvering. This includes the area behind, in front of, and beside the vehicle. Otherwise you could endanger yourself and/or others. G WARNING The rear view camera will not function or will not fully function if:

Rthe trunk lid is open Rit is raining or snowing strongly or if it is

foggy

Rit is night or if you are parking/

maneuvering your vehicle in a very dark area

Ra very bright white light is affecting the

camera

Rthe immediate vicinity is illuminated with

fluorescent light (the display of the COMAND system can flicker)

Rtemperature changes abruptly, for example

if you drive out of the cold into a heated garage (condensation on the lens) Rthe camera lens is dirty or covered Rthe rear of your vehicle is damaged

In this case, have the position and the setting of the camera checked at a specialist workshop. Mercedes-Benz recommends that you consult a Mercedes- Benz Center for this purpose.

Do not use the rear view camera in these situations. You could otherwise injure yourself and other people and/or cause damage - including damage to your vehicle - while parking/maneuvering.

Activating the rear view camera X Make sure that the SmartKey is in position

2 in the ignition lock. X Engage reverse gear.

The area behind the vehicle is shown in the COMAND display with guide lines.

Guide lines in the COMAND display G WARNING Use of rear view camera can be dangerous if you are color-blind or have impaired color vision. Only use rear view camera if you can see and distinguish all colored guidelines shown by rear view camera on the COMAND system display.

Driving systems

315

G WARNING Please note that objects that do not touch the ground may appear to be further away than they actually are, for example: Rthe bumper of a vehicle parked behind you Rthe trailer drawbar Rthe ball coupling of a trailer tow hitch Rthe rear end of a truck Ra slanted post In such cases, you should not use the guide lines to judge the distance. You may misjudge the distance, which increases the risk of impacting the objects. Even if the object you approach is directly on the ground, do not approach the object any closer than the red guide line.

Information in the COMAND display (example) Guide lines ; and = show the approximate distance to the rear area. Yellow guide line ; indicates a distance of approximately 3 ft (1 m) and red guide line = indicates a distance of approximately 10 in (0.25 m). The distances only apply to objects that are at ground level. Blue guide lines : depict the width required for the vehicle. They are used to align the vehicle with the edge of the road, e.g. the curb.

316 Driving systems

ATTENTION ASSIST Important safety notes ATTENTION ASSIST helps you during long, monotonous journeys such as on freeways and interstate highways. It is active in the range between 50 mph (80 km/h) and 112 mph (180 km/h). If ATTENTION ASSIST detects typical indicators of fatigue or increasing lapses in concentration on the part of the driver, it suggests you take a break. G WARNING ATTENTION ASSIST is only an aid and may detect your tiredness or lapses in concentration too late or not at all. It is not a substitute for a well-rested and attentive driver. Fatigue may cause you to recognize hazardous situations too late, misjudge a situation or react more slowly. For this reason, make sure you feel rested before you begin driving and during your journey. Make sure that you take regular breaks in time, particularly on long journeys. Otherwise, you may fail to recognize dangers in time, cause an accident and injure yourself and others.

ATTENTION ASSIST assesses your level of fatigue or lapses in concentration by taking the following criteria into account: Ryour personal driving style, e.g. steering

characteristics

Rdriving conditions, e.g. time, driving time The functionality of ATTENTION ASSIST is restricted and warnings may be delayed or not occur at all: Rif the road condition is poor, e.g. if the

surface is uneven or if there are potholes

Rif there is a strong side wind Rif you have adopted a sporty driving style with high cornering speeds or high rates of acceleration

Rif you predominantly drive at speeds under

50 mph (80 km/h) or over 112 mph (180 km/h)

Rif you are currently using COMAND or

making a telephone call with it

Rif the time has been set incorrectly Rin active driving situations, such as when you change lanes or change your speed

Warning and display messages in the multifunction display

X Activate ATTENTION ASSIST using the on-

board computer (Y page 342). Symbol : appears in the multifunction display.

If ATTENTION ASSIST is active, you will be warned no sooner than 20 minutes after your journey has begun. You will then hear an intermittent warning tone twice, and the Attention Assist: Time for a break? message appears in the multifunction display. X If necessary, take a break. X Press a to confirm the message. On long journeys, take regular breaks in good time to allow yourself to rest properly. If you do not take a break and ATTENTION ASSIST still detects typical indicators of fatigue or increasing lapses in concentration, you will be warned again after 15 minutes at the earliest. ATTENTION ASSIST is reset when you continue your journey and starts assessing your tiredness again if: Ryou switch off the engine. Ryou take off your seat belt and open the

driver's door, e.g. for a change of drivers or to take a break.

Night View Assist Plus with spotlight function Important safety notes In addition to the illumination provided by the normal headlamps, Night View Assist Plus uses infrared light to illuminate the road. The Night View Assist Plus camera picks up the infrared light and shows a black-and-white image in the multifunction display. The image shown in the multifunction display corresponds to a road lit up by high-beam headlamps. This enables you to see the road's course and any obstacles in good time. If pedestrian recognition is activated, pedestrians recognized by the system are highlighted in the Night View Assist Plus display. The spotlight function also illuminates individual detected pedestrians with a spotlight that flashes four times in quick succession. After this targeted illumination, the headlamps return to the original driving position again. G WARNING Night View Assist Plus is only an aid designed to assist driving. It is not a substitute for attentive driving. Do not rely solely on the Night View Assist Plus display. Continue to look through the windshield. You are responsible for safety and must drive in accordance with traffic conditions. You could otherwise put yourself and others in danger. The system may be impaired or unavailable if: Rthere is poor visibility, e.g. due to snow,

rain, fog or heavy spray.

Rthe windshield is dirty, fogged up or

covered, for instance by a sticker, in the vicinity of the camera.

Ryou are driving on bends, uphill gradients

or downhill gradients.

Light from the headlamps of oncoming vehicles does not affect the Night View Assist Plus display in the multifunction display. This is also the case if you cannot switch on the

Driving systems

317

high-beam headlamps due to oncoming traffic. G WARNING The Night View Assist Plus cannot record objects immediately in front of or next to the vehicle. When maneuvering, continue to look through the windshield. Make sure no persons or animals are in the area in which you are maneuvering. You could otherwise injure them.

i Infrared light is not visible to the human

eye and therefore does not glare. Night View Assist Plus can therefore remain switched on even if there is oncoming traffic.

: Night View Assist Plus camera

Pedestrian recognition G WARNING Pedestrian recognition may be impaired or inoperative if: Rpedestrians are partially or entirely

obscured by objects, e.g. parked vehicles. Rthe silhouette of the pedestrian in the Night

View Assist Plus display is incomplete or interrupted, e.g. by powerful light reflections.

Rpedestrians do not contrast with the

surroundings.

Rpedestrians are not standing upright, for example, if they are sitting, crouching or lying down.

318 Driving systems

i Animals are not recognized by pedestrian

recognition.

Night View Assist Plus is able to recognize pedestrians by typical characteristics, e.g. a silhouette in the shape of a person. Pedestrian recognition is then switched on automatically if: RNight View Assist Plus is activated. Ryou are driving faster than 6 mph

(10 km/h).

Rthe surroundings are dark, e.g. when driving outside built-up areas without street lighting.

If pedestrian recognition is enabled, the active pedestrian recognition symbol (Y page 319) appears in the multifunction display. If a pedestrian is now recognized, they are framed and thereby highlighted. If the pedestrian recognition system has brought a pedestrian to your attention, look through the windshield to evaluate the situation. The actual distance to objects and pedestrians cannot be gauged accurately by looking at a screen. It may be the case that objects are highlighted as well as pedestrians. Spotlight function Pedestrian recognition with spotlight function is activated automatically if: RNight View Assist Plus with spotlight

function is activated.

Ryou are driving faster than 28 mph

(45 km/h).

Rthe surroundings are dark, e.g. when driving outside built-up areas without street lighting.

Only one pedestrian or one object can be illuminated with the spotlight at any one time. The spotlight function will not function if: Rpedestrians or objects cannot be recognized due to fast cornering.

Rpedestrians or objects are on the driver's

side of the vehicle.

If you switch to symmetrical low beam (Y page 244), pedestrians or objects on the front-passenger side of the vehicle will not be recognized instead.

It may be the case that pedestrians and other objects are inadvertently illuminated.

Activating/deactivating Night View Assist Plus with spotlight function You can only activate Night View Assist Plus with spotlight function if: Rthe SmartKey is in position 2 in the ignition

lock.

Rit is dark. Rthe "Adaptive Highbeam Assist" function is

activated via the on-board computer (Y page 344).

Rthe light switch is in position c. Rthe combination switch is pushed forward

beyond the point of resistance.

Rreverse gear has not been engaged.

X To activate: activate Adaptive Highbeam

Assist (Y page 248).

X Press button :.

The Night View Assist Plus with spotlight function display appears in the multifunction display.

Driving systems

319

the vehicle is stationary or moving slowly, you cannot check whether Night View Assist Plus with spotlight function is operating.

When you activate Night View Assist Plus with spotlight function, speed display A in the multifunction display changes. Speed display A is shown as a bar at the bottom edge of the multifunction display. This line is no longer available for basic menus. You have to deactivate Night View Assist Plus with spotlight function if you wish to change a setting using the buttons on the multifunction steering wheel. X To deactivate the spotlight function

briefly: move the combination switch back to its normal position. The spotlight function and the Adaptive Highbeam Assist are deactivated. If you push the combination switch forward beyond the point of resistance again, both systems are reactivated.

X To deactivate: press button : again. X Deactivate the Adaptive Highbeam Assist

(Y page 248).

i If you do not wish to use the spotlight