2009 Mercedes-benz C Class 4matic Owners Manual

! Always use washer solvent/antifreeze

where temperatures may fall below freezing point. Failure to do so could result in damage to the washer system/fluid reservoir.

! Only use washer fluid which is suitable for plastic lenses. Improper washer fluid can damage the plastic lenses of the headlamps.

! Do not use distilled or deionized water in the washer fluid reservoir. Otherwise, the washer fluid level sensor could be damaged.

1 Cap for washer fluid reservoir Fluid for the washer system and the headlamp cleaning system is supplied from the washer fluid reservoir. During all seasons, add MB Windshield Washer Concentrate “MB SummerFit” to water. Premix the washer fluid in a suitable container.

Operation

Engine compartment X Opening washer fluid reservoir: Pull tab

of cap 1 upwards.

X Refill the washer fluid reservoir with MB

Windshield Washer Concentrate “MB SummerFit” and water (or commercially available premixed washer solvent/ antifreeze, depending on ambient temperatures) (Y page 400).

X Closing washer fluid reservoir: Press cap

1 onto filler hole until it engages.

For more information, see “Washer system and headlamp cleaning system” (Y page 393).

259

Operation

Tires and wheels Tires and wheels Safety notes Contact an authorized Mercedes-Benz Center for information on tested and recommended rims and tires for summer and winter operation. They can also offer advice concerning tire service and purchase. G Warning! Replace rims or tires with the same designation, manufacturer and type as shown on the original part. For further information contact an authorized Mercedes-Benz Center. If incorrectly sized rims and tires are mounted, the wheel brakes or suspension components can be damaged. Also, the correct operating clearance of the wheels and the tires may no longer be correct. G Warning! Worn, old tires can cause accidents. If the tire tread is worn to minimum tread depth, or if the tires have sustained damage, replace them. When replacing rims, only use genuine Mercedes-Benz wheel bolts specified for the particular rim type. Failure to do so can

260

result in the bolts loosening and possibly an accident. Retreaded tires are not tested or recommended by Mercedes-Benz, since previous damage cannot always be recognized on retreads. The operating safety of the vehicle cannot be assured when such tires are used. G Warning! If you feel a sudden significant vibration or ride disturbance, or you suspect that possible damage to your vehicle has occurred, you should turn on the hazard warning flashers, carefully slow down, and drive with caution to an area which is a safe distance from the road. Inspect the tires and the vehicle underbody for possible damage. If the vehicle or tires appear unsafe, have the vehicle towed to the nearest authorized Mercedes-Benz Center or tire dealer for repairs. G Warning! Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You could lose control of the vehicle. Continued driving with a flat tire or driving at high

speed with a flat tire will cause excessive heat build-up and possibly a fire.

Important guidelines ROnly use sets of tires and rims of the same

type and make.

RTires must be of the correct size for the rim. RBreak in new tires for approximately

60 miles (100 km) at moderate speeds.

RRegularly check the tires and rims for

damage. Dented or bent rims can cause tire inflation pressure loss and damage to the tire beads.

RIf vehicle is heavily loaded, check tire

inflation pressure and correct as required. RDo not allow your tires to wear down too far. Adhesion properties on wet roads are sharply reduced at tread depths of less than 1/8 in (3 mm).

RWhen replacing individual tires, you should mount new tires on the front wheels first (on vehicles with same-sized wheels all around).

Tire care and maintenance G Warning! Regularly check the tires for damage. Damaged tires can cause tire inflation pressure loss. As a result, you could lose control of your vehicle. Worn, old tires can cause accidents. If the tire tread is worn to minimum tread depth, or if the tires have sustained damage, replace them. Check the tire inflation pressure at least every other week. For more information on checking tire inflation pressure, see “Recommended tire inflation pressure” (Y page 266).

Tire inspection Every time you check the tire inflation pressure, you should also inspect your tires for the following: Rexcessive treadwear (Y page 261) Rcord or fabric showing through the tire’s

rubber

Rbumps, bulges, cuts, cracks or splits in the

tread or side of the tire

Replace the tire if you find any of the above conditions. Make sure you also inspect the spare tire periodically for condition and inflation. Spare tires will age and become worn over time even if never used, and thus should be inspected and replaced when necessary.

Life of tire G Warning! Tires and spare tire should be replaced after 6 years, regardless of the remaining tread. The service life of a tire is dependent upon varying factors including but not limited to: RDriving style RTire inflation pressure RDistance driven

Tread depth G Warning! Although the applicable federal motor vehicle safety laws consider a tire to be worn when the treadwear indicators (TWI) become visible at approximately 1/16 in

Operation

Tires and wheels (1.6 mm), we recommend that you do not allow your tires to wear down to that level. As tread depth approaches 1/8 in (3 mm), the adhesion properties on a wet road are sharply reduced. Depending upon the weather and/or road surface (conditions), the tire traction varies widely. Do not allow your tires to wear down too far. Adhesion properties on wet roads are sharply reduced at tread depths of less than 1/8 in (3 mm). Treadwear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and become visible at a tread depth of approximately 1/16 in (1.6 mm), at which point the tire is considered worn and should be replaced. The recommended minimum tire tread depth for summer tires is 1/8 in (3 mm). The recommended minimum tire tread depth for winter tires is 1/6 in (4 mm).

261

Operation

Tires and wheels

1 TWI (Tread Wear Indicator) The treadwear indicator appears as a solid band across the tread.

Storing tires ! Keep unmounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease and fuels.

Cleaning tires ! Never use a round nozzle to power wash tires. The intense jet of water can result in damage to the tire. Always replace a damaged tire.

262

Direction of rotation Unidirectional tires offer added advantages, such as better hydroplaning performance. To benefit, however, you must make sure the tires rotate in the direction specified. An arrow on the sidewall indicates the intended direction of rotation (spinning) of the tire. Spare wheels may be mounted against the direction of rotation (spinning) even with a unidirectional tire for temporary use only until the regular drive wheel has been repaired or replaced. Always observe and follow applicable temporary use restrictions and speed limitations indicated on the spare wheel.

Loading the vehicle Two labels on your vehicle show how much weight it may properly carry. (1) The Tire and Loading Information placard

can be found on the driver’s door B-pillar. This placard tells you important information about the number of people that can be in the vehicle and the total weight that can be carried in the vehicle. It also contains information on the proper size and recommended tire inflation pressures for the original equipment tires on your vehicle.

(2) The certification label, also found on the driver’s door B-pillar. It tells you about the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. The certification label also tells you about the front and rear axle weight capacity, called the Gross Axle Weight Rating (GAWR). The GAWR is the total allowable weight that can be carried by a single axle (front or rear). Never exceed the GVWR or GAWR for either the front axle or rear axle.

Tire and Loading Information placard i Data shown on Tire and Loading

Information placard example are for illustration purposes only. Load limit data are specific to each vehicle and may vary from data shown in the following illustration. Refer to Tire and Loading Information placard on vehicle for actual data specific to your vehicle.

1 Load limit information on the Tire and

Loading Information placard

The Tire and Loading Information placard showing the load limit information is located on the driver’s door B-pillar (Y page 263). X Locate the statement “The combined weight of occupants and cargo should never exceed XXX kilograms or XXX lbs.”

Operation

Tires and wheels

on the Tire and Loading Information placard.

The combined weight of all occupants, cargo/luggage and trailer tongue load (if applicable) should never exceed the weight referenced in that statement.

Seating capacity The seating capacity gives you important information on the number of occupants that can be in the vehicle. Observe front and rear seating capacity. The Tire and Loading Information placard showing the seating capacity is located on the driver’s door B-pillar (Y page 263). i Data shown on Tire and Loading

Information placard example are for illustration purposes only. Seating capacity data are specific to each vehicle and may vary from data shown in the following illustration. Refer to Tire and Loading Information placard on vehicle for actual data specific to your vehicle.

263

1 Driver’s door B-pillar Following is a discussion on how to work with the information contained on the Tire and Loading Information placard with regards to loading your vehicle.

Tire and Loading Information G Warning! Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure.

X Step 1: Locate the statement “The

combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s Tire and Loading Information placard.

X Step 2: Determine the combined weight of the driver and passengers that will be riding in your vehicle.

X Step 3: Subtract the combined weight of

the driver and passengers from XXX kilograms or XXX lbs.

X Step 4: The resulting figure equals the

available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1 400 lbs and there will be five 150 lbs passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1 400 - 750 (5 x 150) = 650 lbs).

X Step 5: Determine the combined weight of

luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4.

X Step 6 (if applicable): If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle (Y page 266).

The following table shows examples on how to calculate total and cargo load capacities with varying seating configurations and number and size of occupants. The following examples use a load limit of 1 500 lbs. This is for illustration purposes only. Make sure you are using the actual load limit for your vehicle stated on the vehicle’s Tire and Loading Information placard (Y page 263).

Operation

Tires and wheels

1 Seating capacity information on the Tire

and Loading Information placard

Steps for determining correct load limit The following steps have been developed as required of all manufacturers under Title 49, Code of U.S. Federal Regulations, Part 575
pursuant to the “National Traffic and Motor Vehicle Safety Act of 1966”.

264

Operation

Tires and wheels

Available cargo/luggage and trailer tongue weight (total load limit from Tire and Loading Information placard minus combined weight of all occupants) 1 500 lbs - 750 lbs = 750 lbs

Number of occupants (driver and passengers)

Seating configuration

Occupants weight

Combined weight of all occupants

750 lbs

front: 2
rear: 3

front: 1
rear: 2

front: 1

Occupant 1: 150 lbs Occupant 2: 180 lbs Occupant 3: 160 lbs Occupant 4: 140 lbs Occupant 5: 120 lbs Occupant 1: 200 lbs Occupant 2: 190 lbs Occupant 3: 150 lbs Occupant 1: 150 lbs

540 lbs

1 500 lbs - 540 lbs = 960 lbs

150 lbs

1 500 lbs - 150 lbs = 1 350 lbs

Example Combined weight limit of occupants and cargo from Tire and Loading Information placard 1 500 lbs

1 500 lbs

1 500 lbs

The higher the weight of all occupants, the less cargo and luggage load capacity is available. For more information, see “Trailer tongue load” (Y page 266).

Certification label Even after careful determination of the combined weight of all occupants, cargo and the trailer tongue load (if applicable)

(Y page 266) as to not exceed the permissible load limit, you must make sure your vehicle never exceeds the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for either the front or rear axle. You can obtain the GVWR and GAWR from the certification label. The certification label can be found on the driver’s door B-pillar, see the “Technical data” section (Y page 377).

Gross Vehicle Weight Rating (GVWR): The total weight of the vehicle, all occupants, all cargo, and the trailer tongue load (if applicable) must never exceed the GVWR. Gross Axle Weight Rating (GAWR): The total allowable weight that can be carried by a single axle (front or rear). To assure that your vehicle does not exceed the maximum permissible weight limits (GVWR and GAWR for front and rear axle),

265

Operation

Tires and wheels have the loaded vehicle (including driver, passengers and all cargo and, if applicable, trailer fully loaded) weighed on a suitable commercial scale.

Trailer tongue load The tongue load of any trailer is an important weight to measure because it affects the load you can carry in your vehicle. If a trailer is towed, the tongue load must be added to the weight of all occupants riding and any cargo you are carrying in the vehicle. The tongue load typically is 10% of the trailer weight and everything loaded in it. Your Mercedes-Benz has been designed primarily to carry passengers and their cargo. Mercedes-Benz does not recommend trailer towing with your vehicle.

266

Recommended tire inflation pressure G Warning! Follow recommended tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc. Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure. Your vehicle is equipped with the Tire and Loading Information placard located on the driver’s door B-pillar (Y page 262).

The tire inflation pressure should be checked regularly and should only be adjusted on cold tires. The tires can be considered cold if the vehicle has been parked for at least 3 hours or driven less than 1 mile (1.6 km). Follow recommended cold tire inflation pressures listed on Tire and Loading Information placard on the driver’s door B-pillar. Keeping the tires properly inflated provides the best handling, tread life and riding comfort. In addition to the Tire and Loading Information placard on the driver’s door B-pillar, also consult the tire inflation pressure label (if available) on the inside of the filler flap for any additional information pertaining to special driving situations. For more information, see “Important notes on tire inflation pressure” (Y page 267). i Data shown on Tire and Loading

Information placard example are for illustration purposes only. Tire data are specific to each vehicle and may vary from data shown in the following illustration. Refer to Tire and Loading Information placard on vehicle for actual data specific to your vehicle.

Operation

Tires and wheels

leaking from the valves or from around the rim. Tire temperature and tire inflation pressure are also increased while driving, depending on the driving speed and the tire load. If you will be driving your vehicle at high speeds of 100 mph (160 km/h) or higher, where it is legal and conditions allow, consult the tire inflation pressure label on the inside of the fuel filler flap (if available) on how to adjust the cold tire inflation pressure. If you do not adjust the tire inflation pressure, excessive heat can build up and result in sudden tire failure. If your vehicle is not equipped with the tire inflation pressure label on the inside of the fuel filler flap, contact an authorized Mercedes-Benz Center for proper tire inflation pressure. i Driving comfort may be reduced when the

tire inflation pressure is adjusted to the value for speeds above 100 mph (160 km/h) as specified on the tire inflation pressure label located on the inside of the fuel filler flap.

Make sure to readjust the tire inflation pressure for normal driving speeds. You

should wait until the tires are cold before adjusting the tire inflation pressure. Some vehicles may have supplemental tire inflation pressure information for vehicle loads less than the maximum loaded vehicle condition. If such information is provided, it can be found on the tire inflation pressure label located on the inside of the fuel filler flap. Tire inflation pressure changes by approximately 1.5 psi (0.1 bar) per 18‡ (10†) of air temperature change. Keep this in mind when checking tire inflation pressure where the temperature is different from the outside temperature.

Potential problems associated with underinflated and overinflated tires Underinflated tires G Warning! Follow recommended tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

267

1 Tire and Loading Information placard with

recommended cold tire inflation pressures

The Tire and Loading Information placard lists the recommended cold tire inflation pressures for maximum loaded vehicle weight. The tire inflation pressures listed apply to the tires installed as original equipment.

Important notes on tire inflation pressure G Warning! If the tire inflation pressure drops repeatedly, check the tires for punctures from foreign objects and/or whether air is

Operation

Tires and wheels Underinflated tires can Rcause excessive and uneven tire wear Radversely affect fuel economy Rlead to tire failure from being overheated Radversely affect handling characteristics

Overinflated tires G Warning! Follow recommended tire inflation pressures. Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc. Overinflated tires can Radversely affect handling characteristics Rcause uneven tire wear Rbe more prone to damage from road

hazards

Radversely affect ride comfort Rincrease stopping distance

268

Checking tire inflation pressure Safety notes G Warning! Follow recommended tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc. Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure. Check the tire inflation pressure at least every other week.

Check and adjust the tire inflation pressure when the tires are cold. The tires can be considered cold if the vehicle has been parked for at least 3 hours or driven less than 1 mile (1.6 km). If you check the tire inflation pressure when the tires are warm (the vehicle has been driven for several miles or sitting less than 3 hours), the reading will be approximately 4 psi (0.3 bar) higher than the cold reading. This is normal. Do not let air out to match the specified cold tire inflation pressure. Otherwise, the tire will be underinflated.

Checking tire inflation pressure manually Follow the steps below to achieve correct tire inflation pressure: X Remove the cap from the valve on one tire. X Firmly press a tire gauge onto the valve. X Read the tire inflation pressure on the tire

gauge and check against the recommended tire inflation pressure on the Tire and Loading Information placard on the driver’s door B-pillar (Y page 263). If necessary, add air to achieve the recommended tire inflation pressure.

X If you have overfilled the tire, release tire

inflation pressure by pushing the metal

stem of the valve with e.g. a tip of a pen. Then recheck the tire inflation pressure with the tire gauge. X Install the valve cap. X Repeat this procedure for each tire.

Run Flat Indicator (Canada only) While the vehicle is being driven, the Run Flat Indicator monitors the set tire inflation pressures by evaluating each wheel’s rotational speed. This allows the system to detect a significant loss of pressure in a tire. If a wheel’s rotational speed changes due to falling tire inflation pressure, you will see a corresponding warning message in the multifunction display. The Run Flat Indicator may function in a restricted manner or with a delay Rwhen snow chains are mounted to the

vehicle

Rin the presence of ice and snow Rwhen you are driving on a loose surface

(e.g. sand or gravel)

Rwhen you are driving in a very sporty

manner (involving rapid acceleration or high speeds in curves)

Rwhen you are driving with a loaded roof

rack or heavily laden vehicle G Warning! When the multifunction display shows the message Check Tire Pressure Soon, one or more of your tires are significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper tire inflation pressure as indicated on the vehicle’s Tire and Loading Information placard or, if available, on the tire inflation pressure label. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare, should be checked every other week when cold and set to the recommended tire inflation pressure as specified on the Tire and Loading Information placard on the driver’s door B-pillar or, if available, on the tire inflation pressure label located on the inside of the fuel filler flap.

Operation

Tires and wheels i The recommended tire inflation pressures

for your vehicle can be found on the Tire and Loading Information placard located on the driver’s door B-pillar (Y page 263) or, if available, on the tire inflation pressure label on the on the inside of the fuel filler flap. The tire inflation pressures are not listed in the Operator’s Manual. G Warning! The Run Flat Indicator does not provide a warning for wrongly selected tire inflation pressures. Always adjust tire inflation pressure according to the Tire and Loading Information placard on the driver’s door B-pillar or, if available, on the tire inflation pressure label located on the inside of the fuel filler flap. The Run Flat Indicator does not replace regular checks of the tire inflation pressures since a gradual pressure loss in more than one tire cannot be detected by the Run Flat Indicator. The Run Flat Indicator is not able to issue a warning due to a sudden dramatic loss of tire inflation pressure (e.g. tire blowout caused by a foreign object). In this case bring the vehicle to a halt by carefully

269

Operation

Tires and wheels applying the brakes and avoiding abrupt steering maneuvers. Restarting the Run Flat Indicator The Run Flat Indicator must be restarted in the following situations: Rafter you have changed the tire inflation

pressure

Rafter you have replaced the wheels or tires Rafter you have installed new wheels or tires X Using the Tire and Loading Information placard on the driver’s door B-pillar or, if available, the tire inflation pressure label on the inside of the fuel filler flap, make sure the tire inflation pressure of all four tires is correct. G Warning! The Run Flat Indicator can only warn you in a reliable manner if you have set the correct tire inflation pressures for each tire. If an incorrect tire inflation pressure was set, the system will monitor the pressure according to the incorrect value.

270

X Switch on the ignition. X Press button ( or & on the

multifunction steering wheel to select the Service menu.

X Press button $ or % on the

multifunction steering wheel to select TIRE PRESS..

X Press button # on the multifunction

steering wheel to confirm. The following message appears in the multifunction display: Run Flat Indicator Active Press 'OK' to Restart

X Press button #.

The following message will appear in the multifunction display: Tire Pressure Now OK? Cancel Yes

X If you wish to confirm: Press button

$ or % to select Yes.

X Press button #.

The following message will appear in the multifunction display: Run Flat Indicator Restarted

After a certain “learning phase”, the Run Flat Indicator checks the set pressure values for all four tires.

X If you wish to cancel: Press button $

or % to select Cancel.

X Press button # to confirm.

The previous settings remain unchanged.

Tire Pressure Monitoring System (TPMS), (USA only) Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS). It measures the tire inflation pressure in the vehicle’s tires and issues warnings in case of pressure loss. The Tire Pressure Monitoring System (TPMS) is equipped with a combination low tire pressure/TPMS malfunction telltale in the instrument cluster. Depending on how the telltale illuminates, it indicates a low tire pressure condition or a malfunction in the TPMS system itself: RIf the telltale illuminates continuously, one

or more of your tires are significantly

underinflated. There is no malfunction in the TPMS.

RIf the telltale flashes for 60 seconds and then stays illuminated, the TPMS system itself is not operating properly.

The TPMS only functions on wheels that are equipped with the proper electronic sensors. It monitors the tire inflation pressure, as selected by the driver, in all four tires. A warning is issued to alert you to a decrease in pressure in one or more of the tires. G Warning! The TPMS does not indicate a warning for wrongly selected inflation pressures. Always adjust tire inflation pressure according to the Tire and Loading Information placard or, if available, on the supplemental tire inflation pressure information on the inside of the fuel filler flap. The TPMS is not able to issue a warning due to a sudden dramatic loss of pressure (e.g. tire blowout caused by a foreign object). In this case bring the vehicle to a halt by carefully applying the brakes and avoiding abrupt steering maneuvers.

G Warning! Each tire, including the spare (if provided), should be checked every other week when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the Tire and Loading Information placard on the driver’s door B-pillar or, if available, the tire inflation pressure label on the inside of the fuel filler flap. If your vehicle has tires of a different size than the size indicated on the Tire and Loading Information placard or, if available, the tire inflation pressure label, you should determine the proper tire inflation pressure for those tires. As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires are significantly underinflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the

Operation

Tires and wheels

vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately 1 minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of incompatible replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after

271

Operation

Tires and wheels replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.

i If a condition causing the TPMS to

malfunction develops, it may take up to 10 minutes for the system to signal a malfunction using the TPMS telltale flashing and illumination sequence. The telltale extinguishes after a few minutes driving if the malfunction has been corrected.

i Operating radio transmission equipment (e.g. wireless headsets, two-way radios) in or near the vehicle could cause the TPMS to malfunction.

i This device complies with Part 15 of the

FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful

interference, and this device must accept any interference received, including interference that may cause undesired.

2.

272

Any unauthorized modification to this device could void the user’s authority to operate the equipment.

Tire inflation pressure warnings If the system detects a significant loss of tire inflation pressure in one or more than one tire, a message appears in the multifunction display. In addition, an acoustic warning sounds and the low tire pressure telltale in the instrument cluster comes on.

Example illustration Restarting the TPMS G Warning! It is the driver’s responsibility to set the tire inflation pressure to the recommended cold tire inflation pressure. Underinflated tires affect the ability to steer or brake the vehicle. You might lose control over the vehicle.

When you restart the TPMS, the system sets new reference values for each tire. The TPMS must be restarted when you have adjusted the tire inflation pressure to a new level (e.g. because of different load or driving conditions). The TPMS is then recalibrated to the current tire inflation pressures. Restart the TPMS after adjusting the tire inflation pressure to the inflation pressure recommended for the vehicle operating condition. Tire pressure should only be adjusted on cold tires. Observe the recommended tire inflation pressure on the Tire and Loading Information placard on the driver’s door B-pillar. Some vehicles may have supplemental tire pressure information for driving at high speeds or for vehicle loads less than the maximum loaded vehicle condition. If such information is provided, it can be found on the inside of the fuel filler flap. X Using the Tire and Loading Information

placard on the driver’s door B-pillar (Y page 263) or, if available, the supplemental tire inflation pressure information on the inside of the fuel filler flap, make sure the tire inflation pressure of all four tires is correct.

X Switch on the ignition.

X Press button ( or & on the

multifunction steering wheel to select the Service menu (Y page 144).

X Press the button $ or% on the

multifunction steering wheel to select Tire Pressure.

X Press button # on the multifunction

steering wheel to confirm. The following message appears in the multifunction display: Tire Pressure Monitor Active

X Press button %.

The following message appears in the multifunction display: Use Current Pressures as New Reference Values Press 'OK' to Confirm

X If you wish to confirm: Press button

#. The following message appears in the multifunction display: Tire Press. Monitor Restarted After driving a few minutes the system verifies that the current tire inflation

Operation

Tires and wheels

pressures are within the system’s specified range. Afterwards, the current tire inflation pressures are accepted as reference values and then monitored.

X If you wish to cancel: Press button

L.

Tire labeling Besides tire name (sales designation) and manufacturer name, a number of markings can be found on a tire. Following are some explanations for the markings on your vehicle’s tires:

1 Uniform Tire Quality Grading Standards

2 DOT, Tire Identification Number

(Y page 279)

(Y page 277)

3 Maximum tire load (Y page 278) 4 Maximum tire inflation pressure

(Y page 278) 5 Manufacturer 6 Tire ply material (Y page 280) 7 Tire size designation, load and speed

rating (Y page 274)

8 Load identification (Y page 276) 9 Tire name

273

Operation

Tires and wheels i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration. For more information, see “Rims and tires” (Y page 382).

Tire size designation, load and speed rating

1 Tire width 2 Aspect ratio in % 3 Radial tire code 4 Rim diameter 5 Tire load rating 6 Tire speed rating

274

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

General: Depending on the design standards used, the tire size molded into the sidewall may have no letter or a letter preceding the tire size designation. No letter preceding the size designation (as illustrated above): Passenger car tire based on European design standards. Letter “P” preceding the size designation: Passenger car tire based on U.S. design standards. Letter “LT” preceding the size designation: Light Truck tire based on U.S. design standards. Letter “T” preceding the size designation: Temporary spare tires which are high pressure compact spares designed for temporary emergency use only. Tire width Tire width 1 indicates the nominal tire width in millimeters.

Aspect ratio Aspect ratio 2 is the dimensional relationship between tire section height and section width and is expressed in percentage. The aspect ratio is arrived at by dividing section height by section width. Tire code Tire code 3 indicates the tire construction type. The “R” stands for radial tire type. Letter “D” means diagonal or bias ply construction; letter “B” means belted-bias ply construction. At the tire manufacturer’s option, any tire with a speed capability above 149 mph (240 km/h) can include a “ZR” in the size designation (for example: 245/40 ZR 18). For additional information, see “Tire speed rating” (Y page 275). Rim diameter Rim diameter 4 is the diameter of the bead seat, not the diameter of the rim edge. The rim diameter is indicated in inches (in). Tire load rating G Warning! The tire load rating must always be at least half of the GAWR of your vehicle. Otherwise, tire failure may be the result

which may cause an accident and/or serious injury to you or others. Always replace rims and tires with the same designation, manufacturer and type as shown on the original part. G Warning! Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure. Tire load rating 5 is a numerical code associated with the maximum load a tire can support. For example, a load rating of 91 corresponds to a maximum load of 1356 lb (615 kg) the tire is designed to support. See also “Maximum tire load” (Y page 278) where the maximum load associated with the load index is indicated in kilograms and lbs. For additional information on tire load rating, see “Load identification” (Y page 276).

Tire speed rating G Warning! Even when permitted by law, never operate a vehicle at speeds greater than the maximum speed rating of the tires. Exceeding the maximum speed for which tires are rated can lead to sudden tire failure, causing loss of vehicle control and possibly resulting in an accident and/or serious personal injury and possible death, for you and for others. Regardless of the tire speed rating, local speed limits should be obeyed. Use prudent driving speeds appropriate to prevailing conditions. Tire speed rating 6 indicates the approved maximum speed for the tire. Summer tires Index

Speed rating up to 100 mph (160 km/h) up to 106 mph (170 km/h) up to 112 mph (180 km/h) up to 118 mph (190 km/h) up to 130 mph (210 km/h)

Operation

Tires and wheels

Index ZR...Y ZR...(..Y) ZR

Speed rating up to 149 mph (240 km/h) up to 168 mph (270 km/h) up to 186 mph (300 km/h) up to 186 mph (300 km/h) above 186 mph (300 km/h) above 149 mph (240 km/h)

RAt the tire manufacturer’s option, any tire

with a speed capability above 149 mph (240 km/h) can include a “ZR” in the size designation (for example: 245/40 ZR18). To determine the maximum speed capability of the tire, the service description for the tire must be referred to. The service description is comprised of tire load rating 5 and tire speed rating 6. If your tire includes “ZR” in the size designation and no service description is given, the tire manufacturer must be consulted for the maximum speed capability. If a service description is given, the speed capability is limited by the speed symbol in the service description. Example:

275

Operation

Tires and wheels

245/40 ZR18 97Y. In this example, “97Y” is the service description. The letter “Y” designates the speed rating and the speed capability of the tire is limited to 186 mph (300 km/h).

RAny tire with a speed capability above

186 mph (300 km/h) must include a “ZR” in the size designation AND the service description must be placed in parenthesis. Example: 275/40 ZR 18 (99Y). The “(Y)” speed rating in parenthesis designates the maximum speed capability of the tire as being above 186 mph (300 km/h). Consult the tire manufacturer for the actual maximum permissible speed of the tire.

All-season and winter tires Index Speed rating Q M+S16 up to 100 mph (160 km/h) up to 118 mph (190 km/h) T M+S16
H M+S16 up to 130 mph (210 km/h) up to 149 mph (240 km/h) V M+S16

i Not all M+S rated tires provide special winter performance. Make sure the tires

16 or M+S.for winter tires 276

you use show M+S and the mountain/ snowflake.marking on the tire sidewall. These tires meet specific snow traction performance requirements of the Rubber Manufacturers Association (RMA) and the Rubber Association of Canada (RAC) and have been designed specifically for use in snow conditions.

An electronic speed limiter prevents your vehicle from exceeding a speed of: RAll models except C 63 AMG:

130 mph (210 km/h)

RC 63 AMG:

155 mph (250 km/h)

RC 63 AMG with increased top speed:

174 mph (280 km/h)

The factory equipped tires on your vehicle may have a tire speed rating above the maximum speed permitted by the electronic speed limiter. Make sure your tires have the required tire speed rating as specified for your vehicle in the “Technical data” section (Y page 382), for example when purchasing new tires. If you are uncertain about the correct reading of the information given on a tire’s sidewall,

any authorized Mercedes-Benz Center will be glad to assist you.

Load identification

1 Load identification

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

In addition to tire load rating, special load identification 1 may be molded into the tire sidewall following the letter designating the tire speed rating 6 (Y page 274).

RNo specification given: absence of any text

(like in above example) indicates a standard load (SL) tire.

RXL or Extra Load: designates an extra load

(or reinforced) tire.

RLight Load: designates a light load tire. RC, D, E: designates load range associated with the maximum load a tire can carry at a specified pressure.

DOT, Tire Identification Number (TIN) U.S. tire regulations require each new tire manufacturer or tire retreader to mold a TIN into or onto a sidewall of each tire produced. The TIN is a unique identifier which facilitates efforts by tire manufactures to notify purchasers in recall situations or other safety matters concerning tires and gives purchasers the means to easily identify such tires. The TIN is comprised of “Manufacturer’s identification mark”, “Tire size”, “Tire type code” and “Date of manufacture”.

1 DOT 2 Manufacturer’s identification mark 3 Tire size 4 Tire type code (at the option of the tire

manufacturer)

5 Date of manufacture

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

DOT (Department of Transportation) Tire branding symbol 1 denotes that the tire meets requirements of the U.S. Department of Transportation.

Operation

Tires and wheels

Manufacturer’s identification mark Manufacturer’s identification mark 2
denotes the tire manufacturer. New tires have a mark with two symbols. Retreaded tires have a mark with four symbols. For more information on retreaded tires, see (Y page 260).

Tire size Code 3 indicates the tire size.

Tire type code Tire type code 4 may, at the option of the manufacturer, be used as a descriptive code for identifying significant characteristics of the tire.

Date of manufacture The date of manufacture 5 identifies the week and year of manufacture. The first two figures identify the week, starting with “01” to represent the first full week of the calendar year. The second two figures represent the year.

277

Operation

Tires and wheels For example, “3202” represents the 32nd week of 2002.

Maximum tire load G Warning! Do not overload the tires by exceeding the specified load limit as indicated on the Tire and Loading Information placard on the driver’s door B-pillar. Overloading the tires can overheat them, possibly causing a blowout. Overloading the tires can also result in handling or steering problems, or brake failure.

1 Maximum tire load rating

i For illustration purposes only. Actual data

on tires are specific to each vehicle and

278

may vary from data shown in above illustration.

The maximum tire load is the maximum weight the tires are designed to support. For more information on tire load rating, see (Y page 274). For information on calculating total and cargo load capacities, see (Y page 264).

Maximum tire inflation pressure G Warning! Never exceed the maximum tire inflation pressure. Follow recommended tire inflation pressures. Do not underinflate tires. Underinflated tires wear excessively and/or unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated. Do not overinflate tires. Overinflated tires can adversely affect handling and ride comfort, wear unevenly, increase stopping distance, and result in sudden deflation (blowout) because they are more likely to become punctured or damaged by road debris, potholes etc.

1 Maximum permissible tire inflation

pressure

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

This is the maximum permissible tire inflation pressure for the tire. Always follow the recommended tire inflation pressure (Y page 266) for proper tire inflation.

Uniform Tire Quality Grading Standards The Uniform Tire Quality Grading is a U.S. Government requirement designed to give drivers consistent and reliable information regarding tire performance. Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. Although not a Government of Canada requirement, all tires made for sale in North America have these grades branded on the sidewall.

1 Treadwear 2 Traction 3 Temperature resistance

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

Quality grades can be found, where applicable, on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200

Temperature

Traction AA

All passenger car tires must conform to federal safety requirements in addition to these grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified U.S. Government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits,

Operation

Tires and wheels

service practices and differences in road characteristics and climate.

Traction G Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. G Warning! If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution. The safe speed on a wet, snow covered or icy road is always lower than on a dry road. You should pay particular attention to the condition of the road whenever the outside temperature is close to the freezing point.

279

Operation

Tires and wheels Mercedes-Benz recommends winter tires (Y page 284) with a minimum tread depth of approximately 1/6 in (4 mm) on all four wheels for the winter season to ensure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance compared to summer tires. Stopping distance, however, is still considerably greater than when the road is not covered with snow or ice. Exercise appropriate caution. ! Avoid spinning of a drive wheel. This may

cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

Temperature G Warning! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause excessive heat build-up and possible tire failure. The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to 280

dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

Tire ply material

i For illustration purposes only. Actual data

on tires are specific to each vehicle and may vary from data shown in above illustration.

This marking tells you about the type of cord and number of plies in the sidewall and under the tread.

Tire and loading terminology Accessory weight The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-installed equipment (whether installed or not).

Air pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi), or kilopascal (kPa) or bar.

1 Plies in sidewall 2 Plies under tread

Aspect ratio Dimensional relationship between tire section height and section width expressed in percentage.

DOT (Department of Transportation) A tire branding symbol which denotes the tire meets requirements of the U.S. Department of Transportation.

Bar Another metric unit for air pressure. There are 14.5038 pounds per square inch (psi) to 1 bar; there are 100 kilopascals (kPa) to 1 bar.

Bead The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.

Cold tire inflation pressure Tire inflation pressure when your vehicle has been sitting for at least 3 hours or driven no more than 1 mile (1.6 km).

Curb weight The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional optional equipment, but without passengers and cargo.

GAWR (Gross Axle Weight Rating) The GAWR is the maximum permissible axle weight. The gross vehicle weight on each axle must never exceed the GAWR for the front and rear axle indicated on the certification label located on the driver’s door B-pillar.

GVW (Gross Vehicle Weight) The GVW comprises the weight of the vehicle including fuel, tools, spare wheel, installed accessories, passengers and cargo and, if applicable, trailer tongue load. The GVW must never exceed the GVWR indicated on the certification label located on the driver’s door B-pillar.

GVWR (Gross Vehicle Weight Rating) This is the maximum permissible vehicle weight of the fully loaded vehicle (weight of the vehicle including all options, passengers, fuel, and cargo and, if applicable, trailer

Operation

Tires and wheels tongue load). It is indicated on certification label located on the driver’s door B-pillar.

Kilopascal (kPa) The metric unit for air pressure. There are 6.9 kPa to 1 psi; another metric unit for air pressure is bar. There are 100 kilopascals (kPa) to 1 bar.

Maximum load rating The maximum load in kilograms and pounds that can be carried by the tire.

Maximum loaded vehicle weight The sum of curb weight, accessory weight, total load limit, and production options weight.

Maximum permissible tire inflation pressure This number is the greatest amount of air pressure that should ever be put in the tire.

281

Operation

Tires and wheels Normal occupant weight The number of occupants the vehicle is designed to seat, multiplied by 68 kilograms (150 lb).

Occupant distribution The distribution of occupants in a vehicle at their designated seating positions.

Production options weight The combined weight of those installed regular production options weighing over 5 lbs (2.3 kilograms) in excess of those standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim.

PSI (Pounds per square inch) A standard unit of measure for air pressure.

Recommended tire inflation pressure The recommended tire inflation pressure for normal driving conditions is listed on the Tire and Loading Information placard located on the driver’s door B-pillar and provides best

282

handling, tread life and riding comfort. If so equipped, supplemental information pertaining to special driving situations can be found on the tire inflation pressure label on the inside of the fuel filler flap.

Rim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated.

Sidewall The portion of a tire between the tread and the bead.

TIN (Tire Identification Number) Unique identifier which facilitates efforts by tire manufacturers to notify purchasers in recall situations or other safety matters concerning tires and gives purchasers the means to easily identify such tires. The TIN is comprised of “Manufacturer’s identification mark”, “Tire size”, “Tire type code” and “Date of manufacture”.

Tire load rating Numerical code associated with the maximum load a tire can support.

Tire ply composition and material used This indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and sidewall, which include steel, nylon, polyester, and others.

Tire speed rating Part of tire designation; indicates the speed range for which a tire is approved.

Total load limit Rated cargo and luggage load plus 68 kilograms (150 lb) times the vehicle’s designated seating capacity.

Traction Force exerted by the vehicle on the road via the tires. The amount of grip provided.

Tread The portion of a tire that comes into contact with the road.

Treadwear indicators Narrow bands, sometimes called “wear bars” that show across the tread of a tire when only 1/16 in (1.6 mm) of tread remains.

Uniform Tire Quality Grading Standards A tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear. Ratings are determined by tire manufacturers using U.S. government testing procedures. The ratings are molded into the sidewall of the tire.

Vehicle maximum load on the tire Load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing it by two.

Rotating tires G Warning! Rotate front and rear wheels only if the tires are of the same dimension. If your vehicle is equipped with mixed-size tires (different tire dimensions front vs. rear), tire rotation is not possible. G Warning! Have the tightening torque checked after changing a wheel. Wheels could become loose if not tightened with a torque of 96 lb-ft (130 Nm). Only use genuine Mercedes-Benz wheel bolts specified for your vehicle’s rims. Tire rotation can be performed on vehicles with tires of the same dimension all around. If your vehicle is equipped with tires of the same dimension all around, tires can be rotated, observing a front-to-rear rotation pattern that will maintain the intended rotation (spinning) direction of the tire (Y page 262). In some cases, such as when your vehicle is equipped with mixed-size tires (different tire dimension front vs. rear), tire rotation is not possible.

Operation

Tires and wheels

If applicable to your vehicle’s tire configuration, tires can be rotated according to the tire manufacturer’s recommended intervals in the tire manufacturer’s warranty pamphlet located in your vehicle literature portfolio. If none is available, tires should be rotated every 3 000 to 6 000 miles (5 000 to 10 000 km), or sooner if necessary, according to the degree of tire wear. The same rotation (spinning) direction must be maintained. Rotate tires before the characteristic tire wear pattern becomes visible (shoulder wear on front tires and tread center wear on rear tires). Thoroughly clean the mounting face of wheels and brake disks, i.e. the inner side of the wheels/tires, during each rotation. Check for and ensure proper tire inflation pressure. For information on wheel change, see “Flat tire” (Y page 360).

283

Operation

Winter driving Winter driving General information Have your vehicle winterized at an authorized Mercedes-Benz Center.

Winter tires G Warning! Winter tires with a tread depth of less than 1/6 in (4 mm) must be replaced. They are no longer suitable for winter operation. G Warning! If you use your spare wheel when winter tires are fitted on the other wheels, be aware that the difference in tire characteristics may very well impair turning stability and that overall driving stability may be reduced. Adapt your driving style accordingly. Have the spare wheel replaced by regular road wheel with a winter tire at the nearest authorized Mercedes-Benz Center. Always use winter tires at temperatures below 45‡ (7†) and whenever wintry road conditions prevail. Not all M+S rated tires provide special winter performance. Make

284

sure the tires you use show the mountain/ snowflake.marking on the tire sidewall. These tires meet specific snow traction performance requirements of the Rubber Manufacturers Association (RMA) and the Rubber Association of Canada (RAC) and have been designed specifically for use in snow conditions. Use of winter tires is the only way to achieve the maximum effectiveness of your vehicle’s driving safety systems such as the ABS and the ESP® in winter operation. For safe handling, make sure all mounted winter tires are of the same make and have the same tread design. For information on winter tires for your vehicle model, see the “Technical data” section (Y page 382). Always observe the speed rating of the winter tires installed on your vehicle. If the maximum speed for which your tires are rated is below the speed rating of your vehicle, you must place a notice to this effect where it will be seen by the driver. Such notices are available at your tire dealer or any authorized Mercedes-Benz Center.

Snow chains ! Some tire sizes do not leave adequate clearance for snow chains. To help avoid serious damage to your vehicle or tires, make sure the use of snow chains is permissible as specified in the “Technical data” section of this Operator’s Manual.

Snow chains should only be driven on snow- covered roads at speeds not to exceed 30 mph (50 km/h). Remove chains as soon as possible when driving on roads without snow. Observe the following guidelines when using snow chains: RUse of snow chains is not permissible with all wheel/tire combinations (Y page 382).

RUse snow chains in pairs and on rear

wheels only. Follow the manufacturer’s mounting instructions.

! If snow chains are mounted to the front wheels, they may scrape against the body or axle components. The tires or the vehicle could be damaged as a result.

ROnly use snow chains that are approved by Mercedes-Benz. Any authorized Mercedes-

Benz Center will be glad to advise you on this subject.

RUse of snow chains may be prohibited

depending on location. Always check local and state laws before installing snow chains.

RDo not use snow chains on the spare wheel. i When driving with snow chains, you may

wish to switch off the ESP® (Y page 68) before setting the vehicle in motion. This will improve the vehicle’s traction.

Winter driving instructions G Warning! If the vehicle becomes stuck in snow, make sure snow is kept clear of the exhaust pipe and from around the vehicle with the engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death. To assure sufficient fresh air ventilation, open a window slightly on the side of the vehicle not facing the wind.

G Warning! The outside temperature indicator is not designed to serve as an ice-warning device and is therefore unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. The road may still be icy, especially in wooded areas or on bridges. G Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control. The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, shift the automatic transmission to neutral position N or declutch in case of manual transmission. Try to keep the vehicle under control by corrective steering action.

Operation

Winter driving

i For information on driving with snow

chains, see “Snow chains” (Y page 284).

Road salts and chemicals can adversely affect braking efficiency. Increased pedal force may become necessary to produce the normal brake effect. Depressing the brake pedal periodically when traveling at length on salt-strewn roads can bring road-salt-impaired braking efficiency back to normal. If the vehicle is parked after being driven on salt-treated roads, the braking efficiency should be tested as soon as possible after driving is resumed. G Warning! Make sure not to endanger any other road users when carrying out these braking maneuvers.

285

Operation

Driving instructions Driving instructions Drive sensibly – save fuel To save fuel you should: RKeep tires at the recommended inflation

pressures.

RRemove unnecessary loads. RRemove roof rack when not in use. RAllow engine to warm up under low load

use.

RAvoid frequent acceleration and

deceleration.

RHave all maintenance work performed at the intervals specified in the Maintenance Booklet and as required by the Maintenance system. Contact an authorized Mercedes-Benz Center.

Fuel consumption is also increased by driving in cold weather, in stop-and-go traffic, on short trips and in mountainous areas.

286

Drinking and driving G Warning! Drinking and driving and/or taking drugs and driving are very dangerous combinations. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgment. The possibility of a serious or even fatal accident are greatly increased when you drink or take drugs and drive. Do not drink or take drugs and drive or allow anyone to drive who has been drinking or taking drugs.

Pedals G Warning! Make sure absolutely no objects are obstructing the pedals’ range of movement. Keep the driver’s footwell clear of all obstacles. If there are any floormats or carpets in the footwell, make sure that the pedals still have sufficient clearance. During sudden driving or braking maneuvers, the objects could get caught between the pedals. You could then no

longer brake or accelerate. This could lead to accidents and injury.

Power assistance G Warning! There is no power assistance for the steering and the service brake when the engine is not running. Steering and braking requires significantly more effort and you could lose control of the vehicle and cause an accident as a result. Do not turn off the engine while the vehicle is in motion.

Brakes Downhill grades ! When driving down long and steep

grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces wear. When using the engine’s braking power, a drive wheel may not spin for an extended period of time, e.g. on slippery road

surfaces. This may cause serious damage to the drivetrain which is not covered by the Mercedes-Benz Limited Warranty.

Continuous or hard braking G Warning! Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads. It can also result in the brakes overheating, thereby significantly reducing their effectiveness. It may not be possible to stop the vehicle in sufficient time to avoid an accident. After hard braking, it is advisable to drive on for some time, rather than immediately park, so that the air stream will cool down the brakes faster.

Wet roads G Warning! After driving in heavy rain for some time without applying the brakes or through water deep enough to wet brake components, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain

expected brake effect. Maintain a safe distance from vehicles in front. To help prevent brake disk corrosion after driving on wet or salt-covered roads, it is advisable to brake the vehicle with considerable force prior to parking. The heat generated serves to dry the brakes.

Salt-covered roads G Warning! A layer of salt on the brake discs and the brake linings may cause a delay in the braking effect, resulting in a significantly increased braking distance, which could lead to an accident. To avoid this danger, you should: Roccasionally brake carefully when you

are driving on salt-covered roads, so that any layer of salt that may have built up on the brake discs and the brake linings is removed without putting other road users at risk

Rmaintain a greater distance to the vehicle

ahead and drive with particular care

Rcarefully apply the brakes at the end of a trip and immediately after commencing a

Operation

Driving instructions

new trip, so that salt residues are removed from the brake disc

Brake service ! The brake fluid level in the reservoir may be too low if the red brake warning lamp in the instrument cluster comes on while the engine is running and an acoustic warning sounds. Observe additional messages in the multifunction display that may appear. Brake pad wear or a leak in the system may be the reason for low brake fluid in the reservoir. Have the brake system inspected immediately. Contact an authorized Mercedes-Benz Center.

All checks and service work on the brake system should be carried out by qualified technicians only. Contact an authorized Mercedes-Benz Center. Only install brake pads and use brake fluid recommended by Mercedes-Benz. G Warning! If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent

287

Operation

Driving instructions that safe braking is substantially impaired. This could result in an accident.

! Vehicles with 4MATIC:

Only conduct operational or performance tests on a two-axle dynamometer. If such tests are necessary, contact an authorized Mercedes-Benz Center. You could otherwise seriously damage the brake system or the transfer case which is not covered by the Mercedes-Benz Limited Warranty.

! Vehicles with 4MATIC:

Because the ESP® operates automatically, the engine and ignition must be shut off (SmartKey in starter switch position 0 or 1 or KEYLESS-GO start/stop button in position 0 or 1) when the parking brake is being tested on a brake test dynamometer. Active braking action through the ESP® may otherwise seriously damage the brake system which is not covered by the Mercedes-Benz Limited Warranty.

! Vehicles without 4MATIC: