2012 Hyundai Tucson Owners Manual

tory test wheel than the minimum required by law.

46

WARNING - Tire

temperature

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat build-up and possible sudden tire failure. This can cause loss of vehicle control and serious injury or death.

Tire terminology and definitions Air Pressure: The amount of air inside the tire pressing outward on the tire. Air pressure is expressed in pounds per square inch (psi) or kilo- pascal (kPa). Accessory Weight: This means the combined weight of optional acces- sories. Some examples of optional accessories are, automatic transaxle, power seats, and air conditioning. Aspect Ratio: The relationship of a tire's height to its width. Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Tire Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilo- pascals (kPa) before a tire has built up heat from driving. Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo. DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation motor vehicle safety standards. The DOT code includes the Tire Identification Number (TIN), an alphanumeric des- ignator which can also identify the tire manufacturer, production plant, brand and date of production. GVWR: Gross Vehicle Weight Rating GAWR FRT: Gross Axle Weight Rating for the Front Axle. GAWR RR: Gross Axle Weight Rating for the Rear axle.

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa): The metric unit for air pressure. Load Index: An assigned number ranging from 1 to 279 that corre- sponds to the load carrying capacity of a tire. Maximum Inflation Pressure: The maximum air pressure to which a cold tire may be inflated. The maxi- mum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum per- missible inflation pressure for that tire. Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150
pounds (68 kg).

Maintenance

Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a par- ticular side that faces outward when mounted on a vehicle. The outward facing sidewall bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the inner facing sidewall. Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure: Vehicle manufacturer's recommend- ed tire inflation pressure and shown on the tire placard. Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim: A metal support for a tire and upon which the tire beads are seat- ed. Sidewall: The portion of a tire between the tread and the bead.

7 47

Maintenance

Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called "wear bars," that show across the tread of a tire when only 2/32 inch of tread remains. UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire's traction, tempera- ture and treadwear. Ratings are determined by tire manufacturers using government testing proce- dures. The ratings are molded into the sidewall of the tire. Vehicle Capacity Weight: The num- ber of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo and luggage load.

Vehicle Maximum Load on the Tire: Load on an individual tire due to curb and accessory weight plus maximum occupant and cargo weight. Vehicle Normal Load on the Tire: Load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occu- pant weight and dividing by 2. Vehicle Placard: A label permanent- ly attached to a vehicle showing the original equipment tire size and rec- ommended inflation pressure.

All season tires HYUNDAI specifies all season tires on some models to provide good performance for use all year round, including snowy and icy road condi- tions. All season tires are identified by ALL SEASON and/or M+S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than all season tires and may be more appropriate in some areas.

Summer tires HYUNDAI specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rat- ing M+S (Mud and Snow) on the tire side wall. if you plan to operate your vehicle in snowy or icy conditions. HYUNDAI recommends the use of snow tires or all season tires on all four wheels.

Snow tires If you equip your car with snow tires, they should be the same size and have the same load capacity as the original tires. Snow tires should be installed on all four wheels; other- wise, poor handling may result. Snow tires should carry 4 psi (28
kPa) more air pressure than the pressure recommended for the stan- dard tires on the tire label on the dri- ver's side of the center pillar, or up to the maximum pressure shown on the tire sidewall, whichever is less.

48

Do not drive faster than 75 mph (120
km/h) when your vehicle is equipped with snow tires.

Tire chains Tire chains, if necessary, should be installed on the drive wheels as fol- lows. 2WD : Front wheels AWD : All four wheels

If a full set of chains is not available for a AWD vehicle, chains may be installed on the front wheels only.

Be sure that the chains are installed in accordance with the manufactur- er's instructions. To minimize tire and chain wear, do not continue to use tire chains when they are no longer needed.

WARNING - Snow or ice

(cid:129) When driving on roads cov- ered with snow or ice, drive at less than 20 mph (30 km/h).

(cid:129) Use the SAE “S” class or wire

chains.

(cid:129) If you hear noise caused by chains contacting the body, retighten the chain to avoid contact with the vehicle body. (cid:129) To prevent body damage, retighten the chains after driv- ing 0.3~0.6 miles (0.5~1.0 km). (cid:129) Do not use tire chains on vehicles equipped with alu- minum wheels. In unavoid- able circumstance, use a wire type chain.

(cid:129) Use wire chains less than 0.59
inches (15 mm) to prevent damage to the chain’s con- nection.

Maintenance

Radial-ply tires Radial-ply tires provide improved tread life, road hazard resistance and smoother high speed ride. The radi- al-ply tires used on this vehicle are of belted construction, and are selected to complement the ride and handling characteristics of your vehicle. Radial-ply tires have the same load carrying capacity, as bias-ply or bias belted tires of the same size, and use the same recommended inflation pressure. Mixing of radial-ply tires with bias-ply or bias belted tires is not recommended. Any combina- tions of radial-ply and bias-ply or bias belted tires when used on the same vehicle will seriously deteriorate vehicle handling. The best rule to fol- low is: Identical radial-ply tires should always be used as a set of four. Longer wearing tires can be more susceptible to irregular tread wear. It is very important to follow the tire rotation interval shown in this section to achieve the tread life potential of these tires. Cuts and punctures in radial-ply tires are repairable only in the tread area, because of sidewall flexing. Consult your tire dealer for radial-ply tire repairs.

7 49

A vehicle’s electrical system is protected from electrical overload damage by fuses. This vehicle has 3 fuse panels, one locat- ed in the driver’s side panel bolster, the other in the engine compartment. If any of your vehicle’s lights, acces- sories, or controls do not work, check the appropriate circuit fuse. If a fuse has blown, the element inside the fuse will melt. If the electrical system does not work, first check the driver’s side fuse panel. Always replace a blown fuse with one of the same rating. If the replacement fuse blows, this indi- cates an electrical problem. Avoid using the system involved and immediately consult an authorized HYUNDAI dealer. Four kinds of fuse are used:blade type, cartridge type, multi fuse and main fuse.

WARNING - Fuse replace-

ment

(cid:129) Never replace a fuse with any- thing but another fuse of the same rating.

(cid:129) A higher capacity fuse could cause damage and possibly a fire.

(cid:129) Never install a wire or aluminum foil instead of the proper fuse - even as a temporary repair. It may cause extensive wiring damage and a possible fire.

CAUTION

Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system.

Maintenance

FUSES Blade type

Normal

Blown

Cartridge type

Normal

Blown

Multi fuse

Normal

Blown

Main fuse

Normal

Blown

OLM079051N

50

OLM079020

Instrument panel fuse replace- ment 1. Turn the ignition switch and all other

switches off.

2. Open the fuse panel cover.

OLM079021N 3. Pull the suspected fuse straight out. Use the removal tool provided in the fuse panel.

4. Check the removed fuse; replace it if it

is blown. Spare fuses are provided in the instru- ment panel fuse panel (or in the engine compartment fuse panel).

5. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer. If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the cigarette lighter fuse.

Maintenance

If the headlights or other electrical com- ponents do not work and the fuses are OK, check the fuse panel in the engine compartment. If a fuse is blown, it must be replaced.

7 51

✽✽ NOTICE • If the memory fuse is pulled up from the fuse panel, the warning chime, audio, clock and interior lamps, etc., will not operate. Some items must be reset after replacement. Refer to “Battery” in this section.

• Even when the memory fuse is pulled up, the battery can still be discharged by operation of the headlights or other electrical devices.

Maintenance

OLM079022

Memory fuse Your vehicle is equipped with a memory fuse to prevent battery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. 1. Turn off the engine. 2. Turn off the headlights and tail lights. 3. Open the driver’s side panel cover and

pull up the memory fuse.

52

OLM079023N

Engine compartment fuse replacement 1. Turn the ignition switch and all other

switches off.

2. Remove the fuse panel cover by pressing the tab and pulling the cover up.

3. Check the removed fuse; replace it if it is blown. To remove or insert the fuse, use the fuse puller in the engine com- partment fuse panel.

4. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If it fits loosely, consult an authorized HYUNDAI dealer.

CAUTION

After checking the fuse panel in the engine compartment, securely install the fuse panel cover. If not, electrical failures may occur from water contact.

Maintenance

✽✽ NOTICE If the main fuse is blown, consult an authorized HYUNDAI dealer.

OLM079052N

Main fuse and Multi fuse If the main fuse and Multi fuse is blown, it must be removed as follows: 1. Disconnect the negative battery cable. 2. Remove the nuts shown in the picture

above.

3. Replace the fuse with a new one of the

same rating.

4. Reinstall in the reverse order of

removal.

7 53

Maintenance

Fuse/relay panel description Inside the fuse/relay panel covers, you can find the fuse/relay label describing fuse/relay name and capacity.

Instrument panel fuse panel

Engine compartment fuse panel

✽✽ NOTICE Not all fuse panel descriptions in this manual may be applicable to your vehi- cle. It is accurate at the time of printing. When you inspect the fuse panel in your vehicle, refer to the fuse panel label.

54

OLM079026/OLM079027N/OLM079053N

Maintenance

Instrument panel fuse panel

Description

Fuse rating

Protected component

AUDIO 1

ROOM LP (MEMORY FUSE)

MODULE 2
START A/BAG IND CLUSTER MODULE 4
POWER OUTLET 2
AUDIO 2
A/BAG

MODULE 1

FOG LP RR WIPER FRT S/HEATER FRT POWER OUTLET 1

10A

10A

10A 10A 10A 10A 10A 25A 10A 10A

10A

10A 25A 15A 15A

Audio, A/V & Navigation Head Module

BCM, Auto Light & Photo Sensor, Room Lamp, Driver/Passenger Vanity Lamp Switch, Date Link Connector, Door warning Switch, RF Receiver, A/C Control Module, Luggage Lamp, IPS Control Module, Instrument Cluster (IND.), Map Lamp, Electro Chromic Mirror

IPS Control Module, BCM, Electro Chromic Mirror, PDM Burglar Alarm Relay, E/R Fuse & Relay Box(Start Relay) Instrument Cluster (Air Bag IND.) Audio, Console Switch, Instrument Cluster(IND.), BCM, Alternator, A/V & Navigation Head Module E/R Fuse & Relay Box(Blower Relay), Cluster Ionizer, A/C Control Module, Sunroof Motor Cigarette Lighter & Front Power Outlet, Rear Power Outlet Power Outside Mirror Switch, AMP, BCM, PDM, A/V & Navigation Head Module, Audio SRS Control Module, Passenger Occupant Detection Sensor

IPS Control Module, Tire Pressure Monitoring Module, EPS Control Module, Steering Angle Sensor, ESC OFF Switch, DBC Switch, ICM Relay Box(DBC Relay), Multifunction Switch(Light), Stop Lamp Switch, AWD ECM

Front Wiper Motor, Multifunction Switch(Wiper), E/R Fuse & Relay Box(Front Wiper Relay) Console Switch Cigarette Lighter & Front Power Outlet

7 55

Maintenance

Description

Fuse rating

Protected component

B/UP LP DR LOCK MODULE 5
WIPER RR SUNROOF IGN 1
A/CON S/HEATER RR P/WDW RH MODULE 3
P/SEAT (DRV) PDM P/WDW LH AMP HTD MIRR SAFETY POWER WINDOW TPMS HAZARD

10A 15A 7.5A 15A 15A 20A 7.5A 15A 25A 10A 20A 15A 25A 25A 7.5A 20A 7.5A 15A

B/UP LP Relay Door Lock Relay, Tail Gate Relay, Door Unlock Relay BCM, PDM ICM Relay Box (Rear Wiper Relay), Rear Wiper Motor, Multifunction Switch (Wiper) Sunroof Motor E/R Fuse & Relay Box(ECU 2 7.5A, ABS 7.5A, TCU 2 7.5A) A/C Control Module Power Window Main Switch, Passenger Power Window Switch, Rear Power Window Switch RH Driver Seat Manual Switch PDM Power Window Main Switch, Rear Power Window Switch LH AMP Rear Defogger Switch, Rear Defogger (+), Driver/Passenger Power Outside Mirror Driver Safety Power Window Module ATM Shift Lever, AWD ECM, Tire Pressure Monitoring Module ICM Relay Box(Flasher Sound Relay), BCM

56

Maintenance

Engine compartment main fuse panel

Description

Fuse rating

MULTI FUSE

FUSE

MDPS B+1
ABS 2
EMS ABS 1
BLOWER

B+3

B+2
C/FAN RR HTD IGN 1
IGN 2
HORN DEICER STOP LP B+ SENSOR TCU 2
ABS ECU 2
F/PUMP

80A 60A 40A 40A 40A 40A

60A

60A 40A 40A 40A 40A 15A 15A 10A 10A 7.5A 7.5A 7.5A 15A

Protected component

EPS Control Module I/P Junction Box(PDM 15A, DR LOCK 15A, HAZARD 15A, IPS 4, IPS 5, IPS 6, IPS 7) Multipurpose Check Connector, ESC Control Module EMS Box(TCU 1 15A, ECU 30A, A/CON 10A, F/PUMP 15A) Multipurpose Check Connector, ESC Control Module Blower Relay I/P Junction Box(P/SEAT(DRV) 20A, SAFETY POWER WINDOW 20A, TPMS 7.5A, Power Connector(AUDIO 1 10A, ROOM LP 10A)) I/P Junction Box(Power Window Relay, SUNROOF 15A, AMP 25A, IPS 0, IPS 1, IPS 2, IPS 3) E/R Fuse & Relay Box(C/FAN LO Relay, C/FAN HI Relay) E/R Fuse & Relay Box(RR HTD Relay) PDM Relay Box(IGN1 Relay), Ignition Switch E/R Fuse & Relay Box(Statr Relay), PDM Relay Box(IGN2 Relay), Ignition Switch E/R Fuse & Relay Box(Horn Relay, B/A Horn Relay) E/R Fuse & Relay Box(Deicer Relay, RR HTD Relay) Stop Lamp Switch, ICM Relay Box(DBC Relay) Batter Sensor Transaxle Range Switch(A/T), Vehicle Speed Sensor(M/T) Multipurpose Check Connector, ESC Control Module E/R Fuse & Relay Box(ATM P/N Relay), Mass Air Flow Sensor, PCM EMS Box(F/PUMP Relay)

7 57

Maintenance

Description

Fuse rating

Protected component

FUSE

SENSOR 4

SENSOR 3
SENSOR 2
TCU 1
A/CON

SENSOR 1

ECU 1
ECU

15A

10A 10A 15A 10A

10A

20A 30A

E/R Fuse & Relay Box(C/FAN HI, LO Relay), EMS Box(F/PUMP Relay), Oxygen Sensor (UP, DOWN), PCM EMS Box(A/CON Relay), Injector(#1, #2, #3, #4) PCM EMS Box(A/CON Relay) Crankshaft Position Sensor, Camshaft Position Sensor #1/2, Oil Control Valve #1/2, Canister Purge Control Solenoid Valve, Variable Intake Manifold Valve, Canister Close Valve Ignition Colil (#1, #2, #3, #4), Condenser EMS Box(Engine Control Relay)

58

LIGHT BULBS

WARNING - Working on

the lights

Prior to working on the light, firmly apply the parking brake, ensure that the ignition switch is turned to the LOCK position and turn off the lights to avoid sudden movement of the vehicle and burning your fin- gers or receiving an electric shock.

Use only the bulbs of the specified wattage.

CAUTION

Be sure to replace the burned-out bulb with one of the same wattage rating. Otherwise, it may cause damage to the fuse or electric wiring system.

CAUTION

If you don’t have necessary tools, the correct bulbs and the expertise, consult an authorized HYUNDAI dealer.In many cases,it is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true if you have to remove the head- light assembly to get to the bulb(s). Removing/installing the headlight assembly can result in damage to the vehicle.

✽✽ NOTICE After heavy, driving rain or washing, headlight and taillight lenses could appear frosty. This condition is caused by the temperature difference between the lamp inside and outside. This is similar to the condensation on your windows inside your vehicle during the rain and doesn’t indicate a problem with your vehicle. If the water leaks into the lamp bulb circuitry, have the vehicle checked by an authorized HYUNDAI dealer.

Maintenance

OLM079029
Headlight, position light, turn sig- nal light, side marker light and front fog light bulb replacement (1) Front turn signal light (2) Position light (3) Headlight (High/Low) (4) Front side marker light (5) Front fog light (if equipped)

7 59

(Continued) (cid:129) A bulb should be operated only

when installed in a headlight.

(cid:129) If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.

(cid:129) Wear eye protection when chang- ing a bulb. Allow the bulb to cool down before handling it.

OLM079030

1. Open the hood. 2. Remove the headlight bulb cover by

turning it counterclockwise.

3. Disconnect the headlight bulb socket-

connector.

4. Unsnap the headlight bulb retaining wire by depressing the end and push- ing it upward.

Maintenance

Headlight bulb

OHD076046

WARNING - Halogen bulbs (cid:129) Halogen bulbs contain pressur- ized gas that will produce flying pieces of glass if broken.

(cid:129) Always handle them carefully, and avoid scratches and abra- sions. If the bulbs are lit, avoid contact with liquids.

(cid:129) Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.

(Continued)

60

Maintenance

3. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

4. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

5. Remove the bulb from the headlight

assembly.

6. Install a new headlight bulb and snap the headlight bulb retaining wire into position by aligning the wire with the groove on the bulb.

7. Connect the headlight bulb socket-

connector.

8. Install the headlight bulb cover by turn-

ing it clockwise.

Front fog light bulbs (if equipped) If the light bulb is not operating, have the vehicle checked by an authorized HYUNDAI dealer.

OLM079046

Turn signal light/Position light 1. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

2. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket

7 61

Maintenance

OLM079031

OLM079033

Side repeater light replacement If the light bulb does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Rear combination light bulb replacement (1) Stop and tail light (2) Rear turn signal light (3) Back-up light (4) Tail light (5) Rear side marker light

OLM079034

OLM079035

Outside light 1. Open the tailgate. 2. Loosen the light assembly retaining screws with a philips head screwdriver. 3. Remove the rear combination light assembly from the body of the vehicle.

62

Maintenance

OLM079047

Inside light 1. Open the tailgate. 2. Remove the service cover using a flat-

blade screwdriver.

OLM079036
4. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

5. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

6. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

7. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

8. Reinstall the light assembly to the

body of the vehicle.

OLM079038
3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4. Remove the bulb from the socket by pressing it in and rotating it counter- clockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

5. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

6. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

7. Install the service cover by putting it

into the service hole.

7 63

Maintenance

(A)

(B)

OLM079039

OLM071061L 4.Loosen the retaining nuts and remove

the spoiler.

5.Remove the high mounted stop light assembly (A) after loosening the nuts and washer nozzle (B).

6.Reinstall a new light assembly in the

reverse order of removal.

OLM079055

License plate light bulb replace- ment 1. Remove the lens by pressing the tabs. 2. Remove the socket from the lens. 3. Remove the bulb by pulling it straight

out.

4. Install a new bulb in the socket and

install the socket to the lens.

5. Reinstall the lens securely.

OLM071060L

High mounted stop light replacement 1.Open the tailgate. 2.Gently remove the center cover of the

rear tailgate trim.

3.Disconnect the electrical connector.

64

Map lamp

Luggage room lamp (if equipped)

Sunvisor lamp

Glove box lamp (if equipped)

Maintenance

Interior light bulb replacement 1. Using a flat-blade screwdriver, gently pry the lens from the interior light housing.

2. Remove the bulb by pulling it straight

out.

WARNING

Prior to working on the Interior Lights, ensure that the “OFF” but- ton is depressed to avoid burning your fingers or receiving an electric shock.

3. Install a new bulb in the socket. 4. Align the lens tabs with the interior light housing notches and snap the lens into place.

Room lamp

OLM079040/OXM079041/OLM079042/ OLM079044/OLM079045

Use care not to dirty or damage lens,lens tab,and plastic housings.

CAUTION

7 65

WARNING - Wet brakes

After washing the vehicle, test the brakes while driving slowly to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow for- ward speed.

Even prompt washing with plain water may not completely remove all these deposits. A mild soap, safe for use on painted surfaces, may be used. After washing, rinse the vehicle thor- oughly with lukewarm or cold water. Do not allow soap to dry on the finish.

CAUTION

(cid:129) Do not use strong soap,chemical detergents or hot water, and do not wash the vehicle in direct sunlight or when the body of the vehicle is warm.

(cid:129) Be careful when washing the side

windows of your vehicle. Especially, with high-pressure water.Water may leak through the windows and wet the interior.

(cid:129) To prevent damage to the plastic parts and lamps, do not clean with chemical solvents or strong detergents.

Maintenance

APPEARANCE CARE Exterior care Exterior general caution It is very important to follow the label directions when using any chemical cleaner or polish. Read all warning and caution statements that appear on the label.

Finish maintenance Washing To help protect your vehicle’s finish from rust and deterioration, wash it thoroughly and frequently at least once a month with lukewarm or cold water. If you use your vehicle for off-road driv- ing, you should wash it after each off- road trip. Pay special attention to the removal of any accumulation of salt, dirt, mud, and other foreign materials. Make sure the drain holes in the lower edges of the doors and rocker panels are kept clear and clean. Insects, tar, tree sap, bird droppings, industrial pollution and similar deposits can damage your vehicle’s finish if not removed immediately.

66

Waxing A good coat of wax is a barrier between your paint and contaminate. Keeping a good coat of wax on your vehicle will help protect it. Wax the vehicle when water will no longer bead on the paint. Always wash and dry the vehicle before waxing. Use a good quality liquid or paste wax, and follow the manufacturer’s instructions. Wax all metal trim to protect it and to maintain its luster. Removing oil, tar, and similar materials with a spot remover will usually strip the wax from the finish. Be sure to re-wax these areas even if the rest of the vehicle does not yet need waxing.

CAUTION

(cid:129) Wiping dust or dirt off the body with a dry cloth will scratch the finish.

(cid:129) Do not use steel wool, abrasive cleaners, or strong detergents containing highly alkaline or caustic agents on chrome-plated or anodized aluminum parts.This may result in damage to the pro- tective coating and cause discol- oration or paint deterioration.

OJB037800

CAUTION

(cid:129) Water washing in the engine com- partment including high pressure water washing may cause the fail- ure of electrical circuits located in the engine compartment.

(cid:129) Never allow water or other liquids to come in contact with electri- cal/electronic components inside the vehicle as this may damage them.

Maintenance

Finish damage repair Deep scratches or stone chips in the painted surface must be repaired promptly. Exposed metal will quickly rust and may develop into a major repair expense.

✽✽ NOTICE If your vehicle is damaged and requires any metal repair or replacement, be sure the body shop applies anti-corrosion materials to the parts repaired or replaced.

7 67

Maintenance

Bright-metal maintenance (cid:129) To remove road tar and insects, use a tar remover, not a scraper or other sharp object.

(cid:129) To protect the surfaces of bright-metal parts from corrosion, apply a coating of wax or chrome preservative and rub to a high luster.

(cid:129) During winter weather or in coastal areas, cover the bright metal parts with a heavier coating of wax or preserva- tive. If necessary, coat the parts with non-corrosive petroleum jelly or other protective compound.

68

Aluminum wheel maintenance The aluminum wheels are coated with a clear protective finish. (cid:129) Do not use any abrasive cleaner, pol- ishing compound, solvent, or wire brushes on aluminum wheels. They may scratch or damage the finish.

(cid:129) Use only a mild soap or neutral deter- gent, and rinse thoroughly with water. Also, be sure to clean the wheels after driving on salted roads. This helps pre- vent corrosion.

(cid:129) Avoid washing the wheels with high-

speed car wash brushes.

(cid:129) Do not use any cleaners containing acid or acid detergents. It may damage and corrode the aluminum wheels coated with a clear protective finish.

Underbody maintenance Corrosive materials used for ice and snow removal and dust control may col- lect on the underbody. If these materials are not removed, accelerated rusting can occur on underbody parts such as the fuel lines, frame, floor pan and exhaust system, even though they have been treated with rust protection. Thoroughly flush the vehicle underbody and wheel openings with lukewarm or cold water once a month, after off-road driving and at the end of each winter. Pay special attention to these areas because it is difficult to see all the mud and dirt. It will do more harm than good to wet down the road grime without removing it. The lower edges of doors, rocker panels, and frame members have drain holes that should not be allowed to clog with dirt; trapped water in these areas can cause rusting.

WARNING

After washing the vehicle, test the brakes while driving slowly to see if they have been affected by water. If braking performance is impaired, dry the brakes by applying them lightly while maintaining a slow for- ward speed.

High-corrosion areas If you live in an area where your vehicle is regularly exposed to corrosive materi- als, corrosion protection is particularly important. Some of the common causes of accelerated corrosion are road salts, dust control chemicals, ocean air and industrial pollution.

Corrosion protection Protecting your vehicle from corrosion By using the most advanced design and construction practices to combat corro- sion, we produces cars of the highest quality. However, this is only part of the job. To achieve the long-term corrosion resistance your vehicle can deliver, the owner's cooperation and assistance is also required.

Common causes of corrosion The most common causes of corrosion on your car are: (cid:129) Road salt, dirt and moisture that is allowed to accumulate underneath the vehicle.

(cid:129) Removal of paint or protective coatings by stones, gravel, abrasion or minor scrapes and dents which leave unpro- tected metal exposed to corrosion.

Maintenance

Moisture breeds corrosion Moisture creates the conditions in which corrosion is most likely to occur. For example, corrosion is accelerated by high humidity, particularly when tempera- tures are just above freezing. In such conditions, the corrosive material is kept in contact with the car surfaces by mois- ture that is slow to evaporate. Mud is particularly corrosive because it is slow to dry and holds moisture in contact with the vehicle. Although the mud appears to be dry, it can still retain the moisture and promote corrosion. High temperatures can also accelerate corrosion of parts that are not properly ventilated so the moisture can be dis- persed. For all these reasons, it is par- ticularly important to keep your vehicle clean and free of mud or accumulations of other materials. This applies not only to the visible surfaces but particularly to the underside of the vehicle.

7 69

Maintenance

To help prevent corrosion You can help prevent corrosion from get- ting started by observing the following:

Keep your car clean The best way to prevent corrosion is to keep your vehicle clean and free of cor- rosive materials. Attention to the under- side of the vehicle is particularly impor- tant.

(cid:129) If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your vehicle at least once a month and be sure to clean the underside thoroughly when winter is over.

70

(cid:129) When cleaning underneath the vehicle, give particular attention to the compo- nents under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accu- mulated mud rather than washing it away will accelerate corrosion rather than prevent it. Water under high pres- sure and steam are particularly effec- tive in removing accumulated mud and corrosive materials.

(cid:129) When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to accelerate corrosion.

Keep your garage dry Don't park your car in a damp, poorly ventilated garage. This creates a favor- able environment for corrosion. This is particularly true if you wash your vehicle in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contribute to corrosion unless it is well ventilated so moisture is dispersed.

Keep paint and trim in good condition Scratches or chips in the finish should be covered with "touch-up" paint as soon as possible to reduce the possibility of cor- rosion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.

Bird droppings : Bird droppings are high- ly corrosive and may damage painted surfaces in just a few hours. Always remove bird droppings as soon as possi- ble.

Don't neglect the interior Moisture can collect under the floor mats and carpeting to cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, cleaning materials or chemicals in the vehicle. These should be carried only in proper containers and any spills or leaks should be cleaned up, flushed with clean water and thoroughly dried.

Interior care Interior general precautions Prevent caustic solutions such as per- fume and cosmetic oil from contacting the dashboard because they may cause damage or discoloration. If they do con- tact the dashboard, wipe them off imme- diately. See the instructions for the prop- er way to clean vinyl.

CAUTION

Never allow water or other liquids to come in contact with electrical/elec- tronic components inside the vehi- cle as this may damage them.

CAUTION

When cleaning leather products (steering wheel, seats etc.), use neutral detergents or low alcohol content solutions. If you use high alcohol content solutions or acid/alkaline detergents, the color of the leather may fade or the sur- face may get stripped off.

Cleaning the upholstery and interior trim Vinyl Remove dust and loose dirt from vinyl with a whisk broom or vacuum cleaner. Clean vinyl surfaces with a vinyl cleaner.

Fabric Remove dust and loose dirt from fabric with a whisk broom or vacuum cleaner. Clean with a mild soap solution recom- mended for upholstery or carpets. Remove fresh spots immediately with a fabric spot cleaner. If fresh spots do not receive immediate attention, the fabric can be stained and its color can be affected. Also, its fire-resistant properties can be reduced if the material is not properly maintained.

CAUTION

Using anything but recommended cleaners and procedures may affect the fabric’s appearance and fire- resistant properties.

Maintenance

Cleaning the lap/shoulder belt web- bing Clean the belt webbing with any mild soap solution recommended for cleaning upholstery or carpet. Follow the instruc- tions provided with the soap. Do not bleach or re-dye the webbing because this may weaken it.

Cleaning the interior window glass If the interior glass surfaces of the vehi- cle become fogged (that is, covered with an oily, greasy or waxy film), they should be cleaned with glass cleaner. Follow the directions on the glass cleaner container.

CAUTION

Do not scrape or scratch the inside of the rear window.This may result in damage to the rear window defroster grid.

7 71

Maintenance

EMISSION CONTROL SYSTEM The emission control system of your vehicle is covered by a written limited warranty. Please see the warranty infor- mation contained the Owner’s Handbook & Warranty Information book- let in your vehicle. Your vehicle is equipped with an emis- sion control system to meet all applicable emission regulations. There are three emission control sys- tems, as follows.

in

(1) Crankcase emission control system (2) Evaporative emission control system (3) Exhaust emission control system

In order to assure the proper function of the emission control systems, it is rec- ommended that you have your vehicle inspected and maintained by an author- ized HYUNDAI dealer in accordance with the maintenance schedule in this manu- al.

72

for

the

Caution Inspection and Maintenance Test (With Electronic Stability Control (ESC) system) (cid:129) To prevent the vehicle from misfir- ing during dynamometer testing, turn the Electronic Stability Control (ESC) system off by pressing the ESC switch.

(cid:129) After dynamometer testing is com- pleted, turn the ESC system back on by pressing the ESC switch again.

1. Crankcase emission control

system

The positive crankcase ventilation sys- tem is employed to prevent air pollution caused by blow-by gases being emitted from the crankcase. This system supplies fresh filtered air to the crankcase through the air intake hose. Inside the crankcase, the fresh air mixes with blow-by gases, which then pass through the PCV valve into the induction system.

2. Evaporative emission control

(including ORVR: Onboard Refueling Vapor Recovery) system

The Evaporative Emission Control System is designed to prevent fuel vapors from escaping into the atmos- phere. (The ORVR system is designed to allow the vapors from the fuel tank to be loaded into a canister while refueling at the gas station, preventing the escape of fuel vapors into the atmosphere.)

Canister Fuel vapors generated inside the fuel tank are absorbed and stored in the onboard canister. When the engine is running, the fuel vapors absorbed in the canister are drawn into the surge tank through the purge control solenoid valve.

Purge Control Solenoid Valve (PCSV) The purge control solenoid valve is con- trolled by the Engine Control Module (ECM); when the engine coolant temper- ature is low during idling, the PCSV clos- es so that evaporated fuel is not taken into the engine. After the engine warms- up during ordinary driving, the PCSV opens to introduce evaporated fuel to the engine.

3. Exhaust emission control

system

The Exhaust Emission Control System is a highly effective system which controls exhaust emissions while maintaining good vehicle performance.

Vehicle modifications This vehicle should not be modified. Modification of your vehicle could affect its performance, safety or durability and may even violate governmental safety and emissions regulations. In addition, damage or performance problems resulting from any modification may not be covered under warranty. (cid:129) If you use unauthorized electronic devices, it may cause the vehicle to operate abnormally, wire damage, bat- tery discharge and fire. For your safety, be careful not to damage.

Engine exhaust gas precautions (carbon monoxide) (cid:129) Carbon monoxide can be present with other exhaust fumes. Therefore, if you smell exhaust fumes of any kind inside your vehicle, have it inspected and repaired immediately. If you ever sus- pect exhaust fumes are coming into your vehicle, drive it only with all the windows fully open. Have your vehicle checked and repaired immediately.

Maintenance

WARNING - Exhaust

Engine exhaust gases contain car- bon monoxide (CO). Though color- less and odorless, it is dangerous and could be lethal if inhaled. Follow the instructions on this page to avoid CO poisoning.

CALIFORNIA PROPOSI- TION 65 WARNING

Engine exhaust and a wide variety of automobile components and parts, including components found in the interior furnishings in a vehi- cle, contain or emit chemicals known to the State of California to cause cancer and birth defects and reproductive harm. In addition, cer- tain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

7 73

Maintenance

(cid:129) Do not operate the engine in confined or closed areas (such as garages) any more than what is necessary to move the vehicle in or out of the area.

(cid:129) When the vehicle is stopped in an open area for more than a short time with the engine running, adjust the ventilation system (as needed) to draw outside air into the vehicle.

(cid:129) Never sit in a parked or stopped vehi- cle for any extended time with the engine running.

(cid:129) When the engine stalls or fails to start, excessive attempts to restart the engine may cause damage to the emission control system.

74

Operating precautions for catalytic converters (if equipped)

WARNING - Fire

(cid:129) A hot exhaust system can ignite flammable items under your vehi- cle. Do not park, idle, or drive the vehicle over or near flammable objects, such as grass, vegeta- tion, paper, leaves, etc.

(cid:129) The exhaust system and catalytic system are very hot while the engine is running or immediately after the engine is turned off. Keep away from the exhaust system and catalytic, you may get burned. Also, do not remove the heat sink around the exhaust system, do not seal the bottom of the vehicle or do not coat the vehicle for cor- rosion control. It may present a fire risk under certain conditions.

Your vehicle is equipped with a catalytic converter emission control device. Therefore, the following precautions must be observed: (cid:129) Use only UNLEADED FUEL for gaso-

line engines.

(cid:129) Do not operate the vehicle when there are signs of engine malfunction, such as misfire or a noticeable loss of per- formance.

(cid:129) Do not misuse or abuse the engine. Examples of misuse are coasting with the ignition off and descending steep grades in gear with the ignition off.

(cid:129) Do not operate the engine at high idle speed for extended periods (5 minutes or more).

(cid:129) Do not modify or tamper with any part of the engine or emission control sys- tem. All inspections and adjustments must be made by an authorized HYUNDAI dealer.

(cid:129) Avoid driving with a extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.

Failure to observe these precautions could result in damage to the catalytic converter vehicle. Additionally, such actions could void your warranties.

your

and

to

CALIFORNIA PERCHLORATE NOTICE Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/haz- ardouswaste/perchlorate.

Notice to California Vehicle Dismantlers: Perchlorate containing materials, such as air bag inflators, seatbelt pretensioners and keyless remote entry batteries, must be disposed of according to Title 22
California Code of Regulations Section 67384.10 (a).

Maintenance

7 75

Dimensions / 8-2
Bulb wattage / 8-2
Tires and wheels / 8-3
Recommended lubricants and capacities / 8-4
Vehicle identification number (VIN) / 8-6
Vehicle certification label / 8-6
Tire specification and pressure label / 8-7
Engine number / 8-7
Consumer information / 8-8
Reporting safety defects / 8-9
Binding arbitration / 8-9

Specifications, Consumer information, Reporting safety defects

Specifications, Consumer information, Reporting safety defects

DIMENSIONS

Item

Overall length Overall width Overall height Front tread Rear tread Wheelbase

*1 : with roof rack

in (mm)

173.2 (4400) 71.7 (1820)

65.2 (1655) / 66.3 (1685)*1

62.4 (1585) 62.44 (1586) 103.9 (2640)

BULB WATTAGE

Light Bulb

Headlights (High/Low) Front turn signal lights Position lights Side repeater lights Front side marker lights Front fog lights* Stop and tail lights Rear turn signal lights Back-up lights Rear side marker lights* High mounted stop light License plate lights Map lamps Room lamps Luggage lamp* Glove box lamp Vanity mirror lamps

* : if equipped

Wattage

60/55
28/8

LED

27
28/8
27
16

LED

10
10

28

Specifications, Consumer information, Reporting safety defects

TIRES AND WHEELS

Item

Tire size

Wheel size

Inflation pressure

kPa (psi)

Wheel lug nut torque

lb•ft (kgf(cid:129)m, N(cid:129)m)

Full size tire

225/60R17
225/55R18

6.5J×17
6.5J×18

Compact spare tire

T155/90D16

4.0T×16

Front 230
(33)

420
(60)

Rear 230
(33)

420
(60)

65~79

(9~11 , 88~107)

✽✽ NOTICE It is permissible to add 3psi to the standard tire pressure specification if colder temperatures are expected soon. Tires typically loose 1psi for every 12°F temperature drop. If extreme temperature variations are expected, re-check your tire pressure as nec- essary to keep them properly inflated.

8 3

Specifications, Consumer information, Reporting safety defects

RECOMMENDED LUBRICANTS AND CAPACITIES To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality. The correct lubricants also help promote engine efficiency that results in improved fuel economy. These lubricants and fluids are recommended for use in your vehicle.

Lubricant

Volume

Classification

Engine oil *1 *2 (drain and refill) Recommends

2.0 Engine

4.33 US qt. (4.1 l)

Manual transaxle fluid

2.4 Engine

4.86 US qt. (4.6 l)

2.0 Engine

2.4 Engine

2.22~2.32 US qt.

(2.1~2.2 l)

1.90~2.01 US qt.

(1.8~1.9 l)

Automatic transaxle fluid

7.50 US qt. (7.1 l)

Coolant

7.19 US qt. (6.8 l)

API Service SM*3,

ILSAC GF-4 or above

API GL-4, SAE 75W/85

MICHANG ATF SP-IV, SK ATF SP-IV

NOCA ATF SP-IV, HYUNDAI genuine ATF SP-IV or other

brands meeting the above specification approved by

Hyundai Motor Co.,

Mixture of antifreeze and water (Ethylene glycol base

coolant for aluminum radiator) FMVSS116 DOT-3 or DOT-4

0.7~0.8 US qt. (0.7~0.8 l)

Brake/clutch fluid Rear axle oil (AWD) Transfer case oil (AWD) Fuel *1 Refer to the recommended SAE viscosity numbers on the next page. *2 Engine oils labeled Energy Conserving Oil are now available. Along with other additional benefits, they contribute to fuel economy by reducing the amount of fuel necessary to overcome engine friction. Often, these improvements are difficult to measure in everyday driving, but in a year’s time, they can offer significant cost and energy savings.

0.69 US qt. (0.65 l) 0.63 US qt. (0.6 l) 15.3 US gal. (58 l)

Hypoid gear oil API GL-5, SAE 75W/90

(SHELL SPIRAX X or equivalent)

*3 If the API service SM engine oil is not available in your country, you are able to use API service SL.

48

Recommended SAE viscosity number

CAUTION

Always be sure to clean the area around any filler plug,drain plug,or dipstick before checking or drain- ing any lubricant.This is especially important in dusty or sandy areas and when the vehicle is used on unpaved roads. Cleaning the plug and dipstick areas will prevent dirt and grit from entering the engine and other mechanisms that could be damaged.

Specifications, Consumer information, Reporting safety defects

Engine oil viscosity (thickness) has an effect on fuel economy and cold weather operating (engine start and engine oil flowability). Lower viscosity engine oils can provide better fuel economy and cold weather performance, however, higher viscosity engine oils are required for sat- isfactory lubrication in hot weather. Using oils of any viscosity other than those rec- ommended could result in engine dam- age.

When choosing an oil, consider the range of temperature your vehicle will be oper- ated in before the next oil change. Proceed to select the recommended oil viscosity from the chart.

Temperature

Gasoline Engine Oil *1

Temperature Range for SAE Viscosity Numbers °C (°F)

-30 -20 -10 0 10 20 30 40 50
-10 0 20 40 60 80 100 120

10W-30

5W-20, 5W-30

*1 For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE 5W-20 (API SM / ILSAC GF-4). However, if the engine oil is not available in your country, select the proper engine oil using the engine oil viscosity chart.

8 5

Specifications, Consumer information, Reporting safety defects

VEHICLE IDENTIFICATION NUMBER (VIN) Frame number

VIN label

VEHICLE CERTIFICATION LABEL

OLM089001

The vehicle identification number (VIN) is the number used in registering your car and in all legal matters pertaining to its ownership, etc. The number is punched on the floor under the passenger seat. To check the number, open the cover.

OLM089006N The VIN is also on a plate attached to the top of the dashboard. The number on the plate can easily be seen through the windshield from outside.

OLM089002N The vehicle certification label attached on the driver’s side center pillar gives the vehicle identification number (VIN).

68

TIRE SPECIFICATION AND PRESSURE LABEL

ENGINE NUMBER

Specifications, Consumer information, Reporting safety defects

OLM089003
The engine number is stamped on the engine block as shown in the drawing.

OLM089008N

The tires supplied on your new vehicle are chosen to provide the best perform- ance for normal driving. The tire label located on the driver's side center pillar gives the tire pressures rec- ommended for your car.

8 7

Specifications, Consumer information, Reporting safety defects

CONSUMER INFORMATION This consumer information has been pre- pared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. Your Hyundai dealer will help answer any questions you may have as you read this information.

Hyundai motor vehicles are designed and manufactured to meet or exceed all applicable safety standards.

For your safety, however, we strongly urge you to read and follow all directions in this Owner's Manual, particularly the information headings "NOTICE", "CAUTION" and "WARN- ING".

under

the

If, after reading this manual, you have any questions regarding the operation of your vehicle, please contact your nearest Hyundai Motor America Regional Office as listed in the following:

88

Eastern Region: Connecticut, Delaware, Maine, Massachusetts, New Hampshire, New Jersey, New York, Pennsylvania, Rhode Island, Vermont.

Central Region: Illinois, Indiana, lowa, Kentucky, Minnesota, Nebraska, North Dakota, South Dakota, Ohio, Wisconsin, Kansas, Missouri.

Michigan,

Eastern Region 1100 Cranbury South River Road Jamesburg, NJ 08831
(800) 633-5151

Central Region 1705 Sequoia Drive Aurora, Illinois 60506
(800) 633-5151

Southern Region: Florida, Georgia, Maryland, North Carolina, South Carolina, Virginia, West Virginia.

Western Region: Alaska, Hawaii, Arizona, California, Colorado, ldaho, Montana, Nevada, Oregon, Utah, Washington, Wyoming.

Western Region 10550 Talbert Avenue P.O.Box 20850
Fountain Valley, California 92728-0850
(800) 633-5151

Southern Region 270 Riverside Parkway, Suite A Austell, GA 30168
(800) 633-5151

South Central Region: Alabama, Arkansas, Louisiana, Mississippi, New Mexico, Oklahoma, Tennessee, Texas.

South Central Region 1421 South Beltline Road, Suite 400
Coppell, TX 75019
(800) 633-5151

Specifications, Consumer information, Reporting safety defects

REPORTING SAFETY DEFECTS BINDING ARBITRATION (U.S.A ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying HYUNDAI MOTOR AMERICA. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or HYUNDAI MOTOR AMERICA. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888- 327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA 1200 New Jersey Ave SE West Building Washington, D.C. 20590. You can also obtain other informa- tion about motor vehicle safety from http://www.safercar.gov.

Any claim or dispute you may have relat- ed to your vehicle's warranty or the duties contemplated under the warranty, includ- ing claims related to the refund or partial refund of your vehicle's purchase price (excluding personal injury or product lia- bility claims), shall be resolved by binding arbitration. Binding arbitration shall be administered by and the American Arbitration Association (AAA). You will not be responsible for paying fil- ing and hearing fees above $275.00. All other arbitration costs shall be borne by Hyundai Motor America. You are not responsible to pay any of the costs Hyundai incurs. This Binding Arbitration Agreement shall not deprive you of any remedies avail- able to you under applicable law. The parties are waiving their right to seek remedies in court, including the right to a jury trial.

through

revoke

This Binding Arbitration Agreement shall be governed by and interpreted under the Federal Arbitration Act, 9 U.S.C. sec- tions 1-16. Judgment upon any award may be entered in any court having juris- diction. this Arbitration You may Agreement by (1) written notice or (2) electronic notice. Written notice must be delivered (via certified mail) to Hyundai Motor America, Attn: Consumer Affairs, 10550 Talbert Avenue, P.O. Box 20849, Fountain Valley, CA 92728-0849. Electronic notice must be submitted at the following website address: http://war- ranty-arbitration.hyundaiUSA.com. Notice must be received within 90 days after you purchase your vehicle.

8 9