2013 Jeep Grand Cherokee Owners Manual

Download PDF Manual
seated properly, or if items are positioned in the area where the SABIC inflates. This especially applies to children. The SABIC is only about 3-1/2 in (9 cm) thick when it is inflated. Because air bag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of whether or not an air bag should have deployed. NOTE: In a rollover the pretensioners and/or SAB and SABIC air bags, and driver/passenger knee air bags may deploy on both sides of the vehicle. Front And Side Impact Sensors — If Equipped In front and side impacts, impact sensors — if equipped can aid the ORC in determining appropriate response to impact events. Enhanced Accident Response System In the event of an impact causing air bag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 event the ORC will determine whether to have the Enhanced Accident Response System perform the follow- ing functions: • Cut off fuel to the engine. • Flash hazard lights as long as the battery has power or • Turn on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. until the ignition key is turned off. • Unlock the doors automatically. In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be changed from IGN ON to IGN OFF. If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may occur: • The nylon air bag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the air bags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retrac- tor assemblies replaced by an authorized dealer im- mediately. Also, have the Occupant Restraint Con- troller (ORC) system serviced as well. Maintaining Your Air Bag System WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • It is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. (Continued) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer. Only manufacturer approved seat accessories may be used. If it is necessary to modify the air bag system for persons with dis- abilities, contact your authorized dealer. 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light You will want to have the air bags ready to inflate for your protection in a collision. The Air Bag Warning Light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. While the air bag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the air bag system immediately. • The Air Bag Warning Light does not come on during the four to eight seconds when the ignition is first cycled to the ON/RUN. • The Air Bag Warning Light remains on after the four to • The Air Bag Warning Light comes on intermittently or eight-second interval. remains on while driving. NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per- formed. The EDR is designed to record data related to were buckled/fastened; vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as: • How various systems in your vehicle were operating; • Whether or not the driver and passenger safety belts • How far (if at all) the driver was depressing the accelerator and/or brake pedal; and, • How fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and injuries occur. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are re- corded. However, other parties, such as law enforcement, THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 could combine the EDR data with the type of personally identifying data routinely acquired during a crash investi- gation. To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the EDR. Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’s Manual to make sure you have the correct seat for your child. Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/ eng/roadsafety/safedrivers-childsafety-index-53.htm WARNING! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. Summary Of Recommendations For Restraining Children In Vehicles THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Child Size, Height, Weight or Age Recommended Type of Child Restraint Infants and Toddlers Small Children Larger Children Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Either an Infant Carrier or a Convertible Child Restraint, facing rearward in the rear seat of the vehicle Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt Forward-Facing Child Restraint with a five-point Harness, facing forward in the rear seat of the vehicle Belt Positioning Booster Seat and the vehicle seat belt, seated in the rear seat of the vehicle Children Too Large for Child Restraints Children 12 years old or younger, who have out-grown the height or weight limit of their booster seat Vehicle Seat Belt, seated in the rear seat of the vehicle 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearward- facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. Convertible child seats can be used either rearward- facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward- facing direction than infant carriers do, so they can be used rearward-facing by children who have outgrown their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they reach the highest weight or height allowed by their convertible child seat. WARNING! • Never place a rear facing infant seat in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • Only use a rearward-facing child restraint in a rear seat. Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward- facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direc- tion are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat. Children should remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. is above the All children whose weight or height forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • When your child restraint is not in use, secure it in the vehicle with the seat belt or LATCH anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal injury. 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether the child can use the vehicle’s seat belt alone: 1. Can the child sit all the way back against the back of the vehicle seat? 2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check belt fit peri- odically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Recommendations For Attaching Child Restraints THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Use any attachment method shown with an “X” Below LATCH – Lower Anchors Seat Belt Only Only LATCH – Lower Anchors + Top Tether Anchor Seat Belt + Top Tether Anchor 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position. These anchorages are used to install LATCH-equipped child seats without using the vehicle’s seat belts. Some seating positions may have a top tether anchorage but no lower anchorages. In these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE limit (child’s is the weight What weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg). Can the LATCH anchorages and the seat belt be used together to attach a rear-facing or forward- facing child restraint? Can a child seat be installed in the center position using the inner LATCH lower anchorages? No No Do not use the seat belt when you use the LATCH anchorage system to attach a rear-facing or forward- facing child restraint. Use the seat belt and tether anchor to install a child seat in the center seating position. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Can two child restraints be attached using a common lower LATCH anchorage? Can the rear-facing child restraint touch the back of the front passenger seat? No Yes Can the head restraints be removed? Yes, center position only. Never “share” a LATCH anchorage with two or more child restraints. If the center position does not have dedicated LATCH lower anchor- ages, use the seat belt to install a child seat in the center position next to a child seat using the LATCH anchorages in an outboard position. The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion. 60/40 Seat LATCH Anchorages Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along gap between the seatback and seat cushion. Locating The LATCH Anchorages In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Pulling Down The Carpet Floor Panel To Access Top Tether Strap 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rear-facing infant restraints will also be equipped with a tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH — Second Row 60/40 Do not install a child restraint in the center position using the LATCH system. Use the seat belt and tether anchor to install a child seat in the center seating position. WARNING! Pulling Down The Carpet Floor Panel To Access Top Tether Strap LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some Never use the same lower anchorage to attach more than one child restraint. Please refer to “Installing The LATCH-Compatible Child Restraint System” for typical installation instructions. Always follow the directions of the child restraint manu- facturer when installing your child restraint. Not all child restraint systems will be installed as described here. Vehicles With A Center Arm Rest Tether For rearward facing infant seats secured in the center seat position with the vehicle seat belts, the rear center seat position has an armrest tether that secures the arm rest in the upward position. 1. To access the center seat arm rest tether, first lower the arm rest. The tether is located behind the armrest and hooked onto the plastic seat backing. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Center Seat Position Arm Rest Tether 2. Pull down on the tether to unhook it from the plastic seat backing. 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Raise the armrest and attach the tether hook to the strap located on the front of the arm rest. Center Seat Position Arm Rest Tether Attached To Install A LATCH-compatible Child Restraint 1. If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below. See the section “Installing Child Restraints Using the Vehicle Seat Belt” to check what type of seat belt each seating position has. 2. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 3. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recline the seat and / or raise the head restraint to get a better fit. 4. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 5. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “Installing Child Restraints Using the Top Tether Anchorage” for direc- tions to attach a tether anchor. 6. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack in the straps according to the child restraint manufac- turer’s instructions. 7. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 How To Stow An Unused ALR Seatbelt When using the LATCH attaching system to install a child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seatbelt retractor. Before installing a child restraint using the LATCH system, buckle the seat belt behind the child restraint and out of the child’s reach. If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. 100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using The Vehicle Seat Belt The seat belts in the passenger seating positions are equipped with either a Switchable Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can be “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor. For additional information on ALR, refer to the “Automatic Locking Mode” description un- der “Occupant Restraints.” The cinching latch plate is designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight through a child restraint’s belt path. Please see the table below and the following sections for more information about both types of seat belts. Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is the weight What limit (child’s weight + weight of the child re- straint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Yes Can the head restraints be removed? Yes, center position only. Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Yes Always use the tether anchor when using the seat belt to install a for- ward facing child restraint, up to the recommended weight limit of the child restraint. Contact between the front passenger seat and the child restraint is al- lowed, if the child restraint manu- facturer also allows contact. In positions with cinching latch plates (CINCH), the buckle stalk may be twisted up to 3 full turns. Do not twist the buckle stalk in a seating position with an ALR retractor. Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. 2. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. 3. Slide the latch plate into the buckle until you hear a “click.” 4. Pull on the webbing to make the lap portion tight against the child seat. 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any web- bing. If the retractor is not locked, repeat step 5. 7. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 8. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Lower Anchors and Tethers for Chil- dren (LATCH) Restraint System” for directions to attach a tether anchor. 104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. Installing A Child Restraint With A Cinching Latch Plate (CINCH) — If Equipped 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and / or raise the head restraint to get a better fit. 2. Next, pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. 3. Slide the latch plate into the buckle until you hear a “click.” 4. Finally, pull up on any excess webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 5. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. Refer to “Lower Anchors and Tethers for Chil- dren (LATCH) Restraint System” for directions to attach a tether anchor. 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Installing Child Restraints Using The Top Tether Anchorage 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position (see the charts above), move the child restraint to another position in the vehicle if one is available. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, discon- nect the latch plate from the buckle and twist the short buckle-end belt up to three full turns to shorten it. Insert the latch plate into the buckle with the release button facing out, away from the child restraint. Repeat steps 4 to 6, above, to complete the installation of the child restraint. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate into the buckle again. If you still cannot make the child restraint installation tight, try a different seating position. 106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchor- ages. Top Tether Strap Anchorage (Located on Seatback) Pulling Down The Carpet Floor Panel To Access Top Tether Strap 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 4. For the center seating position, route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Top Tether Strap Mounting 6. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. 108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The top tether anchorages are not visible until the gap panel is folded down. Do not use the visible cargo tie down hooks, located on the floor behind the seats, to attach a child restraint tether anchor. Installing Child Restraints Using The Top Tether Anchorage — Center Seating Position For center seating position route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detri- mental and should be avoided. The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “Maintenance Procedures” in “Maintaining Your Ve- hicle”. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. 110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. • If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, replace the belt. Air Bag Warning Light The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your autho- rized dealer for service if your defroster is inoperable. Floor Mat Safety Information Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. 112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfer- ing with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals. (Continued) WARNING! (Continued) • Check mounting of mats on a regular basis. Always properly reinstall and secure floor mats that have been removed for cleaning. • Always make sure that objects cannot fall into the driver footwell while the vehicle is moving. Ob- jects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. • If required, mounting posts must be properly in- stalled, if not equipped from the factory. Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately. Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure. Lights Have someone observe the operation of brake lights and exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . ..122 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . ..122 ▫ Automatic Dimming Mirror — If Equipped . . .123 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .124 ▫ Outside Mirrors Folding Feature . . . . . . . . ..124 ▫ Outside Automatic Dimming Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .124 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . ..125 ▫ Heated Mirrors — If Equipped . . . . . . . . . ..126 ▫ Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped . . . . . . . . . . . . . ..126 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . ..126 ▫ Sun Visor Extension — If Equipped . . . . . . ..127 䡵 BLIND SPOT MONITORING — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .127 ▫ Rear Cross Path . . . . . . . . . . . . . . . . . . . . . .133 ▫ Modes Of Operation . . . . . . . . . . . . . . . . . ..134 䡵 Uconnect® Phone — IF EQUIPPED . . . . . . . . ..136 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .138 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . ..145 ▫ Uconnect® Phone Features . . . . . . . . . . . . . ..148 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Advanced Phone Connectivity . . . . . . . . . . ..153 ▫ Things You Should Know About Your Uconnect® Phone . . . . . . . . . . . . . . . ..155 ▫ General Information . . . . . . . . . . . . . . . . . ..166 䡵 VOICE COMMAND — IF EQUIPPED . . . . . ..166 ▫ Voice Command System Operation . . . . . . . ..166 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . ..168 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . ..172 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..172 ▫ Power Seats — If Equipped . . . . . . . . . . . . ..173 ▫ Passenger’s Power Seat . . . . . . . . . . . . . . . ..175 ▫ Power Lumbar — If Equipped . . . . . . . . . . ..176 ▫ Manual Front Seats Forward/Rearward Adjustment . . . . . . . . . . . . . . . . . . . . . . . . .177 ▫ Manual Front Passenger Seatback Adjustment — Recline . . . . . . . . . . . . . . . ..178 ▫ Front Passenger Seat Fold-Flat Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .178 ▫ Heated Seats — If Equipped . . . . . . . . . . . . ..179 ▫ Ventilated Seats — If Equipped . . . . . . . . . . ..182 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . ..183 ▫ 60/40 Split Rear Seat . . . . . . . . . . . . . . . . ..187 ▫ Reclining Rear Seat . . . . . . . . . . . . . . . . . . ..189 䡵 DRIVER MEMORY SEAT — IF EQUIPPED . . . .189 ▫ Programming The Memory Feature . . . . . . . ..191 ▫ Linking And Unlinking The Remote Keyless Entry Transmitter To Memory . . . . . . . . . . . ..192 ▫ Memory Position Recall . . . . . . . . . . . . . . . ..193 ▫ Easy Entry/Exit Seat . . . . . . . . . . . . . . . . . ..194 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . ..195 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . ..197 ▫ Automatic Headlights — If Equipped . . . . . ..198 ▫ Headlights On Automatically With Wipers . . .198 ▫ SmartBeam™ — If Equipped . . . . . . . . . . . ..199 ▫ Daytime Running Lights — If Equipped . . . ..200 ▫ Automatic Headlight Leveling — HID Headlights Only. . . . . . . . . . . . . . . . . ..200 ▫ Headlight Delay . . . . . . . . . . . . . . . . . . . . . .200 ▫ Parking Lights And Panel Lights. . . . . . . . . ..201 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . ..201 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . ..202 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . ..203 ▫ Battery Saver. . . . . . . . . . . . . . . . . . . . . . . . .203 ▫ Front Map/Reading Lights . . . . . . . . . . . . ..203 ▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . ..259 ▫ Ambient Light. . . . . . . . . . . . . . . . . . . . . . ..205 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . ..205 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .206 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . ..206 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . ..206 ▫ High/Low Beam Switch. . . . . . . . . . . . . . . ..206 䡵 WINDSHIELD WIPERS AND WASHERS . . . . ..206 ▫ Windshield Wiper Operation . . . . . . . . . . . ..207 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Intermittent Wiper System . . . . . . . . . . . . . ..208 ▫ Windshield Washer Operation. . . . . . . . . . . ..208 ▫ Mist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..209 ▫ Rain Sensing Wipers — If Equipped . . . . . . ..210 䡵 TILT/TELESCOPING STEERING COLUMN . . .212 䡵 POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED . . . . . . . . . . . . . ..213 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .214 䡵 ELECTRONIC SPEED CONTROL . . . . . . . . . ..215 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . ..216 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . ..216 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . ..216 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . ..217 ▫ To Vary The Speed Setting . . . . . . . . . . . . . ..217 ▫ To Accelerate For Passing . . . . . . . . . . . . . . ..217 䡵 ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .218 ▫ Adaptive Cruise Control (ACC) Operation . . . .220 ▫ Activating Adaptive Cruise Control (ACC). . . .221 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . ..222 ▫ To Set A Desired ACC Speed . . . . . . . . . . . ..223 ▫ To Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . .224 ▫ To Turn Off . . . . . . . . . . . . . . . . . . . . . . . . ..225 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . ..225 ▫ To Vary The Speed Setting . . . . . . . . . . . . . ..226 ▫ Setting The Following Distance In ACC . . . . ..227 ▫ Adaptive Cruise Control (ACC) Menu . . . . . ..230 ▫ Display Warnings And Maintenance . . . . . . ..232 ▫ Precautions While Driving With ACC . . . . . ..236 ▫ General Information . . . . . . . . . . . . . . . . . ..239 ▫ Normal (Fixed Speed) Cruise Control Mode . . .239 ▫ Forward Collision Warning — If Equipped. . . .241 䡵 PARKSENSE® REAR PARK ASSIST — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .246 ▫ ParkSense® Sensors . . . . . . . . . . . . . . . . . . ..246 ▫ ParkSense® Warning Display . . . . . . . . . . . ..247 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . ..248 ▫ Enabling And Disabling ParkSense® . . . . . . ..251 ▫ Service The ParkSense® Rear Park Assist System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 ▫ Cleaning The ParkSense® System . . . . . . . . ..252 ▫ ParkSense® System Usage Precautions. . . . . ..253 䡵 PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .255 ▫ Turning ParkView® On Or Off — With Navigation/Multimedia Radio . . . . . . . . . . ..257 ▫ Turning ParkView® On Or Off — Without Navigation/Multimedia Radio . . . . . . . . . . ..257 䡵 OVERHEAD CONSOLE . . . . . . . . . . . . . . . . ..258 ▫ Front Map/Reading Lights . . . . . . . . . . . . ..258 ▫ Courtesy Lights . . . . . . . . . . . . . . . . . . . . . ..259 ▫ Sunglasses Bin Door . . . . . . . . . . . . . . . . . ..260 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .260 ▫ Before You Begin Programming HomeLink® . .262 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Programming A Rolling Code . . . . . . . . . . . ..262 ▫ Programming A Non-Rolling Code . . . . . . . ..264 ▫ Canadian/Gate Operator Programming . . . . ..266 ▫ Using HomeLink®. . . . . . . . . . . . . . . . . . . ..267 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . ..267 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . ..268 ▫ General Information. . . . . . . . . . . . . . . . . . ..269 䡵 POWER SUNROOF — IF EQUIPPED . . . . . . ..269 ▫ Opening Sunroof — Express . . . . . . . . . . . . ..270 ▫ Opening Sunroof — Manual Mode . . . . . . . ..274 ▫ Closing Sunroof — Express. . . . . . . . . . . . . ..270 ▫ Closing Sunroof — Manual Mode . . . . . . . . ..274 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . ..275 ▫ Venting Sunroof — Express . . . . . . . . . . . . ..271 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . ..271 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . ..272 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . ..272 ▫ Ignition OFF Operation . . . . . . . . . . . . . . . ..272 䡵 COMMANDVIEW® SUNROOF WITH POWER SHADE — IF EQUIPPED . . . . . . . . . . . . . . . ..272 ▫ Opening Sunroof — Express . . . . . . . . . . . . ..274 ▫ Opening Sunroof — Manual Mode . . . . . . . ..274 ▫ Closing Sunroof — Express. . . . . . . . . . . . . ..274 ▫ Closing Sunroof — Manual Mode . . . . . . . . ..274 ▫ Opening Power Shade — Express . . . . . . . . ..274 ▫ Opening Power Shade — Manual Mode . . . ..275 ▫ Closing Power Shade — Express . . . . . . . . . ..275 ▫ Closing Power Shade — Manual Mode . . . . ..275 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . ..275 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . ..276 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . ..276 ▫ Ignition OFF Operation . . . . . . . . . . . . . . . ..276 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . ..276 䡵 ELECTRICAL POWER OUTLETS . . . . . . . . . ..277 䡵 POWER INVERTER — IF EQUIPPED . . . . . . ..281 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . ..282 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . ..284 ▫ Glove Compartment . . . . . . . . . . . . . . . . . ..284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 ▫ Door Storage. . . . . . . . . . . . . . . . . . . . . . . . .285 ▫ Center Console . . . . . . . . . . . . . . . . . . . . . ..285 䡵 CARGO AREA FEATURES . . . . . . . . . . . . . . ..287 ▫ Rechargeable Flashlight . . . . . . . . . . . . . . . ..287 ▫ Cargo Storage Bins . . . . . . . . . . . . . . . . . . ..288 ▫ Retractable Cargo Area Cover — If Equipped . .290 ▫ Rear Cargo Tie-Downs . . . . . . . . . . . . . . . ..291 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . ..293 ▫ Rear Window Wiper/Washer . . . . . . . . . . . ..293 ▫ Rear Window Defroster . . . . . . . . . . . . . . . ..294 䡵 ROOF LUGGAGE RACK — IF EQUIPPED . . . ..295 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while the small control under the mirror is set in the day position (toward the windshield). Adjusting Rearview Mirror Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will illuminate to indicate when the dim- ming feature is activated. The mirror is twisted on the windshield button counterclockwise and requires no tools for mounting. NOTE: This feature is disabled when the vehicle is moving in reverse. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Some vehicles will not have a convex passenger side mirror. Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: • full forward • full rearward and • normal. Outside Automatic Dimming Mirrors — If Equipped The drivers outside mirror will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside automatic dimming mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirrors will automatically adjust for headlight glare when the inside mirror adjusts. Power Mirrors The power mirror switch is located on the driver’s side door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Power Mirror Switch 1 — Mirror Direction Control 2 — Mirror Selection Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in “Understanding The Features Of Your Vehicle” for further information. 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped. Some vehicles may not be equipped with rear window defroster, in this case the heated mirrors will still function as intended. Refer to “Rear Window Features” in “Understanding The Fea- tures Of Your Vehicle” for further information. Tilt Mirrors In Reverse (Available With Memory Seat Only) — If Equipped Tilt Mirrors in Reverse provides automatic outside mirror positioning which will aid the drivers view of the ground rearward of the front doors. Outside mirrors will move slightly downward from the present position when the vehicle is shifted into REVERSE. Outside mirrors will then return to the original position when the vehicle is shifted out of REVERSE position. Each stored memory setting will have an associated Tilt Mirrors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not enabled when delivered from the factory. The Tilt Mirrors in Reverse feature can be enabled or disabled in the Elec- tronic Vehicle Information Center (EVIC). Refer to “Elec- tronic Vehicle Information Center (EVIC)/Customer- Programmable Features” in “Understanding Your Instru- ment Panel” for further information. Illuminated Vanity Mirrors To access an illuminated vanity mirror, flip down one of the visors. Lift the cover to reveal the mirror. The light will turn on automatically. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 BLIND SPOT MONITORING — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. Illuminated Vanity Mirror Sun Visor Extension — If Equipped This feature has a pull out extension on the sun visor for increased coverage. Rear Detection Zones 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational. The BSM system sensors operate when the vehicle is in any forward gear or REVERSE and enters stand-by mode when the vehicle is in PARK. The BSM detection zone covers approximately one lane on both sides of the vehicle (11 ft or 3.35 m). The zone starts at the outside rear view mirror and extends ap- proximately 20 ft (6 m) to the rear of the vehicle. The BSM system monitors the detection zones on both sides of the vehicle when the vehicle speed has reached approxi- mately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones. • The BSM system detection zone DOES NOT change if your vehicle is towing a trailer. Therefore, visually verify the adjacent lane is clear for both your vehicle and trailer before making a lane change. If the trailer or other object (i.e., bicycle, sports equipment) extends beyond the side of your vehicle, this may result in the BSM warning light remaining illuminated the entire time the vehicle is in a forward gear. The area on the rear fascia where the radar sensors are located must remain free of snow, ice, and dirt/road contamination so that the BSM system can function properly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bum- per stickers, bicycle racks, etc.). UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Sensor Location (Driver Side Shown) Warning Light Location The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “Modes Of Operation” for further information. The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary. The BSM system will issue an alert during these types of zone entries. 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle. Entering From The Rear Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h). Side Monitoring Rear Monitoring Overtaking Traffic If you pass another vehicle slowly (with a relative speed less than 10 mph (16 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 10 mph (16 km/h), the warning light will not illuminate. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Overtaking/Passing Overtaking/Approaching 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Stationary Objects Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicles mirrors, glance over your shoulder, and use your turn signal before changing lanes. Failure to do so can result in serious injury or death. Rear Cross Path The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The RCP system will then have a clear view of the cross traffic and if an oncoming vehicle is detected, alert the driver. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 RCP Detection Zones RCP monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 to 2 mph (1 km/h to 3 km/h), to objects moving a maxi- mum of approximately 10 mph (16 km/h), such as in parking lot situations. 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume. WARNING! RCP is not a Back Up Aid system. It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be careful when backing up, even when using RCP. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before back- ing up. Failure to do so can result in serious injury or death. Modes Of Operation Three selectable modes of operation are available in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (Customer-Programmable Features)” in “Under- standing Your Instrument Panel” for further information. Blind Spot Alert When operating in Blind Spot Alert mode, the BSM system will provide a visual alert in the appropriate side view mirror based on a detected object. However, when the system is operating in RCP, the system will respond with both visual and audible alerts when a detected object is present. Whenever an audible alert is requested, the radio is muted. Blind Spot Alert Lights/Chime When operating in Blind Spot Alert Lights/Chime mode, the BSM system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, an audible chime will also be sounded. Whenever a turn signal and detected object are present on the same side at the same time, both the visual and audio alerts will be issued. In addition to the audible alert the radio (if on) will also be muted. NOTE: • Whenever an audible alert is requested by the BSM • If the hazard flashers are on, the system will request system, the radio is also muted. the appropriate visual alert only. When the system is in RCP, the system shall respond with both visual and audible alerts when a detected object is UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 present. Whenever an audible alert is requested, the radio is also muted. Turn/hazard signal status is ignored; the RCP state always requests the chime. Blind Spot Alert Off When the BSM system is turned off there will be no visual or audible alerts from either the BSM or RCP systems. NOTE: The BSM system will store the current operating mode when the vehicle is shut off. Each time the vehicle is started the previously stored mode will be recalled and used Astronomy Zone — System Temporarily Unavailable When the vehicle enters this zone the blind spot system will become temporarily unavailable and the EVIC will display the message “ Blind spot system unavailable- Astronomy zone”. The side mirrors LED’s will be lit up and stay lit until the vehicle exits the zone. 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect® Phone — IF EQUIPPED Uconnect® Phone is a voice-activated, hands-free, in- vehicle communications system. Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehicle’s audio system; the sys- tem will automatically mute your radio when using the Uconnect® Phone. NOTE: The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® “Hands-Free Profile”, Version 0.96 or higher. See the Uconnect® website for supported phones. For Uconnect® customer support, visit www.UconnectPhone.com or call 1–877–855–8400. (U.S. Residents). Canadian Residents call, 1-800-465–2001 (English) or 1-800-387-9983 (French). Uconnect® Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The Uconnect® Phone is driven through your Bluetooth® “Hands-Free Profile” mobile phone. Uconnect® features Bluetooth® technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so Uconnect® Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect® Phone. The Uconnect® Phone allows up to seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in English, Spanish, or French languages. WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. Your at- tention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death. Uconnect® Phone Button The radio or (if equipped) will contain the two control buttons button and Voice Com- (Uconnect® Phone button) that will enable you to mand steering wheel controls UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 access the system. When you press the button you will hear the word Uconnect® followed by a BEEP. The beep is your signal to give a command. Voice Command Button Actual button location may vary with the ra- dio. The individual buttons are described in the “Operation” section. The Uconnect® Phone can be used with any Hands-Free Profile certified Bluetooth® mobile phone. See the Uconnect® website for supported phones. Refer to your mobile service provider or the phone manufacturer for details. The Uconnect® Phone is fully integrated with the vehi- cle’s audio system. The volume of the Uconnect® Phone can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The radio display will be used for visual prompts from the Uconnect® Phone such as “CELL” or caller ID on certain radios. Operation Voice commands can be used to operate the Uconnect® Phone and to navigate through the Uconnect® Phone menu structure. Voice commands are required after most Uconnect® Phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the “Ready” prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying “Setup” and then “Pair a Device”, the following compound command can be said: “Pair a Bluetooth® Device”. • For each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice com- mand “Phonebook New Entry”, or you can break the compound form command into two voice commands: “Phonebook” and “New Entry”. Please remember, the Uconnect® Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you. Voice Command Tree Refer to “Voice Tree” in this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say “Help” following the beep. The Uconnect® Phone will play some of the options at any prompt if you ask for help. To activate the Uconnect® Phone, simply press the button and follow the audible prompts for directions. Uconnect® Phone sessions begin with a press of the button on the radio control head. Cancel Command At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) Uconnect® Phone To A Mobile Phone To begin using your Uconnect® Phone, you must pair your compatible Bluetooth® enabled mobile phone. To complete the pairing process, you will need to reference your mobile phone Owner’s Manual. The Uconnect® web- site may also provide detailed instructions for pairing. button to begin. “Device Pairing”. and follow the audible prompts. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 The following are general phone to Uconnect® Phone pairing instructions: • Press the • After the “Ready” prompt and the following beep, say • When prompted, after the beep, say “Pair a Device” • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process. • For identification purposes, you will be prompted to give the Uconnect® Phone a name for your mobile phone. Each mobile phone that is paired should be given a unique phone name. 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your Uconnect® Phone. However, at any given time, only one mobile phone can be in use, connected to your Uconnect® System. The priority allows the Uconnect® Phone to know which mobile phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect® Phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity” in this section). Dial By Saying A Number • Press the • After the “Ready” prompt and the following beep, say button to begin. “Dial”. want to call. • The system will prompt you to say the number you • For example, you can say “234-567-8901”. • The Uconnect® Phone will confirm the phone number and then dial. The number will appear in the display of certain radios. “Call”. button to begin. Call By Saying A Name • Press the • After the “Ready” prompt and the following beep, say • The system will prompt you to say the name of the • After the “Ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “John Doe”, where John Doe is a previ- ously stored name entry in the Uconnect® phonebook person you want to call. or downloaded phonebook. To learn how to store a name in the phonebook, refer to “Add Names to Your Uconnect® Phonebook”, in the phonebook. • The Uconnect® system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Phonebook Download – Automatic Phonebook Transfer From Mobile Phone If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. See Uconnect® website for supported phones. • To call a name from the Uconnect® Phonebook or downloaded Phonebook, follow the procedure in “Call by Saying a Name” section. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect® Phone. • Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if avail- able, the previously downloaded phonebook is avail- able for use. • Only the phonebook of the currently connected mobile • Either the mobile phone’s phonebook or the mobile phone is accessible. phone’s SIM card phonebook is downloaded. 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are trans- ferred and updated to Uconnect® Phone on the next phone connection. button to begin. Add Names To Your Uconnect® Phonebook NOTE: Adding names to the Uconnect® Phonebook is recommended when the vehicle is not in motion. • Press the • After the “Ready” prompt and the following beep, say • When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recom- mended. For example, say “Robert Smith” or “Robert” instead of “Bob”. “Phonebook New Entry”. • When prompted, enter the number designation (e.g., “Home”, “Work”, “Mobile”, or “Other”). This will allow you to store multiple numbers for each phone- book entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The Uconnect® Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, Uconnect® Phone automati- cally downloads your mobile phone’s phonebook. Edit Uconnect® Phonebook Entries button to begin. deleted or edited. when the vehicle is not in motion. NOTE: • Editing names in the phonebook is recommended • Automatic downloaded phonebook entries cannot be • Press the • After the “Ready” prompt and the following beep, say • You will then be asked for the name of the phonebook • Next, choose the number designation (home, work, • When prompted, recite the new phone number for the mobile, or other) that you wish to edit. entry that you wish to edit. “Phonebook Edit Entry”. phonebook entry that you are editing. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. “Phonebook Edit Entry” can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add “John Doe’s” work number later using the “Phonebook Edit Entry” feature. Delete Uconnect® Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the • After the “Ready” prompt and the following beep, say button to begin. “Phonebook Delete”. the 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries button while the from the list, press Uconnect® Phone is playing the desired entry and say “Delete”. • After you enter the name, the Uconnect® Phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current • Automatic downloaded phonebook entries cannot be language is deleted. deleted or edited. button to begin. “Phonebook Erase All”. Delete/Erase “All” Uconnect® Phonebook Entries • Press the • After the “Ready” prompt and the following beep, say • The Uconnect® Phone will ask you to verify that you • After confirmation, the phonebook entries will be • Note that only the phonebook in the current language • Automatic downloaded phonebook entries cannot be wish to delete all the entries from the phonebook. is deleted. deleted. deleted or edited. List All Names In The Uconnect® Phonebook • Press the • After the “Ready” prompt and the following beep, say button to begin. “Phonebook List Names”. • The Uconnect® Phone will play the names of all the phonebook entries, including the downloaded phone- book entries, if available. • To call one of the names in the list, press the but- ton during the playing of the desired name, and say “Call”. NOTE: The user can also exercise “Edit” or “Delete” operations at this point. • The Uconnect® Phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the Uconnect® Phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 accessed through the Uconnect® Phone. Check with your mobile service provider for the features that you have. Answer Or Reject An Incoming Call — No Call Currently In Progress When you receive a call on your mobile phone, the Uconnect® Phone will interrupt the vehicle audio sys- tem, if on, and will ask if you would like to answer the button to accept the call. To reject the call. Press the call, press and hold the button until you hear a single beep, indicating that the incoming call was rejected. Answer Or Reject An Incoming Call — Call Currently In Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your button to place the current mobile phone. Press the call on hold and answer the incoming call. 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Uconnect® Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it. Making A Second Call While Current Call Is In Progress To make a second call while you are currently on a call, button and say “Dial” or “Call” followed press the by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “Toggling Between Calls” in this section. To combine two calls, refer to “Conference Call” in this section. Place/Retrieve A Call From Hold To put a call on hold, press the button until you hear a single beep. This indicates that the call is on hold. To but- bring the call back from hold, press and hold the ton until you hear a single beep. Toggling Between Calls If two calls are in progress (one active and one on hold), press the button until you hear a single beep, indicat- ing that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on button until you hear a hold), press and hold the double beep indicating that the two calls have been joined into one conference call. Three-Way Calling To initiate three-way calling, press the button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress”. After the second call has established, button until you hear a double press and hold the beep, indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, momentarily press the but- ton. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the button until you hear a single beep. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 button to begin. Redial • Press the • After the “Ready” prompt and the following beep, say • The Uconnect® Phone will call the last number that “Redial”. was dialed from your mobile phone. NOTE: This may not be the last number dialed from the Uconnect® Phone. Call Continuation Call continuation is the progression of a phone call on the Uconnect® Phone after the vehicle ignition key has been switched to OFF. Call continuation functionality available on the vehicle can be any one of three types: • After the ignition key is switched to OFF, a call can continue on the Uconnect® Phone either until the call ends, or until the vehicle battery condition dictates cessa- tion of the call on the Uconnect® Phone and transfer of the call to the mobile phone. 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is cycled to OFF, a call can continue on the Uconnect® Phone for a certain dura- tion, after which the call is automatically transferred from the Uconnect® Phone to the mobile phone. • An active call is automatically transferred to the mo- bile phone after the ignition key is cycled to OFF. Uconnect® Phone Features Language Selection To change the language that the Uconnect® Phone is using: • Press the • After the “Ready” prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete the button to begin. language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every Uconnect® Phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and is usable across all languages. Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect® Phone is operational, you may reach the emergency number as follows: • Press the button to begin. • After the “Ready” prompt and the following beep, say “Emergency” and the Uconnect® Phone will instruct the paired mobile phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available mobile service and area. • If supported, this number may be programmable on button and say • The Uconnect® Phone does slightly lower your chances of successfully making a phone call as to that for the mobile phone directly. some systems. To do this, press the “Setup”, followed by “Emergency”. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! To use you Uconnect® Phone System in an emer- gency, your mobile phone must be: • turned on, • paired to the Uconnect® System, • and have network coverage. Roadside Assistance If you need roadside assistance: • Press the button to begin. • After the “Ready” prompt and the following beep, say “Roadside Assistance”. 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-528-2069 for the U.S., 1-877-213-4525 for Canada, 55-14-3454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). Please refer to the “Roadside Assistance” coverage details on the DVD in the Warranty Informa- tion Booklet and the Roadside Assistance references. • If supported, this number may be programmable on button and say some systems. To do this, press the “Setup”, followed by “Roadside Assistance”. Paging To learn how to page, refer to “Working with Automated Systems”. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect® Phone. Voice Mail Calling To learn how to access your voice mail, refer to “Working with Automated Systems”. Working With Automated Systems This method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your Uconnect® Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services re- quire immediate response selection. In some instances, that may be too quick for use of the Uconnect® Phone. When calling a number with your Uconnect® Phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you button and say, “3 7 4 6 #Send”. can press the Saying a number, or sequence of numbers, followed by “Send”, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect® phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to button and say, “Send.” The call and then press the system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The Uconnect® Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 network configurations. This is normal. NOTE:

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Jeep Grand Cherokee Owners Manual